INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE INSTALLATION MANUAL. Dual Fuel 30-inch Wide Free-StandingRange

Transcription

1 INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE INSTALLATION MANUAL Dual Fuel 30-inch Wide Free-StandingRange PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE THE MANUAL IS INTENDED TO ASSIST IN THE INITIAL INSTALLATION AND ADJUSTMENTS OF THE RANGE. CLEARANCE DIMENSIONS Only qualified personnel should install or service this range. Read "Safety Instructions" in the Use & Care book before using range. Improper installation, adjustment, alteration, service, maintenance or use of range can result in serious injury or property damage, WARNING ALL RANGES CAN TIP AND CAUSE INJURIESTO PERSONS. INSTALL ANTI-TIP DEVICES PACKED WITH RANGE. FOLLOW ALL INSTALLATION INSTRUCTIONS. Your range may not be equipped with some of the features referred ; oin this manual, Range may be installed with zero inches clearance adjacent to (against) combustible construction at the rear and on the sides below the cooktop. For complete information in regard to the installation of wall cabinets above the range and clearances to combustible wall above the cooking top see the installation drawings. For SAFETY CONSIDERATIONS do not install a range in any combustible cabinetry which is not in accord with the installation drawings. * NOTE: The 30 inch (76.2 cm) dimension may be reduced to not less than 24 inches (61 cm) when the wall cabinets in a domestic home are protected with fireproof materials in accordance with American National Standards - National Fuel Gas Code or in mobile homes when they are protected with fireproof materials in accordance with the Federal Standard for Mobile Home Construction and Safety. To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 inches (13 cm) beyond the bottom of the cabinets. CAUTION: This range has been designed in accordance with the requirements of various safety agencies and complies with the maximum allowable wood cabinet temperatures of 194 F. If this range is installed with cabinets that have a lower working temperature than 194 F, discoloration, delamination or melting may occur. Contact Customer Service for associated cabinet dimensions and installation accessories P ( )

2 INSTALLATION DRAWINGS Note: Diagramis for newinstallation.preexistingstructures mayneedmodificationfor properinstallation. GASANDELECTRICALSUPPLYSHOULDNOTCONVERGE. DONOTGROUNDELECTRICALSUPPLYTOGASSUPPLYUNES, NOTE: TO ENSUREFLUSH TO WALL INSTALLATIONGAS SERVICE INCLUDING SHUT-OFFVALVESHOULDNOTPROTRUDEMORETHAN3"(7,6CM)FROMREARWALL PROVIDE FOB VOLT VOLT FLUSH OUTLET PER APPLICABLE IN THIS AREA CORD "A" : 30" (76.2 CM) - 31" (78,7 CM) FOR CANADA "B" : 3 I/4" (8.3 CM) " (9.5 CM) FOR CANADA GAS LiNE LOCATION 25" (63.5 CM) COURTER NORMAL,_--T L_(_PS DEPTH m "-_14.6"CM) F, -- 24" (6ICM) i CABINET DEPTH 36" (9t.5 CM} COUNTER TOP HEIGHT 8" t4" CM). A Jl PROVIDE FOR 12O1208 VOLT, OPE 120/24u VOLT UPPER & LOWER OUTLET BOX PER APPLICABLE CORD IN THIS AREA THIS PRODUCT SHOULD NOT BE INSTALLED BELOW A VENTILATION TYPE HOOD SYSTEM THAT DIRECTS AIR IN A DOWNWARD DIRECTION. (SEE FIGURE) THESE SYSTEMS MAY CAUSE IGNITION AND COMBUSTION PROBLEMS WITH THE GAS BURNERS RESULTING IN PERSONAL INJURY AND MAY AFFECT THE COOKING PERFORMANCE OF THE UNIT. _,;/////////////////4, NOTE: THE FIGURE MAY NOT ACCURATELY REPRESENT YOUR RANGE OR COOKTOP; HOWEVER, THIS WARNING APPLIES TO ALL GAS COOKING PRODUCTS. Y/////////////////// ART _

3 (SEE NOTE ON front PAGE) ANY COMBUSTIBLE SURFACE 30" {76,? CM) +3" (33 CM) WAXIMU_ DEPTH OF CABINETS ABOVE COOK TOP O" {0 CW) CLEARANCE BETWEEN ADJACENT COMBUSTIBLE SURFACES AND THE BACK AND SIDES OF THE RANGE, BELOW THE COOKING SURFACE 3G" (91.5 CM) COUNTER TOP HEIGHT _2 NOTE: COOKTOP MUST BE FLUSH OR ABOVE COUNTERTOP DIMENSION "A" SIDE CLEARANCE ABOVE COOKING SURFACE = 3 INCHES (7.6 CM) (MINIMUM) Check the range model number plate located on lower front of range to see if the range is approved for installation in mobile homes and!or recreational park trailers. If approved the following items are applicable. MOBILE HOMES The installation of a range designed for mobile home installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24 HUD, (Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A, or with local codes. In Canada the range must be installed in accordance with the current CSA Standard C Canadian Electrical Code Part 1 and Section Z Installation Requirements for Gas Burning Appliances in Mobile Homes (CSA Standard CAN!CSA - Z240MH). RECREATIONAL PARK TRAILERS The installation of a range designed for recreational park trailers must conform with state or other codes or, in the absence of such codes, with the Standard for Recreational Park Trailers, ANSI A119.5-latest edition. In Canada the range must be installed in accordance with CANiCSA - Z Electrical Requirements for R.V.'s (CSA Standard CAN/CSA - Z240 RV Series) and Section Z Installation Requirements for Propane Appliances and Equipment in R.V.'s (CSA Standard CAN/CSA - Z240 RV Series). LOCATING THE RANGE Place range in a well lit area. Do not set range over holes in the floor or other locations where it may be subject to strong drafts. Any opening in the wall behind the range and in the floor under the range should be sealed. Make sure the flow of cooling! ventilation air is not obstructed below the range. NOTE: A range should NOT be installed over kitchen carpeting. -3-

4 ANTI-TIP DEVICE INSTALLATION INSTRUCTIONS NOTE: A risk of range tip over exists if the appliance is not installed in accordance with the installation instructions provided. The proper use of this device minimizes the risk of TIP-OVER. In using this device the consumer must still observe the safety precautions as stated in the USE and CARE MANUAL and avoid using the oven door and/or lower drawer as a step stool. Installation instructions are provided for wood and cement in either floor or wall. Any other type of construction may require special installation techniques as deemed necessary to provide adequate fastening of the ANTI-TIP bracket to the floor or wall. STEP 1 - Locating The Bracket (see figure 1) A. Determine where either the right or left rear "edge" of the range will be located and mark the floor or wall. B. Place the BRACKET 9/16" (14.5 mm) from the marked "EDGE" toward center of opening and against the back wall as shown in figure 1, with orientation hole against wall. C. Use the bracket as a template and mark the required holes, as shown in figure 1 for the type of construction you will be using. STEP 2 - Anti-Tip Bracket Installation A. Wood Construction: 1. Floor: Locate the center of the two holes identified in figure 1 as "HOLES FOR FLOOR". Drill a 1/8" (3 mm) pilot hole in the center of each hole (a nail or awl may be used if a drill is not available). Secure the ANTI-TIP bracket to the floor with the two screws provided. Proceed to STEP Wall: Locate the center of the two holes identified in figure 1 as "HOLES FOR WALL. Drill an angled 1/8" (3 mm) pilot hole in the center of each hole as shown in figure 2. (A nail or awl may be used if a drill is not available). Secure the ANTI-TIP bracket to the wall with the two screws provided as shown in figure 2. Proceed to STEP 3. B, Cement or Concrete Construction: 1. Suitable screws for concrete construction can be obtained at a hardware store. Drill the required size hole for the screws obtained into the concrete at the center of the holes identified in figure 1 as "HOLES FOR FLOOR". Secure the ANTI-TIP bracket to the floor. Proceed to STEP 3. STEP 3 - Range Installation A. For safety considerations as well as optimum performance, adjust the range so it is level and to desired height prior to installing in cabinet opening. NOTE: Cooktop countertop, MUST be flush or above Levelness may be checked by placing a spirit level or a large pan of water on the cooktop or oven rack. Adjust the range by tipping it forward or back and rotate the leveling feet as required. NOTE: A minimum clearance of 1/4" (6 mm) is required between the range and the leveling foot that will engage the anti-tip bracket, (see figure 2). CAUTION: Damage to the range may occur if range is moved or lifted by grasping the main top, backguard or door handles. B, Align the range to its designated location and prepare to slide it back into position. Connect gas line and plug in power cord to outlet following guidelines outlined in connecting the range and remainder of installation instructions. C, D, Slide range in place visually inspecting to verify that power cord and gas line are freely routed and contained within recessed area of back panel. To check the range for proper installation of the anti-tip bracket, use a flashlight and look underneath the bottom of the range to see that one of the rear leveling feet is engaged in the bracket slot. NOTE: USE A MINIMUM OF (2) SCREWS TO install ANTI-TIP BRACKET TO THE WALL OR FLOOR I W/_LL TO THEWALL OR FLOOR. [ _ -_ "_ ANT -T P I _ BRACKET ANTI-TIP SCREWS MUST BRACKET ENTER WOOD OR METAL SCREW BRACKET SLIDE IN WALL PLATE TO SECURE RANGE BOTTOM 7 FLOOR _4_ 9_/_,4io" AR1_ t FIGURE 1 FIGURE 2-4-

5 CONNECTING THE RANGE ELECTRIC SUPPLY The range must be installed in accordance with Local and National Electric Code (NEC) ANSl/NFPA No. 70-latest edition. See rating plate for total connected KW rating. ELECTRIC SUPPLY (Canada) The range must be installed in accordance with Local and Canadian Electric Code CSA STD.C22.1 latest edition. See rating plate for total connected OUTSIDE WIRING KW rating. Your local utility company will tell you whether the present electric service to your home is adequate. It may be necessary to increase the size of the wiring to the house and service switch to take care of the electrical load demanded by the range. The kilowatt rating for the range is specified on the rating plate located on front of range. HOUSE WIRING Most local Building Regulations and Codes require that all electrical wiring be done by licensed electricians. All wiring should conform to Local and National Electrical Codes. This range requires a single phase three wire 120/240 or a 120/208 volt, 60 Hz, AC circuit. Wiring codes require a separate circuit be run from the main entrance panel to the range and that it be equipped with separate disconnect switch and fuses, either in the main entrance panel or in a separate switch and fuse box. In some communities, a solid or flexible continuous armored conduit must be used from main entrance panel to the terminal box on the rear of the range. Others will permit the termination of the range circuit at a polarized three or four wire plug-in outlet placed at a convenient point near the back of the range. The range is then connected to this outlet through an approved range connector (pigtail) fastened securely to the terminal block with proper strain relief at the range and a three or four pronged plug at the opposite end. RANGE CONNECTIONS Some models are shipped direct from the factory with service cords (pigtails) attached. There are no range connections necessary on these models. Just plug into the range outlet. On models not provided with a service cord, connection to the power supply is necessary. REMEMBER - only a 4-conductor cord is to be used on new branch-circuit installations (1996 NEC), mobile homes, recreational vehicles, or in an area where local codes prohibit grounding through the neutral conductor. Hence, 4-wire service MUST be provided for such installations. 3-wire service may be used when permitted by local code. USE COPPER OR ALUMINUM CONDUCTORS. Main terminal block is recognized for Copper or Aluminum conductors. If a flexible power cord is required, it is recommended a cord no longer than 4 ft. be used. Make connections as explained below and with reference to the appropriate illustration (see figures 6 and 7). After installation, insure tightness of all electrical connections and replace all covers. Remove terminal (See figure 5). block access cover from range back. RANGE CONNECTIONS (Canada) This model was shipped direct from the factory with service cord (pigtail) attached. There are no range connections necessary. Just plug into the range outlet. NOTE: Cord replacement - ONLY a power supply cord rated at 240 volts minimum, 40 amperes or 50 amperes power supply cord that is marked for use with nominal 1 3/8" (34.93 mm) diameter connection opening, with closed loop terminals and marked for use with ranges shall be used. / \ ACC[S$ _ COVER FIGURE 3 o MAIN TERMINAL CONNECTION BLOCK -5-

6 CONNECTING THE RANGE FIGURE 4 3-Wire Service Cord or Conduit Installation 1. Insure that the copper ground strap IS CONNECTED between the middle post of the main terminal connection block and the range chassis. 2. If bare copper or aluminum wiring is used, attach adapter lugs as shown in figure 4. (See Bare Wire Connection), Torque specifications are shown below. 3, The middle wire of the service cord or ground lead of 3-wire conduit MUST connect to the neutral (middle) post of the main terminal block. The other two wires of the service cord or conduit connect to the outside posts of the main terminal connection block. Polarity is unimportant. If using bare wire, attach wire to appropriate lug as shown. Torque specifications are shown below. 4. An appropriate strain relief for service cord or conduit MUST be attached to the conduit plate. ACCEPTABLE - 3 WIRE PLUG INSTALLATION WHITE RED MAIN TERMINAL CONNECTIONBLOCK BLACK RED CONDUIT PLATE NtDDLE WIRE OF SERVICE CORD OR CONDUIT STRAIN RELIEF GROUNDINGSTRAP CONNECTEDAT FACTORY ADAPTER LUGSLOCATED IN LITERATUREKIT BLACK BARE WIRE TOROU_ SP[CIFICATION WHITE LUGATTACHEDTO TERHINALDLOCK- 20 IN.L IN-L6 O 25 IN-LB 4.5 3S Ii-Lfi FLOOR ' FOR USE WITH CONDUIT. REMOVEBRACKET.FLIP & RE-ATTACHWITH SHALL HOLEVISIBLE, ALTERNATIVE" INSTALLATION RECEPTACLE MOUNTEDFLUSH TO WALL OUTLET RECEPTACLE TO BE ROTATE IN ACCORDANCE WITH LOCAL CODES FIGURE 4-6-

7 CONNECTING THE RANGE FIGURE 5 4-Wire Service Cord or Conduit Installation (Mobile Homes Or As Required By Codes) 1. The copper ground strap connected between the neutral (middle) post of the main terminal block and the chassis MUST be cut off as shown in figure 5. Save the green ground screw to attach the ground from the 4 wire cord. Only a 4 wire cord or conduit should be used. 2. If bare copper or aluminum wiring is used, attach adapter lugs as shown in figure 5. (See Bare Wire Connection). Torque specifications are shown below, 3, The ground wire from the service cord or conduit must connect to the range chassis using the green ground screw. 4. The white wire of the service cord or conduit must connect to the neutral (middle) post of the main terminal block. The other two wires of the service cord connect to the red and black posts of the main terminal block, respectively. If using bare wire, attach wire to appropriate lug as shown. Torque specifications are shown below. 5. An appropriate strain relief for service cord or conduit MUST be attached to the conduit plate. Conversion From 3-Wire To 4-Wire Service (Free-standing Model With 3-Wire Service Cord Attached). Disconnect range from power. Remove the access cover on back of range and remove the 3-wire service cord from the main terminal block. Follow instructions as outlined in figure 5 to connect the 4-wire service cord, NOTE: Cord replacement - ONLY a power supply cord rated at 240 volts minimum, 40 amperes or 50 amperes power supply cord that is marked for use with nominal 1 3/8" (34.93 mm) diameter connection opening, with closed loop terminals and marked for use with ranges shall be used. ACCEPTABLE - 4 WIRE PLUG INSTALLATION BLACK RED CHASSIS GROUND STRAIN RELIEF MIDDLE WIRE OF / SERVICE CORD OR CONDUIT ADAPTER--_"'_..._ -'"--WHITE LUGS LOCATED _'_' IN LITERATURE KIT _"_-'BLACN BARE WIRE TOROg[ SPECIFICATIONS LUGATTACHED TOTEWWALRLOCK- ZOJN-LO I-I12 13,8 CM) MINIMUM } FLOOR _USE WITH CONDUIT, IO-14 ZO IN'LB 8 Z$ IN'LN 4-$ 35 IN-LB ALTERNATIVF INSTA!IATION REMOVE BRACKET, FLIP RE-ATTACH Tire SMALL HOLE VISIBLE, Z OUTLET RECEPTACLE MOUNTEDFLUSH TO WALL OUTLET RECEPTACLE TO BE ROTATED IN ACCORDANCE WITH LOCAL CODES FIGURE 5-7-

8 CONNECTING THE RANGE Gas Supply Installation of this range must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-latest edition. In The Commonwealth Of Massachusetts This product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of Massachusetts. A "T" handle type manual gas valve must be installed in the gas supply line to this appliance. A flexible gas connector, when used. must not exceed a length of three (3) feet / 36 inches. In Canada the range must be installed in accordance with the current CGA Standard CAN/CGA-B149 - Installation Codes for Gas Burning Appliances and Equipment and/or local codes. Gas leaks may occur in your system and result in a dangerous situation. Gas leaks may not be detected by smell alone. Gas suppliers recommend you purchase and install an UL approved gas detector. Install and use in accordance with the manufacturer's instructions. Checking Pressure Of House Piping System 1. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 Ibs./sq. in. (3.5 kpa) (13.8 in. water column). 2. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 Ibs./sq. in. (3.5 kpa) (13.8 in. water column). Gas Supply Connection (See figure 3) A QUALIFIED SERVICEMAN OR GAS APPLIANCE INSTALLER MUST MAKE THE GAS SUPPLY CONNECTION. Leak testing of the appliance shall be conducted by the installer according to the instructions given in section h. NATURAL GAS SUPPLY LINE MUST HAVE A NATURAL GAS SERVICE REGULATOR. INLET PRESSURE TO THIS APPLIANCE SHOULD BE REDUCED TO A MAXIMUM OF 14 INCHES WATER COLUMN (0.5 POUNDS PER SQUARE INCH (P.S.I.). LIQUEFIED PETROLEUM (LP.)/PROPANE GAS SUPPLY LINE MUST HAVE ALP. GAS PRESSURE REGULATOR. INLET PRESSURE TO THIS APPLIANCE SHOULD BE REDUCED TO A MAXIMUM OF 14 INCHES WATER COLUMN (0.5 ES.I.). INLET PRESSURES tn EXCESS OF 0.5 ES.I. CAN DAMAGE THE APPLIANCE PRESSURE REGULATOR AND OTHER GAS COMPONENTS IN THIS APPLIANCE AND CAN RESULT IN A GAS LEAK. NOTE: This range is shipped from the factory set for Natural Gas at 4" water column pressure. Gas supply pressure for testing regulator must be at least 1" water column pressure above manifold pressure shown on serial plate. If conversion to LP Gas is required, convert appliance before installation. -8-

9 OFF RecommendedGas Supply Connections a. REGULATOR SHUT-OFF VALVE ON A GAS CUTOFF VALVE SHOULD BE PUT IN AN ACCESSIBLE LOCATION IN THE SUPPLY LINE AHEAD OF THE RANGE, FOR TURNING ON AND TURNING OFF GAS SUPPLY. If range is to be connected to house piping with flexible or semi-rigid metal connectors for gas appliances, CONNECTOR NUTS MUST NOT BE CONNECTED DIRECTLY TO PIPE THREADS. THE CONNECTORS MUST BE INSTALLED WITH ADAPTORS PROVIDED WITH THE CONNECTOR. REGULATOR b. The house piping and/or range connector used to connect the range to the main gas supply must be clean, free of metal shavings, rust, dirt and liquids (oil or water). Dirt, etc. in the supply lines can work its way into the range manifold and in turn cause failure of the gas valves or controls and clog burners and/or pilot orifices. CAUTION: DO NOT LIFT OR MOVE RANGE BY DOOR HANDLES, OR BACKGUARD. I12" NPT MALE TO 318" NPT FEMALE ADAPTER BUSHING c. Turn off all pilots and main gas valve of other gas appliances. Q.FLEXIBLE SUPPLY LINE d. Turn off main gas valve at meter. e. Before connecting range, apply pipe thread compound approved for LPG to all threads. Use only a flexible connector to connect range to gas supply at appliance pressure regulator using adaptors supplied with connector. Regulator supplied with range has 1/2" NPT female connection. NOTE: It is recommended to use a CSA certified flexible connector no longer than 36" (91.4 cm) with a minimum BTU/HR rating of 88,200, and in accordance with local codes. See serial plate for type of gas range has been manufactured for. g. Turn on main gas valve at meter, and relight pilots at other gas appliances. FIGURE 6 WHEN THE INSTALLER HAS COMPLETED INSTALLATION OF THE APPLIANCE, LEAVE THE APPLIANCE PRESSURE REGULATOR SHUT-OFF VALVE IN THE "ON" POSITION. h, Apply a non-corrosive leak detection fluid to all joints and fittings in the gas connection between the supply line shut-off valve and the range. Include gas fittings and joints in the range if connections were disturbed during installation. Check for leaks! Bubbles appearing around fittings and connections will indicate a leak. If a leak appears, turn off supply line gas shut-off valve, tighten connections, turn on the supply line gas shut off valve, and retest for leaks. CAUTION: NEVER CHECK FOR LEAKS WITH A FLAME. WHEN LEAK CHECK IS COMPLETE, ALL RESIDUE. WIPE OFF -9-

10 RANGE ADJUSTMENTS Top Section - Electric Ignition To operate, push and turn top burner knob to the LITE position. The top burner will light. To turn OFF spark after the top burner has ignited, turn knob to Ht setting. GAS CONVERSION SEE INSTRUCTIONS FOR GAS CONVERSION LOCATED ON THE BACK OF THE RANGE. NOTE: Top burners are not adjustable. Air Shutter - Bake/Broil Burner NOTE: If oven burner does not ignite, check oven gas shut-off position at the regulator. a. The approximate length of the flame of oven burner is a 1/2 inch distinct inner blue flame, figure 7. FIGURE 7 Bake/broil burner flame can be checked as follows: 1. Yellow flame on burner - open burner air shutter to the widest opening that will not cause the flame to lift or blow off the burner when cold. (See #2 on figure 8). Some yellow tipping on LP is normal. 2. Distinct blue flame but lifting - close burner air shutter to the point where it will not cause the flame to lift or blow off the burner when cold. (See #2 on figure 8). SHUTTER FIGURE 8-10-