SOUP MAKER HR2202/80 SHW R1. Technical information. Difference in Power Cord:

Size: px

Start display at page:

Download "SOUP MAKER HR2202/80 SHW R1. Technical information. Difference in Power Cord:"

Lorin Barnett
5 years ago
Views:

SOUP MAKER HR2202/80 Technical information -Voltage -

220V-240V : 50Hz : 120W : 900-990W -Product dimensions( LxDxH)

- Motor housing :1000~1200ml (for2~4 people) : 2.

Difference in Power Cord: HR2202/80 Published by Philips

1 SOUP MAKER HR2202/80 Technical information -Voltage - Frequency rated -Motor Power rated -Heating Power rated : 220V-240V : 50Hz : 120W : W -Product dimensions( LxDxH) mm 205x153x310mm -Capacity -Net Weight Material - Jug - Blade - Motor housing :1000~1200ml (for2~4 people) : 2.0kg : Stainless steel :stainless steel : PP (foodcontact) Difference in Power Cord: HR2202/80 Published by Philips Consumer Lifestyle Printed in China Copy Right Reserved Subject to modification 1 SHW R1

2 Product introduction Control panel A: Smooth soup program with light. Smooth soup program to make a smooth soup in 23 minutes. B: Chunky soup program with light. Chunky soup program to make a chunky soup in 20 minutes. C: Compote program with light. Compote program to make a compote in 13 minutes. D: Smoothie program with light. Smoothie program to make a smoothie in 3 minutes. E: Manual blending program with light F: Power on/offbutton G: Display screen H: Program selection button I: Program start button 2

3 Main feathers 1 2 DC motor,light weight and small noise 3 Unique blade design, perfect blading performance. Cageless design, easier clean 3

4 Technical information - Circuit diagrams: 4

5 Technical information - Function Flow Chart _ Cream Soup Event: Power on Action: Standby mode Event: Program Cream Soup selected, Start/Stop pressed Action: Cream Soup LED steady on Timer countdown 23min Action: Beep Duration: 1s Action: Heat Power: 100% Duration: 10 min Foam detection on Foam Alarm > 3ms Pause: 10s Action: motor on Power: 100% Duration: 10s Action: Heat on2s off 9s Routine: if foam alarm> 3ms: stop heating for 15s Duration: stop heating 20min after program has been started Pause: 10s Action: motor on Power: 100% Routine: 30s on, 10s off between Cycles: 4x Action: Beep Duration: 1s on, 0,8s off Repeat: 6x Action: Cream Soup LED flashing (0,5s on / 0,5s off). 5

6 Technical information - Function Flow Chart _Chunky Soup Event: Power on Action: Standby mode Event: Program Chunky Soup selected, Start/Stop pressed Action: Chunky Soup LED steady on, Timer countdown 20min Action: Beep Duration: 1s Action: Heat Power: 100% Duration: 10 min Foam detection on Foam alarm > 3ms Pause: 10s Action: Heat on2s off 9s Routine: if foam alarm> 3ms: stop heating for 15s Duration: stop heating 20min after program has been started Action: Beep Duration: 1s on, 0,8s off Repeat: 6x Action: Chunky Soup LED flashing (0,5s on / 0,5s off). 6

7 Technical information - Function Flow Chart _Compote Event: Power on Action: Standby mode Event: Program Compote selected, Start/Stop pressed Action: Compote LED steady on Timer countdown 13min Action: Beep Duration: 1s Action: Heat on2s off 9s Routine: if foam alarm >3ms: stop heating for 15s Duration: 13 min Action: Beep Duration: 1s on, 0,8s off Repeat: 6x Action: Compote LED flashing (0,5s on / 0,5s off). 7

8 Technical information - Function Flow Chart _Smoothie Event: Power on Action: Standby mode Event: Program Smoothie selected, Start/Stop pressed Action: Smoothie LED steady on Timer countdown 4min Action: Beep Duration: 1s Action: motor on Power: 100% Routine: 30s on, 10s off Cycles: 5x Action: Beep Duration: 1s on, 0,8s off Repeat: 6x Action: Smoothie LED flashing (0,5s on / 0,5s off). 8

9 Technical information - Function Flow Chart _Manual Blending Event: Power on Action: Standby mode Event: Program Manual Blending selected Action: Smoothie LED steady on Event: if Start/Stop button pressed-> Action: motor on Power: 100% Blending LED flashing (0,5s on / 0,5s off) Timer countdown 30s Duration: as long as Start/Button button is pressed or reach 30s If Start/Stop button is released -> Action: motor off Blending LED lights continuously flashing, Timer reset If Select button is pressed return to Standby mode 9

10 Technical information - Function Flow Chart _Auto Keep Warm Event: Enter auto keep warm mode Action: Selected recipe LED flashing (0,5s on / 0,5s off) Timer countdown 60min Action: Heat on1s off 120s Routine: if foam alarm >3ms: stop heating for 15s Duration: 60 min Action: Beep Duration: 5s Action: Selected recipe LED flashing (0,5s on / 0,5s off). 1 0

11 Exploded drawing

12 Exploded drawing

13 Exploded drawing

14 Spare parts Position 12NC Part name PCM Remark Vent Valve Handle of control Handle Control cover PCB board Surface cover decoration piece Surface cover decoration piece of silica gel Coupler silica gel The upper coupler UI film DC motor Shaft silicon rubber sealing ring (inside) Vent valve seal silica gel Plastic body silicon rubber sealing ring Machine body Overflow sensor Metal fuselage silicon rubber sealing ring Shaft hole "U" type oil seal Oil seal fixed plate Shaft silicon rubber sealing ring (outer) Stainless steel cage Silica gel sesal ring Blade Stainless steel pot Thermostat Lower coupler ASSY Coupler bolt Handle cover Handle base Stainless steel shell Socket Base Power cord Measuring cup

How to replace PCB. Step 1:Remove all the screws.

15 DISASSEMBLY ADVISE! Before you start dismantling! For your safety be sure the plug is disconnected from the mains! How to replace PCB. Step 1:Remove all the screws. Step 2: Remove 5 screws. Step 4:You can get PCBA Step 3: Detach the cables and remove the screw. 15

16 DISASSEMBLY ADVISE! Before you start dismantling! For your safety be sure the plug is disconnected from the mains! How to replace DC Motor Step 1:Remove all the screws. Step 2: Remove 5 screws. Step 3: Detach the cables and remove the screw. 16

17 Step 4: Remove the nut, blade and stainless steel cover. Step 5: Remove the screws. DC motor 17

18 Trouble shooting Overflow Proper program selected? Select proper program according to recipe Change ingredients and restart Water level? Too much or too less water Fill in water between MINwith MAX Ingredients? Too much ingredients According to recipe tocontrol the quantity Is Overflow normal? Overflow isdirty Clean the overflow Overflow cable isbroken Repair it Overflow cable isn t connected with grounding wire connect Is main PCBA normal? Replace mainpcba Air leaked frommotor house Replace motor house Issue close 18

19 Trouble shooting Plug in the appliance, no power. NEW Is coupler connection ok? Upper coupler and lower coupler disconnect Change Lower coupler ASSY Is jugok? Thermostat or Thermal fuse fault Replace socket assy Is PCB assy ok? PCB assy fault Replace PCB assy Appliance power on, but no blend. NEW Is motor shaft jammed? Motor failed byrust jammed motor shaft Replace motor assy & PCB assy Is motor fault? Motor fault Replace motor assy Is PCB assy ok? PCB assy fault Replace PCB assy 19

20 Trouble shooting Power on but no heating function. NEW Heating element is OK? Heating element failure Change Stainless steel pot PCBA board failure Replace PCBA board After 20 minutes, ingredients are notbladed. LED lights flash Select program Press Start Was water be heated? power, replace mainpcba Check or replace DC motor if necessary Alarming when power cord plugs in Does water level touch overflow sensor? Ensure water level betweenmin and MAX Overflow sensorshort cut Clean overflow sensor Replace main PCBA 20

21 Trouble shooting Problem Cause Solution The appliance doesn t work The light of selected mode doesn t go on The light of selected program is on, but the appliance doesn t work The ingredients have not blended well The appliance overflows There is connection problem The motor unit does not fit onto the jug properly because there are too many ingredients in the jug. Check if the small plug is inserted in the appliance properly and if mains plug is inserted in the wall socket properly. Remove the plugs and reinsertthem. Remove some of the ingredients and make sure not to fill the jug beyond the MAX indication. Please contact with local service center or Motor unit problem call center Check if the small plug is inserted in the appliance properly and if mains plug is inserted in the wall socket properly. Remove There is connection problem the plugs and reinsertthem. During making process, Please follow the proper steps to make power had been cut off. soup. Make sure motor unit connector and thejug The motor unit does notfit connector are aligned before you lower the onto the jug properly motor unit into the jug. Remove some of the ingredients and make sure the ingredients are spread evenly over the bottom of thejug. You have exceeded the MAX indication in the jug. You have not pressed start button. Press the startbutton. Remove some of the ingredients and make You have exceeded the sure the ingredients are spread evenly over MAX indication in the jug. the bottom of thejug. Remove some of the ingredients and make You have exceeded themax sure the ingredients are spread evenly over indication in the jug the bottom of thejug. You have selected wrong program Select correct program according torecipe You have exceeded themax indication in the jug The overflow sensor is dirty You have selected wrong program You did not add enough water or other liquid Remove some of the ingredients and make sure the ingredients are spread evenly over the bottom of thejug. The overflow sensor prevents theappliance from overflowing. Clean the overflowsensor. Select correct program according torecipe Make sure the liquid level is above the MIN and below the MAX indication. The soup maker is not suitable forheating up milk. The food is burnt You have heated up milk This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit for a list of frequently asked questions or contact the Consumer Care Centre in your country. 21

º CP0398/01 Padholder assy Switch 2-cup

º CP0398/01 Padholder assy Switch 2-cup Senseo Switch HD7892/60 HD7892/61 Philips Consumer Lifestyle Service Manual Product information This product meets the requirements regarding interference suppression on radio and TV. After the product