INSTALLATION INSTRUCTION
|
|
- Lambert Fletcher
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTION ELECTRIC HEAT S THRU 05 5 THRU Supersedes: (9) (00) 0-5 FOR SINGLE PACKAGE CONDITIONERS THRU TON SINGLE PACKAGE HEAT PUMPS THRU 5 TON GENERAL This instruction contains all the necessary information for field assembling these CE series electric heaters in the single package units indicated above. These accessories include all of the required hardware except some screws being re-used as indicated in the installation procedure. Table shows the minimum air flow limitations across these heaters. The remaining tables contain important electrical data for the field-installed power supply. Refer to the respective direct-drive or belt-drive table. Units and ductwork are approved for zero clearance to combustible materials equipped with these electric heaters. Depending upon the voltage and the heater rating, some heater accessories require a fuse block and some do not. Refer to the appropriate electrical data table. NOTE: These heater accessories may be installed before or after the unit has been set on a curb or slab. TABLE - FLOW LIMITATIONS TABLE OF CONTENTS General... Installation..., TABLES No. Description Page Airflow Limitations... Direct-Drive Elec. Data & Ton Cooling... Direct-Drive Elec. Data 5& Ton Cooling...5 Direct-Drive Elec. Data & Ton Cooling... 5 Direct-Drive Elec. Data 5 Ton Cooling...7 Direct-Drive Elec. Data & T Heat Pump... 7 Direct-Drive Elec. Data 5 Ton Heat Pump...9 Belt-Drive Elec. Data & Ton Cooling Belt-Drive Elec. Data 5& Ton Cooling... 0 Belt-Drive Elec. Data & Ton Cooling... Belt-Drive Elec. Data 5 Ton Cooling... Belt-Drive Elec. Data & Ton Heat Pump... Belt-Drive Elec. Data 5 Ton Heat Pump...5 FIGURES No. Description Page Blower Partition... Heaters Without A Fuse Box... Heaters With A Fuse Box... NO., NOMINAL 5 MINIMUM CFM,00,0,0,00,0,0,00,0,0,00,0,0,0,0,0 CE000,0 CE00055,00,0,0,0 CE00075,00,0,0,0,00.0,0,0,00,0,0,0,0,0,0,0 CE005,0,0 CE0007,00,0,0,0 CE000,00,0,0,0 CE005,00,0,0,0 CE000,0,0,0,0 CE00,0,0,00,0,0,0,00,0,0,0,0,0,0,0 CE005,0,0 This -ton model is only available as a Single Package Air Conditioner. CGA minimum is,0 CFM.
2 INSTALLATION FOR S WITHOUT A BOX (See Figure ) Refer to the electrical Data Tables for heaters shipped without a fuse box. located on the heating section side of the blower partition. Tighten the nut. NOTE: Wrap the leads with a minimum of layers of electrical tape where they come into contact with the connector. DO NOT tighten the connector clamp screws until the power leads are connected and in place.. Connect the two harnesses having MATE-N-LOCK plugs into their respective sockets located in the blower partition. Refer to Figure. Connector S/P is a two-terminal MATE- N-LOCK. Connector S/P is a four-terminal MATE-N- LOCK. NOTE: The flat surfaces on the pins of the MATE-N-LOCK plugs must align with the flat surfaces on their respective sockets. To remove these plugs after the connections have been made, squeeze the sides together and pull out. 9. Mount the terminal block provided to the holes beneath the M contactor in the unit s main control box using the Phillips pan head screws. FIG. - PARTITION Install the electric heater accessories as follows:. Disconnect all electrical power to the unit.. Remove the following panels from the basic unit. Heating access panel Blower access panel Main control box access panel NOTE: Motor leads are held in place above the blower by plastic ties. Do not disturb these ties unless the leads interfere with panel fit-up.. Remove and discard the cover plate attached to the plenum within the unit heating section. Keep the mounting screws for later use.. Remove knockout from the blower compartment partition. (See Figure ). 0. Remove the -/" knockout from the right side of the unit s main control box. Slip a connector nut and a reducing washer over the power leads from the heater harness and insert the leads into the main control box through the knockout hole. From inside the main control box, slip a reducing washer and an electrical connector over the power leads. Tighten the connector nut, but do not tighten the screws on the connector clamp until the leads have been connected to the terminal block. Refer to the wiring label inside the heater control box cover for the proper connection of the heater power leads. NOTE: Wrap the heater power leads with tape as instructed in "NOTE" under Step 7.. Adjust the heater power leads for the proper slack, and tighten the screws on both connector clamps to secure them in position. Use one of the wire ties provided to cable the heater leads in the heater compartment and two of the wire ties to cable the power leads in the blower compartment.. Connect field power supply wiring to the bottom terminals of the terminal block.. Replace the cover on the heater control box, and reinstall the unit panels that were removed in Step.. Reconnect power to the unit. 5. Remove the cover from the heater accessory control box.. Insert the heater coils through the opening in the heating section plenum. At the same time, insert the heater support pin (on the coil end of heater) into the appropriate hole in the heater support located inside of the plenum. Secure the heater control box to the plenum with seven of the screws that were removed in Step ( screws each side and screw at the bottom). Discard extra screws. CAUTION: Exercise care when inserting the heater into the plenum opening to avoid damage or misalignment of the heater coils. The heater control box must fit flush against the plenum without force and with the control box mounting holes properly aligned. 7. Insert the loose power leads from the heater harness through the knockout hole in the blower partition. An electrical connector is supplied to secure these wires to the panel. Position the connector so that the connector nut is FIG. - S WITHOUT A BOX Unitary Products Group
3 FOR S WITH A BOX (See Figure ) Refer to the Electrical Data Tables for heaters shipped without a fuse box. Install the electric heater accessories as follows:. Disconnect all electrical power to the unit.. Remove the following panels from the basic unit. Heating access panel Blower access panel Main control box access panel NOTE: Motor leads are held in place above the blower by plastic ties. Do not disturb these ties unless the leads interfere with panel fit-up.. Remove and discard the cover plate attached to the plenum within the unit heating section. Keep the mounting screws for later use.. Remove knockout from the blower compartment partition. (See Figure ). 5. Remove the cover from the heater accessory control box.. Insert the heater coils through the opening in the heating section plenum. At the same time, insert the heater support pin (on the coil end of heater) into the appropriate hole in the heater support located inside of the plenum. Secure the heater control box to the plenum with seven of the screws that were removed in Step ( screws each side and screw at the bottom). Discard extra screws. CAUTION: Exercise care when inserting the heater into the plenum opening to avoid damage or misalignment of the heater coils. The heater control box must fit flush against the plenum without force and with the control box mounting holes properly aligned. 7. Insert the loose power leads from the heater harness through the knockout hole in the blower partition. An electrical connector is supplied to secure these wires to the panel. Position the connector so that the connector nut is located on the heating section side of the blower partition. Tighten the nut. be on the blower side of the control box for proper fuse box fit-up. Mount the fuse box inside the blower section. Attach the upper left-hand flange on the fuse box to the back of the main control box with one screw provided. The mounting hole is located above the RC capacitor. Attach the bottom right-hand flange on the fuse box to the unit base, at the holes provided, with two screws. NOTE: If the insulation grip nail fasteners on the base of the blower section interfere with the proper mounting of the fuse box, they should be broken off. CAUTION: Exercise care when securing the fuse box in position to make sure that the evaporator low temperature sensor control leads are not pinched or cut. If leads must be routed away from sheet metal edges, visually check the control to ensure its location has not been disturbed.. Open the hinged fuse box cover to gain access to the inside. Install the electrical connector provided into the knockout hole in the right-hand side of the fuse box and tighten nut. Insert the heat power leads (from Step 7) through the connector in the fuse box and connect to the proper terminals on the fuse block(s). NOTE: Wrap the heater power leads with tape as instructed in "NOTE" under Step 7. Insert the unit power supply leads and the leads from the contactor through the snap bushing (installed in Step 9) in the main control box, and through the open left side of the fuse box to be connected to the fuse block(s). Refer to the wiring label inside the heater control box cover for the proper connection of the power leads.. Adjust all wires for proper slack, and tighten the screws on both connector clamps to secure them in position.. Connect field supply power supply wiring to the lugs on top of the fuse block(s). 5. Close the fuse box cover, replace the cover on the heater control box, and reinstall the unit panels that were removed in Step.. Reconnect power to the unit. NOTE: Wrap the leads with a minimum of layers of electrical tape where they come into contact with the connector. DO NOT tighten the connector clamp screws until the power leads are connected and in place.. Connect the two harnesses having MATE-N-LOCK plugs into their respective sockets located in the blower partition. Refer to Figure. Connector S/P is a two-terminal MATE- N-LOCK. Connector S/P is a four-terminal MATE-N- LOCK. NOTE: The flat surfaces on the pins of the MATE-N-LOCK plugs must align with the flat surfaces on their respective sockets. To remove these plugs after the connections have been made, squeeze the sides together and pull out. 9 Remove the -/" knockout from the right-hand side of the unit s main control box. Insert the special snap bushing provided into the knockout hole from the blower section side of the control box. The retaining collar on the bushing MUST FIG - S WITH A BOX Unitary Products Group
4 TABLE - ELECTRICAL DATA (COOLING W/ DIRECT DRIVE - & TON S) COOLING ELECTRIC S Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on C copper conductors (up to 00 amps max. or 75 C copper conductors. (00 amps and over) Cap FB0 FB05 0/ Volts Volts Unitary Products Group
5 TABLE - ELECTRICAL DATA (COOLING W/DIRECT DRIVE - 5 & TON S) COOLING ELECTRIC S 0 07 CE000 CE000 CE005 CE005 CE00* CE005 CE005 CE005 CE00* CE Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on C copper conductors (up to 00 amps max. or 75 C copper conductors. (00 amps and over) Cap FB0 FB05 0/ Volts Volts Unitary Products Group 5
6 TABLE - ELECTRICAL DATA (COOLING W/ DIRECT DRIVE - & TON S) COOLING ELECTRIC S Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on 75 C copper conductors. Cap FB0 FB05 0/ Volts Volts Unitary Products Group
7 TABLE 5 - ELECTRICAL DATA (COOLING W/DIRECT DRIVE - 5 TON S) COOLING ELECTRIC S 0 CE000 CE000 CE005 CE005 CE00* CE / Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on 75 C copper conductors. Cap FB0 FB05 0/ Volts Volts Unitary Products Group 7
8 TABLE - ELECTRICAL DATA (HEAT PUMP W /DIRECT DRIVE - & TON S) HEAT PUMP ELECTRIC S 0 0 5, Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on C copper conductors (up to 00 amps max. or 75 C copper conductors. (00 amps and over) Cap FB0 FB05 0/ Volts Volts Unitary Products Group
9 TABLE 7 - ELECTRICAL DATA (HEAT PUMP W/ DIRECT DRIVE - 5 TON S) HEAT PUMP ELECTRIC S 0 CE000 CE000 CE005 CE005 CE00* CE Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on C copper conductors (up to 00 amps max. or 75 C copper conductors. (00 amps and over) Cap FB0 FB05 0/ Volts Volts Unitary Products Group 9
10 TABLE - ELECTRICAL DATA - (COOLING w/ BELT DRIVE - & TON S) COOLING ELECTRIC S Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on C copper conductors (up to 00 amps max. or 75 C copper conductors. (00 amps and over) Cap FB0 FB05 0/ Volts Volts 0 Unitary Products Group
11 TABLE 9- ELECTRICAL DATA - (COOLING w/belt DRIVE - 5 & TON S) COOLING ELECTRIC S 0 07 CE005 CE005 CE00* CE005 CE005 CE005 CE00* CE Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on C copper conductors (up to 00 amps max. or 75 C copper conductors. (00 amps and over) Cap FB0 FB05 0/ Volts Volts Unitary Products Group
12 TABLE 0 - ELECTRICAL DATA - (COOLING w/ BELT DRIVE - & TON S) COOLING ELECTRIC S Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on 75 C copper conductors. Cap FB0 FB05 0/ Volts Volts Unitary Products Group
13 TABLE - ELECTRICAL DATA - (COOLING w/belt DRIVE - 5 TON S) COOLING ELECTRIC S 0 CE005 CE005 CE00* CE Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on 75 C copper conductors. Cap FB0 FB05 0/ Volts Volts Unitary Products Group
14 TABLE - ELECTRICAL DATA (HEAT PUMP W/BELT DRIVE - & TON S) HEAT PUMP ELECTRIC S Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on C copper conductors (up to 00 amps max. or 75 C copper conductors. (00 amps and over) Cap FB0 FB05 0/ Volts Volts Unitary Products Group
15 TABLE - ELECTRICAL DATA - (HEAT PUMP w/ BELT DRIVE - 5 TON S) HEAT PUMP ELECTRIC S 0 CE005 CE005 CE00* CE Dual element, time delay type. Standard circuit breakers may be used in Canada and on applications over amps where the heaters are separately fused. Based on C copper conductors (up to 00 amps max. or 75 C copper conductors. (00 amps and over) Cap FB0 FB05 0/ Volts Volts Unitary Products Group 5
16 0/ and -volt models only 0/ and 575-volt models only Subject to change without notice. Printed in U.S.A Copyright by Unitary Products Group 99. All rights reserved. Unitary Products Group 05 York Drive Norman OK 79 Codes: SBY, F, L (00)
ACCESSORY KIT INSTALLATION INSTRUCTIONS
ACCESSORY KIT INSTALLATION INSTRUCTIONS 536306-UAI-B-1009 Electric Heat Accessory 10, 16, 20, 26, 32, 36 & 52kW For Split-System R-410A Air Handling Units Both Air Conditioners and Heat Pumps 7-1/2, 10,
More informationACCESSORY INSTALLATION INSTRUCTION ELECTRIC HEAT ACCESSORY 10, 16, 26, 36 & 72
ACCESSORY INSTALLATION INSTRUCTION ELECTRIC HEAT ACCESSORY, 16, 26, 36 & 72 FOR SPLIT-SYSTEM AIR CONDITIONERS 5, 7-1/2, & 15 TONS SPLIT-SYSTEM HEAT PUMPS 7-1/2 & TONS GENERAL This instruction covers the
More informationGENERAL. Model 2SD UAI-A Before installing read all of the manufacturers installation and maintenance instructions.
ACCESSORY KIT INSTALLATION INSTRUCTION SMOKE DETECTOR KITS, UNIT MOUNT MODELS 2SD04700824, 2SD04700924 AND 2SD04701024 For 3.0 THRU 12.5 TON ROOFTOP UNITS GENERAL Before installing read all of the manufacturers
More informationPAC SERIES - 13 SEER SINGLE PACKAGED AIR CONDITIONER (GEN 3, STYLE A)
www.source1parts.com HVAC SERVICE PARTS PAC SERIES - 13 SEER SINGLE PACKAGED AIR CONDITIONER (GEN 3, STYLE A) Supersedes:035-21137-001 Rev. E (1107) 035-21137-001 Rev. F (0611) 1 of 8 CONDENSER ROOF (SEE
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION MODULAR AIR HANDLER MODEL: N*AH CONTENTS GENERAL... 1 INSPECTION... 2 REFERENCE... 2 LIMITATIONS... 2 LOCATION... 2 BLOWER/COIL ASSEMBLY UPFLOW AND HORIZONTAL INSTALLATIONS...
More informationTechnical Guide SUNLINE 2000 DESCRIPTION ACCESSORIES FIELD INSTALLED SPLIT-SYSTEM EVAPORATOR BLOWER K4EU NOMINAL TONS (WORLD 50 HZ)
Technical Guide SUNLINE 2000 SPLIT-SYSTEM EVAPORATOR BLOWER K4EU180 15 NOMINAL TONS (WORLD 50 HZ) DESCRIPTION These completely assembled units include a well-insulated cabinet, a DX cooling coil with copper
More informationK*ES120 DESCRIPTION TECHNICAL GUIDE SPLIT-SYSTEM EVAPORATOR BLOWERS 10 NOMINAL TONS EER 8.5 ACCESSORIES FIELD INSTALLED TABLE 1: ARI RATINGS*
TECHNICAL GUIDE SPLIT-SYSTEM EVAPORATOR BLOWERS K*ES120 10 NOMINAL TONS EER 8.5 DESCRIPTION These completely assembled dual circuit evaporator blower units include a well-insulated cabinet, a DX cooling
More informationSPLIT-SYSTEM EVAPORATOR BLOWERS K2EU060, K4EU090, K3EU120 & K1EU180 5 Thru 15 Nominal Tons DESCRIPTION ACCESSORIES FIELD INSTALLED
(491) SPLIT-SYSTEM EVAPORATOR BLOWERS K2EU060, K4EU, K3EU & K1EU180 5 Thru 15 Nominal Tons DESCRIPTION These completely assembled units include a well-insulated cabinet, a DX cooling coil with copper tubes
More informationSTELLAR 2000 SINGLE PIECE AIR HANDLERS INSTALLATION INSTRUCTION Supersedes: N2Y (795) N2Y (1195)
STELLAR 2000 SINGLE PIECE AIR HANDLERS INSTALLATION INSTRUCTION Supersedes: 535.02-N2Y (795) 535.02-N2Y (1195) HEAT PUMP MODELS F1RP / F1FP018 thru 060 and COOLING MODELS F1RC / F1FC018 thru 036 035-13620
More informationINSTALLATION INSTRUCTIONS FOR 6536 SERIES TWO TON PACKAGED HEAT PUMP
INSTALLATION INSTRUCTIONS FOR 6536 SERIES TWO TON PACKAGED HEAT PUMP TABLE OF CONTENTS 1. Warnings...2 2. Component Match-Up...2 3. Unit Depiction Figures...3 4. Blower Performance Data...5 5. General
More informationMODELS B1PA024, 030 AND 036
STELLAR 2000 SINGLE PACKAGE HEAT PUMPS INSTALLATION INSTRUCTION Supersedes: 511.26-N1Y (892) 511.26-N1Y (893) MODELS B1PA024, 030 AND 036 035-11622 GENERAL YORK Model B1PA units are factory assembled heat
More informationInstallation Instructions
Installation Instructions EHMA SERIES ELECTRIC HEATERS FOR PAM3 SERIES PACKAGE AIR CONDITIONERS PHM3 SERIES PACKAGE HEAT PUMPS TABLE OF CONTENTS SAFE INSTALLATION REQUIREMENTS... 2 GENERAL INFORMATION...
More informationACCESSORY KIT INSTALLATION MANUAL
ACCESSORY KIT INSTALLATION MANUAL ELECTRIC HEATER ACCESSORY (6HK SERIES) FOR USE WITH MODELS: AP / AE / AVC / AHR / AHE / AHV / MP / ME / MVC / RFCX*E / RFCX*P / PHE / PCE GENERAL INFORMATION WARNING ELECTRICAL
More informationInstallation Instructions
50ZPB, C, 50ZHB, C, PA3Z ---A, PH3Z ---A, PA4Z, PH4Z, PAJ4,PHJ4,WJA4,WJH4 SMALL PACKAGED PRODUCTS (SPP) Accessory Electric Heaters 5---20 kw For 14 SEER, R---410A Manufactured Home Installation Instructions
More informationSPLIT-SYSTEM EVAPORATOR BLOWER DESCRIPTION ACCESSORIES - FIELD INSTALLED. K5EU090 and K4EU Hz 7.5 and 10 NOMINAL TONS SUNLINE 2000 (WORLD 50 HZ)
(994) SPLIT-SYSTEM EVAPORATOR BLOWER K5EU090 and K4EU120 50 Hz 7.5 and 10 NOMINAL TONS SUNLINE 2000 (WORLD 50 HZ) DESCRIPTION These completely assembled units include a well-insulated cabinet, a DX coil
More informationSummer Breeze Heater Service Manual
Summer Breeze Heater Service Manual RSBH RSBH-SB RSBHP Revision: 1.0 Issued: 12-18-2012 Table of Contents I. Basic Assembly and Operation A. Safety Instructions... 2 B. Grounding Instructions... 3 C.
More informationINSTALLATION INSTRUCTIONS FOR 6636 SERIES PACKAGE AIR CONDITIONER
INSTALLATION INSTRUCTIONS FOR 6636 SERIES PACKAGE AIR CONDITIONER TABLE OF CONTENTS 1. Warnings...................................................... 3 2. Component Match-Up...........................................
More informationInstallation Instructions
Electric Heaters 5 --- 20 kw SMALL PACKAGED PRODUCTS (SPP) Accessory Electric Heaters For 13 SEER, R---410A Manufactured Home Installation Instructions NOTE: The Dual Point Kit can only be installed on
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION SINGLE PIECE AIR HANDLERS Supersedes: 535.02-N2V (598) 535.02-N2V (199) HEAT PUMP MODELS F+RP / F+FP018 thru 060 and COOLING MODELS F+RC / F+FC024 thru 036 035-14363 GENERAL This
More informationSPLIT-SYSTEM EVAPORATOR BLOWER DESCRIPTION FEATURES L4EU NOMINAL TONS
036-21096-001 (0101) SPLIT-SYSTEM EVAPORATOR BLOWER L4EU240 20 NOMINAL TONS DESCRIPTION This 20 ton evaporator blower is designed with two distinct modules to provide maximum application flexibility. The
More informationINSTALLATION INSTRUCTIONS FOR SERIES TWO TON HIGH EFFICIENCY PACKAGED HEAT PUMP
RV Products Division INSTALLATION INSTRUCTIONS FOR 46515 SERIES TWO TON HIGH EFFICIENCY PACKAGED HEAT PUMP TABLE OF CONTENTS 1. Warnings.................................................. 2 2. Component
More informationAG Series Electric Heaters
AG Series Electric Heaters Installation, Operation and Maintenance Instructions Internal Auxililary Electric Heat 97B0005N03 Table of Contents Overview 3 Vertical Upflow Installation 4 Horizontal Installation
More informationTechnical Guide DESCRIPTION ACCESSORIES FIELD INSTALLED SPLIT-SYSTEM EVAPORATOR BLOWERS. 7-1/2 and 10 NOMINAL TONS LA090 & LA120 SUPPLY AIR PLENUMS
Technical Guide SPLIT-SYSTEM EVAPORATOR BLOWERS 7-1/2 and 10 NOMINAL TONS LA090 & LA120 DESCRIPTION These completely assembled units include a well-insulated cabinet, a DX cooling coil with copper tubes
More informationSUBMITTAL DATA SHEET FEATURES. SPLIT-SYSTEM EVAPORATOR BLOWERS 7.5, 10, 15 & 20 TONS MODELS: NH-07 thru -20, 2-PIPE NJ-10 thru -20, 4-PIPE
SUBMITTAL DATA SHEET SPLIT-SYSTEM EVAPORATOR BLOWERS 7.5, 10, 15 & 20 TONS MODELS: NH-07 thru -20, 2-PIPE NJ-10 thru -20, 4-PIPE JOB NAME: LOCATION: PURCHASER: ORDER NO: ENGINEER: SUBMITTED TO: FOR: REF:
More informationInstallation Instructions
Electric Heaters 5 --- 20 kw SMALL PACKAGED PRODUCTS (SPP) Accessory Electric Heaters For 13 SEER, R---410A, Z Chassis Installation Instructions NOTE: Read the entire instruction manual before starting
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Electric Heat Sections Used with Blower Coil Units ELECTRIC HEAT SECTIONS 505,084M (0655012-30) 05/15 Supersedes 09/11 Litho U.S.A. NOTICE TO INSTALLER IT IS HIGHLY RECOMMENDED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PACKAGED HEAT PUMP Table of Contents GENERAL INFORMATION.................. 2 VISUALLY INSPECT PRODUCT............... 2 INTRODUCTION........................... 2 OPTIONAL KITS...........................
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PACKAGED HEAT PUMP Table of Contents GENERAL INFORMATION.................. 2 VISUALLY INSPECT PRODUCT............... 2 INTRODUCTION........................... 2 OPTIONAL KITS...........................
More informationINSTALLATION MANUAL AFFINITY SERIES SINGLE PACKAGE AIR CONDITIONERS ELECTRIC/ELECTRIC, AIR-COOLED. MODELS: D1EB036 thru Thru 5 Ton (10 SEER)
INSTALLATION MANUAL CONTENTS GENERAL...................................... 3 INSPECTION.................................... 3 INSTALLATION.................................. 3 REFERENCE....................................
More informationTechnical Guide DESCRIPTION CHAMPION SPLIT-SYSTEM EVAPORATOR BLOWER L4EU240A 20 NOMINAL TONS (WORLD 50 HZ) FEATURES XTG-A-0307
DESCRIPTION Technical Guide CHAMPION SPLIT-SYSTEM EVAPORATOR BLOWER L4EU240A 20 NOMINAL TONS (WORLD 50 HZ) This 20 ton evaporator blower is designed with two distinct modules to provide maximum application
More informationInstallation Instructions
H6HK Series Installation Instructions Electric Heater Kits Installation in Standard and Variable Speed Indoor Air Handlers IMPORTANT: The instructions included with this heater kit are for installations
More informationINSTALLATION INSTRUCTIONS FOR 8330*5511 MOUNTING KIT
RV Products Division INSTALLATION INSTRUCTIONS FOR 8330*5511 MOUNTING KIT 8330-752 CONTROL BOX KIT (12 VDC COOL ONLY) 9330A755 CONTROL BOX KIT (12 VDC HEAT/COOL) 8530-750 CONTROL BOX KIT (24 VAC COOL ONLY)
More informationINSTALLATION INSTRUCTIONS FOR 7330C740 FLUSH MOUNT CEILING ASSEMBLY
INSTALLATION INSTRUCTIONS FOR 7330C740 FLUSH MOUNT CEILING ASSEMBLY TABLE OF CONTENTS Warnings...3 Package Contents...3 General Information...3 Supply Ducting And Registers...3 Routing 115 VAC Wiring...5
More informationMODELS K2EU060A, K4EU090A, & K3EU120A
AIR COOLED SPLIT-SYSTEM AIR CONDITIONERS INSTALLATION INSTRUCTION Supersedes: 550.23-N2Y (589) 550.23-N2Y (399) MODELS K2EU060A, K4EU090A, & K3EU120A 035-16672 GENERAL These completely assembled 5, 7-1/2
More informationTECHNICAL GUIDE VARIABLE SPEED AIR HANDLERS DESCRIPTION FEATURES Rev. A (0105)
TECHNICAL GUIDE VARIALE SPEED AIR HANDLERS FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS MODELS: N1VS 600-2000 CFM LOWERS 2-5 TON COILS OPTIONAL 1 & 3 φ ELECTRIC HEATERS ISO 9001 Certified Quality Management
More informationInstallation Instructions
4 3 Installation Instructions Self Cleaning Free-Standing Electric Range EER2000, EER3000, EER3001, EER3002, JBP10, JBP24, JBP26, JBP30, JBP35, JBP48, JBP64, JBP66, JBP68, JBP69, JBP71, JBP78, JBP80, JBP82,
More informationINSTALLATION MANUAL G*FD SERIES FULL-CASED A COILS UPFLOW/COUNTERFLOW/HORIZONTAL COOLING/HEAT PUMP
INSTALLATION MANUAL G*FD SERIES FULL-CASED A COILS UPFLOW/COUNTERFLOW/HORIZONTAL COOLING/HEAT PUMP MODELS: ORIFICE METERING DEVICE - G*FD024S14 - G*FD060S24 FACTORY INSTALLED TXV - G*FD024S14T - G*FD060S24T
More information1. SAFETY RULES. 8. Avoid placing objects in the path of the blades.
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National
More informationAUXILIARY ELECTRIC HEATER KITS FOR 7.5 AND 10 TON COMMERCIAL AIR HANDLERS
AUXILIARY ELECTRIC HEATER KITS FOR 7.5 AND 10 TON COMMERCIAL AIR HANDLERS WARNING: THIS ACCESSORY IS TO BE INSTALLED BY A QUALIFIED, LICENSED SERVICE PERSON. TO AVOID UN- SATISFACTORY OPERATION OR DAMAGE
More informationJOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30)
P. 1 of 12 JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30) Item: Qty: Description: 1 2 1 x 1 x 5/8 Tee Fitting 2 2 Plastic Snap-in Hose Grommet 3 4 1-1/2" Hose Clamps
More informationMODELS B3CH 048 AND 060 (WORLD 50 HZ)
SUNLINE 2000 SINGLE PACKAGE HEAT PUMPS INSTALLATION INSTRUCTION Supersedes: 5.3-NYI (900)/035-2984-000 035-2984-00-A-0204 MODELS B3CH 048 AND 060 (WORLD 50 HZ) GENERAL YORK Model BCH units are single package
More informationSupersedes: N2Y (498) N2Y (799) MODELS B1HH018 THRU THRU 5 TON (12 SEER)
CHAMPION SERIES SINGLE PACKAGE HEAT PUMPS INSTALLATION INSTRUCTION Supersedes: 511.18-N2Y (8) 511.18-N2Y (7) MODELS B1HH018 THRU 00 1.5 THRU 5 TON (12 SEER) 035-1707-000 GENERAL YORK Model B1HH units are
More informationInstallation in Standard & Variable Speed Indoor Air Handlers IMPORTANT
H6HK Series Electric Heater Kit INSTALLATION INSTRUCTIONS Installation in Standard & Variable Speed Indoor Air Handlers IMPORTANT These instructions are primarily intended to assist qualified individuals
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION SINGLE PIECE AIR HANDLERS Supersedes: 535.02-N2V (600) 535.02-N2U (900) HEAT PUMP MODELS F2RP / F2FP018 thru 060 and COOLING MODELS F2RC / F2FC024 thru 036 035-14520-000 Rev. B
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1964-65 CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE CONTROL
More informationSUNLINE 2000 SINGLE PACKAGE AIR-COOLED AIR CONDITIONERS DESCRIPTION FEATURES
50.TGY (95) SINGLE PACKAGE COOLED CONDITIONERS DCE 0, 0, 00 & DCE 07 0, 0, 00 & 07, AND 5 NOMINAL TONS (0 SEER) AND NOMINAL TONS (9 EER) SHOWN SUNLINE 000 DESCRIPTION YORK Sunline 000 units are convertible
More informationChicagoTM. Instruction Manual. Includes our new CoolTouch TM Control System Looks permanent, but goes wherever you go! U.S.
Includes our new CoolTouch TM Control System Looks permanent, but goes wherever you go! U.S. Patent Pending ChicagoTM A Kichler Decor ceiling fan Kichler Lighting 7711 East Pleasant Valley Road P.O. Box
More informationInstallation Instructions
Electric Heater Kit For use with GB, GP and GT eries Geothermal Heat Pumps KWAEH0101N05 KWAEH0101N10 KWAEH0101F15 KWAEH0101F20 Installation Instructions NOTE: Read the entire instruction manual before
More informationINSTALLATION MANUAL G*FD SERIES FULL-CASED A COILS UPFLOW/COUNTERFLOW/HORIZONTAL COOLING/HEAT PUMP MODELS: TABLE OF CONTENTS LIST OF FIGURES
INSTALLATION MANUAL G*FD SERIES FULL-CASED A COILS UPFLOW/COUNTERFLOW/HORIZONTAL COOLING/HEAT PUMP MODELS: ORIFICE METERING DEVICE - G*FD024S14 - G*FD060S24 FACTORY INSTALLED TXV - G*FD024S14T - G*FD060S24T
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS T CLASS TSA Series 6 to 20 Ton AIR CONDITIONERS 6 20 TONS 506147 01 06/11 Supersedes 3/11 Litho U.S.A. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE IMPORTANT The Clean Air Act
More informationProduct Data. FH4A Fan Unit. Sizes 001 thru 004
Product Data FH4A Fan Unit Sizes 00 thru 004 Air Handling Technology At Its Finest Reliability, dependability, and great value are built into the FH4A fan units. The unit is compact and easy to install,
More informationViking Installation Guide
Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at
More informationACCESSORY KIT INSTALLATION INSTRUCTIONS
ACCESSORY KIT INSTALLATION INSTRUCTIONS HOT WATER AND STEAM COIL ACCESSORIES MODELS 1HW0410, 0411, 0412 and 1NF0456, 0457, 0458 For 7.5 Thru Ton Generation 2 Split System Indoor Units 643960-UAI-A-0910
More informationINSTALLATION INSTRUCTIONS FOR 6532 SERIES PACKAGE HEAT PUMP
INSTALLATION INSTRUCTIONS FOR 6532 SERIES PACKAGE HEAT PUMP RV Products A Division of Airxcel, Inc. P.O. Box 4020 Wichita, KS 67204 1976-360 (1-02) PP TABLE OF CONTENTS 1. Warnings......................................................
More informationInstallation Instructions
50ES---A, 50EZ---A, 50VL---A, 50VG---A, 50VR---A, 50VT---A, 604D--- ---A, 607C--- ---A, 607E,--- ---A, 704D--- ---A, 707C--- ---A, 707E--- ---A PA3G --- --- A, PH3G --- --- A SMALL PACKAGED PRODUCTS Electric
More information1. SAFETY RULES. 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning.
Kichler Basics 403 1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance
More informationIMPORTANT INSTRUCTIONS - OPERATING MANUAL
IMPORTANT INSTRUCTIONS - OPERATING MANUAL Models: AK80LSL, AK100LSL Exhaust Fan READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
More informationCEILING FAN OWNER'S MANUAL
CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODELS: 52-ECM-5RV-13 52-ECM-5RV- 52-ECM-5RV-SN FAN RATING AC 120V. 60Hz CUL LISTED MODEL : AC-552 1. TOOLS AND MATERIALS REQUIRED Philips screwdriver
More informationInstallation Instructions
Installation Instructions PAM3 SERIES PACKAGE AIR CONDITIONERS TABLE OF CONTENTS SAFETY LABELING AND SIGNAL WORDS... 2 UNIT DIMENSIONS... 3 SAFE INSTALLATION REQUIREMENTS... 3 LOCATING THE UNIT... 3 CLEARANCES...
More informationInstallation Instructions
50ES--A, 50EZ--A, 50VG--A, B, 50VL--A, B, 50VR--A, 50VT--A, B 604D-- --A, 607C-- --A, B, 607E-- --A, 704D-- --A, 707C-- --A, B, 707E-- --A PA3G -- -- A, PH3G -- -- A, PA4G, PH4G PAD3, PHD3, PAD4, PHD4,
More informationREAD AND SAVE THESE INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS CEILING FAN INSTALLATION AND OPERATION INSTRUCTION FAN RATING AC 120V. 60Hz UL LISTED MODEL: AC-552OD WEIGHT OF FAN: 6.82 KGS 1. TOOLS AND MATERIALS REQUIRED Philips screw
More informationReplacement Parts List
Replacement Parts List SINGLE PACKAGE AIR CONDITIONER GENERATION 4 42 CABINET DS-07 COMPRESSORS 1 1 Compressor, H20J403DBLA 015-03652-001 2 - - 1 1 Compressor, H20J403DBEA 015-03682-001-2 - 1 1 Compressor,
More informationInstallation Instructions
Electric Heaters 5 --- 20 kw Installation Instructions SMALL PACKAGED PRODUCTS 2to5Tons Accessory Electric Heaters (Single---Point Connection) NOTE: Read the entire instruction manual before starting the
More informationSUNLINE SERIES SINGLE PACKAGE AIR CONDITIONERS. INSTALLATION INSTRUCTION Supersedes: Nothing N3Y (394) MODELS D*SC360 & 480 INSPECTION
SUNLINE SERIES SINGLE PACKAGE AIR CONDITIONERS INSTALLATION INSTRUCTION Supersedes: Nothing 530.25-N3Y (394) MODELS D*SC360 & 480 035-11820 208/230/575 VOLT ONLY 208/230/460 VOLT ONLY GENERAL This instruction
More informationInstallation Instructions
Electric Heater Packages Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY CONSIDERATIONS Installing and servicing of heating and air conditioning
More informationHatteras BayTM. Patio. Instruction Manual. Includes our new CoolTouch TM Control System Looks permanent, but goes wherever you go! U.S.
Hatteras BayTM Patio A Kichler Décor ceiling fan Designed to coordinate with a popular Kichler Lighting collection. Includes our new CoolTouch TM Control System Looks permanent, but goes wherever you go!
More informationSERVICE MANUAL FOR 6636A & 6636B SERIES TWO TON HIGH EFFICIENCY PACKAGED AIR CONDITIONERS
SERVICE MANUAL FOR 6636A & 6636B SERIES TWO TON HIGH EFFICIENCY PACKAGED AIR CONDITIONERS TABLE OF CONTENTS 1. Warnings & Component Match-Up............................................ 2 2. Unit Specifications..........................................................
More informationReplacement Parts List
Replacement Parts List SINGLE PACKAGE AIR CONDITIONER GENERATION 4 42 CABINET Note: This is a non-comprehensive parts list intended for stocking purposes for first production (style A) units based on current
More informationDDYZ SERIES - 13 SEER SINGLE PACKAGED GAS/ELECTRIC AIR CONDITIONER (R-410A, STYLE A,B)
www.source1parts.com HVAC SERVICE PARTS DDYZ SERIES - 13 SEER SINGLE PACKAGED GAS/ELECTRIC AIR CONDITIONER (R-410A, STYLE A,B) Supersedes:035-23383-001 Rev. A (1211) 035-23383-001 Rev. B (0112) 1 of 14
More informationProduct Data. FH4A Fan Unit. Sizes 001 thru 004
Product Data FH4A Fan Unit Sizes 001 thru 004 Air Handling Technology At Its Finest Reliability, dependability, and great value are built into the FH4A fan units. The unit is compact and easy to install,
More informationOrrin. Instruction Manual. Includes our new CoolTouch TM Control System Looks permanent, but goes wherever you go! U.S.
Includes our new CoolTouch TM Control System Looks permanent, but goes wherever you go! U.S. Patent Pending Orrin A Kichler Select ceiling fan Kichler Lighting 7711 East Pleasant Valley Road P.O. Box 318010
More informationSM Field Installed Electric Heat Kit
SM Field Installed Electric Heat Kit HK050 HK100 HK150 HK200 Installation Manual 8733822029 (2018/07) US 2 SM Series Electric Heat Installation Manual Data subject to change 07.2018 8733822029 Installation
More informationSAVE THESE INSTRUCTIONS
Built-In Dishwasher Dishwashers Write the model and serial numbers here: Model # Serial # You can find them on the tub wall just inside the door or. the lower part of back. Installation Instructions DDW1802W
More informationInstallation Instructions
Electric Heater Packages Installation Instructions TE: Read the entire instruction manual before starting the installation. SAFETY CONSIDERATIONS Installing and servicing of heating and air conditioning
More informationINSTALLATION INSTRUCTIONS FOR 6797A737 HEAT PUMP FLUSH MOUNT CEILING PLENUM
INSTALLATION INSTRUCTIONS FOR 6797A737 HEAT PUMP FLUSH MOUNT CEILING PLENUM TABLE OF CONTENTS Warnings............................................................................... 2 Package Contents........................................................................
More informationSUNLINE 2000 ELECTRIC / ELECTRIC SINGLE PACKAGE AIR CONDITIONERS INSTALLATION INSTRUCTION Supersedes: N7Y (993) 530.
SUNLINE 00 ELECTRIC / ELECTRIC SINGLE PACKAGE AIR CONDITIONERS INSTALLATION INSTRUCTION Supersedes: 530.18N7Y (993) 530.18N7Y (295) MODELS D3CE 036, 048 & 060 ( SEER) MODEL D1CE 072 (9 EER) (STYLE B &
More informationINSTALLATION MANUAL UN-CASED A COILS UPFLOW FOR COOLING/HEAT PUMPS FLEX COILS FOR FIELD INSTALLED TXV MODELS: UC LIST OF SECTIONS LIST OF FIGURES
INSTALLATION MANUAL UN-CASED A COILS UPFLOW FOR COOLING/HEAT PUMPS FLEX COILS FOR FIELD INSTALLED TXV MODELS: UC ISO 9001 Certified Quality Management System SAFETY................................................
More informationINSTALLATION INSTRUCTIONS FOR MOUNTING KIT
RV Products Division INSTALLATION INSTRUCTIONS FOR 8330-5501 MOUNTING KIT 8330-752 CONTROL BOX KIT (12 VDC COOL ONLY) 9330B755 CONTROL BOX KIT (12 VDC HEAT/COOL) 8530-750 CONTROL BOX KIT (24 VAC COOL ONLY)
More informationINSTALLATION MANUAL (AIR COOLED) SPLIT-SYSTEM AIR CONDITIONER MODEL: LA120 NOTES, CAUTIONS AND WARNINGS SAVE THIS MANUAL B-0203
INSTALLATION MANUAL (AIR COOLED) SPLIT-SYSTEM AIR CONDITIONER CONTENTS NOMENCLATURE............................. 3 GENERAL.................................... 4 SAFETY CONSIDERATIONS.....................
More informationValkyrieTM. Instruction Manual. Includes our new CoolTouch TM 6 Speed DC Control System Looks permanent, but goes wherever you go! U.S.
ValkyrieTM A Kichler Décor ceiling fan Designed to coordinate with a popular Kichler Lighting collection. Includes our new CoolTouch TM 6 Speed DC Control System Looks permanent, but goes wherever you
More informationCircoloTM A Kichler Décor ceiling fan Designed to coordinate with a popular Kichler Lighting collection.
CircoloTM A Kichler Décor ceiling fan Designed to coordinate with a popular Kichler Lighting collection. Includes our new CoolTouch TM Control System Looks permanent, but goes wherever you go! U.S. Patent
More informationINSTALLATION INSTRUCTIONS FOR 8330*633* COOL ONLY A/C 8330*635* HEAT READY A/C 8530*63** HEAT PUMP CHILLGRILLE FLUSH MOUNT CEILING ASSEMBLY
RV Products Division INSTALLATION INSTRUCTIONS FOR 8330*633* COOL ONLY A/C 8330*635* HEAT READY A/C 8530*63** HEAT PUMP CHILLGRILLE FLUSH MOUNT CEILING ASSEMBLY DESIGNED AND MANUFACTURED BY THE MAKERS
More information60" Hatteras BayTM. Patio. Instruction Manual. Includes our new Wall Control System. A Kichler Décor ceiling fan
Includes our new Wall Control System 60" Hatteras BayTM Patio A Kichler Décor ceiling fan Kichler Lighting 7711 East Pleasant Valley Road P.O. Box 318010 Cleveland, Ohio 44131-8010 Customer Service 866.558.5706
More informationInstallation Instructions
EHNA Electric Heaters 5-20kW For 60 Hz Small Packaged Products MODELS: PAD3, PHD3, PAD4, PHD4, PAD5, PHD5, WPA3, WPH3 Installation Instructions NOTE: Read the entire instruction manual before starting
More informationInstallation Instructions
Installation Instructions Electric Heater Packages KFAEH -CIRCUIT GROUND LUG TERMINAL BLOCK MULTI-CIRCUIT GROUND LUG COOLING CONTROL PLATE ADAPTER PLATE (MUST BE REMOVED WHEN INSTALLING LARGE HEATER) BLOCK
More informationCEILING FAN OWNER'S MANUAL
CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODEL: 52-854-5RV-234 52-854-5RV-CH 52-854-5RV- FAN RATING AC 120V. 60Hz CUL LISTED MODEL : AG-962MC 1. TOOLS AND MATERIALS REQUIRED Philips
More informationEMBASSY SERIES SINGLE PACKAGE AIR CONDITIONERS (WATER-COOLED) C2ED060, 090, 120 & 180 5, 7-1/2, 10 & 15 Nominal Tons
560.20-TG1Y (388) EMBASSY SERIES SINGLE PACKAGE AIR CONDITIONERS (WATER-COOLED) C2ED060, 090, 120 & 180 5, 7-1/2, 10 & 15 Nominal Tons Each circuit includes a fully hermetic compressor with a crankcase
More informationMERIT SERIES Up Flow / Horizontal
A I R H A N D L E R S CB26UH / CBX26UH MERIT SERIES Up Flow / Horizontal E N G I N E E R I N G D A T A Bulletin No. 210429 December 2006 Supersedes November 2006 Nominal Capacity 1.5 to 5 Tons Optional
More informationInstallation Instructions
NAHB00501WK Twinning Kit for HSI Single-Stage Condensing and Non-Condensing Gas Furnaces Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY CONSIDERATIONS
More informationInnes. Instruction Manual A Kichler Decor ceiling fan. Includes our new TM
Innes 300130 A Kichler Decor ceiling fan Includes our new CoolTouch Control System Looks permanent, but goes wherever you go! U.S. Patent Pending Kichler Lighting 7711 East Pleasant Valley Road P.O. Box
More informationIMPORTANT CB26UH CBX26UH. Service Literature. CB26UH and CBX26UH Series Table of Contents. Model Number Information... 2
Service Literature Corp. 0527 L10 Revised May 2011 CB26UH and CBX26UH Series Table of Contents CB26UH CBX26UH Model Number Information................... 2 Specifications / Electrical Data................
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Models MB08B1500A2 MB12F1900A2 MB16J2200A2 MB20N2600A2 Contents 115 Volt General Information / Installation... 2 Installations... 3 Horizontal Installations... 3 Ductwork Connections...
More informationSunburst. Instruction Manual. Includes our new Wall Control System. A Kichler Décor ceiling fan
Includes our new Wall Control System Sunburst A Kichler Décor ceiling fan Kichler Lighting 7711 East Pleasant Valley Road P.O. Box 318010 Cleveland, Ohio 44131-8010 Customer Service 866.558.5706 8:30 AM
More informationCHAMPION SPLIT-SYSTEM EVAPORATOR BLOWER DESCRIPTION FEATURES L2EU NOMINAL TONS
550.23-TG5Y (893) CHAMPION SPLIT-SYSTEM EVAPORATOR BLOWER L2EU240 20 NOMINAL TONS DESCRIPTION This 20 ton evaporator blower is designed with two distinct modules to provide maximum application flexibility.
More informationINSTALLATION INSTRUCTIONS FOR 7370A736 FLUSH MOUNT CEILING PLENUM
INSTALLATION INSTRUCTIONS FOR 7370A736 FLUSH MOUNT CEILING PLENUM TABLE OF CONTENTS Warnings...2 Package Contents...2 General Information...3 Ceiling Plenum Installation Requirement...3 Supply Ducting
More information21 TRV Blower Installation Instructions
INSTALL THE ACCENT LIGHT BEFORE THE BLOWER (IF APPLICABLE) If installing the accent light, install it first, leaving the control cover loose for blower rheostat installation. THE BLOWER IS MUCH EASIER
More informationSPLIT-SYSTEM EVAPORATOR BLOWER (AIR COOLED) INSTALLATION INSTRUCTION Supersedes: Nothing N4C-0500
SPLIT-SYSTEM EVAPORATOR BLOWER (AIR COOLED) INSTALLATION INSTRUCTION Supersedes: Nothing 550.23-N4C-0500 MODEL L*BC240 035-16603 GENERAL This 20 ton evaporator blower is designed with two distinct modules
More informationMERIT Series R-410A - Upflow / Horizontal
PRODUCT SPECIFICATIONS AIR HANDLERS CBX5UH (-0) MERIT Series R-0A - Upflow / Horizontal Bulletin No. 060 March 05 Supersedes November 0 Nominal Capacity -.5 to 5 Tons Optional Electric Heat -.5 to 0 kw
More informationINSTALLATION INSTRUCTIONS FOR 8330*63**, 8530*63** CHILLGRILLE FLUSH MOUNT CEILING ASSEMBLY
RV Products Division INSTALLATION INSTRUCTIONS FOR 8330*63**, 8530*63** CHILLGRILLE FLUSH MOUNT CEILING ASSEMBLY DESIGNED AND MANUFACTURED BY THE MAKERS OF COLEMAN -MACH AIR CONDITIONERS TABLE OF CONTENTS
More informationCEILING FAN OWNER'S MANUAL
CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODEL: 52-135-5WA-13 FAN RATING AC 120V. 60Hz CUL LISTED MODEL : AC-552OD 1. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver
More information