Dimmer / Fan Controller Installation Instructions

Transcription

1 Dimmer / Fan Controller Installation Instructions US P P H US US H U S H O N N F O F FF

2 Table of Contents Section... Page 1.0 Product Range Description Features Soft Start Operation Unloaded LV Iron-Core Transformer Cut-Out Overtemperature Compensation Compatible Loads Unit Operation Installation Instructions Wiring Details Minimum Brightness Settings Low Voltage Lighting Transformers Multi-Gang Derating Ceiling Fans Product Specifications...6 Copyright Notice Copyright 2002 Gerard Industries Pty Ltd. All rights reserved. Trademarks Clipsal is a registered trademark of Gerard Industries Pty Ltd. All other logos and trademarks are the property of their respective owners. Disclaimer Gerard Industries Pty Ltd reserves the right to change specifications or designs described in this manual without notice and without obligation. Copyright 2002 Gerard Industries Pty Ltd Page 2

3 1.0 Product Range 31E1000L 2031E1000L Dimmer, leading edge, 1000W, 240V, 50Hz, (Standard) Dimmer, leading edge, 1000W, 240V, 50Hz, (2000 Series) 2.0 Description The Clipsal Dimmer/Fan Controller, rated at 1000W (4A), gives full control of lighting and fans in domestic and commercial applications. The Dimmer complies with the Australian Standards (AS/NZS1044, AS/NZS4051) for EMC. An integral push-on/push-off switch is incorporated into the knob, which also controls the lamp brightness or fan speed. 3.0 Features 3.1 Soft Start Operation The dimmers incorporate a soft start feature providing a noticeably smooth lamp illumination at turn on. This feature also minimises lamp filament start up stress, which may increase lamp lifetime. 3.2 Unloaded LV Iron-Core Transformer Cut-Out The dimmers incorporate a safety cut-out, reducing the possibility of low voltage transformers overheating when a load (lamp) is not present (or has blown). Under these circumstances normal dimmer operation can be restored by switching the dimmer off before replacing the faulty lamp. 3.3 Overtemperature Compensation The dimmers incorporate thermal overload compensation, which automatically reduces lamp brightness should the dimmer be inadvertently overloaded. 4.0 Compatible Loads Incandescent or halogen 240V lamps, Low voltage lighting with iron-core transformers, Exhaust fans ie shaded pole induction motors, Ceiling fans ie split-phase induction motors, Any combination of above specified load type Not recommended for low voltage lighting with electronic transformers, unless used in conjunction with inductor unit Cat. No. 32EIND (limited to 2A max. load). Not suitable for fluorescent lighting. 5.0 Unit Operation The Dimmer/Controller is switched on or off by pressing the control/on/off knob. Brightness (or fan speed) is adjusted by rotating the control knob: clockwise increases brightness (or fan speed), anti-clock wise decreases brightness (or fan speed). Pressing the on/off switch does not alter the level setting. Copyright 2002 Gerard Industries Pty Ltd Page 3

4 6.0 Installation Instructions 6.1 Wiring Details Connect the 31E1000L in accordance with the wiring diagrams. (The wiring diagrams equally apply for fan applications) 6.2 Minimum Brightness Settings The minimum brightness level has been factory set to suit incandescent or ironcore based low voltage lamp applications. The minimum setting trimming potentiometer, which is accessible through the side of the case can be adjusted, if required, using the small plastic screwdriver supplied. When the is used to control fan loads it will typically be necessary to advance the minimum setting towards the fully clockwise position. This setting allows smooth control of fan rotational speed over the full control range of the control knob, and prevents the motor stalling at low speed settings. 6.3 Low Voltage Lighting Transformers Typically, dimmer load ratings must be derated in order to account for low voltage lighting transformer inefficiency. The 31E1000L dimmer does not require such derating, and is capable of driving the full 1000W of iron-core based low voltage lighting lamps (eg 20 x 50W lamps). 6.4 Multi-Gang Derating For applications, where 31E1000L Dimmers are multi-ganged or mounted in close proximity to each other, the maximum load rating is to be derated to 750W (3A). The overtemperature compensation feature may reduce the maximum attainable brightness if dimmers are too closely spaced. 6.5 Ceiling Fans Some ceiling fan models produce audible humming noise when used in conjunction with phase-control fan speed controllers. Careful selection of fan make and model will minimise this effect. Copyright 2002 Gerard Industries Pty Ltd Page 4

5 ONE WAY SWITCHING LOAD 1-WAY LINE 2-WAY LOOP INCANDESCENT LOAD NEUTRAL LINE TWO WAY SWITCHING LOAD 1-WAY LINE 2-WAY LOOP INCANDESCENT LOAD 1-WAY 2-WAY ADDITIONAL SWITCH NEUTRAL LINE Copyright 2002 Gerard Industries Pty Ltd Page 5

6 7.0 Product Specifications Electrical Specifications Parameter Nominal Operating Voltage Nominal Operating Frequency Value V a.c. 50 Hz Maximum Load* 1000W incandescent lamps 1000W iron-core based LV lighting 1000VA fan motors * Derate to 750W for multi-gang applications Minimum Load 20W incandescent lamps 20W iron-core based LV lighting 40W fan motors (4A) (4A) (4A) (3A) (0.1A) (0.1A) (0.2A) Dimming Technique Compatible Loads Leading-Edge Phase Control Incandescent lighting Halogen 240V lamps Low voltage lighting with iron-core transformers M Operating Temperature Range 0 to 40 C Exhaust fans (shaded pole induction motors) Ceiling fans (split-phase induction motors) Operating Humidity Range Mounting Centres Shipping weight EMC Emission Compliance 10 to 90% R.H. 84mm 180g AS/NZS1044, AS/NZS4051 Copyright 2002 Gerard Industries Pty Ltd Page 6

7 Mechanical Specifications Dimensions are in millimetres. No user serviceable parts inside. Copyright 2002 Gerard Industries Pty Ltd Page 7

8 WARRANTY STATEMENT 1. The benefits conferred herein are in addition to, and in no way shall be deemed to derogate; either expressly or by implication, any or all other rights and remedies in respect to the Clipsal Product, which the consumer has under the Commonwealth Trade Practices Act or any other similar State or Territory Laws. 2. The warrantor is Gerard Industries Pty Ltd of 12 Park Terrace Bowden, South Australia Telephone (08) With registered offices in all Australian States. 3. This Clipsal Product is guaranteed against faulty workmanship and materials for a period of two (2) years from the date of installation. 4. Gerard Industries Pty Ltd reserves the right, at its discretion, to either repair free of parts and labour charges, replace or offer refund in respect to any article found to be faulty due to materials, parts or workmanship. 5. This warranty is expressly subject to the Clipsal Product being installed, wired, tested, operated and used in accordance with the manufacturer s instructions. 6. All costs of a claim shall be met by Gerard Industries Pty Ltd, however should the product that is the subject of the claim be found to be in good working order all such costs shall be met by the claimant. 7. When making a claim the consumer shall forward the Clipsal Product to the nearest office of Gerard Industries Pty Ltd with adequate particulars of the defect within 28 days of the fault occurring. The product should be returned securely packed, complete with details of the date and place of purchase, description of load, and circumstances of malfunction. Australian Offices South Australia 12 Park Terrace, Bowden, (08) New South Wales 122 Canterbury Road, Padstow, (02) Victoria Queens Parade, North Fitzroy, (03) Queensland Brisbane Nudgee Road, Nudgee, (07) Western Australia 23 Truganina Road, Malaga, (08) Tasmania Hobart - 55 Lampton Avenue, Derwent Park, (03) Northern Territory 16 Albatross Street, Winnellie (08) Products of Gerard Industries Pty Ltd ABN Head Office 12 Park Terrace, Bowden South Australia 5007 Telephone (08) Facsimile (08) Internet cis@clipsal.com.au /02