HISD FOOD SERVICES. Kitchen Equipment Specifications TN-BOOK

Transcription

1 HISD FOOD SERVICES Kitchen Equipment Specifications TN-BOOK April

2 TABLE OF CONTENTS GENERAL CONDITIONS... 7 III. SCOPE OF WORK AND SPECIFIC CONDITIONS SCOPE OF WORK: SPECIFIC CONDITIONS: SEE FORM F - PRICE SCHEDULE ATTACHED SPECIFICATIONS: AWARDS GENERAL REQUIREMENTS MAINTENANCE AND SERVICE QUALIFICATIONS GUARANTEE APPROVAL ALTERNATES EXCEPTIONS PRODUCT RECALL ORDERS / DELIVERIES / INVOICING TITLE AND RISK OF LOSS LEAD TIME CONTRACT PERFORMANCE CONTRACT TERM FIRM PRICES REFERENCES PAYMENT TERMS EQUIPMENT TESTING AND APPROVAL PROCEDURES OBJECTIVE PROCEDURE FOOD PREP EQUIPMENT VEGETABLE PRESS, MANUAL, BIPOD BASE TN VEGETABLE PRESS, MANUAL, WALL MOUNT TN-004A SLICERS TN FOOD PROCRSSOR TN MIXER 20QT TN-010A MIXER 30QT TN-010B MIXER 60QT TN-010C CAN OPENER, ELECTRIC TN WEDGE SECTIONIZER

3 TN CAN OPENER, MANUAL TN-107A BLENDER TN REFRIGERATION MILK COOLER, DOUBLE DROP FRONT (8 CASE) TN-020A MILK COOLER, DUAL- ACCESS TWIN TOP (12 CASE) TN FREEZER, CHEST, 25 CU. FT TN FREEZER, CHEST, 20 CU. FT TN ICE CREAM FREEZER, 4 SQUARE TN ICE CREAM FREEZER, TWO IN LINE TN-053A REFRIGERATOR, ONE SECTION TN REFRIGERATOR, ONE SECTION TN-270PT REFRIGERATOR, ONE DOOR TN-270A REFRIGERATOR, ONE DOOR PASS THRU TN-270A /PT REFRIGERATOR, TWO SECTION TN REFRIGERATOR, TWO SECTION TN-280PT REFRIGERATOR, TWO DOOR TN-280A REFRIGERATOR, TWO DOOR PASS THRU TN-280A/PT REFRIGERATOR, THREE SECTION TN REFRIGERATOR, THREE DOOR TN-290A FREEZER, ONE SECTION TN FREEZER, ONE DOOR TN-300A FREEZER, TWO SECTION TN TN-310A TN FREEZER, THREE DOOR TN-320A ICE MACHINE, 300 LB. PRODUCTION TN ICE MACHINE, 500 LB. PRODUCTION TN ICE STORAGE BIN TN

4 WALK-IN COOLER/FREEZER SPECIFICATIONS WALK-IN COOLER/FREEZER SPECIFICATIONS TN WALK-IN COOLER/FREEZER SPECIFICATIONS, SELF CONTAINED TN-078SC TRANSPORT AND STORAGE CART, DISH, POLYETHYLENE TN CART, DISH, STAINLESS STEEL TN DOLLY, MILK CASE TN ULTRA PAN CARRIERS TN CAMDOLLY STRAP TN-123AB CAMCARTS, FOR FOOD BOXES AND TRAYS/SHEET PANS TN-123A RACK, BUN TN SHELVING, SOLID TN-O78A SHELVING, VENTED TN-078C DUNNAGE RACK TN-078B SHELVING STARTER UNITS (SOLID AND VENTED) TN SHELVING ADD-ON KITS (SOLID AND VENTED) TN-592A COMBINATION SAFE TN COOKING APPLIANCES OVEN, GAS, DOUBLE CONVECTION WITH PLAIN DOORS TN-041A RANGE, GRATE TOP TN RANGE, GRATE TOP WITH CONVECTION OVEN TN TWO COMPARTMENT FORCED CONVECTION STEAMER ON 24 INCH CABINET BASE TN STEAMER WITHOUT BOILER TN STAND FOR TN-590 STEAMER TN-590A CABINET, HOT PASS THRU, SUPER BAR TN CABINET, HOT, SUPER BAR TN TWO SIDED GRILL TN

5 ROUND COOKER WARMER TN HOT FOOD HOLDING CABINET, ONE SECTION TN HOT FOOD HOLDING CABINET, ONE SECTION TN-410PT HOT FOOD HOLDING CABINET, TWO SECTION TN HOT FOOD HOLDING CABINET, TWO SECTION TN-420PT HOT FOOD HOLDING CABINET, THREE SECTION TN SANITATION WASHER, CLOTHES TN DRYER, CLOTHES TN-007A WASHER/DRYER, STACKABLE TN-007B DISPOSER (2 HP) TN DISPOSER (1 HP) TN-037A WATER HEATER TN TABLE AND SINKS TABLE, WORK (4') TN TABLE, COOK WITH POT RACK AND SINK (10') TN TABLE, COOK (10') TN-022A TABLE, WORK (6') TN-022B TABLE, COOK (10') WITH POT RACK, LESS SINK TN-022C TABLE, WORK (6') WITH POT RACK TN-022D TABLE, WORK (8') TN-022E TABLE, WORK (8') WITH POT RACK TN-022F TABLE, COOK (8') WITH SINK TN-022G TABLE, BAKER'S WITH BINS (8') TN SINK CONSTRUCTION I. GENERAL II. MATERIALS III. CONSTRUCTION SINK, POT AND PAN

6 TN SINK, VEGETABLE TN SERVING LINE GENERAL REQUIREMENT SERVING UNIT COLD 3 PAN SIZE WITH DOUBLE TIER DISPLAY STAND TN-069SS SERVING UNIT HOT 5 PAN SIZE WITH SINGLE TIRE SERVING SHELF TN-070ESS SERVING UNIT 3 PAN UNIT FLAT UNIT TN-071SS SERVING UNIT CASHIER TABLE TN-072SS HOT PAN DROP IN UNIT SINGLE PAN TN-114A HOT PAN DROP-IN, THREE PAN TN-114C HOT PAN DROP-IN, FOUR PAN TN-114D HOT PAN DROP-IN UNIT, 5 PAN TN-114E REFRIGERATED DROP-IN, THREE PAN TN-120C UTILITY DISTRIBUTION SYSTEM COOK LINE TN SERVING COUNTER TN

7 GENERAL CONDITIONS III. SCOPE OF WORK AND SPECIFIC CONDITIONS 3.1 SCOPE OF WORK: The Houston Independent School District ( HISD and/or the District ) is soliciting proposals for Kitchen Equipment for the school kitchens and cafeterias. At minimum, the scope of services required to be provided by the selected firm shall consist of the following (required services are not listed in any priority order): Awarded vendors are to deliver, uncrate, and set in place (location will be specified at time of delivery and or on the purchase order). Awarded contracts will be for one year starting August 1, 2013 and ending July 31, Drop shipments direct from factories are not acceptable. HISD will make the sole and final determination regarding specifications, quality, performance levels, and interchangeability, in regard to bid items. Your proposal needs to be legible and submitted in triplicate with an original manual signature of a company officer. Prospective proposers are advised that proposals not conforming to the standards stated in this paragraph will not be considered. 3.2 SPECIFIC CONDITIONS: See Form F - Price Schedule attached 3.3 SPECIFICATIONS: No proposals will be acceptable unless the following qualifications can be verified to the satisfaction of the Houston Independent School District. These project specific general conditions are in addition to the HISD School District General Conditions listed in section II GENERAL TERMS AND CONDITIONS HISD SCHOOL DISTRICT above AWARDS Proposals will be evaluated on a line item basis. Actual award method will be determined by considering product performance, price, service, and ability to perform according to the terms and conditions of this project to fit the needs of HISD. HISD reserves the right to accept or reject any RFP (in whole or in part), negotiate with the proposers, waive formalities, and make multiple awards in a manner that is most advantageous and beneficial to HISD GENERAL REQUIREMENTS All equipment specified here after shall be fabricated to conform to the requirements and bear the seal for acceptance of the American Gas Association, National Sanitation Foundation, Underwriters Laboratories, City of Houston, County, and / or State Code as indicated for each piece of equipment. All equipment and materials shall be new, latest design and of first quality. Workmanship shall be of highest grade throughout and in accordance with the Houston Independent School District equipment specifications. All equipment to be replaced, shall be removed from the job site unless noted differently on the purchase order. 7

8 All items shall be inspected for workmanship and conformity to specifications upon delivery. Items not so conforming or that have been damaged shall not be accepted or installed. The Successful Bidder shall, at all times cover and protect his work, materials, fixtures and apparatus to be used therein, from any damage or loss by weather or otherwise, and shall exercise due care to save same from damage. All damage resulting from such neglect shall be made good by the successful bidder. The Successful Bidder of any item shall provide a black and white photograph or line drawing as appropriate for the specific item to HISD Food Services Purchasing within ten (10) working days from the date of issue of an award letter announcing HISD Board of Education approval. Only genuine photographs or original line drawings will be accepted. Cut sheets, brochures, photocopies, or any printed material will not be considered acceptable. Failure to provide an acceptable photograph or line drawing within ten (10) days will be cause for automatic award to the next lowest bidder. Any awarded item not shipped within the estimated delivery schedule will be cause for automatic cancellation of the order unless otherwise approved by Owner. 3.3 MAINTENANCE AND SERVICE QUALIFICATIONS No equipment will be accepted unless the following qualifications can be verified to the satisfaction of the Houston Independent School District. Established replacement parts and service shall be available locally. Equipment factory representative must be available for consultation and individual school operating instruction upon installation of any item of equipment. Successful Bidder must provide a local telephone number or a toll free telephone number for technical support and Houston factory representation upon request. Manufacturer must supply ten (10) copies each of Service Repair Manual and Parts Manual for each item awarded GUARANTEE The Successful Bidder shall give the Owner a written guarantee covering all material and workmanship of the equipment furnished under these specifications, for a period of one (1) year or as specified for the specific piece of equipment, after acceptance by Owner. The Successful Bidder shall replace any defective equipment in whole or in part, as may be necessary, during the guarantee/warranty period. The Successful Bidder shall provide full instructions and demonstrate to the Owner's designated representative proper methods of care, operation and servicing of the equipment. All equipment contained herein is to have one (1) year parts and labor warranty unless otherwise stated. All refrigerator and/or freezer compressors shall be guaranteed for five (5) years. Successful Bidder will be held responsible for compressor replacements, and any freight charges associated with replacements, as needed during the entire five (5) years APPROVAL All brands submitted for approval as an equal are subject to review and approved by Food Services. The decision of HISD Office of Food Services will determine the acceptance or rejection of brands submitted for an approved equal. 8

9 3.3.6 ALTERNATES Food Services cannot anticipate all trends in the market place and encourages all bidders to submit a complete, condensed list of alternate products available in addition to the formal line items listed in the bid, at the price the bidders will sell them for the length of the bid period, in the event of product shortages, plant closures, acts of God, and expectations. Should any of these occur during the bid period, HISD reserves the right to call for samples from the list of alternates submitted, and select items from the list of alternates by choosing the lowest alternate bid item and or best meeting the Districts needs and requirements EXCEPTIONS Proposer(s) are responsible for identifying any exceptions to the requirements and terms and conditions herein. Any exceptions to the terms and conditions specified herein must be indicated on the proposer s letterhead, and returned with the RFP. RFP s which are qualified with conditional clauses or terms may be considered non-responsive by HISD PRODUCT RECALL If a product recall is instituted on any of the awarded items that are being used by HISD, the successful proposer(s) will immediately notify Sourcing Specialist, Beth or Procurement Sr. Sourcing Manager, Elvis ORDERS / DELIVERIES / INVOICING Successful Bidder must provide a local telephone number or a toll free telephone number for both voice and facsimile transmissions and address. Successful Bidder will confirm receipt of their orders and delivery date therein with Rhonda Carroll-Johnson at ; rcarrol1@houstonisd.org. Upon receipt of confirming phone call a purchase order number will be issued. Please reference the ship to location and product requested to identify the order when calling. Successful Bidder must make a delivery appointment with the HISD maintenance personnel prior to all deliveries. The individuals designated as Contact Persons are listed below along with their respective phone numbers and address. Contact Person Office Phone Robert Koch (Bobby) rkoch@houstonisd.org Refrigeration / Electrical Kelvin Bryan kbryan@houstonisd.org Mechanical / Plumbing Lyndia Tarkington ltarking@houstonisd.org Transportation & Storage / Clerical All deliveries require the kitchen manager's signature. A signed delivery ticket (or invoice) must be submitted with the original invoice for payment. Mail all invoices to: 9

10 HISD Food Services Accounting 4400 West 18 St. Houston, Texas Failure to follow the above procedure may result in cancellation of bid award. The vendor is responsible for ensuring that any subcontractor also follows the delivery procedure TITLE AND RISK OF LOSS The title and risk of loss for the requested items shall remain with the successful proposer(s) until the items have been delivered LEAD TIME Vendor shall provide lead time for all orders CONTRACT PERFORMANCE HISD reserves the right to cancel the entire contract and/or buy in the open market at the current price and charge the contractor the difference between the price so paid and the proposal price in the event (a) any item is not delivered according to the specifications and/or awarded proposal price, (b) brands of merchandise other than brand names on the proposal are delivered without prior approval, or (c) orders are not delivered within the specified time period. Vendors not in compliance with the terms and conditions set forth in this proposal project will be in default, and HISD will not place orders nor accept proposals for a period of one year CONTRACT TERM All prices, terms, and conditions agreed upon between HISD and the successful proposer(s) will be held firm for a period of one (1) year, August 1, 2013 through July 31, There is to be an additional 90-day transitional period added to the end of the contractual agreement. The contractual prices, terms and conditions are to remain in force during the transitional period FIRM PRICES All unit prices should be guaranteed for the entire proposal period. Maximum consideration will be given to these proposers. Due to system constraints pricing must be to no more than two (2) places past the decimal point. HISD reserves the right on any bids submitted where pricing is more than two (2) places past the decimal point to round the price down to two (2) places past the decimal point REFERENCES Please provide the names of at least three companies the Proposer currently provides Kitchen Equipment to, along with all of their contact information. 10

11 PAYMENT TERMS The Houston Independent School District s payment policy is payment within 30 days of receipt of delivery. The district does encourage bidders to submit preferred payment terms: however, a 2% discount is required for payment in less than 30 days from receipt of delivery. HISD still reserves the right to pay the vendor within 30 days after receipt of delivery. Equipment Testing and Approval Procedures Objective To utilize uniform criteria and procedures in evaluating, testing, and specifying Food Service Equipment. Procedure Procedures for implementation of equipment testing. All Food Services personnel shall utilize the criteria as specified in Sections I through V below, in recommending equipment for testing. I. Preliminary Review. Maintenance Supervisor/Manager will correlate equipment needs with overall food preparation and service needs. II. Requisition. Maintenance Supervisor/Manager will prepare a requisition for the equipment. III. Testing Procedure. Maintenance Supervisor/ Manager will complete appropriate report for specific types of equipment tested. IV. Performance Reports. Maintenance Supervisor/Manager will complete appropriate report for specific types of equipment tested. V. Determination of Acceptance or Rejection. A report of test results will be provided to manufacturers representative. The equipment will be purchased if approved or returned if not approved. VI. Ongoing Evaluation. I. Preliminary Review Criteria for Preliminary Equipment Review prior to approval for testing all categories of new equipment. 11

12 A. Manufacturers quality control history. B. Warranty policies. C. Delivery time. D. Dimensions. E. Energy Source. F. Availability of parts and in-service training. G. Test unit availability. H. Compliance with existing specifications. I. Food production application. J. Compliance with all applicable City of Houston codes. K. Verify availability from an approved vendor as indicated by Food Services Purchasing. L. Determine if this is a single source item. M. Identify advantages of the equipment to the District. N. Price/Cost comparison. II. Requisition The Maintenance Supervisors/Manager will prepare requisition for equipment, clearly marked as a test unit, identifying brand, model and description. III. Testing Procedure A. Prototype Testing Criteria for testing and development of prototype equipment. 1. Clearly identify product as a prototype. 2. Select a testing site based on District need and equipment function. 3. Utilize current written forms, as applicable, for evaluation. 4. Time line for testing depends on equipment function and need for design modification. B. Six Month Test Criteria utilized for six month in-school testing in selected Schools 1. Exterior and interior design. 2. Durability. 3. Ease of cleaning. 4. Mechanical design and function. 5. Performance appraisal( Does equipment meet manufacturer performance claims?) 6. Controls. 7. Response at the school kitchen level. IV. Performance Report 12

13 Procedures for completing Equipment Performance Report. A. Maintenance Supervisor/Manager completes the final performance report based on established criteria, written reports, personal observations and testing of equipment. B. Copies of all reports are filed and results added to the equipment profile data base. C. Maintenance Supervisor/Manager updates reports and modifies specifications as needed. D. A master specification manual will be maintained with cut sheets for all currently approved equipment. V. Determination of Acceptance or Rejection At the end of the test period, approved products will be purchased and rejected products shall be picked up by vendor. A report of test results will be provided to manufacturers representative by Maintenance Supervisor/Manager. VI. Ongoing Evaluation Criteria for ongoing evaluation of currently approved equipment. Completed work orders shall be used to evaluate currently approved equipment. A. Evaluate frequency and type of maintenance call to identify design or workmanship flaws as indicated by work order tracking. B. Check status of deliveries to determine if there are any problems with availability. C. Correlate equipment function with overall food preparation and service needs. 13

14 FOOD PREP EQUIPMENT VEGETABLE PRESS, MANUAL, BIPOD BASE TN-004 Vegetable press to be a manual table top style with a bipod base. The vegetable press shall be made of nickel steel with a Teflon plastic pusher and a hardened steel cutter insert. The press shall incorporate an easy change cutter insert and pusher and will accommodate any of the eight (8) cutter accessories. The accessory supplied shall be 3/8 inch cutter. Robot Coupe model RP01 or approved equal. VEGETABLE PRESS, MANUAL, WALL MOUNT TN-004A Same as TN-004, without base, wall mountable. Robot Coupe Model RP04 or approved equal. SLICERS TN knife, motor 1/2 HP, 7amps, manual reset Top mounted all metal knife sharpener 0 to 9/16" slice, Removable, easy-to-clean chute, slice deflector, knife cover and sharpener Globe 3600N n%20spec%20sheet_.pdf 14

15 FOOD PROCRSSOR TN-009 Power : 1.5 HP Single phase. 1 speed : 425 rpm. Induction motor. Magnetic safety system and motor brake. Automatic restart of the machine with the kidney shaped pusher. Delivered with : All metal vegetable prep attachment with a kidney shaped hopper (diameter 6.6") and a cylindrical hopper (diameter 2 5/16"). 2 discs included : C446SA (3mm) 1/8" slicing disc and C450GPA (3mm) 1/8" grating disc Robot Coupe CL50E or approved equal MIXER 20QT TN-010A Heavy-duty 1/2 H.P. motor Deluxe accessory packages Hobart MIXER 30QT TN-010B Heavy duty ¾ hp motor Deluxe accessory package Hobart HL300 or approved equal 15

16 MIXER 60QT TN-010C Heavy duty 2.7hp motor, Deluxe accessory package Hobart HL600 or approved equal pdf CAN OPENER, ELECTRIC TN-107 Stainless steel; casing with knife assemble, gear and shield removable without tools for easy cleaning and reassembly. NSF certified. Edlund #203 and Edlund #270 or approved equal. ult/n/0 WEDGE SECTIONIZER TN-200 Made of sturdy ABS plastic, approved by NSF International. Dishwasher safe comes with your choice of one of seven different blade cups. Sunkist model S-102 or approved equal 16

17 CAN OPENER, MANUAL TN-107A Stainless steel construction. NSF certified. Edlund S-11 or approved equal BLENDER TN-010 TN-010 Blender, 44 OZ, Toggle Switch - stainless steel container, rugged one-piece stainless steel cutting blade and die-cast black enamel base. Unique metal reinforced rubber drive coupling may be easily replaced on-site by the user.120v, UL listed Warring Model BB180S or approved equal 17

18 REFRIGERATION MILK COOLER, DOUBLE DROP FRONT (8 CASE) TN-020A 34" W x 30-1/2" D x 39-1/2" H; self contained; mechanically refrigerated; double drop front doors; interior of 18 gauge stainless steel fully welded liner with breaker strip attachment to exterior panels. Exterior and doors of 20 gauge stainless steel with magnetic gasket and stainless steel hinge. Insulation high pressure foamed in place 2" thick polyurethane. R404A refrigerant preferred, hermetically sealed unit with thermostatic adjustment with 1/3 HP motor, 120 V, 3.9 Amps, single plug. Cylinder locks provided on each top door. Rubber corner bumpers provided on each corner, heavy duty 5" stainless steel casters with brakes on two rear wheels. All stainless steel to be type 304 with number 3 finish except door contact cap which will be magnetic type 430 stainless steel, all edges smoothed and rolled, cord and plug installed. 2 year warranty parts and labor. To be UL and NSF approved. Mod-U-Serve, or approved equal. Note: Dealer must stock two (2) units at all times for immediate delivery MILK COOLER, DUAL- ACCESS TWIN TOP (12 CASE) TN-095 Unit include lids, doors, adjustable hinges, door latches and interior made from stainless steel. Floors are heavily reinforced by seam-less liner. Heavy duty, epoxy coated steel wire floor racks are provided for added floor protection. Liner bottoms to be made of 300 series stainless steel. Flexible compression gaskets ensure tight seal. All steel construction with 3-screw hinges. Self latching doors. external thermometer required. Insulation to be 1.5 to 2" thick polyurethane, CFC free. All stainless steel exterior finish and interior finish is required. Refrigerant to be 404a and CFC free, hermetically sealed unit with thermostatic adjustment with 1/3 HP motor, 115 V, 10.1 Amps, single plug, cord and plug installed for ready plug in. Cylinder locks provided on each top door. Rubber corner bumpers provided on each corner, heavy-duty 5" stainless steel casters with brakes on two rear wheels. All stainless steel to be type 300 series or better, all edges smoothed and rolled, cord and plug installed. One year warranty parts and labor. Five year warranty on the compressor. To be UL and NSF approved. Mod-U-Serve, or approved equal. 18

19 FREEZER, CHEST, 25 CU. FT. TN /4" W x 73-7/8" L x 35" H; net storage capacity of approximately 25 cu. ft.; steel cabinet with baked-on enamel finish; adjustable temperature control; hermetically sealed compressor; 115 V, 60 C, single phase; signal light; self leveling; all metal hinge construction, no plastic adjustments; interior light; tumbler lock; self-adjusting seal; defrost drain; three sliding baskets; one vertical divider; three wire cord and plug. General Electric FCM25DS or approved equal. me=311185_fcm25sb_c2.pdf FREEZER, CHEST, 20 CU. FT TN /2" W x 61-1/4" L x 35" H; net storage capacity of approximately 20 cu. ft.; steel cabinet with baked on enamel finish; adjustable temperature control; hermetically sealed compressor; 115 V, 60 C, single phase; signal light; self leveling; all metal hinge construction, no plastic adjustments; interior light; tumbler lock; self-adjusting seal; defrost drain; two sliding baskets; three wire cord and plug. General Electric FCM20DP or approved equal. me=311183_fcm20su_c2.pdf ICE CREAM FREEZER, 4 SQUARE TN-018 Cabinets to have flip lids, stainless steel top, 24 gauge steel walls, galvanized steel liner with cold wall evaporator, anti-condensate heater under stainless steel top, 2-1/4 foamed in place zero ODP urethane insulation and baked on polyester enamel finish. Standard leveling legs provided to correct for unlevel flooring. The refrigeration system will be self contained. Will be R-134A refrigerant with a temperature range from 10 degrees to -10 degrees F. Cabinets to have a standard limited 3 year extended compressor warranty and 2 year parts and labor warranty. Master-Bilt model DC-4D or approved equal. 19

20 ICE CREAM FREEZER, Two in line TN-053A Cabinets to have flip lids, stainless steel top, 24 gauge steel walls, galvanized steel liner with cold wall evaporator, anti-condensate heater under stainless steel top, 2-1/4 foamed in place zero ODP urethane insulation and baked on polyester enamel finish. Standard leveling legs provided to correct for unlevel flooring. The refrigeration system will be self contained. Will be R-134A refrigerant with a temperature range from 10 degrees to -10 degrees F. Cabinets to have a standard limited 3 year extended compressor warranty and 2 year parts and labor warranty Master-Bilt model DC-2S or approved equal. REFRIGERATOR, ONE SECTION TN-270 Reach-In Refrigerator, One Door, 24.2 cubic feet capacity; electromechanical control; 1/3 HP top mounted refrigeration system using R-134a and expansion valve metering device with easily accessible; front facing condenser coil; 115 volt with cord and plug attached. Operating temperature degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height door utilizes a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes four (4) shelves mounted on adjustable pins. Full-perimeter stainless steel thermal breaker strips with operator controllable door perimeter heaters. Load- Sure guard protects against improper loading. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty, with an additional Two Year Parts Warranty on the compressor. Traulsen model RHT132WUT-FHS. utma= & utmb= & utmc= & utmx= & utmz= utmcsr=yahoo utmccn=(organic) utmcmd=organic utmctr =Traulsen& utmv=-& utmk=

21 REFRIGERATOR, ONE SECTION TN-270PT Pass-Thru Refrigerator, Two Doors (one front & back), 25.2 cubic feet capacity; electromechanical control; 1/3 HP top mounted refrigeration system using R-134a and expansion valve metering device with easily accessible; front facing condenser coil; 115 volt with cord and plug attached. Operating temperature degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes thirteen (13) universal tray slides. Full-perimeter stainless steel thermal breaker strips with operator controllable door perimeter heaters. Load-Sure guard protects against improper loading. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty, with an additional Two Year Parts Warranty on the compressor. Traulsen model RHT132WPUT-FHS. utma= & utmb= & utmc= & utmx= & utmz= utmcsr=yahoo utmccn=(organic) utmcmd=organic utmctr =Traulsen& utmv=-& utmk= REFRIGERATOR, ONE DOOR TN-270A Refrigerator, One Door, 30 wide x 34-1/2 deep x 84 high, 24cu.ft. capacity. 1/4hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. 1 year parts and labor warranty and 5 years on compressor. Utility model R-30-SS-1S-D, or approved equal. Utility preferred on new construction 21

22 REFRIGERATOR, ONE DOOR PASS THRU TN-270A /PT Spec. same as TN-270A except Pass Thru Model # R-30-SS-1S-D-PT REFRIGERATOR, TWO SECTION TN-280 Reach-In Refrigerator, Two Doors, 51.6 cubic feet capacity; electromechanical control; 5/8 HP top mounted refrigeration system using R-134a and expansion valve metering device with easily accessible; front facing condenser coil; 115 volt with cord and plug attached. Operating temperature degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes eight (8) shelves (4 per section) mounted on adjustable pins. Fullperimeter stainless steel thermal breaker strips with operator controllable door perimeter heaters. Load-Sure guard protects against improper loading. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty, with an additional Two Year Parts Warranty on the compressor. Traulsen model RHT232WUT-FHS. utma= & utmb= & utmc= & utmx= & utmz= utmcsr=yahoo utmccn=(organic) utmcmd=organic utmctr =Traulsen& utmv=-& utmk=

23 REFRIGERATOR, TWO SECTION TN-280PT Pass-Thru Refrigerator, Four Doors (two front & back), 54.2 cubic feet capacity; electromechanical control; 5/8 HP top mounted refrigeration system using R-134a and expansion valve metering device with easily accessible; front facing condenser coil; 115 volt with cord and plug attached. Operating temperature degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes twenty-six (26) universal tray slides (13 per section). Full-perimeter stainless steel thermal breaker strips with operator controllable door perimeter heaters. Load-Sure guard protects against improper loading. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty, with an additional Two Year Parts Warranty on the compressor. Traulsen model RHT232WPUT- FHS. utma= & utmb= & utmc= & utmx= & utmz= utmcsr=yahoo utmccn=(organic) utmcmd=organic utmctr =Traulsen& utmv=-& utmk= REFRIGERATOR, TWO DOOR TN-280A Refrigerator, Two Door, 60 wide x 34-1/2 deep x 84 high, 53.4cu.ft. Capacity. 1/2hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. (1) year parts and labor warranty and (5) years on compressor. Utility model R-60-SS2S-D. Utility preferred on new construction 23

24 REFRIGERATOR, TWO DOOR PASS THRU TN-280A/PT Spec same as TN-280A except Pass Thru Model # R-60-SS2S-D-PT REFRIGERATOR, THREE SECTION TN-290 Reach-In Refrigerator, Three Doors, 79.0 cubic feet capacity; electromechanical control; 3/4 HP top mounted refrigeration system using R-134a and expansion valve metering device with easily accessible; front facing condenser coil; 115 volt with cord and plug attached. Operating temperature degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes twelve (12) shelves (4 per section) mounted on adjustable pins. Full-perimeter stainless steel thermal breaker strips with operator controllable door perimeter heaters. Load-Sure guard protects against improper loading. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty, with an additional Two Year Parts Warranty on the compressor. Traulsen model RHT332WUT-FHS. utma= & utmb= & utmc= & utmx= & utmz= utmcsr=yahoo utmccn=(organic) utmcmd=organic utmctr =Traulsen& utmv=-& utmk=

25 REFRIGERATOR, THREE DOOR TN-290A Refrigerator, Three Door, 90 wide x 34-1/2 deep x 84 high, 84cu.ft. capacity. 1/2hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. (1) year parts and labor warranty and (5) years on compressor. Utility model R-90-SS-3S-D. Utility preferred on new construction FREEZER, ONE SECTION TN-300 Reach-In Freezer, One Door, 24.2 cubic feet capacity; electromechanical control; 1/2 HP top mounted refrigeration system using R-404A and expansion valve metering device with easily accessible; front facing condenser coil; 115 volt with cord and plug attached. Operating temperature 0 to -5 degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height door utilizes a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes four (4) shelves mounted on adjustable pins. Full-perimeter stainless steel thermal breaker strips with operator controllable door perimeter heaters. Load-Sure guard protects against improper loading. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty, with an additional Two Year Parts Warranty on the compressor. Traulsen model RLT132WUT-FHS. utma= & utmb= & utmc= & utmx= & utmz= utmcsr=yahoo utmccn=(organic) utmcmd=organic utmctr =Traulsen& utmv=-& utmk=

26 FREEZER, ONE DOOR TN-300A Freezer, One Door, 30 wide x 34-1/2 deep x 84 high, 24cu.ft. capacity. 1/2hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. Defrost shall be automatic, time initiated, and temperature terminated. Defrost system shall be equipped with distinct termination and safety switches. 1 year parts and labor warranty and 5 years on compressor. Utility model F-30-SS-1S-D or approved equal Utility preferred on new construction FREEZER, TWO SECTION TN-310 Reach-In Freezer, Two Door, 51.6 cubic feet capacity; electromechanical control; 3/4 HP top mounted refrigeration system using R-404A and expansion valve metering device with easily accessible; front facing condenser coil; 115 volt with cord and plug attached. Operating temperature 0 to -5 degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a selfclosing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes eight (8) shelves (4 per section) mounted on adjustable pins. Full-perimeter stainless steel thermal breaker strips with operator controllable door perimeter heaters. Load-Sure guard protects against improper loading. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty, with an additional Two Year Parts Warranty on the compressor. Traulsen model RLT232WUT-FHS. utma= & utmb= & utmc= & utmx= & utmz= utmcsr=yahoo utmccn=(organic) utmcmd=organic utmctr =Traulsen& utmv=-& utmk=

27 FREEZER, TWO DOOR TN-310A Freezer, Two Door, 60 wide x 34-1/2 deep x 86 high, 54cu.ft. capacity. 3/4hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. Defrost shall be automatic, time initiated, and temperature terminated. Defrost system shall be equipped with distinct termination and safety switches. 1 year parts and labor warranty and 5 years on compressor. Utility model F-60-SS-1S-D or approved equal. Utility preferred on new construction FREEZER, THREE SECTION TN-320 Reach-In Freezer, Three Door, 79.0 cubic feet capacity; electromechanical control; 3/4 HP top mounted refrigeration system using R-404A and expansion valve metering device with easily accessible; front facing condenser coil; 208/115 volt with cord and plug attached. Operating temperature 0 to -5 degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes twelve (12) shelves (4 per section) mounted on adjustable pins. Full-perimeter stainless steel thermal breaker strips with operator controllable door perimeter heaters. Load-Sure guard protects against improper loading. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty, with an additional Two Year Parts Warranty on the compressor. Traulsen model RLT332WUT-FHS. utma= & utmb= & utmc= & utmx= & utmz= utmcsr=yahoo utmccn=(organic) utmcmd=organic utmctr =Traulsen& utmv=-& utmk=

28 FREEZER, THREE DOOR TN-320A Freezer, Three Door, 90 wide x 34-1/2 deep x 86 high, 84cu.ft. capacity. 1hp compressor; 115/208/230 volt with no cord and plug attached. Stainless steel front, sides and interior. Door shall be selfclosing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. Defrost shall be automatic, time initiated, and temperature terminated. Defrost system shall be equipped with distinct termination and safety switches. (1) year parts and labor warranty and (5) years on compressor. Utility model F-90-SS-1S-D or approved equal. Utility preferred on new construction ICE MACHINE, 300 LB. PRODUCTION TN-550 Ice Machine, having ARI-certified ice production capacity of 300 lbs. per 24 hours at 90ºF air temperature, with half dice cube size: 3/8" x 1-1/8" x 7/8," ice thickness control that assures uniform cube size without using pressure controls or thermostats, type R-404A refrigerant, exterior to be of type 304 stainless steel, 115 volt, 60 cycle, 1 phase, automatic built in self cleaning system with choice of cycle from two, four, or twelve week duration, self contained operation, three years parts and labor warranty, five years parts and labor on evaporator, and (5) year parts and (3) years labor on compressor. Manitowoc model IY0304A or approved equal. Note: Bin and Machine must come from the same vendor. 28

29 ICE MACHINE, 500 LB. PRODUCTION TN-555 Ice Machine, having ARI-certified ice production capacity of 500 lbs. per 24 hours at 90ºF air temperature, with half dice cube size: 3/8" x 1-1/8" x 7/8," ice thickness control that assures uniform cube size without using pressure controls or thermostats, type R-404A refrigerant, exterior to be of type 304 stainless steel, 115 volt, 60 cycle, 1 phase, automatic built in self cleaning system with choice of cycle from two, four, or twelve week duration, choice of either self contained or remote condenser at time of order, three years parts and labor warranty, (5) years parts and labor on evaporator, and (5) year parts and (3) years labor on compressor. Manitowoc model IY0504A or approved equal. Note: Bin and Machine must come from the same vendor. ICE STORAGE BIN TN-589 Ice Storage Bin, foamed in place urethane insulation, lined with either stainless steel or one piece polyethylene, exterior top, front, sides, and doors shall be polished stainless steel, mounted on 6 inch adjustable legs. Specify ARI rated capacity of 100% fill of 200, 300, 400, 600, 800, 1,000, 1,300, 1,600, 2,000, or 2,600 pounds at time of order. Manitowoc or approved equal Note: Bin and Machine must come from the same vendor. 29

30 WALK-IN COOLER/FREEZER SPECIFICATIONS WALK-IN COOLER/FREEZER SPECIFICATIONS TN PANEL FABRICATION All panels shall consist of metal pans formed to precise dimensions. Insulation shall be foamed in place urethane foam bonded permanently to the complete inner surfaces of both interior and exterior metal pans to form a strong rigid unit. Panels shall not have internal wood or metal support, framing straps, or other non-insulating members. Each panel shall be 100% urethane foam insulation exclusive of metal pans. Perimeter structure shall be formed of high density urethane insulation forming tongues and grooves to assure vapor proof and airtight joints and prevent pre-installation damage and deterioration of low-density urethane. NSF approved double-bead vinyl gaskets shall be applied to the tongue side of all panels on both interior and exterior. Gaskets shall be impervious to stains, grease, oils, mildew, etc. Assembly of the walk in shall be accomplished by cam action hook arm assembly set in the matching panel. Rotation of the cam action hook arm shall pull and lock panels together to form airtight, vapor proof joints. Rotation of the cam locks shall be operated from inside the walk in through access ports that are sealed with vinyl snap in closures. 2. INSULATION - UNDERWRITERS LABORATORY LISTED. Insulation shall be 4 or 5 thick rigid zero ozone depleting HFC 134a blown Class I urethane foam classified according to UL723 (ASTM-E-84) as tested by Underwriters Laboratories. The urethane foam shall be foamed in place to bond to inner surfaces of metal pans having an average thermal conductivity (K factor) of 0.13 BTU/hr/sq.ft. per degrees/fahrenheit/inch. Panels shall bear a certifying Underwriters Laboratories, Inc. label. 3. SURFACE FINISHES Panel finishes shall be constructed of.040 stucco embossed aluminum on the exterior and interior or 20ga smooth stainless. Where applicable, floor shall be buried in a recessed pit with a quarry tile finish for new construction. Other floors shall be 3/16 diamond aluminum tread plate 6061 with welded seams to withstand uniformly distributed loads to 1200 pounds per square foot. Non skid strips shall be installed on all floors. Entrance doors, interior and exterior, shall be at least 22 gauge, type 304, #3 finish stainless steel. 30

31 5. ENTRANCE DOOR AND DOOR PANEL Each walk in will be fitted with on standard 34 W x 78 H hinged type flush mounted entrance door bearing the UL seal of approval. A. Door shall be equipped with magnetic gasket. B. A positive hydraulic door closure and latch to open door by breaking magnetic force of gasket. C. Hardware with provisions for locking. D. Safety release which prevents entrapment. E. Door shall be self-closing with strap-type, cam-lift hinges and positive hydraulic door closure. F. Door jamb shall be made of heavy "U" channel type, reinforced steel frame of not less than 14 gauge thickness around entire perimeter with thermal break. G. An isolated, low wattage heater strip covered by magnetically attracting stainless steel shall be fitted onto this jamb. This strip shall provide perfect sealing of magnetic gasket and prevent frost and condensation build up. Heat strip to be in door and frame. H. Each door section shall be provided with an incandescent type vapor proof light, with pilot light switch, wire guard and rigid conduit between switch box and outlet. I. A heavy gauge threshold with non-skid stripping shall be provided with each door section. J. A 2-1/2" diameter chrome plated NSF listed thermometer shall be included with each door section. K. No visual observation window 6. LIGHTING: Additional protected incandescent fixtures with compact fluorescent lighting to provide 20 ft. candles of light to all areas. 7. NSF RATED Walk-in shall be fabricated to comply with National Sanitation Foundation Standard No. 7 and carry the NSF Label. 8. REFRIGERATION SYSTEMS: Refrigerant shall be R-404A on all coolers. Temperature on all coolers shall be +35 F. Refrigerant shall be R-404A on all freezers. Temperature on freezers shall be -10 F. Copeland hermetic compressors (no substitute). Evaporators to be matched with condensing unit BTU output at the desired temperature setting. Condensing units shall be factory assembled and UL listed. Fan motors, guards, multi-fin and tube type coil shall be housed in heavy gauge aluminum housing. Unit shall have a drain pan with suitable drain pipe connection. Freeze evaporators shall have an automatic electric defrost system including heaters(no internal coil heaters), time clock, fan delay control, heated drain pan and heated drain pipe. Defrost shall be time initiated and terminated with built in safe control. All evaporators shall be UL listed.electrical specifications will be provided for each project. 31

32 9. ONE OF THE FOLLOWING SYSTEMS SHALL BE SUPPLIED AS THE INDIVIDUAL JOB SPECIFICATION WILL CALL FOR: A. REMOTE SYSTEMS Systems supplied with necessary major parts for field installation by refrigeration, plumbing, and electrical contractors. Remote parts will include condensing unit, evaporator, controls, expansion valve, dryer, sight glass, vibration eliminator, evaporator mounting kit and condenser mounting brackets or rack. No peanut switches. Service valve on receiver should read line pressure when closed. B. PREASSEMBLED REMOTE SYSTEMS Same components as outlined in paragraph A., with all parts mounted. This system will be designed to reduce field labor and will require only tubing and electrical hook-up supplied by refrigeration and electrical contractors. C. TOP-MOUNTED OR SIDE-MOUNTED SELF- CONTAINED FACTORY ASSEMBLED SYSTEMS Same components as outlined in paragraph A., requiring only electrical connection and drain lines by contractors. System shall have quick disconnect precharged lines for easy, economical installation. D. MODERATE LOW AMBIENT KITS WITH PUMP DOWN Outdoor condensing units must include pressure control to govern condenser fan operation, crankcase heater, temperature control, solenoid valve for pump down and rain proof housing. High pressure control. No headmasters. E. COMPRESSORS SHALL HAVE A (5) YEAR LIMITED WARRANTY F. INSTALLING CONTRACTOR 1. Shall comply with local codes and take out necessary permits. 2. Provides start up. 3. One year free labor on complete walk-in and refrigeration system. G. SUCCESSFUL BIDDER Shall be held responsible for compressor replacements as needed during the entire five years. H. EQUIPMENT REQUIREMENT Condensers, (RDT) Thermo Kool panels or Kolpak panels. Copeland compressors and low profile Bohn evaporators or approved equals. These are specified to establish a quality standard. Any alternates must be prequalified and approved, with engineering data and samples submitted to the Food Services Department ten (10) days prior to bid opening. Any changes in general construction due to an alternate will be at the sole cost of the installing contractor. 32

33 Note: Refer to TN-78C Shelving (Vented) for the specification of the shelving to be furnished in both walk-in refrigerators and walk-in freezers. All new Walk-in shall comply with the Federal Energy Independence and security Act of 2009 WALK-IN COOLER/FREEZER SPECIFICATIONS, SELF CONTAINED TN-078SC 1. GENERAL The walk -in shall be factory prefabricated and of unitized design specifically constructed for outdoor use. The walk -in will allow installation without assembly and relocation without disassembly. The walk - in shall require an onsite contractor responsible for the pouring of a concrete pad, connection of electrical power supply to each refrigeration system and for flashing the walk - in to the building wall. The walk -in shall bear the label of the following National Certification Agencies: National Sanitation Foundation (NSF Standard #7) Underwriters Laboratories (Major Refrigeration Components) Underwriters Laboratories (Major Electrical Components) Underwriters Laboratories (Class I Urethane) The walk -in shall comply with the following model building codes: International Conference of Building Officials Southern Building Code Congress International Building Officials Congress Association National Electric Code 2. SIZE AND CAPACITY The walk - in shall be built to specified interior and exterior dimensions as shown on the plans or drawings. The walk - in shall have sufficient refrigeration to maintain (+ 35 F, or, -10 F) temperature inside the compartment when the ambient temperature is 100 F, the average number of door openings is four per hour, and there is no heat load from warm products entering unit. The refrigeration system shall be wired to run on VAC 60 Hz / 3 Phase) power. 3. STRUCTURE The walk -in structure shall be constructed with an embossed aluminum interior and exterior and a 4" urethane core. All doors opening into a controlled temperature room shall be supplied with door frame heaters which shall supply sufficient heat to prevent condensation or frost accumulation. Door jamb flashing shall be stainless steel. Doors shall be provided with a magnetic gasket around the perimeter. Flush bottom doors shall be provided with an adjustable vinyl sweep gasket. When door is closed it shall form a positive airtight seal. Door gaskets shall be installed in retainers for easy replacement. Doors shall incorporate a positive snap action latch with adjustable strike. The latch shall be equipped with a cylinder lock and OSHA approved inside safety release mechanism to prevent entrapment. The hardware shall be chrome finished and mounted with stainless steel tamper proof screws. Doors shall be equipped with heavy duty strap type door hinges. They shall be cam lift type, self closing with nylon bearings and door lift off 33

34 capability. Hardware shall be chrome finished and mounted with stainless steel tamper proof screws. Doors shall be hinged and sized as shown on plans or drawings. 4. THERMOMETER A 2" flush face dial type thermometer will be mounted adjacent to entry door. Thermometer shall be NSF approved. 5. SELF CONTAINED REFRIGERATION SYSTEM Packaged refrigeration system shall be factory installed by the walk - in manufacturer. Systems shall be complete and ready to operate without field assembly, installation or start up. Refrigerants shall be non-flammable type R404A. Electrical controls including circuit breakers shall be supplied, installed and ready to operate with single point electrical connection by others. Refrigeration system shall be roof mounted. Refrigeration systems shall be factory tested for a minimum of 24 hours prior to shipment.partition walls shall be constructed in the same manner as the exterior walls with a 4" urethane core. 6. FLOOR A 4" insulated (R-32) prefabricated floor shall be supplied and bonded to the walls. The floor shall be reinforced 3/16 diamond floor plate with welded seams. The floor shall be constructed for permanent elevation 1-1/2" above grade. The elevation provides for air circulation under the floor to eliminate corrosion and the need for an insulated and/or ventilated slab. A welded, heavy duty steel frame shall be encased in aluminum and permanently bonded to the floor to ensure total portability without damage to the walk - in. The floor shall have the capacity to support 1200 lbs/sq. ft. of evenly distributed load. 7. INSULATION All insulation shall be a minimum of 4" thick rigid urethane foam chemically bonded to the interior and exterior walls to form a one piece structure. The thermal conductivity (k) of 0.13 BTU/hr./sq.ft. per degrees/fahrenheit/in. 8. LIGHTING Walk - in shall be complete with incandescent light fixtures with compact fluorescent bulbs factory installed and tested for proper operation prior to shipment. An incandescent light switch shall be mounted adjacent to entry door and incorporate a visible pilot light to indicate when lights are in the on position. 9. DOORS Doors shall be constructed in the same manner as the walls with no less than 4" urethane insulation. All new Walk-in shall comply with the Federal Energy Independence and Security Act of

35 TRANSPORT AND STORAGE CART, DISH, POLYETHYLENE TN /2 " W x 37-1/4" L x 34-5/8" H; three molded polyethylene shelves, 31-1/2 " x 30-5/8" with clearance of 11-3/8" between shelves; two (2) five inch swivel castors; two (2) five inch fixed castors with one brake; 800 pound carrying capacity. Specify color at time of order. Cambro BC 235 or approved equal CART, DISH, STAINLESS STEEL TN-003 Unit shall be of fully welded unitized construction with an overall carrying capacity of 500 pounds. Corner legs shall be of 16-gauge angle stainless steel. Shelves shall be of 20-gauge stainless steel with long shelf edges double hemmed for extra strength, and shall be electronically spot welded to upright legs at all points. Unit shall have a stainless steel push handle welded to frame, and shall have corner bumpers mounted to front legs and ends of push handle. Four each 4 swivel casters shall be mounted to the dolly frame. Lakeside model 442 or approved equal DOLLY, MILK CASE TN " L x 13-3/4" W, with 3" heavy duty castors; one piece angle frame construction; to accommodate two (2) 13" x 13" milk crates. Cambro model CD1327 or approved equal. 35

36 ULTRA PAN CARRIERS TN-123 Cabinet to transport or store either hot or cold foods; one piece, polyethylene shell filled with thick foam insulation; nylon latch and air-tight gasket; twelve (12) molded-in rails on 1½" centers; door to open 270º; two units are to interlock for stacking or transporting. Overall dimensions 25- ¾" X 18-¼" X 24-7/8"; Optional dolly to be available and optional strap to secure two (2) cabinets to be available. Optional Items: Cambro UPC400 or approved equal. CAMDOLLY STRAP TN-123AB Cart for TN-123 Cambro Model 400STP Camcarts, for Food boxes and Trays/sheet pans TN-123A Use to hold hot or cold bulk food stored on trays, sheet pans or in food boxes. Durable polyethylene and thick foam insulation retain safe food temperatures. Sturdy plastic, rustproof latches are secured into molded-in mounting plates. Molded-in handle on the back for easy maneuvering. All carts have 6" (15,2 cm) casters: 2 front fixed, 2 rear swivel, 1 with brake. Cambro model 1826DTC or approval equal 36

37 RACK, BUN TN-065 Stainless steel upright and ledges; All welded stainless steel construction No pry points. Easy to clean and sanitize, simply wipe down or steam clean. NSF listed Lakeside m/n 139 S/S approved equal SHELVING, SOLID TN-O78A Posts and longitudinal beams to be constructed of a pultrusion of continuous glass fibers and thermoset resin composite, exterior surfaces are high impact thermoplastic resin; shelves to be constructed of high impact polymer, removable, commercial dishwasher safe. Load capacity of 800 pounds up to 54". Sizes Metromax or approved equal Note: Shelving, Solid and Post should have the same vendor. SHELVING, VENTED TN-078C Same specification as TN-78A except individual shelves are vented. Note: Shelving, Vented and Post should have the same vendor Metro-max or approved equal Note: Shelving, Solid and Post should have the same vendor. 37

38 DUNNAGE RACK TN-078B Same specification as TN-78A, but with vented shelf and 8" posts. Sizes 18" x 36", 18" x 48", and 24" x 48". Metro-max or approved equal. Note: Shelving, Solid and Post should have the same vendor. SHELVING STARTER UNITS (SOLID AND VENTED) TN -592 Sizes: 12" x 24", 12" x 36", 12" x 42", 12" x 48", 12" x 54",18" x 24", 18" x 36", 18" x 42", 18" x 48", 18" x 54", 24" x 24", 24" x 36", 24" x 42", and 24" x 48", 24" x 54". Made of smooth polypropylene, rust proof, traverses and posts are weight bearing with solid, steel cores; Antimicrobial. Cambro or approved equal. Note: Shelving, Solid and Post should have the same vendor. SHELVING ADD-ON KITS (SOLID AND VENTED) TN-592A Sizes 18" x 36", 18" x 48", and 24" x 48". Made of smooth polypropylene rust proof. Traverses and posts are weight bearing with solid, steel cores; Antimicrobial. Cambro or approved equal. Note: Shelving, Solid and Post should have the same vendor. COMBINATION SAFE TN-600 EXTERIOR 13.7in H x 16.3in W x 19.3in D INTERIOR 9.6in H x 12.6in W x 11.5in D CAPACITY.8ft Key rack and compartment for small items Multiposition tray holds standard and A-4 size papers, folders and binders Metal handle may be bolted to floor (hardware included) 3-number combination lock with clicking dial and tubular key lock 4 live-locking bolts ETL Verified 1-hour fire protection for CDs, DVDs, USB drives and memory sticks up to 1700 F/927C to protect precious media in the event of a fire ETL verified 15 ft. Drop Test UL Classified 1-hour proven fire protection Sentry model OS0401 or approval equal 38

39 COOKING APPLIANCES OVEN, GAS, DOUBLE CONVECTION WITH PLAIN DOORS TN-041A Stainless steel exterior, including stainless steel louvered back panel. Baking compartment, including baffle, to be porcelain enameled steel. Top, back, and sides to be insulated with 1" high temperature mineral fiber sheet. Solid stainless steel doors to have a single handle mounted on left hand door to operate both doors simultaneously to sides, to a total opening of 140 on a horizontal plane. Rack supports shall be chrome plated steel, capable of holding a total of eleven (11) oven racks with a minimum spacing of 1-5/8" O.C. To be furnished with five (5) standard racks (each section). Oven to be heated both directly and indirectly, due to the recirculation of the heated gases. The thermostat shall be electric, direct acting, with a temperature range of 200 F. (93 C.) to 500 F. (260 C.). Thermostat shall control the gas by means of a solenoid valve. Ovens to be equipped with an infinite setting solid state thermostat consisting of a solid state control board with a thermistor sensor probe. Oven constructed with entire control panel to slide out from front, to provide easy access to all controls, gas pressure regulator and gas cut-off valve. There shall be no exposed screws or bolts on oven exterior. The interior of oven cavity shall be clear without exposed ducts or stand pipe. Oven to be equipped with solid state ignition system. (60) minute mechanical timer with electric buzzer as standard Blodgett DFG-100 or approved equal RANGE, GRATE TOP TN-097 Two burner 34,000 BTU, grate top range with cabinet base, front, both sides, and rear of stainless steel with chrome legs. Stainless steel flue riser with no overhead shelf. Gas supply should be front or rear hook up. Southbend # P16, approved equal. 39

40 RANGE, GRATE TOP WITH CONVECTION OVEN TN " wide sectional range with four open-top burners available with a standard-oven base, convection-oven base, cabinet base, or as a modular unit (for mounting on countertop, refrigerated or freezer base) Four Signature Pyromax 45,000 BTU NAT (42,000 BTU LP) patented clog-free burners Removable, welded steel top grates 9-1/4" deep front rail Removable drip tray Stainless steel front, sides, rear and exterior bottom Fully insulated lining and burner box 1-1/4" front gas manifold and 1" rear gas connection 5" high stainless steel flue riser Oven racks (2 for standard oven, 3 for convection oven) sheet pans to fit either way Convection-oven models have 1/2 hp, two-speed blower Southbend Model P32A-XX Platinum Series, or approved equal TWO COMPARTMENT FORCED CONVECTION STEAMER ON 24 INCH CABINET BASE TN-106 Two compartment convection steamer on a 24" wide cabinet base. Each compartment supplied with four convection generators producing turbulent steam at atmospheric pressure. Compartments to be stainless steel with removable stainless steel wire racks to accommodate standard cafeteria pans. Control panel to operate in timed or manual mode. Mechanical timer from 0 to 60 minutes. Unit equipped with steam purifier, continuous venting vacuum exhaust, steam condenser, pressure switch, automatic safety valve and stainless steel drain screen. Exterior to be stainless steel #4 finish, equipped with two piece air insulated stainless steel doors. Doors may be opened or closed at any time without interruption of cooking cycle. Gas steam generator shall be copper jet tube type, ASME, N.B., and A.G.A. listed with a maximum of 200,000 BTU input. Steam generator, boiler, to be nickel plated. To have visual water level gauge, 115 V control for water level, low water cut off and adjustable pressure switches. Boiler equipped with automatic blow down at shut off including a built in power flush system to assure evacuation of drain valve. Boiler to have secondary low water cut off (as per California code). Unit to require one water connection. Two (2) year warranty, parts and labor. Cleveland model 24-CGM 200 or approved equal. m% pdf 40

41 STEAMER WITHOUT BOILER TN-590 Fast cook times with Steam Vector Technology Steam Vector utilizes no moving parts simple water and drain connection no water filtration or treatment required super duty heater configuration operating instructions on door in English and Spanish NSF listed, variable temperature hold mode Door can be opened at any time during cooking cycle Steamer cavity made of durable reinforced 14 ga. 304 stainless steel 5 power cord with plug included Front mounted drain valve Easy to use digital controls cook and hold modes low water, high water and oven temp indicator lights field reversible, slam able door 208 volt Accutemp E6 or approved equal STAND FOR TN-590 STEAMER TN-590A Stainless steel floor stand that will accommodate either one or two steamer w/adjustable bullet feet. Must be UL and NSF listed CABINET, HOT PASS THRU, SUPER BAR TN " W x 30-1/2" D x 67-1/2" H; stainless steel interior and exterior; low heat density output thermal cable; manually adjustable thermostat. All castors should be stainless steel. ; 120 V, 60 C, single phase; 2000 watts; 16.7 amps; three wire cord and plug. One (1) year parts and labor warranty. Alto-Shaam 1000-UPS, Utility or approved equal. UP_1112.pdf 41

42 CABINET, HOT, SUPER BAR TN " W x 29-1/2" D x 67-1/2" H; stainless steel interior and exterior; low heat density output thermal cable; manually adjustable thermostat; 120 V, 60 C, single phase; 2000 watts, 16.7 amps; (3) wire cord and plug. All castors should be stainless steel. One (1) year parts and labor warranty. Alto-Shaam 1000-UP, Utility or approved equal. UP_1112.pdf Two Sided Grill TN-595 Heavy-duty cast iron platens, available in grooved or smooth, provide Thermostat is rated from 175 F (79 C) to 450 F (232 C) embedded elements in cast iron platens, reliable hinge system for even pressure on both sides of product for consistent heat and searing of product. Grilling height accommodates products up to three inches the bottom platen has a patented 3/4 splash guard corrals product. Removable grease trough located in front of bottom platen allows easy clean up. Star Model GX20IG or approved equal ROUND COOKER WARMER TN qt. (RCW-7) or 11 qt. (RCW-11) capacity. Stainless steel housing with stainless steel liner. Thermostatic control raised liner edge (marine lip) prevents outside condensation electric low watt density element provides fast, even heat. Wet or dry operation Uses standard insets and covers (not included) 42

43 HOT FOOD HOLDING CABINET, ONE SECTION TN-410 Reach-In Hot Food Holding Cabinet, One Door, 24.8 cubic feet capacity; electromechanical control; fan assisted air distribution system with tubular heating element. 208/115 volt with cord and plug attached. Operating temperature adjustable from degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height door utilizes a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes four (4) shelves mounted on pilasters. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty. Traulsen model RHF132W-FHS. HOT FOOD HOLDING CABINET, ONE SECTION TN-410PT Pass-Thru Hot Food Holding Cabinet, Two Doors (one front & back), 26.1 cubic feet capacity; electromechanical control; fan assisted air distribution system with tubular heating element. 208/115 volt with cord and plug attached. Operating temperature adjustable from degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes thirteen (13) universal tray slides. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty. Traulsen model RHF132WP-FHS. HOT FOOD HOLDING CABINET, TWO SECTION TN-420 Reach-In Hot Food Holding Cabinet, Two Door, 52.8 cubic feet capacity; electromechanical control; fan assisted air distribution system with tubular heating element. 208/115 volt. Operating temperature adjustable from degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes eight (8) shelves (4 per section) mounted on pilasters. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty. Traulsen model RHF232W-FHS. 43

44 HOT FOOD HOLDING CABINET, TWO SECTION TN-420PT Pass-Thru Hot Food Holding Cabinet, Four Doors (two front & back), 55.8 cubic feet capacity; electromechanical control; fan assisted air distribution system with tubular heating element. 208/115 volt. Operating temperature adjustable from degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes twenty-six (26) universal tray slides (13 per section). Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty. Traulsen model RHF232WP-FHS. HOT FOOD HOLDING CABINET, THREE SECTION TN-430 Reach-In Hot Food Holding Cabinet, Three Door, 79.0 cubic feet capacity; electromechanical control; fan assisted air distribution system with tubular heating element. 208/115 volt. Operating temperature adjustable from degrees F. All metal construction; interior and exterior stainless steel. Cabinet and door are built using at least 2 depth; 100% foamed in place CFC-Free insulation. Full height doors utilize a self-closing cam-lift hinge with stay open feature. Lights are automatically operated using a switch built into the hinge for protection. Interior includes twelve (12) shelves (4 per section) mounted on pilasters. Cabinet is supported on 6 high casters, is UL & NSL approved, and covered by a Three Year Parts & labor Warranty. Traulsen model RHF332W-FHS. 44

45 SANITATION WASHER, CLOTHES TN-007 Top loading; 18 pound capacity; approximately 27" W x 25" D x 43-1/2" H; porcelain cabinet and tub; single speed; three wash cycles; three water level selections; three wash/rinse temperature combinations; damp dry spin at approximately 600 rpm; unbalance load control; permanent lubrication on all friction parts; 115 V, 60 C, single phase; 8 amp; standard plug to meet City of Houston Building Code; 1/2 HP motor with overload protector and automatic reset; white only. One (1) year parts and labor warranty. General Electric WWA GWH, Roper RAX6144E or approved equal. DRYER, CLOTHES TN-007A Approximately 27" W x 25" D x 43 1/2" H; Standard capacity; porcelain top and drum, other areas of acrylic enamel or porcelain; 1/4 HP motor; permanently lubricated overload protector and automatic reset; four drying temperature selections. 120/240 V, 60 C, single phase; 5000 watts; wiring connection for 30 amp, three (3) wire circuit to meet City of Houston code requirements, six (6) foot cord to be supplied. White only. One (1) year parts and labor warranty. General Electric DDE-5808M, Roper REX4635E or approved equal. WASHER/DRYER, STACKABLE TN-007B Approximately 34-5/8" H x 27" D x 27" W; Washer 120 V, 60 C, single phase; Dryer - 120/230 V, 60 C, single phase, six (6) foot cord to be supplied. White only. One (1) year parts and labor warranty. Gibson Stackmasters, Washer model WS27M6WT, Dryer model DE27S6WT; Whirlpool model GTE6234 or approved equal. 45

46 DISPOSER (2 HP) TN-037 Water-cooled, totally enclosed 2 HP motor protected by air seal; 115 V, 60 C, single phase or 208/240 V, 60 C, single or three phase; 8" shredder of precision ground steel; 8" rotor of wear resistant, hardened carbide material; molded mounting collar with stainless steel clamps; paint free, heat treated corrosion resistant alloy housing; adapter ring and leg support. One (1) year parts and labor warranty. Salvajor II Model 200 or approved equal. Note: Dealer must stock all voltages for immediate delivery. Refer to TN-45 & 46 Dishwashing assembly to locate installation DISPOSER (1 HP) TN-037A Water cooled, totally enclosed 1 HP motor protected by air seal; 115 V, 60 C, single phase or 208/240 V, 60 C, single or three phase; 8" shredder of precision ground steel; 8" rotor of wear resistant, hardened carbide material; molded mounting collar with stainless steel clamps; paint free, heat treated corrosion resistant alloy housing; adapter ring and leg support. One (1) year parts and labor warranty. Salvajor II Model 100 or approved equal. Note: Dealer must stock all voltages for immediate delivery. WATER HEATER TN-102 up to 96% Meets ASHRAE/IESNA standards for standby loss and recovery efficiency Low-NOx emissions - comply with SCAQMD Rule Sealed power direct-vent, sidewall or vertical, draws all combustion air from outside Combustion air blower, all controls and gas valves located on top of unit for protection against high water ASME tank (3)-year limited tank warranty State SUF or approval equal 46

47 Table and Sinks TABLE, WORK (4') TN " L x 30" W x 34" H; 14 gauge stainless steel top and under shelf; legs, drawer, and adjustable bullet feet of stainless steel. Under shelf must have 12-gauge stainless steel channel support underneath and to be welded and polished to each leg at 8" from floor. Must comply with all applicable NSF standards. TABLE, COOK WITH POT RACK AND SINK (10') TN-022 Rack height 7' 2"; stainless steel adjustable bullet feet; table 30" W x 120" L x 34" H; top of 14 gauge polished stainless steel, 1-1/2" rolled down edges, reinforced with 12 gauge steel channels; full length double bar pot rack over table, supported by capped 1-5/8" O.D. 16 gauge stainless steel pipe standards extending through stainless steel conical gussets, continuously welded, ground and polished to table top and back between table legs; bars of 1/4" x 2" flat bar stainless steel with semi circular ends and 36 fitted removable double prong pot hooks;14 gauge stainless steel undershelf with easily removable sections; two (2) 15" x 20" x 5" drawers; swing spout, faucet and basket strainer for a 15" x 20" x 8" stainless steel sink on right end. NSF certified seal required. Klein 440 pot hooks, Klein conical gusset, Klein adjustable bullet feet, or Tabco SS3010, ST-120 Pot Rack, TA-11A Sink and two (2) SS drawers. TABLE, COOK (10') TN-022A 30" W x 120" L x 34" H; top and undershelf of 14 gauge polished stainless steel reinforced with 12 gauge stainless steel channels; undershelf to be welded and polished to each leg at 8" from floor; two (2) 15" x 20" x 5" stainless steel drawers. Must comply with all applicable NSF standards. 47

48 TABLE, WORK (6') TN-022B 72" L x 30" W x 34" H; top and undershelf of 14 gauge polished stainless steel with 12 gauge stainless steel channel support; legs, adjustable bullet feet, and drawer of stainless steel; undershelf to be to be welded and polished to each leg at 8" from floor. Must comply with all applicable NSF standards. TABLE, COOK (10') WITH POT RACK, LESS SINK TN-022C Rack height 7' 2"; stainless steel adjustable bullet feet; table 30" W x 120" L x 34" H; top and under shelf of 14 gauge polished stainless steel reinforced with 12 gauge stainless steel channel; under shelf to be welded and polished to each leg at 8 from floor; full length double bar pot rack over table, supported by capped 1-5/8" O. D. stainless steel pipe standards extending through stainless steel conical gussets, continuously welded, ground and polished to table top and back between table legs; bars of 1/4" x 2" flat bar stainless steel with semi circular ends and 36 fitted, removable double prong pot hooks; 16 gauge stainless steel under shelf with easily removable sections; two (2) 15" x 20" x 5" stainless steel drawers. Must comply with all applicable NSF standards TABLE, WORK (6') WITH POT RACK TN-022D Same as TN-22B, but with pot rack. Must comply with all applicable NSFstandards. TABLE, WORK (8') TN-022E Same as TN-022b, But with two (2) drawers and 96' L X 30" W X 34" H. Must comply with all applicable NSF standards.. TABLE, WORK (8') WITH POT RACK TN-022F Same as TN-22E, but with pot rack. Must comply with all applicable NSF Standards 48

49 TABLE, COOK (8') WITH SINK TN-022G Table 30" W x 96" L x 34" H; top of 14 gauge polished stainless steel, 1-1/2" rolled down edges, reinforced with 12 gauge steel channels; 1-5/8" O.D. 16 gauge stainless steel legs, gussets and 1" adjustable bullet feet; continuously welded, ground and polished to table top and back between table legs; 14 gauge stainless steel undershelf with easily removable sections; one (1) 15" x 20" x 5" drawer; swing spout, faucet and basket strainer for a 15" x 20" x 8" stainless steel sink on right end. Shop fabricated. NSF certified seal required. Klein adjustable bullet feet, or Tabco SS308, TA- 11A Sink and one (1) SS-1520 drawer or approved equal. TABLE, BAKER'S WITH BINS (8') TN L x 30 W x 34 H; 14 gauge stainless steel top with 6 H integral stainless steel riser at back table edges and ends; front and back table edges and ends turned down 1 5/8 ; all vertical and horizontal corners coved on at least ¼ radius; full length 8 W stainless steel condiment shelf mounted 18 above work surface; supported at ends and center by a ¾ 18 gauge stainless steel tubing braces formed to fit the riser, welded to riser ground, and polished; 2 turn up on shelf at back and ends; stainless steel gussets for leg mounting; horizontal corners of ¼ radius; three (3) approximately 20 x 20 x 5 drawers under table within an 18 gauge stainless steel enclosure on 6 legs with rounded vertical corners enclosed on all sides so as to be vermin proof; enclosure located at right end next to three (3) approximately 17 ½ x 22 ¼ x 27 ¼ stainless steel portable bins with depth of 14 mounted on four (4) 4 diameter, heavy duty ball bearing, rubber tired, swivel castors. Must comply with all applicable nsf standards. 49

50 SINK CONSTRUCTION I. GENERAL Sinks must comply with N.S.F. Standard No. 2 Food Service equipment and all applicable City of Houston Building and Health Codes. N.S.F. approved sinks will measure no more than 30" front to back by 111" left to right; with compartments measuring no less than 26.5" front to back by 24" left to right (i.d.) by no less than 14" deep (measured from base of well to highest fill level in each compartment, unless otherwise specified). Each compartment will be separated from the next compartment by a 2" wall separation. Drain board may be no smaller than the smallest horizontal dimension of the sink compartments and is to be mounted on the left or right side as indicated for each specific job. II. MATERIALS Sink compartments, drain boards and back splash will be constructed of 14 gauge number 304 (18-9) stainless steel; stainless steel welded, ground and polished to a number 4 type finish. Legs, braces and cross rails will be on stainless steel tubing at least 1.5" in diameter. Gussets and adjustable bullet feet will be of stainless steel. Removable under shelving will be of 16 gauge No. 302 stainless steel finished to a number 4 finish. Each will be provided with a finger tip release crumb cup strainer assembly with no less than a 1.5" drain. Faucets will be excluded from bid. Drain mechanisms to be twist type. III. CONSTRUCTION Minimum fabrication standards will equal or exceed N.S.F. Standard No. 2 Section 4.48 sinks. Construction will be of welded stainless steel. Rims will be 180 degrees 1.5" diameter rolled and extended over both ends and full length of unit. All corners and angles of 110 degrees or less made by two or more planes coming together will be rounded and fully coved in a continuous and smooth radius of no less than 8" above sink wells with no less than a 2" 45 degree return to the wall. Back splash to be pierced with 1-1/4" diameter holes on 8" centers to accommodate 2 faucet units. Faucets to be centered over sink compartments partitions. Bottom of each sink compartment to be pitched or stamped toward drain assembly. Drain assembly to be installed, sealed, tested and provided with a 4" nipple. Drain boards will be pitched toward sink and flat over their front to back dimensions. Pitch will be a minimum of 1/8" per 12 inches of drain board length (l to r). Drain board will be turned up a minimum of 2" and coved on not less than 3/8" radius to match sink front. Support for drain boards will be of same fabrication as sink units. Attachments of drain boards may not subtract from sink compartments minimum depth. Sink assembly and drain boards will be adequately supported by all stainless steel seamless supports. All gussets will be fully attached by welding, ground smooth, sealed from pest habitation and made easily cleanable. Legs are to be of no less than 1-1/2" stainless steel tubing 50

51 with cross rails welded 10" above floor; with no rail at back of sink well section. Drain boards to have matching legs and be fitted with removable under shelf. Sink and drain board assemblies to adequately support sink under full water loads. Front of sink compartments to be skirted completely across covering the partions and ending at the end sinks with no less than 16 gauge No. 302 stainless steel finished to a No. 4 finish. Note: Installation plumbing to be completed by others. SINK, POT AND PAN TN-047 SINK, VEGETABLE TN

52 SERVING LINE GENERAL REQUIREMENT Minimum 304 stainless steel with number 4 finish Framed to be 16 gauge /4 square tubing with 14 gauge stainless top 18 gauge stainless steel bottom shelving removable stainless front panel 16 gauge tray rail work shelf and plate shelf mounted on fold down brackets Sneeze guard to be high grade Lexan with polished edge legs or caster (5 ) with non marking gray tires fully adjustable NSF Counter/ Tray slide height Elementary schools 34" counter / 30" tray slide Middle School 34" counter / 32" tray slide High School 36" counter / 34" tray slide SERVING UNIT COLD 3 PAN SIZE WITH DOUBLE TIER DISPLAY STAND TN-069SS 120V 10A single phase NSF Atlas, Mod-U-Sever or approved equal SERVING UNIT HOT 5 PAN SIZE WITH SINGLE TIRE SERVING SHELF TN-070ESS 120/208V 19.0A single phase 5 cleared pass through opening NSF Atlas, Mod-U-Sever or approved equal 52

53 SERVING UNIT 3 PAN UNIT FLAT UNIT TN-071SS Atlas, Mod-U-Sever or approved equal SERVING UNIT CASHIER TABLE TN-072SS Atlas, Mod-U-Sever or approved equal HOT PAN DROP IN UNIT SINGLE PAN TN-114A Self-contained electric heated steam pan with one (1) 12" x 20" openings; steam pans must be riveted or screwed and not welded to support. Additional pans must be available as parts. The unit shall have an inner liner of 18 gauge stainless steel, type 304, grade Unit shall be of one piece all welded construction. Stainless Steel element holder, insulation pan, brackets, bottom, sides, and screws; all corners coved with a minimum of 1/4" radius. Insulation shall be fiberglass of 1-1/2" minimum thickness. There shall be a minimum of 1000 watts of heat per element, 208 V or 240 V, 60 C, single phase. The outer case shall be of 22 gauge stainless steel. The top shall be 18 gauge stainless steel, die pressed with a raised bead edge around the entire perimeter. There shall be a solid vinyl gasket under the bead edge to form a seal preventing seepage or marring of other equipment. The unit shall have embossed mounting lugs along inner surface of top frame to retain removable separator channels. The entire unit shall be removable from it's mounting without the use of tools. The unit shall be equipped with a 6 ft. long power cord. This unit shall be compatible with TN-110A. Specify 208 V or 240 V at time of order. Atlas TN114AA, Mod-U-Serv TN114AB, or approved equal. 53