R407C Cellar Cooling. Fansets: Single phase, high efficiency, low

Transcription

1

2 R07C Cellar Cooling Introduction The New Cellarmaster from Climate Center is a simple cost effective range to provide cooling for the smaller cellars within the beer and wine cooling industry. A small specifically designed range of service friendly condensing units and evaporators catering for cooling capacities between 2.9 and 5.7 kw, with rated ambient temperatures up to 38 C. Selections are available with cellar temperatures from 9 C to 12 C, which will meet the range of cooling requirements for compact pub cellars, clubs and wine bars. Sound levels have been minimised throughout the range of CMO condensing units and CMI evaporators. The Range Consisting of accessible CMO outdoor, weatherproof, housed units aligned with compact CMI evaporators, the Climate Center Cellarmaster range is designed for the smaller and medium cellar cooling applications. Cellarmaster CMO condensing units are designed to minimise sound levels, together with an acoustic kit option enabling up to a further 5 db reduction, for noise sensitive locations. The CMI evaporator compact design incorporates an external rotor fan set, reducing sound, resonance and vibration, therefore minimising sound break out into bar and accommodation areas. An optional air heater is available to maintain the desired cellar temperature under winter conditions. CMO Condensing Unit Specification Nominal sound pressure levels: 38 to 9 db at m. Housing: Fully weatherproof, with powder coat grey gloss finish (RAL7036) Compressor: R07C Hermetic complete with crankcase heater. Controls: Externally accessible 20A mains isolator and compressor contactor. Separate preset 26.0 bar HP and 0.7 bar LP pressure switches. Fully wired and enclosed electrical assembly. Fanset: Single phase, high efficiency, low noise external rotor design with integrated guard rated to IP. Service: Maximum access for service maintenance incorporating simple hinged and removable panels. Lid lifts up and latches, with two positions - full open or front access only. Connections: Liquid and Suction copper tubes on right hand side with adequate length to minimise risk of burning case work or cables. Installation: Access without need to remove fixings, with all components fully accessible from one side. CMI Specification Nominal sound pressure levels: 50 to 53 db at 3m Construction : Compact steel chassis design. White, single piece highly durable front panel, incorporating the fan mounting. Drain tray: Tough and durable white ABS design with ¾ inch BSP connection allowing simple removal for cleaning. Fittings readily available to connect to speedfit, copper, polypipe etc. as a standard tap fitting - Wolseley part number Liquid Line: Sealed 053S filter drier. Controls: Industry standard mechanical two stage thermostat mounted on the rear of the evaporator, reducing unnecessary adjustments. Thermostatic expansion valve with bypass capillary for compressor start up. Fansets: Single phase, high efficiency, low noise external rotor design with integrated guard and air straightener rated to IP. Air Throw: Up to 12m for well distributed air movement and even cellar temperatures. Air heater: Optional 1 kw version for winter operation. Service: Front panel, drain tray and end panels are fully removable providing complete access, without the necessity to release the fixings from the ceiling or wall brackets. Simple access to thermostat with end panel removed. Connections: End plates with four slotted fixings provide full access to the connections. Installation: Easily removable endplates with all components fully accessible from one side Options Wall Bracket: Universal design suitable for all CMO condensing units and CMI evaporators. Acoustic Kit: Minimum sound pressure levels are achieved on the CMO condensing units using this option, with reductions up to 5 db at m, when running the fan at minimum speed. The kit comprises the fan speed controller and acoustic lining to the compressor compartment. 2

3 R07C Quick Selection Guide Cellars at Room Temperature of C - Above Ground Cellar Cellar Volume Condensing Unit Part Number Part Number Capacity m 3 230V 1ph 50hz 230V 1ph 50hz (watts) CMI CMI Cellars at Room Temperature of C - Below Ground Cellar Cellar Volume m Condensing Unit Part Number 230V 1ph 50hz CMI07-37 CMI07-69 Part Number 230V 1ph 50hz Capacity (watts) Parameters Ambient temperature: Above ground Cellars 32 C Below ground Cellars 21 C Insulation: 1.2 w/m 2 - equal to an average cellar wall Floor: Concrete to earth Product loading: 16 l/m 3 Product entering temperature: 25 C maximum Product cooling time: 2 hours Occupancy and pump load: 6 w/m 2 Lighting: w/m 2 for hours Plant running time: nominal 18 hours, maximum 19 hours R07C Selection Data Condensing Unit Nominal hp Balanced Capacity in watts - 32 C Ambient Cellar Temperature Balanced Capacity in watts - 38 C Ambient Cellar Temperature 9 C C 11 C 12 C 9 C C 11 C 12 C CMI07-37 CMI

4 CMO Condensing Units Electrical Data Compressor Condensing Unit Supply FLC LRA Start Capacitor (uf) Run Capacitor (uf) AJ5513C AJ5518C FH552C FH5528C 230V 1ph 50hz 230V 1ph 50hz 230V 1ph 50hz 230V 1ph 50hz Fan Motor Condensing Unit Number Diameter (mm) Speed (Poles) Power (watts) 230V 1ph FLC LRA Capacitor (uf) Supply Data Condensing Unit Total Unit FLC Total Unit LRA Motor Rated Fuse Size Motor Rated MCB Size Minimum Cable Size Up to 25m (mm 2 ) 25m to 50m (mm 2 ) These values are recommendations and for guidance only. Additional site factors may need to be taken into consideration. No allowance has been made for derating and correction factors within this guide. If you are in any doubt over the MCB, fuse or cable size selection, please consult a qualified electrician or electrical engineer.

5 CMO Condensing Units Sound Data Sound Pressure Levels Air Volume Condensing Unit Standard db at m Minimum db at m with Acoustic Kit Nominal (m 3 /s) Sound Pressure levels measured over a single semi-reverberant plane in otherwise free field conditions Minimum sound pressure levels are achieved using the acoustic kit, with the fan running at minimum speed The acoustic kit comprises the fan speed controller and acoustic lining to the compressor compartment Acoustic Kit All CMO s - Part Number Weights Condensing Unit Weight (kg)

6 CMO Condensing Units Online Dimensions (mm) CMO

7 CMI s Electrical Data Fan Motor Optional Heater Number Diameter (mm) Speed (Poles) Power (watts) 230V 1ph FLC LRA Capacitor (uf) Power (watts) 230V 1ph FLC CMI07-37 CMI Supply Data Weights Total Unit FLC Motor Rated Fuse Size Motor Rated MCB Size Minimum Cable Size Up to 25m 25m to 50m (mm 2 ) (mm 2 ) Weight (kg) CMI07-37 CMI CMI07-37 CMI These values are recommendations and for guidance only. Additional site factors may need to be taken into consideration. No allowance has been made for derating and correction factors within this guide. If you are in any doubt over the MCB, fuse or cable size selection, please consult a qualified electrician or electrical engineer Air Movement Data Sound Data Air Throw Air Volume At Ceiling Level (m) At 300mm below Ceiling Level (m) Nominal (m 3 /s) Sound Pressure Level db at 3m CMI07-37 CMI CMI07-37 CMI Air throw values are measured in free field conditions with a terminal velocity of 0.25m/s and fitted with air straightener Sound Pressure levels measured over a single semireverberant plane in otherwise free field conditions 7

8 CMI s Outline Dimensions (mm) CMI and 8 LOW RF AI 8

9 CMI s Outline Dimensions (mm) CMI OW RFL AI Recommended CMO and CMI Interconnecting Pipework Sizing Unit Connections Connections Equivalent Interconnecting Line Length Cellar Temperature C Condensing Unit Suction Liquid Suction Liquid m 20m 30m Suction Liquid Suction Liquid Suction Liquid 1/2" 5/8" 5/8" CMI07-37 CMI /" 3/" 3/" 3/" 1/2" 1/2" 3/" 3/" 5/8" 5/8" 3/" 3/" 5/8" 5/8" 3/" 7/8" Line sizing bases on INEOUS Flour / ICI Refrigerant Engineers Tables, 2K loss per 0m 0 C. m selected as unit connection size with duty at 175% maximum of 0m ratings The pipework sizes above are suited for the nominal duty of the CMO and CMI matched together as shown in the table Pipework should be selected based on the total equivalent run length of the interconnecting pipe between the two units, not the dimensional length Additional equivalent lengths for all bends, vertical rises etc, should be added to the basic run lengths to achieve the equivalent run lengths If the equivalent run length exceeds the m setting use 20m, if the run exceeds 20m use 30m, do not uprate or interpolate the readings above 9

10 Universal Support Bracket CMO Condensing Units Mounting Position for the CMO condensing units Bracket shown supporting the CMO condensing unit is the Universal wall mounting kit: Part No

11 Universal Support Bracket CMI s Mounting Position for the CMI s LOW RF AI Bracket shown supporting the CMI evaporator is the Universal wall mounting kit: Part No

12 For further information visit our website at or call into your local branch. Whilst every care has been taken to ensure that the information included in this document was accurate at the time of printing, we reserve the right to change specifications at any time. The photographs reproduced in this publication are within the constraints of the printing process and are NOT to be used for matching purposes. We must also point out that goods will be invoiced at prices ruling at the date of dispatch unless otherwise agreed. E&OE. For all your electrical and heating needs visit our sister companies:- For a better, brighter service For the right degree of service Ref: 7523