Assembly Manual

Size: px

Start display at page:

Download "Assembly Manual"

Clarence Victor Cannon
5 years ago
Views:

1 Assembly Manual

Prepare & Position the Sauna Floor If you are assembling your sauna on a hard surface

sauna floor. Place the sauna floor in the desired location.

sauna following assembly. It is important that the sauna floor is level.

2 Prepare & Position the Sauna Floor If you are assembling your sauna on a hard surface floor it is recommended that you apply the included adhesive felt to the bottom of the sauna floor. Place the sauna floor in the desired location. It is necessary to position the floor out from your walls for assembly and move the sauna following assembly. It is important that the sauna floor is level. Checking with a large level is recommended. If the floor is not level, shimming or other remedies should be applied before assembling the sauna.

Position the Front Wall Lift the front wall into position carefully lowering the bottom of the

3 Ensure that the door heater electrical is protruding from bottom of front wall frame A bit of plastic wrap can serve to hold the connector out slightly. Position the Front Wall Lift the front wall into position carefully lowering the bottom of the wall into the channel on the floor base. Prop up one end of the front wall to enable connection of the door heater electrical lead.

Connect door heater electrical lead to the

4 Connect door heater electrical lead to the floor base. Ensure hat the threaded cuff is fully screwed onto the floor base connector. Position Right Side Wall Lift the Right side wall into position wedging the bottom of the wall into the channel in the floor base.

3/4 while holding the front wall down It is helpful if a second person applies pressure against the opposite edge of the front wall.

5 Connect Side & Front Wall Cinch the two walls together by applying pressure on the outside of the side wall with your knee Slide the side wall upward approx. 3/4 while holding the front wall down It is helpful if a second person applies pressure against the opposite edge of the front wall. This will help ensure that the two walls remain in contact and the fasteners connect. The 2 sets of fasteners for the walls will connect when the side wall is raised sufficiently. Slide the side wall down while continuing to cinch the two walls together.

Check to ensure that both sets of fasteners have connected by looking at the

It is possible to connect one set of fasteners and miss the other.

not connected and the raising and lowering procedure will need to be repeated.

6 Check to ensure that both sets of fasteners have connected by looking at the corner inside of the sauna. It is possible to connect one set of fasteners and miss the other. If there is an obvious gap in the corner between the two walls the fasteners have not connected and the raising and lowering procedure will need to be repeated. Repeat procedure to connect the Back Wall to the Right Side Wall. Raise the side wall up. Slide the side wall down while continuing to cinch the two walls together

Repeat the lifting up and sliding down procedure again to connect the

7 Position Left Side Wall Lift the Left side wall into position wedging the bottom of the wall into the channel in the floor base. Repeat the lifting up and sliding down procedure again to connect the Left Side wall to Back and Front Wall working on one corner at a time Side Wall lifts up

Prepare to install the sauna roof Fish the plastic electrical connector out from inside the

If the connector can not be fished out it may be necessary to remove access panel on top of

If you are installing the sauna in a restrictive space and are unable to walk down the sides

8 Prepare to install the sauna roof Fish the plastic electrical connector out from inside the roof before lifting the roof. If the connector can not be fished out it may be necessary to remove access panel on top of roof. Install the Sauna Roof Lift the roof up and over top of the sauna walls. If you are installing the sauna in a restrictive space and are unable to walk down the sides of the saunas, it may be necessary for one person to go inside the sauna. Hook the right side corners of the roof over the walls then lower the roof toward the left of the sauna.

snaps together connectors and then feeds the connector up into roof.

9 Connect Roof Wires Before lowering the roof, connect the 12 V power supply wires. This is easiest accomplished with one person holding the weight of the roof while the other snaps together connectors and then feeds the connector up into roof. Lower Roof into Position It may be necessary to push on the inside or outside of the side and back wall to enable to roof to drop into position.

Electrical Connections Inside of Sauna Connect

'D-Sub' computer style connector as shown Plug in

10 Electrical Connections Inside of Sauna Connect the circular connector to power supply box. Align the groove in connector to properly insert. Thread the cuff of connector on fully Attach the 'D-Sub' computer style connector as shown Plug in all heater leads to receptacles in the power supply box.

Feed the main power supply cord in through the hole in back wall

Do NOT plug power cord into your wall outlet until all electrical

Connect circular connector for the door heater.

11 Feed the main power supply cord in through the hole in back wall and insert in power supply box. Do NOT plug power cord into your wall outlet until all electrical connections are finished inside of the sauna. Connect circular connector for the door heater. Thread the cuff of connector on fully. When all connections are made inside of the sauna, plug the sauna's main power cord into wall outlet.

It is necessary to remove the heater guards from the two side walls in order to install the leg heater

12 Remove Side Wall Heater Guards The wooden lattice work in front of the heaters is referred to as the heater guard. These are held on with strong magnets. It is necessary to remove the heater guards from the two side walls in order to install the leg heater and the sauna bench. Leg Heater Install the leg heater by lowering it into the brackets mounted on the side walls. Plug leg heater into the power supply box in floor.

13 Install Bench The bench in your new sauna is reversible. Choose whichever side appeals to you to face upward. Reinstall the side wall heater guards Install the door handle

Audio System Music can be piped to the speakers in the sauna two different ways, either wireless via the Bluetooth receiver or by directly connecting your

Bluetooth Mode Search for and pair your device's Bluetooth to the 'BT speaker'. 2.

14 Audio System Music can be piped to the speakers in the sauna two different ways, either wireless via the Bluetooth receiver or by directly connecting your device (smart phone, tablet, laptop etc.) with a 3.5mm male to male audio cord (Red audio cord pictured NOT included). 1. Bluetooth Mode Search for and pair your device's Bluetooth to the 'BT speaker'. 2. Direct Connect Mode: Remove access panel from roof by unscrewing wood screws.connect your device to the saunas' speakers via your device's headphone jack by inserting 3.5 mm audio cord into the BTcircuit board as shown. Connecting an audio cord will disable the Bluetooth.

15 Reinstall the roof panels and feed your audio cord through the hole in roof.

Movable Bench Assembly (Special order only for Evolve 10

of the frames Attach the leg assembly to the bottom of the

16 Movable Bench Assembly (Special order only for Evolve 10 model) Connect bench legs to the inside corners of the frames using supplied wood screws. Ensure that the legs' ends are flush with the bottom edge of the frames Attach the leg assembly to the bottom of the bench surface. Choose which surface of the bench you prefer to be the top and bottom.

17 Chromatherapy Lighting The color LED light panel is controlled by the remote control and is NOT connected to the sauna wall controller.

18 Care and Maintenance It is advisable that you always sit on towels when using your sauna to minimize any sweat stains on the wood surfaces. Following use, wipe wood with damp cloth of any sweat that soaks through your towels etc. to minimize staining of the wood. The carbon panel heaters in your Sun Stream sauna can be gently wiped of any sweat, dust etc. A damp cloth is usually all that is needed to clean the heater surfaces. Floor Heater Cleaning It is common for sweat to drip through the floor grate and onto the floor heater surface Gently wipe the floor heater after use of any sweat that has dripped down through the floor grate. A damp cloth is usually adequate. Do NOT scrub the floor heater or other heaters with excessive pressure. For accumulated dirt and sweat, if necessary, use a bit of dish soap or gentle cleaner on the heaters.

19 Control Panel

20 Interior Control Panel Temperature Sensor FRAGILE DO NOT TOUCH

21 Connecting the sauna to your house power supply When the sauna is plugged into you wall outlet the red Power Indicator light on the control panel will be on. The Bluetooth audio receiver on the roof will make a beeping noise its indicator light will turn on. ON/OFF for Heaters Push the POWER button to turn the sauna heaters ON. The various displays will come on. The sauna heaters will remain ON until the timer runs down to 00. The sauna heaters can be turned OFF at any time by pushing the POWER button. Timer Adjustment The default time is 60 minutes. Press + or - to change the Timer setting. The maximum setting is 60 minutes. The minimum setting is 5 minutes. Pre Heat Sun Stream Infrared Saunas are typically used by preheating the sauna for minutes. Thermostat Adjustment Press + or - to change the Thermostat setting. Increase Thermostat Setting: Press the + button to increase the temperature by 1 degree C increments. The maximum setting is 65 C. Decrease Thermostat Setting: Press the - button to decrease the temperature by 1 degree C increments. The minimum setting is 25 C.

Temperature Control When the interior air temperature is below the Thermostat set temperature, the heaters will remain ON.

22 Thermometer /Thermostat Display When the POWER button is turned ON the digital display will show the Thermometer reading. Anytime the + and - buttons are pushed the Thermostat setting display will show. After setting the thermostat the display will return to displaying Thermometer reading. Temperature Control When the interior air temperature is below the Thermostat set temperature, the heaters will remain ON. When the interior temperature is higher than the Thermostat set temperature, the power to the heaters will be turned OFF. The heater panels will begin to cool down, air temperature and Infrared levels will slowly drop until the Thermostat is activated and the power to the heaters will be turned back on. AII (Adjustable Infrared Intensity) The Intensity button on the control panel will adjust the Infrared intensity much like a dimmer switch for a household light. Press the Intensity button to select 100%, 75% or 50 % levels of Infrared intensity for different purposes and individual needs.

23 Enjoy your new Sun Stream Evolve Infrared Sauna!

Assembly Manual. Supreme One, Supreme Two, Supreme Three. Tel

Assembly Manual. Supreme One, Supreme Two, Supreme Three. Tel Assembly Manual Supreme One, Supreme Two, Supreme Three Prepare & Position the Sauna Floor If you are assembling your sauna on a hard surface floor it is recommended that you apply the included adhesive