Single Lever Pull-Out Kitchen Faucet

Transcription

1 INSTALLATION MANUAL Single Lever Pull-Out Kitchen Faucet KPF I toll free: I Kraus USA Inc. I REV. August 16, 2016

2 Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at and one of our representatives will be happy to help. For more information about Kraus products, please visit: In order to activate your warranty and get faster access to customer support, please register your new Kraus product at: Sincerely, Kraus USA Customer Service 1

3 PRIOR TO INSTALLATION Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at for a replacement Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber s putty, or silicone Place bucket under angle stops. Turn on to flush any debris prior to installing new plumbing. Shut off angle stops Pre-drilled hole size requirement: 1-3/8 Max countertop thickness without deck plate: 1-3/8 For technical assistance or replacement parts, please contact Kraus Customer Service and one of our representatives will be happy to help: Toll-Free: or Customerservice@kraususa.com Tools Required Adjustable Wrench Phillips Screwdriver Safety Goggles Bucket Silicone Sealant 2

4 Diagram and Parts List 10 G 9F 8E 11 H A1 12 I 13 J 2B C1 3 C2 4 C3 5 C4 6 D7 A. Faucet Body B. Base C. Mounting Hardware Assembly C1 Rubber Washer C2 Metal Washer C3 Mounting Nut C4 Mounting Screws D. Weight E. Spray Head F. Spray Hose G. Spring H. Sprayer Holder I. Hot and Cold Waterlines J. Supply Hose 3

5 Faucet Dimensions 8 203mm 8-1/2 215mm Ø1-3/8 ~Ø1-1/2 Ø35mm~Ø38mm Hot Water Cold Water 4

6 Faucet Dimensions Max1-3/8 21-1/4 Max35mm 540mm 5

7 Faucet Installation Procedure Installation Method 1 Off 25 O Minimum distance 3.5 The minimum distance between the faucet hole and the wall should be 3.5 Installation Method 2 Less than 3.5 If the distance between the faucet hole and the wall is less than 3.5, position the faucet lever 30 degrees to 90 degrees off of the wall to allow for full operation 1 30 Ø35~Ø38 Ø1 3/8~Ø1 1/

8 Off 25 On 90 Step 1 Left Hot Water Right Cold Water Remove mounting screws hardware (6), mounting assembly (C) nut (5), metal washer (4), and rubber washer (3) from the faucet body (1) 1 A1 Ø35~Ø38 Ø1 3/8~Ø1 1/2 Step 2 2 C1 3 C2 4 C3 5 C A 2B Insert the faucet faucet body body (A) into (1) into hole the on deck hole or on sink the with deck base with (B) the attached. Attach mounting base o-ring (2). Install the rubber hardware assembly (C) washer (3), metal washer (4), mounting nut (5) and mounting screws (6) from underneath the sink 5 6 3C1 4C2 5C3 6C4 7

9 Step 3 After Adjust adjusting faucet body. the direction Secure of the mounting faucet hardware body (1), tighten (C) with the mounting wrench and nut Phillips (5) until head snug and screwdriver tighten the mounting screws (6) to the nut with a Philips head screwdriver C5 Step 4 Connect the spray spray hose hose (F) to (9) supply to the hose supply (J) and line tighten. and tighten Attach with weight (D) to lowest point a wrench until snug, then install vertically on spray hose (F) the weight (7) at the lowest point (horizontally) on the spray hose (12) J D7 F 8

10 Step 5 Step 5 F E G Hexagon Nut F A Hot Connect and hot and tighten cold waterlines (I) (12) to angle to the stops. angle Turn stops on and the tighten angle Water stops with and a wrench check until for leaks snug, (DO then NOT unscrew TURN spray FAUCET head ON) (8), hold the tip of the spray hose (9) and turn on the faucet to flush any debris Step 6 Cold Water ff Close 25 Open Left J Hot Water 90 Hot Water Cold Water Installer Tip Remove spray head (E) and turn Push faucet on for 60 second to flush any debris 9 KPF-1602.indd :39 PM

11 :39 PM Usage How to Operate the Handle Off 25 On 1. Pull the lever to the right to turn on the water. Push to the left to turn off 2. Pull the lever forward to increase hot water flow and push the lever back to Left Hot Water Right Cold Water increase the cold water flow r Off On Left Hot Water Right Cold Water 10

12 Replacement Parts 1. Spray Head 2. Plastic Sleeve 26a 26b Sprayer Holder 4. Spring 5. Spring End Cap 6. Set Screw 7. Cap 8. Set Screw 9. Lever 10. Set Screw 11. Handle 12. Cartridge Cover 13. Locking Nut 14. Cartridge 15. Protective Sleeve 16. Base 17. Base O-Ring 18. Rubber Washer 19. Metal Washer 20. Mounting Nut 21. Mounting Screw 22. Hose 23. Washer 24. Weight 25. Supply Hose 26. Hot & Cold Waterlines 11

13 Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under the handle (11) Water will not shut off completely Leaking between spray head (1) and the hose (22) Locking nut (13) has come loose Cartridge (14) may be defective Spray head (1) may be loose or washer (23) is not seated correctly in the hose connection Unscrew the lever (9) on the handle (11) by hand. Loosen set screw (10) with a hex wrench (2.5 mm). Remove the handle (11) and unscrew cartridge cover (12) by hand. Tighten locking nut (13) with an adjustable wrench Unscrew the lever (9) on the handle (11) by hand. Loosen set screw (10) with a hex wrench (2.5 mm). Remove the handle (11) and unscrew cartridge cover (12) by hand. Unscrew the locking nut (13) with an adjustable wrench. Remove ceramic disc cartridge (14). Check for cracks Tighten the spray head (1) by hand until snug. Make sure the washer (23) is seated correctly 12

14 Codes/Standards Applicable: NSF/ANSI Standard 61 certified by IAPMO NSF/ANSI Standard 372 certified by IAPMO GREEN LEAD FREE I APMOR&T Meets ASME A M/A gpm 6.6L/min maximum TM Water Efficiency HELP LINE Our customer service hours are Monday Friday, 9am 8pm EST. Be sure to visit our website at If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY Toll-free Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY Partnersupport@kraususa.com In requesting warranty service, please be ready to provide: 1. Proof of purchase. 2. A description of the problem. 13

15 Care & Maintenance *To keep the product clean & shining, follow the steps below: lose 25 Open 1. Rinse with clean water & dry with a soft cloth Do not clean with soaps, acid, polish, abrasives, or harsh cleaners 3. Do not use cloth with a coarse surface 4. Unscrew the aerator and clean when necessary Push Left *This Hot Water installation manual is subject to change without further notice. Download the Kraus Care & Maintenance Guide at:

16 REGISTER YOUR PRODUCT TODAY Receive Proof of Ownership Access Customer Care & Installation Help Get Exclusive Kraus Offers & Promotions Scan to Register Online or visit We re always looking for ways to improve. Please take a moment to share your experience. Visit to let us know what you think about your new Kraus product. Contact Us to Learn More / / customerservice@kraususa.com Like & Follow KrausUSA Download the Kraus Care & Maintenance Guide at: