SERVICE MANUAL WASHING MACHINE MODEL : WD-3243RHD WD-3245RHD CAUTION. Website:

Transcription

1 Website: WASHING MACHINE SERVICE MANUAL CAUTION READ THIS MANUAL CAREFULLY TO DIAGSE TROUBLECORRECTLY BEFORE OFFERING SERVICE. MODEL : WD-3243RHD WD-3245RHD

2 JUL PRINTED IN KOREA P/No.:3828ER3008S

3 CONTENTS 1. SPECIFICATION FEATURES & TECHNICAL EXPLANATION PARTS IDENTIFICATION INSTALLATION OPERATION WIRING DIAGRAM / PROGRAM CHART TROUBLESHOOTING BEFORE PERFORMING SERVICE QC TEST MODE HOW TO KW THE WATER LEVEL FREQUENCY ERROR DISPLAY ERROR DIAGSIS AND CHECK LIST DIAGSIS AND ANSWER FOR ABRMAL OPERATION FAULT DIAGSIS AND TROUBLESHOOTING DISASSEMBLY INSTRUCTIONS EXPLODED VIEW AND PARTS LIST THE EXPLODED VIEW OF CABINET ASSEMBLY THE EXPLODED VIEW OF CONTROL PANEL AND DISPENSER ASSEMBLY THE EXPLODED VIEW OF DRUM AND TUB ASSEMBLY THE EXPLODED VIEW OF DRYER...42 APPENDIX (Replacement parts list)

4 1. SPECIFICATION ITEM WD-3243RHD/WD-3245RHD POWER SUPPLY PRODUCT WEIGHT WASHING ELECTRICITY SPIN CONSUMPTION FAN MOTOR DRAIN MOTOR WASH HEATER DRY HEATER REVOLUTION WASH SPEED SPIN OPERATION WATER PRESSURE CONTROL TYPE WASH CAPACITY DRY CAPACITY3.0kg V~ 60Hz / 2 lbs. (71 kg) 140W 300W 25W 40W 1000W 1200W 45rpm No spin/400/600/800/1000/1200 rpm 4.5 ~ 145 PSI (30 ~ 1000 KPa) Electronic 14 1 / 2 lbs. 6.5 kg 6 5 / 8 lbs. 3.0 kg DIMENSION mm WASH PROGRAM OPTION DOOR SWITCH TYPE WATER LEVEL RESERVATION SENSING OF THE LAUNDRY AMOUNT FUZZY LOGIC DISPLAY OF THE REMAINING TIME ERROR DIAGSIS POWER AUTO OFF CHILD LOCK AUTO RESTART RAPID Cotton, Permant Press, Quick, Delicate, Wool, Rinse+Spin Extra Wash, Rinse Pluse Automatic type by pressing Door Open botton 8 steps (by sensor) From 3 hours to 19 hours Adapted Adapted Adapted 10 items Adapted Adapted Adapted Adapted 3

5 2. FEATURES & TECHNICAL EXPLANATION 2-1.FEATURES Automatic process from washing to drying. Automatic process from washing to drying can be selected easily. Washing capacity : 14 1 / 2 lbs. 6.5 kg Drying capacity : 6 5 / 8 lbs. 3.0 kg More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption. Direct Drive system The advanced Brushless DC motor rotates the Drum directly without belt and pulley. TEMP. TIME DELAY Child-Lock The Child-Lock system has been developed to prevent children from pressing any button to change the program during operation. Low noise speed control system By sensing the amount of load and balance, automaticaly distributes load evenly to minimize the spinning noise level. Auto Restart Although the washing machine is turned off by a power failure, it restarts automatically where it stopped when power is supplied again. And it will be the same if the machine unplugged and is plugged in again. 4

6 2-2.DETERMINE WASHING TIME BY FUZZY LOGIC To get the best washing performance optimal time is determined by sensing of water temperature, selected washing temperature and laundry amount. water temperature washing time selected washing temperature FUZZY LOGIC rinsing time the best washing performance laundry amount spin rhythm, time SENSING PROCESSING DETERMINATION EFFECT 2-3.WATER LEVEL CONTROL This model adopts a pressure sensor which can sense the water level in the tub. Water supply is stopped when the water level to the preset level, then the washing program proceeds. Spinning does not proceed until the water in the tub reduces a certain level. 2-4.CONTROL OF DOOR OPEN The door can be opened by pressing DOOR OPEN button after finishing program. When the revolution of drum is stopped and in case water leel is below level 2, door can be opened by pressing the DOOR OPEN button. If there is no power, the door can be opened by pulling the door strap. (If the water level is high, first drain the water by pulling out the hose cap) 5

7 3. PARTS IDENTIFICATION Drawer (For detergent and fabric softener) Power Plug If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or a similarly qualified person in order to avoid a hazard. Control Panel Drain Hose Door Drum Drain Pump Filter Drain Plug Lower Cover Adjustable Feet Emergency Door Release ACCESSORIES Inlet hose(1 each) Wrench 6

8 4. INSTALLATION Before servicing ask trouble the customer, what the trouble is. Check the adjustment (power supply is V~ remove the transit bolts...) Check the troubles referring to the troubleshooting. Decide service steps referring to disassembly instructions. Then, service and repair. After servicing, operate the appliance to see whether it works O K or T. STANDARD INSTALLATION The appliance should be installed as follows. REMOVE THE TRANSIT INSTALL THE APPLIANCE ADJUST THE BOLTS ON FLAT AND FIRM SURFACE HORIZONTAL Remove the transit bolts Turn the leveling feet to (3EA: ) with supplied spanner. set the appliance horizontally. Keep the transit bolts and spanner for future use. Insert the 3 caps provided into the hole Low High 1 2 The appliance goes up by rotating the feet clockwise. The appliance come down by rotating the feet counterclockwise. 7

9 HOW TO CONNECT INLET HOSE Check that the rubber washer is inside of the valve connector. Connect the inlet hose firmly to prevent leak. CONNECT DRAIN HOSE Make sure that the hose is not twisted. Avoid submerging the end of the hose. The drain hose should be placed under 100cm from the floor. CONNECT POWER PLUG Connect the power plug to the wall outlet. Avoid connecting several electric devices, It may be the cause of a fire. 8

10 TEST OPERATION Preparation for Press the POWER button. Press the Start/Pause washing. button. START PAUSE Connect the power plug to the outlet. Connect the inlet hose. In case of Cotton program. Check the water heating. Check automatic reverse Check the water supply. turn. Press the Temp. button Check if the drum rotates Check if water is supplied and the present temperature will clockwise and counterclockwise. through the detergent dispenser. be displayed. Check drain and spin Power off and open the Water removal door Turn off Wash and Rinse after pressing the Start/Pause button and start the machine again. Check drain and spin. DOOR OPEN Power off and then Power on. Check if the door can be opened by pressing Door open button. If SVC is needed during check, remove the remaining water by pulling out the hose cap. 9

11 5. OPERATION Rinse Hold If you desire to leave fabrics in the machine without spinning after rinse to prevent wrinkling. You may select rinse hold by pressing the Rinse Hold Button. To drain and spin, press Rinse Hold Button or Start/Pause button to turn off the Rinse Hold lamp. LED display Display the remaining time (Hour : Minute) to finish. In case of abnormal operation, error indications are displayed. (,,,,,, ) See trouble shooting guide. Wash program s 6 programs can be selected type of the laundry. By pressing the button, [COTTON PERM PRES WOOL DELICATE can be selected For manual option and spin Use these buttons to change washing method, rinse times, spinning speed. When lamp is off, no selection has been made. Extra wash is available for Cotton and Perm press program. EXTRA WASH RINSE PLUS SPIN RINSE HOLD AUTO TIME HEAT HOT/COLD WARM/WARM WARM/COLD COLD/COLD OPTION SPIN DRY TEMP. TIME LEFT TIME D TIME DELA Dry selector Dry programs can be selected by pressing the [DRY] button. By pressing the button, [Auto No Heat Time (30/60/90/120/150)] can be selected. Water temperature selector Press the button to select water temperature. The water temperature is selected [Warm/Cold Warm/Warm Hot/Cold Cold/Cold] during normal program. Hot/Cold is selected only for cotton program. By pressing the button during operating the washer, the present temperature is displayed. Child lock Once Child-Lock is set, and canceled by pressin [Temp.] and [Time Delay] simutaneously once C set. Once Chold Lock is set, all buttons are irope The Child-Lock system can be set at any time ev Power-Off, on Pause and operation. It is automa when an operational error occurs. When power is off, the LED indicates [ ] on During operation, or when the programme is pau the LED will indicate [ ] and the remaining t 10

12 elector depending on the S QUICK INSE+SPIN ] Door Start/Pause open button Use Pressing the button the button to start open or pause wash cycle. the door. The Only power operates turns when off automatically the in 4 power minutes plug after is connected the pause button to is pressed. AC 110V outlet. Press the button to change the program. Door open button Pressing the button open the door. Only operates when the power plug is connected to AC V outlet. ON/OFF button ELAY COTTON RINSE+SPIN INLET Press the button to turn power on and off. Y PERM PRESS QUICK PRO- GRAM DELICATE WOOL IMBALANCE DRAIN DOOR LOCK START PAUSE DOOR OPEN Door lock display It shows whether the door can be opened or not during the washing. If the lamp is on or blink, the door can not be opened. Delay finish Error display g and holding both hild lock is rable. en including during tically cancelled y. sed me. Press the button when reservation washing is needed. When the button is pressed, [ ] is displayed. A maximum delay of [ ] hours can be set. Each press advances time delay by one hour. Use ON/OFF button to cancel [Time delay]. The display blinks if there is an error. INLET : Trouble with water supply IMBALANCE : The laundry is tilted to one side. DRAIN : If the drain pump filter is clogged. 11

13 6. WIRING DIAGRAM / PROGRAM CHART Hot CYCLE W S washing Washing Pre Main drain I S W S washing heating washing drain I S W S rinse drain * Water Supply : W S / Intermittent Spin : I S / Distangle : D T Rinse Normal Rinse I S W S rinse drain I S W S rinse drain I S W S rinse Spin drain spin D T DRY (min) (min) Cotton Perm Press Quick Wool Delicate Rinse+Spin Spin Normal working Time : Basic Cycle * Basic time is minute in washing chart : Optional Cycle * The actual program time can be varied with the load amount. Pre-Setting Time : Water Supply sec. Drain - 60 sec. About 3:55 About 3:35 About 36 About 56 About 56 About 32 About 12 12

14 7. TROUBLESHOOTING 7-1.BEFORE PERFORMING SERVICE Be careful of electric shock or disconnecting the parts while trouble shooting. Voltage of each terminal in V~ and DC while applying an electric current. 7-2.QC TEST MODE. Pressing SPIN, and DRY button simultaneously. Power supply ON with pressing upper two button.then buzzer sound twice. Press the START/PAUSE button as follows. Press the START/PAUSE button more 4 times until stop spinning Pressing number of Start/Pause button None All lamps turn on Checking Point Display Status 1 time Clockwise spin (right) Drum rpm (About 40~52) 2 times Low speed Spin Drum rpm (About 70~90) 3 times High speed Spin Drum rpm (About 90~110) 4 times Inlet valve for pre-wash operation Water level frequency (25~65) 5 times Inlet valve for main-wash operation Water level frequency (25~65) 6 times Inlet valve for dry operation Water level frequency (25~65) 7 times Counterclockwise spin (left) Drum rpm (About 40~52) 8 times Heater is in operation for 3 sec. Water temperature 9 times Draining pump operation Water level frequency 10 times Dry operation for 6 minutes Auto off operation after 6 minutes 7-3.HOW TO KW THE WATER LEVEL FREQUENCY Press the SPIN and DRY button simultaneously. The digits means water level frequency (10-1 ) ex) 241 : Water level frequency = = HOW TO KW TO TEMPERATURE OF EACH THERMISTOR AT OPERATING CONDITION. Thermistor in tub : Press the [WATER TEMP] button. Thermistor in dry duct : Press the [DRY] button. Thermistor in condensing duct : Press the [SPIN] and [DRY] button simultaneously. 13

15 7-5.ERROR DISPLAY. If you press the START/PAUSE button when an error is displayed. any error except will disappear and the machine will change into pause status. In case of if the error is not resolved within 20 sec., the in case of other errors, if the error is not resolved within 4 min., power will be turned off automatically and the error code will blink. But in the case of, power will not be turned off. ERROR SYMPTOM CAUSE 1 WATER INLET ERROR INLET Not reached to the water level (2 level) within 4 minutes after water supplied or not reached to the preset water level within 25 minutes. 2 DRAIN ERROR Not fully drained within 5 minutes. 3 OVERFLOW ERROR Water is over flowing (over 8 level). If is displayed, drain pump operates to drain water automatically. 4 SENSOR PRESSURE S/W ERROR The sensor pressure switch is out of order. 5 DOOR OPEN ERROR The door does not open in spite of pressing the [DOOR OPEN] button. In case of operating the reservation function or the other function with door opened. Close the door, then the error display is resolved. The door switch is out of order. 6 IMBALANCE ERROR IMBALANCE The appliance is tilted. Laundry is gathered to one side. 7 HEATING ERROR The THERMISTOR is out of order. 14

16 ERROR SYMPTOM CAUSE 8 CURRENT ERROR MAIN PWB ASSEMBLY is out of order Replace the MAIN PWB ASSEMBLY Winding in the STATOR ASSEMBLY is short-circuited. Replace the STATOR ASSEMBLY is dispplayed during a high spin Replace the LEAD WIRE ASSEMBLY (MOTOR) 9 MOTOR ERROR The connector in the LEAD WIRE ASSEMBLY is not connected to the connnector of STATOR ASSEMBLY Reconnect or repair the connector The hall sensor is out of order/defective. Replace the STATOR ASSEMBLY 10 DRY HEATOR ERROR The Dry Heater is out of order Replace the Dry Heater The Connector of the Dry Heater is not connected properly to the connector in the Main PWB ASSEMBLY Reconnect or repair the connector The Dry fan motor is out of order Replace the fan Motor. 15

17 8. ERROR DIAGSIS AND CHECK LIST 8-1.DIAGSIS AND ANSWER FOR ABRMAL OPERATION SYMPTOM GUIDE FOR SERVICE CALL POWER Is the power plug connected firmly to V~ outlet? Power failure? or Breaker opened? Is the outlet contralled by a switch? Visit to check Water inlet trouble Is INLET displayed? INLET INLET Is the tap opened? Is the tap frozen? Is the water supply shut-off? Is filter in the inlet valve clogged with foreign material? Clean the filter of inlet valve Visit to check 16

18 SYMPTOM GUIDE FOR SERVICE CALL Door does not open Error displayed on the program Started with door opened? Close the door Didn't you press the [DOOR OPEN] button with water remained in the tub? 1. Press the [START/PAUSE] button to stop the appliance. 2. Drain water by selecting spin. 3. Open door by pressing the [DOOR OPEN] button. Isn't door opened in spite of pressing the [DOOR OPEN] button Visit to check Check if the door switch is O. K. DRAIN TROUBLE Is displayed? DRAIN DRAIN Is the debris filter clogged with foreign material such as pins, coins, etc? Clean up the filter. Is the drain hose frozen with water, kinked, or crushed? Visit to check 17

19 SYMPTOM GUIDE FOR SERVICE CALL Suds overflow from the appliance. (In this condition, wash and spin do not operate normally) Is low-sudsing detergent for the drum washing machine used? Is the proper amount of detergent used as recommended? Recommend to reduce the amount of detergent. LOW-SUDSING This appliance has the automatic suds sensing function which operates under much suds condition for good rinse and preventing overflow. When much suds are sensed, the suds removing function such as drain, water input, pause will operate without rotating the drum. No effect of softener Is softener put in the correct compartment of the drawer? Compartment for softener Is the drawer closed during wash? Is the softener cap clogged? Explain how to use softener Clean the compartment for softener Visit to check 18

20 8-2.FAULT DIAGSIS AND TROUBLE SHOOTING CAUTION 1. Be careful of electric shock or disconnecting the parts while trouble shooting. 2. First of all, check the connection of each part terminal with wiring diagram. 3. If you replace the MAIN PWB ASSEMBLY, Put in the connectors correctly. POWER When measuring the voltage of the outlet, is the voltage AC V? Check the fuse? (1) Is the led (1) on? Replace MAIN PWB ASSEMBLY PWB ASSEMBLY (MAIN) (2) Is connector (2) disconnected or disassembled? Reconnect the PWB ASSEMBLY PWB ASSEMBLY (MAIN) Is wire of the PWB ASSEMBLY disconnected? Reconnect the PWB ASSEMBLY Replace PWB ASSEMBLY 19

21 WATER SUPPLY Is water supply shut-off? Is the tap opened? When you press both RINSE button and SPIN button simultaneously, is the water level frequency below 240? Is the inlet valve filter clogged with impurity? Open the tap. Check the AIR CHAMBER and the tube clogged with impurity. Clean the filter. Is resistance between each terminal of INLET VALVE ASSEMBLY is 2~8kΩ? Replace the INLET VALVE ASSEMBLY. Check the voltage of the inlet valve connector V~. (Refer to 7-2 QC TEST MODE) Replace the MAIN PWB ASSEMBLY DETERGENT DOES T FLOW IN Is water supplied? Refer to WATER SUPPLY Wiring diagram MAIN WASH SOFTENER LIQUID BLEACH Are replaceptacles correctly connected to the terminals of the INLET VALVE ASSEMBLY? Is detergent put in the correct compartment of the drawer? Check the wiring on the dispenser. Put the detergent in the correct position LIQUID BLEACH MAIN WASH : Detergent Is the detergent caked or hardened? Clean the drawer. 20

22 max SOFTENER DOES T FLOW IN Is water supplied? Refer to WATER SUPPLY Wiring diagram Are receptacles correctly connected to the terminals of the INLET VALVE ASSEMBLY? Check the wiring on the dispenser. MAX Is softener put in the correct compartment of the drawer? Put it in the correct compartment. Is the softener cap clogged? Clean the Cap and Drawer. ABRMAL SOUND Is the motor bolt loosened? Fix the bolt tightly. Is there friction noise from the motor? Replace the STATOR ASSEMBLY or ROTOR ASSEMBLY. 21

23 HEATING WITHOUT WATER OPTION SPIN When pressing OPTION and SPIN at the same time after draining, is the water level frequency 248 ~ 262 or more? When pressing SPIN, DRY buttons at the same time while wash, is the water level frequency between ? Replace the S.PRESSURE SWITCH ASSEMBLY Checking voltage between two pins as press the POWER button is the voltage V~? Replace the MAIN PWB ASSEMBLY AC V DRAIN MALFUNCTIONING Is the drain hose twisted or frozen? Repair the DRAIN HOSE ASSEMBLY. Is the impeller of the drain pump clogged? Remove foreign material. Is the connector disconnected, disassembled? Reconnect or repair the connector (2) Is the coil of the drain pump cut-off? (resistance of coil is 80~150Ω) Repair the DRAIN PUMP ASSEMBLY. (1) When checking voltage between connectors (, )on spinning, is the voltage V~ as the figure? Repair the MAIN PWB ASSEMBLY. PWB ASSEMBLY (Main) 22

24 WASH HEATER TROUBLE When checking the voltage between connector during whites washing. is the voltage V? Replace the MAIN PWB ASSY (1) AC V YELLOW RED After power off,is the resistance of wire (RED-YELLOW) connectors between 10 ~30? Normal After power off and the heater terminal is disconnected, is the resistance 10~30? Replace the HEATER ASSEMBLY HEATING CONTINUOUSLY ABOVE THE SETTING WATER TEMPERATURE TEMP. When pressing WATER TEMP. during, is the displayed temperature is over 10ûC higher than the selected temperature? Check if inlet hose is connected to a hot faucet ; otherwise, replace PWB ASSEMBLY(Main) Is the resistance between Thermistor Comectors 2.5k ~ 180k? Replace Thermister When checking THERMISTOR on the tub is the THERMISTOR loosened above 2mm from the rubber? Push the THERMISTOR tightly to the rubber. 23

25 SPIN TROUBLE OPTION SPIN Check on the spinning, is the frequency of the water level 248 or more. The frequency can be checked by pressing the OPTION and SPIN buttons at the same time on the program. Check the S.PRESSURE SWITCH ASSEMBLY or HOSE (Pressure). If the problem is on the S.PRESSURE SWITCH ASSEMBLY or the HOSE, replace the S.PRESSURE SWITCH ASSEMBLY or the HOSE. OPTION SPIN When pressing OPTION, SPIN and POWER buttons at the same time after power off, press the START/PAUSE button 1 times, is the drum spinning at low speed? Normal Is it disconnected, or disassembled? [Red:3pin (1), NA:4pin (2)] Correct the connector. (2) (1) Check the motor connector, Is the resistance of the terminal same as the figure? MOTOR TERMINAL (1) Replace the STATOR ASSEMBLY (1) Resistance of terminal: About 5Ω 15Ω Replace the MAIN PWB ASSEMBLY Door does not open DOOR LOCK Is DOOR LOCK Display Led on? After draining and DOOR LOCK lid off, press Door open. Is Displayed? Check switch Assembly, Door lock connector and Main PWB ASSEMBLY (Blue, 3pin) 24

26 [dhe] ERROR DISPLAY Dry duct Is the resistance of 2 thermistors on condensing duct and dry duct 2.5kΩ ~ 180kΩ (at 105 C ~ 0 C) Replace the thermistor. (6322FR2046A) Condensing duct Thermistor Condensing bellows CHECK FOR DRY HEATER TROUBLE CHECK FOR DRY FAN MOTOR TROUBLE Disassemble the cabinet cover and condensing bellows. Is there any foreign object in condensing bellows. Clean the bellows Disassemble the dry fan assy and dry duct upper, and clean foreign object in duct and fan. 25

27 DRY HEATER TROUBLE After power off, is the resistance of dry heater 10 ~ 40Ω? Replace the dry heater. Is thermostat closed? Replace the thermostat. When checking voltage between connectors ( 1, 2 ) on drying, is the voltage AC V as the figure? (Wire color : 1 - Red, 2 - Blue) Replace the PWB assy (Main) 26

28 DRY FAN MOTOR TROUBLE (2) (1) Is it disconnected, or disassembled? (1) - Nature, 3pin (2) - Red 6pin Reconnect or repair connector. (1) (2) (3) When checking voltage between connectors (1)~ (2), (2) ~ (3) on drying, is the voltage DC 9~15V as the figure? Wire color : (1) - White, (2) - Blue (3) - Black Replace the PWB ASSEMBLY(Main) Check the motor connector, is the resistance of terminal same as the figure? Resistance of terminal : 1-3 : 2~5Ω 2-3 : 2~5Ω Replace the DRY FAN ASSEMBLY. 27

29 LOT OF VAPOR IN DRAWER WHEN DRYING Isn't the water supply shut-off? Is tap opened? Open the tap. Isn't the inlet valve filter clogged with impurity? Clean the filter. Is resistance of the inlet valve terminal between 2 to 8 kω? Replace the inlet valve. (5220FR2075C) Check if the voltage of each terminal of Inlet Valve is AC V. (Refer to 7.TEST MODE) Replace PWB assy (Main) (6871EC1023H) 28

30 9. DISASSEMBLY INSTRUCTIONS Disassemble and repair the parts after pulling out power cord from the outlet. CONTROL PANEL PLATE ASSY (TOP) Unscrew the screws on the top plate. The PLATE ASSEMBLY (Top) is pulled back and then upward to arrow direction. The cover (Inner) is disassembled. HOOK The PWB ASSEMBLY (Display) connectors are disconnected. Pull out drawer, three screws are unscrewed. Press two upper hooks and pull the control panel forward. PANEL ASSY (CONTROL) PWB ASSY (DISPLAY) The PWB assembly (Display) is disconnected. When 8 screws are unscrewed on the PWB insulator and the PWB assembly (Display) is disassembled from the PWB insulator. 29

31 PWB ASSEMBLY (POWER) The back cover is removed. Two screws are unscrewed. Disconnect connector from the wiring. Pull the PWB ASSEMBLY (Main) to arrow direction. DISPENSER ASSEMBLY The PLATE ASSEMBLY (Top) and the cover (lnner) are disassembled. Pull the drawer to arrow direction. Two screws are unscrewed. DRAWER The hose clamps (6EA) and the hose are disassembled. The ventilation bellows are disassembled on the tub. DISPENSER ASSEMBLY 30

32 INLET VALVE 2 1 Disconnect the wiring connector. Remove the valve by two screws of the valve holder. When reconnecting the connector 3 VALVE (DRY) VALVE (LIQUID BLEACH) VALVE (RMAL-WASH) VALVE (HOT) YL/BK - BK GY/WH - BK WH/BK - BK BL/RD - BK COVER LOWER Remove the lower cover to arrow direction after one screw is unscrewed. 31

33 DOOR When the power cord is plugged,the door can be opened by pressing the DOOR OPEN button Open the door completely. Remove the two screws from the hinge. Door opening method in case of no electricity Pull the strap. STRAP Cap(Remaining Hose) Removing method of remained water Rotate the Cap(Remaining Hose) to arrow direction. Pull it out from hose. First, prepare a bucket to put in the remained water. 32

34 GASKET ASSEMBLY The cabinet gasket clamp is released. Two screws are unscrewed from the cabinet cover. Cap (Remaining Hose) One screw is unscrewed from the lower cover. The lower cover is disassembled by pulling out. Three screws are unscrewed from the cabinet. The control panel is removed. Screw is unscrewed from the cabinet cover. 33

35 Tub Gasket Clamp Remove tub gasket clamp by loosening the screw. Remove dry gasket clamp by loosening the screw. Dry Gasket Clamp When reassembling the gasket, put the drain hole of the gasket downward, then assemble. Drain Hole 34

36 PULLEY, MOTOR, DAMPER Rotor Remove the back cover. After loosening the bolt, Rotor, pull out the rotor. Bolt Remove the 6 bolt from the stator. Disconnect the 2 connectors. HOW TO ASSEMBLE THE MOTOR Bolt Hinge (Damper) Remove the bolts at the Tub. The Hinge (Damper) at the base is pulled off pressing on the snaps at the sharp end. The hinge at the base is pulled off. (To arrow direction) Friction Damper 35

37 Screw Cap (Remaining Hose) PUMP Pump Outlet Hose Tub Pump Bellows Remove pump outlet hose. Remove tub pump bellows. Remove cap (Remaining Hose). Disconnect the wiring. Three screws are unscrewed from the cabinet. Remove the pump to arrow direction. Washing Heater Ring Terminal Nut HEATER Loosen the nut. Remove washing heater by pulling out. When assembling the washing heater, insert the heater to heater clip on the bottom of tub. THERMISTOR Thermistor Bracket Pull it out by holding the thermistor bracket. If holding the wire and pulling out it, it may be broken. Thermistor bulb 36

38 DOOR HINGE ASSEMBLY Two screws are unscrewed on the door and the door is disassembled. The cabinet cover clamp is removed and the gasket is released. Two screws are unscrewed on the door hinge. The door hinge is disassembled by pushing the door hinge arm inside the cabinet cover. SWITCH ASSEMBLY, DOOR LOCK The cabinet cover clamp is removed and the gasket is released. Two screws are unscrewed. The door lock S/W is disconnected form the wiring connector and the strap. WHEN FOREIGN OBJECT STUCK BETWEEN DRUM AND TUB Hole Remove washing heater. Remove the foreign object(wire,coin,etc) by inserting long bar in the hole. Washing Heater 37

39 Dry Duct Upper DRY DUCT Dry fan Assembly Remove 5 screws and dry fan assembly. Remove 6 screws and dry duct upper. Thermostat Dry Heater Remove 1 screw and dry heater. Remove thermostat. CONDENSING DUCT Remove 2 screws from cabinet. Remove clamp and condensing duct. Condensing Duct Clamp Condensing Bellows 38

40 10. EXPLODED VIEW AND PART LIST 10-1.THE EXPLODED VIEW OF CABINET ASSEMBLY A154 A153 A110 A152 A151 A150 A102 A101 A104 A141 A103 A131 A100 A130 A140 A430 A440 A134 A450 A133 A410 A303 A310 A275 HOT (RED) A276 COLD (BLUE) A300 A200 A201 A220 39

41 10-2 THE EXPLODED VIEW OF CONTROL PANEL & DISPENSER ASSEMBLY F300 F462 F322 F321 F170 F160 F464 F310 F320 F226 F466 F432 F325 F225 F227 F436 F430 F220 F431 F441 F430 F435 F120 F110 F210 F130 40

42 10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBLY K140 K141 K110 K142 K411 K420 K115 K125 K121 K122 K360 K130 K131 K311 K123 K143 K350 K351 F140 K310 K511 K510 K111 K611 K610 K105 K410 K530 K320 K540 F467 K340 K346 K344 K342 F468 K K550

43 10-4 THE EXPLODED VIEW OF DRYER M111 M120 M110 M100 M121 M312 M310 M215 M210 M101 M220 M311 K311 M230 M260 44