EDGEMERE DUAL CONTROL WIDESPREAD LAVATORY FAUCET INSTALLATION INSTRUCTIONS

Transcription

1 EDGEMERE DUAL CONTROL WIDESPREAD LAVATORY FAUCET INSTALLATION INSTRUCTIONS 0.0 Thank you for selecting American Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A..M RECOMMENDED TOOLS A Flat Head Screwdriver Slip Jaw Pliers Adjustable Wrench Tubing Cutter INSTALL SPOUT Fig. A. CAUTION Turn off hot and cold water supplies before begining. Insert SHANK () POP-UP ROD () and HOSE () through center hole, making sure SEAL WASHER () is properly seated in spout base. Assemble RUBBER WASHER (), FRICTION WASHER (A) LOCKNUT () and thread LOCKNUT () onto SHANK () from underside of sink or mounting surface. Align and center SPOUT (). Tighten LOCKNUT (). INSTALL VALVE BODIES Fig. B. Remove LOCKNUT () and WASHER (9) and (9a) from SIDE VALVE SHANKS (0). Insert Hot and Cold SIDE VALVE HOSES (), FLEXIBLE SUPPLIES (a) into mounting holes making sure the SEAL WASHERS () are properly seated in each HANDLE BASE (). Assemble RUBBER WASHER (9), FRICTION WASHER (9A) and thread LOCKNUT () onto each SIDE VALVE SHANK (0) from underside of sink or mounting surface. Align and center SIDE VALVES. Tighten LOCKNUTS (). Fig. B. Fig. A. SPOUT BASE A 0 9 9A a a Blue Stripe (COLD) Red Stripe (HOT) Product names listed herein are trademarks of AS America, Inc. AS America, Inc M90 (/)

2 INSTALL POP-UP DRAIN a Apply a bead of putty to underside of FLANGE (). Drop FLANGE () into LAVATORY DRAIN (). From below assemble RUBBER GASKET (), METAL WASHER () and LOCK NUT (). Do not tighten. b Place SEAL () with small end facing up into TAILPIECE () and tighten against DRAIN BODY (). PIVOT ROD () opening in TAILPIECE () should face the rear of the lavatory. Tighten LOCK NUT () with channel locks. Do not over tighten. c Assemble PIVOT ROD (), PIVOT NUT (), CLIP () and SEAL () as shown. Hand tighten PIVOT NUT () Drop STOPPER () into drain. (For vandal proof drain rotate stopper so PIVOT ROD () goes through EYE () of STOPPER (). Make connection to P TRAP. Remove one end of CLIP () from PIVOT ROD () by squeezing ends together while sliding. Insert PIVOT ROD () into second or third hole in EXTENSION () and reassemble CLIP (). (EXTENSION () may need to be bent.) Adjust STOPPER () height by repositioning EXTENSION () and tightening THUMBSCREW (). - - M90 (/)

3 CHECK OPERATION OF POP-UP Operate LIFT KNOB () to verify that STOPPER () opens and closes. Note: If STOPPER () does not open and close properly then refer to the troubleshooting section of these instructions. MAKE WATER SUPPLY AND WASTE CONNECTIONS Connect FLEXIBLE SUPPLIES (, ) directly to wall supplies. Connection on fitting supplies are /" compression. Connect FLEXIBLE SUPPLY () (Marked with a Red Band) to the Left wall supply and FLEXIBLE SUPPLY () (Marked with a Blue Band) to Right wall supply. Connect the VALVE HOSES (, a) to SPOUT TEE (). Use adjustable wrench to tighten connections. Do not over tighten. Faucet supplies are 0" long from faucet base. Note: If additional supply length is required, installer must purchase additional parts separately. Important: If SUPPLY HOSES (, ) are to long, loop as illustrated to avoid kinking. Connect -/" O.D. tailpiece on POP-UP DRAIN to waste outlet. a Blue Stripe (C0LD) Red Stripe (HOT) WASTE OUTLET COLD HOT - - M90 (/)

4 TEST INSTALLED FITTING With HANDLE () in OFF position, turn on WATER SUPPLIES () and check all connections for leaks. Remove AERATOR (). Operate HANDLE () to flush water lines thoroughly. Replace AERATOR (). CHECK DRAIN CONNECTIONS Operate POP-UP KNOB () and fill lavatory with water. Check that DRAIN STOPPER () makes a good seal and retains water in Sink. If DRAIN STOPPER () does not seal properly, please refer to Troubleshooting section in these instructions. Release POP-UP KNOB () down and check all drain connections and P trap for leaks. Tighten if necessary. WASTE OUTLET HOT COLD P TRAP SERVICE Change Direction of the Handle Turn valves to OFF position. Turn off water supplies. Pull HANDLE () UP firmly to release from PLASTIC INSERT (). Remove SCREW () and pull off PLASTIC INSERT (). Remove RETAINING O-RING (). Lift and turn STOP WASHER () 90. Replace RETAINING O-RING (). Re-install HANDLE ASSEMBLY. To Change Cartridge: Remove HANDLE (), ADAPTER () and SCREW () via steps above. Loosen CARTRIDGE NUT () by turning counterclockwise then pull up on cartridge to remove Aerator Clean Out AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR by using the AERATOR KEY and rinse to clear any debris. If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90. CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. - - M90 (/)

5 Replace the YYY with appropriate finish code CHROME 00 BRUSHED NICKEL 9 LEGACY BRONZE EDGEMERE DUAL CONTROL WIDESPREAD LAVATORY FAUCET MODEL NUMBER 0.0 M90-YYY0A Lift Rod and Knob M90009-YYY0A Handle Kit (Before August 0) M A Aerator Kit M900-YYY0A Handle Kit (After August 0) M90-YYY0A Valve Kit M A Valve M A T-Connector M A Mounting Kit M9-YYYOA Drain Assembly - - HOT LINE FOR HELP For toll-free information and answers to your questions, call: (00) -90 Mon. - Fri. :00 a.m. to :00 p.m. EST Saturday 0:00 a.m. to :00 p.m. EST IN CANADA (TORONTO ) Weekdays :00 a.m. to :00 p.m. EST IN MEXICO M90 (/)