O.D / 2" (444) 15 1 / 2 " (393) Maximum I.D / 4 " (336) 1 3 / 4 " (45) 1 1 / 4 " (32)

Transcription

1 standard basin 100 Specifications Standard Round Basin with Overflow Item No. 100 For Undercounter Mount Installation Recommended openings for Under Counter mounting: Min. Diameter: 13 1 / 4 (337). Diameter: 15 1 / 2 (394) Available with or without overflow. See Hardware pg B.1.8 to order Round Overflow, Item number 911.xx as a separate item with choice of metal finish. See page 1.1.d for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. O.D / 2" (444) 15 1 / 2 " (393) imum 1 / 8 " (3) max min I.D / 4 " (336) 1 1 / 16 " (27) 3 / 8 " (10) 1 1 / 8 " (29) 6" (152) 6 9 / 16 " (166) Round Overflow item 911.xx 1 3 / 4 " (45) (203) 1 1 / 4 " (32) Drain fitting not provided, unless specified I.D / 4 " (336) O.D / 2 " (444)

2 standard basin 100 Specifications Standard Round Basin without Overflow Item No. 100 For Undercounter Mount Installation Recommended openings for Under Counter mounting: Min. Diameter: 13 1 / 4 (337). Diameter: 15 1 / 2 (394) Available with or without overflow. For Basins ordered without Overflow, Drain Collar is required to install drain. See Hardware pg B.1.7 to order required Drain Collar, Item number 900.xx as a separate item with choice of metal finish. See page 1.1.d for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. O.D / 2 " (444) 15 1 / 2 " (393) imum 1 / 8 " (3) max min I.D / 4 " (336) 6" (152) 6 9 / 16 " (166) 1 3 / 4 " (45) (203) Drain Collar item 900.xx 1 1 / 4 " (32) Drain fitting not provided, unless specified I.D / 4 " (336) O.D / 2 " (444)

3 standard basin 101 Specifications Standard Round Basin with Overflow Item No. 101 For Drop-in Installation Drop-in installation is accomplished by using a self-adhesive silicone gasket applied during installation to a special groove in the flange of the bowl. Gasket is not required for Drop-in installation on some color and finish combinations. See page Colors & Finishes Guide for these choices. Order Item number 100 for any of these color and finish combinations. *Available with or without overflow. Overflow is not recommended. Counter may need to be notched to accommodate Overflow, use maximum cut-out size. See Hardware pg B.1.8 to order Round Overflow, Item number 911.xx as a separate item with choice of metal finish. See page 1.1.e for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. O.D / 2" (444) imum Counter Cut-out 16 1 / 2" (423) Dia. Minimum Counter Cut-out 16" (410) Dia. 1 / (3) I.D / 4" (336) 3 / 4" (19) Minimum Opening16" (624mm) Dia. 1 1 / 16 " (27) 3 / 8 " (10) 1 1 / 8 " (29) imum Opening16 1 /2" (644mm) Dia. 6" (152) 1 3 / 4" (45) 6 9 / 16" (166) Round Overflow item 911.xx (203) I.D / 4" (336) O.D / 2" (444) Recommended Cut-out sizes: imum Counter Cut-out 16 1/2" (423) Dia. Minimum Counter Cut-out 16" (410) Dia.

4 standard basin 101 Specifications Standard Round Basin without Overflow Item No. 101 For Drop-in Installation Drop-in installation is accomplished by using a self-adhesive silicone gasket applied during installation to a special groove in the flange of the bowl. Gasket is not required for Drop-in installation on some color and finish combinations. See page Color & Finish Guide for these choices. Order Item number 100 for any of these color and finish combinations. Available with or without overflow. For Basins ordered without Overflow, Drain Collar is required to install drain. See Hardware pg B.1.7 to order Drain Collar, Item number 900.xx as a separate item with choice of metal finish. See page 1.1.e for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. O.D / 2" (444) imum Counter Cut-out 16 1 / 2" (423) Dia. Minimum Counter Cut-out 16" (410) Dia. 1 / (3) I.D / 4" (336) 3 / 4" (19) imum Opening 16 1 /2" (644mm) Dia. Minimum Opening 16" (624mm) Dia. 6" (152) 1 3 / 4" (45) 6 9 / 16" (166) (203) Drain Collar item 900.xx I.D / 4" (336) O.D / 2" (444) Recommended Cut-out sizes: imum Counter Cut-out 16 1/2" (423) Dia. Minimum Counter Cut-out 16" (410) Dia.

5 standard basin 150 Specifications Standard Oval Basin with Overflow Item No. 150 For Undercounter Mount Installation Recommended openings for Under Counter mounting: : 18 3 / 4 (476) x 14 1 / 4 (362) Med: 17 1 / 4 (438) x 12 3 / 4 (324) Min: 16 1 / 2 (419) x 12 (305) Available with or without Overflow. See Hardware pg B.1.8 to order Oval Overflow, Item number 916.xx as a separate item with choice of metal finish. See page 1.1.d for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. max min Short Section Long Section 1 1 / 16" (27) 3 / 8 " (10) 1 1 / 8 " (29) 1 / 8 " (6) 6" (152) Oval Overflow item 916.xx 1 3 / 4 " (45) 6 9 / 16 " (167) (203) 16 1 / 4 " (412) 11 3 / 4 " (301) I.D / 4 " (404) O.D / 4 " (527)

6 standard basin 150 Specifications Standard Oval Basin without Overflow Item No. 150 For Undercounter Mount Installation Recommended openings for Under Counter mounting: : 18 3 / 4 (476) x 14 1 / 4 (362) Med: 17 1 / 4 (438) x 12 3 / 4 (324) Min: 16 1 / 2 (419) x 12 (305) Available with or without Overflow. For basins ordered without Overflow, Overflow Collar is required to install drain. See Hardware pg B.1.7 to order Drain Collar, Item number 900.xx as a separate item with choice of metal finish. See page 1.1.d for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. max min Short Section Long Section 1 1 / 16 " (27) 3 / 8 " (10) 1 / 8 " (6) 6" (152) 1 3 / 4 " (45) 6 9 / 16 " (167) (203) Drain Collar item 900.xx 1 1 / 4 " (32) 16 1 / 4 " (412) 11 3 / 4 " (301) I.D / 4 " (404) O.D / 4 " (527)

7 standard basin 151 Specifications Standard Oval Basin with Overflow Item No. 151 For Drop-in Installation Drop-in installation is accomplished by using a self-adhesive silicone gasket applied during installation to a special groove in the flange of the bowl. Gasket is not required for Drop-in installation on some color and finish combinations. See page Colors & Finish Guide for these choices. Order Item number 150 for any of these color and finish combinations. Available with or without overflow. Overflow is not recommended. Counter may need to be notched to accommodate Overflow, use maximum cut-out size. See Hardware pg B.1.8 to order Oval Overflow, Item number 916.xx as a separate item with choice of metal finish. See page 1.1.e for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. Short Section. Short Section Cut-out 15 1 / 4" (391) Min. Short Section Cut-out 14 3 / 4" (378) Long Section. Long Section Cut-out 19 3 / 4" (506) Min. Long Section Cut-out 19 1 / 4" (494) 3 / 4" (19) 3 / (10) 1 1 / (29) 6" (152) Overflow item 916.xx 1 3 / 4" (45) 6 9 / 16" (166) (203) 16 1 / 4" (412) 11 3 / 4" (301) 15 3 / 4" (404) 20 3 / 4" (527) Recommended Cut-out sizes:. Cut-out 15 1 / 4" (391) x 19 3 / 4" (506) Min. Cut-out 14 3 / 4" (378) x 19 1 / 4" (494)

8 standard basin 151 Specifications Standard Oval Basin without Overflow Item No. 151 For Drop-in Installation Drop-in installation is accomplished by using a self-adhesive silicone gasket applied during installation to a special groove in the flange of the bowl. Gasket is not required for Drop-in installation on some color and finish combinations. See page Color & Finish Guide for these choices. Order Item number 150 for any of these color and finish combinations. Available with or without overflow. For Basins ordered without Overflow, Drain Collar is required to install drain. See Hardware pg B.1.7 to order Drain Collar, Item number 911.xx as a separate item with choice of metal finish. See page 1.1.e for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. Short Section. Short Section Cut-out 15 1 / 4 " (391) Min. Short Section Cut-out 14 3 / 4 " (378) Long Section. Long Section Cut-out 19 3 / 4 " (506) Min. Long Section Cut-out 19 1 / 4 " (494) 6" (152) 1 3 / 4 " (45) 6 9 / 16 " (166) (203) Drain Collar item 900.xx 1 1 / 4 " (32) 16 1 / 4 " (412) 11 3 / 4 " (301) 15 3 / 4 " (404) 20 3 / 4 " (527) Recommended Cut-out sizes:. Cut-out 15 1 / 4 " (391) x 19 3 / 4 " (506) Min. Cut-out 14 3 / 4 " (378) x 19 1 / 4 " (494)

9 standard basin 170 Specifications Standard Rectangular Basin with Overflow Item No. 170 For Undercounter Mount Installation Recommended cut-out for Under Counter mounting: imum 22 1/2 (571) x 16 1/2 (419) Minimum 20 1/2 (520) x 14 1/2 (368) 1 (456) Available wtih or without overflow See Hardware pg B.1.8 to order Rectangular Overflow, Item number 918.xx as a separate item with choice of metal finish. See page 1.1.f for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. 24" (608) Long Section 24" (608) Outside 22 1 / 2" (571) Cut-out imum 21 1 / 2" (546) Cut-out Minimum 3 / 4" (19) 1 3 / 4" (45) 3 7 / (98) 4 1 / 2" (114) 3 / Front view of Rectangular Overflow item 918.xx Short Section 1 (456) Outside 16 1 / 2" (419) Cut-out imum 15 1 / 2" (394) Cut-out Minimum 1 1 / (29) 3 / 4" (19) 1 3 / 4" (45) Rectangular Overflow Item 918.xx 3 7 / (98) 4 1 / 2" (114)

10 standard basin 170 Specifications Standard Rectangular Basin without Overflow Item No. 170 For Undercounter Mount Installation Recommended cut-out for Under Counter mounting: imum 22 1/2 (571) x 16 1/2 (419) Minimum 20 1/2 (520) x 14 1/2 (368) 1 (456) Available wtih or without overflow For Basins without Overflow, Overflow Collar is required to install drain See Hardware pg B.1.7 to order Drain Collar, Item number 900.xx as a separate item with choice of metal finish. See page 1.1.f for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. 24" (608) Long Section 24" (608) Outside 22 1 / 2" (571) Cut-out imum 21 1 / 2" (546) Cut-out Minimum 3 / 4" (19) 1 3 / 4" (45) 3 7 / (98) 4 1 / 2" (114) Drain Collar item 900.xx Short Section 1 (456) Outside 16 1 / 2" (419) Cut-out imum 15 1 / 2" (394) Cut-out Minimum 3 / 4" (19) 1 3 / 4" (45) 3 7 / (98) 4 1 / 2" (114) Drain Collar item 900.xx Rectangular Standard Basin Item No (456)

11 standard basin 171 Specifications Standard Rectangular Basin with Overflow Item No. 171 For Drop-in Installation Recommended cut-out for Drop-in mounting: 16-1/2 (419) x 20-1/2 (571) Drop-in installations for the 171 Basin are accomplished without a gasket and are available only in limited color and finish combinations. See page Color & Finish Guide for these choices. 1 (456) Available with or without overflow. See Hardware pg B.1.8 to order Rectangular Overflow, Item number 918.xx as a separate item with choice of metal finish. See page 1.1.f for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. 24" (608) Long Section 24" (608) Outside 22 1 / 2" (571) Cut-out 3 / 4" (19) 1 3 / 4" (45) 3 7 / (98) 4 1 / 2" (114) Front view of Rectangular Overflow Item 918.xx Short Section 1 (456) Outside 16 1 / 2" (419) Cut-out Rectangular Overflow Item 918.xx 1 1 / (29) 1 3 / 4" (45) 3 7 / (98) 4 1 / 2" (114)

12 standard basin 171 Specifications Standard Rectangular Basin without Overflow Item No. 171 For Drop-in Installation Recommended cut-out for Drop-in mounting: 16-1/2 (419) x 20-1/2 (571) Drop-in installations for the 171 Basin are accomplished without a gasket and are available only in limited color and finish combinations. See page Color & Finish Guide for these choices. 1 (456) Available with or without overflow. For Basins ordered without Overflow, Drain Collar is required to install a drain fitting. See Hardware pg B.1.7 to order Drain Collar, Item number 900.xx as a separate item with choice of metal finish. 24" (608) See page 1.1.f for general ADA guidelines. Contact factory for installation of this product to meet ADA guidelines in coordination with your faucet specification. Long Section 24" (608) Outside 22 1 / 2" (571) Cut-out 3 / 4" (19) 1 3 / 4" (45) 3 7 / (98) 4 1 / 2" (114) Drain Collar item 900.xx Short Section 1 (456) Outside 16 1 / 2" (419) Cut-out 1 3 / 4" (45) 3 7 / (98) 4 1 / 2" (114) Drain Collar item 900.xx

13 standard basin Installation Instructions 1.1.a Rough-in Specification For Undermount and Drop-in Installations Basins Item No. 100, 101, 150, 151, 170 & 171 Please provide these instructions to contractor at point of sale. Rough-in for waste: Round and Oval Basins Drawings below show recommended height of waste rough-in for all Vitraform Drain systems. If additional distance is required, see pgs B for maximum rough-in dimensions of individual drains. Rough-in for waste: Rectangular Basins Drawings below show recommended height of waste rough-in for all Vitraform Drain systems. If additional distance is required, see pgs B for maximum rough-in dimensions of individual drains. P Trap P Trap 12" (305) 10" (254) The compression fitting should not extend more than 5 / (16) beyond the finished wall in order to be covered by the Vitraform escutcheon. The compression fitting should not extend more than 5 / (16) beyond the finished wall in order to be covered by the Vitraform escutcheon. European Siphon European Siphon 12" (305) 10" (254) The compression fitting should not extend more than 5 / (16) beyond the finished wall in order to be covered by the Vitrafvorm escutcheon. The compression fitting should not extend more than 5 / (16) beyond the finished wall in order to be covered by the Vitraform escutcheon. Rough-In for Straight stops and Angle Stops. Drawings above are guidelines for placement of exposed fittings in Vitraform installations. Stops should be level and centered on waste line. For deck mounted faucets, height and center to center of angle stops will be defined by the length of water lines of each individual faucet.

14 standard basin Installation Instructions 1.1.b Installation Instructions for Undermount Sink with or without Overflow Item No. 100, 150 & 170 Please provide these instructions to contractor at point of sale. CAUTION: This sink is made of glass. It is very strong, but sensitive to hard object impact, extreme change in temperature and high mechanical stress. Most damage to this product occurs during installation. Please follow installation instructions carefully. VITRAFORM sinks are intended and Warranteed for Lavatory use only. Sink Installation These instructions are for UNDER MOUNTED basins only. Refer to separate instructions for Drop-in basins on page install 1.1.c. Do not attempt to install this basin as self rimming unless it is White, Cobalt or Black glass. IMPORTANT NOTE: The use of Clear Silicone Adhesive is recommended for attaching this sink to most counter materials. It is virtually impossible to remove, ESPECIALLY ON FROSTED GLASS FINISHES, even before it sets. Extreme care must be taken while handling Silicone Adhesive in conjunction with this product. It is easier to attach an under-mount basin to an inverted counter before the counter is installed. The following instructions assume the appropriate cut-out has been made in the counter. 1. Choose the appropriate Vitraform cut-out template for Round, Oval or Rectangular basin. Place sink face down on the paper template aligning it to the line marked OUTER SINK EDGE. Using a felt tip pen, mark the cross hairs only on the ground edge of the sink. 2. Measure the cut-out and mark cross hairs on the counter to locate center of cut-out. Place the sink face down on the counter aligning corresponding cross hairs to lines drawn on counter. Trace line of outer sink edge on counter. 3. Set sink aside on clean, soft surface. Check to make sure the traced line of the edge of the sink is concentric to the cut-out. Lay down 1/8 bead of silicone just inside the traced line of the perimeter of the sink so that no silicone will be visible from the top of the counter. 4. Carefully set sink on counter aligning it to the traced line of the outer sink edge. If overflow is included, position overflow to either front or back as desired and align with cross hair marked on counter in step #2. Check once more to make sure the sink is aligned with the cutout in the counter. Using a finger, wipe any excess silicone to produce a small, clean joint at the sink edge. DO NOT GET SILICONE ON THE BOTTOM SURFACE OF THE GLASS. Any excess silicone may be removed after the silicone has set. 5. Secure sink in place on the counter with masking tape across the drain in a crisscross pattern to avoid shifting while the siliclone sets. Tape may be removed in 24 hours. 6. If the counter is already installed and sink must be installed from below, use above method in conjunction with supplied metal clips or similar device to hold sink in place while silicone sets. Allow silicone to set for 24 hours before removing clips. Choice of Installation with or without Overflow Overflow: hardware supplied A. Rubber Sink Grommet E. Rubber Washers B. Overflow Nipple F. Lower Collar C. Hex Tool G. O-ring D. Upper Tube Overflow Installation 1. insert lip of Rubber Sink Grommet A into drain hole of sink. 2. insert Overflow Nipple B and Rubber Washers E into overflow hole of sink and partially start threads into Upper Tube D while aligning Lower Collar F with Rubber Sink Grommet A. 3. Using Hex Tool C lightly tighten Overflow Nipple B. Drain Collar: hardware supplied H. Rubber Sink Grommet I. Overflow Collar Overflow Collar Installation 1. insert lip of Rubber Sink Grommet H into drain hole of sink. 2. Mate Overflow Collar I with Rubber Sink Grommet H. Drain Installation See Hardware pgs B.a-e for instructions on installing Vitraform drain systems with this basin. NOTE: Instructions for Round, Oval and Rectangular basins. Illustration showing round basin. D. Upper Tube B. Overflow Nipple E. Rubber Washers G. O-ring C. Hex Tool A. Rubber Sink Grommet F. Lower Collar Drain Collar Option H. Rubber Sink Grommet I. Overflow Collar Care for the Vitraform Glass Sink: Use commercial glass cleaners sprayed onto a soft cloth to clean glass surface(s). Wipe basin dry after use to avoid mineral deposits on glass left by water spots. For frosted glass, special attention to stubborn stains or adhesives may be required. Silicone or other adhesives may be impossible to remove from frosted finishes. If contamination occurs attempt to remove adhesive with glass cleaner first, then denatured alcohol, paint thinner or mineral spirits. If none of these solvents work, the stain might be removed by re-blasting the bowl. Contact the factory for authorization to return the product for evaluation. A return authorization must accompany the product. Please pack the sink in the original box or other proper packing to assure its safe return and insure for full value. Care for metal fittings and plated finishes: Wipe metal fittings dry after use to avoid water spots. Glass cleaner used on the Vitraform Glass Sink may be damaging to metal finishes. Use a diluted, neutral, liquid soap and a soft cloth to clean metal fittings. Never use an abrasive cloth or scouring pad.

15 standard basin Installation Instructions 1.1.c Installation Instructions for Drop-in Sink without Overflow Item No. 101, 151, 171 Please provide these instructions to contractor at point of sale. CAUTION: This sink is made of glass. It is very strong, but sensitive to hard object impact, extreme change in temperature and high mechanical stress. Most damage to this product occurs during installation. Please follow installation instructions carefully. VITRAFORM sinks are intended and Warranteed for Lavatory use only. Sink Installation This sink is intended to be installed as Self Rimming. The lip of the sink supports the bowl and seals to the surface to which it is fastened. A self adhesive clear rubber gasket is attached to a groove under the flange only on round and oval basins, this gasket is a temporary method of attachment to the mounting surface, allowing for minor irregularities between the counter and the lip of the sink. It provides a dam which will prevent silicone adhesive from getting under the lip of the sink where it will be unsightly. Surfaces and cut-outs below the basin will be visible even on Frosted sinks. Care should be taken to properly finish any material within 2 of a frosted basin. Black and Cobalt basins in all finishes and any color glass with White Lamination, Satin Etched or Mirror finish are dense enough to be installed as self-rimming without a gasket and may be attached to the counter with silicone adhesive alone (Item 171 is only offerred in these Color and Finish choices as no gasket is provided). IMPORTANT NOTE: The use of Clear Silicone Adhesive is recommended for caulking the outside edge of this sink to most counter materials. It is virtually impossible to remove, ESPECIALLY ON FROSTED GLASS FINISHES, even before it sets. Extreme care must be taken while handling Silicone Adhesive in conjunction with this product. 1. Prepare cut-out in mounting surface to allow the sink to overlap the cut-out 1 / 2 to 3 / 4 depending upon personal preference or use Vitraform cut-out template for Drop-in installation as a guide. 2. Mark a vertical and horizontal center line on masking tape placed just outside the line of the sink edge to align the template (or sink) to the cut-out, and trace outer sink line. Intructions for Round, Oval and Rectangular basins. Illustration showing round basin. 3. Clean the bottom surface of the sink lip including the groove for the Gasket. Remove a short section of paper from one side of the gasket only, and fit it into the sink groove, removing paper as the gasket is pressed in place. Carefully cut the gasket to length as the ends meet. 4. Perform a Dry Run installation by leaving the protective paper on the bottom of the Gasket and placing the sink onto the counter. Check position of the sink for its best fit and verify marks on the masking tape. Remove the sink. 5. Remove the protective paper from the Gasket. Make sure the gasket and mounting surface is clean and free of oil, wax or tape. Carefully place the sink into its appropriate position using the masking tape as a guide. Remove tape and clean counter. CAUTION: ONCE THE LIP OF THE SINK CONTACTS THE MOUNTING SURFACE IT IS VERY DIFFICULT TO SEPARATE THEM WITHOUT DAMAGING THE SINK OR THE CLEAR GASKET. Finish installation by carefully running a 1 / 16 bead of clear silicone around the polished edge of the sink just where it contacts the mounting surface. Smooth the silicone with a finger to produce a neat, small joint, providing a secure and water tight bond. Drain Collar Hardware Supplied A. Rubber Sink Grommet B. Overflow Collar C. Clear Rubber Gasket with self adhesive Standard Basins WITH Overflow may not be installed as Self-rimming without notching the counter for the overflow hardware. Contact factory for assistance. Overflow Collar Installation 1. insert lip of Rubber Sink Grommet A into drain hole of sink. 2. Mate Overflow Collar B with Rubber Sink Grommet A. Drain Installation See Hardware pgs B.a-e for instructions on installing Vitraform drain systems with this basin. C. Clear Rubber Gasket A. Rubber Sink Grommet B. Drain Collar Care for the Vitraform Glass Sink: Use commercial glass cleaners sprayed onto a soft cloth to clean glass surface(s). Wipe basin dry after use to avoid mineral deposits on glass left by water spots. For frosted glass, special attention to stubborn stains or adhesives may be required. Silicone or other adhesives may be impossible to remove from frosted finishes. If contamination occurs attempt to remove adhesive with glass cleaner first, then denatured alcohol, paint thinner or mineral spirits. If none of these solvents work, the stain might be removed by re-blasting the bowl. Contact the factory for authorization to return the product for evaluation. A return authorization must accompany the product. Please pack the sink in the original box or other proper packing to assure its safe return and insure for full value. Care for metal fittings and plated finishes: Wipe metal fittings dry after use to avoid water spots. Glass cleaner used on the Vitraform Glass Sink may be damaging to metal finishes. Use a diluted, neutral, liquid soap and a soft cloth to clean metal fittings. Never use an abrasive cloth or scouring pad.

16 standard basin Installation Instructions 1.1.d ADA Guidelines for Undermount Installation with Basin Item No. 100 & 150 Please provide these instructions to contractor at point of sale. Round Undermount 100 with Wall Faucet 1 Reach Oval Undermount 150 with Wall Faucet 1 Reach Dimension Reference Chart Item Description Dim. A Counter Height 34. B Apron 29 Min. C Knee Clearance 27 Min. D Toe Clearance 9 Min. E Rough-in 22 F Knee Clearance 8 Min. G Toe Clearance 6. 22" 22" DECK FAUCETS: Reach to faucet handle must be imum 19. Faucet may be positioned to side or on angle to accommodate basin. Provide faucet specification and request drawing from factory for coordination. NOTE: The information above is for general reference only. Please refer to published ADA Guideline for local compliance and exact requirements. (see Figs. 31 & 32). Round Undermount 100 with Deck Faucet Oval Undermount 150 with Deck Faucet 1 Reach 1 Reach 22" 22"

17 standard basin Installation Instructions 1.1.e ADA Guidelines for Drop-in Installation with Basin Item No. 101 & 151 Please provide these instructions to contractor at point of sale. Round Drop-in 101 with Wall Faucet 1 Reach Oval Drop-in 151 with Wall Faucet 1 Reach Dimension Reference Chart Item Description Dim. A Counter Height 34. B Apron 29 Min. C Knee Clearance 27 Min. D Toe Clearance 9 Min. E Rough-in 22 F Knee Clearance 8 Min. G Toe Clearance 6. 22" 22" DECK FAUCETS: Reach to faucet handle must be imum 19. Faucet may be positioned to side or on angle to accommodate basin. Provide faucet specification and request drawing from factory for coordination. NOTE: The information above is for general reference only. Please refer to published ADA Guideline for local compliance and exact requirements. (see Figs. 31 & 32). Round Drop-in 101 with Deck Faucet Oval Drop-in 151 with Deck Faucet 1 Reach 1 Reach 22" 22"

18 standard basin Installation Instructions 1.1.f ADA Installation Guidelines for Undermount or Drop-in Basin Item No. 170 & 171 Please provide these instructions to contractor at point of sale. Rectangular Undermount 170 with Wall Faucet 1 Reach Rectangular Drop-in 171 with Wall Faucet 1 Reach Dimension Reference Chart Item Description Dim. A Counter Height 34. B Apron 29 Min. C Knee Clearance 27 Min. D Toe Clearance 9 Min. E Rough-in 22 F Knee Clearance 8 Min. G Toe Clearance 6. M 24" 24" DECK FAUCETS: Reach to faucet handle must be imum 19. Faucet may be positioned to side or on angle to accommodate basin. Provide faucet specification and request drawing from factory for coordination. NOTE: The information above is for general reference only. Please refer to published ADA Guideline for local compliance and exact requirements. (see Figs. 31 & 32). Rectangular Undermount 170 with Deck Faucet Rectangular Drop-in 171 with Deck Faucet M 1 Reach 1 Reach 24" 24"

19 standard basin Worksheet 1.1.w Worksheet for Items: 100, 101, 150, 151, 170 & 171 This Worksheet is provided for your convenience. Please refer to the current Vitraform General Price List to build a complete item number and price for this product. P.O. No: Date: Sales Person: Tel: Ext: Quantity: Please use additional Order Forms for non-identical orders. Glass Order Order No: A B C D E Price: $ NA NA TOTAL $ Overflow Overflow See Hardware pg B.1.8 Basins with Overflow require this fitting. Round Oval Rect. o Overflow 911.XX 916.XX 918.XX No Overflow without Overflow See Hardware pg B.1.7 Basins without Overflow require this fitting to install drain. Round Oval Rect. o Collar 900.XX 900.XX 900.XX Drains (optional) for Overflow See Metal Finish Key below for XX v Drains (optional) for No Overflow See Metal Finish Key below for XX Drains Drain Set with: US Trap Euro Siphon o Grid Strainer 810.XX 810.XXS o Pivot Drain 820.XX 820.XXS o Dome Open 860.XX 860.XXS o Dome Pop-up 862.XX 862.XXS Drains Drain Set with: US Trap Euro Siphon o Grid Strainer 811.XX 811.XXS o Pivot Drain 821.XX 821.XXS o Dome Open 861.XX 861.XXS o Dome Pop-up 863.XX 863.XXS Finish Key Call for quote on custom finishes. Example: Fin. Group 1 Code Fin. Group 2 Code Fin. Group 3 Code Fin. Group 4 Code Add 2 digit Finish Code to 3 digit Item No. Polished Chrome 10 Polished Nickel 12 Oil Rubbed Bronze 15 Polished Gold = Grid with US PTrap Satin Chrome Satin Chrome 20 PVD Brass 16 Satin Gold 23 Satin Nickel 22 Satin Brass 21