BIGBANG - PJT TRAINING MANUAL

Transcription

1 SAMSUNG Clothes Washer BIGBANG - PJT TRAINING MANUAL Jan Digital Appliances Division

2 CONTENTS 1. Features 2. Changed Part List 3. Operation 4. Test Mode & Error Check 5. Reference Information 6. Disassembly & Reassembly

3 1.Product Introduction 1-1. Concept V.R.T (Vibration Reduction Technology) : the lowest vibration & noise level Extra-Capacity (4.0 Cu.ft. IEC) Stylish Design Main Feature Sub. Feature Vibration Reduction Technology Extra-Capacity (4.0 Cu.ft. IEC) Direct Drive Inverter motor Tender Drum Delay Start: up to 19 hours Child Lock Woolmark Certified(WF220) Sanitize(WF220) Pure Cycle(WF220)

4 1.Product Introduction 1-2. Sales Point & Product Positioning Brand Samsung (Big Bang) LG Whirlpool GE Design Model WF220ANW WF210ANW WM2016CW WFW8400TW WCVH6800JWW Retail price (white) $699 $599 $699 $699 $799 Key Sales point USP & Spec Design VRT, PureCycle VRT Direct Drive System E-Star Tier 3 CU "Best Buy" Capacity 4.0 cu.ft 4.0 cu.ft 3.6 cu.ft 3.7 cu.ft 4.0 cu.ft MEF WF kwh/year 140kWh/year 140kWh/year 160kWh/year 156kWh/year 142kWh/year VRT Yes Yes RPM 1,100 1,100 1,050 1,000 1,100 Motor DD motor DD motor DD motor 3 phase 3 phase Cycle # Heater(900W) Yes No No No Yes Options Delay start, Extra rinse, PureCycle Delay start, Extra rinse, MyCycle Display 18:88 seg. 18:88 seg. 18:88 seg. 88 seg. 8:88 seg. Color White White White White White Door Silver White Silver White White WXDXH 27 X 31 X 38" 27 X 31 X 38" 27 X 29.8 X 38.7" 27 X 30.5 X 36" 27 X 31.6 X 40.6"

5 1.Product Introduction 1-3. Product Dimension Dimension Height-Overall (A) Width (B) Depth with Door Open at 90 Degrees Inch (Cm) 38 (96.5) 27 (68.6) 50.8 (129) (C) Depth (D) 31.1 (80)

6 2.Changed Part List 2-1. ASSY PANEL CONTROL Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features Washing cycle consist of 10 courses Gray-colored KNOB Washing cycle consist of 6/8 courses (WF210/WF220) Silver-colored KNOB

7 2.Changed Part List 2-2. ASSY PANEL DRAWER Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features Bended PANEL-DRAWER Wide PANEL-DRAWER

8 2.Changed Part List 2-3. ASSY FRAME FRONT Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features COVER-FILTER is on the right bottom. COVER-FILTER is on the left bottom.

9 2.Changed Part List 2-4. WEIGHT BALANCER Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features WEIGHT-BALANCERS exist on both sides of TUB. WEIGHT-BALANCERS exist on upside and down side of TUB.

10 2.Changed Part List 2-6. MOTOR Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW Shape Features COVER-MOTOR is changed. WF220ANW

11 2.Changed Part List 2-7. ASSY DRUM Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features Capacity : 3.8 CU. FT T=0.6mm Capacity : 4.0 CU. FT(WF210) Capacity : 4.0 CU. FT(WF220) T=0.5mm

12 2.Changed Part List 2-8. ASSY FRAME Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features T=1.0mm T=0.8mm

13 2.Changed Part List 2-9. ASSY-FRAME Div Basic ( Frontier4 ) Big Bang Shape Features Cushion : 2T X 100 X 100 No cushion inside frame for tub.

14 2.Changed Part List HOSE DRAWER-TUB Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features Water supply from front of TUB Water supply from side of TUB

15 2.Changed Part List ASSY DOOR Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features Door-safety. No door-safety. White(WF210) / Imperial silver(wf220).

16 2.Changed Part List Heater Div Basic ( Frontier4 ) Big Bang WF218ANW WF220ANW Shape Features Wire comes from left side. Wire comes from right side(wf220 only).

17 2.Changed Part List ASSY PCB (M) Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features Heater relay switch. Heater relay : X (WF210) Heater relay : O (WF220)

18 2.Changed Part List ASSY PCB (S) Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features Quantity of LED : 14 EA Quantity of LED : 6 EA (WF210) / 8EA(WF220)

19 2.Changed Part List ASSY PCB (C) Div Basic ( Frontier4 ) WF218ANW Big Bang WF210ANW WF220ANW Shape Features Quantity of LED : 29 EA Tact switch : 6 EA Quantity of LED : 22 EA Tact switch : 9 EA

20 2.Changed Part List 2-8. Software Div Basic ( Frontier 4) WF210ANW WF220ANW Display Method Graphic LED Graphic LED Graphic LED Course Extra Wash My Cycle Pure Cycle Extra Rinse Extra Rinse Extra Rinse Delay Start Delay Start Delay Start Option

21 3.Instruction of Function 3-1. Control Panel :WF220 ONLY WF210: Digital graphic display Displays the remaining cycle time, all cycle information, and error messages 2. Temperature Selection Button Press the button repeatedly to cycle through the different water temperature options. Hot/Cold Whites and heavily soiled, colorfast items. Warm/Warm Colorfast items. When warm rinse is selected, only the final rinse will be warm. The other rinses will be cold to conserve energy. Warm/Cold Moderately soiled, colorfast items; most wrinkle-free items. Cold/Cold Brightly colored, very lightly soiled items

22 3.Instruction of Function 3-1. Control Panel :WF220 ONLY WF210: Spin Selection Button Press the button repeatedly to cycle through the different spin speed options. High - Use for underwear, t-shirts, jeans and sturdy cottons. Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics. Low - Use for delicate items needing a slow spin speed. No Spin - Drains your Washer without spinning. Use for extremely delicate items that cannot tolerate any spin

23 3.Instruction of Function 3-1. Control Panel :WF220 ONLY WF210: Soil Level Selection Button Press the button to select the Soil Level/washing time. Heavy - For heavily soiled loads. Normal - For moderately soiled loads. This setting is the best for most loads. Light - For lightly soiled loads. 5. Signal Selection Button Press the button to increase or decrease the end of cycle signal volume or turn off the signal

24 3.Instruction of Function 3-1. Control Panel :WF220 ONLY WF210: Select Cycle Option Delay Start - Any cycle can be delayed for up to 19 hours in one-hour increments. Extra Rinse - Add an additional rinse at the end of the cycle to more thoroughly remove laundry additives and perfumes. My Cycle Choose your favorite cycle including temperature, spin, soil level, option, etc.(wf210) Pure Cycle Use for drum cleaning. It cleanses drum of dirt and bacteria. Regular use (after every 40 washes) is recommended. No detergent or bleach needed.(wf220) 8 9 5

25 3.Instruction of Function 3-1. Control Panel :WF220 ONLY WF210: Cycle Selector Select the appropriate cycle for the type of load. This will determine the tumble pattern and spin speed for the cycle. Normal - For most fabrics including cottons, linens and normally soiled garments. Heavy duty - For sturdy, colorfast fabrics and heavily soiled garments. Perm Press - For wash-and-wear, synthetic fabrics and lightly to normally soiled garments. Sanitize - For heavily soiled, colorfast farments. This cycle heats the water to 150 F to eliminate bacteria(wf220). 9 5

26 3.Instruction of Function 3-1. Control Panel :WF220 ONLY WF210: Cycle Selector Delicates/Hand Wash - For sheer fabrics, bras, lingerie silk and other handwash-only fabrics. For best results, use liquid detergent. Wool - The machine-washable wool. Loads should be under 8 pounds(wf220). Quick Wash For lightly soiled garments needed quickly. Rinse+Spin Use for loads that need rinsing only or to add rinse-added fabric softener to a load

27 3.Instruction of Function 3-1. Control Panel :WF220 ONLY WF210: Start/Pause Selection Button Press to pause and restart programs. 9. Power Button Press once to turn your washer on, press again to turn your washer off. If the washer is left on for more than 10 minutes without any buttons being touched, the power automatically turns off

28 3.Instruction of Function 3-2. Child Lock This function prevents children from playing with your washer. Activating Press and hold both Spin and Soil Level buttons at the same time for 3sec. 5.If the Child Lock function is activated, the door is locked and the Child Lock lamp is lit. 2. If the Start/Pause button is pressed after the Child Lock function is activated, none of the buttons will work except for the Power button. 3. If a button is pressed when the buttons are locked, the Child Lock lamp blinks. Pausing the Child Lock function When the door is locked or the buttons are locked by the Child Lock function, you can pause the Child Lock operation for 1 minute by pressing and holding both the Spin and Soil Level buttons simultaneously for approximately 3 seconds. 1. If Child Lock mode is paused temporarily, the door lock is released for 1 minute for user convenience. During this period, the Child Lock lamp blinks. 2. If the door is opened after the minute is over, an alarm sounds for up to 2 minutes. 3. If the door is closed within the 2 minutes, the door is locked and the Child Lock function is reactivated. If the door is closed after the 2 minutes, the door will not be locked automatically and no alarm will be heard. Deactivating Press and hold both the Spin and Soil Level buttons simultaneously for approximately 6 seconds.

29 3.Instruction of Function 3-3. Spin Only If you press the Power button and then press and hold the Spin Only button for 2 seconds, the spin time is displayed on the display panel. Then repeat pressing the Spin Only button until the required spin level is selected and press the Start/Pause button Garment+ You can add or take out laundry items even after the wash has started, as long as the Garment+ light is turned on. Pressing the Start/Pause button unlocks the door, unless the water is too hot or if there is too much water in your washer. If you are able to unlock the door and wish to continue the wash cycle, close the door and press the Start/Pause button My cycle(wf210) Allows you to activate your custom wash(temperature, spin, soil level, etc.) with one-button convenience. By pushing the My Cycle button, you activate the settings used during the My Cycle mode. The My Cycle light will indicate activation. You can select all options as follows in the My Cycle mode. 4.Select cycle using the Cycle Selector. 5.After cycle selection, set each option. 6.Then, you can store the cycle and options you select by pressing the Start/Pause button in the My Cycle mode. The cycle and options you select will be displayed the next time you choose the My Cycle function.

30 3.Instruction of Function 3-6. Water Flow

31 4. Test Mode & Error Check 4-1. Test Mode Test Mode: Each Test Mode for the BIGBANG is as follows in the coming pages. The test modes indicated by the red arrows are modes unable to get an access once the washing cycle has started due to safety reasons.

32 4. Test Mode & Error Check Quick Test Mode Definition of Quick Test Mode: - Check operation of all LED s (Verify faulty LED). - Check model and software version. - Check different operating modes (e.g. water valve, motor, door, drain pump, etc.). How to Enter: - Plug in the unit. - Press Soil Key, Spin Key and Power Key at the same Time.

33 4. Test Mode & Error Check Quick Test Mode 1. All LED s light up and it sends out Beep Sound when it enters into the Quick Test Mode. (Including 7Segment) 2. Displays software version for a sec and Clear EEprom. (Ex. If S/W Version is 49, 7-Segment will display de49) 3. When the version is displayed, turn the Jog-Dial so that the version disappears. Press the following keys to test the various components. - Temp Key : Water Valve Test - Spin Key : Door Lock/Unlock Test - Soil Key : Water Heater Test Water Test - Signal : Drain Pump Test

34 4. Test Mode & Error Check EEPROM Clear Check Definition of EEPROM Clear Mode: - EEPROM initialization. -All course/option settings are to be reset to default values after EEPROM initialization. -When Service arises and it needs PCB replacement, EEPROM should be reset. How to Enter: - The unit needs to be on. - Press Delay Start Key, and Power Key at the same time.

35 4. Test Mode & Error Check Continuous Run Mode Definition of Continuous Run Mode: - Will continuously repeat the current cycle until the Continuous Run Mode is cancelled. How to Enter: - Press Delay Start Key and Extra Rinse Key together for 7 sec.

36 4. Test Mode & Error Check Continuous Run Mode Continuous Run Mode: 1. Press Delay Start + Extra Rinse Key for 7 sec during Power On State (Normal User Mode). 2. Once in Continuous Run Mode, The seven segments will no longer display 0000 and will alternate between displaying the number of cycles of the completed course and the remaining time of the course. 3. The Continuous Run Mode will repeat the previous cycle until continuous run mode is cancelled. 4. During Continuous Run Mode, press Delay Start + Extra Rinse Key for 7 sec to return to normal user mode. The seven segments will no longer display the number of cycles and will display the maintenance time only. 5. If you exit Service Mode after entering it from Continuous Mode, the washing machine returns to Continuous Mode. 6. If power is lost in Continuous Run Mode (that is, when the power plug is disconnected or the Power key is pressed turning the washing machine off), the mode is released when the washing machine is turned on again.

37 4. Test Mode & Error Check Service Mode Definition of Service Mode: - Service Mode enables service technicians to verify the operation of the washing machine and do troubleshooting. - Service Mode can be entered during all washing cycle without interrupting the cycle except some of test modes. - Various tests can be done with Service Mode. So, troubleshooting can be done based on the resulting diagnostic codes. How to Enter: - To enter the Service Mode, press the Signal and Extra Rinse Keys for 3 seconds or until the unit sends out beeping sounds.

38 4. Test Mode & Error Check Service Mode Special Test Mode: 1. The washer must be on to go into the Service Mode. 2. The motor speed will be displayed when started (It displays 0 when the motor does not spin). 3. The present state of the machine will not be changed. (i.e., the current cycle in progress will not be interrupted and only the display will change) 4. To exit Service Mode, press Signal and Extra Rinse Keys for 3 second again, or Power Key. If no key is operated during Service Mode for 5 minutes, the machine will return to normal user mode.

39 4. Test Mode & Error Check Quick Spin Test Mode Definition of Quick Spin Test Mode: - Quick Spin Test Mode is to do Spin Check. (High RPM) How to Enter: - During Service Mode, press the Delay Start and Temp. Keys for 3 seconds to enter Quick Spin Test Mode. - Cannot enter once the washing cycle has started.

40 4. Test Mode & Error Check Quick Spin Test Mode Quick Spin Test Mode: As it enters into the Quick Spin Test Mode, it starts spinning and reaches to its maximum RPM. Once the Spin speed reaches the maximum RPM, the speed drops immediately. To hold Quick Spin Test Mode (entering Hold Speed Mode), press the Start/Pause button. If the Start/Pause button is pressed during Quick Spin Test Mode, it will stop accelerating and hold its spinning speed for 10 minutes before going back to Quick Spin Test Mode. Also, to cancel the hold and allow Quick Spin Test Mode to continue, press the Delay Start and Temp Keys together for 3 seconds. If you hold down the Delay Start and Temp. keys for three (3) seconds when the washing machine is not in Hold Speed Mode, Quick Spin Mode is exited and Service Mode is restored.

41 4. Test Mode & Error Check Cycle Count Check Mode Definition of Cycle Count Check Mode: - Cycle Count Check Mode is to tally up the number of washings. How to Enter: - To enter the Cycle Count Check Mode, press the Signal Key during Service Mode. Cycle Count Check Mode: 1. Activate the Service Mode in advance. 2. When the Signal key is pressed, the total number of washings will light up and a signal LED will glow. 3. The maximum number of cycles will be 1999.The counter will roll over to 0 and start counting again after The counting will be carried out at the end of the normal cycle.(for normal and Continuous Run cycles, the count is carried out at the end of the cycles. 5. To exit the Cycle Count Check Mode, press the Signal key again.

42 4. Test Mode & Error Check S/W Version Check Mode Definition of S/W Version Check Mode: - S/W Version Check Mode is to bring up S/W Version information. How to Enter: - To enter the S/W Version Check Mode, press the Soil Level Key during Service Mode. S/W Version Check Mode: 1. Activate the Service Mode in advance. 2. Press the Soil Level Key to bring up its software VersionEX) Generate de49 at Version 49 (de is Micom code, 49 is it s software version) 3. To exit the S/W Version Check Mode, press the Soil Level S/W once again. Then, it returns to the Service Mode with motor RPM illuminating.

43 4. Test Mode & Error Check Fast Time Down Test Mode Definition of Fast Time Down Test Mode: - Fast Time Down Test Mode is to forward the program to the next cycle stage. How to Enter: - To enter the Fast Time Down Test Mode, press the Temp key during Service Mode. Each stage is located at key points of a complete cycle as follows: Fast Time Down Test Mode: - End of Each Fill (Beginning of Wash or Rinse Tumble Session)Caution: Check if the current water level is higher than the Reset water level and then perform the Fast time down test. 1. Activate the Service Mode in advance. - Beginning of Drain Session 2. To forward the program to the next cycle stage, - Beginning of Spin Session (Here, it checks the water level. So, if it is over the reset level, it carries out draining before the spinning.) press the Temp key. - Beginning of Fill Session - Beginning of Bleach Fill - Beginning of Fabric Softener Fill - Every 3 minutes during Wash and Rinse Tumble Session

44 4. Test Mode & Error Check Fast Time Down Test Mode

45 4. Test Mode & Error Check Board Input Test Mode Definition of Board Input Test Mode: - Board Input Test Mode is to displays a specified input after a key press. How to Enter: - To enter the Board Input Test Mode, press the Extra Rinse key during Service Mode. Board Input Test Mode: 1. Activate the Service Mode first. 2. Press the key to start Board Input Test. 3. Turn the Jog-Dial so that the normal course LED is turned on, and The Water Temperature will be displayed in Celsius. 4. Turn the Jog-Dial so that the LED is turned on, The Water Temperature will be displayed in Fahrenheit. 5. Turn the Jog-Dial so that the LED is turned on, The door status will be displayed (OP if open, CL if closed). 6. Turn the Jog-Dial so that the LED is turned on, The Door Lock Switch status will be displayed (UL if unlocked, LO if locked).

46 4. Test Mode & Error Check Diagnostic Code Check Mode Definition of Diagnostic Code Check Mode: - Diagnostic Code Check Mode is to bring up the stored diagnostic codes (refere codes for service technicians). How to Enter: - To enter the Diagnostic Code Check Mode with code d flashing, press the Spin key during Service Mode.

47 4. Test Mode & Error Check Diagnostic Code Check Mode Board Input Test Mode: 1. Activate the Service Mode first. 2. Press the Spin key key to start Diagnostic Code Check Mode with Code d flashing. 3. To cycle through the diagnostic codes (d1,d2,d3~d9), turn the Rotary Cycle Selector in one direction (either Clockwise or Counterclockwise). 4. Now, when turning the Rotary Selector Key in the same direction, it shows diagnostic codes from the latest (d1). 5. When turning it in the opposite direction, it shows the diagnostic codes in the reverse order. Ex) When it stops at d5 and turns backward, it shows from d4 down to d. Refer to Diagnostic Code.

48 4. Test Mode & Error Check Demo Mode How to Enter: To enter the Demo Mode, Press Delay Start + Soil Level Key for 5 Sec While a cycle is not running.

49 4. Test Mode & Error Check 4-2. Diagnostic Code & Corrective Action NO Error Code 1 nd 2 LO 3 nf Description The water level fails to drop below the Reset Water Level within 15 minutes. Door fails to unlock after 7 attempts. When the filling continues for more than 40 minutes or there is no change of water level for 6 minutes. Corrective Action Go to Will Not Drain Troubleshooting Section. Go to Will Not Unlock Troubleshooting Section. Go to No Water Fill Troubleshooting Section.

50 4. Test Mode & Error Check 4-2. Diagnostic Code & Corrective Action NO Error Code 4 FL 5 LE Description Door fails to lock after 7 attempts. A water level lower than the Reset water level is detected for 5 seconds during the Wash/Rinse cycle. Corrective Action Go to Will Not Lock Troubleshooting Section. Go to No Water Fill Troubleshooting Section. Water Level Sensor Trouble. (When the input signal from the water level sensor is out of range, the unit 6 1E will send out beeping sounds and halts the cycle.) Go to No Water Fill Troubleshooting Section.

51 4. Test Mode & Error Check 4-2. Diagnostic Code & Corrective Action NO 7 Error Code OE Description Corrective Action A fault is detected in the water level sensor. Data (frequency) shows the water level is at or above the First check to see that all of water valves are not overflow water level. (When this condition is detected, stuck. If water valves are OK, check water level. the machine will automatically starts draining water until the water level falls below the reset water level) 8 9 dc Unbalance or cabinet bump is detected during final spin, which prevents the drum from spinning over 150 rpm. (Never exceeds 150 RPM due to unbalanced Go to Wet Clothes Troubleshooting Section. load) E2 Jammed Key.(When key input signals are coming out for more than 30 seconds, it is regarded as a jam.) Check all of keys. If A key is sensed to be pressed, all keys will do not respond.

52 4. Test Mode & Error Check 4-2. Diagnostic Code & Corrective Action NO Error Code Description Corrective Action ds Door is detected as open while it is trying to lock the Go to Quick Test Mode and then do Door door. Lock/Unlock Test te Abnormal high/low temperature or resistance (Thermal sensor or PBA resistance). Go to Board Input Test and check Water Temperature. Check loose or pinched wires. Replace PCB or thermistor. MICOM is attempting to drive the motor but is not getting any response signals from the hall sensor. Visual check shows motor is not running. (Locked, Defective Hall Sensor or Overload) Evaluate wire harness for loose or unhooked connections. Go to Quick Test Mode and test Motor. 3E

53 4. Test Mode & Error Check 4-2. Diagnostic Code & Corrective Action NO Error Code Sr Hr nf1 Description System Relay (Main Relay) Failure. (PCB does not notice the relay operation when there should be.) Heater Relay Failure (No Heater Relay Check Signal) The hot/cold water hose connection is not correct. Corrective Action Replace PCB. Replace PCB Please connect the hot/cold water hose connection correctly.

54 4. Test Mode & Error Check 4-2. Diagnostic Code & Corrective Action NO Error Code 16 2E Description Voltage for motor control bus is over or under specified limit. Corrective Action Replace PCB Suds is detected during the washing session. ( SUdS is not an error. If the washer is in suds Guide a user to reduce amount of detergent usage. period, SUdS will light up instead of remaining time.) 17 suds 18 AE Communication error between SUB PBA and MAIN Check Main PBA, SUB PBA & Wire-harness. PBA Replace PCB 19 SF System Error Replace PCB

55 5.SVC Information 5-1. Troubleshooting Problem Will Not Start What To Do Plug the unit into the wall outlet. Check for proper voltage. Check fuse or reset circuit breaker. Push any key to turn on the washer and press the Start/Pause key to run the washer. Close door and push the Start/Pause key to run the washer. Check if washer is in a pause, soak or suds process. Wait briefly and it may start. (If the washer is in suds period, Suds will light up instead of remaining time.) Check for restricted drain system. (If there is electrical problem in drain system, nd error will occur after 15 minutes.) Check Water Supply. Check the line or water valve screen filter. Check if PCB connectors are assembled properly. Check if CN2 terminals on PCB are in good condition. (Refer to PCB Connector Check.) Replace PCB.

56 5.SVC Information 5-1. Troubleshooting Problem Leaking What To Do Make sure inlet hose connections are not leaking. Check for rubber gasket damage due to over tightening. Check standpipe for leak. Wrap a dry rag around the standpipe opening. If rag becomes wet, leak is fault of home plumbing. Be sure the standpipe is capable of accepting the flow of water from the washer. Make sure end of drain hose is correctly inserted and secured to drain standpipe. Check internal hose connections (fill, drain systems, dispenser hoses & clamps). Check rubber boot. Remove, reposition and reinstall, if necessary. Check for possible kinked dispenser to outer tub hose. Hot water pressurization may force door open.

57 5.SVC Information 5-1. Troubleshooting Problem What To Do No Tumble Start normal cycle with an empty machine and allow a fill to check tumble. Perform Quick Spin Test. (Before test, make sure that the tumbler is empty.) Check for loose connections at Machine Control Board, Pressure Switch, Motor, Tach Harness and Motor Control. (Refer to the component testing procedure) Check motor windings resistance. CN5 pins 1 & 3 = 11.6ohms ±7%, Pins 1 & 2 = 11.6ohms ±7%, Pins 2 & 3 = 11.6 ohms ±7% Faulty Main Control Board. Faulty motor.

58 5.SVC Information 5-1. Troubleshooting Problem Will Not Spin What To Do Make sure to close the door completely. Check for water left inside the washer. If so, go to Will Not Drain. Perform Quick Test Mode or Quick Spin Test. Does the washer spin? (Before the test, empty the unit inside.) If it doesn t tumble after the above, change PCB. When the problem persists, change the motor. Perform Quick Test Mode or Quick Spin Test. Does the washer spin? If it does, Check Possible unbalanced load scenario in normal mode. Check for loose connections at PCB, Water Level Sensor, Motor, Hall Sensor Wire Harness. (CN7,CN5,CN6) (Refer to the Component Testing Procedure.) Check motor windings resistance. (CN5 Pin1&3 = 11.6 ohms (at ±7% 20 C/68 F), Pin1&2 = 11.6ohms (at ±7% 20 C), Pin2&3 = 11.6 ohms (at ±7% 20 C))

59 5.SVC Information 5-1. Troubleshooting Problem What To Do No water Fill Perform Quick Test Mode. Check all of Water Valves visually. (Pre Wash Valve, Cold Water Valve, Bleach Water Valve, Softener dispenses using Cold & Bleach Water Valve, and Hot Water Valve.) Check if water taps are turned on fully. Check Water Valves and Water Level Sensor (Refer to PCB Connector Check) Check if there is any kink in inlet hoses. Check if inlet screens are clogged up. Check if water has enough pressure. If so, find out its contributors. Check if there is any frozen area in the unit (Drain Hose, etc) Measure the resistance of Water Valve Coil. (It should read 1.18K ohms. Check Pin#1 of CN2 and PIN#1,2,7,8,9 of CN3) Check Pressure S/W and PCB for loose connections. (Refer to PCB Connector Check.)

60 5.SVC Information 5-1. Troubleshooting Problem What To Do Tub Full of Suds Go to Will Not Drain and Will Not Spin and check the draining. Check PCB and Drain Pump for any loose wire connection. Perform Quick Test Mode or Board Output Test to drain. Use HE (High-Efficiency) or low sudsing detergent specially formulated for front load washers. Reduce the amount of detergent for that specific load size and soil level. Keep in mind that towel creates more suds generally. Reduce the amount of detergent when water is soft, or laundry is small or lightly soiled. Do one more washing cycle with cold water and a table spoon of salt without detergent.

61 5.SVC Information 5-1. Troubleshooting Problem Wet Clothes What To Do Unbalance due to not enough load. Put additional load. Due to excessive suds by using general detergent. Use HE (High-Efficiency) or reduce its quantity. Low Spin Speed or Drain Only was selected. Go to Will Not Spin.

62 5.SVC Information 5-1. Troubleshooting Problem What To Do Will Not Lock Door is not aligned or closed properly. Perform Quick Test Mode. Check Door Lock. Check the output voltage of Door Lock Coil.If it reads 120V, change Door Lock Switch, and if not, change PCB. (Refer to PCB Connector Check.) Read Lock Switch and PCB (CN3). (Refer to PCB Connector Check.) Try Door Lock and check for 120V to Door Lock Connector. If 120V present, change Main Control Board and if not, change Door Lock switch.

63 5.SVC Information 5-1. Troubleshooting Problem Will Not Unlock What To Do Check if the door is being pushed out, which may keep it from unlocking. Door locks itself when the water level is too high. Opening door will result in water draining from door opening. Check the following with Board Input Test Mode. Water Level (frequency): Over KHz. If so, refer to Will Not Drain. Temperature (Inside Drum): Higher than 60ºC/140ºF. If so, wait until it drops. When everything is normal, check PCB connectors and Door Lock Switch. Drain manually after removing the plastic drain hose holder. Display shows LO. Turn off and on the unit. If LO keeps illuminating, check PCB and Door Lock Switch. Read Lock Switch and PCB (CN2 & CN3). (Refer to PCB Connector Check.) Perform Quick Test Mode. Check Door Lock. Check the output voltage of Door Lock Coil. If it reads 120V, change Door Lock Switch, and if not, change PCB. (Refer to PCB Connector Check.)

64 5.SVC Information 5-1. Troubleshooting Problem What To Do No Key Operation Option and Function buttons respond differently according to each cycle. Child Lock is being activated. To exit, hold down Soil Level Key and Signal Key simultaneously until it sends out a beeping sound. When End illuminates on the display, only Power button works. Press Power button and make new cycle selections.

65 5.SVC Information 5-1. Troubleshooting Problem Will Not Drain What To Do Check for any kink on the drain hose. If any, straight it out. Check for any restriction in the drain hose. Close the door and press the Start/Pause Button. For safety reasons, the washer does not tumble or spin with the door open. When it is freezing outside, check if it is frozen inside the drain hose. Check if the water level signal input is correct. Go to Board Input Test Mode. Go to Quick Test Mode and do Drain Pump Test. Check if there is any twist in the hose (the one between Tub and Drain Pump). Check if it reads AC 120V at the pump when a spin cycle is selected. Read the winding resistance of the pump motor. (14.2±7% Ohms) Check the pump at CN3(PIN3) on PCB. It should read AC 110~120V. (Refer to PCB Connector Check)

66 5.SVC Information 5-1. Troubleshooting Problem What To Do Wrong Water Temperature Check if both of the water taps are fully open. Make sure the domestic water heater is set to deliver water lower than 120 F (49 C) hot water at the tap. Also check water heater capacity and recovery rate. If the water heater is located far from the washer, screw out the hot water tap and let its water pass until you get hot water. Too Hot/Too Cold: Reduced amount of water is supplied while PCB controls the influx to regulate the actual temperature of the water in the tub. This may appear to be significantly hotter/colder than expected. Check if the temperature selection is correct. Disconnect inlet hoses from the Water Valve and remove any residue in the inlet screens.

67 5.SVC Information 5-1. Troubleshooting Problem What To Do Noisy and/or Vibration/Walking Check if the washer is leveled and the lock nuts are tightened up on the bottom plate. Check if all of the shipping bolts and spacers are removed from the back panel. Check if load is big enough and there is no unbalance. If there is not enough load, put in a few towels to balance it. Check if the motor is fastened enough. Remove various trouble contributors (such as dust coat on the floor).

68 5.SVC Information 5-1. Troubleshooting Problem Rubber Feet Leaving Marks on Floor What To Do Use a pencil eraser to remove mark. Walk washer into location, do not drag.

69 5.SVC Information 5-1. Troubleshooting Problem Additive Cups Full of Water What To Do Small amount of water in bottom of additive cups is normal. Remove and wash Dispenser Tray, removable Cup, and Rinse Cap. Level washer.

70 5.SVC Information 5-1. Troubleshooting Problem Buttons do not Respond What To Do Option and Function buttons respond differently according to each cycle. Child Lock feature has been selected. To disable feature press and hold Temp and Spin simultaneously until a beep is heard. When display shows End, only the Power button will function. Press Power and make new cycle selections.

71 5.Reference Information 5-2. PCB Connector Check CN5 ① ① CN1 CN8 ④ ⑥ ③ ④ ① CN2 ② ① ② ③ ① RY2 R1 ③ ① RY1

72 5.Reference Information 5-2. PCB Connector Check Hall Sensor Check Check Voltage at Pin #4 and #3 of CN8 Tester Check = DC0.6V or 1.3V Check Voltage at Pin #4 and #2 of CN8 Tester Check = DC0.6V or 1.3V Motor Check Resistance at Pin #1 of CN1 and R1-GND = 280 or 470 Resistance at Pin #2 of CN1 and R1-GND = 280 or 470 Resistance at Pin #3 of CN1 and R1-GND = 280 or 470 Door Lock Check Check Voltage at Pin #1 of CN2 and Pin #6 of CN5 When Door Lock = AC 120V Drain Motor Check Check Voltage at Pin #1 of CN2 and Pin #4 of CN5 When Drain Pum p operates = AC 120V Water Valve Check Check Voltage at Pin #1 of CN2 and Pin #1,2,3 of CN5 When Drain Pum p operates = AC 120V Heater Relay Check Check Voltage at Pin #1 of CN2 and Pin #1 of RY2 When Heater Relay operates = AC 120V AC Power Check Check Voltage at Pin #1 and #3 of CN2 Check Voltage at Pin #1 of CN2 and Pin #1 of RY1 Tester Check = AC 120V

73 5.Reference Information 5-3. Wiring Diagram WF210

74 5.Reference Information 5-3. Wiring Diagram WF220

75 5.Reference Information 5-4. Components Check Door Lock S/W Water Level Sensor Water Valve 1.Check the door switch 1.Check the water level sensor resistance. 1. Check the resistance for the frequency. 2.Check the resistance after the water supply valve. 2.Check it after the water level power is off. Resistance : 1.0k to 1.2kΩ sensor and the connector 3.The resistance across No.1 2. Check whether there is foreign are connected. and No.3 of the Door Lock material in the water supply valve 3.Frequency: Approx khz Switch must be diaphragm. with no load. approximately 40 to 57Ω.

76 5.Reference Information 5-4. Components Check Drain Motor Drum Motor Resistance : Approximately 174Ω between the terminals for the Water Supply Valve. Plug out the connector and read resistances at any two of the three terminals on Motor : Should be 15 Ω

77 5.Reference Information 5-5. Schematic Diagram (Main PCB)

78 5.Reference Information 5-5. Schematic Diagram (Sub PCB)

79 5.Reference Information 5-6. Q & A Q. How long does it take for the door to unlock? A. It takes approximately 2-3 seconds for the door to unlock. Q. The cycle is complete and End is displayed. How do I set another cycle? A. When End is displayed, the Power button should be pressed or door should be opened before selecting another cycle. The display will show End until washer is turned off. To turn off washer, the Power button should be pressed or the door should be opened Q. What should I do when Information Code ( dc ) lights up? A. When the Information Code is displayed, press the Start/Pause dial and then restart the cycle. For more information, refer to the Owner s Manual Q. There is a small amount of water left in Detergent Drawer after the load is complete. Is this normal? A. It is normal for a small amount of water remaining in Detergent Drawer after it completes washing. Bleach is usually flushed out into the tub at the beginning of the washing. Also, its compartment is washed again during the following rinse cycle, removing any remnants.

80 5.Reference Information 5-6. Q & A Q. When I went back to my washer, it was turned off. What happened? A. Power button may have been accidentally bumped or pushed. Reset the cycle and start the washer. Make sure the unit is plugged into a live electrical outlet. Check house fuse or circuit breaker. Q. The washer door gets locked after a power failure. How can I open it? A. If the power fails while the door is locked, the door will remain locked until the power comes back on. If the power comes back on while the door is still locked, the cycle will resume where it left off. If the door is unlocked, PF will display and the washer will pause. Press Power Off and restart the cycle. Q. The washer door does not unlock when there is water in the tub. How can I open it? A. The water must be drained from the tub for the door to be opened. Set the rotary dial to Spin Only and press the Start/Pause dial. The door will open 2-3 seconds after the Spin or Drain cycle is completed.

81 6.Disassembly & Reassembly Part Disassembling and Repairing the MOTOR Figure Description

82 6.Disassembly & Reassembly Part Disassembling and Repairing the COVER-TOP & PANELCONTROL Figure Description

83 6.Disassembly & Reassembly Part Disassembling and Repairing the COVER-TOP & PANELCONTROL Figure Description

84 6.Disassembly & Reassembly Part Disassembling and Repairing the DOOR Figure Description

85 6.Disassembly & Reassembly Part Disassembling and Repairing the FRAME-FRONT Figure Description

86 6.Disassembly & Reassembly Part Disassembling and Repairing the FRAME-FRONT Figure Description

87 6.Disassembly & Reassembly Part Disassembling and Repairing the VALVE Figure Description

88 6.Disassembly & Reassembly Part Disassembling and Repairing the WATER LEVEL SENSOR Figure Description

89 6.Disassembly & Reassembly Part Disassembling and Repairing the PUMP MOTOR Figure Description

90 6.Disassembly & Reassembly Part Disassembling and Repairing the TUB Figure Description

91 6.Disassembly & Reassembly Part Disassembling and Repairing the TUB Figure Description

92 6.Disassembly & Reassembly Part Disassembling and Repairing the DRUM Figure Description

93 THANK YOU