REMKO CLK 20 Mobile Heaters

Size: px
Start display at page:

Download "REMKO CLK 20 Mobile Heaters"

Transcription

1 REMKO CLK 20 Mobile Heaters Operation Technology Spare Parts Edition GB M08 REMKO powerful like a bear

2

3 Operating Instructions Before commissioning/use of the equipment, these operating instructions must be read carefully! Our guarantee becomes null and void if the unit is used, set up, or maintained improperly or if modifications are made to the supplied unit without our prior consent. Subject to alterations! Mobile Heaters REMKO CLK 20 Contents Page Contents Page Safety Notices 4 Description of Unit 4 Regulations for Hot Air Heaters 5 Installation Regulations 6 Safety Devices 6 Chimney 7 Before Commissioning 7 Commissioning 8 Shutdown 9 Maintenance and Service 9 Trouble Shooting 11 Customer Service and Guarantee 11 Technical Data 12 Wiring Diagram 13 Exploded View 14 Spare Parts List 15 Commissioning of Forced-Air Oil Burner 16 Maintenance Log 18 EC Declaration of Conformity 19 Always keep these operating instructions in the direct vicinity of the installation site or unit. 3

4 Safety Notices Make sure to observe relevant local building and fire protection codes and abide by the regulations of the employers' liability insurance associations. The equipment may be operated only by persons who have received proper training in its operation. The equipment must be set up and operated in such a way that people are not endangered by exhaust fumes, hot air, and radiated heat and no fires can break out. The equipment may be operated only in room with a sufficient amount of air for the combustion. The equipment may be operated without a chimney in well-ventilated rooms. In this case, people may not constantly be in the mounting room. Corresponding prohibition signs must be posted at the entryways. A safety zone of 1.5 m around the equipment is to be maintained, even for non-flammable objects. The equipment is to be installed only on a noncombustible foundation. The equipment may be set up and operated only in an environment not at risk of fire or explosion. Mobile fuel containers may only be installed in compliance with technical regulations for flammable liquids TRBF 210 and 280. Any additional building ordinances of the country in which it is installed are to be observed. The intake guard grille must always be kept free of dirt and loose objects. Never insert foreign objects into the equipment. The equipment may not be exposed to direct water jets. All electrical lines of the equipment must be protected from damage (e.g. due to animals). Before all work on the device, the mains plug must be removed from the mains socket on principle. Safety devices may not be bypassed or blocked. Repair work on the electrical installation and on the burner may be carried out only by authorised, expert personnel for safety-technical reasons. The unit may never be disconnected from the power mains before the entire cool-down phase is up (except in emergency situations). Description of Unit The units are mobile, directly combusted hot air heaters (WLE) with heat exchangers and a chimney connection for commercial use. They are directly combusted with EL heating oil or diesel fuel and designed for fully automatic, universal, problem-free use. The units are only operated with a separate forced-air oil burner. The units are equipped with an electrical oil preheater via the nozzle stock. The units are equipped with a low-noise, maintenancefree, high-performance axial ventilator, a room thermostat socket, a connection cable with a plug, and a drum fitting. The units correspond with the basic safety and health requirements of all pertinent EU regulations and are easy to operate. Areas of application The units are mobile, directly combustible hot air heaters that supply instantaneous heat. They are only used for commercial purposes. Among other things, the units can be used in the following areas: Drying of new structures Spot heating of outdoor workstations Spot heating of workstations in open production rooms and halls not at risk of fire Heating of closed and open rooms, on a permanent or temporary basis De-icing of machines, vehicles, and non-flammable warehouse goods Temperature control of parts at risk of frost and greenhouses Function If the unit is switched to heating mode, the forced-air oil burner starts automatically. In fully automatic heating mode, the forced-air oil burner starts only when heat is required. After the burner has run for a short time, the temperature control thermostat "TR" (set temperature between 35 C and 40 C) automatically switches on the air supply fan. Hot air is blown out. When the room thermostat is in operation, the process above is automatically repeated depending on the amount of heat required. The temperature monitor "TW" (set temperature between 80 C and 85 C) monitors the internal temperature of the unit. After the unit has been shut down using the operating switch or by the room thermostats, the air supply fan continues to run for a certain period of time to cool the combustion chamber and the heat exchanger and then shuts down. This process may repeat several times. 4

5 Monitoring unit operation All functions of the unit are fully automatic and monitored for safety by the safety devices and the automatic burner relay (part of the forced-air oil burner). If the flame burns irregularly or goes out, the unit is switched off by the automatic burner relay. The control lamp on the control panel and the malfunction lamp of the automatic burner relay light up. Before the unit can be restarted, the automatic burner relay must be released manually by pressing the external reset button on the control panel or the reset button on the automatic burner relay. The temperature control thermostat (TR) regulates the operation of the fan. The temperature monitor (TW) limits or regulates the temperature of the unit in heating mode. The safety temperature limiter (STB) interrupts the heating mode when extreme overheating occurs or if the temperature monitor (TW) breaks down or becomes defective. The STB can be released manually only after Before the STB is released to begin operation again, the causes for the activation of the STB must be localised. Regulations for Hot Air Heaters When using the equipment, the following directives must be observed: Feuerungsanlagenverordnung (FeuVo) (Furnace Installation Ordinances) of the individual states Unfallverhütungsvorschrift (UVV) (Accident Preven tion Regulation) "Heiz-, Flämm- und Schmelzgeräte für Bau- und Montagearbeiten" (Heating, Burning, and Melting Equipment for Construction and Mounting Work) (VBG 43) Arbeitsstättenrichtlinien ASR 5 (Workstation Guidelines) Arbeitsstättenverordnung (Workstation Ordinance) 5 and 14 Ordinances regarding the execution of the Bundes- Immissionsschutzgesetzes (BImSchG) (Law Concerning the Protection against Harmful Effects on the Environment through Air Pollution, Noise, Vibrations, and Similar Factors) and the legal regulations enacted as a result (ENEG) Excerpt from the Unfallverhütungsvorschrift (VBG 43) 37 Operating personnel The equipment may be operated only by persons who have received proper training in its operation. 38 Installation (1) The equipment must be installed in a stable location. (2) The equipment must be set up and operated in such a way that people are not endangered by exhaust fumes, hot air, and radiated heat and no fires can break out. (3) The equipment may be operated only in rooms with a sufficient amount of air for the combustion and the exhaust fumes are conducted outside via chimneys. A natural air supply that suffices for combustion is present if the following applies: The room volume in m³ corresponds to at least 10 times the nominal heating capacity in kw of all equipment being operated in the room and a natural exchange of air is guaranteed by windows and doors. (4) Deviating from Section 3, the equipment may be operated without a chimney in rooms that are well aerated and ventilated and the amount of pollutants in the breathing air that is hazardous to health do not reach an unreasonable concentration. Natural aeration and ventilation is present if one of the following applies: 1. The room volume in m³ corresponds to at least 30 times the nominal heating capacity of all equipment being operated in the room and a natural exchange of air is guaranteed by windows and doors. 2. Air openings for supply and outlet air in the ceiling and floor exist and cannot be closed. The size of these openings in m 2 corresponds to at least times the nominal capacity in kw of all equipment being operated in the room. (5) The equipment may be set up and operated only in rooms and areas not at risk of fire or explosion. 44 Room drying (2) Deviating from 38 Sect. 3, heaters may be used to dry rooms with a sufficient air supply for combustion without the exhaust fumes having to be conducted outside via chimneys. People may not constantly be in these rooms. Prohibition signs should be hung at the entrances of these rooms. 53 Testing (2) According to the conditions for use, the equipment should be tested by an expert for its proper working order as required, but at least once a year. The exhaust emission specifications of the burner must be checked. 54 Monitoring (1) The persons assigned with the operation of the equipment must check for noticeable defects of the operating controls and safety devices and for the existence of protective mechanisms before starting work. (2) If defects are discovered, the supervisor must be informed. (3) In case of defects that endanger the operating safety of the unit, it must be shut down. 55 Rule infringements Whoever violates the regulations of VBG 43, whether deliberately or due to negligence, is acting contrary to regulations according to 710 Sect. 1 of Reichsversicherungsordnung (RVO) (Reich Insurance Code). 5

6 Installation Regulations When the equipment is in use, the safety guidelines of the employers' liability insurance associations, the respective country construction ordinances, and the burning appliance regulations basically apply. Avoid underpressure or overpressure in mounting rooms since these states always lead to combustion-technical problems. Make sure the fresh air supply has been adapted to the respective fan output (see model plate). The forced-air oil burner must be equipped with a separate combustion air supply if necessary. Outdoor installation Due to the operation of the equipment, no dangers or unreasonable nuisances may arise. The equipment operator must guarantee that unauthorised persons cannot manipulate the equipment or the energy supply. Because rain and snow can be pulled in through the supply air fan, a suitable protective covering should be used. Installation in closed, well-ventilated rooms without a chimney The equipment may only be operated when the minimum amount of air required for combustion according to 38 Sect. 4 (page 5) is supplied. A safe exhaust of the waste gases is to be ensured to exclude an inadmissible pollution of the room air. Fresh air is supplied from below. Waste gases are expelled upwards. Safety distances To guarantee safe equipment operation and maintenance, a safety distance of 1.5 metres around the device must be observed. The floor and ceiling must be fire-resistant. Heating rooms The equipment may be used for room heating only with a room thermostat (accessory). The supply of the fresh air required for proper combustion must be guaranteed. Electrical connection The equipment is operated at 1~ 230 V/50 Hz. The electrical connection of the equipment must be performed at a certain supply point with an earthleakage circuit breaker according to VDE Suitable cable extensions may be used only when unrolled. Safety Devices The equipment has the following safety or monitoring devices: Temperature control thermostat (TR) Temperature monitor (TW) Safety temperature limiter (STB) Temperature control thermostat (TR) The temperature control thermostat switches the circulating fan on and off. The switching point is set in the switch box using the "Scale 21 60" controller. Setpoint approx C. Temperature monitor (TW) In heating mode, the temperature monitor limits both the temperature of the unit and of the air being blown out. The switching point is set in the switch box using the "Scale " controller. Setpoint approx C. Safety temperature limiter (STB) The STB controls the temperature monitor. The switching point has a permanent setting. The burner is prevented from being restarted if the STB is activated. After the cover next to the control panel is removed, the reset button must be pressed from the outside. After the STB has been reset, the cover must be remounted. Before an STB reset, check the operating conditions to ensure that the STB temperature is not exceeded again. Information on the safety devices The safety devices are equipped with a sensor monitoring feature and are resistant to cold down to -20 C. Below -20 C, it switches off; when the temperature rises above this temperature, it switches on again. When the sensor or capillary tube is damaged or when an excess temperature of approximately 220 C is reached, the filling medium is emptied and the safety device switches off. The controller is no longer operable and must be replaced. If it is necessary to replace the STB, only the original REMKO spare part should be used. Make sure to install and mount the device carefully. Do not bend the capillary tubes in the direct vicinity of solder points. When installing the capillary tubes, be careful not to damage or bend them too sharply. The sensors may only be mounted in the mounting strap. The sensors must always be free of dust and dirt. 6

7 Max. 1 metre Over 1 metre Chimney When the units are operated outside or in open spaces, you do not need a chimney. We recommend using a onemetre-long chimney pipe with a rain cover at the top to (see Example 2) to prevent the penetration of rainwater and dirt. If the unit is used as a room heater, the waste gases must be conducted outside. Make absolutely sure that counterpressure is not created by an improperly installed chimney. The chimney pipe parts must be laid in such a way that no counterpressure can arise. The unit operates without malfunctions if the chimney has been installed at an incline and assembled with vertical end pipes. The chimney must reach at least beyond the gutters, but preferably above the top of the roof to prevent counterpressure caused by weather conditions (e.g. wind). All chimney pipe parts must be securely fastened. They may not be smaller in diameter than the chimney connection of the unit. A minimum distance of 0.6 m to flammable objects must be maintained. Chimney pipe parts and fasteners are available as accessories if required. When a chimney is used, the adjustment of the burner must be adapted accordingly. Before Commissioning Before commissioning, the equipment should be checked for noticeable defects of the operating and safety devices, as well as for proper mounting and correct electrical connection. In any case, observe the following: Install the device on a stable surface. Guarantee a sufficient combustion air supply. Make sure the air intake and outlet is unobstructed. Avoid overpressure and underpressure in the room where the unit has been installed. Make sure that enough fuel is supplied. Use only clean EL heating oil or diesel. Do not use biodiesel. Flexible fuel lines must be particularly protected from damage, e.g. by forklifts, animals, and so on. Paraffin formation at low outside temperatures Even in case of low outside temperatures, free-flowing heating oil must be available in sufficient quantities. Paraffin formation can already take place at temperatures below 5 C. Corresponding measures must be taken to prevent it. Winterproof EL heating oil or diesel. Electrical connection The equipment is operated at 1~ 230 V/50 Hz. The electrical connection takes place using an installed mains cable with a safety plug. The electrical connection of the equipment must be performed at a certain supply point with an earthleakage circuit breaker according to VDE Example 1 Example 2 Example 3 Operation with extended chimney. Requires condensate trap. Operation without extended chimney. Max. 1 metre Inadmissible installation Important information To prevent damage to the combustion chamber caused by moisture build-up (condensation) (see Example 3), make sure that the chimney pipe has a properly installed condensation trap (see Example 1). Extension cords may be extended only by authorised electricians depending on the length of the cable and the connected load of the unit and under consideration of the local use. All cable extensions may be used only when unrolled. Additional information The exhaust emission specifications of the forced-air oil burner must be checked or set by authorised personnel according to the respective local conditions. 7

8 Commissioning Someone who has been sufficiently trained in the corresponding handling of the unit must be assigned with its operation and monitoring. Important notice before the startup of a cold unit The preheating of the nozzle stock delays the start of the unit dependent on temperature. Control panel Safety temperature limiter Operating 4 3. Place the room thermostat in a suitable spot. The thermostat sensor may not be located within the flow of warm air and may not be directly attached to a cold foundation. 4. Adjust the desired temperature on the room thermostat. 5. Switch the operating switch to the "I" position (heating). If heat is needed, the forced-air burner switches on automatically and the unit functions fully automatically. Connecting the unit to the power supply 1. Switch the operating switch to the "0" position (off). 2. Connect the mains plug of the unit only to a properly installed and sufficiently secured mains socket. 3. Open all shut-off fittings in the oil supply. When operating the unit for the first time, air in the oil supply can cause the burner to shut down due to a malfunction. Heating without room thermostat The equipment works in continuous operation Connect the jumper plug (2) included in delivery with the thermostat socket (1) on the unit. 2. Switch the operating switch to the "I" position (heating). Fully automatic heating with room thermostat The unit operates fully automatically depending on the room temperature. 3 1 Jumper plug Thermostat socket Burner reset button Burner Fault red control lamp Operation green control Note about the "Operation" control lamp The control lamp indicates that the unit is in "Heating" mode. When the unit is in "Ventilation" mode, nothing is displayed 1. Disconnect jumper plug Connect the plug (3) of the room thermostat (4) together with the thermostat socket (1) of the device. Ventilation In this switch position, only the supply air fan runs and the unit can be used for air circulation. 1. Turn the operating switch to the "II" position (ventilation). 2. Please note: in this mode, regulation of the thermostat and heating mode are not possible. Hot air distribution The units are equipped with a high-performance axial fan. This fan has been designed to transport the hot air directly and effectively. The distribution of the air should preferably take place using the on-site outlet nozzle. If necessary, pipes or special hot-air or foil hoses for air distribution in the possible area of fan output (observe the channel resistance/equipment compression). Use only hot air hoses (accessories) approved by Remko. In the process, pay attention to the air direction! To prevent heat from building up, the pipes and hoses may not have sharp kinks and bends. Counterpressure may not be allowed to build up when using hoses to heat enclosed spaces. If suction temperatures increase or if there is resistance at the air output opening, the forced-air burner can be switched off at short notice by the temperature monitor (TW) during heating. When the temperature falls, the burner restarts automatically. If the intervals are too short, the length of the hot air pipes and hoses should be checked. Avoid starting the burner in frequent cycles (run times under five minutes). If the temperature becomes too high, the heating mode is interrupted permanently by the STB! 8

9 Shutdown 1. Switch the operating switch to the "0" position (off). 2. Shut off the fuel supply. Important information about the equipment's cooldown phase The supply air fan runs to cool off the combustion chamber and the heat exchanger further and does not switch off till later. The fan may run several times until it switches off permanently! Never (except in emergency situations) interrupt the mains connection before the entire cooldown phase comes to an end. Our guarantee does not cover damages caused to the unit by overheating. Maintenance and Care The regular care and observance of some basic prerequisites guarantee malfunction-free operation and a long service life of the unit. Before all work on the device, the mains plug must be removed from the mains socket. Keep the unit free of dust and other deposits. For cleaning, use a clean, slightly moistened cloth with which you can wipe off the dirt from the surface. Do not use a water jet. Do not use caustic cleaning agents or cleaning agents containing solvents. Even in case of extreme soiling, only use suitable cleaning agent. Use only clean EL heating oil or diesel as fuel. Look for paraffin formation. Do not use biodiesel. Check the fuel filter for soiling at regular intervals. Dirty filters must be replaced. Check the unit for mechanical damage and have defective parts replaced by an expert. Check the fan blades and combustion chamber with the heat exchanger for soiling at regular intervals and clean them when necessary. Check on-site oil tanks for soiling and foreign bodies regularly and clean them when necessary. Always make sure the chimney and combustion air duct are always in perfect working order. Regularly check safety devices to ensure that they are working properly. Always keep the sensors of the safety devices free of dust and dirt. Have the exhaust emission values of the forced-air oil burner checked regularly by authorised personnel. For safety reasons, we recommend the conclusion of a maintenance contract. Observe the maintenance and service intervals. Adjustment and maintenance tasks may be performed only by authorised expert personnel! Cleaning After every heating period or even earlier, depending on the operating conditions, the equipment, including the heat exchanger, combustion chamber, and forced-air oil burner, must be cleaned of dust and dirt. Parts subject to wear, such as waste gas suppressors, seals, oil filter inserts, and oil nozzles, should be checked and exchanged if necessary. Cleaning the heat exchanger 1. Set the operating switch to the "0" position and pull the plug from the mains socket.. 2. Remove the blow-out cone (1) after unscrewing the four fixing screws. Any hot air hoses or pipes must be dismantled as well if pertinent. 3. Remove the revision cover (2) and take the waste gas suppressor (4) out of the unit. 4. Clean all waste gas flues (5). A special cleaning is available as an accessory under EDP No Clean the waste gas suppressors and replace any damaged ones if necessary. 6. Check the seals (3) of the revision cover and replace any damaged seals. 7. Please observe the notices on the next page. 9

10 Important information about mounting the revision cover Make sure that the seals and revision cover are correctly placed. When mounting the revision cover, make sure the fixing nuts are tightened evenly. Uneven tightening of the fixing nuts may result in leakage. Cleaning the combustion chamber 1. Set the operating switch to the "0" position and pull the plug from the mains socket. 2. Remove the combustion chamber cover. 3. Pull the burner plug. 4. Unscrew the four quick-release fasteners of the mounting base plate from the mount (1). The quick-release fasteners and the mounting base plate are not shown in the drawing below. 5. Carefully remove the complete mounting base plate from the front of the unit. The fuel line does not have to be dismantled. 6. Place the mounting base plate next to the unit. 7. Unscrew both cylinder head studs (2) from the housing (3). 8. Remove the housing from the front of the combustion chamber and set it aside. Assembling the burner seal and the burner 1. Check the burner seal (4) and replace it if necessary. 2. Push the burner seal onto the flame tube of the housing. 3. Mount the burner seal (4) and the housing (3) to the combustion chamber flange using both cylinder head studs (2). 4. Attach the mounting base plate using the four quick-release fasteners. 5. Insert the burner plug again and close the combustion chamber cover. After all work on the device, perform an electrical safety test according to VDE Additional maintenance information Maintenance work on the forced-air oil burner may only be performed by authorised personnel. The exhaust emission limits must be observed in accordance with 11 of the small furnace ordinance (1. BImSchV). The exhaust emission analysis may be perfomed only when the combustion chamber cover is closed. Trouble Shooting 4 3 Important safety notices Repair work on the electrical installation and on the forced-air oil burner may be carried out only by authorised, expert personnel for safety-technical reasons. Before all work on the device, the mains plug must be removed from the mains socket. 9. Remove the burner seal (4). 10. Do not damage the burner seal. A damaged burner seal may lead to faulty air intake. 11. Clean the combustion chamber using a vacuum cleaner through the opening of the burner. A special boiler cleaning set for the REMKO industrial vacuum cleaner is available as an accessory. 1 2 The unit does not start 1. Check the mains connection. 1~ 230 V. 2. Switch the operating switch to the "I" position. 3. Check whether the "Operation" control lamp on the control panel has lit up. It must indicate that the unit is in "Heating" mode. 4. Check that the jumper plug or the thermostat plug has been plugged in correctly. 5. Check the room thermostat setting. The temperature set on the room thermostat must be higher than the room temperature. 6. Check whether the safety temperature limiter (STB) has activated. You must remove the protective cover next to the control panel. 10

11 Customer Service and Guarantee 7. Before resetting the STB, you must determine the reason it was activated and take appropriate measures. The following are possible reasons: The unit could not cool down because the power supply was interrupted. The temperature of the air being blown out is too high because hoses are not directing air properly. Air intakes and outlets are blocked. 8. Check whether the "Burner Fault" control lamp on the control panel has lit up. If so, release the automatic burner relay by pressing the reset button. 9. Switch the operating switch to the "II" position. If the supply air fan now starts, look for the malfunction in the vicinity of the burner. Forced-air burner and power supply 1. Check the oil filter for soiling. Replace the dirty filter. 2. Make sure the shut-off valve on the oil filter is open. 3. Make sure there is enough fuel in the fuel container. 4. Check whether paraffin has accumulated in the heating oil. This can occur at temperatures as low as 5 C already. 5. Check oil tubes for damage. 6. Check the sensors and capillary tubes of the safety devices for damage or soiling. 7. Make sure the temperature monitor (TW) is working properly using suitable equipment. 8. Check the forced-air oil burner for any soiling of the nozzle, baffle plates, filters, and so on. The prerequisite for any warranty claims is that the customer or its recipient has returned the completed "Warranty Document" included in delivery to REMKO GmbH & Co. KG at the time of the sale and commissioning of the equipment. The devices were tested several times at the factory for proper function. If any malfunctions should occur, however, which cannot be eliminated by trouble shooting measures performed by the operator, please consult your specialised dealer or contract partner. Another operation other than that described in these operating instructions is not permitted. Nonobservance leads to the extinguishment of any liability and warranty claims. Proper use Due to their conception and equipping, the devices are designed solely for heating and ventilation purposes in industrial or commercial use. The manufacturer is not liable for damage that occurs due to nonobservance of manufacturer instructions or the legal requirements or due to unauthorised changes to the device. Supply air fan does not start 1. Check whether the fan blade is running smoothly. 2. Check the power cord on the air supply fan for damage. 3. Check the operating capacitor of the fan. It is located in the switch box of the unit. 4. Make sure the temperature control thermostat (TR) is working properly using suitable equipment. Important information about unlocking the burner If the burner shuts down again due to a malfunction during the starting phase, it may not be unlocked again until a five-minute wait has passed. Further unlocking procedures must not be performed. A danger of explosion exists. 11

12 Technical Data Model CLK 20 Max. nominal heat load kw 22 Nominal heat output kw 20 Nominal air volume flow m³/h Pressure (max. total) Pa 95 Fuel EL heating oil or diesel according to DIN or diesel fuel Max. fuel consumption L/h 2.20 Oil nozzle (Danfoss) 2) USG 0.5/60 S Pump pressure, approx. 2) bar Max. chimney loss % 9 Chimney volume, approx. kg/h 35 Furnace resistance, approx. (start/operation) Pa 140/40 Required chimney draft Pa 0 Electrical connection V/Hz 1~ 230/50 Max. power consumption (ges. Gerät) W 320 Max. nominal current (ges. Gerät) A 1.45 Max. power consumption (Ventilator) W 130 Max. nominal current (Ventilator) A 0.6 Operating capacitor of the fan µf 3 Fuse protection (on site) A 10 Temperature increase ( t ) K 41 Sound pressure level L pa 1m 3) db (A) 60 Air outlet ø mm 300 Chimney adapter Ø mm 130 Total unit length mm Total unit width/with wheel attachment mm 510/580 Total unit height/with wheel attachment mm 735/880 Weight with forced-air oil burner kg 94 2) The listed nozzle sizes and pump pressures were determined on the basis of adjustment tests on a test stand. The oil throughput was measured out. (The specifications serve only as standard values due to product-specific nozzle and pressure tolerances and oil temperatures.) 3) Noise measurement according to DIN Cl. 3 (without burner operation) We reserve the right to make changes in dimensions and design in the interest of technical advances. 12

13 Wiring Diagram TR TW STB RT S A 4B 2A 0 5B 3A II 6B C H2 H1 S2 KL N N M braun Brown Orange orange Black schwarz Blue blau S3 IB4 T2 T1 N L1 #2 #3 #4 N L1 PE WS HW C = Capacitor S1 = Operating switch H1 = Control lamp (green) S2 = Reset button (burner) H2 = External control lamp (red) STB = Safety temperature limiter KL = Terminal strip TR = Temperature control thermostat M = Fan motor TW = Temperature monitor RT = Thermostat socket WS = Burner plug, 7-pole We reserve the right to make changes in dimensions and design in the interest of technical advances. 13

14 Exploded View STB sensor TW sensor TR sensor Ansicht View Bedienungstableau of control panel We reserve the right to make changes in dimensions and design in the interest of technical advances. 14

15 Spare Parts List No. Description Ref. No. 1 Cover plate Insulation, top Insulation, right Side cover, right top Side cover, right bottom Base plate Insulation, bottom Side cover, left top Side cover, left bottom Insulation, left Rear panel, cpl Partition Burner seal Switch box, cpl Seal for switch box Front panel Angle support, oil filter Oil filter, cpl O-ring Filter insert Oil filter cup Blow-out cone Burner compartment cover Lock for burner compartment cover Support base Axle Wheel Wheel cap Circlip Combustion chamber, complete Waste gas suppressor (set) Revision cover Seal for revision cover Rosette for chimney connection Transport handle, front Transport handle, rear Transport handle, centre Fan, cpl Capacitor (fan) Safety temperature limiter (STB) Temperature control thermostat (TR) Temperature monitor (TW) Operating switch Control lamp, green (operation) Control lamp, red (burner fault) Reset button (burner) Thermostat socket Jumper plug Mains cable with plug Not shown Burner plug, 7-pole Forced-air oil burner, cpl Drum fitting, cpl Cleaning brush, cpl When ordering spare parts, please indicate the reference number and the machine number (see model plate)! 15

16 Commissioning of the Forced-Air Oil Burner The forced-air oil burner may be commissioned only by expert personnel! Preparation Before starting with the adjustment of the forced-air oil burner, perform the following tasks: 1. Remove the cover of the burner compartment. 2. Remove the fuel line from the burner and pull the burner plug. 3. Unscrew the four quick-release fasteners of the mounting base plate (1) at Position A. A Adjusting the air flap Adjust the air flap using the adjusting screw (7) in such a way that Distance A between the air flap (8) and the stop (9) amounts to approx. 6 mm A To adjust the necessary distance, proceed as follows: 1. Loosen the knurled nut (10) and turn the adjusting screw (7) accordingly. Clockwise rotation: Distance A becomes smaller Counterclockwise rotation: Distance A be comes larger A 1 4. Carefully remove the complete mounting base plate from the front of the unit. 5. Place the mounting base plate somewhere suitable for the further tasks. Required nozzle sizes Selecting the required oil nozzle depends on the pump pressure and the unit capacity. You may only use an oil nozzle that is suitable for the shape of the respective burner chamber with corresponding spray angle, cone properties, and throughput. You can find the necessary nozzle size in the technical data. Setting the ignition electrode and baffle plate 3 D D E After adjusting the distance, retighten the adjusting screw using the knurled nut (10). The optimum setting must be adapted to the local conditions and the respective chimney. Mounting base plate After the ignition electrode, baffle plate, and air inlet nozzle are adjusted, the mounting base plate is remounted. 1. Attach the mounting base plate using the four quick-release fasteners. 2. Mount the fuel line to the burner. 3. Reinsert the burner plug All dimensions are approx. 5 Mount the baffle plate (D) in such a way that the hole (E) is flush with the photo cell. 16

17 Secondary air setting (nozzle stock) 1. Set the nozzle stock (2) to the approx. 1.5 marking using the adjusting screw (1). 1 2 Measuring the combustion gases Every stationary combustion plant must be check by measuring the exhaust emission values according to the first Bundesimmissionsschutzverordnung (1.BImSchV) (German Air Pollution Act). The owner is obliged to have the combustion plant monitored by measurements performed by the local chimney sweep up to four weeks after commissioning. In addition, according to 9 and 15 of 1. BImSchV, the emission values must be checked annually by the local chimney sweep (oil derivatives, soot, exhaust emissions). Adjusting the air inlet nozzle 1. Lock the adjust lever (3) of the air inlet nozzle in the locking position (3) (see arrow). 3 Setting the pump pressure For initial burner operation and after each time the burner is serviced, the oil pressure must be adjusted or Never operate the pump without oil! 1. Remove the stopper on the "P" measuring connection and mount the oil manometer (seal!). 2. Open all oil shut-off fittings.. 3. Switch on the burner using the operating switch. 4. Set the required oil pressure via the adjusting screw (4) after loosening the counter nut (5). Clockwise: Increase pressure Counterclockwise: Reduce pressure 5. After making the pressure setting, secure the adjusting screw using the counter nut (5). 4 5 Important information All specifications only serve as presettings and must be readjusted or adapted according to the local conditions during the exhaust emission analysis. The settings can be made only if the chimney has been properly installed! On principle, the equipment must be operated at the nominal load. To guarantee the optimum function of the burner, please note that annual maintenance must be performed according to DIN For this purpose, you should conclude a maintenance contract. 6. Switch on the unit using the operating switch. 7. Dismantle the oil manometer and replace the stopper (seal!). Additional pump information Perfect fuel quality is absolutely necessary for the lubrication of the pump gear. Never suction up water residue or fine dust that tends to harden (such as cement). Never let the unit run with a dry pump for a longer period of time. P 17

18 Maintenance Log Model :... Model No. :... Burner :... Burner No. : Clean unit surface Clean unit interior Clean fan blade Clean combustion chamber Clean heat exchanger Replace waste gas suppressors Replace seals - revision cover Replace seals - burner Replace filter - fuel Check safety devices Check electric safety Check protective mechanisms Check unit for damage Maintenance burner *) Test run Comments: Date: 2. Date: Date: Date: Date: Signature Signature Signature Signature Signature 6. Date: 7. Date: Date: Date: Date: Signature Signature Signature Signature Signature 11. Date: 12. Date: Date: Date: Date: Signature Signature Signature Signature Signature 16. Date: 17. Date: Date: Date: Date: Signature Signature Signature Signature Signature *) Maintenance work may be performed on the forced-air oil burner only by authorised expert personnel; settings and adjustments must comply with the legal regulations (1. BImSchV. (German Air Pollution Control Act). A corresponding test log must be kept.

19 EC Declaration of Conformity We hereby declare that the following hot air heater corresponds to the pertinent basic requirements of the respective EC directive (s) due to its conceptual design and construction in the version in which we have brought it on the market. Important Note: This declaration becomes null and void if the unit is used, set up, or maintained improperly or if modifications are made to the supplied unit without our prior consent. Name of manufacturer: : REMKO GmbH & Co. KG Air Conditioning and Heating Technology Im Seelenkamp Lage, Germany Unit (machine) design Series : REMKO CLK 20 Serial number : : Mobile hot air heater for operation with a separate forced-air burner Valid regulations : MA - RL 89/392/EEC Machinery Directive [98/37/EC] NS - RL 73/23/EEC Low Voltage Directive EMC RL 89/336/EEC EMC Directive Applied standards : EN 292-1; EN 292-2; EN 294; EN 349; EN ; DIN VDE 0116; DIN ; DIN EN ; EN ; EN 55104; EN ; EN ; Lage, 5 August 2003 REMKO GmbH & Co. KG ppa.... Signature (Technical Management) 19

20 REMKO GmbH & Co. KG Air Conditioning and Heating Technology Im Seelenkamp Lage, Germany Postfach Lage, Germany Phone Fax

REMKO CLK Mobile automatic heater

REMKO CLK Mobile automatic heater REMKO CLK Mobile automatic heater Operation Technology Spare Parts Edition GB M04 REMKO - powerful like a bear. Operating Instructions Read these instructions carefully before setting up/operating the

More information

REMKO DZH. Oil Heaters. Operation Technology Spare Parts. Edition GB D04

REMKO DZH. Oil Heaters. Operation Technology Spare Parts. Edition GB D04 REMKO DZH Oil Heaters Operation Technology Spare Parts Edition GB D04 Contents Safety Notices 4 Device Description 4 Mounting Regulations 5 Commissioning 6 Shutdown 7 Maintenance and Care 8 Trouble Shooting

More information

REMKO CLK CLK 30, CLK 50, CLK 70, CLK 120, CLK 150

REMKO CLK CLK 30, CLK 50, CLK 70, CLK 120, CLK 150 REMKO CLK CLK 30, CLK 50, CLK 70, CLK 120, CLK 150 Automatic oil/gas heaters Operation Technology Spare parts Edition GB I12 Contents Safety notes 4 Unit description 4 Specifications for fan-assisted

More information

Propane Heater REMKO PGM 30 REMKO PGM 60

Propane Heater REMKO PGM 30 REMKO PGM 60 Propane Heater REMKO PGM 30 REMKO PGM 60 Operation Technology Spare Parts Edition GB L07 REMKO strong as a bear. Operating instructions Make sure to read these instructions carefully before starting/using

More information

Oper at ion Technology

Oper at ion Technology CLA 25-100 Aut omat i c Oil/ Gas Heat er s Edit ion GB- 709 Oper at ion Technology Or iginal REM KO Spar e Par ts REM KO - alles bär enst ar k. Oper at ing inst r uct ions Make sure to read these instructions

More information

IDE 20 / IDE 30 / IDE 50 IDE 60 / IDE 80

IDE 20 / IDE 30 / IDE 50 IDE 60 / IDE 80 IDE 20 / IDE 30 / IDE 50 IDE 60 / IDE 80 EN OPERATING MANUAL OIL HEATER TRT-BA-IDE20-30-50-60-80-TC-001-EN Table of contents Information on the use of this manual... 1 Scope of delivery... 1 General safety...

More information

DH-Direct Fired Poultry Farm Diesel Heater

DH-Direct Fired Poultry Farm Diesel Heater DH-Direct Fired Poultry Farm Diesel Heater Comparison of Diesel Heater to Gas Heater Diesel LPG Gas LPG Gas KW 43 70 120 Fuel consumption/hr 3 5.1 8.8 Heat output 37000 60000 100000 Cost of fuel/lit or

More information

Heating, Air Conditioning, Ventilation. Отопление-Кондиционеры-Вентиляция. MTM 8-30 kw UNIVERSAL OIL HEATER OPERATING MANUAL

Heating, Air Conditioning, Ventilation. Отопление-Кондиционеры-Вентиляция. MTM 8-30 kw UNIVERSAL OIL HEATER OPERATING MANUAL Heating, Air Conditioning, Ventilation Отопление-Кондиционеры-Вентиляция MTM 8-30 kw UNIVERSAL OIL HEATER OPERATING MANUAL 1. Usage MTM 8-30 universal oil heater is designed for heating commercial rooms

More information

Light oil burners. One stage operation

Light oil burners. One stage operation Installation, use and maintenance instructions Light oil burners One stage operation CODE MODEL TYPE 3505 RDB CF 38 50 T3 350050 RDBR CF 6 50 TR 35050 RDBR CF 33 50 TR 35050 RDBR CF 38 50 T3R 350650 RDBR

More information

Parts Available from

Parts Available from Montage und Bedienungsanleitung Manuel d entretien Installation, use and maintenance instructions Installatie-, gebruiks- en onderhoudsvoorschriften Oδηγίες εγκατάστασης, χρήσης και συντήρησης D F GB NL

More information

Installation and maintenance manual

Installation and maintenance manual Installation and maintenance manual Warm air heater WS/WO (Copy of the original version) Wolf GmbH D-84048 Mainburg Postfach 1380 Telefon +498751/74-0 Telefax +498751/741600 Internet: www.wolf-heiztechnik.de

More information

Oil burners Brûleurs fioul Stookoliebranders

Oil burners Brûleurs fioul Stookoliebranders Installation, use and maintenance instructions Manuel d entretien Installatie-, gebruiks- en onderhoudsvoorschriften GB F NL Oil burners Brûleurs fioul Stookoliebranders One stage operation Fonctionnement

More information

INLINE СENTRIFUGAL FAN BOX BOX-R OPERATION MANUAL

INLINE СENTRIFUGAL FAN BOX BOX-R OPERATION MANUAL INLINE СENTRIFUGAL FAN BOX BOX-R OPERATION MANUAL CONTENT 3 Introduction 3 General 3 Safety rules 3 Storage and transportation rules 3 Manufacturer s warranty 4 Fan design 4 Delivery set 5 Technical data

More information

MOBILE HOT AIR HEATING SYSTEMS

MOBILE HOT AIR HEATING SYSTEMS MOBILE HOT AIR HEATING SYSTEMS Issue 2012 Mobile hot air heating systems Mobile Heaters Heating Centers Quality with systems RAPID HEAT ADAPTED TO YOUR NEEDS Hot air heating systems for air, to feel good,

More information

Installation & Maintenance Manual

Installation & Maintenance Manual Installation & Maintenance Manual MOL 200 S1L (B30A) Oil Burner 11/12 Tel: +44 (0) 1905 794331 Fax: +44 (0) 1905 794017 Email: info@nu-way.co.uk Web: www.nu-way.co.uk DESCRIPTION COMPONENTS 1. Shrouded

More information

User Manual GV25 GV35 GV702. Company information: Original instructions GV12066 (1)

User Manual GV25 GV35 GV702. Company information:   Original instructions GV12066 (1) User Manual Original instructions GV25 GV35 GV702 Company information: www.vipercleaning.eu info-eu@vipercleaning.com GV12066 (1) 2012-04-10 USER MANUAL ENGLISH TABLE OF CONTENTS Introduction... 4 Manual

More information

REMKO AMT 60-E - 90-E Mobile Dehumidifier

REMKO AMT 60-E - 90-E Mobile Dehumidifier REMKO AMT 60-E - 90-E Mobile Dehumidifier Operation Technology Spare Parts Edition GB M02 REMKO powerful like a bear. Operating Instructions Make sure to read these instructions carefully before starting/using

More information

INSTALLATION, OPERATION AND MAINTENANCE. Ariterm Hybrid 20

INSTALLATION, OPERATION AND MAINTENANCE. Ariterm Hybrid 20 INSTALLATION, OPERATION AND MAINTENANCE Ariterm Hybrid 20 TABLE OF CONTENTS General...3 Installation... 4-5 Dimensions - with flue gas exhauster...6 Dimensions - without flue gas exhauster...7 Pipe installations...8

More information

JUMBO INDIRECT FIRED DIESEL HEATER OPERATING INSTRUCTIONS

JUMBO INDIRECT FIRED DIESEL HEATER OPERATING INSTRUCTIONS JUMBO INDIRECT FIRED DIESEL HEATER OPERATING INSTRUCTIONS Before using the heater, read and understand all instructions and follow them carefully. The manufacturer is not responsible for damages to goods

More information

Light oil / kerosene burner

Light oil / kerosene burner Installation, use and maintenance instructions Light oil / kerosene burner One stage operation CODE MODEL TYPE 374445 G5 444T50 290238 (5) - 05/20 TECHNICAL DATA Thermal power output 28 60 kw 2.3 5 kg/h

More information

IDE 20 D / IDE 30 D / IDE 50 D / IDE 60 D / IDE 100 D

IDE 20 D / IDE 30 D / IDE 50 D / IDE 60 D / IDE 100 D IDE 20 D / IDE 30 D / IDE 50 D / IDE 60 D / IDE 100 D EN OPERATING MANUAL OIL HEATER TRT-BA-IDE20D-30D-50D-60D-100D-TC-001-EN Table of contents Notes regarding the operating manual... 1 Safety... 2 Information

More information

infrared paraffin / kerosene / diesel heater

infrared paraffin / kerosene / diesel heater instructions for infrared paraffin / kerosene / diesel heater model no: IR20.V3 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

More information

Operating Instructions

Operating Instructions Operating Instructions P4 Pellet 8-60 Read and follow the operating instructions and safety information. Subject to technical change. July 2009 Fröling Heizkessel- und Behälterbau Ges.m.b.H, Industriestrasse

More information

Operating instructions

Operating instructions Operating instructions (Translation of the original operating instructions) Type TEKA FILTERCUBE-MV TEKA Absaug- und Entsorgungstechnologie GmbH Industriestraße 13 D-46342 Velen Postfach 1137 D-46334 Velen

More information

TTK 75 ECO OPERATING MANUAL DEHUMIDIFIER TRT-BA-TTK75ECO-TC-002-EN

TTK 75 ECO OPERATING MANUAL DEHUMIDIFIER TRT-BA-TTK75ECO-TC-002-EN TTK 75 ECO EN OPERATING MANUAL DEHUMIDIFIER TRT-BA-TTK75ECO-TC-002-EN Table of contents Notes regarding the operating manual... 01 Information about the device... 02 Safety... 04 Transport...05 Start-up...05

More information

Trumatic E. Trumatic E 2400 (Australia) Operating instructions Page 4 Installation instructions Page 7. To be kept in the vehicle!

Trumatic E. Trumatic E 2400 (Australia) Operating instructions Page 4 Installation instructions Page 7. To be kept in the vehicle! Trumatic E 7 7 2 9 9 4 Trumatic E 2400 (Australia) Operating instructions Page 4 Installation instructions Page 7 To be kept in the vehicle! Trumatic E 2400 (Australia) Table of contents Installation example...

More information

1. GENERAL SAFETY RULES

1. GENERAL SAFETY RULES ID180 & ID290 Indirect-Fired Diesel/Oil Construction Heaters Sure Flame Products Lethbridge, Alberta, Canada Telephone: (403)328-5353 Fax: (403)328-9956 www.sureflame.ca July 12, 2006 Service and Maintenance

More information

HEAT RECOVERY AIR HANDLING UNIT

HEAT RECOVERY AIR HANDLING UNIT HEAT RECOVERY AIR HANDLING UNIT OPERATION MANUAL KOMFORT_L v2(2)_en.indd 1 07.08.2015 15:0:44 CONTENTS Introduction General Safety regulations Transportation and storage regulations Manufacturer's warranty

More information

TTV 4500 / TTV 4500 HP / TTV 7000

TTV 4500 / TTV 4500 HP / TTV 7000 TTV 4500 / TTV 4500 HP / TTV 7000 EN OPERATING MANUAL AXIAL FAN TRT-BA-TTV4500-4500HP-7000-TC-003-EN Table of contents The current version of the operating manual can be found at: Notes regarding the operating

More information

SOUND-INSULATED FAN. Iso-K OPERATION MANUAL. Iso-K_v.1(2)-EN.indd :20:59

SOUND-INSULATED FAN. Iso-K OPERATION MANUAL. Iso-K_v.1(2)-EN.indd :20:59 SOUND-INSULATED FAN OPERATION MANUAL _v.1(2)-en.indd 1 10.08.2015 15:20:59 CONTENT Introduction 3 General 3 Safety rules 3 Transport and storage requirements 3 Manufacturer's warranty 3 Fan design 4 Delivery

More information

Waste water ejection unit

Waste water ejection unit Waste water ejection unit Over ground box SWH 500/50-80 SWH 500/50-80 Operation manual Table of contents: Page Declaration of conformity... 3 1. General... 4 1.1 Introduction... 4 1.2 Enquiries and orders...

More information

Silencer Preheater unit Electric post-heating unit Water circulated post-heating unit CO 2 sensor %RH sensor Pressure difference switch LON converter

Silencer Preheater unit Electric post-heating unit Water circulated post-heating unit CO 2 sensor %RH sensor Pressure difference switch LON converter VALLOX Product Code: 3158400 L 3158410 R SILENCER (OPTIONAL) INSTRUCTIONS FOR USE AND MAINTENANCE WATER CIRCULATED POST-HEATING UNIT (OPTIONAL) ELECTRIC POST-HEATING UNIT (OPTIONAL)) PREHEATER (OPTIONAL)

More information

R Series B & T2 Model

R Series B & T2 Model FRONT R Series B & T2 Model Fan Forced Wall Heaters 4-1/4 (108mm) NOTE: Knockouts in top same dimensions 3-1/4 3-1/4 (108mm) (108mm) as bottom 16-7/8 (429mm) 13-7/8 (352mm) BOTTOM 13-7/8 (352mm) 7-3/4

More information

Providing sustainable energy solutions worldwide. Installation- and maintenance instruction B 30 A

Providing sustainable energy solutions worldwide. Installation- and maintenance instruction B 30 A 178 038 51-2 2016-07-08 Providing sustainable energy solutions worldwide Installation- and maintenance instruction B 30 A DESCRIPTION Components 1. Shrouded disc 2. Nozzle 3. Ignition electrodes 4. Nozzle

More information

Operating Instructions

Operating Instructions Operating Instructions BA-003 Read and understand this manual before use. Keep this manual for future reference. CONFORMS TO UL STD.No.1017 Certified to CSA STD C22.2 No.243-10 For questions or concerns

More information

Tornado Operations & Maintenance Manual

Tornado Operations & Maintenance Manual TORNADO INDUSTRIES 7401 W. LAWRENCE AVENUE CHICAGO, IL 60706 (708) 867-5100 FAX (708) 867-6968 www.tornadovac.com Tornado Operations & Maintenance Manual MODEL NO. 99690 BD 22/14, 99720 BD 26/14 L9722

More information

Operating Manual JuniorPower

Operating Manual JuniorPower To be read completely before start-up! Operating Manual JuniorPower 12/04 von Oertzen GmbH Ferdinand-Harten-Str. 10 22949 Ammersbek Tel. +49 40 604110 Fax +49 40 6041149 www.oertzen-gmbh.de info@oertzen-gmbh.de

More information

VETO CLEANER 500 FLUE GAS CLEANER

VETO CLEANER 500 FLUE GAS CLEANER As of serial number 3100 0001 VETO CLEANER 500 FLUE GAS CLEANER USER MANUAL SPARE PARTS LIST Manufacturer: ALA TALKKARI Veljekset Ala-Talkkari Oy FI-62130 HELLANMAA TEL. +358 6 433 6333 FAX +358 6 437

More information

USER S MANUAL. Heat Recovery Ventilator. Vents Brig HRV 200 Vents Brig HRV 300

USER S MANUAL. Heat Recovery Ventilator. Vents Brig HRV 200 Vents Brig HRV 300 USER S MANUAL Heat Recovery Ventilator Vents Brig HRV 200 Vents Brig HRV 300 2 Brig HRV 200 (300) CONTENT Introduction... 3 Application... 3 Delivery set... 3 Unit designation key... 4 Basic unit dimensions...

More information

REMKO ETF 240 Portable Air Dehumidifier

REMKO ETF 240 Portable Air Dehumidifier REMKO ETF 240 Portable Air Dehumidifier Operation Technology Spare Parts Edition GB P10 REMKO powerful like a bear. Operating Instructions Read these instructions carefully before setting up/operating

More information

Operation Manual 322 KL

Operation Manual 322 KL Operation Manual 322 KL 8/07 von Oertzen GmbH Ferdinand-Harten-Str. 10 22949 Ammersbek Tel. +49 40 604110 Fax +49 40 6041149 www.oertzen-gmbh.de info@oertzen-gmbh.de Table of Content 1. Introduction Page

More information

AirUnit. Operating manual. mfh systems modern floor heating. Decentralised domestic ventilation

AirUnit. Operating manual. mfh systems modern floor heating. Decentralised domestic ventilation mfh systems modern floor heating AirUnit Decentralised domestic ventilation Operating manual List of contents, Operating manual Page 1. General information... 02 2. Device description... 03 3. Adjustment

More information

Light oil - kerosene burner

Light oil - kerosene burner Installation, use and maintenance instructions Light oil - kerosene burner One stage operation CODE MODEL TYPE 374374 G3B 437T 90 (4) - 05/0 TECHNICAL FEATURES TYPE 437T Thermal power output 9 35 kw.6

More information

PARAFFIN/DIESEL HEATERS

PARAFFIN/DIESEL HEATERS INSTRUCTIONS FOR: PARAFFIN/DIESEL HEATERS Models: AB602, AB902, AB801, AB80, AB100X & AB160X Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according

More information

Silent TS. Nr / Ideas for dental technology / A. Made in Germany

Silent TS. Nr / Ideas for dental technology / A. Made in Germany Silent TS Nr. 2921-0050 / 2921-1050 21-9191 30102012 / A Made in Germany Ideas for dental technology 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Silent TS Nr. 2921-0050

More information

INFRARED PARAFfIN / KEROSENE / model No: ir20.v2 1. SAFETY INSTRUCTIONS RECOMMENDED FUSE RATING: 5AMP

INFRARED PARAFfIN / KEROSENE / model No: ir20.v2 1. SAFETY INSTRUCTIONS RECOMMENDED FUSE RATING: 5AMP InstructioNS for: INFRARED PARAFfIN / KEROSENE / diesel HEATER model No: ir20.v2 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these

More information

TermEfekt USER S MANUAL AIR HEATER. Model PGA 14

TermEfekt USER S MANUAL AIR HEATER. Model PGA 14 Przedsiębiorstwo Produkcyjno-Wdrożeniowe ARAJ sp. z o.o. 55-080 Kąty Wrocławskie, ul. Mireckiego 30 POLAND USER S MANUAL AIR HEATER TermEfekt Model PGA 14 Kąty Wrocławskie, 2004 Product identification

More information

Specifications. Vacuum motor power consumption(w/hp) 1200 / 1.6. Exhaust water pump power consumption(w/hp 800 / 1.1

Specifications. Vacuum motor power consumption(w/hp) 1200 / 1.6. Exhaust water pump power consumption(w/hp 800 / 1.1 Specifications Rated voltage (V) AC 110-120V or 220-240V / 50-60Hz Vacuum motor power consumption(w/hp) 1200 / 1.6 Exhaust water pump power consumption(w/hp 800 / 1.1 Exhaust water pump flow (GPH/LPH)

More information

Part No KEMPER Filter-Master XL

Part No KEMPER Filter-Master XL Part No. 150 0492 KEMPER Filter-Master XL 1. Application and Mode of Operation.... 2 2. Safety Instructions......... 2 3. Placing into Operation...... 3 4. Operation Elements and Function... 3-4 5. Installation

More information

Infrared Diesel Heater

Infrared Diesel Heater Infrared Diesel Heater Model No: IRD40 PART NO: 6920415 OPERATING & MAINTENANCE INSTRUCTIONS GC0812 INTRODUCTION Thank you for purchasing this CLARKE Diesel Infrared Heater. Before attempting to use the

More information

model No: ir20.v2 FUSE

model No: ir20.v2 FUSE InstructioNS for: model No: ir20.v2 INFRARED PARAFfIN / KEROSENE / diesel HEATER 70000Btu 230V Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according

More information

JASOPELS ROTATING FLESHING MACHINE 1-BEAM

JASOPELS ROTATING FLESHING MACHINE 1-BEAM USER MANUAL JASOPELS ROTATING FLESHING MACHINE 1-BEAM ITEM NO. 32200067 Our quality Your choice 2 www.jasopels.com TABLE OF CONTENTS About this document... 3 Declaration of Conformity... 6 Safety... 6

More information

SMHA Hatch High temperature fan HT-fan Installation and Maintenance

SMHA Hatch High temperature fan HT-fan Installation and Maintenance High temperature fan HT-fan Installation and Maintenance 22.8.2012 Contents 1. Important information 2. Safety notes 3. Technical description 4. Transport 5. Mounting instructions 6. Commissioning 7. Maintenance

More information

Operating Instructions. Accessory Units Melitta Cafina XT Series. Melitta Professional Coffee Solutions

Operating Instructions. Accessory Units Melitta Cafina XT Series. Melitta Professional Coffee Solutions Operating Instructions Accessory Units Melitta Cafina XT Series Melitta Professional Coffee Solutions Contents General... 4. Manufacturer information... 4.2 About these instructions... 4.3 Explanation

More information

REMKO ETF 220 Portable Air Dehumidifier

REMKO ETF 220 Portable Air Dehumidifier REMKO ETF 220 Portable Air Dehumidifier Operation Technology Spare Parts Edition GB P04 REMKO powerful like a bear. Operating Instructions Read these instructions carefully before setting up/operating

More information

AXIS-QA G TUBO-M/MZ AXIAL FANS. Axis / Tubo OPERATION MANUAL

AXIS-QA G TUBO-M/MZ AXIAL FANS. Axis / Tubo OPERATION MANUAL TUBO-M/MZ AXIS-QA AXIS-Q TUBO-F AXIS-QR AXIS-F AXIS-QRA AXIS-QA G AXIAL FANS EN OPERATION MANUAL www.blaubergventilatoren.de CONTENT 3 Introduction 3 General 3 Safety rules 3 Transport and storage requirements

More information

KITCHEN EXHAUST FAN GLEC-6 INSTALLATION AND MAINTENANCE

KITCHEN EXHAUST FAN GLEC-6 INSTALLATION AND MAINTENANCE KITCHEN EXHAUST FAN GLEC-6 INSTALLATION AND MAINTENANCE 2 GLEC-6 - Installation and maintenance CONTENTS 1 Important information... 3 2 Safety notes... 3 3 Technical description...4 4 Transport... 6 5

More information

STEAM WALLPAPER STRIPPER MODEL HTW5

STEAM WALLPAPER STRIPPER MODEL HTW5 STEAM WALLPAPER STRIPPER MODEL HTW5 From Serial Number 75154 (110 Volt North America only) OWNERS MANUAL & OPERATING INSTRUCTIONS 2016/11 Hiretech Part # 007717 WARNING For safe operation of this machine,

More information

INLINE CENTRIFUGAL FAN. Centro-M OPERATION MANUAL

INLINE CENTRIFUGAL FAN. Centro-M OPERATION MANUAL INLINE CENTRIFUGAL FAN OPERATION MANUAL www.blaubergventilatoren.de CONTENT 3 Introduction 3 General 3 Safety rules 3 Transport and storage requirements 3 Manufacturer's warranty 4 Fan design 4 Delivery

More information

K Operating Instructions. Before first use of the unit read these operating instructions and act in accordance with them.

K Operating Instructions. Before first use of the unit read these operating instructions and act in accordance with them. K 1.100 Operating Instructions Before first use of the unit read these operating instructions and act in accordance with them. www.kaercher.com/register-and-win 59651430 (10/13) Contents General information..............

More information

Operating instructions. for radial fans for use in potentially explosive atmospheres

Operating instructions. for radial fans for use in potentially explosive atmospheres Operating instructions for radial fans for use in potentially explosive Printed in Germany We reserve the right to make amendments to the details and illustrations listed as a result of further technical

More information

VIESMANN. Service instructions VITOLADENS 300-T. for contractors. Vitoladens 300-T Type VW3B Inox-Radial heat exchanger for oil fired condensing Unit

VIESMANN. Service instructions VITOLADENS 300-T. for contractors. Vitoladens 300-T Type VW3B Inox-Radial heat exchanger for oil fired condensing Unit Service instructions for contractors VIESMANN Vitoladens 300-T Type VW3B Inox-Radial heat exchanger for oil fired condensing Unit VITOLADENS 300-T 1/2007 Please keep safe. Safety instructions Safety instructions

More information

TTV 1500 / TTV 3000 OPERATING MANUAL CONVEYING FAN TRT-BA-TTV TC EN

TTV 1500 / TTV 3000 OPERATING MANUAL CONVEYING FAN TRT-BA-TTV TC EN TTV 1500 / TTV 3000 EN OPERATING MANUAL CONVEYING FAN TRT-BA-TTV1500-3000-TC2016-26-004-EN Table of contents Notes regarding the operating manual... 2 You can download the current version of the operating

More information

CENTRIFUGAL FAN IN SCROLL CASING. Helix S-Vent OPERATION MANUAL

CENTRIFUGAL FAN IN SCROLL CASING. Helix S-Vent OPERATION MANUAL CENTRIFUGAL FAN IN SCROLL CASING Helix S-Vent EN OPERATION MANUAL Helix / S-Vent www.blaubergventilatoren.de CONTENTS CONTENTS 3 Introduction 3 Use 3 Delivery set 4 Technical data 10 Safety requirements

More information

FLAME115 INFRARED HEATER SERVICE MANUAL INDEX FIRE 115 WARNING

FLAME115 INFRARED HEATER SERVICE MANUAL INDEX FIRE 115 WARNING FLAME115 INFRARED HEATER SERVICE MANUAL INDEX 1. CONTROLS AND COMPONENTS 2. FLAME CONTROL CYCLES 3. MAINTENANCE SCHEDULE 4. TROUBLESHOOTING GUIDE 5. REPAIR PROCEDURES 1. FAN MOTOR ASSEMBLY 2. FUEL FILTER

More information

Installation and assembly instructions. for standard configuration radial blowers

Installation and assembly instructions. for standard configuration radial blowers Installation and assembly instructions for standard configuration radial blowers 001_KL01_01 Printed in Germany We reserve the right to change the information and illustrations shown in this operating

More information

Manual. Above-counter dispenser for hot drinks OTHG /12

Manual. Above-counter dispenser for hot drinks OTHG /12 Manual Above-counter dispenser for hot drinks OTHG 105 1 It is in your own interests to observe all the hazard and safety information. This helps you to prevent accidents and technical malfunctions. Only

More information

SIME FORMAT WALL HUNG BOILERS MODEL 34i AND MODEL 34e. cod A

SIME FORMAT WALL HUNG BOILERS MODEL 34i AND MODEL 34e. cod A cod. 6272262A GENERAL DATA Heating Data Heat Output Input (Adjustable) (Adjustable) Format 34i 11.2 34KW 45 145MJ/hr Format 34e 11.2 34KW 45 145MJ/hr General Specifications FORMAT 34i 34e Main burner injectors

More information

Corn Flame Energy Corn Stove Model 3000

Corn Flame Energy Corn Stove Model 3000 Corn Flame Energy Corn Stove Model 3000 Installation and Operation Guide Read thoroughly before starting installation Save this manual for future reference SAFETY NOTICE If this stove is not properly installed,

More information

51AKB / 51 AKC OWNER S MANUAL

51AKB / 51 AKC OWNER S MANUAL 51AKB / 51 AKC OWNER S MANUAL This manual applies to the following models 51AKB 009 51AKB 012 51AKC 009 51AKC 012 Read this instruction manual thoroughly before using the air conditioner. Control panel

More information

REMKO AMT 45-E to 115-E

REMKO AMT 45-E to 115-E REMKO AMT 45-E to 115-E Air dehumidifiers Operation Technology Spare parts Edition GB D09 Contents Air dehumidification 4 Safety notes 6 Intended use 7 Customer service and guarantee 7 Environmental protection

More information

Test Unit GTL 100 for Fire Detectors

Test Unit GTL 100 for Fire Detectors Test Unit GTL 100 for Fire Detectors Description and Operation Manual Zertifiziertes QM System Nach DIN EN ISO 9001 Description and Operation Manual Table of Contents 1. Instructions 1.1 General 1.2 Standards

More information

Product Manual Glue Applicators MS 80 and MS 200

Product Manual Glue Applicators MS 80 and MS 200 Product Manual www.pakarte.com Glue Applicators MS 80 and MS 00 Translation from German to English Table of Contents Product Description General Safety Instructions Safety Measures to be taken during Operation

More information

en Direct oil-fired space heaters HD... Operator's manual

en Direct oil-fired space heaters HD... Operator's manual 0211670en 002 12.2007 Direct oil-fired space heaters HD... Operator's manual Table of contents 1. Foreword 5 2. Safety information 6 2.1 General recommendations... 6 2.2 Safety devices... 7 2.3 Labels...

More information

CE Unit is suitable for material transport. The transported gas may be up to 80 C.

CE Unit is suitable for material transport. The transported gas may be up to 80 C. The manual contains: 1 Safety regulations 1.1 Electrical 1.2 Crush risk 1.3 Hazardous dust 1.4 Suction injuries 1.5 Noise 1.6 Pneumatic 1.7 Other equipment 2 Machine Operation 3 Installation Directions

More information

30KW ELECTRIC FAN HEATER

30KW ELECTRIC FAN HEATER 30KW ELECTRIC FAN HEATER MODEL NO: DEVIL 7030 PART NO: 6935458 OPERATION & MAINTENANCE INSTRUCTIONS LS0615 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product,

More information

ST 40 Oil Burner. Installation & Maintenance Manual

ST 40 Oil Burner. Installation & Maintenance Manual ST 40 Oil Burner Installation & Maintenance Manual 178 093 13 Thank you for choosing a Nu-way burner. As you would expect from a Company who has a pedigree of more than 75 years in the heating industry,

More information

OPERATION AND MONTAGE MANUAL ROOF FANS

OPERATION AND MONTAGE MANUAL ROOF FANS NO RFEC/U/2017-1 (EN) (valid since 18.08.2017) ROOF FANS RF/EC...-... / RFV/EC...-... Venture Industries Sp. z o.o. is not responsible for any damage caused by improper use of the fan and reserves the

More information

Providing sustainable energy solutions worldwide. Installation- and maintenance instruction B 10 E R

Providing sustainable energy solutions worldwide. Installation- and maintenance instruction B 10 E R 178 013 03-2 2016-05-26 Providing sustainable energy solutions worldwide Installation- and maintenance instruction B 10 E R DESCRIPTION Components 1. Scale, nozzle assembly 2. Nozzle assembly adjustment

More information

UV Flame Supervision System

UV Flame Supervision System 7 783 UV Flame Supervision System DETACTOGYR LFE50 Series 02 ISO 9001 The LFE50 is a self-checking UV flame supervision system designed for use with continuously operating burners or for burners running

More information

Indirect gas-fired air heater

Indirect gas-fired air heater Indirect gas-fired air heater SERIES HD INSTALLATION AND SERVICE MANUAL MANUFACTURED BY : BROTHERS LIMITED WARNING Improper installation, modification, adjustment or maintenance may cause damage, injury

More information

USER S MANUAL. VCU/VCUN Series CENTRIFUGAL FAN IN SCROLL CASING

USER S MANUAL. VCU/VCUN Series CENTRIFUGAL FAN IN SCROLL CASING USER S MANUAL VCU/ Series CENTRIFUGAL FAN IN SCROLL CASING 2 CONTENTS Introduction Use Delivery set Designation key Technical data Safety requirements Design and operating logic Mounting and set-up Connection

More information

Operating Instructions

Operating Instructions Operating Instructions TEKA Cartmaster Type PF-W 1, PF-W 2 TEKA Absaug- und Entsorgungstechnologie GmbH Industriestraße 13 D-46342 Velen Postfach 1137 D-46334 Velen Tel.: +49 (0) 2863 9282-0 Fax: +49 (0)

More information

Trotec PAC FT 2600 Portable air conditioner

Trotec PAC FT 2600 Portable air conditioner Trotec PAC FT 2600 Portable air conditioner The PAC FT 2600 portable room air conditioner comes with an infrared remote control and an air outlet hose with a flat nozzle.the unit s primary function is

More information

SERVICE AND INSTALLATION MANUAL MODELS HDO(H) OIL FOR YOUR SAFETY

SERVICE AND INSTALLATION MANUAL MODELS HDO(H) OIL FOR YOUR SAFETY Bousquet Technologies Inc. 2121, Nobel, Ste Julie, Quebec, Canada, J3E1Z9 SERVICE AND INSTALLATION MANUAL MODELS HDO(H) OIL Oil-Fired air heater for industrial and commercial use. FOR YOUR SAFETY Do not

More information

Combi 2 E / 4 E CP plus (Australia) Operating instructions Page 2. To be kept in the vehicle!

Combi 2 E / 4 E CP plus (Australia) Operating instructions Page 2. To be kept in the vehicle! Combi 2 E / 4 E CP plus (Australia) Operating instructions Page 2 To be kept in the vehicle! Combi 2 E / 4 E CP plus (Australia) 4 5 1 2 6 10 13 15 16 12 8 10 14 6 1 Control panel (digital) 2 Room temperature

More information

User s Manual RA-3030SS RA-3036SS. NOTE: This unit was designed for indoor residential use and DUCTED operation only.

User s Manual RA-3030SS RA-3036SS. NOTE: This unit was designed for indoor residential use and DUCTED operation only. www.windsterhood.com User s Manual UNDER CABINET SERIES RA-3030SS RA-3036SS NOTE: This unit was designed for indoor residential use and DUCTED operation only. DO NOT USE OVER A WOOD GRILL OR MOUNT OUTDOOR

More information

ExDetector IRCO2. ExDetector IRHC. Operating and Installation Instructions. Gas Detection and Warning Systems

ExDetector IRCO2. ExDetector IRHC. Operating and Installation Instructions. Gas Detection and Warning Systems IRCO2 IRHC Operating and Installation Instructions Gas Detection and Warning Systems Important Instructions Prerequisites for safe and reliable operation of the system: Appropriate transport and handling

More information

User s Manual WS-69TB30 / WS-69TB36 (22 ) WS-69TB42 / WS-69TB48 (22 ) WS-69TS30 / WS-69TS36 (18 ) WS-69TS42 / WS-69TS48 (18 )

User s Manual WS-69TB30 / WS-69TB36 (22 ) WS-69TB42 / WS-69TB48 (22 ) WS-69TS30 / WS-69TS36 (18 ) WS-69TS42 / WS-69TS48 (18 ) www.windsterhood.com User s Manual LINER SERIES WS-69TB30 / WS-69TB36 (22 ) WS-69TB42 / WS-69TB48 (22 ) WS-69TS30 / WS-69TS36 (18 ) WS-69TS42 / WS-69TS48 (18 ) NOTE: PLEASE INSPECT HOOD IMMEDIATELY UPON

More information

15KW ELECTRIC FAN HEATER

15KW ELECTRIC FAN HEATER 15KW ELECTRIC FAN HEATER MODEL NO: DEVIL 7015 PART NO: 6935456 OPERATION & MAINTENANCE INSTRUCTIONS LS0615 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product,

More information

and Installation Instructions The installation instructions for the Unit pressure jet oil burner is included in the pressure jet oil burner pack.

and Installation Instructions The installation instructions for the Unit pressure jet oil burner is included in the pressure jet oil burner pack. Technical Guide and Installation Instructions MKS / MUS Steel boiler 70-550 kw The installation instructions for the Unit pressure jet oil burner is included in the pressure jet oil burner pack. The control

More information

Operating Instructions

Operating Instructions Operating Instructions Varioset Standard After-sales service For after-sales service please contact the Veit representative in your country. GmbH & Co. Justus - von - Liebig - Str. 15 D - 86899 Landsberg

More information

AXIAL FANS USER S MANUAL

AXIAL FANS USER S MANUAL AXIAL FANS USER S MANUAL WARNING! Disconnect the fan from power supply prior to any connection, servicing and repair operations. Only duly qualified electricians with valid electrical permit for electric

More information

INSTRUCTION MANUAL FOR OIL BURNER MODELS

INSTRUCTION MANUAL FOR OIL BURNER MODELS INSTRUCTION MANUAL FOR OIL BURNER MODELS X400 Bio B10 E90-803-001-001-03 Rev 13-1 - Contents Technical specifications Technical data... 3 Working field... 3 Dimensions... 4 Head and electrode settings...

More information

Kyung Dong Oil Boiler. Contents. 1. General Warnings Safety Warnings

Kyung Dong Oil Boiler. Contents. 1. General Warnings Safety Warnings Contents 1. General Warnings --------------------- 1 2. Safety Warnings ----------------------- 2 3. Parts and structure --------------------- 7 4. Safety Device ------------------------- 9 5. Checkups

More information

THERMOFILM CONVECTIVE PANEL HEATER INSTALLATION, OPERATION AND MAINTENANCE MANUAL. Models: CP 2400 CP 2000 CP 1500 CP 1000 TABLE OF CONTENTS

THERMOFILM CONVECTIVE PANEL HEATER INSTALLATION, OPERATION AND MAINTENANCE MANUAL. Models: CP 2400 CP 2000 CP 1500 CP 1000 TABLE OF CONTENTS THERMOFILM CONVECTIVE PANEL HEATER Rev C JUL13 INSTALLATION, OPERATION AND MAINTENANCE MANUAL Models: CP 2400 CP 2000 CP 1500 CP 1000 TABLE OF CONTENTS 1. Important Safety Instructions 2. Specification

More information

OPERATING & MAINTENANCE MANUAL INDUSTRIAL DIRECT FIRED DIESEL/KEROSENE HEATERS IC 25

OPERATING & MAINTENANCE MANUAL INDUSTRIAL DIRECT FIRED DIESEL/KEROSENE HEATERS IC 25 OPERATING & MAINTENANCE MANUAL INDUSTRIAL DIRECT FIRED DIESEL/KEROSENE HEATERS IC 25 NOT FOR DOMESTIC USE SPACE HEATING ONLY Made By: Spitwater Australia Pty Ltd 953 Metry St North Albury, NSW, Australia

More information

DIESEL/PARAFFIN HEATERS

DIESEL/PARAFFIN HEATERS DIESEL/PARAFFIN HEATERS MODEL NO: XR80, XR110, XR160, XR210 PART NO: 6931004, 6931006, 6931008, 6931012 OPERATION & MAINTENANCE INSTRUCTIONS LS0814 INTRODUCTION Thank you for purchasing this CLARKE product.

More information

User s Manual WS-4830SS WS-4836SS NOTE: PLEASE INSPECT HOOD IMMEDIATELY UPON RECEIVING. CLAIM OF DAMAGE AFTER 7 DAYS OF DELIVERY WILL BE DENIED.

User s Manual WS-4830SS WS-4836SS NOTE: PLEASE INSPECT HOOD IMMEDIATELY UPON RECEIVING. CLAIM OF DAMAGE AFTER 7 DAYS OF DELIVERY WILL BE DENIED. www.windsterhood.com User s Manual UNDER CABINET SERIES WS-4830SS WS-4836SS NOTE: PLEASE INSPECT HOOD IMMEDIATELY UPON RECEIVING. CLAIM OF DAMAGE AFTER 7 DAYS OF DELIVERY WILL BE DENIED. This unit is designed

More information

Operating Manual. VIENNA Hot Display

Operating Manual. VIENNA Hot Display Operating Manual VIENNA Hot Display Operating and Maintenance instructions Please read this manual carefully before you start to operate your heated display case. Following these instructions helps you

More information