Erie WA300. Application. Features. Two Zone Hydro-Air Relay General Instructions

Transcription

1 Building Systems - Americas Invensys Energy Solutions 354 lifford Avenue (Zip 6) P.O. Box 940 Loves Park, IL United States of America Erie A300 wo Hydro-Air elay eneral Instructions Application he A300 Hydro-Air control relay incorporates several relays to provide control for up to two hydro-air systems including two air handlers/a controls, two system heating circulators, one boiler/burner controller, and one domestic hot water circulator. Domestic hot water priority zone eliminates the need for additional relays to provide domestic hot water priority for indirect fired hot water tanks. N O E hermostats used with the A300 must switch on the heat and fan outputs when heat is called for. A300 wo Hydro-Air elay Features apable of controlling two hydro-air systems in one relay package Selectable fan delay of 90 or 80 seconds ommon 4 Vac transformer terminal Field replaceable circulator relays Large terminal connections Expandable up to four zones with the addition of a second A300 Litho in U.S.A. 3-0 F-70-

2 SPEIFIAIONS Inputs Outputs Environment Power for irculators: 0 50/60 Hz. Power for Fan enters: 4 50/60 Hz. Electrical: hermostat Anticipator Setting, Set to actual current draw of 4 V. irculator Switch ating, /4 0 Vac. Full Load, 6 amps. Locked otor, 43. amps. esistive, 6 amps. Fan enter Switch ating,.0 4 Vac. Mechanical: Fan on in Heat Mode, Field selectable 90 or 80 seconds. emperature Limits: Maximum Operating, 0 F (49 ). Shipping eight: 3 lbs (359 g). Location: NEMA ype (IP0). PIAL APPLIAIONS (wiring diagram) ater emperature ontroller Optional for 3-wire hermostats -Stat -Stat A SE 90 SE 80 SE 90 SE L L Fan iming Fan iming om om om 0VA om ater irc irc irc 4 VA 4 VA Fan enter 4 VA 4 VA Fan enter Boiler ontrol B B Burner Figure- ypical iring A300 - Boiler ontroller.

3 ater emperature ontroller Optional for 3-wire hermostats -Stat -Stat A SE 90 SE 80 SE 90 SE L L Fan iming Fan iming om om om 0VA om ater irc irc irc 4 VA 4 VA Fan enter Fan enter Hi Limit (N.. ontact) 4 Volt as Valve 0V/4 Volt ransformer Figure- ypical iring A300 4 Vac High Limit and as Valve. ater emperature ontroller -Stat -Stat 3 -Stat 4 -Stat A300 A SE 90 SE 80 SE 90 SE 80 SE 90 SE 80 SE 90 SE L L Fan iming Fan iming L L 3 Fan iming 4 Fan iming om om om om om 0VA om ater irc irc irc 4 VA 4 VA Fan enter 4 VA 4 VA Fan enter Boiler ontrol B B Burner 0VA om 3 irc 4 irc 4 VA 3 Fan enter 4 VA 4 Fan enter Figure-3 Four Hydro-Air System with Domestic ater Priority Using wo A300s. 3

4 INSALLAION Inspection Precautions Inspect the package for damage. If damaged, notify the appropriate carrier immediately. If undamaged, open the package and inspect the device for obvious damage. eturn damaged products. equirements ools (not provided) Screwdriver Digital multimeter raining: Installer must be a qualified, experienced technician Other accessories as appropriate eneral A N I N Electrical shock hazard! Disconnect power before installation to prevent electrical shock or equipment damage. Make all connections in accordance with the electrical wiring diagram and in accordance with national and local electrical codes. A U I O N Avoid electrical noise interference. Do not install near large conductors, electrical machinery, or welding equipment. Avoid locations where excessive moisture, corrosive fumes, vibration, or explosive vapors are present. Mounting iring Mount the A300 series to a suitable surface. Slotted keyholes and standard holes are provided for mounting purposes. Do not mount on a surface that exceeds 0 F (49 ). N O E Air handler # s transformer supplies 4 Vac power to air handler # s low voltage zone inputs on the A300. hermostats used with the A300 must switch on the heat and fan outputs on heat demand. ypical Installation o wire the A300 as a typical two zone hydro-air relay with dry contact output for turning on one boiler controller, two fan centers and, 0 Vac circulators. See Figure-. Line Voltage erminals. emove knockout below L and L terminals.. onnect line voltage: L 0 Vac hot. L 0 Vac neutral. round screw (green) to earth ground. 3. emove knockout below / terminals. 4. onnect hot water 0 Vac circulator: (left) 0 Vac circulator hot. (right) 0 Vac neutral. 4

5 5. emove knockout below / terminals. 6. onnect zone 0 Vac circulator: (left) 0 Vac circulator hot. (right) 0 Vac neutral. 7. emove knockout below / terminals. 8. onnect zone 0 Vac circulator: (left) 0 Vac circulator hot. (right) 0 Vac neutral. hermostat erminals. emove knockout above let,,, and terminals.. onnect zone thermostat: 4 Vac common. 4 Vac hot. Heat switched leg. ool switched leg. Fan switched leg. N O E hermostats used with the A300 must switch the fan on when there is a call for heat. thermostat terminals wire the same as zone, terminal optional for electronic thermostats. 3. onnect hot water priority controller: / Domestic hot water priority controller. Dry ontact erminals: he A300 allows terminals / to be wired to line voltage or 4 Vac gas valve with high limit. Electric Boiler/Burner ontroller (See Figure-). emove knockout below and terminals.. onnect boiler/burner controller to A300 / terminals: / Boiler/burner control /. 4 Vac as Valve with High Limit Boiler/Burner ontroller (See Figure-). emove knockout below and terminals.. onnect boiler burner controller in series between the transformer and the high limit control: 4 Vac hot from transformer. High limit controller. Fan enter erminals. emove knockout below left,,, and terminals.. onnect zone fan center: 4 Vac common. 4 Vac hot. ool relay. Fan relay. N O E fan center terminals are wired the same as zone. 5

6 Blower ime Selection Domestic ater Priority hermostat anticipator setting HEO OF OPEAION he A300 is shipped with a 90 second fan delay. o select a 80 second fan delay locate the delay timing jumper and move it to the 80 second position. he A300 relay has built-in domestic hot water priority logic. hen domestic hot water is demanded and the thermostats are calling for room heating, the circulators and blowers for zones and turn off, the boiler/burner and the priority circulator turn on until the hot water demand has been satisfied. If thermostats are in the cool mode, normal operation is not interrupted with a domestic hot water demand. If domestic hot water is required, the A300 turns on the boiler/burner control and the priority circulator (see Figure-4). Measure the amp draw of the 4 Vac input circuit. Set the thermostat anticipator to the same reading. he A300 relay is controlled by two low voltage single stage heat/single stage cool thermostats. he thermostats energize terminals and when a call for heat occurs. hermostat alling For Heat (,, and terminals are made) relay contacts close turning on the Boiler/Burner controller or low voltage load, circulator or line voltage load. After a 90 or 80 second delay the zone fan/blower is turned on. hermostat Not alling For Heat (,, and terminals are not made) relay contacts open turning off the Boiler/Burner controller or low voltage load, circulator or line voltage load. he zone fan/blower is turned off. hermostat alling For ooling (, and terminals are made) relay contacts close turning on the system compressor and fan/blower. hermostat Not alling For ooling (, and terminals are not made) relay contacts open turning off the system compressor and fan/blower. N O E operates identical to zone. Blower ime Selection N O E Blower time delay only applies to heat mode operations. he A300 incorporates a user selectable 90 or 80 seconds fan delay. his delay allows the hot water coil to warm before the blower engages. Domestic ater Priority hen domestic hot water (DH) is called for and the thermostats are calling for room heating, the circulator and blower for zones and turn off. he boiler/burner and the priority circulator turn on until the hot water demand has been satisfied. If the thermostats are in the cool mode normal operation will not be interrupted by a DH demand. Electronic hermostats All relays are compatible with electronic thermostats requiring and 3 wire (4 VA common terminal) connections. hermostats must turn on heat () and fan () terminals on a call for heat. MAINENANE 6 he A300 requires no maintenance. eplace defective units. egular maintenance of the total system is recomended to assure sustained, optimum performance.

7 FIELD EPAI he EP-0 cube relays are field replaceable. eplace any damaged or failed controls with new replacements. DIMENSIONAL DAA Figure-4 A300 Series Dimensions. 7

8 All specifications are nominal and may change as design improvements are introduced. Invensys Building Systems shall not be liable for damages resulting from misapplication or misuse of its products. he following trademarks are the property of Invensys: Invensys F-70- Printed in U.S.A.