AM 213 Installation Introduction

Transcription

1 EAGO Sanitary Ware Co.,Ltd. Factory Add:Shiling Development Zone,Xiaotang Town,Nanhai District,Foshan City,Guangdong,China National Service Hotline: AM 213 Installation Introduction

2 Safety Information 1 Please read carefully and follows all instruction when operating. 2 An earth leakage circuit-breaker must be installed in the power box an please check it carefully before use. 3 To avoid electric shock, the wires replacement must be done by the electrical engineer or the retailer. Please do not change the wires by 2 yourself. The wire shall be 3 1.5mm 4 The earth wire of the water pump and air pump surface must be connected well. The minimum of the copper must be 5 Please do not modify, append or eliminated the product. 6 Please do not use the product after alcohol or drug. 7 The children user shall be closely supervised by parents. 8 All the electrical spare parts except the remote controller must be stable to avoid slip into the bathtub. 9 Warming: the water temperature shall never exceed 60 degree centigrade. 10 Please do not use the strong causticity chemical liquid to clean the product, such as vitriol, hydrochloric acid and lye. 11 Please do not touch the surface of the surface of the power generator when it is running. 12 The water level must be higher than the jets before turning the product on. 13 Please do not drop anything into the pump or power generator connection. 14 Warning: to avoid electrical shock, the GFCI/RCD (Earth leakage circuit Breaker) must be installed. 15. Warning: to avoid electrical shock, please do not use extended wire. The socket must be installed near the product mm 16. Bathtub working conditions: water pressure is MPa, and the ground must have the ability to support the expected loading: AM213 is 550kg. Maintenance Instruction 1. The cleaning of the acrylic surface: The sponge and water could be used for the daily maintenance. If there are scratches appear in the surface, please use the 1500 waterproof abrasive paper to polish the surface. Then use toothpaste to polish again. Also some dirt cleaning machine could be used. However, the strong causticity chemical liquid could not be used fo the cleaning, such as vitriol, hydrochloric acid and lye. 2. Electroplate cleaning: Please use the soft cloth for the cleaning. Please do not use the rough cloth. 3. Suction net cleaning: Turn the screw out and take the suction net out, clean it to keep the water going through smoothly. Please do not use strong the strong causticity chemical liquid could not be used fo the cleaning, such as vitriol, hydrochloric acid and lye. Contents CONTENTS Am AM213 Water and Wire Instruction Diagram 04 Installation Step 05 Wire Connection Diagram for Whirlpool Bathtub 06 Control Panel Usage Instruction Maintenance Record 09 Troubleshooting Instructions

3 AM 213 Components Structure AM 213 Components Structure 1.Bathtub 2. Air pipe 3.PR0105-B401 Control panel A-100 Drain 5.PC board clip 6.PR0105-B401 PC board 7.90 degree elbow 8. AP700 Air pump 9.Stainless steel bracket 10.Adjustable foot 01 Installation Instruction 02

4 AM 213Water and Wire Instruction Diagram 770 Installation Step The product use the standard accessories. Please refer to the production tech parameter and follow the installation step as below: 1.Confirm the product install position 2. Adjust the product to horizontal 3.Connect the water inlet and drain pipe 4.Connect the power 5.Check and confirm 6. Reposition 7.Water testing 1. Confirm the product install position Please refer to the product tech parameter to connect the water inlet pipe, power socket and drain tube, and check if there is enough space for the connection. 2. Adjust the product to horizontal Adjust the adjustable feet of the bathtub to make the product to horizontal. 3. Connect the water inlet and drain pipe The drain pipe is lay in the bottom of the bathtub, with diameter 38mm. The pipe could be elbow and extend easily. Please put the pipe into the drain system and seal it well. Please keep the pipe running through to avoid water exhausted. 4. Connect the power The product is suitable for the required power when purchasing. Please install the power socket according to the tech parameter. Pay attention to the water. Connect the connector plugs into the socket. (Note: the yellow-green-color wire from the water pump is the earth wire, which the diameter is 8mm.) 5. Check and confirm Please check the connection parts are sealed or not after the installation. Clean the dirt in the bathtub and open the drain and then clean the bathtub. In order not to stuff the drain pipe and jets, please clean the dirt before the cleaning. 6. Reposition Reposition the product to the install position. 7. Water testing Confirm the bathtub is clean and close the drain. Start storing the water and check if the bathtub is leak or not. When the water level is higher than the probe, test the control panel function according to the instruction. 03 Installation Instruction 04

5 Wire Connection Diagram for Whirlpool Bathtub PC control panel Bubble Shower Bottom Light Bubble Shower Speed Power ON/OFF Button Control Panel Usage Instruction (AM213) Bubble function instruction: 2. The power of the bubble: weak, middle and strong. 3. Bubble button Bubble shower 泡泡浴 电 箱 Electric cabinet 控制面板 Control panel Turn on the system and press the bubble function and the red light. key to turn on or turn off the Bottom light 水底灯 Water level detector 水位检测器 4. Bubble setting button Turn on the system and the bubble function, press the key Electric parameter Spare part Parameter 电源 Power: :~ V V Rate voltage Massage Pump AC20-240V/50HZ Ozone machine Bottom light DC12V Thermostat Electromagnetism valve AC20V/ 50HZ PC control Speaker Note panel 1 The induced button clicks when valid operation, but there is no response if invalid operation. 1 Power ON/OFF Press the key for more than 1 second to turn on or turn off the system. The control panel would be turned off automatically for each time it is turned on in 60 minutes. The bottom lights would be turned on when the system is turn on. Turn on the power and the light button the red light will be turned on. Press the again to turn off the system. key to set the bubble power among the strong, middle and weak level. Cleaning function instruction Turn off the system and the wait for the water in the bathtub is totally drained. After 10 seconds (it is based on the water level detector which tests if there is no water left in the bathtub in 10 seconds), the air pump will be turned on automatically and blow dry the water left in the bathtub pipes, and it will be turned off automatically after 90 seconds. Rate voltage AC10-120V/60HZ DC12V AC120V/ 60HZ 2. Bottom light Rate power 70W 12W Turn on the system and press the key to turn on or turn off the bottom light and the red light. 05 Installation Instruction 06

6 Maintenance Card Maintenance Card Maintenance Record Model No. Model No. Maintenance Date Maintenance Item Maintenance Unit Maintence person signature Manufacturing Code Tel Purchasing Date Manufacturing Code Customer Name Add Tel. Maintenance item: 1. Every purchase of the series products, get 1 year guarantee by the maintenance service card and purchasing receipt since the purchasing date. The following cases are not covered by the warranty. A. Any damage caused by the misuse, improper maintenance. B. Installation damage by neither the EAGO agent nor appointed installation service organization. C. Without 3 packets "proof, valid bill or proof of purchase. D. Valid card, maintenance card do not match or alternation. E. Damage by the irresistibility and irresistible natural calamities. 2. If it is the product quality problem, it will be free maintenance or change the spare parts. 3. If the problem is not caused by the products itself or over-exceed the one-year guarantee, it will charge the repairing fees and spare parts costs. The first page is kept for the customer. Add. Agent Shop Tel. Purchase Date The second page is sent back to EAGO head office. 07 Installation Instruction 08

7 Troubleshooting Malfunctions 1. Adjust the leg to make the steel 1. The steel stand at bottom stand even. of bathtub is not balance Pieces of screw and 4 shockproof The bathtub 2. The fasten screws for rubbers shall be provided of the motor. shaking and motor and shockproof Fasten the nuts. make noise. rubber is incomplete close. 3. Contact with your dealer or the 3. Problem of motor. manufacturer. The pump is running, but poor jet action. 1. The suction net partly blocked. 2. Not adequate water level. 3. Adjusting valve of function is shut down. 4. The inlet pipe of pump exist air. Causes 5. Other probable cause. Solutions 1. Take off the suction net with screwdriver. Clean it to keep the water going through smoothly. 2. Pour more water until it over flow the senor. 3. Open the adjusting valve of function. 4.a) Open the washout valve to exhaust the air inside the pipe, b) Check and tighten all connection part of the inlet pipe. c) Close the washout valve properly. 5. The water pipe and air pipe may be mixed up. Please contact the professional technician to fix it. MalfunctionsCauses Chrometherapy light doesn t work. Slow water 1. Plug is off. 2. Control circuit board is burnt. 1. Supply water pressure is low. 2. Water inlet block. outlet The filter 1. The rubber ring in the doesn t work filter is damage. No bubble out from the leaking Some water left inside the pipe 1. Air pipe block. 2. Air pump is switch off. pipe because of its special construction. Solutions 1. Check supply water pressure. 2. Clean water inlet filter. 1. Change a new one. 1. Take off the lid of the jet, clean the small air hole by thin wire. 2. Turn on the air pump. Hydro-massage 3. Air pump does not operate. 3. Follow the air pump does not operate jet The pop-up water outlet valve can't pop-up or it is 1. Re-plug in the plug or replace plug. 2. Contact with your dealer or the manufacturer. instruction process to check the air pump. 1. The waste cover is leakage, 1. Take off the stopper of pop-up water the screw is loose or the water outlet valve, fasten the screw or adjust divert adjust too low. the mandril to the proper place. 2. The pulling cord of water 2. Replace with new rubber. outlet is broken. 3. Dismantle the water outlet, level the 3. The washer is uneven. washer and re-install it. Some models of bathtub can not drain all water out from the The massage 1. Voltage is abnormal or motor or the electric power is disconnected. air motor can t 2. The air pressure switch or the be started. micro pneumatic switch is broken 1. Take off the cover of the jet which does not workand clean the air pipe. 2. Turn on the air pump. 3. Check the air pump as the air pump motor failure instruction. 09 Installation Instruction 10