Bagless upright. vax.co.uk. Vax Careline: (UK) (ROI) VZL-6017 Series. Vax model number: Version 3.2

Transcription

1 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 1 Vax Careline: (UK) (ROI) agless upright Vax model number: VZL-6017 Series !! Version 3.2 vax.co.uk Please read carefully before using this cleaner. lways fully extend the mains cable before use. Retain for future reference.

2 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 2 vax.co.uk 1. Diagram 1 Handle NOTE: Some parts may vary according to model. Please check inside flap of box for more details. 2 On/off switch Ensure that the plug is inserted securely into the electrical socket before pressing the on/off switch. 3 Hose 4 Dirt container release button Located at the front of the unit, the dirt container can then be removed for emtying. 5 Dirt container Locked onto the front of the unit 6 Hose handle 7 Power cord reel window To rewind the cord, hold onto the plug and press the button at the top of the cord reel. 8 Headlight IMPORTNT: Disconnect the cleaner from the electrical socket before removing or installing the headlight. 9 Nozzle control knob Turn knob to correct setting for height of carpet being cleaned 10 Furniture guard The guard helps prevent cleaner from marking furniture 11 rushbar on/off pedal foot operated pedal located on the base of the cleaner 12 rushbar on/off indicator The indicator shows red in the rushbar On window then the brushbar is in operation. The indicator will show red in the rushbar Off window when it is switched off. WRNING: This machine has a rotating! brushbar. The brushbar must NOT be rotating when cleaning lino or hard floors. Switch the brushbar off to prevent damage to lino, parquet and other hard flooring. Please see the operational details. NOTE: Vax can not be held responsible for damage to hard floors, including lino, if the customer fails to switch the brushbar off on these surfaces. 13 HEP final filter IMPORTNT: Do not rinse or wash the HEP filter 14 2-in-1 tool Dusting brush: for delicate surfaces Upholstery tool: for carpet, upholstery and stairs etc. 15 TurboTool Great for picking up pet hair and for use on stairs, upholstery and car interiors. 16 Crevice tool Can be used in tight spaces, corners and along edges in such places as upholstered furniture, stairs and skirting boards. 17 Hose/tool holder 18 Extension tubes Used to give extra length to the hose 19 Power cord reel Cord storage 20 Wheels 21 Unit recline pedal Step on lever to lower handle to operating or low positions 22 Cord rewind button Press button to rewind cord for storage. Hold plug until cord is rewound 23 Hard floor tool (some models only) 2 parts overview

3 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 3 Vax Careline: (UK) (ROI) Safety Information For household use only When using the vacuum cleaner, basic safety precautions should always be observed, including the following: 1. Only use the vacuum cleaner indoors on dry surfaces. 2. Turn off the vacuum cleaner controls before connecting or disconnecting from the electrical socket. 3. lways unplug the vacuum cleaner before connecting or disconnecting the vacuum hose and accessories. 4. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 5. Use only as described in this manual. Use only the manufacturer s recommended attachments. 6. Do not use the vacuum cleaner if it has been dropped, damaged, left outdoors or dropped into water. Do not use the vacuum cleaner with a damaged cord or plug. If the supply cord is damaged, it must be replaced by the manufacturer or a recommended Service gent to avoid hazard and invalidating the guarantee. 7. Do not pull or carry by the cord. Do not use the cord as a handle, close a door on the cord or pull the cord around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces. 8. Do not handle the plug or vacuum cleaner with wet hands. Do not use outdoors or on wet surfaces. 9. Do not put any objects into openings. Do not use with any openings blocked and do not restrict air flow. Keep all openings free of dust, lint, hair or anything that may reduce airflow. 10. Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts. 11. Do not pick up hot coals, cigarette butts, matches or any hot, smoking or burning objects. 12. Do not pick up flammable or combustible materials (lighter fluid, petrol, kerosene, etc) or use in the presence of explosive liquids or vapours. 13. Do not vacuum up harmful or toxic material (chlorine bleach, ammonia, drain cleaner, etc). 14. Do not vacuum up hard or sharp objects such as glass, nails, screws, coins, etc. 15. Do not use without the filters in place. 16. Take extra care when vacuuming on stairs. 17. Keep vacuuming area well lit. 18. Store the vacuum cleaner indoors in a cool, dry area. 19. Turn off the on/off switch before unplugging the vacuum cleaner. 20. Use only CE-approved 13 amp extension cords. Non-approved extension cords may overheat. Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over. WRNING: lways switch off and unplug the! vacuum cleaner from the electrical socket before assembling, opening or emptying the dirt container, or before connecting/disconnecting the attachments. CUTION: The vacuum cleaner is a very powerful! unit. efore plugging the cord into the electrical socket, make sure the switch is in the off position. Hold the vacuum cleaner firmly when starting and in use. IMPORTNT: If the inlet, hose or extension tube! is blocked, switch off the vacuum cleaner and remove the blockage(s) before re-starting the vacuum cleaner. IMPORTNT: Cleaning filters regularly maintains! vacuum performance. Make sure all filters are replaced before using. This vacuum cleaner is intended for household use only and not for commercial or industrial use. PLESE KEEP THESE INSTRUCTIONS FOR FURTHER USE. Motor Thermostat IMPORTNT: The motor is equipped with a! thermal cut-out. If for any reason, the vacuum cleaner should over-heat, the thermostat will automatically turn the unit off. Should this occur, unplug the vacuum cleaner from the electrical socket and turn off the switch. Remove the dirt container and empty. Clean the filters. llow the cleaner to cool for approximately one (1) hour. To re-start, plug into an electrical socket and switch back on. safety information 3

4 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 4 vax.co.uk 3. How to assemble ttach handle Using a crosshead screwdriver, remove (2) screws from the top of the upper housing assembly (Fig.3/1). Position tools Place smaller diameter end of wand () into bottom of holder. Snap wand into clip at top. Repeat with other wand. Crevice tool () fits into one of the extension wands. Fit combination tool (C) into storage area on side of cleaner as shown (Fig.3/4). C Fig.3/1 Insert handle section () into upper housing assembly. Push down firmly until you hear a click (Fig.3/2). Fig.3/4 Fit TurboTool () into recessed area on front of cleaner. Pivot toward handle to snap in place (Fig.3/5). Fig.3/2 Fasten (2) screws on either side of handle base (Fig.3/3). Fig.3/5 Fig.3/3 4 how to assemble

5 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 5 Vax Careline: (UK) (ROI) How to operate On/off switch Plug cord into electrical socket. To turn cleaner ON, push ON/OFF switch once. To turn cleaner OFF, push switch again (Fig.4/1). NOTE: To prevent cord from whipping, hold plug until cord is rewound. Fig.4/1 rushbar switch The cleaner is shipped with the brushbar in the OFF position. To turn the brushbar ON, step on the pedal (). The indicator () will show red in the brushbar on window (Fig.4/2). WRNING: The brushbar must NOT be rotating! when cleaning hard floors. Switch the brushbar off to prevent damage to lino, parquet and other hard flooring. NOTE: s a precaution Vax recommends that you raise the brushbar as well as switching it off for use on lino and hard floorings Fig.4/3 Transporting cleaner To move your cleaner from room to room, put handle in upright position, tilt cleaner back on rear wheels and push forward (Fig.4/4). Fig.4/4 Handle positions The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating position for general operation on carpet and floors; low for reaching under low furniture. Step on unit recline pedal to lower unit (Fig.4/5). 1 Fig.4/2 2 Cord rewind Grasp the end of the plug and pull to release cord from cord reel. fter desired cord length is reached, the cord will lock into position. Pull cord all the way out each time cleaner is used to avoid heating of cord (Fig.4/3). Fig.4/5 3 how to operate 5

6 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 6 vax.co.uk rushbar height adjust The cleaning of carpet and rugs takes place at the nozzle (). When it is necessary to raise and lower the nozzle for various carpet pile heights, turn the brushbar height adjuster knob () to the desired setting (Fig.4/6). Fig.4/6 Settings For maximum cleaning performance, the following carpet height settings are recommended (Fig.4/7): Lowest setting for all types of carpet. Higher settings: for very deep pile carpet, where easier pushing effort is desired, while maintaining good cleaning performance. NOTE: If the cleaner is difficult to push, turn knob to the next higher setting. WRNING: The brushbar must NOT be rotating! when cleaning hard floors. Switch the brushbar off to prevent damage to lino, parquet and other hard flooring. rushbar on/off The brushbar shuts off automatically for tool use, when the cleaner is in the upright position. To manually shut off the brushbar for cleaning hard floors, step on the pedal (). The indicator () will show red in the brushbar off window. To turn the brushbar on, step on the pedal again. The indicator will show red in the brushbar on window. (Fig.4/8) HIGH Fig.4/7 LOW 5. ccessories Select correct tool (Fig.5/1). Dusting brush/upholstery tool: use with brush for carved furniture, table tops, books, lamps, lighting fixtures, venetian blinds, skirting boards and shutters. Remove brush to clean upholstered furniture, draperies, mattresses, clothing, and carpeted stairs.. TurboTool: may be used for upholstered furniture, mattresses, clothing, automobile interiors and carpeted stairs. C. Crevice tool: may be used in tight spaces, corners and along edges in such places as upholstered furniture, stairs and skirting boards. D. Extension tubes: are used to give extra length to your hose. Use them with any of the above tools. E. Hard floor tool: (available on some models only) use on hard surface floors. Fig.5/1 C ttach extension tube and tools ttach extension tube or tool to the hose (). ttach tool to extension tube () by pushing it firmly onto the wand. Twist extension tube or tool slightly to tighten or loosen the connection (Fig.5/2). D E Fig.5/2 Fig.4/8 6 how to operate / accessories

7 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 7 Vax Careline: (UK) (ROI) Dusting brush/upholstery tool: Slide brush to remove. To replace brushes, align brushes, align bottom of brush with grooves () on tool. Slide brush into place (Fig.5/3). lign end of extra reach hose with projections () over slots on dirt duct (C). Slide hose into slots and twist hose to lock it into place. lign end of hose with projections (D) over slots (E) on stretch hose. Slide hose into slots and twist hose to lock it into place (Fig.5/5). (To detach hose, reverse procedure.) D C Fig.5/3 Stair cleaning Use the hose and TurboTool for stair cleaning. Clean from bottom to top CUTION: To avoid personal injury or! unnecessary wear to carpet, and to prevent the cleaner from falling, always place it at bottom of stairs. Stretch hose (some models only) The stretch hose provides easier cleaning of stairs and hard to reach places. Follow the steps below for attaching and detaching the stretch hose. Turn cleaner OFF before disconnecting and connecting hose. Remove hose end from dirt duct () (Fig.5/4). Fig.5/5 E ttach wands or tools to the other end of hose. Note: Hose must be connected to dirt duct and hose tube after removing stretch hose for carpet or floor cleaning. Fig.5/4 accessories 7

8 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 8 vax.co.uk 6. Maintenance Familiarise yourself with these home maintenance! tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness. Holding dirt container over a bin, press dirt container door release button () to open dirt container door () (Fig.6/3). Emptying the dirt container Empty the dirt container before the dirt reaches the fill line (). Place the cleaner in the upright position before removing the dirt container (Fig.6/1). Fig.6/3 Close door and press dirt container door release button to latch dirt container door closed. Place bottom of dirt container into cleaner body first. Pivot container into cleaner body (Fig.6/4). Fig.6/1 Disconnect cleaner from electrical socket. Do not use cleaner without dirt container or filters in place. CUTION: Very fine materials, such as plaster dust or cornstarch, may seal the filter and cause a reduction in performance. When using the cleaner for this type of dust, empty the container and clean the filters often. Press dirt container release button () and pivot container out (Fig.6/2). Fig.6/4 Press on dirt container release button while firmly pressing on dirt container. Release button in order for it to return to proper position and lock the dirt container into place (Fig.6/5). Fig.6/2 Fig.6/5 8 maintenance

9 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 9 Vax Careline: (UK) (ROI) Cleaning the filters Cyclonic filter assembly IMPORTNT: Disconnect cleaner from electrical! socket. Do not operate cleaner without dirt container or filters in place. Remove dirt container as previously described (Fig.6/2). Twist filter assembly () counterclockwise. Remove assembly from dirt container (Fig.6/6). Remove black foam filter. Rinse filter frame cartridge and foam filter under cold water (Fig.6/8). Fig.6/6 Dirt and debris can be cleaned from the filter assembly by brushing with the cleaner s combination tool. Place the filter assembly on the dirt container, aligning (3) tabs () on filter with (3) slots on dirt container () and twist it clockwise to secure into position. Press dirt container door release button (C) to latch dirt container door closed (Fig.6/7). Fig.6/8 llow both filter frame and filter to air dry for 24 hours before replacing filter into filter frame. Reposition filter frame cartridge by inserting tabs into slots on back of housing. Rotate filter cartridge frame up toward top of housing and snap closed. HEP final filter IMPORTNT: Disconnect cleaner from electrical! socket. Do not operate cleaner without dirt container or filters in place. With fingers in slots, pull filter frame () straight out (Fig.6/9). Fig.6/7 C Fig.6/9 Replace dirt container as described in Figs.6/4. Secondary filter IMPORTNT: Disconnect cleaner from electrical! socket. Do not operate cleaner without dirt container or filters in place. Remove dirt container as previously described (Fig.6/2). With thumb and forefinger, slide latch () located at the top of the housing to the right and pull down to remove gray filter frame. Dirt and debris can be cleaned from the filter cartridge by brushing with the cleaner s combination tool, IMPORTNT: Do not rinse or wash the HEP! filter cartridge. maintenance 9

10 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 10 vax.co.uk Headlight IMPORTNT: Disconnect cleaner from electrical! socket. Removing headlight lens Press unit recline pedal and place handle in low position. Using a crosshead screwdriver, remove the screw as shown and lift off lens (Fig.6/10). elts IMPORTNT: Disconnect cleaner from electrical! socket. WRNING: rushbar can start suddenly. Unplug! cleaner before turning it over. The belts are located under the bottom plate of the cleaner and should be checked from time to time to be sure they are in good condition. Replacing flat belt Replace belt if it is stretched, cut or broken. To check the flat belt, refer to Fig.6/13. Removing bottom plate Place handle in low position and turn cleaner over so bottom side is facing up. Remove the 6 screws as shown with a Crosshead screwdriver. Lift off bottom plate (Fig. 6/13). Fig.6/10 Installing headlight bulb Pull old bulb straight out of socket. Push new bulb straight into socket until locked in place. Excessive force is not required. (Fig.6/11). For replacement bulbs please call Vax Careline. Fig.6/13 Removing belt Remove used belt () from large pulley () and discard (Fig.6/14). Fig.6/11 Replacing headlight lens Reposition lens and secure with the screw (Fig.6/12). Fig.6/14 Fig.6/12 Positioning belt With lettering on outside of belt, slide new belt over motor shaft (). Place other end of belt over large pulley () while rolling the pulley in direction shown. Turn brushbar making sure belt turns freely and is not pinched between brushbar and agitator shield (Fig.6/15). Reposition bottom plate and 6 crosshead head screws. 10 maintenance

11 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 11 Vax Careline: (UK) (ROI) Insert brushbar through belt an position belt in groove () on brushbar (Fig.6/18). Fig.6/15 Tighten screws securely (Fig.6/16). Fig.6/18 Fig.6/16 Inspecting the belt The belt is designed to last for a long time and is not normally replaced. However, if the belt is cracked, gouged or broken, it should be replaced. Slide flat belt off large pulley as shown in Fig.6/14. To remove belt, slide back of belt over pulley (). Then firmly pull on belt and snap it out. Discard used belt. To install new belt (with lettering on outside of belt), slide back of belt over pulley and pull front of belt toward groove () next to pulley. elt will pop into place (Fig.6/17). rushbar IMPORTNT: Disconnect cleaner from electrical! socket. WRNING: rushbar can start suddenly. Unplug! cleaner before turning it over. Replacing brushbar When agitator brushes are worn, the brushbar should be replaced. Inspecting brushbar To check condition of brushes, move edge of a card across bottom plate while turning brushbar. To maintain cleaning effectiveness, replace brushbar if brushes do not touch card (Fig.6/19). Fig.6/19 Fig.6/17 maintenance 11

12 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 12 vax.co.uk 7. Troubleshooting! WRNING: To reduce the risk of personal injury, unplug vacuum cleaner before servicing. PROLEM: Cleaner won t run Cause: Not corectly plugged into electrical socket. Solution: Plug in firmly. Cause: No electricity in electrical socket Solution: Check fuse or circuit. Cause: lown fuse/tripped circuit. Solution: Reset circuit or replace fuse. Cause: Motor thermostat tripped. Solution: Switch off and unplug the vacuum cleaner. Leave for one (1) hour. See page 3. PROLEM: Cleaner/tools won't pick up Cause: roken or worn belt. Solution: replace belt. Cause: rushbar worn. Solution: Replace brushbar. Cause: Dirt container full. Solution: Empty dirt container. Cause: Incorrect brushbar height setting. Solution: Move brushbar height adjuster to lower setting. Cause: lockage in air flow passages. Solution: Clear blockage. 8. UK Service & Help Vax Careline: (UK) (ROI) Monday-Friday 8.30am to 6.30pm Saturday-Sunday 9.00am to 5.00pm If you have queries or concerns about using your Vax, call the Vax Careline. Calls are charged at the UK local rate. Please make a note of the serial number and model number of the vacuum cleaner before calling. For the nearest Service gent, please call the Vax Customer Careline or visit vax.co.uk 9. Consumables To purchase spares and accessories, please visit vax.co.uk elt kit Type 9/: Guarantee will only be valid with the use of genuine Vax spares and accessories. PROLEM: Cleaner hard to push Cause: Incorrect brushbar height setting. Solution: Move carpet height adjuster to higher setting. PROLEM: Smoky/burning smell detected Cause: elt broken or stretched. Solution: Replace brushbar as described in section 6. PROLEM: TurboTool brushbar won t turn Cause: Too much pressure being applied to tool. Solution: Continue using tool applying light pressure. Cause: lockage in turbine channel. Solution: Remove blockage. Cause: Low cleaner suction. Solution: Check items under Cleaner/tools won t pick up above. 12 troubleshooting/ uk service & help

13 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 13 Vax Careline: (UK) (ROI) Technical Specification Voltage: V ~50Hz Wattage: 1500W Capacity: 2.6l Filters: Pre-motor filter HEP post motor filter Cord Length: 8.3m Weight: 11.8kg Subject to technical change without notice. technical specification 13

14 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 14 This page has been left intentionally blank. 14

15 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 15 Vax Careline This page has been left intentionally blank. 15

16 VZL-6017 User Guide v3.2_vax VZL /01/ :25 Page 16 EEC STTEMENT OF COMPLINCE Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the VZL-6017 Mach 7 series is manufactured in compliance with the following Directives: Safety: 2006/95/EC Low Voltage Directive EMC: 2004/108/EC Electromagnetic Compatibility Directive Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local uthority or retailer for recycling advice. Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK info@vax.co.uk - website: vax.co.uk