Installation Instructions

Transcription

1 Installation Instructions Quick Reference Table of ontents: Pages Product dimensions utout dimensions Before you start Electrical requirements Installation steps If you need assistance: heck your Use and are Guide for a toll-free number to call or call the dealer from whom you purchased this appliance. The dealer is listed in the Yellow Pages of your phone directory under ppliances Household Major Service and Repair. all when you: Have questions about built-in installation or operation. Need to obtain the name and number of an authorized service company. 27" and 30" Electric Built-in Microwave/ Oven ombination When you call, you will need: The built-in model number. The built-in serial number. Both numbers are listed on the model/serial rating plate, located on the microwave frame. IMPORTNT: Read and save these instructions. Part No IMPORTNT: Installer: Leave Installation Instructions with the homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector's use.

2 Product dimensions 4" 23" max. depth 25-3/8 utout dimensions 4-/4" -/2" min. to top of 27 27" min. 25-/2" 27" 23-/4" min. depth 23" depth 26-3/4" overall abinet side view 42-7/6" overall " top of to upper 9-/4" to floor front 4" 23" max. depth 4-/4" -/2" min. to top of Tool needed: Phillips screwdriver /8" 30" min. 28-/2" 30" 29-3/4" overall 42-7/6" overall " top of to bottom of upper 9-/4" bottom of to floor abinet filler kits are available from your dealer. Use a matching color kit if is smaller than your opening. 27" filler is 7-3/6" Black White lmond " filler is 4-3/6" Black White lmond Parts supplied: 4 screws Before you start... Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. lways read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. ll safety messages will follow the safety alert symbol and either the word DNGER or. These words mean: DNGER You can be killed or seriously injured if you don t immediately follow instructions. You can be killed or seriously injured if you don t follow instructions. ll safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. Important: Observe all governing codes and ordinances. Proper installation is your responsibility. Have a qualified technician install this. Oven location should be away from strong draft areas, such as windows, s and strong heating vents. abinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Recessed installation area must provide complete enclosure around the portion of the. Electrical ground is required. See Electrical requirements. Electrical supply junction box should be located 3 inches maximum below the support surface when is installed in a wall. utout for wiring should be in the right rear or left rear corner. For undercounter installation, it is recommended that the junction box be located in the adjacent right or left. If installing junction box on rear wall behind, junction box must be and located in the upper or lower right or left corner of. Oven support surface MUST be solid, level and flush with. Excessive Microwave Energy Exposure Do Not attempt to operate the microwave with the open. Do Not tamper with or defeat the safety interlocks. Do Not place objects between the microwave front face and. Do Not allow soil or cleaner residue to accumulate on sealing surface of the microwave. Do Not operate the microwave if damaged. Do Not operate the microwave if: is bent. hinges and latches are broken or loose. seals, sealing surfaces or glass are broken. The microwave must close properly to provide safe operation. Have a qualified repair person adjust, repair and check microwave for microwave leakage after a repair is made. Do Not use microwave for commercial purposes. The microwave in this unit is designed for household use only. Failure to follow these instructions could result in exposure to excessive microwave energy. It is the customer s responsibility: To contact a qualified electrical installer. To assure that the electrical installation is adequate and in conformance with National Electrical ode, NSI/NFP 70 latest edition*, and all local codes and ordinances. opies of the standards listed may be obtained from: * National Fire Protection ssociation Batterymarch Park Quincy, Massachusetts Page

3 Electrical requirements If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path and wire gauge are in accordance with local codes. Do Not ground to a gas pipe. heck with a qualified electrician if you are not sure is properly grounded. Do Not have a fuse in the neutral or grounding circuit. This must be connected to a grounding metal, permanent wiring system. Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial rating plate. (The model/serial rating plate is located on the or on the frame.) Models rated from 7.3 to 9.6 kw at 240 volts (5.5 to 7.2 kw at 208 volts) require a separate 40-ampere circuit. Models rated at 7.2 kw and Installation Steps below at 240 volts (5.4 kw and below at 208 volts) require a separate 30-ampere circuit. time-delay fuse or circuit breaker is recommended. onnect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with grounding wire). Flexible armored appliance should be connected directly to junction box. Fuse both sides of the line. U.L.-listed conduit connector must be provided at the junction box. Do Not cut the conduit. Wire sizes and connections must conform with the rating of the appliance and to the requirements of the National Electrical ode, NSI/NFP 70 latest edition (*, See Page ) and all local codes and ordinances. If the house has aluminum wiring, follow the procedure below. a.) onnect the aluminum wiring to the copper wire using special connectors designed and Underwriters Laboratories-listed for joining copper to aluminum. Follow the electrical connector manufacturer s recommended procedure. b.) luminum/copper connection must conform with local codes and industry-accepted wiring practice. Preparation Grasp frame to lift. D heck and microwave operation. Excessive Weight Hazard Use two or more people to move and install. Failure to follow this instruction can result in back or other injury. Important: Use both hands to remove s. Do Not use handle or any portion of the front frame or trim for lifting. Before moving across floor, check that is on shipping base or slide onto cardboard or hardboard. Do Not remove shipping feet at the front lower corners of. B Remove side trim pieces. power supply cable Use screws to attach to. Reattach side trim pieces. shipping foot Remove racks. Remove trim screws. Remove. Do Not remove shipping feet.. Turn power supply off. Move close to final position. Remove and discard shipping materials, tape and protective film from the. Do Not remove shipping base or shipping feet at the front lower corners of. The shipping feet will protect the lower trim until is inserted into. Remove and set aside racks and other parts from inside. latch on the hinge in locked position free to open and close latch on the hinge in unlocked position ready for removal Remove trim screw. Pull trim out. Replace. Pull top of trim down. 2. ompletely open. In both back corners of the you will see latches in the locked position. Rotate both latches forward to the unlocked position. Grasp outside edges of with both hands. Begin closing, at the moment the stops closing, lift and pull toward you. Set aside on a protective surface. 3. Remove trim screws attaching right and left side trim to. Grasp the bottom end of trim and pull away from. Slide top end of trim downward to remove trim from. Take care not to scratch other surfaces with ends of trim. Set trim and screws aside on protected surface. Page 2

4 B Electrical connection If your house has aluminum wiring, see Electrical requirements, Page 2. junction box red white wire power supply black junction box red power supply white Electrical Shock Hazard Turn power supply off before connecting. Use 8 gauge solid copper wire. Electrically ground range. Failure to follow these instructions can result in death, fire, or electrical shock. This is manufactured with white (neutral) power supply wire and a -connected bare grounding wire twisted together. 4. Feed cable through opening in the. Make electrical connection following the steps needed for your installation.. Disconnect the power supply. 2. Remove the junction box cover. 3. onnect cable to junction box through the U.L.-listed conduit connector. 4. onnect the two black together with twist-on connectors. 5. onnect the two red together with twist-on connectors. 6. omplete electrical connection according to local codes and ordinances. white and bare grounding cable factory crimped Figure If local codes PERMIT connecting -grounding conductor to neutral white wire in junction box: 7. onnect the factory-crimped bare and white cable to the neutral (white) wire in junction box. See Figure. 8. Replace junction box cover. bare grounding U.L.-listed conduit connector Figure 2 If local codes DO NOT PERMIT connecting -grounding conductor to neutral white wire in junction box: 7. Separate the factory-crimped bare and white cable. 8. onnect white cable wire to 9. onnect the bare grounding cable wire to a grounded wire in the junction box. See Figure Replace junction box cover. black U.L.-listed conduit connector If connecting to a four-wire electrical system: 7. Separate bare and white cable. 8. onnect white cable wire to 9. onnect the bare grounding cable wire to the green grounding wire in junction box. Do Not connect bare grounding wire to 0. Replace junction box cover. ttachment arefully push against seal area of front frame when pushing into. Do Not push against outside edges. 5. Lift into using the opening as an area to grip. shipping foot Push against seal area of front frame to push into until shipping feet almost contact. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping feet. Push completely into and center in. Slide top of trim up. 4 screws 6. Important: Securely fasten to using the screws provided (two screws for a single or four screws for a double ). Insert the screws through holes in mounting rails. Do Not overtighten screws. Push trim into place. Replace trim screw. 7. Slide top end of each trim upward onto side rails. Push each trim into place at trim. Use screws to attach each trim to. Take care not to scratch other surfaces with ends of trim. 8. Replace racks. 9. Reinstall the by inserting ends of hinges into hinge slots in the frame. Push hinges in as far as they will go. Open the (you will feel the drop into place) and rotate both hinge latches back to the locked position. lose and open the to check that the closes and opens completely. If does not close or open completely, repeat the removal step and reinstall as described above. D. heck the operation of your lower. Press the BROIL pad. BROIL will appear in the display. Press the STRT pad. Page 3 heck operation 0. Turn on power supply. The display panel will light up briefly. PF should appear in the temperature display. BKE BROIL LEN Make sure the is closed and the ON light is shown in the display area. fter 2 minutes, partially open. You should feel heat from the. Press the NEL pad. If your does not heat or an F appears in the display, contact your dealer or check the If you need service... section of this Installation Instructions. 2. heck the operation of the microwave. Fill a microwave-safe container with one cup of water and place container inside microwave. lose firmly. Set microwave cook time to 2:00 minutes. Press the STRT/ENTER pad. The interior microwave light should be on and the remaining cooking time should be displayed. When display reads :00, open microwave. The microwave should stop cooking. lose firmly. The interior microwave light should turn off. Press the STRT/ENTER pad. Microwave should begin cooking and the microwave interior light should be on. Let microwave complete cooking time. tone will sound four times at end of cooking time and microwave will shut off. Open microwave and carefully remove container. Water in container should be hot. To get the most efficient use from your new, read your Use and are Guide. Keep Installation Instructions and Guide close to for easy reference.

5 If does not operate: heck that circuit breaker is not tripped or house fuse blown. See Use and are Guide for troubleshooting list. If you need assistance: If you have questions about operating, cleaning or maintaining your : Refer to Use and are Guide. all the onsumer ssistance enter: heck your Use and are Guide for a toll-free number to call or call the dealer from whom you purchased this appliance. The dealer is listed in the Yellow Pages of your phone directory under ppliances Household Major Service and Repair. If you need service: Maintain the quality built into your built-in by calling an authorized service company. To obtain the name and number of an authorized service company: ontact the dealer from whom you purchased your built-in ; or Look in the Yellow Pages of your telephone directory under ppliances Household Major Service and Repair for an authorized service company; or all the onsumer ssistance enter. The tollfree number is listed in your Use and are Guide. When you call, you will need: The built-in model number. The built-in serial number. Both numbers are listed on the model/serial rating plate, located on the microwave frame. Part No Printed in U.S..