Worthington CNG process pumps.

Transcription

1 Worthington CNG process pumps. Capacity to 5,000 gpm; heads to 475 feet. A proven and reliable pump for corrosive services in chemical, pulp and paper and general industry.

2 Longer lasting, easy to maintain and highly efficient pumps for the most rugged corrosive services. The CNG pump has proven itself through more than 25 years of service. This experience has been on some of the toughest applications such as evaporator service, furnace feed and fuming sulfuric acids. With the ever increasing demand on pump reliability you can continue to count on the "Old CarnpaigneC This line of corrosion-resistant pumps covers a wide range of services in the Chemical and Pulp & Paper industries. Twenty-nihe pumps are available for capacities up to 4,900 gpm, heads to 4 ft. For maximum interchangeability, all 29 sizes are mounted on only five basic bearing frames. These pumps are available with packed stuffing boxes or mechanical seals. The basic design allows for conversion from packed box operation to mechanical seal operation or vice-versa after the pump is installed. Design flexibility allows modifications for a wide range of temperatures and pressures. Bearings: pumps are equipped with anti-friction ball bearings. All bearings are sized to take the thrust and radial loads encountered and are designed for a minimum average life of years. system of deflectors, covers, and lip seals. Lubrication: standard is oil lubrication with a constant level oiler. Grease lubrication is also available. Impellers: semi-open with heavy vane sections ideal for slurries or solids. Balance ports and pump out vanes maintain low stuffing box pressure and balance thrust. Overall hydraulic design assures a low power requirement. Impeller is keyed to the shaft for added stability. Shafts: one piece and are ground on all critical surfaces. All shafts in this line are designed to transmit the power required and to withstand the radial reaction forces. In fact, on all pumps up to 0 gpm design capacity, the force on the shaft under worst conditions causes less than inch deflection of the shaft at the impeller Large pumps have proportionately lower deflection. materials of construction pa rt Casing Suction head Shaft Impeller Gland Packing Seal cage Material Graphite-impregnated Teflon (TFE*) Teflon* *Registered trademark of E. I. Dupont Improved Expeller Operating Performance integral bearing frame and adapter. This configuration assures greater rigidity and more accurate alignment. CNG PUMP WITH OPTIONAL EXPELLER Bearing protection: contaminants are excluded by a Lookat some of the features that have made the CNG the workhorse of the industry. Rugged frames: made of heavy cast iron with an STANDARD CNG PUMP 8 CNG-4 The expeller, positioned in a housing behind the impeller, is a sealing device that eliminates the need for packing or mechanical seals and a flush water system. The rotating expeller forces the pumped fluid away from the shaft and sleeve, eliminating leakage and virtually eliminating wear on these parts. Grease lubricated lip seals or packing rings are used as a static seal when the pump is not in operation. The 8 CNG 4 pump is an extension of the basic CNG line and also incorporates a large rugged bearing frame. The liquid end of the pump is separately supported so that the bearing frame, shaft, and impeller, together with the stuffing box head may be removed from the pump without disturbing the liquid end or suction and discharge piping connections. The expeller option can be retrofitted to existing CNG pumps in your plant. A retrofit kit consisting of an expeller and stuffing box can be introduced to your existing pump at low cost. The use of a twin volute construction drastically reduces bearing loading and shaft deflection over the complete pumping range and allows the pump to operate over wide capacity variations without difficulty. Part Impeller nut Slinger Tap bolts, studs and nuts Casing gasket Bearings Bearing frame Material Neoprene Durabla Ball Cast Iron

3 CNG pump coverage 0 0 CYCLE SPEEDS RPM t2 z n 3 Z 3 2 Expeller Option Available UW.tip jp. EDS RPM EH... f,,,,.=. : ','_. i---, 1 lp,,.. WM =IN... IIIIMMENElliiiel Wia EligiiiiiMIUMPIIMIYM MONO ii EIROWIP arli* Now "NW P 1 IIIII NM III,. o..; --...F...m.m... FM = MAI VIAMININIFAMMIEMIV e...,a1,,:-,:ongstiw.--. AMENEMIPPM'S... _,...6.,...i...: ,..,...m.,.,,,,,,,....,,,,..,...,... L 4, NI 1111/MMID111=MJ Ms.14grA...MINIIIIIMIMILS-ritiiiersiiiirli MESZIEWRZiiiii d1 II=1 MN ZE 70 `I ENII11 MIMAIPIMMIt. 1 CNG MINININCIONMIYAMII CNG ill III -...m=tdrard. =WM. IMMINERIIIMPEMNIFir ""0"11!raM P5IMIIMP1 11fUliPIVIM M1:02=1/1121M lakill111111pimmi =11 I=KASIMMIAMEN ni1=mm 111W,cor" n S 5 g p 2 V 25-55,,H CAPAC1TY-GPM Dimensions DISCHARGE i25* STD FLG pump size suct disch. S X Z P 111.t 1CNG-42 11/2 1 31/4 41/4 31/ CNG-52 11/2 1 31/4 41/2 33/ % 1CNG-64 11/2 1 27/8 51/4 41/4 153/4 43/4 1CNG-62 11/2 1 27% 51/4 41/4 19% 51/2 11/2CNG /2 31/ /8 19 7/8 6 11/2CNG /2 33/4 53/4 41/2 1/8 61/4 11/2CNG /2 33/4 61/4 5 1/8 1/4 61/4 1 1/2CNG /2 3% 71/ /2CNG /2 3% 8 63/4 6 2CNG /8 51/4 4 1/8 1/2 61/2 2CNG /4 61/2 51/4 % 6% 2CNG /2 61/4 % 61/2 pump size suet. 8 co co co CV C\I CO co.71- co co co S.Z CP 3CNG /4 21% 73/4 3CNG % 63/4 5 7/3 213/4 7 7/8 3CNG /4 71/2 61/2 21% 7% 2CNG /4 63/ /2 71/4 2CNG % /3 3CNG /4 71/4 51/4 27% 8% 3CNG-4 4 4% 83/4 71/2 267/8 7% 4CNG /4 81/2 7% 28% 9% 4CNG /2 9 81/2 31 9% 6CNG /4 31% 9% 6CNG-4 6 6% 83/4 31% 9% 6CNGL /8 1/4 31% 91/2 Authorized distributor: Dresser Pump Division 815 Uve Oak Drive Chesapeake, VA 233 DRESSER PUMP 4-B4F 791 PG

4 Worthington CNG process pumps with optional expeller Optional expeller Semi-open impeller Flanged connections Heads to 475 feet Capacities to 00 gpm Sizes 3/4 to 8"discharge The CNG pump has proved itself through more than years of service. This experience has been on some of the toughest applications such as evaporator service, furnace feed and fuming sulfuric acids. With the ever increasing demand on pump reliability you can continue to count on the "Old Campaigner." The CNG with an optional expeller is a line of corrosion-resistant pumps that covers a wide range of services in the Chemical, Grain Process and Pulp & Paper industries. Pumps are available for capacities up to 00 gpm, heads to 475 ft. Improved Expeller Operating Performance The expeller, positioned in a housing behind the impeller, is a sealing device that eliminates the need for packing or mechanical seals and a flush water system. The rotating expeller forces the pumped fluid away from the shaft and sleeve, eliminating leakage and virtually eliminating wear on these parts. Grease lubricated lip seals or packing rings are used as a static seal when the pump is not in operation. The expeller option can be retrofitted to existing CNG pumps in your plant. A retrofit kit consisting of an expeller and stuffing box can be introduced to your existing pump at low cost. Smooth-flow Design Open impellers of simple configuration with open passages permit abrasives to flow through freely. This simple design gives you lower first cost and lower repair costs. Wearing rings are eliminated. Long Bearing Life Bearings are anti-friction ball type, conservatively sized to take the thrust and radial loads encountered. Bearing protection is provided by a system of deflectors, covers and lip seals which prevent contaminants from reaching and entering bearings. Oil lubrication is standard construction. The pump is supplied with a constant-level oiler and oil slinger. Minimum Shaft Deflection Shaft is designed to transmit required power to the impeller and to withstand radial loads with minimum deflection. Easy Maintenance Trouble-free maintenance is assured through modern production control systems, procedures and equipment used in machining. Features Optional expeller* Acorn-type impeller nut Oil lubrication Impeller keyed to oversized rugged shaft Positive alignment by rabbeted fit Stuffing box easily converted from packing to mechanical seal One-piece solid shaft to minimize corrosion One-piece packing gland -4 STANDARD CNG PUMP CNG PUMP WITH OPTIONAL EXPELLER *Frame 3 and 4 pumps only.

5 CNG pump coverage 0 CO CYCLE SPEEDS RP.M. r...a Expeller Option Available J 11 3/4 0, := murf.mim. mews's, Miii E -,4.:24.111, E SP DS - - PM 11.1MMENIIIMWWMINEEM miimmommliiiim Ea=momm =MIIIIMMEN=MIIMIPMEIMMIIMMEN 'tact: mimminimmtimmoun Emaur MEMPERAPPAI I maimptp.26grammorinor,;:; museree.m VANIIIK34M!fal P'41./../.07/0"5/M1,41 ELMICIIIEWRZAMS/111115/111 LT_ 2 " o P- 0 3 imike Nollig3 -wigwam" CHO- 4 \ CPI 65 --inaumworimair --" F I C7k0--- MEMBrailiiiiMMINEME iial mmommigi mhorgrammi =MMENniitiNriNEralirAMM =111114WWAMEM...511/MIEMENIga ' ERZ INIMMINISAMPLAINIMMINIE ril= /%1M001 1n g/W,AKM/UNN 1 MUIMINffir.:011 ElMeOMMEMEM MIN =IMMI o04 e I a 2 2 DISCHARGE i2 STD FLG Dimensions ump size suct. disc pump size suct. disch. S X CP HL, 1CNG-42 11/2 1 31/4 41/4 31/ CNG-52 11/2 1 31/4 41/2 33/ /8 1CNG-64 11/2 1 2% 51/4 41/4 153/4 43/4 1CNG-62 11/2 1 2% 51/4 41/4 19% 51/2 1 1/2CNG /2 31/ /8 1 9% 6 1 1/2CNG /2 33/4 53/4 41/2 % 61/4 1 1/2CNG /2 33/4 61/4 5% 1/4 61/4 11/2CNG /2 3% 71/ /2CNG /2 3% 8 63/4 6 2CNG % 51/4 4% 1/2 61/2 2CNG /4 61/2 51/4 % 6% 2CNG /2 61/4 % 61/2 3CNG /4 21% 73/4 3CNG-74 5% 63/4 5 7/8 213/4 7 7/8 3CNG-84 43/4 71/2 61/2 21% 7% 2CNG-62 41/4 63/ /2 71/4 2CNG-4 3 7/ % 3CNG-62 51/4 71/4 51/4 27% 8% 3CNG-4 4% /2 26 7% 7% 4CNG-84 61/4 81/2 7% 28% 93/8 4CNG-4 51/2 9 81/2 31 9% 6CNG /4 31% 9% 6CNG-4 6% 83/4 31% 9% 6CNGL-4 6 1/8 1/4 31% 91/2 01 C C 1 CO CO CO CO (0 Materials of construction Part ateriai Material Part Material Casing CN7M Packing..Graphite-impregnated Teflon (TFE*) Casing gasket Durabla Suction head CN7M Seal cage Teflon* Bearings Ball Shaft CN7M Impeller nut CN7M Bearing frame Cast Iron Impeller CN7M Slinger Neoprene Expeller (OPT) CD4MCU Gland CN7M Tap bolts, studs and nuts CN7M Expeller stuffing box CD4MCU *Registered trademark of E. I. Dupont INGERSOLL-DRESSER PUMPS (After February 1, 1994) 821 Live Oak Drive 3900 Cook Boulevard Chesapeake, VA Chesapeake, VA PS2 190 KP Ingersoll-Dresser Pumps