AVPTC Multi-Position, Internal Txv

Transcription

1 Product Features Internal factory-installed thermal expansion valves for cooling and heat pump applications Variable-speed ECM blower motor ComfortNet Communicating System compatible Auto configuration of the airflow and tonnage in communicating mode Provides constant CFM over a wide range of static pressure conditions independent of duct system CFM indicator Fault recall of six most recent faults Provides adjustable low CFM for efficient fan-only operation Improved humidity and comfort control Built-in compatibility with multi-stage heat pump and cooling applications All-aluminum evaporator coil Cabinet air leakage less than.0% at 1.0 inch HO when tested in accordance with ASHRAE standard 19 Cabinet air leakage less than 1.% at 0.5 inch HO when tested in accordance with ASHRAE standard 19 kw 5 kw electric heater kits Horizontal or vertical configuration capabilities Rigid SmartFrame cabinet 1" depth for easier attic access DecaBDE-free thermoplastic drain pan with secondary drain connections Screw-less sides and back helps to reduce condensation when installed in humid locations Foil-faced insulation covers the internal casing to reduce cabinet condensation Galvanized, leather grain-embossed finish Glue-less cabinet insulation retention Tool-less filter access AHRI certified; ETL listed Multi-Position, Internal Txv Variable-Speed ECM Based Comfortnet Compatible Air Handler 1½ to 5 Tons * Complete warranty details available from your local dealer or at To receive the 10-Year Parts Limited Warranty, online registration must be completed within 60 days of installation. Online registration is not required in California or Quebec. SS-G /1 Supersedes 1/1

2 Nomenclature A V P T C 18 B 1 AA 1 5 6, ,1 Brand Engineering* A Single- Piece Major/Minor Revisions Airhandler *Not used for inventory management Unit Application Refrigerant Charge R Multi Position PSC Motor = R- 10A S Multi Position EEM Motor V Multi Position Variable- Speed Electrical Motor- Commuminacating 1 08/0V, 1 Phase, 60 Hz Cabinet Finish Cabinet Width U Unpainted B = 17½" P Painted C = 1" D = ½" Expansion Device F Flowrator Nominal 1SEER T Expansion Device 18 = 1½ Tons = ½ Tons = Tons 8 = Tons 0 = ½ Tons 60 = 5 Tons Communications 6 = Tons C = ComfortNet TM Compatible Accessories Downflow Kits Filters DFK-B DFK-C DFK-D B1** 0C1** D1** 6C1** 8D1** 8C1** 60D1** Chassis Part# Size B ALFH1601E 16.0" x 0.0" C ALFH19101E 19.5 x 0.0 D ALFH01E.0 x 0.0 Single Point Kit ** Model HKR-15C HKR-0C HKR-1C SPW-01 X X X ** Must be installed along with any of the above compatible heat kits. This kit will fit any air handler as long as a compatible heat kit is installed in the unit. SS-G

3 Specifications Nominal Ratings B1A* 0C1A* 6C1A* C1A* 8D1A* 8D1A* 60D1A* Cooling (BTU/h),000 0,000 6,000,000 8,000 8,000 60,000 Blower Diameter 10⅝" 10⅝" 10⅝" 10⅝" 10⅝" 10⅝" 11⅝" Width 6" 8" 10⅝" 10⅝" 10⅝" 10⅝" 10⅝" Coil Drain Connection FPT ¾" ¾" ¾" ¾" ¾" ¾" ¾" Service Valve Liquid ⅜" ⅜" ⅜" ⅜" ⅜" ⅜" ⅜" Suction ¾" ⅞" ⅞" ⅞" ⅞" ⅞" ⅞" Electrical Data Voltage 08/0 08/0 08/0 08/0 08/0 08/0 08/0 Min Circuit Ampacity.9/.9.9/.9 8.6/8.6 Max. Overcurrent Device (amps) Minimum VAC Maximum VAC Blower Motor A HP ½ ½ ¾ ¾ ¾ ¾ 1 Ship Weight (lbs) SS-G

4 Dimensions 1.6" (.1 cm) 1.5" (.68 cm).08" (7.8 cm) 1".50" (11. cm).91" (7.9 cm).9" (7. cm) 7.5" (19.1 cm) 5." (1. cm) 9.1" DRAIN PORT DETAIL.55" (1.0 cm) C B.55" (1.0 cm).1" (7.9 cm) 1." (.6 cm) 11." (8.70 cm).55" (1.0 cm) PLASTIC BREAKER COVER 1.8" (.6 cm) LOGO LOCATION.17" (5.51cm) SUCTION TUBE LIQUID LINE A G INLET TUBE SEE DRAIN PORT DETAIL H E D 1.7" (.9 cm) F INLET (FRONT VIEW) 1.7" (.9 cm) 1" (.5 cm) 19.5" (9.5 cm) INLET (RIGHT SIDE VIEW).55" (1.0 cm) Model A B C D E F G H B1 5 16⅜ 17½ ³ ₁₆ 8¹³ ₁₆ 11¹⁵ ₁₆ 0C1 9 19¹⁵ ₁₆ ¹¹ ₁₆ 10½ 1⅜ 6C1 9 19¹⁵ ₁₆ ¹¹ ₁₆ 10½ 1⅜ D1 58 ⁵ ₁₆ ½ 8³ ₁₆ 5³ ₁₆ 1³ ₁₆ 1⁵ ₁₆ 1⅜ 8C1 9 19¹⁵ ₁₆ ¹¹ ₁₆ 10½ 1⅜ 8D1 58 ⁵ ₁₆ ½ 8³ ₁₆ 5³ ₁₆ 1³ ₁₆ 1⁵ ₁₆ 1⅜ 60D1 58 ⁵ ₁₆ ½ 8³ ₁₆ 5³ ₁₆ 1³ ₁₆ 1⁵ ₁₆ 1⅜ SS-G

5 Airflow Data Cooling / Heat Pump Airflow B A Low B Low C Low D Low A High B High C High D High C A Low B Low C Low D Low A High B High C High D High C A Low B Low C Low D Low A High B High C High D High D A Low B Low C Low D Low A High B High C High D High C A Low B Low C Low D Low A High B High C High D High SS-G 5

6 Airflow Data (cont.) Cooling / Heat Pump Airflow (cont.) 8D A Low B Low C Low D Low A High B High C High D High D A Low B Low C Low D Low A High B High C High D High Note: When applying a humidistat (normally closed), refer to the installation and operating instructions. The humidistat can adjust the cooling airflow to 85%. Electric Heat Airflow HTR kw B1A* 0C1A* 6C1A* D1A 8C1A* 8D1A 60D1A ON ON ON NR 850** NR NR NR 5 ON ON OFF ON OFF ON ON OFF OFF OFF ON ON OFF ON OFF NR NR * NR NR 1500 NR 1500 NR NR OFF OFF ON 0 NR NR NR or 5* OFF OFF OFF NR NR NR NR NR Note: Airflow data shown applies to the electric heat only in either legacy mode or communicating mode operation NR - Not Rated * Within thermostat user menu, CTK0* communicating thermostat will display 0kW for OFF- OFF- ON dipswitch selection, 1kW for OFF-OFF-OFF dipswitch selection. For match up with a ton outdoor unit: Heater kit application shall not exceed 10 kw. Airflow for 5 kw up to 10 kw heater kits shall be set to 850 cfm speed tap of ON-ON-ON. For match up with a ton outdoor unit: Heater kit application shall not exceed 15 kw. Airflow for 5 kw up to 15 kw heater kits shall be set to 100 cfm speed tap of ON-OFF-ON. For match up with a.5 ton outdoor unit: Heater kit application shall not exceed 0 kw. Airflow for 5 kw up to 0 kw heater kits shall be set to 1500 cfm speed tap of ON-OFF-OFF ** kw heater kit is not applicable for this indoor application. 6 SS-G

7 Heat Kit Data Models B1A* 0C1A* 6C1A* HKSC19C#* 8C1AA HKSC19C#* D1A* HKSC0D#* 8D1A* HKSC0D#* HKSC5DC* 8D1A* HKSC0D#* HKSC5DC* Circuit 1 Circuit Single-Point Kit Amps MCA¹ MOP² Amps MCA¹ MOP² MCA¹ MOP².9/.9 18/1 7/0 0/0 /6 1/7 8/55 5.0/ /60.0.9/.9 18/1 7/0 /6 1/7 8/55 7/8 0/0 9/107 9/107 9/107 9/ /1 7/8 95/ /1 15/150 15/150 ¹ Minimum Circuit Ampacity (Heater Amps + Motor Amps) X 1.5 ² Maximum Overcurrent Protection =.5 X Motor Amps + Heater Amps ^ Circuit 1: Single-phase for Air Handlers Circuit : Three-phase for HKR Heater Kits * Revision level that may or may not be designated C = Circuit Breaker Option indicates Not Required HKA meets the new UL1995 requirements for 15 and 0KW heaters SS-G 7

8 Wiring Diagram HTR1 TL PLM 1 PU M1 R 5 M WH L1 L ONE (1) ELEMENT ROWS HTR TL HTR1 TL PLM 1 PU M1 M R M M 5 WH L1 L TWO () ELEMENT ROWS HTR1 TL HTR TL PLM HTR TL 1 YL YL PU M1 M M1 M M M R1 R BR 5 WH 6 7 YL 8 9 L1 L L1 L THREE () ELEMENT ROWS HTR1 TL HTR TL HTR TL YL PLM HTR TL 1 PU M1 M M5 M7 YL M M M6 M8 R1 R BR 5 WH 6 7 YL 8 9 FOUR () ELEMENT ROWS L1 L L1 L COLOR CODES: PK - PINK BR - BROWN WH - WHITE - UE GY - GRAY - RED YL - YELLOW OR - ORANGE PU - PURPLE GN - GREEN - ACK NOTE: WHEN INSTALLING HEATER KIT, ENSURE SPEED TAP DOES NOT EXCEED MINIMUM OWER SPEED (MBS) SPECIFIED FOR THE AIRHANDLER/HEATER KIT COMBINATION ON THIS UNIT'S S&R PLATE. AFTER INSTALLING OPTIONAL HEAT KIT, MARK AN "X" IN THE PROVIDED ABOVE. PL1 PL SEE NOTE 7 MARK ACCOING TO NUMBER OF HEATER ELEMENT ROWS INSTALLED. NO MARK INDICATES NO HEAT KIT INSTALLED. 0 VA TRANSFORMER, SEE NOTE 1 0 VAC 08 VAC VAC COM 1 WH BR 1 GY LEARN SEE NOTE 6 TH TR COM V A FUSE CONT FAN 7 SEGMENT DIAGNOSTIC DEHUM DISPLAY CFM LED O SEE NOTE 6 RX LED Y Y1 W W1 G C S1 S S S S5 S6 S7 S8 S9 S10 S11 S1 S1 R DIP SWITCHES TWO-STAGE INTEGRATED CONTROL MODULE 1 CIRCUIT MOTOR CONNECTOR ECM MOTOR HARNESS 1 CIRCUIT HEATER CONNECTOR SEE NOTE 5 FAULT RECALL SEE NOTE 6 STATUS LED AF SELECT TRIM % 1 COOL AF PROFILE DEHUM ENAE TRIM ENAE HTR KIT(KW) GN CAS SEE NOTE 8 V THERMOSTAT CONNECTIONS CIRCULATOR OWER 1 GN 5 V THERMOSTAT CONNECTIONS R W1 W Y1 Y G O DISCONNECT DEHUM C L1 FUSE A TO MICRO L1 TH W1 (1) W () CAS (1) CAS () +VDC (1) RX () TX () () TR COM INDOOR AIR CIRCULATOR WR 08/0 VAC INTEGRATED CONTROL MODULE L L 0 VA TRANSFORMER VAC HEAT SEQUENCER R1 HEAT SEQUENCER R CONDENSATE SWITCH INDOOR AIR CIRCULATOR WR LOW VOLTAGE (V) LOW VOLTAGE FIELD HI VOLTAGE (0V) HI VOLTAGE FIELD JUNCTION TERMINAL INTERNAL TO INTEGRATED CONTROL EQUIPMENT FIELD FIELD SPLICE RESISTOR OVERCURRENT PROT. DEVICE PLUG CONNECTION NOTES: 1. PLACE RED WIRES ON TRANSFORMER TERMINAL FOR 08 VAC OPERATION.. MANUFACTURER'S SPECIFIED REPLACEMENT PARTS MUST BE USED WHEN SERVICING.. IF ANY OF THE ORIGINAL WIRES AS SUPPLIED WITH THIS UNIT MUST BE REPLACED, IT MUST BE REPLACED WITH WIRING MATERIAL HAVING A TEMPERATURE RATING OF AT LEAST 105 C. USE COPPER CONDUCTORS ONLY.. UNIT MUST BE PERMANENTLY GROUNDED AND CONFORM TO N.E.C AND LOCAL CODES. 5. TO RECALL THE LAST 6 FAULTS, MOST RECENT TO LEAST RECENT, DEPRESS SWITCH FOR MORE THAN SECONDS WHILE IN STANDBY (NO THERMOSTAT INPUTS) 6. RED STATUS LED PROVIDES NETWORK STATUS. GREEN RX LED INDICATES NETWORK TRAFFIC. USE LEARN BUTTON TO RESET NETWORK. 7. DISCA CONNECTOR PL1 WHEN INSTALLING OPTIONAL HEAT KIT. 8. THE CONDENSATE ALARM SWITCH (CAS) TERMINALS CAN ONLY BE UTILIZED WITH COMMUNICATING MODE SETUPS AND MUST BE ENAED WITH A COMMUNICATING THERMOSTAT. THIS FEATURE IS NOT OPERATIONAL WITH LEGACY SYSTEMS. NOTE: The five element, 5 kw heater kit is not shown above. 010A00071-A Wiring is subject to change. Always refer to the wiring diagram or the unit for the most up-to-date wiring. Warning High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. Goodman Manufacturing Company, L.P., reserves the right to discontinue, or change at any time, specifications or designs without notice or without incurring obligations. 01 Goodman Manufacturing Company, L.P. Houston, Texas Printed in the USA. 8 SS-G