FLOOR CONSOLE / UNDER CEILING DUAL type

Transcription

1 SPLIT TYPE ROOM AIR CONDITIONER FLOOR CONSOLE / UNDER CEILING DUAL type Models Indoor unit ABU8RULX ABURULX Outdoor unit AOU8RLX AOURLX CONTENTS SPECIFICATIONS... OUTLINE AND DIMENSIONS... REFRIGERANT SYSTEM DIAGRAM... CIRCUIT DIAGRAM... PCB CIRCUIT DIAGRAM... 7 ERROR DISPLAY... DISASSEMBLY ILLUSTRATION (Indoor Unit)... DISASSEMBLY ILLUSTRATION (Outdoor Unit)... 0 PARTS LIST (Indoor Unit)... PARTS LIST (Outdoor Unit)... 6 ACCESSORIES... 7

2 SPECIFICATIONS TYPE Cool and Heat INDOOR UNIT OUTDOOR UNIT COOLING CAPACITY ABU8RULX AOU8RLX 7,800 / 7,800 BTU/h ABURULX AOURLX,00 /,00 BTU/h HEATING CAPACITY,00 /,00 BTU/h,00 /,00 BTU/h ELECTRICAL DATA POWER SOURCE 0 V / 08 V FREQUENCY 60 Hz RUNNING CURRENT (Cool) 7. A / 7.9 A 9.8 A / 0.9 A RUNNING CURRENT (Heat) INPUT WATTS (Cool) 9.8 A / 0.9 A.6 kw /.6 kw 0. A /. A. kw /. kw INPUT WATTS (Heat) E.E.R. (Cool). kw /. kw.9 /.9 kw/kw. kw /. kw.89 /.89 kw/kw E.E.R. (Heat) MOISTURE REMOVAL ( /hr).80 /.80 kw/kw. L/hr.0 /.0 kw/kw. L/hr AIR CIRCULATION-Hi (m /hr) 780 m /hr 880 m /hr COMPRESSOR TYPE DISCRIMINATION REFRIGERANT R0A Hermetic type, poles, Inverter, Twin Rotary TNB0FPBM9 lb oz (,900 g) FAN MOTOR POWER SOURCE DISCRIMINATION INDOOR UNIT HIGH-SPEED ( Cool / Heat ) MED-SPEED LOW-SPEED OUTDOOR UNIT DISCRIMINATION ( Cool / Heat ) HIGH- SPEED 0 V MFA-PPT MFA-PPT,060 /,060 r.p.m.,80 /,00 r.p.m. 890 / 890 r.p.m.,000 /,000 r.p.m. 770 / 770 r.p.m. 900 / 900 r.p.m. MFE-ROM MFE-ROM 780 / 780 r.p.m. 80 / 900 r.p.m. DIMENSIONS INDOOR UNIT OUTDOOR UNIT HxWxD HxWxD 7-7/8" x 9-/8" x -7/8" inch (99 x 990 x 6 mm) -/" x -/" x " inch (80 x 900 x 0 mm) WEIGHT INDOOR UNIT OUTDOOR UNIT Gross / Net Gross / Net 7 kg / 8 kg 70 kg / 6 kg REFRIGERANT CHARGE (R0A) Pipe Length FULL CHARGE AMOUNT 9 ft. ( m) lb oz (,900 g) 66 ft. (0 m) lb 7oz (,000 g) 98 ft. (0 m) lb oz (,00 g) ft. (0 m) lb oz (,00 g) 6 ft. (0 m) lb oz (,600 g) ADDITIONAL REFRIGERANT 0.oz / ft. (0 g/ m) lb oz (,900 g) lb 0oz (,00 g) lb 8oz (,00 g) 6 lb 6oz (,900 g) 7 lb oz (,00 g) 0. oz / ft. (0 g/m)

3 OUTLINE AND DIMENSIONS INDOOR UNIT Models : ABU8RULX, ABURULX Unit : inch (mm) -7/8" (6) 9-/8" (990) 7-7/8" (99) (rear view) " (900) 9-/" (00) 0-7/8" (0) -/6" ( 00) -/" (0) -/" (70) 7-7/" (99) 6-7/8" (7) 7-7/8" (00)

4 OUTDOOR UNIT Models: AOU8RLX, AOURLX Unit : inch (mm) -/" (900) "(77) -/" () " (0) /" () -/" (80) 7/8" () 7-/8" (0) /8" (9) -/" (00) -/8" (60) Air Flow -/8" (70) -7/8" (99) 7-/" (96) -/" (7) 6-/" (70) 00..8

5 REFRIGERANT SYSTEM DIAGRAM Models : ABU8RCLX / AOU8RLX OUTDOOR UNIT INDOOR UNIT Pressure Check Valve Refrigerant Pipe.7mm (/") High Pressure Switch Charging Valve Condenser Muffler -way Valve Evaporator Accumulator Compressor Expansion Valve Refrigerant Pipe 6.mm (/") Strainer Strainer Charging Valve Models : ABURULX / AOURLX OUTDOOR UNIT INDOOR UNIT Pressure Check Valve Refrigerant Pipe.88mm (/8") High Pressure Switch Charging Valve Condenser Muffler -way Valve Evaporator Accumulator Compressor Expansion Valve Refrigerant Pipe 9.mm (/8") Strainer Strainer Charging Valve : COOL : HEAT 00..8

6 CIRCUIT DIAGRAM Models : ABU8RULX, ABURULX ROOM TEMPERATURE THERMISTOR PIPE TEMPERATURE THERMISTOR INDICATOR PCB ASSY FAN MOTOR CN0 FM GREEN / YELLOW Use T.A-0V Fuse on F BROWN RED ORANGE YELLOW BLUE PURPLE GRAY RED PINK PURPLE BLUE GRAY GRAY CN RED BROWN RED ORANGE YELLOW BROWN RED ORANGE YELLOW 6 CN CN7 CN CN7 CN8 CONTROLLER PCB ASSY CN CN0 CN FAN MOTOR CAPACITOR M M STEP MOTOR (UP/DOWN) STEP MOTOR ( LEFT / RIGHT ) GREEN L N POWER SUPPLY PCB G RED TERMINAL 00..8

7 Models : AOU8RLX, AOURLX COMPRESSOR CHOKE COIL U PIPE TEMPERATURE THERMISTOR DISCHARG TEMPERATURE THERMISTOR BROWN EMI FILTER CONNECTOR T RED RED V W ACTIVE FILTER MODULE TERMINAL L L + - BROWN RED ORANGE YELLOW 6 P N YELLOW BLUE EMI FILTER T RED BROWN U W0 V W0 W W0 W W W6 W7 W0 W CN BLUE BROWN CN CN CN CN6 CN CN07 FUSE F T A-0V CN7 CN80 CN7 CN W00 RED RED CN0 CONTROLLER PCB ASSY FUSE F T.A-0V RED YELLOW BLUE 6 RED BROWN BLUE ORANGE YELLOW 6 OUTDOOR TEMPERATURE THERMISTOR COMPRESSOR TEMPERATURE THERMISTOR HEAT SINK TEMPERATURE THERMISTOR WV FM EV HIGH PRESSURE SWITCH SOLENOID COIL FANMOTOR EXPANSION VALVE COIL TM0 BROWN RED CN W9 W8 POWER SUPPLY PCB ASSY TM0 W W6 W7 W W GREEN RED G EARTH (N) L N G EARTH

8 INDOOR PCB CIRCUIT DIAGRAM Models : ABU8RULX ABURULX CONTROLLER PCB ASSY ABU8RULX : K0AL-00PHSE-C ABURULX : K0AL-00SHSE-C 7

9 OUTDOOR PCB CIRCUIT DIAGRAM Models : AOU8RLX AOURLX POWER SUPPLY PCB ASSY K0BA-000HUE-P INVERTER ASSEMBLY AOU8RLX : EZ-00GHUE AOURLX : EZ-00FHUE CONTROLLER PCB ASSY AOU8RLX : K0AW-00HUE-C AOURLX : K0AW-00HUE-C 8

10 00..8 Models : AOU8RLX, AOURLX CONTROLLER PCB ASSEMBLY ( MAIN PCB ) AOU8RLX : K0AW-00HUE-C AOURLX : K0AW-00HUE-C 9 600/0V x

11 Models : AOU8RLX, AOURLX POWER SUPPLY PCB ASSEMBLY K0BA-000HUE-P0 * AOU8RLX, AOURLX : W and W AOU6RLX, AOURLX : W and W POWER SOURCE 0V 60Hz * * W or W W or W B B VA0 70V <TNR> VA0 70V <TNR> C0. <LE> SA00 RA-0M L RCH70-0PF07 C0 0.0 <YE> C0 0.0 <YE> C06. <LE> TM00 L N0000KD7C C07. <LE> TO INDOOR UNIT W6 W7 B B CT CT-B EARTH W GREEN B V D60 DAN7U + AC VOLT OUT W8 W9 B B R60.0K </0W> (%) C60 0/6V <PJ> L RCH70-0PF07 C. <LE> C 0.0 <YE> C 0.0 <YE> VR BK R6.7K </0W> (%) R68 K </0W> C6 0. <F> C6 0. <F> V TM0 TM0 CN BB-XASK--A CT OUT

12 ERROR CONTENTS (Indoor unit) OERATION TIMER SWING SWING OPERATION lamp (Red) TIMER lamp (Green) SWING lamp (Orange) SWING lamp (Orange) MANUALAUTO Operation can be checked by lighting and flashing of the display section OPERATION,, and TIMER lamps. Perform judgment in accordance with the following. TEST RUNNING When the air conditioner is run by pressing the remote control unit test run button, the OPERATION and TIMER lamps flash slowly at the same time. ERROR The OPERATION, TIMER, and SWING lamps operate as follows (Table) according to the error contents. Error contents Error display OPERATION TIMER SWING (RED) (GREEN) (ORANGE) Indoor unit circuit board error Indoor unit room temperature sensor wire opened Indoor unit room temperature sensor wire short circuited Indoor unit piping sensor wire opened Indoor unit piping sensor short circuited Indoor unit fan error Outdoor unit circuit board error Miswiring between outdoor unit and indoor unit times times times times 6 times times times Outdoor unit discharge temperature sensor error Outdoor unit piping sensor error Outdoor unit outdoor temperature sensor error times times times : Fast flashing : Slow flashing : Off

13 ERROR CONTENTS (outdoor unit). Make a TEST RUN in accordance with the installation instruction sheet for the indoor unit.. OUTDOOR UNIT LEDS When a malfunction occurs in the outdoor unit, the LED on the circuit board lights to indicate the error. Refer to the following table for the description of each error according to the LED. LED Error contents. When the product is operating: Press the PUMP DOWN switch on the outdoor unit. The LED on the outdoor unit circuit board lights, and operation stops. At this point, recovery has not been completed, so do not close the two- and three-way valves. The pump down operation (cooling operation) begins after three minutes. Close the three-way valve (liquid) after operation starts. flash flash flash flash 7 flash 8 flash 9 flash flash flash flash flash 6 flash lighting Communication error (Indoor unit - Outdoor unit) Discharg pipe temperature sensor Outdoor heat exchanger temperature sensor Outdoor temperature sensor Compressor temperature sensor Heat sink temperature sensor Pressure switch abnormal IPM error Compressor rotor position cannot detect Compressor cannot operate Outdoor fan abnormal (upper fan) Outdoor fan abnormal (lower fan) No error After - minutes, operation stops. Close the threeway valve (gas) within one minute after operations stops. The LED will go out three minutes after it stops. Disconnect the power supply after confirming that the LED has gone out. *When the pump down operation is repeated, temporarily disconnect the power supply after opening the closed valves (both liquid and gas). Reconnect the power supply after - minutes and perform the pump down operation. *When the start of the operation after pump down operation has been completed, temporarily disconnect the power supply after opening the closed valves (both liquid and gas). Reconnect the power supply after - minutes and be sure to perform a test operation for cooling. -way valve (Liquid) SPECIAL INSTALLATION SETTING PUMP DOWN (Refrigerant collecting operation) Perform the following procedures to collect the refrigerant when moving the indoor unit or the outdoor unit.. When the product is stopped: -way valve (Gas) PUMP DOWN SW (SW) Press the PUMP DOWN switch on the outdoor unit. (The LED on the outdoor unit circuit board lights.) The pump down operation (cooling operation) begins right away. After oparation starts, close the three-way valve (liquid). After - minutes, operation stops. Close the threeway valve (gas) within one minute after operations stops. The LED will go out three minutes after it stops.disconnect the power supply after confirming that the LED has gone out. DANGER This part (Choke coil) generates high voltages. Never touch this part

14 DISASSEMBLY ASSEMBLY Models : ABU8RULX, ABURULX

15

16

17 INDOOR UNIT

18 OPTIONAL PARTS

19

20

21 Models : AOU8RLX AOURLX

22 Models : AOU8RLX AOURLX

23 Models : AOU8RLX AOURLX

24 Models : AOU8RLX AOURLX

25 PARTS LIST INDOOR UNIT Ref. No. Description ABU8RULX Part No. ABURULX Ord. Q'ty 8 Air Filter Capacitor (Fan Motor) Sirocco Fan Assy Rubber (Vibration-proof) Cap, Plastic Louver Base Assy Casing, Plastic Kit (Dew Proof Plate) Motor Fixing Table Assy Drain Hose Assy Kit (Separate Wall-A) Evaporator Assy KB Drain Pan Assy (Kit) Fan Motor Assy-IN Hanger Bracket-L Hanger Bracket-R Thermistor Spring-A Clamp No Clamp SKB Clamp SKB-M Control Box Thermistor Assy-Room Thermistor Assy-Pipe Controller PCB Assy (K0AL-00PHSE-C) (K0AL-00SHSE-C) 0 Remote Control Unit Flap (Upper)-F Flap (Lower) Motor Fixture Bushing Bushing-B, Plastic Bushing-C, Plastic Special Screw Special Screw Locking Spacer, KGLS-S Indicator PCB Assy Motor Rod Louver Link Insulation (Panel)-A Insulation (Panel)-B Insulation (Flap Base) Arm Bracket Separate Wall-B (Kit) Grille Support Filter Bracket Grill-F When you order parts, please make a photocopy of this page and fill the number of the parts in the "Order" column.

26 INDOOR UNIT (Continued) Ref. No. Description ABU8RULX Part No. ABURULX Ord. Q'ty 00 Protect Cover Support Stay Louver Shaft Louver Stopper Louver Rod Cosmetic Panel-R Cosmetic Panel-L Control Box Cover Flap Base Louver Link Cover Flap Link-Upper (Step Motor-V) Flap Link-Lower (Step Motor-V) Motor Rod-A (Step Motor-V) Catch TL Base Bracket (Reinforcement Metal) Top Cover Protector, Metal (Fan Motor) Cord Bushing KR Locking Spacer-B Thermistor Holder Pipe Bolt Motor Base Holder (Guide Rail) Distributor Assy Remote Control Unit Holder Casing Cover Drain Cap Panel Bypass Pipe Assy Terminal 7P Fuse BET.A - 0V Arm Power Supply PCB Assy (K0AL-00PHSE-PO) (K0AL-00PHSE-PO) 876- Step Motor-H Step Motor-V EMI Filter When you order parts, please make a photocopy of this page and fill the number of the parts in the "Order" column.

27 OUTDOOR UNIT Ref. No. Description AOU8RLX Part No. AOURLX Top Panel Sub Assy Front Panel Fan Guard Grip Side Service Panel Sub Assy Right Panel Emblem Rear Propeller Fan Assy Motor, Induction Condenser-A Assy Ord. Q'ty Strainer Assy Separate Wall Assy Cap Foot Base Assy Way Valve Assy (/8") Way Valve Assy (/") Way Valve Assy (/8") Way Valve Assy (/") Check Joint Assy Compressor Assy Way Valve Solenoid Pressure Switch Inlet Pipe Cond A Assy Inlet Pipe Cond B Assy Outlet Pipe Cond A Assy Expansion Valve Assy Coil (Expansion Valve) Distributor Discharge Pipe A Assy Terminal P Terminal P ACTPM Holder Thermo Inverter PCB Assy Power PCB Assy Motor Bracket Sub Assy Choke Coil Fuse.A-0V Thermistor (Outdoor Temp.) Heat Exchanger Thermistor Thermistor (Discharge) Compressor Thermistor Thermistor Heatsink Thermistor Transformer Varistor Arrester Relay Relay Switch Push Switch Slide Drain Pipe Assy Drain Cap Coil Choke When you order parts, please make a photocopy of this page and fill the number of the parts in the "Order" column.

28 STANDARD ACCESSORIES The following installation parts are furnished. Use them as required. INDOOR UNIT ACCESSORIES Name and Shape Q'ty Application Part No. Cosmetic Panel-L Cosmetic Panel-R 980 Tapping screw ( x 0) Installation template For positioning the indoor unit. For under ceiling type Hanger bracket (left) For suspending the indoor unit from ceiling Hanger bracket- (right) Anchor bolt (M) Special nut Spring washer Wall bracket For suspending the indoor unit on the wall Tapping screw ( x 0) 6 For fixing the wall bracket Coupler heat insulator (large) For indoor side pipe joint. (Large pipe) Coupler heat insulator (small) For indoor side pipe joint. (Small pipe) 0980 Nylon fastener For fixing the drain hose Drain hose Insulation (drain hose) Adhesive type 70 x VT wire For fixing the drain hose L 80 mm

29 REMOTE CONTROL UNIT Name and Shape Q'ty Application Part No. Remote control unit Use for air conditioner operation (AR-JW) Battery (penlight) For remote control unit Remote control unit holder Hold the remote control unit 9060 Tapping screw ( x ) For remote control unit holder installation Wired remote controller unit is also available : UTB-UUB (Parts No ) OUTDOOR UNIT ACCESSORIES Name and Shape Q'ty Application Part No. Drain pipe Drain cap For outdoor unit drain piping work (May not be supplied, depending on the model)

30 0G98