2 Minimiser SE - Installation

Transcription

1

2 2 Minimiser SE - Installation

3 Table 1 - Boiler Data GENERAL DATA Boiler Size SE 30 SE 40 SE 50 SE 60 SE 70 SE 80 Gas supply connection (in. BSP) Rc 1/2 (1/2" BSP Female) Flow connection 22mm copper (via adaptors 28mm copper (FEMALE) supplied) (MALE) Return connection 22mm copper (via adaptors 28mm copper (FEMALE) supplied) (MALE) Maximum static water head m (ft.) 30.5 (100) Minimum static water head m (ft.) 0.45 (1.5) Electrical supply 230 V ~ 50 Hz Boiler power consumption 50W Fuse rating External: 3A Internal: F2A to BS 4265 Water content litre (gal.) 1.65 (0.36) 1.95 (0.43) Dry Weight kg (lb.) 26.0 (57.3) 27.0 (59.5) Boiler size Height mm (in.) 600 (23.6) Width mm (in.) 390 (15.0) Depth mm (in.) 270 (10.6) Flue duct diameter mm (in.) 100 (4.0) Table 2 - Performance Data Boiler Size SE 30 SE 40 SE 50 SE 60 SE 70 SE 80 Boiler input Nett kw CV Btu/h 31,400 42,000 52,200 62,800 73,400 84,000 Boiler input Gross kw CV Btu/h 34,900 46,500 58,100 69,800 81,400 93,000 Gas consumption l/s (cu.ft/h) 0.26 (33.6) 0.35 (44.9) 0.44 (56.1) 0.53 (67.3) 0.62 (78.6) 0.70 (89.8) Boiler output 70 C Mean water kw temperature Btu/h 30,000 40,000 50,000 60,000 70,000 80, C Mean water kw temperature Btu/h 32,100 42,800 53,500 64,200 74,900 85,600 Burner Setting mbar pressure (HOT) in.w.g Seasonal Efficiency (SEDBUK) * [86.1]% [86.7]% [86.4]% [86.3]% [86.5]% [86.3]% *The value is used in the UK Government's Standard Assessment Procedure (SAP) for energy rating of dwellings. The test data from which it has been calculated have been certified by BGplc Notes. To obtain the gas consumption:- a. For l/s divide the gross heat input (kw) by C.V. of the gas (MJ/m 3 ) b. For ft 3 /h divide the gross heat input (Btu/h) by C.V. of the gas (Btu/ft 3 ) CAUTION. To avoid the possibility of injury during the installation, servicing or cleaning of this appliance, care should be taken when handling edges of sheet steel components. Minimiser SE - Installation 3

4 Minimiser SE Natural Gas only PI No. 87AT2 Minimiser SE G.C. Appliance No PI No AT 2 Destination Countries: UK, IE CONTENTS Air Supply... 8 Boiler Clearances... 5 Boiler Exploded Diagram Electrical Connections Electrical Supply... 8 Electrical Systems Diagrams Extension Ducts - Fitting Fault Finding Flow Wiring Diagram Flue Fitting Rear outlet Side outlet Flue Installation... 7 Gas Safety Regulations... 6 Gas Supply... 7 Installation Mandatory Requirements... 6 Pump... 9 Servicing Short List of Parts System Diagrams... 9 Terminal Guards... 7 Thermostatic Radiator valves... 8 Water and Systems... 8 Water Connections... 5 Water Treatment Wiring Diagrams TE TO THE INSTALLER: LEAVE THESE INSTRUCTIONS ADJACENT TO THE GAS METER. ALSO COMPLETE THE BENCHMARK LOG BOOK AND GIVE THIS TO THE CUSTOMER. 4 Minimiser SE - Installation

5 1 BOILER WATER CONNECTIONS GENERAL The boiler flow and return pipes are supplied fitted to the boiler ready for top connection but can be removed and adapted for bottom connection, if required, either before or after the boiler is hung on the wall - refer to Frame 43. Notes. a. For the 70 and 80 boilers, 28mm (1") flow and return pipes should be used to and from the boiler. For the 30 to 60 boilers, 22mm (3/4") pipes may be used to connect the boiler, using the 28mm x 22mm adaptors supplied in the hardware pack. b. This appliance is T suitable for use with a direct hot water cylinder. 2 BOILER CLEARANCES all dimensions in mm (in.) The following minimum clearances must be maintained for operation and servicing. Additional space will be required for installation, depending upon site conditions. Side and Rear Flue a Provided that the flue hole is cut accurately, e.g. with a core drill, the flue can be installed from inside the building where wall thicknesses do not exceed 600mm (24"). Where the space into which the boiler is going to be installed is less than the length of flue required the flue must be fitted from the outside. Installation from inside ONLY b. If a core boring tool is to be used inside the building the space in which the boiler is to be installed must be at least wide enough to accommodate the tool. REAR FLUE ONLY MIN. Top clearance required = 145 mm (5 3/4") SIDE FLUE ONLY Horizontal length of flue Top clearance from centre line of boiler required (MIN.) to outside wall Dimn. A 0.5 m 160 mm (6 5/16") 1.0 m 180 mm (7 7/8") 1.5 m 205 mm (8 1/16") 2.0 m 225 mm (8 7/8") 2.5 m 250 mm (9 3/4") 3.0 m 270 mm (10 5/8") Front clearance: 450mm (17 3/4") from the front of the boiler casing. The minimum front clearance when built in to a cupboard is 5mm (1/4") Dimension y Boiler only with standoff brackets 154mm 124mm (4 7/8") (6 1/16") For side outlet flues: Raise the centre line of the hole in the wall by 5mm +4mm/100mm of flue length Minimiser SE - Installation 5

6 INTRODUCTION Minimiser SE are fully automatically controlled, wall mounted, low water content, balanced flue, fanned super efficient condensing gas boilers. They are spot-rated to provide central heating outputs of 8.8 kw (30,000 Btu/h) to 23.4 kw (80,000 Btu/h). GENERAL Detailed recommendations are contained in the following British Standard Codes of Practice: BS BS Low pressure installation pipes. Installation of gas fired hot water boilers of rated input not exceeding 60 kw. Due to the high efficiency of the boiler a plume of water vapour will form at the flue terminal during operation. The boiler casing is of white painted mild steel with a drop- down control pod door. The controls pod, also of white painted mild steel, has fixed sides and a removable bottom panel. The boiler thermostat is located behind the controls pod door. The heat exchanger is of aluminium. BS BS BS. 5440:1 BS. 5440:2 Forced circulation hot water systems. Installation of gas hot water supplies for domestic purposes (2nd Family Gases) Flues (for gas appliances of rated input not exceeding 60 kw) Ventilation (for gas appliances of rated input not exceeding 60 kw) Note. These boilers cannot be used on systems which include gravity circulation. The boilers are suitable for connection to fully pumped, open vented or sealed water systems. Adequate arrangements for completely draining the system by provision of drain cocks MUST be provided in the installation pipework. Health & Safety Document No. 635 The Electricity at Work Regulations, The manufacturer s notes must T be taken, in any way, as overriding statutory obligations. OPTIONAL EXTRA KITS Programmer Kit Roof Flue Kit Powered Vertical Flue Fits neatly within the casing. Separate fitting instructions are included with this kit. For vertical flue connection. For extended vertical flue connection. Extension Ducts Pack D up to 3.0m (122"). Flue Elbow Kits 90 Degree pack 45 Degree pack (2 per pack) Wall Mounting Stand-off Kit Enables the boiler to be mounted flush with the front of 300mm deep kitchen units. SAFETY Current Gas Safety (Installation and Use) Regulations, or rules in force. It is law that all gas appliances are installed and serviced by a CORGI registered installer (identified by ) in accordance with the above regulations. Failure to install appliances correctly could lead to prosecution. It is in your own interest, and that of safety, to ensure the law is complied with. The installation of the boiler MUST also be in accordance with the latest I.E.E (BS 7671) Wiring Regulations, local building regulations, bye-laws of the local water authority, the building regulations and the Building Standards (Scotland) and any relevant requirements of the local authority. IMPORTANT. These appliances are CE certificated for safety and performance. It is, therefore, important that no external control devices, e.g. flue dampers, economisers etc., are directly connected to these appliances unless covered by these Installation and Servicing Instructions or as otherwise recommended by Caradon Plumbing Limited in writing. If in doubt please enquire. Any direct connection of a control device not approved by Caradon Plumbing Ltd. could invalidate the certification and the normal appliance warranty. It could also infringe gas safety regulations and the above regulations. SAFE HANDLING OF SUBSTANCES. Care should be taken when handling the boiler insulation panels, which can cause irritation to the skin. No asbestos, mercury or CFCs are included in any part of the boiler. LOCATION OF BOILER The boiler must be installed on a flat and vertical wall, capable of adequately supporting the weight of the boiler and any ancillary equipment. The boiler may be fitted on a combustible wall and insulation between the wall and the boiler is not necessary, unless required by the local authority. The boiler must not be fitted outside. Timber Framed Buildings If the boiler is to be fitted in a timber framed building it should be fitted in accordance with the Institute of Gas Engineering document IGE/UP/7: Minimiser SE - Installation

7 GENERAL Bathroom Installations The boiler may be installed in any room or internal space, although particular attention is drawn to the requirements of the current I.E.E. (BS.7671) Wiring Regulations and, in Scotland, the electrical provisions of the building regulations applicable in Scotland with respect to the installation of the boiler in a room or internal space containing a bath or shower. Where a room sealed appliance is installed in a room containing a bath or shower then the appliance and any electrical switch or appliance control utilising mains electricity should be so situated that it cannot be touched by a person using the bath or shower. Where installation will be in an unusual location, special procedures may be necessary and BS 6798 gives detailed guidance on this aspect. Compartment Installations A compartment used to enclose the boiler should be designed and constructed specially for this purpose. An existing cupboard or compartment may be used, provided that it is modified for the purpose. In both cases details of essential features of cupboard / compartment design, including airing cupboard installation, are to conform to the following: BS The position selected for installation MUST allow adequate space for servicing in front of the boiler. Ventilation of the compartment is not necessary. For the minimum clearances required for safety and subsequent service, see the wall mounting template and Frame 2. In addition, sufficient space may be required to allow lifting access to the wall mounting plate. GAS SUPPLY The local gas supplier should be consulted, at the installation planning stage, in order to establish the availability of an adequate supply of gas. An existing service pipe must T be used without prior consultation with the local gas supplier. A gas meter can only be connected by the local gas supplier or by a registered CORGI installer. An existing meter should be checked, preferably by the gas supplier, to ensure that the meter is adequate to deal with the rate of gas supply required. A minimum working gas pressure of 20 mbar MUST be available at the boiler inlet. Installation pipes MUST be fitted in accordance with BS Pipework from the meter to the boiler MUST be of an adequate size, i.e. not less than 15mm O.D. Note. For pipe runs greater than 3m (10'), 22mm O.D. pipe must be used. Do not use pipes of smaller size than the boiler inlet gas connection. The complete installation MUST be tested for gas soundness and purged as described in the above code. FLUE INSTALLATION Pluming will occur at the termination so, where possible, terminal positions which could cause a nuisance should be avoided. The flue must be installed in accordance with the recommendations of BS. 5440: Part 1. Minimiser SE - Installation The following notes are intended for general guidance. 1. The boiler MUST be installed so that the terminal is exposed to external air. 2. It is important that the position of the terminal allows the free passage of air across it at all times. 3. Minimum acceptable spacing from the terminal to obstructions and ventilation openings are specified in Table Table 3 - Balanced 3. flue terminal position Note positions 2-6: Due to the terminal design, installation is possible with clearances less than those specified in BS 5440, Part 1. Terminal Position 4. Where the lowest part of the terminal is fitted less than 2m (6'6") above a balcony, above ground or above a flat roof to which people have access, then the terminal MUST be protected by a purpose designed guard. The minimum spacing in Table 3, Nos. 2, 3, 4, 5 and 6 would be 75mm, in order to allow a terminal guard to be fitted. Terminals guards are available from boiler suppliers - ask for Tower Flue Guard, Model K1. In case of difficulty seek advice from: Tower Flue Components Ltd., Vale Rise, Tonbridge, Kent TN9 1TB Telephone No Ensure that the guard is fitted centrally. Minimum Spacing 1. Directly below or alongside an opening window, air vent or other 300 mm (12") ventilation opening 2. Below guttering, drain pipes or soil pipes 25 mm ( 1") 3. Below eaves 25 mm ( 1") 4. Below balconies or a car port roof 25 mm ( 1") 5. From vertical drain pipes or soil pipes 25 mm ( 1") 6. From internal or external corners 25 mm ( 1") 7. Above adjacent ground, roof or balcony level 300 mm (12") 8. From a surface facing the terminal 600 mm (24") 9. From a terminal facing a terminal 1200 mm (48") 10. From an opening in a car port (e.g. door or window) into dwelling 1200 mm (48") 11. Vertically from a terminal on the same wall 1500 mm (60") 12. Horizontally from a terminal on the wall 300 mm (12") 5. Where the terminal is fitted within 850mm (34") of a plastic or painted gutter or 450mm (18") of painted eaves then an aluminium shield at least 750mm (30") long should be fitted to the underside of the gutter or painted surface. 6. The air inlet/products outlet duct and the terminal of the boiler MUST T be closer than 25mm (1") to combustible material. Detailed recommendations on the protection of combustible material are given in BS. 5440: Where it is essential that the terminal wall plate is fitted, i.e. wall thicknesses over 610mm (24") or with an inaccurately cut hole, the minimum spacing in Table 3, Nos. 2, 3, 4, 5 and 6 would be 60mm (2.4") in order to allow the terminal wall 7

8 GENERAL plate to be fitted. IMPORTANT. It is absolutely ESSENTIAL to ensure, in practice, that products of combustion discharging from the terminal cannot re-enter the building or any other adjacent building through ventilators, windows, doors, other sources of natural air infiltration, or forced ventilation / air conditioning. If this should occur the appliance MUST be turned OFF, labelled as 'unsafe' and corrective action taken. TERMINAL The terminal assembly can be adapted to accommodate various wall thicknesses. Refer to Frame 11 - Unpacking. AIR SUPPLY It is T necessary to have a purpose-provided air vent in the room or internal space in which the boiler is installed. Neither is it necessary to ventilate a cupboard or compartment in which the boiler is installed, due to the low surface temperatures of the boiler casing during operation; therefore the requirements of BS 6798, Clause 12, and BS 5440:2 may be disregarded. WATER CIRCULATION SYSTEM The boiler must T be used for direct hot water supply. For the types of system and correct piping procedure see Frames 1, and 3 to 8. The central heating system should be in accordance with BS and, in addition, for smallbore and microbore systems, BS WATER TREATMENT - see Frame 9 The hot water storage cylinder MUST be of the indirect type and should preferably be manufactured of copper. Single feed, indirect cylinders are not recommended and MUST T be used on sealed systems. The appliances are T suitable for gravity central heating nor are they suitable for the provision of gravity domestic hot water. The hot water cylinder and ancillary pipework, not forming part of the useful heating surface, should be lagged to prevent heat loss and any possible freezing - particularly where pipes run through roof spaces and ventilated underfloor spaces. The boiler must be vented. Draining taps MUST be located in accessible positions, which permit the draining of the whole system - including the boiler and hot water storage vessel. They should be at least 1/2" BSP nominal size and be in accordance with BS The boiler is fitted with a special drain plug which is provided to drain the BOILER ONLY in the event of the system drain plug being unable to do so. The hydraulic resistance of the boilers, at MAXIMUM OUTPUT, with an 11 o C (20 o F) temperature differential, is shown in Boiler size SE30 SE40 SE50 SE60 SE70 SE80 Boiler kw Output Btu/h 30,000 40,000 50,000 60,000 70,000 80,000 Water Flow l/sec Rate gpm Pressure kpa Loss m ft Table 4. Table 4 - Water flow rate and pressure loss THERMOSTATIC RADIATOR VALVES (TRV) Caradon Plumbing Ltd. recommend that heating systems utilising full thermostatic radiator valve control of temperature in individual rooms should also be fitted with a room thermostat controlling the temperature in a space served by radiators not fitted with such a valve as stated in BS When thermostatic radiator valves are used, the space heating temperature control over a living area having a heating requirement of at least 60% of the boiler heat output should be achieved using a room thermostat whilst other rooms are individually controlled by thermostatic radiator valves. A higher proportion of TRVs may be used, provided that a bypass between the boiler flow and return is fitted, to ensure adequate flow when all TRVs are closed - however this is T recommended as a large proportion of TRVs can restrict water circulation and inhibit the condensing mode of condensing boilers, reducing fuel economy. For further information refer to the 'Good Practice Guide 143', publication of the Energy Efficiency Office, available from the Building Research Establishment, Garston, Watford WD2 7JR. Tel: ELECTRICAL SUPPLY Wiring external to the appliance MUST be in accordance with the current I.E.E. (BS.7671) Wiring Regulations and any local regulations which apply. The point of connection to the mains should be readily accessible and adjacent to the boiler, except for bathroom installations where the point of connection to the mains MUST be situated outside of the bathroom. Note. Where a room sealed appliance is installed in a room containing a bath or shower then the appliance and any electrical switch or appliance control utilising mains electricity should be so situated that it cannot be touched by a person using the bath or shower. See Frame 34 for details. CONDENSATE DRAIN - Refer to Frame 44 A condensate drain is provided on the boiler. This drain must be connected to a drainage point on site. All pipework and fittings in the condensate drainage system MUST be made of plastic - no other materials may be used. IMPORTANT. Any external runs must be insulated The drain outlet on the boiler is standard 3/4" (22 mm) overflow pipe. 8 Minimiser SE - Installation

9 3 OPEN VENT SYSTEM REQUIREMENTS The system should be vented directly off the boiler flow pipe, as close to the boiler as possible. The cold feed entry should be inverted and MUST be positioned between the pump and the vent, and not more than 150mm (6") away from the vent connection. GENERAL Note. Combined feed and vent pipes may also be fitted. There should be a minimum height, 450mm (18"), of open vent above the cistern water level. If this is not possible refer to Frame 5. The vertical distance between the highest point of the system and the feed/expansion cistern water level MUST not be less than 450 mm (18"). The pump must be fitted on the flow side of the boiler. A suitable pump is a domestic circulator capable of providing a maximum 11 C (20 F) temperature differential across the boiler with the whole of the heating circuit open (e.g. Grundfos UPS 15/50, 15/60 or equivalent). With the minimum flow circuit allowed by the controls the differential must not exceed 15 C. The vertical distance between the pump and feed/expansion cistern MUST comply with the pump manufacturer's minimum requirements, to avoid cavitation. Should these conditions not apply either lower the pump position or raise the cistern above the minimum requirement specified by Caradon Plumbing Ltd. The isolation valves should be fitted as close to the pump as possible. Return & flow connections SE = 22 mm SE = 28 mm all dimensions in mm (in.) 4 SCHEMATIC PIPEWORK AND SYSTEM BALANCING The boiler does not normally need a bypass but at least some radiators on the heating circuit, of load at least 60% of the boiler output, must be provided with twin lockshield valves so that this minimum heating load is always available (see footnote re. thermostatic radiator valves). Balancing 1. Set the programmer to ON for both CH and HW. Turn the cylinder thermostat down. Close the manual or thermostatic valves on all radiators, leaving the twin lockshield valves (on the radiators referred to above) in the open position. Turn up the room thermostat and adjust these lockshield valves to give boiler flow and return temperatures not more than 15 C apart. These valves should now be left as set. 2. Open all manual or thermostatic radiator valves and adjust the lockshield valves on remaining radiators to give around 11 C temperature drop at each radiator. 3. Turn up the cylinder thermostat and adjust the cylinder balancing valve so that the cylinder achieves a maximum flow consistent with adequate flow to the radiators. Check that with only the domestic hot water loop in circuit a differential temperature of 15 C across the boiler is not exceeded. 4. Adjust room and cylinder thermostats and programmer to RMAL settings. Thermostatic Radiator Valves Caradon Plumbing Ltd. support the recommendations made in BS. 5449, and by leading manufacturers of domestic heating controls, that heating systems utilising the thermostatic radiator valve control of temperature in individual rooms shall also be fitted with a room thermostat, controlling the temperature in a space served by radiators not fitted with such a valve. Such an arrangement will provide for potentially more efficient control of the environment and will also avoid the continuous running of the circulation pump during programmed heating ON periods - thus saving electrical energy. It is, therefore, strongly recommended that, when thermostatic radiator valves are used, space heating temperature control over a living/dining area or a hallway having a heating requirement of at least 60% of the boiler heat output, is achieved using a room thermostat whilst other rooms are individually controlled by thermostatic radiator valves. Minimiser SE - Installation 9

10 GENERAL 5 LOW HEAD AND LARGE SYSTEMS WITH EXTENSIVE PIPE RUNS - OPEN VENT This arrangement is useful for large systems where radiators at the extremities are difficult to vent. This can lead to pumping over with conventional feed and vent arrangements. The following conditions MUST be observed: 1. The top of the automatic air vent must be below the cold water level. 2. The static water level (cold) must be at least 200mm above the top of the horizontal flow pipe, fitted as shown. The vent connection MUST T be made immediately off the top of the boiler as venting is made less efficient. 3. The maximum practical length of 22mm cold feed pipe should be used in order to reduce the effective volume of hot system water expanding into the feed/ expansion cistern to a minimum. Note. The pump manufacturers' minimum requirements must be complied with. All dimensions in mm (in.). NB. Imperial dimensions are approximate 6 SEALED SYSTEM REQUIREMENTS Note. The method of filling, refilling, topping up or flushing sealed primary hot water circuit from the mains via a temporary hose connection is only allowed if acceptable to the local water authority. 1. General a. The installation must comply with the requirements of BS and BS b. The installation should be designed to work with flow temperatures of up to 82 C. c. All components of the system, including the heat exchanger of the indirect cylinder, must be suitable for a working pressure of 3 bar (45lb/in 2 ) and temperature of 110 C. Care should be taken in making all connections so that the risk of leakage is minimised. 2. Safety Valve A spring loaded safety valve complying with the relevant requirements of BS must be fitted in the flow pipe as close to the boiler as possible and with no intervening valve or restriction. The valve should have the following features: a. A non-adjustable preset lift pressure not exceeding 3bar (45lb/in 2 ). b. A manual testing device. c. Provision for connection of a discharge pipe. The valve or discharge pipe should be positioned so that the discharge of water or steam cannot create a hazard to the occupants of the premises or cause damage to electrical components and wiring. 3. Pressure Gauge A pressure gauge covering at least the range 0-4 bar (0-60 lb/in 2 ) must be fitted to the system. The gauge should be easily seen from the filling point and should preferably be connected at the same point as the expansion vessel. 10 Minimiser SE - Installation

11 GENERAL 7 SEALED SYSTEM REQUIREMENTS - continued 4. Expansion Vessel a. A diaphragm type expansion vessel must be connected to a point close to the inlet side of the pump, the connecting pipe being not less than 15 mm (1/2" nominal) size and not incorporating valves of any sort. b. The vessel capacity must be adequate to accept the expansion of the system water when heated to 110 C (230 F). c. The charge pressure must not be less than the static water head above the vessel. The pressure attained in the system when heated to 110 C (230 F) should be at least 0.35 bar (5 Ib/in 2 ) less than the lift pressure of the safety valve. For guidance on vessel sizing refer to the table in Frame Cylinder For further details refer to BS. 5449, BS. 7074:1 and the British Gas Corporation publication 'Material and Installation Specifications for Domestic Central Heating and Hot Water'. The cylinder must be either of the indirect coil type or a direct cylinder fitted with an immersion calorifier which is suitable for operating on a gauge pressure of 0.35 bar (5 Ib/in 2 ) in excess of the safety valve setting. Single feed indirect cylinders are not suitable for sealed systems. 6. Make-up Water Provision must be made for replacing water loss from the system, either: a. From a manually filled make-up vessel with a readily visible water level. The vessel should be mounted at least 150 mm (6") above the highest point of the system, and be connected through a non-return valve to the system, fitted at least 300 mm (12") below the make-up vessel on the return side of the domestic hot water cylinder or radiators. or b. Where access to a make-up vessel would be difficult by pre-pressurisation of the system. Refer to 'Filling', below. 7. Mains Connection There must be no direct connection to the mains water supply or to the water storage tank supplying domestic water, even through a non-return valve, without the approval of the local water authority. 8. Filling The system may be filled by one of the following methods: a. Through a cistern, used for no other purposes, via a ball valve permanently connected directly to a service pipe and/or a cold water distributing pipe. The static head available from the cistern should be adequate to provide the desired initial system design pressure. The cold feed pipe from the cistern should include a non-return valve and a stop valve with an automatic air vent connected between them, the stop valve being located between the system and the automatic air vent. The stop valve may remain open during normal operation of the system if automatic water make-up is required. b. Through a self-contained unit comprising a cistern, pressure booster pump (if required) and, if necessary, an automatic pressure reducing valve and flow restrictor. The cistern should be supplied through a temporary connection from a service pipe or cold water distributing pipe. This unit may remain permanently connected to the heating system to provide limited automatic water make-up. Where the temporary connection is supplied from a service pipe or distributing pipe which also supplies other draw-off points at a lower level then a double check valve shall be installed upstream of the draw-off point. c. Through a temporary hose connection from a draw-off tap supplied from a service pipe under mains pressure. Where the mains pressure is excessive a pressure reducing valve shall be used to facilitate filling. The following fittings shall form a permanent part of the system and shall be fitted in the order stated: A stop valve complying with the requirements of BS. 1010, Part 2 (the hose from the draw-off tap shall be connected to this fitting). A test cock. A double check valve of an approved type. Thoroughly flush out the whole of the system with cold water, without the pump in position. With the pump fitted, fill and vent the system until the pressure gauge registers 1.5 bar (21.5lb/in 2 ). Examine for leaks. Check the operation of the safety valve by manually raising the water pressure until the valve lifts. This should occur within ± 0.3 bar (± 4.3lb/in 2. ) of the preset lift pressure. Release water from the system until the initial system design pressure is reached. Light the boiler and heat the system to the maximum working temperature. Examine for leaks. Turn off the boiler and drain the system while still hot. Refill and vent the system. Adjust the initial pressure to the required value. Sizing procedure for expansion vessels: The volume of the expansion vessel (litres) fitted to a sealed system shall not be less than that given by the table on the following page, multiplied by a factor of 0.8 (for flow temperatures of less than 83 C). Minimiser SE - Installation 11

12 GENERAL 8 SEALED SYSTEM REQUIREMENTS - continued Safety valve setting 3.0 bar 2.5 bar 2.0 bar Vessel charge and initial system pressure bar bar bar bar bar bar bar bar Total water content of system Expansion vessel volume litres 25 litres Multiplying factors for other system volumes WATER TREATMENT The Minimiser boiler has an ALUMINIUM alloy heat exchanger If water treatment is used Caradon Plumbing Limited recommend only the use of FERX-COPAL or SENTINEL X100 water treatment products, which must be used in accordance with the manufacturers' instructions. For further information contact:- Fernox Manufacturing Co. Ltd. Britannica Works Clavering Essex CB11 4QZ Sentinel Division Betz Dearborn Ltd. Widnes Cheshire WA8 8UD IMPORTANT. The application of any other treatment to this product will render the guarantee of Caradon Plumbing Limited invalid. Notes. 1. It is most important that the correct concentration of the water treatment product is maintained in accordance with the manufacturers' instructions. 2. If the boiler is installed in an existing system any unsuitable additives MUST be removed by thorough cleansing. BS. 7593:1992 details the steps necessary to clean a domestic central heating system. 3. In hard water areas, treatment to prevent lime scale may be necessary - however, the use of artificially softened water is T permitted. 4. Under no circumstances should the boiler be fired before the system has been thoroughly flushed. 12 Minimiser SE - Installation

13 10 BOILER ASSEMBLY - Exploded view INSTALLATION INSTALLATION LEGEND A. Boiler drain point 1. Main burner 3. Gas valve 4. Control box 8. Pressure switch 10. Spark generator 11. Control thermostat 12. Overheat thermostat 13. Dry fire thermostat 14. Flue thermostat 15. Condensate siphon 16. Thermostat knob 17. Fan assembly 18. Front panel 19. Controls door 20. Bottom panel 23. Low pressure sensing pipe 24. Fan pressure sensing pipe 25. Heat exchanger 26. Flow pipe 27. Return pipe 36. Wall mounting plate Minimiser SE - Installation 13

14 INSTALLATION INSTALLATION 11 UNPACKING The boiler is supplied fully assembled in one Pack A, together with a standard flue assembly for lengths up to 406mm, rear or side flue outlet, in Pack B. Optional extras (Programmer Kit, Vertical Flue Kits, Extension Duct Pack D and Wall Mounting Stand-off Kit), if ordered, are available in separate boxes. Unpack and check the contents. Pack A Contents Also contained in Pack A: Hardware Pack (listed below). These Installation & Servicing Instructions. The User's Instructions. Hardware Pack 50mm x No.10 wood screws - 3 off. Wall plugs (TP2B ) - 3 off. Water treatment warning label. Condensate drain adaptor. Turret clamp and seal. 22mm x 28mm flow and return pipe connectors (SE30 to SE60 boilers ONLY). M5 x 10 pozi Hex screw. Pack B Contents No. 8 x 8mm self tapping screws - 2 off. Flue support cutting aid - 1 off. No.10 x 2" screws - 4 off. Rawlplugs - 4 off. 12 PACKAGING AND PANEL REMOVAL 1. Unpack the boiler. Note. The hardware pack and wall mounting plate are within the cardboard infill pieces. 2. Swing open the controls pod door. 3. Remove the single screw retaining the casing front panel. 4. Lift the front panel upward and forward and place to one side to avoid damage. 5. Close the controls pod door. 6. Remove the boiler from its packaging base. 14 Minimiser SE - Installation

15 INSTALLATION 13 BOTTOM PANEL REMOVAL 1. Undo the 3 retaining screws. 2. Push the panel backward then to the right to withdraw it from the boiler. 3. Unpack the boiler flue kit (and extension packs, if used). INSTALLATION 14 DETERMINING THE FLUE LENGTH AND FLUE PACKS REQUIRED IMPORTANT. The boiler MUST be installed in a vertical position Dimension X - Wall thickness Dimension Y - Wall thickness plus boiler spacing (RHS) Dimension Z - Wall thickness plus boiler spacing (LHS) Flue length dimension Flue Rear flue Right hand side Left hand side packs dimn. X flue dimn. Y flue dimn. Z required mm mm mm Pack B, cut down (4 1/2-22 3/4") (4 1/2-18" ) (4 1/2-21 1/2" ) as in Frames 18 & mm mm mm Pack B - 1 off (22 3/4-60 1/4") ( /2") (21 1/2-59") Pack D - 1 off mm mm mm Pack B - 1 off (60 1/4-97 3/4") (55 1/2-93") ( /2") Pack D - 2 off FLUE KITS Pack B - supplied as standard Pack D - optional extension kit for side flue or rear flue outlet. Refer to 'Flue Extension Ducts' mm mm mm Pack B - 1 off (97 3/4-118") (93-118") (96 1/2-118") Pack D - 3 off Notes. 1. The flue duct MUST be inclined at to the horizontal to allow condensate to drain back into the boiler and out through the condensate drain. 2. If the front of the boiler is to be flush with the front of 300mm deep kitchen units then the optional stand-off bracket kit should be used. Care must be taken when cutting the ducts and marking the wall to suit this condition. Minimiser SE - Installation 15

16 15 FLUE ASSEMBLY - Exploded View 1. An optional flue duct extension kit is required for wall thicknesses greater than 580mm (22 3/4"). Refer to Frame When cutting the ducts always use the cardboard support cutting aid provided. INSTALLATION LEGEND 1. Terminal. 2. Weather seal. 3. Duct assembly. 4. No. 8 x 8 self tapping screw. 5. Flue Turret. 6. M5 x 10 pozi screw. 7. Turret clamp. 8. Turret seal. REAR FLUE OUTLET 16 WALL MOUNTING TEMPLATE Note. The template shows the positions for the fixing holes and the flue hole centres for standard installation. Care must be taken to ensure the correct holes are drilled. 1. Separate the templates and discard template B. 2. Tape template into the selected position. 3. Ensure squareness by hanging a plumbline as shown. 4. Mark onto the wall the following: a The plate screw positions (choose one from each group) and lower fixing screw position. b. The position of the flue duct hole. Note. Mark the centre of the hole as well as the circumference 5. Remove the template from the wall. 17 PREPARING THE WALL IMPORTANT. Ensure that, during the cutting operation, masonry falling outside of the building does not cause damage or personal injury. 1. Cut the flue hole (preferably with a 5" core boring tool), ensuring that the hole is square to the wall. Both wall faces immediately around the cut hole should be flat. 2. Drill 3 holes with a 7mm (1/4") masonry drill and insert the plastic plugs provided, for the wall mounting plate and the jacking screw plate. 3. Locate two No.10 x 2" screws in the wall mounting plate (one at each side, in any of the 3 holes provided at each side) and screw home. Note. If the terminal is to be sited within 25-40mm of a corner or vertical pipe (refer to Table 3) then the hole MUST be accurately cut and the rubber weather seal trimmed around the groove provided. The terminal wall plate need not be fitted. 16 Minimiser SE - Installation

17 INSTALLATION 18 CUTTING THE FLUE Wall thicknesses of 114 to 580mm Note. If the optional stand-off bracket kit is used it is essential that 30 mm is added to the measured wall thickness when marking the flue (to allow for the thickness of the brackets). 1. Measure and note wall thickness X. 2. Add 15mm (5/8") to dimension X and, measuring from the groove, cut the tube. 3. To ensure the tube is cut square, mark the flue all the way round. 4. Cut to length, using the cardboard support aid. 5. Remove the cardboard support and any burrs. cardboard support cutting aid 19 ASSEMBLING THE FLUE 1. Fit the 'cut to length' flue on to the flue turret. Note. Ensure the top groove in the flue aligns with the top of the turret. 2. Drill a 3.2mm dia. hole through the flue via the hole present in the turret. 3. Secure the turret to the flue, using the self tapping screw provided. 20 MOUNTING THE BOILER 1. Lift the boiler onto the wall mounting plate, as shown. 2. Check the boiler alignment using a spirit level and adjust as necessary with the jacking screw. 3. Align the hole in the jacking plate with the pre-drilled hole in the wall and fix in position with the No.10 x 2" screw provided. Note. If the front of the boiler is to be flush with the front of 300mm deep kitchen units then the optional stand-off bracket kit should be used - refer to the fitting instructions supplied with the kit. REAR FLUE OUTLET Minimiser SE - Installation 17

18 INSTALLATION 21 CONNECTING THE FLUE TO THE BOILER REAR FLUE OUTLET 22 TERMINAL WALL PLATE This plate allows neat concealment and full compression of the rubber seal. Its use is not essential if the flue hole and flue ducts have been accurately cut and the outside wall face is flat. 1. Position the terminal wall plate over the terminal. 2. Drill 4 fixing holes with a 7mm (1/4") masonry drill. 3. Insert the 4 plastic plugs provided. 4. Secure the plate with 4 of the No.10 x 2" screws provided. Note. If the terminal is less than 2m (6' 6") above ground level, an approved terminal guard should be fitted. Refer to 'Flue Installation', Page 7. Note. BEFORE fitting the flue turret, fill the condensate siphon within the boiler by pouring a cupful of water into the flue outlet A. 1. Insert the flue assembly through the prepared hole in the wall far enough to allow the rubber seal to unfold completely and form an adequate seal on the outside wall. 2. Pull the flue back and locate the flue turret on the top of the boiler, ensuring that the seal is in place. 3. Secure the flue turret on top of the boiler by inserting the open ends of the turret clamp under the 2 studs and fixing it in the middle with the single M5 x 10mm pozihex screw provided. 4. Now make good the inside wall face around the flue. PROCEED TO FRAME Minimiser SE - Installation

19 23 FLUE ASSEMBLY - Exploded view 1. An optional flue duct extension kit is required for wall thicknesses greater than : 460 mm (18") for RHS flue 550 mm (21 1/2") for LHS flue (see Frame 14). 2. When cutting the ducts always use the cardboard support cutting aid provided. 24 WALL MOUNTING TEMPLATE Note. The template shows the positions for the fixing holes and the flue hole centres for standard installation and for using the stand-off brackets. Care MUST be taken to ensure the correct holes are drilled. 1. Separate the templates. 2. Tape both templates into the selected position, locating template B through an extended centre line as shown - ensure that it is the right way up for the flue hand required. 3. Ensure squareness by hanging a plumbline as shown. 4. Mark onto the wall the following: a The two wall mounting plate screw positions (choose one from each group) and the jacking screw position. b. The position of the flue duct hole (see diagram below, and template) Note. Mark the centre of the hole as well as the circumference 5. Remove both templates from the wall. INSTALLATION LEGEND 1. Terminal. 2. Weather seal. 3. Duct assembly. 4. No.8 x 8 self tapping screw. 5. Flue turret. 6. M5 x 10 pozi-hex screw. 7. Turret clamp. 8. Turret seal. SIDE FLUE OUTLET Note. If the boiler is to be fitted flush with 300mm kitchen units using the stand-off brackets ensure the wall is marked to suit this condition (the dotted flue hole outlines on the template). Minimiser SE - Installation 19

20 SIDE FLUE OUTLET 25 PREPARING THE WALL INSTALLATION IMPORTANT. Ensure that, during the cutting operation, masonry falling outside of the building does not cause damage or personal injury. 1. Cut the flue hole (preferably with a 5" core boring tool), ensuring that the hole is square to the wall. Both wall faces immediately around the cut hole should be flat. 2. Drill 3 holes with a 7mm (1/4") masonry drill and insert the plastic plugs, provided, for the wall mounting plate and the jacking screw plate. Note. If the terminal is to be sited within 25-40mm of a corner or vertical pipe (refer to Table 3) then the hole MUST be accurately cut and the rubber weather seal trimmed around the groove provided. The terminal wall plate need not be fitted. 3. Locate 2 of the No.10 x 2" screws in the wall mounting plate (1 at each side, in any of the 3 holes provided at each side) and screw home. 26 CUTTING THE FLUE - For flue lengths 114 to 600mm ONLY 1. The flue cut length is calculated as follows:- a. Measure and note the wall thickness X b. Add dimension H, measured in Frame 24. c. For right hand side flue add 132mm (5 3/ 16") d. For left hand side flue add 48mm (1 7/8") i.e. for RHS X + H + 132mm (5 3/16") for LHS X + H + 48mm (1 7/8") 2. Measure from the groove and cut the tube. 3. To ensure the tube is cut square, mark the flue all the way round. 4. Cut to length, using the cardboard support aid. 5. Remove the cardboard support and remove any burrs. cardboard support cutting aid FOR FLUE LENGTHS GREATER THAN 600mm REFER TO FRAMES 31, 32 & 33 - FLUE EXTENSION DUCTS 27 ASSEMBLING THE FLUE 1. Fit the 'cut to length' flue on to the flue turret. Note. Ensure the groove in the flue aligns with the top of the turret. 2. Drill a 3.2mm dia. hole through the flue via the hole already present in the turret. 3. Secure the turret to the flue, using the self tapping screw provided. 20 Minimiser SE - Installation

21 28 MOUNTING THE BOILER 1. Lift the boiler onto the wall mounting plate, as shown. 2. Check the boiler alignment using a spirit level and adjust as necessary with the jacking screw. 3. Align the hole in the jacking plate with the predrilled hole in the wall and fix in position with the No.10 x 2" screw provided. Note. If the front of the boiler is to be flush with the front of 300mm deep kitchen units then the optional stand-off bracket kit should be used - refer to the fitting instructions supplied with the kit. INSTALLATION 29 CONNECTING THE FLUE TO THE BOILER Note. BEFORE fitting the flue turret, fill the condensate siphon within the boiler by pouring a cupful of water into the flue outlet A. 1. Insert the flue assembly through the prepared hole in the wall far enough to allow the rubber seal to unfold completely and form an adequate seal on the outside wall. SIDE FLUE OUTLET 2. Pull the flue back and locate the flue turret on the top of the boiler, ensuring that the seal is in place. 3. Secure the flue turret on top of the boiler by inserting the open ends of the turret clamp under the 2 studs and fixing it in the middle with the single M5 x 10mm pozi-hex screw provided. 4. Flues over 1 metre long. Fix the flue support bracket to the wall, using the wall plug and wood screw. For standard installations use the short wood screw. If the stand-off option is used, secure the support bracket using the spacer bracket and long wood screw. 5. Now make good the inside wall face around the flue. Minimiser SE - Installation 21

22 INSTALLATION 30 TERMINAL WALL PLATE INSTALLATION This plate allows neat concealment and full compression of the rubber seal. Its use is not essential if the flue hole and flue ducts have been accurately cut and the outside wall face is flat. 1. Position the terminal wall plate over the terminal. 2. Drill 4 fixing holes with a 7mm (1/4") masonry drill. 3. Insert the 4 plastic plugs provided. 4. Secure the plate with 4 of the No.10 x 2" screws provided. Note. If the terminal is less than 2m (6' 6") above ground level, an approved terminal guard should be fitted. Refer to the Flue Installation, Page FLUE EXTENSION DUCTS - For flue lengths greater than 600mm PACK D FLUE EXTENSION DUCT KIT CONTENTS. 32 FLUE EXTENSION DUCTS - continued Use a maximum of 3m extended flue ONLY General arrangement 1. A maximum of 3 extension ducts (one suitably cut) plus the standard flue duct may be used together. 2. Flue extensions of greater length than 1m (39") should be supported with the bracket provided, suitably adjusted - refer to Frame 31. Note. Side flue shown 22 Minimiser SE - Installation

23 33 FITTING THE KIT 1. Remove the cardboard support aid from the flue and place safely to one side. 2. Fit the inner flue extension duct onto the inner flue duct. 3. Fit the outer flue extension duct onto the outer air duct. 4. Drill one 3.2mm (1/8") dia hole through the outer air duct. Do not drill the inner flue duct. 5. Insert the self tapping screw provided to fix the air duct in position. INSTALLATION INSTALLATION 6. Repeat steps 1-5 if a second flue extension is required. 7. Measure and mark the flue length required onto the flue, measuring from the groove near the terminal. 8. To ensure a square cut, mark the flue all the way round. 9. Cut to length using the cardboard support aid. 10. Remove the cardboard off-cut and deburr the metal edges. Appliances fitted with a REAR outlet flue; please refer to Frame 19 Appliances fitted with a SIDE outlet flue; please refer to Frame ELECTRICAL CONNECTIONS WARNING. This appliance MUST be efficiently earthed A mains supply of 230 V ~ 50 Hz is required. The fuse rating should be 3 A. All external controls and wiring MUST be suitable for mains voltage. Wiring should be 3 core PVC insulated cable T LESS than 0.75 mm 2 (24 x 0.2mm) and to BS. 6500, Table 16. Wiring external to the boiler MUST be in accordance with the current I.E.E. (BS.7671) Wiring Regulations and any local regulations. Connection must be made in a way that allows complete isolation of the electrical supply - such as a double pole switch having a 3mm (1/8") contact separation in both poles, or a plug and socket serving only the boiler and system controls. The means of isolation must be accessible to the user after installation. Minimiser SE - Installation 23

24 INSTALLATION 35 INTERNAL WIRING Note. If the programmer kit is to be fitted refer to the instructions provided with the kit, and Frame 36. A pictorial wiring diagram is shown in Frame 37. INSTALLATION 1. Route the mains cable into the bottom RHS rear of the casing. 2. Swing the terminal strip bracket out. 3. Wire the live and neutral into the terminal strip. 4. Connect the earth wire to the earth post. Note. Ensure that the lengths of the current carrying conductors are shorter than the earth conductor so that if the cable slips in its anchorage the current carrying conductors become taut before the earth conductor. Incoming mains wiring detail 5. Secure the mains lead with the cable clamp. 6. Swing the terminal strip bracket back into its working position. Flow wiring diagram LEGEND b - blue bk - black br - brown r - red o - orange w - white y - yellow 36 EXTERNAL WIRING External wiring MUST be in accordance with the current I.E.E. (BS.7671) Wiring Regulations. The wiring diagrams illustrated in Frames 38 to 41 cover the systems most likely to be used with this appliance. For wiring external controls to the Minimiser boiler, reference should be made to the systems wiring diagram supplied by the relevant manufacturer in conjunction with the wiring diagrams shown in Frames 38 to 41. Difficulty in wiring should not arise, providing the following directions are observed: 1. Controls that switch the system on and off, e.g. a time switch, MUST be wired in series, in the live mains lead to the boiler. 2. Controls that override an on/off control, e.g. a frost thermostat, MUST be wired into the mains supply, in parallel, with the controls to be overridden. Refer to Frame If a proprietary system is used, follow the instructions supplied by the manufacturer. 4. The pump must always be wired in parallel with the boiler. 5. SYSTEM DESIGNS FEATURING CONTROLS OR WIRING ARRANGEMENTS WHICH ALLOW THE BOILER TO FIRE WHEN THERE IS PUMPED CIRCULATION TAKING PLACE MUST T BE FITTED. Advice on required modifications to wiring may be obtained from the component manufacturers. 24 Minimiser SE - Installation