TECHNICAL MANUAL Installation, Operation and Maintenance Instructions

Transcription

1 TECHNICAL MANUAL Installation, Operation and Maintenance Instructions POT AND PAN WASHERS CA-3 DA-3 Insinger Machine Company 6245 State Road Philadelphia, PA Fax

2 Thank you for purchasing a quality Insinger product. In the space provided below please record the model, serial number and start-up date of this unit: Model: Serial Number: Start-Up Date: When referring to this equipment please have this information available. Each piece of equipment at Insinger is carefully tested before shipment for proper operation. If the need for service should arise please contact your local Authorized Insinger Service Company. To find your local authorized Service Company please visit our web site, or call Insinger at For proper activation of the Insinger Limited Warranty, a SureFire TM Start-up should be completed on your machine. Refer to the Introduction section in this manual for an explanation of Insinger s SureFire TM Start-up and Check-out Program. Please read the Insinger Limited Warranty and all installation and operation instructions carefully before attempting to install or operate your new Insinger product. To register your machine for warranty, or for answers to question concerning installation, operation, or service contact our Technical Service Department. TECHNICAL SERVICE CONTACTS Toll-Free Fax TABLE OF CONTENTS Part Technical Information Specification Sheets Introduction Definitions Safety Summary Warranty Part 2 Installation Instructions General Installation Instructions Installation Drawings Part 3 Operation Instructions Part 4 Cleaning Instructions Daily Cleaning Instructions Weekly Cleaning Instructions Part 5 Maintenance and Repair Procedures Maintenance Requirements Maintenance Procedures Troubleshooting Part 6 Replacement Parts & Assemblies Assembly Drawings with Parts Lists Part 7 Electrical Schematics and Parts Electrical Schematics Control Panel Layouts Web site service@insingermachine.com CA-3 & DA-3 Technical Manual

3 PART TECHNICAL INFORMATION Project Item Quantity CSI Approval Date CA-3 Pot and Pan Washer Automatic door type utensil washer with timed wash and rinse cycle Capacity " x 28" racks per hour or 50 bun/pans per hour or 00 steam table (2" thick) pans per hour Fully automatic operation with power on/off button Cycle starts when doors are closed Rinse pressure regulator Hold-Down Rack System for secure washing Rollers make getting large racks in and out easier CA-3 is available for corner operation Rollers make getting large racks in and out of the pot washer easier. STANDARD FEATURES Wash tank heat: electric, steam injection Pressure regulator Single point electrical connection Low water protection Door safety switches vent opening with adjustable damper Inspection door Vacuum breaker on all incoming water lines Capillary thermometer for wash and final rinse 304 stainless steel construction Stainless steel front panel Automatic fill Detergent connection provision Hold-down rack system Manual bypass selector switch Side-mounted control panel (NEMA 2) Simplified scrap screen design Interchangeable upper and lower spray arms Standard frame drip proof motor Rack assortment- general utility, bake sheet, basket Manifold clean-out brush SureFire Start-Up & Check-Out Service OPTIONS Stainless steel steam coil tank heat Steam booster Electric booster Security package Totally enclosed motor Pressure reduction valve and line strainer CA-3 The Hold-Down Rack System keeps pots and pans secure during washing, eliminating damage to ware and equipment. CA-3 & DA-3 Technical Manual

4 PART TECHNICAL INFORMATION CA-3 Pot and Pan Washer Capacity Per Hour Tank Capacity Motor Size Electric Usage (Electric booster must have 6 gallon holding tank) Steam Consumption at 20 psi Final Rinse Peak Flow at 20 psi min. Final Rinse Consumption at 20 psi min. Exhaust Requirements Peak Rate Drain Flow Shipping Weight Current Draw Amps 230//60 208/3/60 240/3/60 480/3/60 380/3/50 25 racks/50 sheet pans 3 gallons 5 hp 5 kw wash tank 9 kw booster 40º rise 24 kw booster 70º rise 40º rise 20 lbs./hr. tank 25 lbs./hr. booster average 238 lbs./hr. booster peak 70º rise 20 lbs./hr. tank 44 lbs./hr. booster average 47 lbs./hr. booster peak.2 gallons/minute 2.8 gallons/cycle 70 gallons/hour Steam N/A CFM 9 gallons/minute 800 lbs. Electric w/o booster N/A Note: Due to product improvement we reserve the right to change information and specifications without notice. SPECIFICATIONS CONSTRUCTION- Hood and tank constructed of 4 gauge 8-8 type 304 S/S. Hood unit of all welded seamless construction. S/S frame, legs and feet. All internal castings are non-corrosive lead free nickel alloy or bronze. DOORS- A front inspection/clean-out door and two simultaneously opening operating doors. Operating doors balanced by externally mounted springs. Extra large die formed 8-8 type 304 S/S doors ride in all S/S channels. A triple ply leading edge on the door channels made of S/S. PUMP- Centrifugal type packless pump with a brass petcock drain. Construction includes ceramic seal and a balanced cast impeller on a precision ground stainless steel shaft, extension or sleeve. All working parts mounted as an assembly and removable as a unit without disturbing pump housing. One 5 hp motor, standard horizontal C-face frame, drip proof, internally cooled with ball-bearing construction. CONTROLS- Side-mounted control cabinet, NEMA 2 rated, housing motor controls and overload protection, transformer, contactors and all dishwasher integral controls. All controls safe low voltage 24 VAC. SPRAY SYSTEM- Wash and rinse spray systems made of 8-8 type 304 S/S pipe threaded into cast hub assemblies. Upper and lower spray assemblies are interchangeable and are removable without the use of tools. WASH- 2 power spinning wash arms above and 2 power spinning wash arms below, each designed with 8 high pressure action cleansing holes. FINAL RINSE- 2 power spinning wash arms above and 2 power spinning rinse arms below, each designed with 3 nozzles. DRAIN- Drain valve externally controlled. Overflow assembly with skimmer cap is removable with the use of simple tools for drain line inspection. Heater is protected by low water level control. *Note: Exhaust requirements are for duct connections only. CA-3 & DA-3 Technical Manual

5 PART TECHNICAL INFORMATION Project Item Quantity CSI Approval Date DA-3 Pot and Pan Washer Automatic door type utensil washer with timed wash and rinse cycle Capacity x 28 racks per hour or 276 bun/pans per hour or 84 steam table (2 thick) pans per hour Fully automatic operation with power on/off button Cycle starts when doors are closed Rinse pressure regulator Hold-Down Rack System for secure washing Rollers make getting large racks in and out easier Rollers make getting large racks in and out of the pot washer easier. The Hold-Down Rack System keeps pots and pans secure during washing, eliminating damage to ware and equipment. STANDARD FEATURES Wash tank heat: electric or steam injection Pressure regulator Single point electrical connection Low water protection Door safety switches 2 vent openings with adjustable damper Inspection door Vacuum breaker on all incoming water lines Capillary thermometer for wash and final rinse 304 stainless steel construction Stainless steel front panel Automatic fill Detergent connection provision Hold-down rack system Rollers for track Manual bypass selector switch Side-mounted control panel (NEMA 2) Simplified scrap screen design Interchangeable upper and lower spray arms Standard frame drip proof motor Rack assortment- 2 general utility, 2 bake sheets, basket, counter pan Manifold clean-out brush SureFire Start-Up & Check-Out Service OPTIONS Stainless steel steam coil tank heat Steam booster Electric booster Security package Totally enclosed motor Pressure reduction valve and line strainer DA-3 CA-3 & DA-3 Technical Manual

6 PART TECHNICAL INFORMATION DA-3 Pot and Pan Washer Capacity Per Hour Tank Capacity Motor Size Electric Usage (Electric booster must have 6 gallon holding tank) Steam Consumption at 20 psi Final Rinse Peak Flow at 20 psi min. Final Rinse Consumption at 20 psi min. Exhaust Requirements Peak Rate Drain Flow Shipping Weight Current Draw Amps 208/3/60 230//60 240/3/60 480/3/60 380/3/50 50 racks/276 sheet pans 62 gallons (2) 5 hp 5 kw wash tank (2) 9 kw booster 40º rise (2) 24 kw booster 70º rise 40º rise 20 lbs./hr. tank 50 lbs./hr. booster average 476 lbs./hr. booster peak 70º rise 20 lbs./hr. tank 88 lbs./hr. booster average 834 lbs./hr. booster peak 22.4 gallons/minute 5.6 gallons/cycle 40 gallons/hour Steam 34. N/A CFM 6 gallons/minute 500 lbs. Electric w/o booster 48.0 N/A SPECIFICATIONS CONSTRUCTION- Hood and tank constructed of 4 gauge 8-8 type 304 S/S. Hood unit of all welded seamless construction. S/S frame, legs and feet. All internal castings are non-corrosive lead free nickel alloy or bronze. DOORS- A front inspection/clean-out door and two simultaneously opening operating doors. Operating doors balanced by externally mounted springs. Extra large die formed 8-8 type 304 S/S doors ride in all S/S channels. A triple ply leading edge on the door channels made of S/S. PUMP- Centrifugal type packless pump with a brass petcock drain. Construction includes ceramic seal and a balanced cast impeller on a precision ground stainless steel shaft, extension or sleeve. All working parts mounted as an assembly and removable as a unit without disturbing pump housing. Two 5 hp motors, standard horizontal C-face frame, drip proof, internally cooled with ball-bearing construction. CONTROLS- Side-mounted control cabinet, NEMA 2 rated, housing motor controls and overload protection, transformer, contactors and all dishwasher integral controls. All controls safe low voltage 24 VAC. SPRAY SYSTEM- Wash and rinse spray systems made of 8-8 type 304 S/S pipe threaded into cast hub assemblies. Upper and lower spray assemblies are interchangeable and are removable without the use of tools. WASH- 4 power spinning wash arms above and 4 power spinning wash arms below, each designed with 8 high pressure action cleansing holes. FINAL RINSE- 4 power spinning wash arms above and 4 power spinning rinse arms below, each designed with 3 nozzles. DRAIN- Drain valve externally controlled. Overflow assembly with skimmer cap is removable with the use of simple tools for drain line inspection. Heater is protected by low water level control. *Note: Exhaust requirements are for duct connections only. Note: Due to product improvement we reserve the right to change information and specifications without notice. CA-3 & DA-3 Technical Manual

7 PART TECHNICAL INFORMATION CA-3 & DA-3 POT AND PAN WASHERS INTRODUCTION This manual contains all pertinent information to assist in the proper installation, operation, cleaning, maintenance, and parts ordering for the CA-3 and DA-3 pot and pan washers. The installation instructions are intended for qualified equipment installers. The operation and cleaning instructions are intended for the daily users of the equipment. The maintenance and drawing sections are intended for qualified service and/or maintenance technicians. Replacement parts may be ordered directly from our factory or from your local Authorized Insinger Service Company. Surefire TM Start-Up Program Insinger is proud to offer our exclusive Surefire TM Start-up & Check-out Program to our commercial customers. This service is included in the purchase price of your new Insinger dishwasher. We will provide an authorized factory service technician for the initial start-up of your new Insinger dishwasher to ensure it is running correctly. Please call the factory or your local Insinger Sales or Service Representative to schedule this service. NSF 3 requirements for detergent and chemical sanitizer dispensers This machine must be operated with an automatic detergent feeder and, if applicable, an automatic chemical sanitizer feeder, including a visual means to verify that detergents and sanitizers are delivered or a visual or audible alarm to signal if detergents and sanitizers are not available for delivery to the respective washing system. Please see instructions for electrical and plumbing connections located in this manual and in the feeder equipment manual. Intended Use Insinger dishmachines may only be used for cleaning plates, cups, dishes, cutlery and similar restaurant ware and commercial catering. Any change in design or use of the dishwasher carried out without the written permission of Insinger, will lead to warranty nullification. If damage is caused to the dishwasher due to failure to observe the instructions given in this manual, no claims under the warranty agreement can be submitted to lnsinger Machine Company. DEFINITIONS Throughout this guide you will find the following terms: WARNING, CAUTION, & NOTE. WARNING indicates potential physical danger. CAUTION indicates potential equipment damage. NOTE indicates helpful operating hints or tips. You will visually be able to identify each as shown below: WARNING: Indicates potential physical danger.! CAUTION: Indicates potential equipment damage. NOTE: Indicates helpful operating hints or tips. SAFETY SUMMARY The following are general safety precautions that are not related to any specific procedures. These are recommended precautions that personnel must understand and apply during many phases of operation and maintenance. Keep Away From Live Circuits Operating personnel must at all times observe all safety regulations. Do not replace components or make adjustments inside the equipment with the power supply turned on. Under certain conditions, dangerous potentials may exist when the power control is in the off position. To avoid casualties and injuries, always remove power, red tag and lockout machine, and ground a circuit before touching it. Do Not Service or Adjust Alone Under no circumstances should any person reach into or enter the enclosure for the purpose of servicing or adjusting the equipment except in the presence of someone who is capable of rendering aid. Resuscitation Personnel working with or near high voltages should be familiar with modern methods of resuscitation. Such information may be obtained from the Bureau of Medicine and Surgery. CA-3 & DA-3 Technical Manual

8 PART TECHNICAL INFORMATION INSINGER MACHINE COMPANY LIMITED WARRANTY Insinger Machine Company, Inc. (Insinger) hereby warrants to the original retail purchaser of this Insinger Machine Company, Inc. product, that if it is assembled and operated in accordance with the printed instructions accompanying it, then for a period of either 5 months from the date of shipment from Insinger or year (2 months) from the date of installation or start-up that said Insinger product shall be free from defects in material and workmanship. Whichever one of the two aforestated limited warranty time periods is the shortest shall be the applicable limited warranty coverage time period. Insinger may require reasonable proof of your date of purchase; therefore, you should retain your copy of invoice or shipping document. This limited warranty shall be limited to the repair or replacement of parts which prove defective under normal use and service and which on examination shall indicate, to Insinger s satisfaction, they are defective. Any part that is claimed to be defective and covered by this limited warranty must be returned to Insinger. An RMA# must be obtained from the Insinger Warranty Department before returning any material. Return may be done through an Authorized Service Agency. Furnish serial number of machine and RMA # with shipment and send to: Insinger Machine Company 6245 State Road Philadelphia, PA If Insinger s inspection confirms the defect and the claim, Insinger will repair or replace such part without charge and return it to you freight or postage prepaid. This limited warranty does not cover any failure or accident, abuse, misuse, alteration, misapplication, improper installation, fire, flood, acts of God or improper maintenance or service, or failure to perform normal and routine maintenance as set out in the instruction booklet (operating instructions) or for improper operation or failure to follow normal operating instructions (as set out in the instruction booklet). Insinger is not responsible nor liable for any conditions of erosion or corrosion caused by corrosive detergents, acids, lye or other chemicals used in the washing and or cleaning process. Service must be done by either Insinger Appointed Service Agencies or agencies receiving prior authorization from Insinger. All warranty work must be done during normal working hours, unless purchaser receives prior authorization from Insinger. There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability and fitness are limited in duration to the period of coverage of this express written limited warranty. This limited warranty supersedes all other express warranties, implied warranties of merchant-ability and fitness or limited warranties as of this date, January, 998. Some states do not allow limitation on how long an implied warranty lasts so this limitation may not apply to you. Insinger is not liable for any special, indirect or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation nor exclusion may not apply to you. Insinger does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return or replacement of its equipment: and no such representations are binding on Insinger. CA-3 & DA-3 Technical Manual

9 PART 2 INSTALLATION INSTRUCTIONS CA-3 & DA-3 POT AND PAN WASHERS INSTALLATION INSTRUCTIONS These installation instructions are intended for qualified equipment installers. PLACEMENT Carefully uncrate the machine. Take caution not to damage components which may be mounted on the top or sides of the machine. Set unit in place and adjust the feet to level the machine. TABLING Load and unload tables should be pitched towards the machine to return excess water into the machine. Fasten the tables to the load and unload side of the machine. Most installations require fastening the turndown lip of the dish tables to the side of the machine with flathead counter-sunk screws. The table design should provide horizontal clearance of 30 for servicing. ELECTRICAL CONNECTIONS Connect electrical lines sized for the correct voltage, current and phase of the machine. These should agree with the machine requirements indicated on the nameplate and labels on the control panel. The below Fuse Sizing Chart should be used as a guide for proper line protection. Machines not provided with a single-point connection require two separate electrical connections for:. pumps and control circuit 2. wash tank heater(s) If an electrical booster is provided connect the power directly to the booster. CAUTION: Connections must be made to a circuit breaker or fused disconnect as provided by the end-user and required by local codes. A laminated wiring diagram is inside the control panel. CAUTION: As with any 3 phase system, an electrician must check all motors for proper phasing, i.e., Pump motors must be running in direction indicated by arrow on housing. FUSE SIZING CHART MODEL TYPE 208VAC / 3PH 230VAC / 3PH 380VAC / 3PH 460VAC / 3PH Steam Heat 25A 20A 5A 0A CA-3(C) Electric Heat 35A 35A 20A 20A Gas Heat 25A 20A 5A 0A DA-3 Steam Heat 40A 35A 25A 20A Electric Heat 60A 50A 30A 25A CA-3 & DA-3 Technical Manual

10 PART 2 INSTALLATION INSTRUCTIONS MECHANICAL CONNECTIONS Flush all lines to remove debris. Connect 40 F water lines for tank fills/booster as tagged and noted on the installation drawings. If machine is provided with steam heat, connect the steam lines and steam condensate lines as tagged and noted on installation drawings. Connect the drain lines. CAUTION: Drain lines must be as specified on installation drawings. Drain line should be properly vented and should have fall of not less than /4 to the foot of proper flow. CAUTION: Some area plumbing codes require drains to flow into an open gap with an opening twice the diameter of the pipe. Check with your local plumbing codes for the type of drain connection required. CHEMICALS Upon completed installation of the dishmachine, contact a local detergent/chemical supplier for the correct chemicals for your machine. Electrical connection points for the detergent dispenser and rinse injector are located inside the control panel. Refer to the machine wiring diagram for the proper connection points. Dispensers may be connected on either the primary voltage side of the machine or the 24VAC control voltage side. CAUTION: When connecting on the 24VAC control voltage side of the transformer, total KVA must not exceed 50VA. The detergent density probe should be placed in the hole provided. CAUTION: Do not reduce the size of lines as specified in installation drawings. All lines are sized to facilitate necessary flows, pressures, etc. HVAC Ventilation system should be sized to provide adequate ventilation per machine specs. Refer to spec sheet. CA-3 & DA-3 Technical Manual

11 PART 2 INSTALLATION INSTRUCTIONS Installation Drawing : CA-3 CA-3 & DA-3 Technical Manual

12 PART 2 INSTALLATION INSTRUCTIONS Installation Drawing : DA-3 CA-3 & DA-3 Technical Manual

13 PART 3 OPERATION INSTRUCTIONS CA-3 & DA-3 POT AND PAN WASHERS OPERATION INSTRUCTIONS These instructions are intended for the daily users of this machine. PREPARING MACHINE. Ensure drain overflow tube is in place. Close the tank drain valve. 2. Check for proper installation and cleanliness of all internal, removable components such as suction strainers, scrap screens, and rotating spray pipes. 3. Ensure all water and steam lines are open. 4. Ensure electrical circuits are on. 5. Close machine doors. NOTE: Overloading racks will minimize the proper cleaning of ware. SHUTDOWN. Upon completion of ware cleaning, move the power toggle switch to the OFF position. 2. Drain the machine. 4. Refer to the CLEANING INSTRUCTIONS for proper clean-up of the dishmachine. 5. Report any unusual occurrences to qualified service personnel. STARTING MACHINE. Move the power toggle switch to the ON position. The machine will fill the tank, run through a complete wash/rinse cycle and shut-off. 2. When the tank is full the tank heat will operate automatically. Proper tank heat is 50 F. CAUTION: To ensure proper operation of the auto tank fill feature and the tank heaters, the level float located in each tank MUST be cleaned daily. WASHING WARE. Open doors. 2. Insert a rack of soiled dishware in machine (two racks for the DA-3) and lower doors. 3. Machine will wash and rinse automatically. 4. When the rinse indicator light goes off the cycle is complete. 5. Raise doors and remove rack of clean ware. 6. For continuous operation repeat steps 2-5. CA-3 & DA-3 Technical Manual

14 PART 4 CLEANING INSTRUCTIONS CA-3 & DA-3 POT AND PAN WASHERS CLEANING INSTRUCTIONS DAILY CLEANING The following cleaning procedures should be done daily, at the end of the shift:. Remove all internal removable parts including rotating spray pipes, scrap screens, drain overflow tubes, suction strainers and curtains. 2. Remove the end caps from the spray manifolds and clean with the brush provided. Flush the manifolds. CAUTION: Level floats must be cleaned daily. Build-up of grease and scum will cause faulty operation of tank fill and heating system. CAUTION: Do not remove wash and rinse spray arms from the hubs as these are factory set. Cleaning should be done by removing the endcap on each arm. 3. Flush scrap screens of matter. 4. Clean drain overflow tube. DE5-60: Liquid Level Float CAUTION: V-cup seal on the drain overflow tube may become gummed which will not allow the overflow tube to seat properly. This will cause the drain to leak water. Remove any build-up on the V-cup seal. When the seal becomes worn, replace. 5. Clean suction strainers of build-up. CAUTION: Improper cleaning of suction strainers will cause the pumps to cavitate. This will cause poor washing results. 6. Clean tank level floats ( per tank) with a plastic abrasive pad. DO NOT use steel wool. 7. Rinse nozzles should be cleaned of matter. 8. Doors should be left open to allow drying of interior surfaces.! WEEKLY CLEANING. The entire machine should be wiped down using an industrial grade stainless steel cleaner. 2. Under the supervision of your detergent supplier the machine interior must be properly de-limed. 3. The switch on the control panel labelled MANUAL and the switch labelled WASH should be used when de-liming the machine. When activated, these switches keep the machine in an indefinite wash cycle. This feature can also be used to wash heavily soiled ware. NOTE: The water quality in some areas requires de-liming to be done more frequently. Contact your detergent supplier for recommended de-liming frequency. CA-3 & DA-3 Technical Manual

15 PART 5 MAINTENANCE & REPAIR PROCEDURES CA-3 & DA-3 POT AND PAN WASHERS MAINTENANCE REQUIREMENTS This section is intended for qualified service and/or maintenance technicians. The following maintenance should be conducted quarterly:. Remove and clean the strainer screens on water and steam lines. If the screens cannot be cleaned, replace. 2. Inspect the condition of the fill solenoid valve seats and diaphragms. Replace as necessary. 3. Inspect drain 0-Rings for leakage. Replace where necessary. 4. Check door spring tension and adjust where necessary. 5. Check wash and rinse hub bushing/bearing and replace where necessary. MAINTENANCE PROCEDURES Solenoid Valve Disassembly (SK-5825). Disconnect the power supply to the machine. 2. Turn off the water supply. 3. Remove cap on top of the coil. Remove the coil. 4. Remove the 4 hex bolts and lift bonnet from valve body. Note positioning of spring and plunger. 5. Remove main piston. 6. Inspect for dirt, wear or lime build-up. Clean or replace as required. 7. Reassemble in reverse of disassembly. Line Strainer Disassembly. Shut off water supply. 2. Remove large hex nut on bottom of strainer body. 3. Remove strainer screen. Inspect and clean or replace as necessary. 4. Reassemble in reverse of disassembly. Water flow must be same direction as arrow on line strainer body. Use new gaskets to insure a tight seal. Pump Disassembly Line Strainer Assembly. Before disassembling pump ensure there are no obstructions in the pump intake by removing and cleaning the suction strainer (inside tank). NOTE: It is not necessary to remove the pump housing from the machine to disassemble the pump. 2. Remove the pump motor and impeller adaptor by removing the 4 hex bolts attaching them to the pump housing. 3. Repair or replace the pump parts as required. 4. Reassemble in reverse of disassembly. Wash and Rinse Cycle. The timing sequence consists of two timers. 2. The CA-3, CA-3C, and DA-3 use a five minute timer adjusted to 20 seconds for the wash cycle (P/N DE7-28) 3. They also use a one minute timer adjusted to 5 seconds for the rinse (P/N DE7-27). 4. Should either of these become defective, replace. CA-3 & DA-3 Technical Manual

16 PART 5 MAINTENANCE & REPAIR PROCEDURES Tank Heat Temperature Adjustment A temperature control board is provided in the control panel for easy adjustment of tank temperature. Though tank temperature is set during factory testing it is sometimes necessary to re-adjust the temperature at start-up.. Locate the temperature control board (P/N DE9-25). Use the control panel layout drawing located in PART 7, Electrical Schematics and Parts. 2. Adjust the tank temperature to the correct temperature by turning the potentiometer located on the temperature control board. An arrow on the potentiometer indicates increase. Troubleshooting Tank Temperatures If the temperature does not change follow the below procedures. Electric Heat:. Check the temperature control board (P/N DE9-25) for proper operation. If the temperature control board is faulty, replace. 2. Verify tank heat contactor is working correctly. If not, replace. 3. Verify all immersion heaters are working properly and are not limed. If not, replace. Steam Heat:. Check the temperature control board (P/N DE9-25) for proper operation. If the temperature control board is faulty, replace. 2. Verify steam pressure per machine specifications. 3. Verify steam trap is not clogged. If so, clean and/or replace. Immersion Heater Replacement (SK-4703). The immersion heater MUST be completely submerged at all times. If this is not the case contact a qualified service technician. The heated surface should never be in contact with sludge. 2. Remove the housing covering the wiring terminations. Disconnect the immersion heater wires. 3. Remove the immersion heater by loosening and removing the large hex nut. DE9-25: Tank Temperature Control Board 4. Install in reverse of removal. NOTE: Use plumbers putty as gasketing around the immersion heater installation nut. CA-3 & DA-3 Technical Manual

17 PART 5 MAINTENANCE & REPAIR PROCEDURES Motor Overloads All motors used on Insinger Machines are provided with motor overloads. Motor overloads are adjusted when the machines are factory tested. Should it be necessary to adjust the motor overloads in the field first verify the motor current draw for the voltage the machine is using. Refer to the Control Panel Layout drawing located in PART 7 to identify the overload, adjust by turning the dial to the appropriate AMP draw. Level System The level control system consists of one level timer (P/N DE7-35) and one level float (DE5-60) per tank. When the system is powered-up, the tank(s) will begin to fill (assuming no water is in the tanks). Once the level float is actuated, the timer begins to time-out and continues the filling process until the tank(s) is full. Should the tank heat energize without water in the tank troubleshoot the system to find the problem DE7-35: Liquid Level Timer CAUTION: Dirty level floats will cause the tank heat to energize with no water in the tanks. Level floats MUST be cleaned daily. Motor Overload Relay CA-3 & DA-3 Technical Manual

18 PART 5 MAINTENANCE & REPAIR PROCEDURES SK-5825 : Final Rinse Solenoid Valve CA-3 & DA-3 Technical Manual

19 PART 5 MAINTENANCE & REPAIR PROCEDURES SK-4703 : Electric Heater Installation CA-3 & DA-3 Technical Manual

20 PART 5 MAINTENANCE & REPAIR PROCEDURES SK-2525 : 5 HP Pump Motor Assembly REV A - 07/2/82 ITEM PART NO. DESCRIPTION QTY Motor 5 HP 2 D-439 Adapter 3 D-440 Impeller 4 D-44 Casing 5 D2-566 Gasket, Casing 6 D2-568 Flinger, Shaft 7 D-2494 Seal Assembly 8 D2-567 O-Ring, Shaft 9 D3-88 Sleeve, Shaft 0 D3-89 Retainer, Seal Spring Drain Plug - /4 IPS CA-3 & DA-3 Technical Manual

21 PART 5 MAINTENANCE & REPAIR PROCEDURES TROUBLESHOOTING TECHNICAL ISSUES POSSIBLE CAUSES SOLUTIONS Machine will not operate. No power 2. Blown fuse or tripped breaker 3. Motor overloads tripped. Check power supply 2. Replace fuse; reset breaker 3. Reset overload Tank will not hold water Tank fills beyond overflow Water leaks around door Weak or ineffective spray Weak or ineffective final rinse spray. Drain not closed 2. Drain overflow not seated or installed 3. Pump petcock opened 4. Overflow v-seal dirty/worn. Obstruction in overflow tube or drain line. Doors not seating 2. Clogged spray pipe. Clogged spray pipe 2. Manifolds not installed properly 3. Obstruction in pump 4. Pump rotation reversed 5. Suction strainer clogged. Lime deposits in spray nozzles 2. Low water pressure 3. Clogged line strainer 4. Closed water supply valve. Close drain 2. Reseat or install drain overflow 3. Close pump petcock 4. Clean/replace v-seal. Remove obstruction. Reseat doors 2. Clean spray pipe with brush. Clean spray pipe with brush pipe 2. Ensure proper placement of upper and lower pipes 3. Clear obstruction through pump inspection plate 4. Arrow on pump housing indicates direction, correct electrically 5. Clean suction strainer. Clean or replace nozzles 2. Adjust to 20PSI 3. Remove line strainer and clean 4. Open ball valve Water hammer. Excessive water line pressure. Install water hammer valve Machine vibrates or is noisy Final rinse will not shut off. Pump rotation reversed 2. Pump bearings worn. Final rinse solenoid valve clogged 2. Diaphragm worn 3. Solenoid valve still powered-up. Arrow on pump housing indicates direction, correct electrically 2. Replace pump bearings. Disassemble valve and clean internal parts of scale or replace 2. Replace with solenoid valve repair kit 3. Check final rinse actuating circuit for proper operation CA-3 & DA-3 Technical Manual

22 PART 5 MAINTENANCE & REPAIR PROCEDURES TROUBLESHOOTING TECHNICAL ISSUES POSSIBLE CAUSES SOLUTIONS Tank not filling/tank heat coming on with no water in tank. Level float dirty 2. Level control system not working. Clean level float 2. Troubleshoot level control circuit Tank temperature too low/high. Thermostat not adjusted 2. Heat circuitry not working 3. Electric heat - power turned off 4. Electric heat - immersion heaters limed 5. Steam heat - steam turned off 6. Steam heat - not enough steam 7. Steam heat - condensate traps clogged 8. Gas heat - gas turned off 9. Gas heat - pilot not lit (if provided). Adjust thermostat 2. Troubleshoot circuitry 3. Check circuit breakers 4. De-lime machine 5. Turn steam on 6. Adjust steam pressure per machine specs 7. Clean or replace condensate traps 8. Turn on gas 9. Re-light pilot CA-3 & DA-3 Technical Manual

23 PART 6 PARTS & ASSEMBLIES 72- : CA-3 Assembly ITEM PART NO. DESCRIPTION 72- Discharge Line Assembly Pump & Motor Installation Track & Track Bracket Location Spray Nozzle Assembly - Wash Spray Nozzle Assembly - Rinse Scrap Screen Arrangement Pressure Gauge Installation Shell Assembly 73-0 Control Box Location Drain Assembly Drain Handle Final Rinse Piping w/ Steam Booster Final Rinse Piping w/ Electric Booster Steam Piping (Injector) Steam Coil - Solenoid Operated Grid Installation Assembly 7 D2626 Proximity Switch Location Electric Heater, Liquid Level Float & Diode Junction Locations 5 CA-3 & DA-3 Technical Manual 208 QTY

24 PART 6 PARTS & ASSEMBLIES 73- : DA-3 Assembly ITEM PART NO. DESCRIPTION 73- Discharge Line Assembly Pump & Motor Installation Track & Track Bracket Location Spray Nozzle Assembly - Wash Spray Nozzle Assembly - Rinse Scrap Screen Arrangement Pressure Gauge Installation Shell Assembly 73-0 Control Box Location Drain Assembly Drain Handle Final Rinse Piping w/ Steam Booster 73-4 Final Rinse Piping w/ Electric Booster Steam Piping (Injector) Steam Coil - Solenoid Operated Grid Installation Assembly 7 D2626 Proximity Switch Location Electric Heater, Liquid Level Float & Diode Junction Locations 5 CA-3 & DA-3 Technical Manual 208 QTY

25 PART 6 PARTS & ASSEMBLIES : Spring Counterweight Assembly REV E - 03/4/0 ITEM PART NO. DESCRIPTION QTY Door Arm Weldment, CA Door Arm Weldment, DA Door Arm Door Handle Bracket Door Arm 2 7 SK-2290A Spring Spring Extension Rod Lower Spacer x 7/6 LG Washer 4 D309C-JC-2A Hex Head Screw S/S 3/8 x /2 Lg. 2 2 D309C-JC-9A Hex Head Screw S/S 3/8 x /8 Lg. 2 3 D309C-JC-7A Hex Head Screw S/S 3/8 x 7/8 Lg. 4 4 D32C-JC-5 Locknut (Seal) S/S 3/ D33C-J 3/8 Flat Washer S/S 2 6 D309C-GC-6E Seal Head Screw S/S /4-20 x 3/4 Lg. 4 7 D32C-GC-5 Locknut (Seal) S/S / D2245 Plastic Handle Cover Upper Spacer 5/6 Lg. 2 CA-3 & DA-3 Technical Manual

26 PART 6 PARTS & ASSEMBLIES SK-259A : Drain Assembly REV A - 08/30/82 ITEM PART NO. DESCRIPTION QTY Drain Assembly A Upper Body B Lower Body C Nut D Overflow Tube 5 D-93 Overflow Tube Skimmer Cap 6 D2-557 V Seal Drain Seat 7 D2-548 O-Ring 8 D2-549 O-Ring 9 D-305 Drain Jam Nut 0 D2-550 O-Ring Drain Handle Assembly Bracket 3 D-2407 Ball CA-3 & DA-3 Technical Manual

27 PART 6 PARTS & ASSEMBLIES 72- : CA-3 Discharge Line Assembly REV A - 07/5/94 ITEM PART NO. DESCRIPTION QTY Upper Manifold Assembly Lower Manifold Assembly Discharge Line Tube Assembly Flange Support 5 D2620 Cupseal - Parker D309C-HC-5A Screw Hex Head 5/6-8 x 5/8 S/S 2 7 D32C-HC-5 Locknut 5/ D309C-JC-0A Screw Hex Head 3/8-6 x /4 S/S 9 D32C-JC-5 Locknut 3/ D309C-JC-9A Screw Hex Head 3/8-6 x /8 S/S 5 D309C-JC-A Screw Hex Head 3/8-6 x 3/8 S/S 4 2 D33A-J Washer 3/8, Copper Plumber s Putty AR CA-3 & DA-3 Technical Manual

28 PART 6 PARTS & ASSEMBLIES 73- : DA-3 Discharge Line Assembly REV A - 07/8/94 ITEM PART NO. DESCRIPTION QTY Upper Manifold Assembly Lower Manifold Assembly Discharge Line Tube Assembly Flange Support 2 5 D2620 Cupseal - Parker D309C-HC-5A Screw Hex Head 5/6-8 x 5/8 S/S 4 7 D32C-HC-5 Locknut 5/ D309C-JC-0A Screw Hex Head 3/8-6 x /4 S/S 2 9 D32C-JC-5 Locknut 3/ D309C-JC-9A Screw Hex Head 3/8-6 x /8 S/S 0 D309C-JC-A Screw Hex Head 3/8-6 x 3/ S/S 8 2 D33A-J Washer 3/8, Copper Plumber s Putty AR CA-3 & DA-3 Technical Manual

29 PART 6 PARTS & ASSEMBLIES 72-7 : Wash Spray Nozzle Assembly REV C - 2/23/92 ITEM PART NO. DESCRIPTION QTY Spray Pipe 2 2 D Plug 7/8-9 UNC-2A 2 CA-3 & DA-3 Technical Manual

30 PART 6 PARTS & ASSEMBLIES : Rinse Spray Nozzle Assembly REV C - 0/2/5 ITEM PART NO. DESCRIPTION QTY Spray Pipe Spray Pipe 3 D Plug 9/6-2 UNC-2A 2 4 D2828 Nozzle H/8U CA-3 & DA-3 Technical Manual

31 PART 6 PARTS & ASSEMBLIES : Lower Spray Assembly REV E - 06/05/98 ITEM PART NO. DESCRIPTION QTY Lower Discharge Manifold Wash Arm Hub with Bearing Bearing (without Hub) Rinse Assembly Wash Arm Shaft CA-3 & DA-3 Technical Manual

32 PART 6 PARTS & ASSEMBLIES 72-56A : Lower Manifold & Shaft Sub-Assembly REV A - 02/5/3 CA-3 & DA-3 Technical Manual

33 PART 6 PARTS & ASSEMBLIES : Lower Manifold Assembly REV E - 06/05/98 ITEM PART NO. DESCRIPTION QTY Upper Discharge Manifold Wash Arm Hub with Bearing Bearing (without Hub) Rinse Assembly Wash Arm Shaft CA-3 & DA-3 Technical Manual

34 PART 6 PARTS & ASSEMBLIES : CA-3 Final Rinse Piping with Electric Booster REV K - 03/09/8 CA-3 & DA-3 Technical Manual

35 PART 6 PARTS & ASSEMBLIES : CA-3 Final Rinse Piping with Electric Booster ** * * * * # PART NO. SIZE DESCRIPTION QTY D38F-F-F - Union FIPS x FIPS 2 D Solenoid IPS 3 D34F-FC-00 - Nipple Close IPS 6 4 D Vacuum Breaker IPS 5 D37A-F3-F2 - Adapter C x MIPS 3 6 D207A-B8-6 - Copper Tubing CTS x 4 Lg. 7 D36A-F3-F3-90 O Elbow C 5 8 D38A-F3-F2 - Union C x MIPS A S/S Vertical Rinse Pipe Assembly 0 D326A-F - Locknut IPS D34J-ES-6 - Nipple 3/4 IPS x 2 Lg. 2 D36E-E3-E A 4 D36E-E3-E2-90 O Elbow 3/4 C x 3/4 FIPS Cross x 3/4 x 3/4 x /2 IPS 90 O Elbow 3/4 C x 3/4 MIPS 5 D2390SP - Split Jam Nut 6 D2390SP- - Brass Union A S/S Upper Rinse Pipe 8 D38E-E3-E2-9 D207C-L D207A-B D207A-B Union 3/4 C x 3/4 MIPS S/S Tubing 7/8 OD x 8 /4 Lg. Copper Tubing CTS x 39 Lg. Copper Tubing CTS x 2 3/8 Lg 22 D38A-F3-F3 - Union C * Chrome Plated Brass or Bronze ** 24V (unless otherwise noted) 2 # PART NO. SIZE DESCRIPTION QTY 23 D36A-F3-F - 24 D207A-B D207A-B O Elbow C x FIPS Copper Tubing CTS x 6 /2 Lg. Copper Tubing CTS x 2 Lg. 26 D Drain Cock /4 IPS 27 D322F-F2-B - Reducer MIPS x /4 FIPS 28 D320F-FFF - Tee IPS 29 D322F-E D207A-B D207A-B D207A-B D322F-E2-B - Hex Reducer 3/4 MIPS x /8 FIPS Copper Tubing CTS x 9 /2 Lg. Copper Tubing CTS x 6 Lg. Copper Tubing CTS x 4 /2 Lg. Reducer 3/4 MIPS x /4 FIPS 34 D Petcock /4 IPS 35 D320F-FFE - Tee x x 3/4 IPS 3 36 D328F-E2A - Pipe Plug 3/4 IPS A Support Bracket 38 D D36F-F-F2 - Pressure Regulator & Strainer IPS 90 O Street Elbow FIPS x MIPS 40 D Ball Valve IPS 4 SK Pressure Gauge /4 IPS 42 D328F-A2A - Pipe Plug /8 IPS 43 D36A-F3-F2-44 D207A-B O Street Elbow C X MIPS Copper Tubing CTS x 5 3/8 Lg. NOTE: Pressure Regulator/Strainer (Item 38) to be furnished by others unless specified on production card - use D-2448 Y Strainer as standard. CA-3 & DA-3 Technical Manual

36 PART 6 PARTS & ASSEMBLIES : CA-3 Final Rinse Piping with I-3 Booster REV D - 03/09/8 CA-3 & DA-3 Technical Manual

37 PART 6 PARTS & ASSEMBLIES : CA-3 Final Rinse Piping with I-3 Booster REV D - 03/09/8 CA-3 & DA-3 Technical Manual

38 PART 6 PARTS & ASSEMBLIES : CA-3 Final Rinse Piping with I-3 Booster ITEM PART NO. DESCRIPTION QTY D2379 Ball Valve IPS 2 D2363 Ball Valve /4 IPS 3 D36F-F-F2 90 O Street Elbow FIPS x MIPS 4 D2447 Y Strainer /4 IPS 5 D2396 Steam Temperature Regulator 3/8 IPS 6 D36F-F3-F2 90 O Elbow C x MIPS 3 7 D34F-GC-00 Close Nipple /4 IPS 8 D2947 Solenoid Valve IPS 9 D36F-G-G2 90 O Street Elbow /4 FIPS x /4 MIPS 0 D322F-G2-F Hex Reducer /4 MIPS x FIPS D322F-H2-F Hex Reducer /2 MIPS x FIPS 2 D207A-B8-0 Copper Tubing CTS x 2 /2 Lg. 3 D38A-F3-F2 Union C x MIPS 2 4 D34F-FC-00 Close Nipple IPS 0 5 D2266 Pressure Regulator & Strainer IPS D2443 I-3 Booster (2 ) 8 D320F-FFE Tee FIPS x FIPS x 3/4 FIPS 4 9 D2507 Pressure Relief Valve 3/4 IPS 20 D37A-F3-F2 Adapter C x MIPS 2 D322F-E2-A Hex Reducer 3/4 MIPS x /8 FIPS 2 22 D2497 Petcock /4 IPS 23 SK-443 Pressure Gauge /4 IPS 24 D38F-F-F Street Union FIPS x FIPS 25 D36A-F3-F3 90 O Elbow C 2 26 D322F-E2-D Hex Reducer 3/4 MIPS x /2 FIPS 27 D39A-F3-F2 90 O Union Elbow C x MIPS 2 28 D322F-G2-F Hex Reducer /4 MIPS x FIPS 2 29 D322F-E2-C Hex Reducer 3/4 MIPS x 3/8 FIPS 30 D34F-DS-24 Nipple /2 IPS x 3 Lg. 3 D36F-D-D2 90 O Street Elbow /2 FIPS x /2 MIPS NOTE: Pressure Regulator/Strainer (Item 5) to be furnished by others unless specified on production card - use D-2448 Y Strainer as standard. CA-3 & DA-3 Technical Manual

39 PART 6 PARTS & ASSEMBLIES : CA-3 Final Rinse Piping with I-3 Booster ITEM PART NO. DESCRIPTION QTY 32 D202A Steam Trap /2 IPS 33 D328F-A2A Pipe Plug / D322F-E2-B Hex Reducer 3/4 MIPS x /4 FIPS 35 D320F-FEF Tee FIPS x 3/4 FIPS FIPS 36 D207A-B8-20 Copper Tubing CTS x 5 Lg. 37 D207A-B8-8 Copper Tubing CTS x 4 /2 Lg Bracket 39 D207A-B8-03 Copper Tubing CTS x 25 3/4 Lg. 40 D207A-B8-224 Copper Tubing CTS x 56 Lg Bracket 42 D72A Pipe Clamp S/S Upper Rinse Pipe (Consists of ** items) 44 D207C-L7-73 S/S Tubing 7/8 OD x 8 /4 Lg. 45 D207A-B8-0 Copper Tubing CTS x 4 Lg D2944 Solenoid Valve IPS 48 D2249 Vacuum Breaker IPS D2390SP Split Jam Nut * * 52 D38E-E3-E2 Street Union 3/4 MIPS x 3/4 C 2 53 D207C-L7-68 S/S Tubing 7/8 OD x 42 Lg. 54 D36E-E3-E3 90 O Elbow 3/4 C 55 D326F-F Lock Nut IPS 56 D34C-ES-6 Nipple 3/4 IPS x 2 Lg. S/S Cross x 3/4 x 3/4 x /2 FIPS * * * * 58 D36E-E3-E 90 O Elbow 3/4 C x 3/4 FIPS 59 D36E-E3-E2 90 O Elbow 3/4 C x 3/4 MIPS 60 D2390SP- Brass Union ** D35E-E3-E3 45 O Elbow 3/4 C ** D35E-E3-E4 45 O Street Elbow 3/4 C x 3/4 FTG * Nickel Plated Copper or Brass CA-3 & DA-3 Technical Manual

40 PART 6 PARTS & ASSEMBLIES 73-4 : DA-3 Final Rinse Piping with Electric Booster REV F - 05/07/09 CA-3 & DA-3 Technical Manual

41 PART 6 PARTS & ASSEMBLIES 73-4 : DA-3 Final Rinse Piping with Electric Booster ITEM PART NO. SIZE DESCRIPTION QTY D207A-B Copper Tubing CTS x 20 Lg. ** 2 D2607 Solenoid IPS 2 3 D34F-FC-00 - Nipple Close IPS 5 4 D Vacuum Breaker IPS 2 5 D37A-F3-F2 - Adapter C x MIPS 7 6 D207A-B8-5 - Copper Tubing CTS x /4 Lg. 7 D322F-E2-A - Hex. Reducer 3/4 MIPS x /8 FIPS 2 8 D207A-B8-2 - Copper Tubing CTS x 3 Lg. 2 9 D36A-F3-F3-90 O Elbow C 7 0 D38F-F-F - Street Union FIPS x FIPS 2 D326F-F - Locknut IPS 2 * * * * * 2 D36E-E3-E - 90 O Elbow 3/4 C x 3/4 FIPS 2 3 D34J-ES-6 - Nipple 3/4 IPS x 2 Lg A Cross x 3/4 x 3/4 /2 IPS 2 5 D36E-E3-E2-90 O Elbow 3/4 C x 3/4 MIPS A S/S Upper Rinse Pipe 2 7 D38E-E3-E2 - Union 3/4 C x 3/4 MIPS 4 8 D2930SP- - Brass Union 2 9 D O-Ring A S/S Vertical Rinse Pipe Assembly 2 2 D207C-C S/S Tubing 7/8 OD x 8 /4 Lg D38A-F3-F3 - Union C 2 23 D207A-B Copper Tubing CTS x 2 3/8 Lg D36A-F3-F - 90 O Elbow C x FIPS 2 25 D207A-B8-5 - Copper Tubing CTS x 2 3/4 Lg D207A-B Copper Tubing /4 CTS x 2 Lg. 27 D Drain Cock /4 IPS 2 * Chrome Plated Brass or Bronze ** 24V (unless otherwise noted) CA-3 & DA-3 Technical Manual

42 PART 6 PARTS & ASSEMBLIES 73-4 : DA-3 Final Rinse Piping with Electric Booster ITEM PART NO. SIZE DESCRIPTION QTY 28 D322F-F2-B - Reducer MIPS x /4 FIPS 2 29 D320F-FFF - Tee IPS 2 * 30 D2390SP - Split Jam Nut 2 3 D207A-B Copper Tubing CTS x 9 /2 Lg D207A-B Copper Tubing CTS x 6 Lg D207A-B0-8 - Copper Tubing /4 CTS x 4 /2 Lg. 34 D323F-F2-E - Reducer /4 MIPS x 3/4 FIPS 35 D323F-E2-D - Reducer 3/4 MIPS x /2 FIPS 36 D320F-FFE - Tee /4 IPS 2 37 D328F-E2A - Pipe Plug 3/4 IPS A Support Bracket 39 D-2266A - Pressure Regulator & Strainer /4 IPS 40 D36F-F-F2-90 O Street Elbow IPS 2 4 D Ball Valve /4 IPS 42 D207A-B Copper Tubing CTS x 38 Lg A Support Bracket 2 44 D72-A A Pipe Clamp 2 45 D36A-F3-F4-90 O Elbow C x FTG 2 46 D328F-A2A - Pipe Plug /8 IPS 2 47 D207A-B Copper Tubing CTS x 20 Lg. 48 D207A-B Copper Tubing CTS x 42 Lg D320A-G3-F3-F3 - Tee /4 C x C x C 50 D320F-G-G-G - Tee /4 IPS 2 5 D36F-G-G2-90 O Street Elbow /4 IPS 52 D34F-GC-00 - Nipple Close /4 IPS 3 53 D37A-F3-F2 - Adapter /4 C x /4 MIPS 54 D36A-G3-G3-90 O Elbow /4 C NOTE: Pressure Regulator/Strainer (Item 39) to be furnished by others unless specified on production card - use D-2448 Y Strainer as standard. CA-3 & DA-3 Technical Manual

43 PART 6 PARTS & ASSEMBLIES 73-3 : DA-3 Final Rinse Piping with Two I-3 Boosters REV M - 03/09/8 CA-3 & DA-3 Technical Manual

44 PART 6 PARTS & ASSEMBLIES 73-3 : DA-3 Final Rinse Piping with Two I-3 Boosters REV M - 03/09/8 CA-3 & DA-3 Technical Manual

45 PART 6 PARTS & ASSEMBLIES 73-3 : DA-3 Final Rinse Piping with Two I-3 Boosters ITEM PART NO. DESCRIPTION QTY D2363 Ball Valve /4 IPS 2 2 D34F-GC-00 Close Nipple /4 IPS 5 3 D36F-G-G2 90 O Street Elbow /4 IPS 2 4 D2447 Y Strainer /4 IPS 2 5 D2267 Steam Temperature Regulator /4 IPS 2 6 D39A-G3-G2 90 O Union Elbow /4 C x /4 MIPS 2 7 D320F-GGG Tee /4 IPS 2 8 D328F-G2A Square Plug /4 IPS 2 9 D37A-G3-G2 Adapter /4 MIPS x /4 C 2 0 D207A-B0-33 Copper Tubing /4 CTS x 8 /4 Lg. D322F-H2-G Hex Reducer /2 MIPS x /4 FIPS 2 2 D2379 Ball Valve IPS 2 3 D36F-F-F2 90 O Street Elbow IPS 4 4 D34F-FC-00 Close Nipple IPS 5 5 D2266 Pressure Regulator & Strainer IPS Bracket 7 D2243 I-3 Booster (2 ) 2 8 D320F-FFE Tee FIPS x FIPS x 3/4 FIPS 7 9 D2507 Pressure Relief Valve 3/4 IPS D322F-E2-A Hex Reducer 3/4 MIPS x /8 FIPS 4 22 D2497 Petcock /4 IPS 2 23 SK-433 Pressure Gauge /4 IPS 2 24 D207A-B0-22 Copper Tubing /4 CTS x 5 /2 Lg D36A-F3-F3 90 O Elbow C 6 26 D207A-B8-20 Copper Tubing CTS x 5 Lg D36A-F3-F2 90 O Elbow C x MIPS 2 28 D322F-G2-F Hex Reducer /4 MIPS x FIPS 4 29 D332F-E2-D Hex Reducer 3/4 MIPS x /2 FIPS 2 30 D34F-DS-24 Nipple /2 IPS x 3 Lg. 2 3 D36F-D-D2 90 O Street Elbow /2 IPS x /2 MIPS 2 32 D202A Steam Trap /2 IPS 2 33 D38F-F-F Street Union FIPS x FIPS 2 34 D328F-A2A Square Plug /8 IPS 4 35 D320F-FEF Tee FIPS x 3/4 FIPS x FIPS 2 36 D207A-B8-8 Copper Tubing CTS x 4 /2 Lg. 2 NOTE: Pressure Regulator/Strainer (Item 5) to be furnished by others unless specified on production card - use D-2447 Y Strainer as standard. CA-3 & DA-3 Technical Manual

46 PART 6 PARTS & ASSEMBLIES 73-3 : DA-3 Final Rinse Piping with Two I-3 Boosters ITEM PART NO. DESCRIPTION QTY 37 D207A-B8- Copper Tubing CTS x 0 5/8 Lg Bracket 39 D207A-B8-08 Copper Tubing CTS x 27 Lg. 40 D207A-B8-44 Copper Tubing CTS x Lg. 4 D207A-B8-222 Copper Tubing CTS x 55 /2 Lg. 42 D207A-B8-28 Copper Tubing CTS x 54 /2 Lg. 43 D207A-B0-52 Copper Tubing /4 CTS x 3 Lg. 44 D39A-F3-F2 Union Elbow C x MIPS 2 45 D36A-G3-G3 90 O Elbow /4 C Bracket 2 47 D72A Pipe Clamp S/S Upper Rinse Pipe 2 49 D207C-L7-73 S/S Tubing 7/8 OD x 8 /4 Lg D34F-GS-48 Nipple /4 x 6 Lg. 5 D207A-B8-2 Copper Tubing CTS x 3 Lg D2944 Solenoid Valve IPS 2 53 D2249 Vacuum Breaker IPS 2 54 D37A-F3-F2 Adapter C x MIPS 8 55 D34F-GA-20 Nipple /4 IPS x 2 /2 Lg. 56 D207A-B8-6 Copper Tubing CTS x 4 Lg. 2 * * 57 D38E-E3-E2 Street Union 3/4 C x 3/4 MIPS 4 58 D207C-L7-68 S/S Tubing 7/8 OD x 42 Lg D36E-E3-E3 90 O Elbow 3/4 C 2 60 D326F-F Lock Nut IPS 2 6 D34C-ES-4 Nipple 3/4 IPS x 3/4 Lg. S/S Cross x 3/4 x 3/4 x /2 FIPS 2 * * * * * * 63 D36E-E3-E 90 O Elbow 3/4 C x 3/4 FIPS 2 64 D36E-E3-E2 90 O Elbow 3/4 C x 3/4 MIPS 2 65 D2390SP- Brass Union 2 66 D322F-E2-B Hex Reducer 3/4 MIPS x /4 FIPS 2 67 D2390SP Split Jam Nut 2 68 D39A-F3-F3 Union Elbow C x C 2 69 D35E-E3-E3 45 O Elbow 3/4 C x 3/4 C 2 70 D35E-E3-E4 45 O Elbow 3/4 C x 3/4 CFTG 2 7 D39A-G3-G2 Union Elbow /4 C x /4 MIPS * Nickel Plated Copper or Brass CA-3 & DA-3 Technical Manual