HydroZone Installation Manual

Transcription

1 Hydronic omfort Zoning System 4, 8, and 12 Zone apacity Installation Information HydroZone Installation Manual Thermostat Installation Electrical Startup rocedures Wiring Schematics IM1550EW 11/10

2

3 HDZNE INSTALLATIN MANUAL Table of ontents Model Nomenclature eneral Installation Information... 5 Dimensional Data Electrical atings Electrical Wiring... 7 Wiring Schematics Thermostat Installation ontroller peration System Startup and heckout arts Lists... 21

4 HDZNE INSTALLATIN MANUAL Model Nomenclature 1-2 HZ A S 8 N Model Type HZ = HydroZone ontrol anel Number of Zones 04 = 4 Zone 08 = 8 Zone 12 = 12 Zone Vintage A = urrent Future N = None ontroller N = Standard with ontroller E = 12 Zone Expansion - No ontroller Zone utput Voltage A = 24 VA (Zone Valves) 9 = 115 VA (Zone umps) Zone Thermostat Zone Thermostat HydroZone ontroller utdoor Air Sensor Zone ump/valves Backup Heat - W H alls - 1 and 2 Load lumbing Accessory Box adiant Floor Tank Sensor Source lumbing eotank Envision Air Handler 4

5 HDZNE INSTALLATIN MANUAL eneral Installation Information Safety onsiderations Installing and servicing heating and air conditioning equipment can be hazardous due to system electrical components. nly trained and qualified service personnel should install, repair or service heating and air conditioning equipment. When working on equipment, observe precautions in the literature, tags and labels attached to the unit, and other safety precautions that may apply. Follow all safety codes. Wear safety glasses and work gloves. WANIN: Before performing service or maintenance operations on the system, turn off main power switches to the indoor unit. Turn off accessory heater power switch if applicable. Electrical shock could cause serious personal injury. HydroZone ontrol anel Locate the HydroZone panel in an indoor area that has enough space for service personnel to perform maintenance or repair. rovide sufficient room to make electrical connection(s). The HydroZone is not approved for outdoor installation and, therefore, must be installed inside the structure being conditioned. Do not locate the control panel in areas where ambient conditions are not maintained within 45 F to 95 F and are greater than 75% relative humidity. The HydroZone control panel should be mounted on or as close to the unit as possible by using the sheet metal screws provided. See the HydroZone ontrol anel Mounting illustration for mounting hole locations. Note: Use longer screws (not provided) to penetrate through drywall into stud. Delivery Information When the equipment is received, all items should be carefully checked against the bill of lading to be sure all crates and cartons have been received. Examine the contents for shipping damage, removing them from the cartons if necessary. If any damage is noted, the carrier should make the proper notation on the delivery receipt, acknowledging the damage. Installation and Design Steps 1. Decide which areas of a home or office will comprise each of the individual zones. A maximum of twelve individual zones can be chosen. If more zones are necessary, a 12 zone expansion is available. 2. alculate loads using software or other recognized methodology. 3. Use software to determine the equipment size and performance based on the total heating and cooling demands of the building, not the sum of the individual zone demands. 4. Find the peak heating and cooling demands and the peak M or FM required for each of the zones. 5. Lay out and size the radiant tubing or supply air ductwork. are should be taken to avoid under sizing either the buffer tank, radiant tubing and spacing, supply air systems, return air systems, or diffusers. 6. Decide where to locate the thermostats. 7. Install the unit, storage tank and the HydroZone system. 5

6 HDZNE INSTALLATIN MANUAL Dimensional Data HZ04, HZ08, and HZ12 Dimensions HZ00 Dimensions

7 HDZNE INSTALLATIN MANUAL Electrical atings 4 Zone 115V ump Model: Voltage: 115 hase: 1 Frequency: HZ04A9*N 60Hz Total FLA: 9.3 Maximum Fuse Size: omments: 15 - HA breaker or time delay fuse Maximum current per pump must not exceed 2.15 amps. 4 Zone 24V Valve (1 transformer included) Model: Voltage: 115 hase: 1 Frequency: HZ04AA*N 60Hz Total FLA: 0.65 Maximum Fuse Size: 3 omments: Maximum VA load per valve must not exceed 10 VA or 0.42 amps at 24VA. 8 Zone 115V ump Model: Voltage: 115 hase: 1 Frequency: HZ08A9*N 60Hz Total FLA: 17.9 Maximum Fuse Size: omments: 30 - HA breaker or time delay fuse Maximum current per pump must not exceed 2.15 amps. 8 Zone 24V Valve (2 transformers included) Model: Voltage: 115 hase: 1 Frequency: Total FLA: 1.3 Maximum Fuse Size: 6 omments: HZ08AA*N 60Hz B5 Maximum VA load per valve must not exceed 10 VA or 0.42 amps at 24VA. 12 Zone 115V ump Model: Voltage: 115 hase: 1 Frequency: HZ12A9*N 60Hz Total FLA: 26.5 Maximum Fuse Size: omments: 45 - HA breaker or time delay fuse Maximum current per pump must not exceed 2.15 amps. 12 Zone 24V Valve (2 transformers included) Model: Voltage: 115 hase: 1 Frequency: Total FLA: 1.3 Maximum Fuse Size: 6 omments: HZ12AA*N 60Hz Maximum VA load per valve must not exceed 10 VA or 0.42 amps at 24VA. Electrical Wiring B4 Wiring Zone Valves or umps All wiring must comply with local and state codes. Disconnect the power supply before beginning to wire to prevent electrical shock or equipment damage. All wiring should be run back to the control panel. Keep wires a minimum of 12 inches from any high voltage lines. See the Wiring Schematics section for additional information. Main ower Block Hydrozone ower 115/60/1 B1 WANIN: All wiring must comply with local and state codes. Disconnect the power supply before beginning to wire to prevent electrical shock or equipment damage. 7

8 HDZNE INSTALLATIN MANUAL Wiring Schematics 12 Zone 24VA Valves eotank Sensor AT Sensor Future B B3 Tank Tank AT AT lg om om om Brown (18) Brown (17) ellow (16) ellow (15) HZ A+ B+ ND AT TS ND HydroZone ontroller V /B ellow (1) ink () range (/B) Black () ed () reen (4) ray (3) Blue (2) Note 3 Zone Stats 1-4 Zone Stats 5-8 Zone Stats B5 Z1 Z2 Z3 Z4 reen/ellow (ND) B7 Z5 Z6 Z7 Z8 B9 Z9 Z10 Z11 Z12 Black/White (14) 4 2 elay Black/White Black/White (26) Black/White (34) ellow (13) ellow ellow (25) ellow (33) el (Z1) rn (Z3) Blk (1) Blue (Z2) ink (Z4) el (Z5 ) rn (Z7) Blk (2) Blue (Z6) ink (Z8) el (Z9) rn (Z11) Blk (3) Blue (Z10) ink (Z12 ) Black/White (12) ZB ZB ZB ellow (11) EA Seri es B E4 E3 E2 E1 N N N N EA Series B E4 E3 E2 E1 N N N N Black (6) Black (20) Black (28) Black Black Black Black Black Black EA Seri es B E4 E3 E2 E1 N N N N Black Black Black Note 1 Black (10 ) Black (9) Black (8) Black (7) Black (24) Black (23) Black (22) Black (21) Black (32) Black (31) Black (30) Black (29) White () White () White () White () White () White () White () White () White () White (5) White (19) White (27) ellow Transformer2 Black Black/White 24V 115V White B4 B6 B8 24V Transformer1 115V Black White Note 2 Note 2 Note 2 Zone Valves 1-4 Zone Valves 5-8 Zone Valves VA 24VA 24VA Hydrozone ower 115/60/1 B1 8

9 Zone Thermostat HDZNE INSTALLATIN MANUAL Wiring Schematics cont. 12 Zone 24VA Valves cont. B Note1 elay Board -2 elay 2 elay elay 1 elay elay 4 elay elay 3 elay Synergy3D option Synergy 3D Synergy 3D Synergy 3D Synergy 3D NSW/NDW ompressor 2 ompressor 1 ompressor 4 ompressor 3 B2 Tank ump Note 4 N 115 or 230/60/1 B8 Note 2 Note 1 elay Board 6-4 elay 42 elay ptional connection if auxiliary heat is used and heat pump 4 is not connected Notes 1. If an auxiliary water heater is used, connect to 6 on the relay board as shown above. 2. Wire zone valves or zone pumps to B4, B6, and B8 3. Wire zone thermostats to B5, B7, and B9 4. Use HZAB or field supplied contactor N Factory Low voltage wiring Factory Line voltage wiring Field low voltage wiring Field line voltage wiring ptional block D Voltage B traces Junction Quick connect terminal Wire nut Field wire lug round - elay ontacts N.., N.. Fuse HZ - Hydrozone ontrol B - elay Board B - ower Block Legend Water Heater 2 T 3 230/60/1 1 Thermistor Light emitting diode - reen elay coil olarized connector ZB - Zone elay Board HZAB - HydroZone Accessory Box Note /11/10 Thermostat Wiring Z1 B5, 7, & 9 9

10 HDZNE INSTALLATIN MANUAL Wiring Schematics cont. 12 Zone 115V umps B3 eotank Sensor AT AT AT Sensor Tank Tank Future lg om om om Brown (18) Brown (17) ellow (16) ellow (15) HZ A+ B+ ND AT TS ND HydroZone ontroller V /B ellow (1) ink () range (/B) Black () ed () reen (4) ray (3) Blue (2) B Note 3 Zone Stats 1-4 Zone Stats 5-8 Zone Stats B5 Z1 Z2 Z3 Z4 ellow (13) reen /ellow (ND) B7 Z5 Z6 Z7 Z8 Black/White (14) B9 Z9 Z10 Z11 Z12 4 ela Black/White ellow Black/White (26) ellow (25) Black/White (34) ellow (33) ZB1 el (Z1) rn (Z3) Blk (1) Blue (Z2) ink (Z4) ZB2 el (Z5) rn (Z7) Blk (2) Blue (Z6) ink (Z8) ZB3 el (Z9) rn (Z11) Blk (3) Blue ink (Z12) (Z10) Black/White (12) ellow (11) EA Series B E4 E3 E2 E1 N N N N EA Series B E4 E3 E2 E1 N N N N EA Series B E4 E3 E2 E1 N N N N Note 1 Transformer Black Black Black Black Black (10) Black (9) Black (8) Black (7) Black Black Black Black (24) Black (23) Black (22) Black (21) Black (6) Black (20) Black (28) White () White () White () White () White () White () B4 White (5) White (19) White (27) B6 Black Black Black B8 Black (32) Black (31) Black (30) Black (29) White () White () White () 115V 24V White Note 2 Note 2 Note 2 Zone umps 1-4 Zone umps 5-8 Zone umps /60/1 115/60/1 115/60/1 Hydrozone ower 115/60/1 B1 10

11 Zone Thermostat HDZNE INSTALLATIN MANUAL Wiring Schematics cont. 12 Zone 115V umps cont. To Heat umps NSW/NDW Synergy3D option ompressor 2 B -2 elay 2 Synergy3D elay ompressor 1 1 elay 1 elay Synergy3D ompressor Note1 elay Board -4 elay 4 elay elay 3 elay Synergy 3D Synergy3D ompressor 3 Note 4 Tank ump Note 1 elay Board B2-4 elay 42 N N 115 or 230/60/1 Water Heater 230/60/1 Note 4 elay Legend Note 2 ptional connection if auxiliary heat is used and heat pump4 is not connected Notes 1. If an auxiliary water heater is used, connect to 6 on the relay board as shown above. 2. Wire zone valves or zone pumps to B4, B6, and B8 3. Wire zone thermostats to B5, B7, and B9 4. Use HZAB or field supplied contactor Factory Low voltage wiring Factory Line voltage wiring Field low voltage wiring Field line voltage wiring ptional block D Voltage B traces Junction Quick connect terminal Wire nut Field wire lug round - elay ontacts N.., N.. Fuse HZ - Hydrozone ontrol B - elay Board 2 B - ower Block ZB - Zone elay Board T 3 Thermistor Light emitting diode - reen elay coil 1 olarized connector /22/10 Thermostat Wiring Z1 B5, 7, & 9 11

12 Zone Thermostat HDZNE INSTALLATIN MANUAL Wiring Schematics cont. 12 Zone 24VA Valves Note 2 Zone Stats 1-4 Zone Stats 5-8 Zone Stats 9-12 B5 Z1 Z2 Z3 Z4 B7 Z5 Z6 Z7 Z8 B9 Z9 Z10 Z11 Z12 reen /ellow (ND) Black/White ellow Black/White (26) ellow (25) Black/White (34) ellow (33) ZB1 el (Z1) rn (Z3) Blk (1) Blue (Z2) ink (Z4) ZB2 el (Z5) rn (Z7) Blk (2) Blue (Z6) ink (Z8) ZB3 el (Z9) rn (Z11) Blk (3) Blue (Z10) ink (Z12) Black/White (12) ellow (11) B2 EA Series B E4 E3 E2 E1 N N N N EA Series B E4 E3 E2 E1 N N N N EA Series B E4 E3 E2 E1 N N N N Black (6) Black (20) Black (28) Black Black Black Black (10) Black (9) Black (8) Black (7) Black Black Black Black (24) Black (23) Black (22) Black (21) Black Black Black Black (32) Black (31) Black (30) Black (29) White (5) White () White () White () White () White () White () White () White () White () B4 B6 B8 White (19) White (27) Note 1 Note 1 Note 1 ellow Black/White 24V ellow Black/White Transformer1 115V 24V Transformer2 Hydrozone ower 115/60/1 Black White 115V B1 Zone Valves 1-4 Zone Valves 5-8 Zone Valves 9-12 Black White 24VA 24VA 24VA Notes 1. Wire 24VA zone valves to B4, B6, and B8. 2. Wire zone thermostats to B5, B7, and B9. Legend Factory Low voltage wiring T Factory Line voltage wiring Field low voltage wiring Field line voltage wiring ptional block D Voltage B traces 2 3 Junction Quick connect terminal Wire nut Field wire lug round - elay ontacts N.., N.. Fuse HZ - Hydrozone ontrol B - elay Board B - ower Block ZB - Zone elay Board 1 Thermistor Light emitting diode - reen elay coil olarized connector /22/10 Thermostat Wiring Z1 B5, 7, & 9 12

13 HDZNE INSTALLATIN MANUAL Thermostat Installation Locating the Thermostats The thermostats must be located in the room or zone that each controls. Locate a thermostat about five feet above the floor. Do not locate a thermostat where it may be exposed to direct sunlight, drafts or direct supply air. Do not place a thermostat on an outside wall. Follow the same guidelines that apply with standard thermostat installation. If two or more rooms are on a single zone, locate the thermostat in a hallway or area where it can sense the return air from all rooms. Four Zone Thermostat Location Utility oom Dining Kitchen Bath Bath Master Bedroom Family oom Living oom Bedroom Bedroom Zone 1 Main Living Zone 2 Bedrooms Not Shown Zone 3 Master Suite Zone 4 Basement HydroZone Thermostat Mounting and Wiring the Thermostat osition the thermostat subbase against the wall so that it is level and the thermostat wires protrude through the middle of the subbase. Mark the position of the subbase mounting holes and drill holes with a 3/16-inch bit. Install supplied anchors and secure base to the wall. Thermostat wire must be eight-conductor 18 AW. Strip the wires back 1/4 inch (longer strip lengths may cause shorts) and insert the thermostat wires into the HydroZone connector as shown to right. Tighten the screws to ensure tight connections. The thermostat has the same type connectors, requiring the same wiring. aulk the hole in the wall where the wires enter the thermostat. Note: See the instructions enclosed in the thermostat for detailed installation and operation information. 13

14 HDZNE INSTALLATIN MANUAL ontroller peration The WaterFurnace HydroZone controller is a part of the hydronic heat pump system. The WaterFurnace part number for this product is HZ. This controller is a human interface and water tank control device. The controller displays and regulates the water tank temperature as configured. A 2-1/2 in. x 2-1/2 in. LD display and five push button keys serve as the human interface. The five keys are: the up and down keys ( and ) for changing the selection or temperature, the right and left keys ( and ) for changing the selection or mode, and the enter key ( ) is for accepting and/or saving the selection. ontroller peration Adjusting Temperature 1. To select a MDE, use the keypad arrows to scroll to MDE. Then, press the enter button on the key pad to enter the operating mode menu. 2. Select the desired mode by scrolling up or down, with the arrows. Then press the enter button on the keypad to enter into that mode. 3. ou are now returned to the Main Menu and Figure 1 is a similar view. NTE: utdoor air temperature is only displayed if an outdoor air sensor is installed. 4. To increase the temperature set point, use the arrow up button. To decrease the set point, use the arrow down button. Five (5) seconds after the last button push, the new setpoint is saved. utdoor reset control is done in the installer s setup and cannot be adjusted from the front screen. Setting Date And Time 1. From the Main Menu, scroll to MENU and press the enter button on the keypad. 2. Select SET DATE. 3. SET MNTH by using the up and down arrows. Then press the enter button on the keypad to save the month. 4. SET DA by using the up and down arrows. Then press the enter button on the keypad to save the day. 5. SET EA by using the up and down arrows. Then press the enter button on the keypad to save the year. 6. Select SET TIME. 7. SET HU by using the up and down arrows. Then press the enter button on the keypad to save the hour. 8. SET MINUTE by using the up and down arrows. Then press the enter button on the keypad to save the minute. 9. If your area observes daylight savings time, select AUT DALIHT SAVIN; scroll to N, then press the enter button to save. ou will be returned to the SET DATE AND TIME menu. Scroll to SET DATE AND TIME and press the enter button on the keypad. Figure The date and time are now set. ou can return to the Main Menu by pressing the left arrow key to return to the previous menu. hanging Modes 1. From the main screen select MDE. 2. Select the operating mode you need and press the enter button. NTE: If selecting EMEEN HEAT, the backlight color will change from blue to red indicating that auxiliary heat is operating instead of the heat pump compressor. Auxiliary/emergency heat is significantly more expensive to operate than the heat pump compressor, and should not be selected unless the heat pump compressor is not operational. Fahrenheit or elsius 1. From the Main Menu, scroll to MENU and press the enter button on the keypad. 2. Select FAHENHEIT/ELSIUS. 3. Select which scale you prefer. Backlight on Time This controller has a two color backlight feature. Anytime a button is pressed, the blue backlight stays on for a certain amount of time. A red backlight is visible if you are selecting Emergency Heat mode. ou can adjust the amount of time the backlight stays on in the menu options. 1. From the Main Menu, scroll to MENU and press the center button on the keypad. 2. ou can change the backlight on time by using the up and down arrows. BAKLIHTIN N (all the time), 15 sec., 30 sec., and N BAKLIHTIN are your choices. ress the enter button to save the new backlight on time. 14

15 HDZNE INSTALLATIN MANUAL ontroller peration cont. Advanced Settings Security Lockout This controller has the option to set security features to lockout everything but the adjustment of the temperature or a total keypad lockout. 1. From the Main Menu, scroll to MENU and press the enter button on the keypad. 2. Select LK/UNLK. 3. The selection will bring you to the Enter in Number screen. 4. Using the up and down arrows, select a pin number to lock out the thermostat. The right arrow moves you to the next pin digit. 5. nce you ve entered the 4-digit pin number, press the enter button to save the pin. The screen will display LKED and return to the main Screen. 6. nce you return to the Main Screen, in the upper left of the screen will alternate between LKED and the date and time. 7. nce unlocked, you will have to reset a pin number again to lockout the thermostat again. 8. In the event the pin number is lost, the default is Installer Information and Advanced Features Safety onsiderations Improper wiring or installation may damage the controller. Wiring must conform to local and national electrical codes. Introduction The controller is a low-voltage controller which maintains geo storage tank temperature by controlling the operation of multiple hydronic heat pumps system. Batteries are not required; temperature and mode settings are preserved with the power off. The controller is not a power stealing device and MUST have both and connected. HydroZone Installation 1. Turn off all power to unit. 2. Separate the front and back pieces of the HZ0. 3. Mount the base of the HZ0. 4. onnect wires to proper terminal on the pump relay. (see wiring schematic on page 4). 5. eplace the cover on the base. 6. Turn on power to the unit. Main Screen After exiting from the setup mode, controller displays the main screen. EATIN, displays the current controller setup selection. They are UTD, T AUT, and T MANUAL MDE. If the operation mode is outdoor reset or tank control auto, the MDE should display FF, N, or EHEAT. If the operation mode is tank control manual, the MDE should display FF, HEAT, L, or EMHT. UTUT shall display the current status of the outputs (WAM WEATHE SHUTDWN, STANDB, 1, 2, 3, 4, or AUX). STANDB mode is active when the controller is satisfied and waiting for a call. 1, 2, 3, and 4 will be off and will stay in its previous state. If the outputs are off due to a warm weather shutdown condition, the proper message should be displayed. Tank setpoint temperature utdoor air temperature urrent mode of operation urrent tank temperature urrent compressor outputs FF, N, EMEEN SET DATE, SET TIME, BAKLIHTIN, F/, LK/ UNLK, SEVIE NTAT INF 15

16 HDZNE INSTALLATIN MANUAL ontroller peration cont. Mode Select Display and Thermostat ontrols Manual Tank Display EATIN MDE SELETIN utdoor eset or Tank Auto ontrol EATIN MDE SELETIN FF HEATIN NL LIN NL EMEEN HEAT FF N EMEEN HEAT SELETIN EVIUS ENTE SELETIN EVIUS ENTE Maximum water temperature needed for minimum AT hange setpoint, temperature, or mode selection Lowest design water temperature Enter or save selection Lowest design outside air temperature hange selection or mode Highest design outside air temperature hange setpoint temperature or mode selection 16

17 HDZNE INSTALLATIN MANUAL ontroller peration cont. Wiring Schematic eotank Sensor AT Sensor B -2 elay 2 To Heat umps Synergy3D option Synergy 3D 5-4 NSW/NDW ompressor 2 B3 Future Future Tank Tank AT AT Brown (ND) Brown (AT) ellow (TS) ellow (ND) HZ A+ B+ ND AT TS ND HydroZone ontroller V /B reen (4) ray (3) Blue (2) ellow (1) ink () range (/B) Black () ed () elay elay 1 elay Synergy 3D ompressor 1 ompressor 4 elay 4 ellow (1) Black/White (2) Note1 elay elay 3 elay 3-3 Synergy 3D ompressor 3 elay Board -4 elay 42 elay 41 elay Board ellow (3) 6-3 Synergy 3D ptional connection if auxiliary heat is used and heat pump 4 is not connected Notes 1. If an auxiliary water heater is used, connect to 6 on the relay board as shown above. N N HydroZone Accessory ontrol Box Tank ump 115 or 230/60/1 HydroZone Accessory ontrol Box Water Heater 230/60/1 Legend Factory Low voltage wiring T Thermistor Factory Line voltage wiring Field low voltage wiring Light emitting diode - reen Field line voltage wiring ptional block elay coil D Voltage B traces Junction Quick connect terminal olarized connector Wire nut HZ - Hydrozone ontrol Field wire lug B - elay Board B - ower Block round ZB - Zone elay Board elay ontacts- N.., N.. Fuse /14/09 Installer Settings These options are intended to be used by the installer. End users are not advised to change or modify any of these settings. Doing so may make your equipment stop working properly and/or may void the warranty of the controller as well as the equipment hooked up to the controller. To access the installer setting menu, the mode must be set to FF. Then, press both the up and down arrow keys at the same time for at least 5 seconds to enter the installer screen. After initial power-up, you re-enter installer setup. If no selection is made within 30 seconds, the controller will return to the main screen. ontroller Setup ptions to select from: 1. utdoor eset - This control mode uses the outdoor reset algorithm to continuously adjust the set point. The set up menu allows selection of Maximum Tank Temperature at a corresponding outdoor air 17

18 HDZNE INSTALLATIN MANUAL ontroller peration cont. temperature (AT), and Minimum Tank Temperature at its corresponding AT. An outdoor air sensor must be installed. Set point A is the maximum tank temperature set point: Tank temperature (TANK_A) range is 100 F to 130 F, and default as 120 F. utdoor air temperature (AT) range is 0 F to 20 F, and default as 0 F. Set point B is the minimum tank temperature set point: Tank temperature (TANK_B) range is 70 F to 90 F, and default as 80 F. utdoor air temperature (AT) range is 40 F to 60ºF, and default as 60 F. be changed from the main screen by pushing the U or DWN buttons. Selecting ENTE shall take the screen to the NTLLE SETU screen. This option will maintain the temperature with a tighter deadband and automatically switch the heat pump between heating and cooling to maintain the setpoint. The factory default is 120 F heating and 5 F dead band. All these temperature setting are with increments of 1 F. The dead band is 2 F to 15 F with Increments of 1 F. Tank Temperature Set point is calculated internally by the outdoor reset algorithm, and updated every 30 minutes if this setup is selected. Warm Weather Shutdown: If the warm weather shutdown is selected, the controller will check the outdoor air temperature sensor every 30 minutes. If the temperature is higher than the set temperature selected for 50 continuous hours, then the HydroZone ontroller will enter the warm weather shutdown mode. If the temperature drops below the selected setpoint for 5 continuous hours, the controller will exit the warm weather shutdown mode and return back to normal. Warm weather shutdown selections are None, 45, 50, 55, 60, and 65. The factory default is None. 3. Tank ontrol Manual - There shall be no automatic changeover from heating to cooling or vice versa. Heating and cooling modes must be selected manually. If heating fixed is selected, the default temperature for tank setpoint is 120 F with a 10 F deadband. The set range is 80 F to 130 F, with Increments of 1 F. The dead band is 2 F to 15 F with Increments of 1 F. The factory defaults are 120 F heating and 5 F dead band, 80 F cooling and 5 F dead band, and warm weather shutdown is None. When the selection is moved to WAM WEATHE SHUTDWN, ENTE shall take the screen to the WAM WEATHE SHUTDWN screen. When ENTE is selected, the installer shall be taken to the LIN screen. 2. Tank ontrol Auto - Default temperature for tank setpoint is 120 F with a 5 F deadband. The set range is 40 F to 130 F, with Increments of 1 F. The dead band is 2 F to 5 F with Increments of 1 F. The setpoint can 18

19 HDZNE INSTALLATIN MANUAL ontroller peration cont. If no heating is selected, the screen shall go to the LIN screen. If cooling fixed is selected, the default temperature for tank setpoint is 80 F with a 10 F deadband. The set range is 40 F to 85 F, with Increments of 1 F. The dead band is 2 F to 15 F with Increments of 1 F. utput Setup onfiguration ptions Factory Defaults 1 Single Dual1 Stage1 Single 2 Single Dual1 Stage2 ff ff 3 Single Dual2 Stage1 ff ff 4/W Single Dual2 Stage2 Aux ff ff If AUX is selected in stage 4, ENTE would take the user to ADDITINAL DEAD BAND F AUX HEAT screen and then to MAXIMUM AT F AUX HEAT screen. The ADDITINAL DEAD BAND F AUX HEAT would enable the installer to select how much extra dead band should be added on top of the heat dead band before auxiliary heat would come on. The range is between 5 and 15 F. Staging The controller can control up to four stages of compressors or three compressors and one auxiliary heat. How the unit stages the outputs will be determined by how the outputs are configured. When selecting a dual capacity unit, the next available stage will automatically become dual stage 2. Example: If DUAL 1 ST 1 has been selected for 1 then 2 will automatically be DUAL 1 ST 2. Staging Screen STAIN Staging Setup of 1 Dual ompressor and 1 Single with Aux Enabled STAIN In the MAXIMUM AT F AUX HEAT the installer can select between NNE or a certain outdoor air temperature. If the installer selects a certain temperature for AT, the AUX heat shall not come on if the outdoor air temperature is above that temperature. The range is between 0 F and 40 F. If NNE is selected, the AUX heat can come on at any time regardless of the outdoor air temperature. An outdoor air sensor must be installed for this option. 1 SINLE / DUA ST1 2 FF / SINLE / DUA ST2 3 FF / SINLE / DUA ST1 4 FF / SINLE / DUA ST2 / AUX WANT T HANE? ES N TIN ENTE DUA ST1 DUA ST2 SINLE AUX ADDITINAL DEAD BAND F AUX 5 MAXIMUM AT F AUX HEAT 40 WANT T HANE? ES N TIN ENTE 19

20 HDZNE INSTALLATIN MANUAL ontroller peration cont. Lead/Lag If only 1 is selected in the staging, the lead/lag will be selected as N, and can not be changed. Each compressor output will have an accumulator to keep track of total run time. If any accumulator ran up to the maximum count, all the accumulators shall be reset. Total run time will be reset when lead/lag N is selected. The default setting is N. When the installer selects ENTE from any of the BAND NAME, MDEL NUMBE, SEIAL NUMBE, NTAT NAME, and NTAT HNE screens, the main INUT DEALE INF screen is shown. In order to save the dealer information in the permanent memory, the installer shall select SAVE from the main INUT DEALE INF screen and hit ENTE. The following screen is shown summarizing the information the installer has inserted in the previous screens. First n ompressor stage with least amount of accumulated run time. First ff ompressor stage with most amount of accumulated run time. Factory Defaults When ES is selected for ESTE FAT DEFAULTS, the controller will restore the factory defaults configuration. Factory default control option is tank control manual. The factory defaults are 120 F heating, 5 F dead band, and warm weather shutdown None. Service ontact Information Input dealer info. INUT DEALE INF BAND NAME MDEL NUMBE SEIAL NUMBE NTAT NAME NTAT HNE DEALE INF BAND NAME: USE T SLL THU HAATES WATE FUNAE SAVE SELET TIN EVIUS ENTE HANE LETTE EVIUS ENTE 20

21 HDZNE INSTALLATIN MANUAL System Startup and heckout System heckout The HydroZone controller needs to be set to manual heating and cooling for the following start-up procedures. Set all of the zone thermostats to the cooling mode. educe the cooling set point to 1 above the actual zone temperature on all thermostats. First stage cooling should energize after a delay. utput LEDs on ZB1-3 should be on. Verify zone valve is operating or pump is running Set all zone thermostats to heating mode Increase heating set point to 1 above the actual zone temperature on all thermostats. First stage heating should energize after a delay. utput LEDs on ZB1-3 should be on. Verify zone valve is operating or pump is running. Instruct the owner/operator of correct thermostat and system operation. Fill out and forward all warranty registration papers to WaterFurnace. arts Lists art Number HZ HZ0 HZ04AANN HZ04A9NN HZ08AANN HZ08A9NN HZ12AANN HZ12A9NN HZ12AAEN HZ12A9EN HZAB Specification HydroZone ontrol nly HydroZone ontrol with signal isolation board - 0 Zone (24V only) HydroZone ontrol with signal isolation board - 4 Zone 24V output (valve) HydroZone ontrol with signal isolation board - 4 Zone 115V output (pump) HydroZone ontrol with signal isolation board - 8 Zone 24V output (valve) HydroZone ontrol with signal isolation board - 8 Zone 115V output (pump) HydroZone ontrol with signal isolation board - 12 Zone 24V output (valve) HydroZone ontrol with signal isolation board - 12 Zone 115V output (pump) 12 Zone expansion and not equipped with the HydroZone ontrol or relay board - 24V output (valve) 12 Zone expansion and not equipped with the HydroZone ontrol or relay board - 115V output (pump) HydroZone Accessory Box (water heater or pump control) L /4" SWT Zone valve motorized sweat (Qty 1) L " SWT Zone valve motorized sweat (Qty 1) TSU02* utdoor Air Sensor (required with utdoor eset ontrol ) NTES: HZ0 is for tank control only with no zones. HydroZone ontroller arts List art Number Quantity Description Mass Label Sheet osition Terminal Block ontrol Box ontrol Box over Wire Kit 91001A18 6 Screw #6-32 X 5/ HydroZone ontroller Low Voltage elay Board 91001A43 4 Screw #10-24 X 3/ A12 1 Nut #

22 HDZNE INSTALLATIN MANUAL Notes 22

23

24 Manufactured by WaterFurnace International, Inc onservation Way Fort Wayne, IN IM1550EW 11/10 roduct: Type: Size: Document: HydroZone Hydronic omfort Zoning System 4, 8, and 12 Zone apacity Installation Manual 2010 WaterFurnace International, Inc., 9000 onservation Way, Fort Wayne, IN WaterFurnace has a policy of continual product research and development and reserves the right to change design and specifications without notice.