Read Only Copy Not For Distribution. Chapter 19. Referenced Standards 19.1 REFERENCED STANDARDS 19.2 STANDARDS ORGANIZATIONS

Transcription

1 19.1 REFERENCED STANDARDS Referenced Standards Chapter 19 Table 19.1 lists the standards that are referenced within the requirements of this Code. Table 19.1 shows the designation number of the standard, its edition date, a date if reaffirmed, any addendums or amendments, its title, and the Sections and/or Tables in the Code where the standard is referenced STANDARDS ORGANIZATIONS AHAM ANSI Association of Home Appliance Manufacturers th Street, NW, Suite 402 Washington, DC USA American National Standards Institute 1899 L Street, NW, 11th Floor Washington, DC USA fax: ASHRAE ASHRAE Headquarters 1791 Tullie Circle, NE Atlanta, GA USA fax: ASME ASSE ASTM AWWA CISPI CSA ASME Two Park Avenue New York, NY USA ASSE International Hickory Creek Drive, Suite 220 Mokena, IL USA fax: ASTM International 100 Barr Harbor Drive P.O. Box C700 West Conshohocken, PA USA American Water Works Association 6666 W. Quincy Avenue Denver, CO USA fax: Cast Iron Soil Pipe Institute 3008 Preston Station Drive Hixson, TN USA CSA Group 178 Rexdale Boulevard Toronto, ON, Canada, M9W 1R FM IAPMO ISEA MSS NFPA NSF PDI UL FM Global 270 Central Avenue Johnston, RI USA fax: IAPMO 4755 E. Philadelphia Street Ontario, CA USA fax: International Safety Equipment Association 1901 North Moore Street Arlington, VA USA fax: Manufacturers Standardization Society 127 Park Street, NE Vienna, VA USA NFPA 1 Batterymarch Park Quincy, MA USA fax: NSF International 789 N. Dixboro Road P.O Ann Arbor, MI USA fax: Plumbing and Drainage Institute 800 Turnpike Street - Suite 300 North Andover. MA USA Underwriters Laboratories Inc. 333 Pfingsten Road Northbrook, IL USA National Standard Plumbing Code - Illustrated 371

2 AHAM DW Dishwashers Table VII, AHAM FWD Food Waste Disposers Table VII, AHAM HLW Performance Evaluation Procedures for Household Clothes Washers ANSI Z (R2005) Sanitation - Non-sewered Waste-Disposal Systems - Minimum Requirements ANSI Z Gas Water Heaters - Volume I, Storage Water Heaters with Input Ratings of 75,000 Btu per Hour or Less Table VII, , Table X Table VII, ANSI Z /CSA 4.1 Refer to ANSI Z or CSA 4.1 Table VII, ANSI Z Gas Water Heaters - Volume III, Storage Water Heaters with Input Ratings above 75,000 Btu Per Hour, Circulating and Instantaneous Table VII, ANSI Z /CSA 4.3 Refer to ANSI Z or CSA 4.3 Table VII, ANSI Z (R2008) Relief Valves for Hot Water Supply Systems Table VIII, , Figure ANSI Z21.22/CSA 4.4 Refer to ANSI Z21.22 or CSA 4.4 Table VIII, , Figure ANSI/ISEA Z ASHRAE Standard (R2013) American National Standard for Emergency Eyewash and Table V, Shower Equipment Table Note (17), 7.24 Methods of Testing for Rating Drinking-Water Coolers with Self-Contained Mechanical Refrigeration ASME A (R2013) Scheme for the Identification of Piping Systems 2.27, ASME A ASME A (R2010) ASME A ASME A Air Gaps in Plumbing Systems (for Plumbing Fixtures and Water-Connected Receptors) Air Gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances Stainless Steel Drainage Systems for Sanitary DWV, Storm, and Vacuum Applications, Above- and Below- Ground Plumbing Fixtures with Pumped Waste and Macerating Toilet Systems Table IX, , Table IX, , Table I, Table 3.5, Table 3.6, Table 3.7, Table X, 7.4.8, ASME A /CSA B45.9 Refer to ASME A or CSA B45.9 Table X, 7.4.8, ASME A Water Heater Relief Valve Drain Tubes Table VIII ASME A Water Closet Personal Hygiene Devices Table VI, ASME A (R2010) ASME A (R2010) ASME A M (R2012) ASME A (R2010) Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System Manually Operated, Quarter-Turn Shutoff Valves for Use in Plumbing Systems Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use Framing-Affixed Supports for Off-the Floor Water Closets with Concealed Tanks Table VIII Table VI, , Table VI, , National Standard Plumbing Code - Illustrated

3 ASME A (R2007) ASME A (R2012) Floor and Trench Drains Table V, 5.3.6, , Figure A, Roof, Deck, and Balcony Drains Table V, , , ASME A Sanitary Floor Sinks Table V, ASME A (R2012) ASME A (R2004) ASME A (R2012) Backwater Valves Table VIII, Grease Interceptors Table X, , , Grease Removal Devices Table X, , , ASME A FOG (Fats, Oils, and Greases) Disposal Systems Table X, ASME A Plumbing Supply Fittings Table VI, 7.6.2, 7.7.1, 7.8.3, , ASME A /CSA B125.1 Refer to ASME A or CSA B125.1 Table VI, 7.6.2, 7.7.1, 7.8.3, , ASME A Plumbing Waste Fittings Table VI, 3.2.1, ASME A /CSA B125.2 Refer to ASME A or CSA B125.2 Table VI, 3.2.1, ASME A (R2012) Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings Table IX ASME A Flexible Water Connectors Table VI, ASME A /CSA B125.6 Refer to ASME A or CSA B125.6 Table VI, ASME A ASME A Protectors/Insulators for Exposed Wastes and Supplies on Accessible Fixtures Enameled Cast Iron and Enameled Steel Plumbing Fixtures Table VI, 7.2 Table V, 7.6.1, 7.8.1, ASME A /CSA B45.2 Refer to ASME A or CSA B45.2 Table V, 7.6.1, 7.8.1, ASME A Ceramic Plumbing Fixtures Table V, 7.4.1, 7.4.2, 7.5.1, 7.5.2, 7.6.1, 7.7.1, ASME A /CSA B45.1 Refer to ASME A or CSA B45.1 Table V, 7.4.1, 7.4.2, 7.5.1, 7.5.2, 7.6.1, 7.7.1, ASME A (R2013) Stainless Steel Plumbing Fixtures Table V, 7.6.1, ASME A /CSA B45.4 Refer to ASME A or CSA B45.4 Table V, 7.6.1, ASME A w/update 1 Flush Valves and Spuds for Water Closets, Urinals, and Tanks Table VI ASME A Hydromassage Bathtub Systems Table V, National Standard Plumbing Code - Illustrated 373

4 ASME A /CSA B45.10 Refer to ASME A or CSA B45.10 Table V, ASME A (R2008) ASME A (R2011) ASME A Dual Flush Devices for Water Closets Wall Mounted, Pedestal Mounted, Adjustable, Elevating, Tilting, and Pivoting Lavatory, Sink, and Shampoo Bowl Carrier Systems and Drain Waste Systems Six Liter Water Closets Equipped with a Dual Flushing Device Table VI Table VI, , 7.2 Table V ASME A Bathtubs/Whirlpool Bathtubs with Pressure Sealed Doors Table V, ASME A ASME A (R2011) ASME A M (R2012) ASME A w/updates 1 & 2 Manufactured Safety Vacuum Release Systems (SVRS) for Residential and Commercial Swimming Pool, Spa, Hot Tub, and Wading Pool Suction Systems Table VI Vitreous China Non-water Urinals Table V, Cleanouts Performance Requirements for Automatic Compensating Valves for Individual Shower and Tub/Shower Combinations ASME A /ASSE 1016/ Refer to ASME A , ASSE 1016, or CSA CSA B B Table VIII Table VI, Table VIII, Table VI, Table VIII, ASME B Pipe Threads, General Purpose (Inch), ASME B Malleable Iron Threaded Fittings: Classes 150 and 300 Table I, Table 3.4 ASME B Gray Iron Threaded Fittings: Classes 125 and 250 Table I, Table 3.4 ASME B Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard Table I, Table 3.4 ASME B Cast Iron Threaded Drainage Fittings Table I, Table 3.5, Table 3.6, Table 3.7 ASME B ASME B Ferrous Pipe Plugs, Bushings, and Locknuts with Pipe Threads Cast Copper Alloy Threaded Fittings: Classes 125 and 250 Table I Table II, Table 3.4 ASME B Cast Copper Alloy Solder Joint Pressure Fittings Table II, Table 3.4, 4.2.4, 4.2.6, ASME B Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings Table II, Table 3.4, 4.2.4, 4.2.6, , ASME B Cast Copper Alloy Solder Joint Drainage Fittings: DWV Table II, Table 3.5, Table 3.6, Table 3.7, ASME B Cast Copper Alloy Pipe Flanges and Flanged Fittings, Classes 150, 300, 400, 600, 800, 1500, and 2500 Table II, Table 3.4, ASME B Cast Copper Alloy Fittings for Flared Copper Tubes Table II, Table 3.4, National Standard Plumbing Code - Illustrated

5 ASME B ASME B Wrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings - DWV Wrought Copper and Copper Alloy Braze-Joint Pressure Fittings Table II, Table 3.5, Table 3.6, Table 3.7, Table II, Table 3.4, 4.2.4, ASME B Copper and Copper Alloy Press-Connect Pressure Fittings Table II, Table 3.4 ASSE ASSE ASSE ASSE ASSE Performance Requirements for Atmospheric Type Vacuum Breakers Performance Requirements for Anti-Siphon Fill Valves for Water Closet Tanks Performance Requirements for Water Pressure Reducing Valves for Domestic Water Distribution Systems Backflow Prevention Requirements for Commercial Dishwashing Machines Performance Requirements for Plumbing Aspects of Residential Food Waste Disposer Units Table IX, 7.8.4, , Table VI, Table VIII, Table IX, Table VII, ASSE Performance Requirements for Water Hammer Arresters Table VIII, ASSE ASSE ASSE ASSE ASSE ASSE Performance Requirements for Hose Connection Vacuum Breakers Performance Requirements for Backflow Preventer with Intermediate Atmospheric Vent Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Fire Protection Principle Backflow Preventers Performance Requirements for Backflow Prevention Devices for Hand-Held Showers Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies Performance Requirements for Automatic Compensating Valves for Individual Shower and Tub/Shower Combinations ASSE 1016/ASME A / Refer to ASSE 1016, ASME A , or CSA CSA B B ASSE Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems ASSE Performance Requirements for Trap Seal Primer Valves - Potable Water Supplied ASSE ASSE ASSE Performance Requirements for Wall Hydrants with Backflow Protection and Freeze Resistance Performance Requirements for Pressure Vacuum Breaker Assembly Performance Requirements for Drain Air Gaps for Domestic Dishwasher Applications Table IX, , , , Table IX, , Table VI, Table VIII, Table VI, Table VIII, Table VIII, , Table VIII, 5.3.6, Table IX, , Figure G, , Table IX 2015 National Standard Plumbing Code - Illustrated 375

6 ASSE ASSE ASSE ASSE (R2011) ASSE ASSE ASSE ASSE ASSE ASSE ASSE ASSE ASSE ASSE ASSE Performance Requirements for Backflow Preventer for Beverage Dispensing Equipment Performance Requirements for Hot Water Dispensers Household Storage Type - Electrical Performance Requirements for Dual Check Backflow Preventers Table VII , Performance Requirements for Dual Check Valve Type Table IX, Backflow Preventers for Carbonated Beverage Dispensers - Post Mix Type Performance Requirements for Laboratory Faucet Backflow Preventers Performance Requirements for Pressurized Flushing Devices (Flushometers) for Plumbing Fixtures Performance Requirements for Trap Seal Primer Devices - Drainage Types and Electronic Design Types Table VI, , Table VIII, 5.3.6, Performance Requirements for Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies , Performance Requirements for Double Check Detector Fire Protection Backflow Prevention Assemblies Performance Requirements for Hose Connection Backflow Preventers Performance Requirements for Dual Check Backflow Preventer Wall Hydrants - Freeze Resistant Type Performance Requirements for Chemical Dispensing Systems Performance Requirements for Spill Resistant Vacuum Breakers Performance Requirements for Freeze Resistant Sanitary Yard Hydrants with Backflow Protection Performance Requirements for Outdoor Enclosures for Fluid Carrying Components , Table IX, Table IX, Table IX, , Figure G, , Table IX, Table IX, ASSE Performance Requirements for Push-Fit Fittings Table II,, ASSE ASSE ASSE ASSE ASSE Performance Requirements for Temperature Actuated Flow Reduction (TAFR) Valves for Individual Fixture Fittings Performance Requirements for Automatic Temperature Control Mixing Valves Performance Requirements for Water Temperature Limiting Devices Performance Requirements for Temperature Actuated Mixing Valves for Plumbed Emergency Equipment Performance Requirements for Barrier Type Floor Drain Trap Seal Protection Devices Table VI, Table VIII, Table VIII, Table VIII, 7.24 Table VIII, 5.3.6, National Standard Plumbing Code - Illustrated

7 ASSE Performance Requirements for Dielectric Pipe Unions, ASSE ASTM A Professional Qualification Standard for Medical Gas Systems Personnel Standard Specification for Pipe, Steel, Black and Hot- Dipped, Zinc Coated, Welded and Seamless Table I, Table 3.4, Table 3.5, Table 3.6, Table 3.7, ASTM A a Standard Specification for Cast Iron Soil Pipe and Fittings Table I, Table 3.5, Table 3.6, Table 3.7 ASTM A (R2008)e1 Specifications for Ductile-Iron Pressure Pipe Table I, Table 3.4, ASTM A Standard Specification for Ductile Iron Culvert Pipe Table I, Table 3.5, Table 3.7 ASTM A ASTM A a ASTM A Standard Specification for Ductile Iron Gravity Sewer Pipe Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications Standard Specification for Cast Iron Couplings for Joining Hubless Cast Iron Soil Pipe and Fittings Table I, Table 3.5, Table 3.7 Table I, Table 3.5, Table 3.6, Table 3.7, ASTM B (R2009) Standard Specification for Refined Lead ASTM B Standard Specification for Solder Metal, 4.2.4, ASTM B Standard Specification for Red Brass Pipe, Standard Sizes Table II, Table 3.4 ASTM B Standard Specification for Seamless Copper Water Tube Table II, Table 3.4, Table 3.5, Table 3.6, Table 3.7, 4.2.6, , ASTM B Standard Specification for Threadless Copper Pipe, Standard Sizes Table II ASTM B Standard Specification for Copper Drainage Tube (DWV) Table II, Table 3.5, Table 3.6, Table 3.7 ASTM B ASTM B (R2010) ASTM C (R2009) ASTM C a ASTM C ASTM C Standard Specification for Liquid and Paste Fluxes for Copper and Copper Alloy Tube Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings Standard Specification for Clay Drain Tile and Perforated Clay Drain Tile, 4.2.4, Table XI, 4.2.4, Table 3.8 Standard Practice for Installing Vitrified Clay Pipe Lines Table XI Standard Specification for Non-reinforced Concrete Sewer, Storm Drain, and Culvert Pipe Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe Table 3.5, Table 3.7 Table 3.5, Table 3.7 ASTM C Standard Specification for Concrete Drain Tile Table 3.8 ASTM C (R2013) Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings 2015 National Standard Plumbing Code - Illustrated 377

8 ASTM C Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets ASTM C (R2009) Standard Specification for Perforated Concrete Pipe Table 3.8 ASTM C ASTM C ASTM C e1 ASTM C ASTM C ASTM C (R2013) ASTM C Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings Standard Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated Standard Specification for Flexible Transition Couplings for Underground Piping Systems Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings Standard Specification for Shielded Transition Couplings for Use With Dissimilar DWV Pipe and Fittings Above Ground Standard Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use Standard Specification for Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings ASTM D (R2010) Standard Specification for Rubber Sheet Gaskets ASTM D Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 ASTM D (R2011) Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings ASTM D a ASTM D ASTM D ASTM D ASTM D ASTM D a ASTM D Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications Table 3.5, Table 3.6, Table 3.7, Table 3.8, , 4.3.8, 4.3.8, 4.3.8, 4.3.8, Table 3.4, Table 3.4.2, Table 3.4, Table Table 3.4, Table , Table XI Standard Specification for Threaded Poly(Vinyl Chloride) Table 3.4 (PVC) Plastic Pipe Fittings, Schedule 80 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems ASTM D (R2008) Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe Table 3.4, Table 3.5, Table 3.6, Table 3.7 Table 3.4 Table National Standard Plumbing Code - Illustrated

9 ASTM D ASTM D Standard Specification for Acrylonitrile-Butadiene- Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings ASTM D a (R2009) Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement ASTM D (R2009) Standard Specification for Acrylonitrile-Butadiene- Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping ASTM D e2 ASTM D ASTM D a ASTM D ASTM D be1 Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings Standard Specification for Polyethylene (PE) Plastic Tubing Standard Practice for Underground Installation of Thermoplastic Pressure Piping Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems ASTM D (R2008) Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings ASTM D (R2010) Standard Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings ASTM D ASTM D ASTM D Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter ASTM D (R2009) Standard Specification for Solvent Cements for Styrene- Rubber (SR) Plastic Pipe and Fittings Table 3.5, Table 3.6, Table 3.7 Table 3.5, Table 3.6, Table 3.7 Table 3.5, Table 3.7 Table 3.4 Table 3.8 Table 3.4, Table , Table XI Table 3.4.3, Table 3.8 Table XI Table 3.5, Table 3.6, Table 3.7 Table 3.5, Table ASTM D (R2011) Standard Specification for Solvent Cements for Transition, Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components ASTM D (R2011) Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals ASTM D (R2013) Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals ASTM D e1 Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing, Table 3.4, Table 3.4, National Standard Plumbing Code - Illustrated 379

10 ASTM D ASTM D ASTM D ASTM D ASTM D ASTM D ASTM F (R2012) ASTM F ASTM F ASTM F ASTM F ASTM F ASTM F e1 ASTM F e1 ASTM F ASTM F (R2008) ASTM F ASTM F e1 Standard Specification for "Fiberglass" (Glass-Fiber- Reinforced Thermosetting-Resin) Sewer Pipe Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fitting Patterns Standard Specification for "Fiberglass" (Glass-Fiber- Reinforced Thermosetting-Resin) Pressure Pipe Standard Specification for "Fiberglass" (Glass-Fiber- Reinforced Thermosetting-Resin) Pipe Fittings for Non- Pressure Applications Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane Standard Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings Standard Specification for Corrugated Polyethylene (PE) Pipe and Fittings Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40 Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR) Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe Standard Practice for Installation of Thermoplastic Pipe and Corrugated Pipe in Septic Tank Leach Fields Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings Standard Specification for Acrylonitrile-Butadiene- Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core Table 3.5, Table 3.7 Table III Table 3.4 Table 3.5, Table 3.7 Table X Table X Table XI Table , Table VI Table 3.4 Table 3.4 Table 3.4 Table 3.4.3, Table 3.4.3, Table XI Table 3.5, Table 3.6, Table National Standard Plumbing Code - Illustrated

11 ASTM F ASTM F ASTM F ASTM F a ASTM F a ASTM F ASTM F ASTM F ASTM F Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields Standard Specification for Crosslinked Polyethylene (PEX) Tubing Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX- AL-PEX) Pressure Pipe Standard Specification for Polyethylene/Aluminum/ Polyethylene (PE-AL-PE) Composite Pressure Pipe ASTM F a (R2011) Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings ASTM F Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings ASTM F (R2013) Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications ASTM F (2012)e1 Standard Specification for Taper Pipe Threads 60º for Thermoplastic Pipe and Fittings ASTM F (R2011) Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content ASTM F a Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing ASTM F Standard Specification for Mechanical Cold Expansion Insert Fitting With Compression Sleeve for Cross-linked Polyethylene (PEX) Tubing Table 3.5, Table 3.7, , Table III Table Table Table 3.5, Table 3.6, Table 3.7, Table 3.4 Table Table Table XI Table 3.5, Table Table 3.5, Table 3.6, Table 3.7 Table 3.4 Table National Standard Plumbing Code - Illustrated 381

12 ASTM F ASTM F ASTM F Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing Standard Specification for Metal Mechanical Cold Flare Compression Fittings with Disc Spring for Crosslinked Polyethylene (PEX) Tubing Table 3.5, Table 3.6, Table 3.7 Table 3.4 Table 3.4 ASTM F e1 Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly(Vinyl Chloride) Table (PVC) or Chlorinated Poly(Vinyl Chloride) (CPVC) Systems ASTM F Standard Specification for Metal Insert Fittings for Table 3.4 Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe ASTM F (R2013) Standard Specification for Non-Reinforced Extruded Tee Connections for Piping Applications, ASTM F Standard Specification for Cold-Expansion Fittings with Table 3.4 Metal Compression Sleeves for Crosslinked Polyethylene (PEX) Pipe ASTM F Standard Specification for Stainless Steel Clamps for Table 3.4 Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert and Plastic Insert Fittings ASTM F Standard Specification for Plastic Insert Fittings Utilizing Table 3.4 a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing ASTM F Standard Specification for Flexible Pre-Insulated Piping Table 3.4 ASTM F Standard Specification for Crosslinked Polyethylene/ Table Aluminum/Crosslinked Polyethylene Tubing OD 3.4, Table 3.4.2, Table Controlled SDR ASTM F Standard Specification for Pressure-rated Polypropylene Table (PP) Piping Systems 3.4, ASTM F Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing Table 3.4 ASTM F Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Table 3.5, Table 3.6 Drainage Systems ASTM F Standard Practice for Heat Fusion Joining of Polyethylene Table XI, , Pipe and Fittings ASTM F Standard Specification for Plastic Insert Fittings for SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing Table National Standard Plumbing Code - Illustrated

13 ASTM F ASTM F ASTM F AWS A , w/amendment 1 AWWA C104/A Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold Water Tubing and Distribution Systems Standard Specification for Metric and Inch-Sized Crosslinked Polyethylene (PEX) Pipe Standard Specification for Chlorinated Poly(Vinyl Chloride)/Aluminum/Chlorinated Poly(Vinyl Chloride) (CPVC-AL-CPVC) Composite Pressure Tubing Specification for Filler Metals for Brazing and Braze Welding Cement Mortar Lining for Ductile Iron Pipe and Fittings for Water Table Table 3.4 Table Table I AWWA C110/A Ductile-Iron and Gray-Iron Fittings Table I, Table 3.4, Table 3.5, Table 3.7 AWWA C111/A Rubber-Gasketed Joints for Ductile-Iron Pressure Pipe and Fittings AWWA C151/A Ductile-Iron Pipe, Centrifugally Cast Table I, Table 3.4 AWWA C153/A Ductile Iron Compact Fittings Table I, Table 3.4, Table 3.5, Table 3.7 AWWA C Metal-Seated Gate Valves for Water Supply Service Table VIII AWWA C Installation of Ductile-Iron Water Mains and Their Appurtenances Table XI AWWA C Grooved and Shouldered Joints, Table 3.4 AWWA C Underground Service Line Valves and Fittings Table 3.4 AWWA C AWWA C AWWA C AWWA C Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 In. Through 12 In. for Water Transmission and Distribution Polyethylene (PE) Pressure Pipe and Tubing, 1/2 In. Through 3 In. for Water Service Polyethylene-Aluminum-Polyethylene Crosslinked Polyethylene Composite Pressure Pipes, 1/2 In. Through 2 In. for Water Service Cross-Linked Polyethylene (PEX) Pressure Pipe, 1/2 In. Through 3 In. for Water Service Table 3.4, Table Table 3.4, Table Table 3.4, Table AWWA C Fiberglass Pressure Pipe Table 3.4 CISPI CISPI CSA Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications Specification for Coupling for Use in Connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications Gas Water Heaters - Volume I, Storage Water Heaters with Input Ratings of 75,000 Btu Per Hour or Less Table I, Table 3.5, Table 3.6, Table 3.7, Table VII, National Standard Plumbing Code - Illustrated 383

14 CSA Gas Water Heaters - Volume III, Storage Water Heaters, With Input Ratings Above 75,000 Btu Per Hour, Circulating and Instantaneous Table VII, CSA M1999 (R2008) Relief Valves for Hot Water Supply Systems Table VIII, , Figure CSA B Ceramic Plumbing Fixtures Table V, 7.4.1, 7.4.2, 7.5.1, 7.5.2, 7.6.1, 7.7.1, CSA B Enameled Cast Iron and Enameled Steel Plumbing Fixtures Table V, 7.6.1, 7.8.1, CSA B (R2013) Stainless Steel Plumbing Fixtures Table V, 7.6.1, CSA B w/update 1 Plastic Plumbing Fixtures Table V, 7.4.1, 7.4.2, 7.5.1, 7.5.2, 7.6.1, 7.8.1, , CSA B45.5/IAPMO Z124 Refer to CSA B45.5 or IAPMO Z124 Table V, 7.4.1, 7.4.2, 7.5.1, 7.5.2, 7.6.1, 7.8.1, , CSA B Plumbing Fixtures with Pumped Waste and Macerating Plumbing Systems Table X, 7.4.8, CSA B Hydromassage Bathtub Systems Table V, CSA B w/update 1 Flush Valves and Spuds for Water Closets, Urinals, and Tanks CSA B Dual Check Valve (DuC) Backflow Preventers Table VI CSA B Plumbing Supply Fittings Table VI, 7.6.2, 7.7.1, 7.8.3, , CSA B Plumbing Waste Fittings Table VI, 3.2.1, CSA B Plumbing Fittings Table VI, Table VIII, , , CSA B Flexible Water Connectors Table VI, CSA B , w/update 1 CSA B CSA B CSA B CSA B w/updates 1 & 2 Performance Requirements for Automatic Compensating Valves for Individual Shower and Tub/Shower Combinations Chlorinated Polyvinylchloride (CPVC) Pipe, Tubing, and Fittings for Hot- and Cold-Water Distribution Systems Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure-Pipe Systems Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Composite Pressure-Pipe Systems Table VI, Table VIII, Table 3.4 Table III Table III Acrylonitrile-Butadiene-Styrene (ABS) Drain, Waste, and Vent Pipe and Fittings Table VIII National Standard Plumbing Code - Illustrated

15 CSA B w/updates 1 & 2 Polyvinylchloride (PVC) and Chlorinated Polyvinylchloride (CPVC) Drain, Waste, and Vent Pipe and Pipe Fittings Table VIII CSA B (R2012) Drinking Water Treatment Systems Table VII, CSA B FM IAPMO Z w/update 1 Mechanical Couplings for Drain, Waste, and Vent Pipe and Sewer, Couplings Used in Hubless Cast Iron Systems for Drain,, Waste or Vent, Sewer, Rainwater or Storm Drain Systems Above and Below Ground Industrial/Commercial and Residential Plastic Plumbing Fixtures Table V, 7.4.1, 7.4.2, 7.5.1, 7.5.2, 7.6.1, 7.8.1, , IAPMO/ANSI Z e1 Plastic Toilet Seats Table VI, IAPMO/ANSI Z Prefabricated Plastic Spa Shells Table V IAPMO/ANSI Z e1 Plastic Liners for Bathtubs and Shower Receptors Table VI IAPMO/ANSI Z Prefabricated Gravity Grease Interceptors Table X, IAPMO/ANSI Z Pre-Pressurized Water Expansion Tanks Table VIII MSS SP Pipe Hangers and Supports - Materials, Design, Manufacture, Selection, Application, and Installation Table X, 8.10 MSS SP Gray Iron Gate Valves, Flanged and Threaded Ends Table VIII MSS SP Gray Iron Swing Check Valves, Flanged and Threaded Ends Table VIII MSS SP Bronze Gate, Globe, Angle and Check Valves Table VIII MSS SP Ball Valves Threaded, Socket-Welding, Solder Joint, Grooved and Flared Ends NFPA Standard for the Installation of Sprinkler Systems NFPA 13D NFPA 13R Standard for the Installation of Sprinkler Systems in Oneand Two-Family Dwellings and Manufactured Homes Standard for the Installation of Sprinkler Systems in Low Rise Residential Occupancies Table VIII 2.28, , , , , , , NFPA Health Care Facilities Code , , , , NSF Commercial Warewashing Equipment Table VII, NSF Plastics Piping System Components and Related Materials 3.1.3, NSF Drinking Water Treatment Units - Aesthetic Effects Table VII, NSF Residential Cation Exchange Water Softeners Table VII, NSF Drinking Water Treatment Units - Health Effects Table VII, NSF Ultraviolet Microbiological Water Treatment Systems Table VII, NSF Reverse Osmosis Drinking Water Treatment Systems Table VII, NSF Drinking Water System Components - Health Effects 1.2 Lead Content, 3.1.5, 3.4.6, 3.4.7, 4.2.6, NSF Drinking Water System Components - Lead Content 3.4.7, National Standard Plumbing Code - Illustrated 385

16 PDI G Testing and Rating Procedure for Hydro Mechanical Grease Interceptors Table X, , , 6.2.2, PDI WH Water Hammer Arrestors Table VIII, , Figure UL th Edition, 2004 Standard for Household Electric Storage Tank Water Heaters Table VII, UL 399-7th Edition, 2008 Standard for Drinking Water Coolers Table V, UL 430-7th Edition, 2009 Standard for Waste Disposers Table VII, UL th Edition, 2005 Standard for Electric Heating Appliances Table VII, UL 732-5th edition, 1995 Standard for Oil-Fired Storage Tank Water Heaters Table VII, UL 749-9th Edition, 2013 Household Dishwashers Table VII, UL 921-6th Edition, 2006 Commercial Electric Dishwashers Table VII, UL th Edition, 2003 UL th Edition, 2004 Standard for Electric Commercial Clothes-Washing Equipment Standard for Electric Booster and Commercial Storage Tank Water Heaters Table VII, Table VII, UL nd Edition, 1997 Electrical Clothes Washing Machines and Extractors Table VII, National Standard Plumbing Code - Illustrated