PARTS LIST MANUAL MODEL SS26-35K. Gasoline Powered 35 H.P. Kohler Command Pro Self-Propelled Concrete & Asphalt Saw SAW SET-UP OPTIONS

Transcription

1 REVISED STARTING SERIAL # PARTS LIST MANUAL MODEL SS26-35K Gasoline Powered 35 H.P. Kohler Command Pro Self-Propelled Concrete & Asphalt Saw SAW SET-UP OPTIONS SKU NUMBER BLADE GUARD SIZE BLADE SPEED INCH 900 RPM INCH 200 RPM INCH 200 RPM INCH 2750 RPM JWA 206 Page

2 READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT. Death or serious injury could occur if this machine is used improperly. SAFETY SAFETY MESSAGES MESSAGES Safety Instructions are proceeded by a graphic alert symbol of DANGER, WARNING, or CAUTION. Indicates an imminent hazard which, if not avoided, will result in death or serious injury. Indicates an imminent hazard which, if not avoided, can result in death or serious injury. Indicates hazards which, if not avoided, could result in serious injury and or damage to the equipment. GASOLINE/PROPANE POWERED EQUIPMENT Engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Gasoline is extremely flammable and poisonous. It should only be dispensed in well ventilated areas, and with a cool engine. Small gasoline engines produce high concentrations of carbon monoxide (CO) example: a 5 HP 4 cycle engine operation in an enclosed 00,000 cu. ft. area with only one change of air per hour is capable of providing deadly concentrations of CO in less than fifteen minutes. Five changes of air in the same area will produce noxious fumes in less than 30 minutes. Gasoline or propane powered equipment should not be used in enclosed or partially enclosed areas. Symptoms of CO poisoning include, headache, nausea, weakness, dizziness, visual problems and loss of consciousness. If symptoms occur - get into fresh air and seek medical attention immediately. ELECTRICAL POWERED EQUIPMENT Extreme care must be taken when operating electric models with water present: Ensure power cord is properly grounded, is attached to a Ground-Fault-Interrupter (GFI) outlet, and is undamaged. Check all electrical cables - be sure connections are tight and cable is continuous and in good condition. Be sure cable is correctly rated for both the operating current and voltage of this equipment. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with qualified electrician or service person if there is any doubt as to whether the outlet is properly grounded. Adhere to all local codes and ordinances. NOTE: In the event of a malfunction or breakdown, grounding provides a path of least resistance for the electric current to dissipate. The motor is equipped with a grounded plug and must be connected to an outlet that is properly installed and properly grounded. DO NOT modify the plug provided on the motor. If the plug does not fit the outlet have a qualified electrician install the proper receptacle. Switch motor OFF before disconnecting power. Do not disconnect power by pulling cord. To disconnect, grasp the plug, not the cord. Unplug power cord at the machine when not in use and before servicing. GENERAL INSTRUCTIONS Equipment should only be operated by trained personnel in good physical condition and mental health (not fatigued). The operator and maintenance personnel must be physically able to handle the bulk weight and power of this equipment. This is a one person tool. Maintain a safe operating distance to other personnel. It is the operators responsibility to keep other people (workers, pedestrians, bystanders, etc.) away during operation. Block off the work area in all directions with roping, safety netting, etc. for a safe distance. Failure to do so may result in others being injured by flying debris or exposing them to harmful dust and noise. This equipment is intended for commercial use only. For the operator s safety and the safety of others, always keep all guards in place during operation. Never let equipment run unattended. Personal Protection Equipment and proper safety attire must be worn when operating this machinery. The operator must wear approved safety equipment appropriate for the job such as hard hat and safety shoes when conditions require. Hearing protection MUST be used (operational noise levels of this equipment may exceed 85db). Eye protection MUST be worn at all times. Keep body parts and loose clothing away from moving parts. Failure to do so could result in dismemberment or death. Do not modify the machine. Stop motor/engine when adjusting or servicing this equipment. Maintain a safe operating distance from flammable materials. Sparks from the cutting-action of this machine can ignite flammable materials or vapors. DUST WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are: Lead from lead-based paints, and Crystalline silica from bricks and concrete and other masonry products. Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your risk: work in a well ventilated area, use a dust control system, such as an industrial-style vacuum, and wear approved personal safety equipment, such as a dust/particle respirator designed to filter out microscopic particles. 206 JWA Page 2

3 PARTS LIST MANUAL FOR MODEL SS26-35K Section TABLE OF CONTENTS Page Numbers Safety Messages & General Instructions How To Order Replacement Parts Illustration : Frame Grouping , 5 Illustration 2: Lift Grouping , 7 Illustration 3: Rear Axle Grouping , 9 Illustration 4: Transmission, Drive Lever & Linkage Grouping , Illustration 5: Clutch Lever & Linkage Grouping , 3 Illustration 6: Clutch Grouping , 5 Illustration 7: Arbor Grouping , 7 Illustration 8: Blade Guard Grouping , 9 Illustration 9: Water Pump Grouping , 2 Illustration 0: Instrument Panel Grouping Illustration : Blade Depth Gauge Grouping Illustration 2: Operating Controls Illustration 3: Guide Bar Assembly Illustration 4: Engine & Mount Grouping , 27 Illustration 5: Belt Drive Grouping , 29 Illustration 6: Fuel Tank Grouping , 3 Illustration 7: Oil Drain Grouping Illustration 8: Battery Grouping Wiring Diagram for SS26-35K Decals Sheets , 36, 37 This Page Left Blank Intentionally Notes Limited Equipment Warranty of Sale - Terms & Conditions HOW TO ORDER REPLACEMENT PARTS To insure product safety and reliability, always use genuine EDCO replacement parts when making repairs to the equipment. When calling for parts, specify the MODEL and SERIAL number of the machine, which can be found on the NAME PLATE. Keep that information in the space provided. In addition to this information, give part number, description, and quantity as listed on the parts list to your parts representative. Please note: Due to improvements and changes in the equipment, the illustrations shown may be different than the actual machine. FILL IN INFORMATION BELOW Date of Purchase Model # Serial # SKU # JWA 206 Page 3

4 ILLUSTRATION : FRAME GROUPING 206 JWA Page 4

5 PARTS LISTING - ILLUSTRATION : FRAME GROUPING 5070 MAIN FRAME, SS CONSOLE, SS-26 GAS SCREW, CAP 3/8-6 X WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC HANDLE BAR 36, SS GRIP, HAND MODEL AT PIN, DETENT RING 3/6 X -5/ KNOB, STAR CLAMPING 2 3/8-6 X STUD K BAIL, LIFTING 032 SCREW, CAP /2-20 X -/ WASHER, FLAT /2 SAE ZINC WASHER, LOCK /2 ZINC NUT, HEX /2-20 ZINC BRACE, LIFTING BAIL SCREW, CAP 5/6-8 X WASHER, FLAT 5/6 SAE ZINC WASHER, LOCK 5/6 ZINC NUT, HEX 5/6-8 ZINC BOLT, EYE SHOULDER 5/6-8 X -/ BUMPER, RUBBER OD X 3/6ID X 7/6H S WASHER, FENDER 3 /4ID X -/4OD S.S SCREW, MACHINE 0-32 X NUT, KEPS LOCK 0-32 ZINC MOUNT, TRANSMISSION, SS SCREW, CAP 3/8-24 X WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-24 ZINC GUIDE POINTER, REAR SCREW, CAP /4-20 X /2 ZINC K BELT COVER, SS26-35K SCREW, CAP 5/6-8 X 3/ WASHER, LOCK 5/6 ZINC WASHER, FLAT 5/6 SAE ZINC SCREW, CAP 3/8-6 X 3/ WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC COVER, ARBOR, SS SCREW, CAP 3/8-6 X 3/ WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC PIN, DETENT RING /4 X E.L GUARD, LOWER PULLEY, SS SCREW, CAP 3/8-6 X WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC 2 JWA 206 Page 5

6 ILLUSTRATION 2: LIFT GROUPING 206 JWA Page 6

7 PARTS LISTING - ILLUSTRATION 2: LIFT GROUPING PUMP, HYDRAULIC ELEC., VDC M-39 REPLACEMENT PARTS FOR PUMP: SOLENOID VALVE COIL PLUG, VENT (PLASTIC) 043 PLUG, SQUARE HEAD, /4 NPT 2 507R CABLE, EYE-EYE 4GA. X 24 (RED) SCREW, CAP 5/6-8 X -/ SCREW, CAP 3/8-6 X WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC FITTING, SWIVEL 90D, 3/8 X /4 NPT HOSE, HYDRAULIC /4NPT X 6-/2 LOA 9 66 VALVE, FLOW CONTROL NIPPLE, HEX /4 NPT (BRASS) HOSE, HYDRAULIC /4NPT X 5-/2 LOA CYLINDER, HYDRAULIC SPACER, CYL.REAR /2 ID X 2-/ WASHER, FLAT 3/4 SAE ZINC SCREW, CAP /2-3 X 3-/ WASHER, FLAT /2 SAE ZINC WASHER, LOCK /2 ZINC NUT, HEX /2-3 ZINC SCREW, CAP 5/8- X NUT, HEX LOCK 5/8- ZINC FORK, SS WHEEL 6 X 2-/2 X BRG., 2 RED POLY WASHER, BELLEVILLE 2 /2ID X 3/32THK WASHER, LOCK /2 ZINC SCREW, CAP /2-3 X BEARING, BALL TPB FITTING, GREASE /4-28 X SCREW, CAP 3/8-6 X 3-/ WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC KNOB, BALL -3/8 W/ /2-3THD SCREW, CAP /2-3 X 2-/ HANDWHEEL, SMALL W/ /2-3 THD NUT, HEX /2-3 ZINC WASHER, BELLEVILLE 2 /2ID X 3/64THK SPACER, STEEL /2 ID X LG ROD, ALLTHREAD LINKAGE /2-3 X LINKAGE LOWER TUBE, SS SCREW, DRIVE /8 X /4 L NUT /2-3, SPECIAL SCREW, CAP /2-20 X 2-/ NUT, HEX LOCK 5/8- ZINC PLUG, HOLE 2 JWA 206 Page 7

8 ILLUSTRATION 3: REAR AXLE GROUPING 206 JWA Page 8

9 PARTS LISTING - ILLUSTRATION 3: REAR AXLE GROUPING 5059 AXLE SHAFT DIA. X 25 L, SS KEY /4SQ X SPROCKET #40B34 X BORE BEARING, BALL TPB FITTING, GREASE /4-28 X RETAINING RING, EXT KEY /4SQ X WHEEL 8 X 3 X BORE WASHER, BELLEVILLE /2ID X 3/32THK WASHER, LOCK /2 ZINC SCREW, CAP /2-3 X SHIM, AXLE BEARING, SS SHIM, AXLE BEARING W/ ADJ.,SS SPACER, BEARING, SS BOLT, TAP /2-3 X 3 (FULL THREAD) WASHER, BELLEVILLE /2ID X 3/32THK WASHER, FLAT /2 SAE ZINC NUT, HEX /2-3 ZINC SCREW, CAP 3/8-6 X 3-3/ WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC CHAIN #40 X 25 + CL, SS-26 JWA 206 Page 9

10 ILLUSTRATION 4: TRANSMISSION, DRIVE LEVER & LINKAGE GROUPING 206 JWA Page 0

11 PARTS LISTING - ILLUSTRATION 4: TRANSMISSION, DRIVE LEVER & LINKAGE GROUPING A 5065 GRIP W/ ROCKER SWITCH INDIVIDUAL PARTS: GRIP BUILD KIT, 2 HALVES ROCKER SWITCH W/ WIRES CAP, RUBBER BOOT PLATE, DRIVE LEVER PRESSURE LEVER, DRIVE, SS SCREW, CAP /4-20 X -/ SPRING, COMP OD X.25 FL WASHER, FLAT /4 SAE ZINC NUT, HEX LOCK /4-20 ZINC GATE, DRIVE LEVER, SS SCREW, CAP STSHW X / SCREW, CAP /2-20 X -/ WASHER, BELLEVILLE /2ID X 3/64THK WASHER, FIBER 2-/4OD X /2ID X / WASHER, FLAT /2 SAE ZINC NUT, HEX LOCK /2-20 ZINC LINKAGE, ROD 3/8 X 4-5/8 L LINKAGE, ROD 3/8 X 5-3/4 L NUT, HEX 3/8-24 ZINC ROD END, FEMALE 3 3/8-24 R.H. THREAD 9 099L ROD END, FEMALE 3/8-24 L.H. THREAD SCREW, CAP 3/8-24 X -/ WASHER, FLAT 3/8 SAE ZINC NUT, HEX LOCK 3/8-24 ZINC BELLCRANK, DRIVE CONTROL TRANS. CONTROL ARM WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC NUT, HEX LOCK /2-3 ZINC WASHER, FLAT /2 SAE ZINC SCREW, CAP /2-3 X BELL CRANK, CLUTCH, SS MOUNT, TRANSMISSION, SS BOLT, CARRIAGE 3/8-6 X WASHER, GARRET 4 7/32 X X WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC TRANSMISSION, HYDROSTATIC KEY, WOODRUFF /8 X /2 3 (#404) SHEAVE, TRANS. 4 OD X GR. X.67 B FAN BLADE W/ PLATE 7, TRANSMISSION WASHER, LOCK /4 ZINC SCREW, CAP /4-20 X 3/ SPROCKET #35 X.67 BORE JWA 206 Page

12 ILLUSTRATION 5: CLUTCH LEVER & LINKAGE GROUPING 206 JWA Page 2

13 PARTS LISTING - ILLUSTRATION 5: CLUTCH LEVER & LINKAGE GROUPING 4023 KNOB, BALL -3/8 W/ /2-3THD, BLK LEVER, CLUTCH, SS SCREW, CAP 3/8-24 X -/ WASHER, FLAT 3/8 SAE ZINC NUT, HEX LOCK 3/8-24 ZINC LINKAGE, ROD 3/8 X 7 L ROD END, FEMALE 3/8-24 R.H. THREAD NUT, HEX 3/8-24 ZINC SCREW, CAP 3/8-24 X -/4 ZINC WASHER, LOCK 3/8 ZINC 0025 WASHER, FLAT 3/8 SAE ZINC NUT, HEX LOCK 3/8-24 ZINC SCREW, CAP /2-3 X WASHER, FLAT /2 SAE ZINC NUT, HEX LOCK /2-3 ZINC BELL CRANK, CLUTCH, SS CAM FOLLOWER BRG. 3/4 X 3/8-24THD WASHER, FLAT 3/8 SAE ZINC NUT, HEX LOCK 3/8-24 ZINC JWA 206 Page 3

14 ILLUSTRATION 6: CLUTCH GROUPING 206 JWA Page 4

15 PARTS LISTING - ILLUSTRATION 6: CLUTCH GROUPING BEARING, BALL 3/4 2-HOLE FLANGE FITTING, GREASE /4-28 X MOUNT, JACKSHAFT BEARING SCREW, CAP 3/8-24 X -/4 ZINC WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-24 ZINC SCREW, CAP 3/8-24 X COLLAR, LOCKING 3/4 ID CLAMP, HOSE, SAE #6, ADJ. TO -/ BELLOWS -/4ID X 2-3/8EL X -3/4RL SPRING, COMP. OD X 3.75 FL CLUTCH SPRING CUP WASHER, FLAT 3/4 SAE ZINC SEAL, OIL.750 X.375 X FITTING, GREASE /4-28 STRAIGHT CLUTCH, DOG BLOCK JACKSHAFT, CLUTCH -/2, SS KEY /4SQ X 2-/ KEY 3/6SQ X -/ SPROCKET, CLUTCH #35A A BEARING & CARRIER ASSY., CLUTCH BEARING, BALL 3/4ID X.8504 OD CARRIER, CLUTCH BEARING SCREW, SKT. HD. CAP 3/8-24 X -3/ SPACER, STEEL 9/6OD X 3/8ID X 7/ WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-24 ZINC CHAIN #35 X 24-/2 + CL MOUNT, TRANSMISSION, SS SPROCKET #40B0 X 3/4 BORE JWA 206 Page 5

16 ILLUSTRATION 7: ARBOR GROUPING 206 JWA Page 6

17 PARTS LISTING - ILLUSTRATION 7: ARBOR GROUPING ARBOR SHAFT 28-/8 L, SS BEARING, BALL -/2 TAP PIL. BLOCK FITTING, GREASE /4-28 X KEY 3/8SQ X 3-/ SHEAVE 5.30 OD X 6GR.3V X SK. (REQUIRES BUSHING) (30 BLADE SET-UP) BUSHING, SHEAVE SK X -7/6 BORE 4.80 OD X 6GR.3V X -7/6 B (8-26 BLADE SET-UP) 3.65 OD X 6GR.3V X -7/6 B (4-6 BLADE SET-UP) SCREW, SET 0-32 X / KEY /4SQ X SCREW, SET /4-28 X 5/ ARBOR BACKING PLATE 6 (30 BLADE SET-UP) 5 (4-26 BLADE SET-UP) ARBOR BLADE CAP 6 (30 BLADE SET-UP) 5 (4-26 BLADE SET-UP) PIN, SHEAR PROOF 3/8 X -/ COLLAR, LOCKING 5/8 ID (SET SCREW REMOVED) WASHER, LOCK, INT. TOOTH 5/ SCREW, CAP 5/8- X 3-/ SCREW, CAP /2-3 X WASHER, LOCK /2 ZINC WRENCH, ARBOR, 2 & 5/6 COMBO 2 2 JWA 206 Page 7

18 ILLUSTRATION 8: BLADE GUARD GROUPING 206 JWA Page 8

19 PARTS LISTING - ILLUSTRATION 8: BLADE GUARD GROUPING BLADE GUARD ASSEMBLY (ITEMS 2 THRU 6) 50735A* 57449A* 57450A* 5745A* *NOTE: DROP A SUFFIX FOR ITEMS 2, 3, 8, 9 0, &. 30 BLADE BLADE (SHOWN) 8-20 BLADE 4-6 BLADE F 57449F 57450F 5745F 50735R 57449R 57450R 5745R BLADE GUARD FRONT ONLY 30 BLADE BLADE (SHOWN) 8-20 BLADE 4-6 BLADE BLADE GUARD REAR ONLY 30 BLADE BLADE (SHOWN) 8-20 BLADE 4-6 BLADE 4 45 FLAP, RUBBER 2-/2 X SCREW, CAP /4-20 X 3/ WASHER, FLAT /4 SAE ZINC NUT, HEX LOCK /4-20 ZINC 8 67 HINGE, BUTT 3 X 3 X 7GA SCREW, CAP /4-20 X /2 ZINC WASHER, LOCK /4 ZINC WASHER, FLAT /4 SAE ZINC PIN & CABLE 30 BLADE GUARD BLADE GUARD 8-20 BLADE GUARD 4-6 BLADE GUARD FITTING, SWIVEL 45, /4NPT HYD CLAMP, HOSE, SAE #6, ADJ. TO 3/ HOSE, WATER /2 ID X 2 L BARBED FITTING, Y /2 HOSE HOSE /2 ID 22 L FOR 30 GUARD 24 L FOR GUARD 26 L FOR 4-6 & 8-20 GUARDS BARB, PUSH-ON /2HOSE X /2MPT CONN., MALE 3/4NH X /2FPT (BRASS) CONN., SWIVEL FEM. 3/4HOSE X /2MPT ELBOW, STREET /2NPT X 90 (BLACK) PIPE PLUG /2 NPT (BRASS) JWA 206 Page 9

20 ILLUSTRATION 9: WATER PUMP GROUPING 206 JWA Page 20

21 PARTS LISTING - ILLUSTRATION 9: WATER PUMP GROUPING 8002 CONN., SWIVEL FEM. 3/4HOSE X /2MPT 2 07A 07 VALVE & HOSE CONNECTOR ASSY. VALVE, BALL /2 FPT NIPPLE, HEX /2NPT (BRASS) ELBOW, STREET /2NPT X 45 (BLACK) BARB, /2HOSE X /2MPT (PLASTIC) CLAMP, HOSE, SAE #6, ADJ. TO 3/ HOSE, WATER /2 ID X 2 L STRAINER, NYLON T-STYLE /2FPT BARB ELBOW 90, /2HOSE X /2MPT HOSE, WATER /2 ID X 5-3/8 L PUMP, WATER, 2VDC, FLOJET QUAD (INCLUDES ITEM 2) PUMP QUAD PORT BARB ELBOW /2 2 (INCLUDED W/ PUMP, ITEM ) SCREW, CAP /4-20 X -/ WASHER, FLAT /4 SAE ZINC NUT, HEX LOCK /4-20 ZINC WASHER, LOCK /4 ZINC NUT, ACORN / HOSE, WATER /2 ID X 7-5/8 L PIPE NIPPLE, CLOSE /2NPT (BLACK) PIPE TEE, WATER PRESS. SW. /2 NPT SWITCH, PRESSURE, N/C PIPE PLUG /2 NPT (BRASS) HOSE, WATER /2 ID X 20 L, SS CLAMP, LOOM, 5/8 (SAE SIZE 0) RUBBER PIECE REMOVED SCREW, CAP /4-20 X NUT, KEPS LOCK /4-20 ZINC FUSE & HOLDER, 0 AMP JWA 206 Page 2

22 ILLUSTRATION 0: INSTRUMENT PANEL GROUPING 5065 INSTRUMENT PANEL, SS26-35K GROMMET -/4ID X /8GRV. X -/2GD 3 59 ROPE CLEAT, NYLON JAM 3/6-5/ SCREW, MACHINE 0-32 X 5/8, SLT.FLT NUT, KEPS LOCK 0-32 ZINC SCREW, CAP /4-20 X 3/ SCREW, CAP /4-20 X WASHER, LOCK /4 ZINC WASHER, FLAT /4 SAE ZINC JWA Page 22

23 ILLUSTRATION : BLADE DEPTH GAUGE GROUPING 5732 WHEEL, DEPTH GAUGE SCREW, CAP 3/8-24 X 2-/ WASHER, FLAT 3/8 SAE ZINC NUT, HEX LOCK 3/8-24 ZINC CABLE, DEPTH GAUGE 3/32 X 34 L SPRING, EXT. 6 L SCREW, CAP /4-20 X NUT, KEPS LOCK /4-20 ZINC WASHER, FLAT /4 SAE ZINC NUT, HEX NYLON LOCK /4-20 ZINC 2 JWA 206 Page 23

24 ILLUSTRATION 2: OPERATING CONTROLS WATER HOOK-UP AND VALVE (ILLUS. 9) EXTENDABLE HANDLES (ILLUS. ) 2 3 HANDLE LOCK KNOB, STAR CLAMPING 3/8-6 X STUD (ILLUS. ) DEPTH CONTROL (ILLUS. 2) AMMETER YE2, 30 OR 60 AMP METER, HOUR 2-/ WATER PUMP SWITCH, TOGGLE SPST BLADE SAVER SWITCH, TOGGLE SPST DEPTH INDICATOR (ILLUS. ) LOW OIL INDICATOR LAMP, OIL PRESSURE, RED 5266 IGNITION SWITCH, KEY, KOHLER S CHOKE CABLE, CONTROL ROPE CLEAT, NYLON JAM 3/6-5/6 (ILLUS. 0) THROTTLE CABLE, VERNIER ADJ. LOCKING CONTROL DRIVE LEVER W/ BLADE LIFT/LOWER SWITCH (ILLUS. 4) G SWITCH, E-STOP W/ GREEN N.O.CONTACT INCLUDES: PUSHBUTTON, TURN TO RELEASE E-STOP MOUNTING ADAPTER, PUSHBUTTON CONTACT ELEMENT, NO GREEN LM2TC CLUTCH CONTROL LEVER (ILLUS. 5) 206 JWA Page 24

25 ILLUSTRATION 3: GUIDE BAR ASSEMBLY 579A GUIDE BAR ASSEMBLY (INCLUDES ITEMS 2 THRU 9) GUIDE BAR SCREW, CAP /2-20 X NUT, HEX NYLON LOCK /2-20 ZINC POINTER, FRONT 24-/ WHEEL 5 X -/2 X 3/4 BORE AXLE TUBE, GUIDE WHEEL SPACER TUBE 5-/6, GUIDE BAR WHEEL SCREW, CAP /2-20 X ROPE, GUIDE BAR (NOT INCLUDED W/ GUIDE BAR ASSY.) JWA 206 Page 25

26 ILLUSTRATION 4: ENGINE & MOUNT GROUPING 206 JWA Page 26

27 PARTS LISTING - ILLUSTRATION 4: ENGINE & MOUNT GROUPING ENGINE, KOHLER 35HP COMMAND PRO PA-CH AIR FILTER REPLACEMENTS: ELEMENT, AIR FILTER - PRIMARY (OUTER) ELEMENT, AIR FILTER - SECONDARY (INNER) KS MOUNT, GASOLINE ENGINE, SS BOLT, CARRIAGE 3/8-6 X 2 GRADE WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC BRACKET, ENGINE MOUNT, SS SCREW, CAP /2-20 X -/ SCREW, CAP /2-20 X WASHER, FLAT /2 SAE ZINC NUT, HEX LOCK /2-20 ZINC SCREW, CAP /2-3 X 3-/ WASHER, FLAT /2 SAE ZINC WASHER, LOCK /2 ZINC NUT, HEX /2-3 ZINC SCREW, CAP /2-3 X -/ WASHER, FLAT /2 SAE ZINC WASHER, LOCK /2 ZINC NUT, HEX /2-3 ZINC BOLT, TAP /2-3 X 5 (FULL THREAD) NUT, HEX /2-3 ZINC TOGGLE PAD 7/8 D X 5/6 H X / ARM, IDLER, SS SCREW, CAP 3/8-24 X 2-/ IDLER PULLEY 3 OD X GR.AB X 3/8 B SPACER, STEEL 9/6OD X 3/8ID X 7/ NUT, HEX LOCK 3/8-24 ZINC WASHER, FLAT 3/8 SAE ZINC SPRING, EXT. OD X 3-5/6 JWA 206 Page 27

28 ILLUSTRATION 5: BELT DRIVE GROUPING 206 JWA Page 28

29 PARTS LISTING - ILLUSTRATION 5: BELT DRIVE GROUPING BELT (ARBOR) SEE CHART VX-450 3VX BELT A-55 (TRANSMISSION) 3 SHEAVE (ARBOR) SEE CHART BELOW & ILLUS. 7, ITEM OD X 6GR.3V X SK (REQUIRES BUSHING) BUSHING, SHEAVE SK X -7/6 BORE 4.80 OD X 6GR.3V X -7/6 B 3.65 OD X 6GR.3V X -7/6 B SHEAVE 2.8 OD X 6GR.3V X -7/6 B (ENGINE) SCREW, SET 0-32 X / KEY 3/8SQ X 3-/ BUSHING, TAPER-LOCK 60-7/6 B SHEAVE 4.5 OD X GR.AB X TPR-LOCK IDLER PULLEY 3 OD X GR.AB X 3/8 B (SEE ILLUS. 4, ITEM 25) SHEAVE, TRANS. 4 OD X GR. X.67 B (SEE ILLUS. 4, ITEM 38) 5007 KEY, WOODRUFF /8 X /2 (#404) ENGINE TYPE KOHLER GASOLINE CH HP MODEL SS26-35K ENGINE RPM 3600 BLADE DIAMETER BELT DRIVE SPECIFICATION CHART BLADE SPEED (RPM) ENGINE SHEAVE 2.80 (050) ARBOR SHEAVE 3.65 (05) ARBOR BELT (6 REQ D.) 3VX425 (50498) 4.80 (052) 3VX450 (0228) 5.30 (50724) TRANSMISSION BELT A55 (0284) JWA 206 Page 29

30 ILLUSTRATION 6: FUEL TANK GROUPING 206 JWA Page 30

31 PARTS LISTING - ILLUSTRATION 6: FUEL TANK GROUPING TANK, FUEL 6.4 GAL. SS CAP, FUEL TANK W/ VITON GASKET PIPE PLUG /8 NPT (BRASS) TUBE, FUEL PICK-UP 9-3/4, SS BARB ELBOW 90, /4HOSE X /8MPT CLAMP, HOSE, SPRING-BAND 7/6 RED TUBING, EVAP LOW PERM. FUEL /4 ID X 44 L 3.67 FT TUBING, EVAP LOW PERM. FUEL /4 ID X 5 L.25 FT SCREW, CAP /2-20 X -/ WASHER, FLAT /2 SAE ZINC NUT, HEX LOCK /2-20 ZINC PIN, DETENT RING /2 X -/2 E.L GROMMET -45/64ID X /8GRV. X 2GD GROMMET 3/8ID X /8GRV. X 5/8GD 2 (I.D. OPENED UP FOR FUEL LINE) CLAMP, LOOM, 5/8 (SAE SIZE 0) CANISTER, CARBON A FOR KOHLER TIE, CABLE, BLACK NYLON -/ SCREW, CAP /4-20 X /2 ZINC WASHER, LOCK, INT. TOOTH / CLAMP, HOSE, SPRING-BAND 3/8 GREEN TUBING, EVAP LOW PERM. FUEL 3/6 ID X 2 L.75 FT TUBING, EVAP LOW PERM. FUEL /4 ID X 8 L.5 FT FILTER, FUEL /4 IN LINE CLAMP, LOOM, -5/ SCREW, CAP /4-20 X 3/ WASHER, FLAT /4 SAE ZINC NUT, KEPS LOCK /4-20 ZINC JWA 206 Page 3

32 ILLUSTRATION 7: OIL DRAIN GROUPING PIPE PLUG /2 NPT (BRASS) SCREW, CAP /4-20 X 3/ WASHER, LOCK /4 ZINC WASHER, FLAT /4 SAE ZINC BRACKET, OIL DRAIN, SS BARB, PUSH-ON /2HOSE X /2MPT HOSE, PUSH-ON /2 ID X 6-/2 L ELBOW, STREET /2NPT X 45 (BLACK) 206 JWA Page 32

33 ILLUSTRATION 8: BATTERY GROUPING 5032 BATTERY 2 VOLT/500 CCA(POST TERM.) INTERSTATE MT-5R INSULATOR, BAT.TERM.POST (RED) CABLE, BATTERY 4GA. X 53 (RED) LOOM, FLEX 5/8 X 52 L, SS26-35K INSULATOR, BAT.TERM.POST (BLACK) B CABLE, BATTERY 4GA. X 2 (BLACK) WIRE, GROUND, 0GA X 6, SS26-35K TRAY, BATTERY, SS26-35K/5B NOTE: TRAY FOR INTERSTATE MT-5R BATTERY SCREW, CAP 3/8-6 X -/4 SCREW, CAP 3/8-6 X 3/ WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK, INT./EXT. TOOTH 3/ NUT, HEX 3/8-6 ZINC STRAP, BATTERY, SS26-35K/5B NOTE: STRAP FOR INTERSTATE MT-5R BATTERY SCREW, CAP /4-20 X WASHER, FLAT /4 SAE ZINC WASHER, LOCK /4 ZINC NUT, HEX LOCK /4-20 ZINC 2 3 JWA 206 Page 33

34 WIRING DIAGRAM FOR SS26-35K 206 JWA Page 34

35 DECAL SHEET P/N JWA 206 Page 35

36 DECAL SHEET P/N DECAL KIT Model SS-26 Model SS-36 PN: RevB SS-26 CHECK OIL DAILY GREASE BEARINGS DAILY R edcoinc.com SS JWA Page 36

37 DECAL SHEET P/N JWA 206 Page 37

38 THIS PAGE WAS LEFT BLANK INTENTIONALLY 206 JWA Page 38

39 NOTES Record here any repairs or changes made to the Equipment JWA 206 Page 39

40 LIMITED EQUIPMENT WARRANTY OF SALE - TERMS & CONDITIONS Equipment Development Company, Inc. herein referred to as EDCO (Seller) warrants that each new unit manufactured by EDCO to be free from defects in material and workmanship in normal use and service for a period of () one year (except for the cutter drum assembly on all model concrete/asphalt planes, in which case the warranty period shall be 90 days) from date of shipment to the original retail or equipment rental center owner. Accessories or equipment furnished and installed on the product by EDCO but manufactured by others, including, but not limited to engines, motors,electrical components, transmissions etc., shall carry the accessory manufacturers own warranty. EDCO will, at its option, repair or replace, at the EDCO factory or at a point designated by EDCO, any part which shall appear to the satisfaction of EDCO inspection to have been defective in material or workmanship. EDCO reserves the right to modify, alter and improve any part or parts without incurring any obligation to replace any part or parts previously sold without such modified, altered or improved part or parts. This warranty is in lieu of and excludes all other warranties, expressed, implied, statutory, or otherwise created under applicable law including, but not limited to the warranty of merchantability and the warranty of fitness for a particular purpose in no event shall seller or the manufacturer of the product be liable for special, incidental, or consequential damages, including loss of profits, whether or not caused by or resulting from the negligence of seller and/or the manufacturer of the product unless specifically provided herein. In addition, this warranty shall not apply to any products or portions there of which have been subjected to abuse, misuse, improper installation, maintenance, or operation, electrical failure or abnormal conditions and to products which have been tampered with, altered, modified, repaired, reworked by anyone not approved by seller or used in any manner inconsistent with the provisions of the above or any instructions or specifications provided with or for the product. FORCE MAJEURE Seller s obligation hereunder are subject to, and Seller shall not be held responsible for, any delay or failure to make delivery of all or any part of the Product due to labor difficulties, fires, casualties, accidents, acts of the elements, acts of God, transportation difficulties, delays by a common carrier, inability to obtain Product, materials or components or qualified labor sufficient to timely perform part of or all of the obligations contained in these terms and conditions, governmental regulations or actions, strikes, damage to or destruction in whole or part of manufacturing plant, riots, terrorist attacks or incidents, civil commotions, warlike conditions, flood, tidal waves, typhoon, hurricane, earthquake, lightning, explosion or any other causes, contingencies or circumstances within or without the United States not subject to the Seller s control which prevent or hinder the manufacture or delivery of the Products or make the fulfillment of these terms and conditions impracticable. In the event of the occurrence of any of the foregoing, at the option of Seller, Seller shall be excused from the performance under these Terms and Conditions, or the performance of the Seller shall be correspondingly extended. This document sets forth the terms and conditions pursuant to which the purchaser ( Purchaser ) will purchase and Equipment Development Co.Inc. ( Seller )will sell the products, accessories, attachments (collectively the Products ) ordered by the Purchaser. These terms and conditions shall govern and apply to the sale of Seller s Products to Purchaser, regardless of any terms and conditions appearing on any purchase order or other forms submitted by Purchaser to Seller, or the inconsistency of any terms therein and herein.. PRICE All prices set forth on any purchase order or other document are F.O.B. Sellers facility or distribution point, as may be determined by Seller (F.O.B.Point). All prices are exclusive of any and all taxes, including, but not limited to, excise, sales, use, property or transportation taxes related to the sale or use of the Products, now or hereafter imposed, together with all penalties and expenses. Purchaser shall be responsible for collecting and/or paying any and all such taxes, whether or not they are stated in any invoice for the Products. Unless otherwise specified herein, all prices are exclusive of inland transportation, freight, insurance and other costs and expenses relating to the shipment of the Products from the F.O.B. point to Purchaser s facility. Any prepayment by Seller of freight insurance and other costs shall be for the account of Purchaser and shall be repaid to Seller. 2. PAYMENT TERMS Payment terms are as follows. 2% 0 days (to approved and qualified accounts). Net 30 days. This is a cash discount for invoices paid within 0 days after the invoice date, regardless of date of receipt of shipment. This is not a trade discount and will not be granted to accounts that do not adhere to stated terms. *All past due accounts are subject to a late payment fee of.5% per month or a maximum allowed by law if different, along with the expenses incidental to collection including reasonable attorney s fees and costs. *Seller reserves the right to hold shipments against past due accounts. *Seller reserves the right to alter payment terms. 3. FREIGHT TERMS All shipments will be made F.O.B. shipping point as designated in these Terms and Conditions, and title shall pass at the F.O.B. point. Delivery to the initial common carrier shall constitute delivery to the Purchaser. Any claims for loss or damage during shipment are to be filed with carrier by the Purchaser. Seller will not assume responsibility for the performance of the carrier. Back orders will be shipped in the most practical fashion with charges consistent with our freight policy established with the original order. UPS, FED EX, MAIL or shipments by other couriers are subject to the same terms and conditions as outlined in paragraph #3 Freight Terms. 4. DELIVERY, DAMAGES, SHORTAGES Seller shall use reasonable efforts to attempt to cause the Products to be delivered as provided for in these Terms & Conditions. Delivery to the initial common carrier shall constitute the delivery to the Purchaser. Sellers responsibility, in so far as transportation risks are concerned ceases upon the delivery of the Products in good condition to such carrier at the F.O.B. point and all the Products shall be shipped at the Purchaser s risk. Seller shall not be responsible or liable for any loss of income and/or profits, or incidental, special, consequential damages resulting from Seller s delayed performance in shipment and delivery. 5. RETURN OF DEFECTIVE PRODUCTS Defective or failed material shall be held at the Purchaser s premises until authorization has been granted by Seller to return or dispose of Products. Products that are to be returned for final inspection must be returned Freight Prepaid in the most economical way. Credit will be issued for material found to be defective upon Seller s inspection based on prices at time of purchase. 6. PRODUCTS ORDERED IN ERROR Products may be returned, provided that claim is made and Seller is notified within 7 days of receipt of Products, and the Products are in original buyer s possession not more than 30 days prior to return, subject to Seller s approval. If Products are accepted for return, they must be Freight Prepaid and buyer will be charged a minimum of 5% restocking charge, plus a charge back for outbound freight charges if the original order was shipped prepaid. Returns are not accepted for any Products that are specifically manufactured to meet the buyer s requirement of either specifications or quantity. AGREEMENTS These Terms and Conditions constitute the entire agreement between Seller and Purchaser as it relates to terms and conditions of sale, and supersedes any and all prior oral or written agreements, correspondence, quotations or understandings heretofore in force between the parties relating to the subject matter hereof. There are no agreements between Seller and Purchaser with respect to the Product herein except those specifically set forth in and made part of these terms and conditions. Any additional terms, conditions and/or prices are rejected by Seller. These terms and conditions may be modified, cancelled or rescinded only by a written agreement of both parties executed by their duly authorized agents. USE ONLY GENUINE EDCO PARTS & ACCESSORIES For your own safety, the safety of others and the life of your machine. Equipment Development Company, Inc. 206 JWA Page 40