KYROS WATER HEATER INSTRUCTION MANUAL. Assembly, installation, start-up and operating instructions

Transcription

1 KYROS INSTRUCTION MANUAL WATER HEATER Assembly, installation, start-up and operating instructions EN

2 Thank you. Many thanks for your confidence in our Rointe products. Before you start to use the low-consumption Kyros water heater we recommend that you read this manual carefully in order to use the product correctly with the maximum guaranteed results.

3 English ATTENTION: If you are the owner of a model bought in the UK or Éire, please refer ONLY to its manual as the especifications of the water heaters are different. INDEX OF CONTENTS 1. INSTALLATION Accessories Placement Location Water System installation Electrical Installation Safety USE DESCRIPTION OF THE KYROS WATER HEATER Description of the front panel Switch On and Off (Stand By) Select Temperature Lock the Control Panel Adjust Date and Time Main Menu ADVANCED FUNCTIONALITY FUZZY LOGIC ENERGY CONTROL MAINTENANCE CONDITION OF THE GUARANTEE DIMENSIONS AND TECHNICAL CHARACTERISTICS

4 KYROS 1. INTRODUCTION 1.1. Accessories The electric water heater, or boiler by accumulation under pressure, is provided with basic elements for its installation, such as: Insulating sockets. Safety valve. These accessories are included within the packaging Placement In order to fix the heater to the wall, you will have to use suitable rawlplugs, screws, or other fittings to support the weight of the heater when it is full Location It is essential that the heater is situated as near as possible to the place where hot water is required. In this way, water temperature loss in the pipework can be avoided. Leave a minimum space of 500 mm below where the pipes exit the heater to allow access for maintenance and repair and any necessary future maintenance operations 150 mm 100 mm 100 mm H 540 mm C 4

5 Do not install the heater horizontally with the wall supports horizontal or over the floor Water system installation WARNING TO THE INSTALLER: the insulating sockets provided with the heater must be placed on the entrance and exit pipes to eliminate the risk of galvanic pairs as teflon is used in the thread of the pipes. A- The heater MUST be installed with the security fitting that comes with it. No water system accessory may be placed between the security fitting and the cold water pipe (stop cock, anti-return, etc). The security fitting drainage outlet MUST be connected to a water drainage pipe that has to have a diameter that is at least equal to the diameter of the pipe connected to the boiler, with a continuous inclination, open to the atmosphere and with a minimum distance of 20 mm. During the warm-up time the water expands producing a drip (approximately 3% of its capacity during each heating cycle). This is not a cause for concern because it is a normal phenomenon. Please ensure that the water drainage conduct pipe is protected from frost. To drain the heater, lift the handle of the security fitting. It is also necessary for this handle to be periodically checked to avoid blockage by, for example: mud deposits, limescale deposits, etc. B- When the pressure of the network is higher than 5 bars, it is necessary to install a pressure reducer as near as possible to the meter. 5

6 KYROS 1.5. Electrical installation The appliance requires a single-phase 230 V supply. It is necessary to check carefully that the supply voltage agrees with the required voltage of the appliance. The heater does not need installation requirements outside the norm, therefore it is suitable for installation in accordance with the Electrotechnical Low Voltage Regulations. The power supply will have to be wired through a omnipolar interrupter, circuit breaker or contactor. The installation must be protected with fuses of a rating that corresponds with the intensity absorbed. The socket must be placed in such a way that when the heater is installed the plug is accessible. An earth connection must be included throughout the electrical installation. In order to ensure this connection the plug comes provided with the relevant contact. It is important that the style of any other plug used is the same type as the one provided with the appliance. The electrical system of the premises or house must be checked to ensure that it is equipped with an EARTH wire. This appliance complies with the regulations on radio-electric disturbances and interferences. NOTE: All maintenance and replacement of the fittings is prohibited (including the feed cable), unless it is authorised by the Technical Assistance Department. 6

7 Wiring diagram - Kyros water heater. Assembly schematic - Kyros water heater. 7

8 KYROS 1.6. Safety This water heater can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are supervised or have been given instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children without supervision. Children must be supervised at all times to ensure that they do not play with the product. 2. USE 2.1. Operation Filling. Once the heater has been installed, open the stop cock. Then open the hot water taps. When the water begins to come out of them the heater is full. Close the taps and check thoroughly that there are no leaks in the installation. Do not connect the heater to the mains supply before ensuring that it is full of water. Electrical connection. Plug in the heater, switch on and leave the appliance connected to the electricity supply. Once a certain amount of hot water has been used, the thermostat switches the heating element back on. Draining. In prolonged periods without use, and if there is risk of frosts in the premises where it is installed, the heater must be drained. It is possible to do this using the safety valve. In all cases: Cut the current 8

9 Close the tap where water enters the Installation. Drain through the safety group using the lever. 3. DESCRIPTION OF THE KYROS WATER HEATER 9

10 KYROS 3.1. Description of the front panel ICON MENU INDICATION On / Off - Accept Decrease temperature - Move left Increase temperature - Move right Access/Back to menu - Move up Manual / Automatic - Move down TFT Display

11 NUM. INDICATION 1 Hours programmed - AUTO 2 Days of the week 3 Time 4 Selected temperature 5 Locking the control panel 6 Manual / Automatic / Pilot wire functions 7 Comfort / Economy / Anti-frost modes 8 Heating Element in operation 9 Consumption behaviour indicator ICON DESCRIPTION Consumption indicator green / yellow / red Water heater heating element on Comfort Mode activated Eco mode activated Anti-frost mode activated Automatic mode activated Manual mode activated Pilot Wire Control mode activated Not available in Spain. Only upon demand 11

12 KYROS Automatic function activated in USER mode Manual function activated in USER mode Pilot wire control function on when USER function is working. Not available in Spain. Only upon demand Locked through radiator control panel. Remote lock. Locked through IR remote control. 3.2 Switch On and Off (Stand-by) The Kyros technology water heater is switched on or off using the button. The following welcome appears on the TFT screen when the water heater is switched on. The main temperature screen will appear after 5 seconds. If you press the button again when the water heater is switched on it will revert to stand-by mode and the words Stand-By will appear. 5 seconds later and the Rointe logo will appear. 12

13 3.3 Temperature selection You can change the desired temperature using the keys or. If the temperature of the room is less than is desired then the water heater will begin to heat up and the symbol will appear. 3.4 Locking the control panel You can lock the product from the actual control panel of the water heater or the Air Control remote control. On the product control panel you can lock the keypad by pressing and holding down the and buttons at the same time for 3 seconds. The locked icon will appear. When you press any button the image on the right will appear on the screen. You can unlock the product again by pressing and holding down the and buttons for 3 seconds. If we lock the product via the application or remote control then the remote locked icon will appear on the screen. When you press any button on the water heater control panel, the image on the right will appear on the screen. If the product is locked in this way, you can only unlock the water heater via the Air Control remote control. 13

14 KYROS 3.5 Adjusting time and date It is possible to change the time on the water heater from the control panel. Here we explain how to change the time from the water heater control panel. MENU Press the menu button to access the main menu. Select the sub-menu by using the and buttons then press to access. In the configuration sub-menu, use the and buttons to select the clock then press to access. Clear Memory By pressing the button, the hours, minutes and days will flash depending on the number of times the button is pressed (1 for hours, 2 for minutes and 3 for the day of the week). We can change any of these by pressing the or buttons. To confirm, press the button. To exit the time/day mode wait 30 seconds or press the after selecting the day of the week. button 14

15 3.6 Main menu MENU Press the button to access the main menu of your Kyros water heater. You can move between the different options on the menu by pressing the and buttons. The sub-menu which you have selected will be highlighted with a frame. The following icons allow you to access different sub-menus which we will now explain: Configuration Sub-Menu Energy Sub-Menu Balance Function Programming Sub-Menu Configuration Sub-menu The configuration sub-menu consists of 4 technical parameters of the product. To access this menu, press on the main menu screen. The screen on the right will appear and we can move between the various options of the sub-menu by using the and buttons. We can access the various sub-menus, which we can now explain, using the following icons: Clear Memory Clear Memory Screen backlight Clear memory Language Adjust day / time 15

16 KYROS Screen backlight function This function allows you to change the brightness of the screen in the STAND-BY and BACKLIGHT (ON) modes. We can change between the 2 MENU modes by using the and buttons. We can increase or decrease the brightness by using the and buttons. The cursor shows the intensity of the light within the range. Press the button to confirm and to exit. Language You can select the language you wish using this function. Select the language you wish by MENU pressing the and buttons. Press the button to confirm the language highlighted. LANGUAGE ENGLISH FRANÇAIS ESPAÑOL PORTUGUÊS Adjust date / time This function allows you to change the hour, minutes and day of the week on the product control panel. To adjust the time/date please revert to section

17 3.6.2 Energy Sub-menu The Energy Sub-menu allows access to the functions relating to the energy management of the product. Select the icon from the main menu by using the and buttons. Press to access this screen. The following icons allow you to access distinct sub-menus: Water heating progress Anti legionnaire s disease Effective power function Information Water heating progress We can see the progress of the water heating process towards the userestablished target temperature. In this image, 100% of the water contained in the water heater is at the user-defined target temperature. When the water in the tank is not yet at the user-defined target temperature indicated on the TFT screen, a percentage value is displayed. This represents the heating progress towards this target temperature. 17

18 KYROS Anti legionnaire s disease The water heater is automatically set to over 60ºC for at least one hour once a week. Whilst this mode is active, you will see the following screen. Within the legionella function you can choose the time period in days for the activation of the legionella function. (By default this period is 7 days) ANTILEGIONAIRE S DISEASE FUNCTION PERIOD (DAYS) 7 Effective Power Function This function shows the working time and total time that the product has been connected on the main screen. The nominal and effective power will appear on the screen after 6 seconds without pushing any buttons The effective power is the actual consumption of our product during the total time it is switched on. 18

19 Information This option shows the software version, the release date and the nominal power of the product. Select the icon by using the and buttons, then press the button to confirm. To MENU exit from the information screen, press. POWER 2400W Balance Sub-menu The balance sub-menu forces the water heater to work in manual mode at a constant 19ºC. Select the icon from the main menu using the and buttons. Press the button to confirm. By pressing this button the water heater will return to the main screen with a set temperature of 55ºC and the Manual icon will appear Programming sub-menu In this section we will explain the aspects of the water heater in relation to how they work in their various functions and modes. 19

20 KYROS The programming sub-menu provides access to the functions related to programming the product. Select the icon from the main menu. The icons shown below allow access to the distinct sub-menus which we will describe later: / Manual / Automatic Function Start Programming User Function Pilot Wire Mode (Only upon demand) What are the manual, automatic and pilot wire modes? Manual Mode This mode allows you to change between comfort, eco and anti-frost modes changing the temperature as described in section 3.3. Automatic Mode This mode activates the programming which has been set in the water heater. Pilot Wire Mode Not available in Spain. Only upon demand This mode allows you to control the water heater via a central control. 20

21 What are the comfort, Eco and Anti-Frost modes? These modes represent different ranges of temperatures available within the products. Icon Mode Temperature Range Comfort From 55ºC to 73ºC Eco From 40ºC to 54.5ºC Anti-Frost 7ºC Manual/Automatic Function Press the button to change between the Manual and Automatic modes. On the main screen the symbol will appear in Automatic mode and the symbol will appear in Manual mode. The Automatic Mode will activate the programming which you have already set in the product. 21

22 KYROS Start Programming To start programming, use the and buttons to choose the icon and confirm by pressing the button. We must be in AUTOMATIC MODE. A screen for selecting one of the four initial programming or self programming With keys and is exchanged between presets and programming custom home. With confirmed with key and screen appears with all 4 presets. 1 Select the COMFORT temperature Use the and keys to select the COMFORT temperature, between 55ºC and 73ºC. The symbol and the temperature will flash. Once selected, press to confirm. 2 Select the ECO temperature Continue and select the ECO temperature, between 40ºC and 54.5ºC. The symbol and the temperature will flash. Press to confirm 22

23 3 Select DAYS After pressing the button, the days of the week will flash showing the days as Day1, Day 2 etc. We can use the and buttons to go forwards or backwards through the days. Press the button to select the day or days which you wish to program with the same programming. 4 Asign mode to each HOUR To access the hourly programming of the chosen days press until you pass day number 7. You can move back and forward between the hours by using the and buttons. The hours are shown as 0h, 1h, 2h 12h By using the button you can chose between the COMFORT, ECO and OFF modes. Once the hours of the selected days have been programmed, press MENU or wait 30 seconds without touching any button. You can program day by day or you can program several days at the same time. User Function To access the User Function, use the and buttons to select the icon and confirm by pressing. 23

24 KYROS USER Function This allows the user to establish a limited working temperature range (maximum and minimum temperature). By way of a 4 digit code you can access a menu where you can activate or deactivate this function, change the password and fix a maximum and minimum temperature range for the product When the product is working with this function one of the following symbols will appear on the main screen depending on whether it is in Automatic mode, Manual mode or Pilot Wire mode. Enter the PIN to access. The default PIN number is Select the numbers by using the and buttons and confirm by pressing. Press OK to access. If the pin number is wrong then the words INCORRECT PIN will appear on the screen. INSERT PIN CANCEL 0 OK INCORRECT PIN 24

25 When the PIN number has been entered correctly the main screen of the basic configuration will appear. The following icons allow access to the various sub-menus which we will now describe: Activate/ Deactivate Function Change Password Maximum Temperature Limit Minimum Temperature Limit Activate function Allows you to activate or deactivate the USER function. Select ON to activate or OFF to MENU deactivate the function by using the and buttons. Once the chosen mode has been selected, press to select and exit. USER FUNCTION ON OFF The icon or will appear at the top of the screen depending whether it is on Automatic mode or Manual mode. If the product is in Pilot Wire Mode then the icon will appear. 25

26 KYROS Change the PIN code You can change the access PIN code for this feature. MENU Use the,, and introduce the current PIN code. buttons. To To confirm select OK. The screen will show PIN CHANGED. NEW PIN CANCEL 0 OK PIN CHANGED Maximum temperature This allows you to set the maximum working temperature of the water heater. Using the and buttons you can increase or reduce the temperature between 55ºC and 73ºC. Press to exit once the desired temperature has been chosen. UPPER TEMPERATURE LIMIT 65.0ºC Minimum temperature This allows you to set the minimum working temperature of the water heater. Using the and buttons you can increase or reduce the temperature between 40ºC and 54.5ºC. Press to exit once the desired temperature has been chosen. LOWER TEMPERATURE LIMIT 45.0ºC To exit, press the MENU button or wait 30 seconds. 26

27 Pilot Wire Function Not available in Spain. Only upon demand Activate or deactivate the Pilot Wire Control function. Select ON to activate or OFF to MENU deactivate by using the keys MENU and. Press to confirm and exit. The symbol will appear on the screen. PILOT WIRE ON OFF WARNING! The Pilot Wire function only allows you to control your heating via the pilot wire programmer. 4. ADVANCED FUNCTIONALITY 4.1. Anti Legionnaire s Disease Our Kyros is designed with safety in mind, and all the anti legionnaires disease regulations are complied with. The water heater is automatically set to over 60ºC for at least one hour once a week. As indicated at the section yoy can choose the time period in days for the activation of the legionella function.whilst this mode is active, you will see the following screen: 27

28 KYROS 4.2. Water Heating Progress As indicated at the section we can see the progress of the water heating process towards the user-established target temperature. In this image, 100% of the water contained in the water heater is at the user-defined target temperature. When the water in the tank is not yet at the userdefined target temperature indicated on the TFT screen, a percentage value is displayed. This represents the heating progress towards this target temperature. 5. FUZZY LOGIC ENERGY CONTROL This product includes Fuzzy Logic Energy Control technology to efficiently manage the energy consumption of the water heater. Fuzzy Logic Energy Control bases its operation on thousands of micropulses being sent to the heating elements to keep a stable water temperature with a consumption as low as posible. When the symbol replaces the, then the Optimizer Energy Plus technology is working. 6. SERVICING AND MAINTENANCE The heater does not need any special maintenance, except an annual inspection of the magnesium anode. In order to clean it rub with a soft cloth or damp sponge. Do not use abrasives or detergent. 28

29 The electric water heater guarantee is 7 YEARS for the water tank and 2 YEARS for the electronics from the date of purchase. If the water heater breaks down during this guarantee period the entire appliance will be replaced. In the Canary Islands, the water tank is guaranteed for 3 YEARS. In order to guarantee the life of the water heater, it is a requirement that the user agrees to an annual inspection of the magnesium anode to check for erosion. Where erosion is excessive, it should be replaced. Our guarantee will be applied with the express condition that the electrical heater has been well installed by QUALIFIED FITTERS and with the PROTECTIVE SOCKETS which are provided with the appliance and that there has been an initial inspection of the anode. Excessive heating by a possible failure of the thermostat is protected by the safety limiter that cuts the two phases and leaves the heater without electrical supply. Should this occur, call the Technical Assistance Department to arrange repair. IMPORTANT - Never remove the connections cover without first unplugging the heater from the mains. Cleaning should not be carried out by children without supervision. Children must be supervised at all times to ensure that they do not play with the product. THE MANUFACTURER reserves the right to modify the characteristics and specifications of the products without prior warning. 7. CONDITION OF THE GUARANTEE The Guarantee for ROINTE S heaters is a commercial guarantee that is offered by us in our capacity as manufacturer, in addition to and independently from the rights that you receive from the seller as a result of the purchase, which are regulated by the laws applicable in the title V of the Real Decreto Legislativo 1/2007, 16 of November, remaining independent to and compatible with those granted by the current commercial guarantee What does the Rointe heaters guarantee cover? The Guarantee for ROINTE s heaters that we offer as manufacturer covers, over a term of two years from the appliance delivery date the repairs made by ROINTE s Official Technical Assistance Service on any faults that exist at the time of the delivery of the heater. It will be understood that the appliance always conforms with and meets the following requisites: The guaranteed appliance will correspond to those that have been expressly destined by the manufacturer for sale and installation, following all the 29

30 KYROS 30 current and applicable regulations. It will comply with the description given by ROINTE in the catalogues, web, instruction and installation manuals. It will be suitable for use in a manner typically applied to appliances of the same type. It will offer the quality and expected performance of appliances of the same type. The failure of any of the above that occur within the first six months after the purchase invoice date, the warranty date, or the completed guarantee card date, is assumed, unless proved to the contrary, to have existed at the moment of delivery. After this period, up to the end of the two year period, it will be up to the user to prove that any appearance of failure to conform to the requisites existed at the time of the delivery of the apparatus. In addition, the guarantee covers during both years from the date of purchase the cost of those components that are replaced by Rointe s Official Technical Assistance Service. In addition the electric water heater is a guaranteed for 7 years from the date of purchase, provided that an annual inspection of the condition of the magnesium anode is made by the Official Technical Assistance Service and it is replaced when there is excessive erosion. Remember that while the heater is being repaired or replaced, the period during which you can excercise your rights with the seller, and those that are offered in addition by ROINTE s heater guarantee, will be temporarily suspended until the repaired or substitue heater is delivered, from which time the unused guarantee period will be available, with a minimum period of 6 months in all cases. EXCEPTIONS: The following cases state exceptions from the present guaranteed cover, for which all repairs will be charged to the user: Damage caused deliberately through negligence or wrong use of the water heater by the client or third parties. The failures produced by chance causes, strong forces (atmospheric or geologic phenomena) and generally the failures caused by elements that don t belong to the heater. Faults that result from an incorrect installation or lack of maintenance of the heater, made by a professional without the necessary qualification. Guidance can be found within the recommendations for installation and use as found in the installation manual and in the instruction booklet. Corrosion caused by direct exposure to salt water is excluded from the guarantee. When the product is installed no more than 200m from the coast the guarantee for damages caused by corrosion the period will be

31 reduced by 50%. Aesthetic wear and tear produced by use, the cleaning of limescale accumulation, revision and substitution of the magnesium anode as well as other operations of maintenance of the heater. All heaters must be installed in a way that allows access for our technicians. The user is responsible for any costs and organization required to provide access to the heaters for their repair and / or substitution. VERY IMPORTANT: in order to be covered by this guarantee, it is essential that the user can prove to the guarantor s Official Technical Assistance Department the date of purchase by means of the invoice or ticket emitted by the seller of the heater and the certificate of guarantee. In the case of heaters supplied in newly built premises, it is sufficient to prove the date of availability of the heater to the user. If your ROINTE radiator needs to be sent to the guarantee service, contact the dealer / installer where it was purchased. In the event of any problems, you can contact ROINTE on its TECHNICAL ASSISTANCE HELPLINE or us at support@rointe.co.uk Cancellation of the present guarantee This guarantee will be annulled and therefore without any effect, if the heater has been manipulated, modified or repaired by unauthorized people or technical services that are not official with regards to the brand. It will also be annulled if the heater is not correctly installed with security fittings and the suitable protective sockets. European Directive (WEEE) 2012/19/EU Under the European Directive 2012/19/EU on waste electrical and electronic equipment (WEEE), the apparatus cannot be disposed in the usual council bins and containers. They must be separated to optimize the recovery and recycling of all of the components and materials and reducing the impact to human health and the environment. The symbol of the container crossed out over a horizontal line marks all of ROINTE s products to remind the consumer of the obligation to separate them on disposal.the consumer should contact the local authority or original point of sale to learn more about the correct disposal of this product. 31

32 KYROS 8. DIMENSIONS AND TECHNICAL CHARACTERISTICS REFERENCE KWN050DHW2 KWN075DHW2 KWN100DHW2 KWN150DHW2 KWN200DHW2 CAPACITY (L) POWER (W) 230 V~ 1,600 2,000 2,000 2,000 2,400 HEATING ELEMENTS 2 x 800 W 2 x 1,000 W 2 x 1,000 W 2 x 1,000 W 2 x 1,200 W kw in 24h. THERMAL LOSS at 65 C PLACEMENT Vertical Vertical Vertical Vertical Vertical WATER INTAKE (inches) 1/2 1/2 1/2 3/4" 3/4" EMPTY WEIGHT (kg) A , ,070 DIMENSIONS (mm) B , ,120 C D E F G H I J K EAN CODE D K C H I B A G 32 J F E

33 Cut along the dotted line CERTIFICATE OF GUARANTEE In the event of detecting any defect in the product within the period of guarantee, you must fill in the following Guarantee Certificate and send it to us stamped together with a copy of the sales invoice via to support@rointe.co.uk or to the following postal address: INDUSTRIAS ROYAL TERMIC, S.L., C/E, Parcela 43, Santomera (Murcia, Spain). For new constructions, it is essential that you attach the Certificate of First Occupation. CERTIFICATE OF GUARANTEE REFERENCE: Nº SERIES: USER: HOME ADDRESS: TOWN: POSTCODE: PROVINCE: COUNTRY: TELEPHONE: SELLER S STAMP: PURCHASE DATE: NB: This certificate of Guarantee must be filled in out in full in order to obtain guarantee rights. The date of purchase and seller s stamp are compulsory. Please, attach a copy of your sales invoices. In addition, for new constructions include the Certificate of First Occupation.

34

35

36 ROINTE UK Catalyst House 720 Centennial Court, Centennial Park Elstree, Herts, WD6 3SY T F Technical Support T ROINTE ESPAÑA Y PORTUGAL P.I. Vicente Antolinos C/ E, parc. 43, Santomera Murcia, España T F Servicio de Atención Técnica T sat@rointe.com MKTN16V1 - EN