3000 LPH MANUFACTURERS

Size: px

Start display at page:

Download "3000 LPH MANUFACTURERS"

Ann Jenkins
6 years ago
Views:

1 3000 LPH MANUFACTURERS Plant Introduction: Your requirement of Pure Water, We have designed the proposed plant to achieve the final treated water quality. The RO plant has been designed of 3,000 LPH. Raw Water Characteristics: 2000 PPM (Assumed) Treated Water Quality : <80 PPM Treated Water Quality From R.O. Plant: The above quality shall be achieved subject to: 1] Feed quality is same as specified in your enquiry. In case of any change in the quality of raw water, the same may have implications on the Operating parameters and End-water quality of the system. 2] Feed limiting condition mentioned in our offer is strictly maintained. 3] Operation of Water treatment plant is strictly followed in totality as per our operating manual and instructions. 4] Pure chemicals, Original Spares and consumables, recommended by us, are used in W.T.P. CAPACITY: 3000 LITERS PER HOUR PLANT 1.3 Operating conditions: Feed water Flow Rate Product water Flow Rate Average recovery Operating Pressure 5800 LPH % Approx 11 Kg/cm² System 1 : Mineral Water Plant 1. Raw Water Pump

2 2. Pressure Sand Filter 3. Activated Carbon Filter 4. Antiscalant Dosing System 5. Micron Cartridge Filter 6. High Pressure Pump 7. Reverse Osmosis System 8. Product Water Storage Tank 9. Product Water Transfer Pump 10. U.V. Disinfection System 11 Post Micron Cartridge Filter (Stage-1) 12. Post Micron Cartridge Filter (Stage-2) 13 Post Micron Cartridge Filter (Stage-3) 14 Ozone Generator Tank 15 Ozone Circulating Pump 16. Ozone Generator System SYSTEM 1 MINERAL WATER PLANT TECHNICAL SPECIFICATION 1. RAW WATER PUMP Quantity One No. Horizontal, Multi Stage, Centrifugal Material Of Construction SS 304 Make Panther / Equiv. Capacity 5800 LPH Discharge Pressure 3 kg/cm 2 Application To pump raw water at required pressure so as to enable transfer through the RO pre-treatment stage. 2. PRESSURE SAND FILTER Quantity One No. MOC Of Vessel SS 316 of Media Quartz Sand, Anthracite Sand, Cores Silex & Cheeps

3 Operating Flow Application 5800 LPH To filter out suspended solids up to 25 micron size 3. ACTIVATED CARBON FILTER Quantity One No. MOC Of Vessel SS 316 of Media Activated Carbon 900 Iodine Value & Chips Application To absorb the color, odour, free chlorine and some organic matters for the source water. 4. ANTI SCALANT DOSING SYSTEM Qty. of Dosing Pump Make of Pump Capacity of Pump MOC of Tank Make of Tank Capacity of tank Application One No. Electronic Metering Pump I Dose 0 6 LPH HDPE National. 100 Ltr. To ensure non-adherence of scale causing salts on the membrane surface by adhering to the crystals of scale causing salts. Not much change in ph value. Quantity 5. MICRON CARTRIDGE FILTER One No. M.O.C. of Housing SS 316 Material of Cartridge Pleated Diameter of cartridge 4 inches Length of Cartridge 20 inches No. of Cartridge Two No. Cartridge Rating 5 micron Frequency of change 3 months Application To protect the membrane and the high pressure pump from suspended particles.

4 6. HIGH PRESSURE PUMP Quantity One No. Vertical, Multi Stage, Centrifugal Pump M.O.C. Of Pump SS 304 Make Capacity Application Panther / Equiv LPH To boost water energy so as to pass through the membrane module at high pressure for obtaining the desired permeate quality. 7. RO MODULE Item of Membrane MOC of Membrane Make of Membrane Application RO Module consisting of Membrane Housing with RO membranes Mounted on skid. Composite Polyamide Polyamide Hydranautics / GE USA / Equiv.. To reduce dissolved salts present in water. 8. WATER STORAGE TANK Product Water Storage Tank As Per Budget & Space 9. PRODUCT WATER TRANSFER PUMP Qty. Offer. One Make Panther / Equiv. Operating Pressure 3 Kg / Cm 2 M.O.C. Of Pump SS U.V. DISINFECTION SYSTEM Qty. Offer One M.O.C. of Vessel SS 316

5 Make Of UV Lamp Discharge Flow Philips \ Sankyo 3000 LPH 11. POST MICRON CARTRIDGE FILTER (STAGE-1) Qty. Offer One Disposable Cartridge Operating Pressure 3 Kg. / Cm 2 M.O.C. Housing SS 316 Size of Cartridge 2.5 x 20 ( D x L ) Micron Rating POST MICRON CARTRIDGE FILTER (STAGE-2) Qty. Offer One Disposable Cartridge Operating Pressure 3 Kg. / Cm 2 M.O.C. Housing SS 316 Size of Cartridge 2.5 x 20 ( D x L ) Micron Rating POST MICRON CARTRIDGE FILTER (STAGE-3) Qty. Offer One Disposable Cartridge Operating Pressure 3 Kg. / Cm 2 M.O.C. Housing SS 316 Size of Cartridge 2.5 x 20 ( D x L ) Micron Rating OZONE TANK Ozone Tank As Per Budget & Space

6 15. OZONE PUMP Qty. Offer. Make One Panther / Equiv. Operating Pressure 3 Kg / Cm 2 M.O.C. Of Pump SS OZONE GENERATOR SYSTEM Dosage 6 Gm/ Hr. MOC Outer SS 304 & Contact Parts SS 316 Power Supply 230 Volts INSTRUMENTS A B C TDS METER Quantity Make Location ROTAMETER Quantity Make Location PRESSURE GAUGE Quantity Range One No. Digital / Equiv. RO Product Outlet Panel Mounted Two Nos. Glass tube type MMP / Equiv. RO Product flow & RO Reject Flow One Lot Bottom Entry Bourdon Tube Online 0-21 kg/cm², 0-7 kg/cm²

7 D Make PRESSURE SWITCH Make Low Pressure Switch High Pressure Switch Waree / Equiv. Indfos / Danfoss One One PRESSURE CONTROL VALVE E Location Reject Water Line Quantity One SS 316 F CONTROL PANEL One No. SCHEDULE OF EXCLUSIONS AND TERMINATIONS SCHEDULE OF EXCLUSIONS: 1] All civil works such as plant foundation of the equipments drain trenches, supporting structures & plate forms concreting etc. 2] Plant area, building illumination, ventilation & ear thing. 3] Final grouting of all the equipments. 4] Supply of power to Motors, regeneration chemical for trial run and Commissioning. 5] Laboratory testing facility, Instruments and reagents. 6] Lubricants, Oil and Grease as and when required. 7] Raw water storage tank.

8 8] All equipments, works and services, not specifically mentioned in our proposal. 9] Storage and site security. TERMINATION POINTS: 1] Inlet of Feed Water Pump. 2] Permeate & Reject Outlet of RO Water system 3] Overflow and drain pipe work of all vessels. 4] Power control termination at Control panel 5] Regerant inlet of each tank CLIENT TO PROVIDE: 1] Power supply : 440 Volts 10, three phases, 50 Hz. for all Pumps. 2] Service water : 5800 LPH Feed Water at the inlet of Feed water Pump. 3] Chemical : Anti Scalant Dosing Chemical

9 4] Lab testing facility : For Analysis of water 5] Labor : As and when required. SYSTEM - 2 Proposal for 2 Cavity Semi Automatic Pet Stretch Blow Molding Machine Auto Dropping. Pet Stretch Blow Molding Machine Description: Model: EFPL/2/C Capacity : 30ml to 2000 ml, Neck dia 25mm to 38mm Prod. Capacity: BPH / 20,000 bottles per day. Maximum mould thickness-150mm, Minimum mould thickness -140mm Clamping Force- 8 ton Oven: Number of Preform Holders-74, Number of Heating Modules- 1 Number of Heating Zones 8 Lamp Power W, Lamp Length -1220mm Stretching: Number of Stretch Rods-2 Stretching Stroke Max.-400 mm

10 Technical specifications: 1. Infrared pre-heating system. 2. Indexing Conveyor similar to fully Automatic machine. 3. Steady perform rotating in pre-heater. 4. Jana tics pneumatic system & water cooling system [Push & pull type] 5. Hydro-pneumatic Locking systems with operating mould memory in PLC 7. 1no Neck Mandrel will be given free of cost 8. Provision of dia form valve Particulars Compressor : 20 HP High Pressure (One No.) 2 TR Chiller: Temp -16 to 18 degree Celsius. (One No.) Air Dryer: One No. Power requirement Particulars: - Machine without utility : kw Motor : kw Compressor (20hp high pressure) : kw Chiller : kw Air Dryer : kw Total Connected load require with utility :- 36 kw SYSTEM-3 FULLY AUTOMATIC BOTTLE FILLING MACHINE (24bpm) Rotary Rinsing Filler & Capping Machine

11 Automatic Rinser: Stages BSP Capacity HP M.O.C Automatic Jet 2 Stages Rotary Rinsing 8 Bracket 24 Bottles / Minute 0.5 HP Contact Part S.S & Other M.S. BOTTLE RINSER: The machine will have 8 Rinsing nozzles. The frame structure will be of MS and will be suitably cladded with SS. The bottles from the Air conveyor will be taken by the star wheels and gripped by the In feed Neck Guide Plate.On Rotation the in feed Neck Guide Plate will deliver these bottles to the Rinsing Gripping Fingers. The gripping fingers will hold the bottles by neck and necessary guide bars will invert the bottle up side down by 180 degree. The duly inverted bottles will receive water from the rinsing nozzles on rear of the machine. The rinsing will operate from 90 to 270 degree rotation of the rinsing machine. Zero degree position is in front of the operator. In 180 degree rotation the washing cycles will be stopped and bottles will be re-inverted and delivered through Out feed Neck Guide Plate to the filling Unit.

12 Automatic Filler : Capacity Filling Capacity Power Required Solenoid Valve Operate by micro Switch 24 Bottles / Minute 200 ml to 2000 ml Three Phase M.O.C Contact Part S.S. 304 Capper : Capacity Single Head 24 Bottles / Min. RPM 1400 HP M.O.C 1hp Contact Part S.S.304 Salient Features 1. Neck Holding on Transfers 2. No Bottle No Rinse No Fill No Cap. 3. Drive is on chain of gears (Indexing Cam) hence low on Maintenance. 4. No Electronics involved in any function. Hence user friendly 5. Drive Motor (Make well make) Gear Box (Chamunda make)

13 6. All Liquid contact parts are of SS SS frame work and door will be of acrylic 8. Air blower 5 fit with blower + filters 9. SS conveyor 4 miters on the out feed of the conveyor Special Features: Air Blower Conveyor 5Ft Acrylic Cover With S.S. Structure & ALMN. Section 15Ft Conveyor With Shrink Tunnel Inspection TECHNICAL PARAMETERS FOR 200ml to 2,000 ml RINSING, FILLING & CAPPING Production Capacity Filling Capacity Neck Description Voltage Total Power 1400 Bottles / Hour 200 ml to 2,000 ml Standard for full range 415 V / 3 Ph / 50Hz 8 Kw Unit Dimensions (L x D x H) 2000 x 1600 x 2150

14 Air Blower Conveyor Wash Stages 5 fit 1 Stage Rinsing & Washing Heads 8 Filling Heads 5 Capping Heads 1 Structure Bottle Mono block PET Bottles only (NO GLASS) SYSTEM-4 Online Batch Coding Machine Main Features: High Reliability Large volume reservoir based ink system ensures stable performance in any application Patented sealed nozzle print head and true auto flush ensure reliable start-ups, even after extended periods of shut down Sealed cartridge fluid replenishment. Connectivity and Flexibility Built in Ethernet port enabling printers to be networked Built in web server to allow remote message selection and status monitoring All rasters and print formats on board allowing the machine to be configured from the user interface or via a networked PC

15 External USB port for location based set ups, moving messages between printers and service diagnostics Print up to two lines with a variety of print formats. Ethernet and USB ports as standard Clear codes on a wide range of substrates Technical Specification: 1. A100+ Control Unit 2. Control panel: Membrane touch button 3. Cabinet: Stainless steel (304) designed to IP53 (BS EN 60529: 1992) 4. Cabinet dimensions: 245mm x 450mm x 650mm (9.6 x 17.7 x 25.6 ) Weight: 33kg (73lbs) Character Control Auto repeat, Character width and height adjustment, Auto invert/reverse, User defined clock format, Print delay,sequential/batch numbering, Product counter, Inverse reverse and bold characters, Message repeat Iink System 5. Viscosity control: Automatic 6. Ink bleed control: Automatic on start up 7. Ink and make-up refill: 825ml (.87qt) cartridge automatically metered 8. Peltier: Optional Print head 1. Dimensions: 240mm x 41mm x 47mm (9.45 x 1.61 x 1.85 ) 2. Conduit length: 3m (11 8) 3. Positive air: Optional internal supply Environment 1. Temperature range: 5 45 C ( F) operating 2. Humidity: 10 90% (non-condensing) 3. Electrical requirements: Single phase, fully auto-ranging V, 47-63Hz Standard

16 Connections. 4. Product detector: npn/pnp12v 100mA for photocell or proximity detector.ip68 6-way socket Shaft encoder input: npn/pnp encoder 12V via IP68 6-way socket 5. Alarm beacon connector: IP68 7-way socket 6. Auxiliary alarms connector: IP68 9-way plug 7. Ethernet: IP68 RJ45 Connector 8. USB1.1: IP68 USB connector Options 9. User port connector: IP68 25-way socket 10. Data Input/Output Options: Serial RS232, Rate: k Baud, software configurable,accessories Full range of photocells, stands and bracketry Making More Time for your Business: Full control of networked factory printers from the comfort of your desk Simplified one-touch on/off button powers up the jet ready to start printing and when pressed to shut down, automatically flushes the head and powers off to ensure the machine is always available. Prepare/edit messages while the printer is still running to reduce code/product changeover times Set-up wizards improve accuracy, speed-up installation and allow printer tasks to be optimised fo

17 SYSTEM-5 Micro Biological & Chemical Lab As per bureau of Indian Standard Norms Lab Equipment, Chemicals, Glassware, Media, general Item (Bis license Fees Exclusive Extra at Actual)

Greensign systems & controls

Greensign systems & controls AN ISO 9001: 2015 CERTIFIED COMPANY RO PLANTS SOFTENER PLANTS ETP STP WTP PRESSURE BOOSTING & HYDRO-PNEUMATIC PUMPS CONTROL PANELS SPARES Greensign Turnkey Project for Mineral