Brief Overview of 2013 Nonresidential Changes to Energy Standards: Mechanical Systems

Transcription

1 2013 Title 24, Part 6 Energy Standards Brief Overview of 2013 Nonresidential Changes to Energy Standards: Mechanical Systems Gina Rodda Gabel Associates, LLC CEA, CEPE, LEED AP / Principal gina@gabelenergy.com ext. 204 This program is funded by California utility customers under the auspices of the California Public Utilities Commission and in support of the California Energy Commission.

2 We Are. California Statewide Codes & Standards. This program is funded by California utility customers under the auspices of the California Public Utilities Commission and in support of the California Energy Commission. Here to help you meet the requirements of Title 24, Part 6 We offer FREE: Trainings Tools Resources All designed to improve compliance with the state s building energy code and aimed at locking in long-term energy savings. 2

3 When? When (current schedule): Any projects that apply for permit on or after JULY 1, 2014 will be subject to the 2013 Standards. Nonresidential Registry July 1, 2015 Appliance efficiency update January 1,

4 Where Can You Find? Where can you find? CEC website 4

5 Why? California s Goal (AB 32): Net Zero goals: Residential: 2020 Nonresidential: 2030 Rosenfeld Effect 5

6 CEC Documents 6

7 CEC Blueprint 7

8 Application of Standards (Table A) Number system has changed by adding decimal: was 101 New sections 110.1: Solar Ready buildings 120.6: NR: Covered Processes instead of Refrigerated Warehouses 120.7: NR Mandatory Insulation Requirements 120.8: NR Building Commissioning 120.9: NR Mandatory Requirements for Commercial Boilers 130.5: NR Electrical Power Distribution Systems 140.9: NR Prescriptive Requirements For Covered Processes 141.1: NR Requirements For Covered Processes In Additions, Alterations To Existing Buildings That Will Be Nonresidential, High-Rise Residential, And Hotel/Motel Occupancies 8

9 Forms

10 Title 24 Part 6 Forms (2013) NRCC-MCH Non Residential Certificate of Compliance Submitted and included in plans set for building permit Includes Field Inspector Checkboxes NRCI-MCH Non Residential Certificate of Installation Filled out and signed by installing contractor Reviewed by Field Inspector NRCA-MCH Non Residential Certificate of Acceptance Filled out and signed by Certified Test Field Technician NRCV-MCH Non Residential Certificate of Verification Filled out and signed by HERS rater 10

11 Nonresidential Forms: Certificate of Compliance Form Name Use Description Design Review (NEW) NRCC-CXR-01-E Design Review Design Review Kickoff (completed at schematic design) NRCC-CXR-02-E Design Review Construction documents - general NRCC-CXR-03-E Design Review Construction documents simple HVAC systems NRCC-CXR-04-E Design Review Construction documents complex HVAC systems NRCC-CXR-05-E Design Review Design review signature page (completed at design stage) Performance Approach NRCC-PRF-01 New Construction, addition, alterations, E+A, E+A+A Performance documentation Form Name Use Description Electrical (NEW) NRCC-ELC-01-E Electrical Disaggregation of electric circuits Mechanical NRCC-MCH-01-E Mechanical Declarations and Field inspection list NRCC-MCH-02-E Mechanical Requirements Dry and wet systems NRCC-MCH-03-E Mechanical Mechanical ventilation and reheat NRCC-MCH-04-E Mechanical Declarations single zone systems NRCC-MCH-05-E Mechanical Requirements single zone systems Worksheets mechanical (NEW) NRCC-MCH-06-E Mechanical Max. cycles of concentration worksheet for cooling towers Plumbing (NEW) NRCC-PLB-01-E Plumbing Water heating systems Solar (NEW) NRCC-STH-01-E Solar thermal heating OG-100 worksheet NRCC-SRA-01-E Solar ready area Solar radiation availability Worksheets solar ready (NEW) NRCC-SRA-02-E Solar ready area Minimum solar zone area worksheet 11

12 Nonresidential Forms: Certificate of Compliance Form Name Use Description Process (many are NEW) NRCC-PRC-01-E Process Covered process NRCC-PRC-02-E Process Garage exhaust NRCC-PRC-03-E Process Commercial kitchens NRCC-PRC-04-E Process Data Centers NRCC-PRC-05-E Process Refrigeration Performance or prescriptive NRCC-PRC-06-E Process Refrigerated warehouses NRCC-PRC-07-E Process Refrigerated warehouse 3,000 sf or greater NRCC-PRC-08-E Process Refrigerated warehouse 3,000 sf or greater and served by same refrigeration system NRCC-PRC-09-E Process Laboratory exhaust NRCC-PRC-10-E Process Compressed air systems NRCC-PRC-11-E Process Process boilers -E: Enforcement (building department) -F: Field technician (installing contractor) -A: Acceptance test technician (or installing contracting until adopted by CEC) -H: HERS rater 12

13 Nonresidential Forms: Certificate of Installation Form Name Use Description Electrical (NEW) NRCI-ELC-01-E Electrical Power distribution Mechanical NRCI-MCH-01-E Mechanical Validation Plumbing NRCI-PLB-01-E Plumbing Water heating systems validation NRCI-PLB-02-E Plumbing Single dwelling unit hot water systems distribution NRCI-PLB-03-E Plumbing non HERS Multifamily central hot water systems distribution NRCI-PLB-21-H (HERS) Plumbing HERS Water heating systems distribution verified by HERS Process NRCI-PRC-01-E Process Refrigerated warehouse Solar NRCI-SPV-01-E Solar photovoltaic Validation NRCI-STH-01-E Solar Thermal heating Validation 13

14 Nonresidential Forms: Certificate of Acceptance Form Name Use Description Mechanical NRCA-MCH-02-A (ACCEPT) Mechanical Outdoor air NRCA-MCH-03-A (ACCEPT) Mechanical Constant volume singe zone HVAC NRCA-MCH-04-H (HERS) Mechanical Air distribution duct leakage verified by HERS NRCA-MCH-05-A (ACCEPT) Mechanical Air economizer controls NRCA-MCH-06-A (ACCEPT) Mechanical Demand control ventilation controls NRCA-MCH-07-A (ACCEPT) Mechanical Supply fan variable flow controls NRCA-MCH-08-A (ACCEPT) Mechanical Valve leakage test NRCA-MCH-09-F Mechanical Supply water temperature reset controls NRCA-MCH-10-A (ACCEPT) Mechanical Hydronic system variable flow controls NRCA-MCH-11-A (ACCEPT) Mechanical Automatic demand shed controls NRCA-MCH-12-F Mechanical Fault detection & Diagnostic for DX units NRCA-MCH-13-F Mechanical Fault detection & Diagnostics for air handling and zone terminal units NRCA-MCH-14-F Mechanical Distributed energy storage DX AC systems test NRCA-MCH-15-F Mechanical Thermal energy storage systems NRCA-MCH-16-F Mechanical Supply air temperature reset controls NRCA-MCH-17-F Mechanical Condenser water temperature reset controls NRCA-MCH-18-F Mechanical Energy management control system 14

15 Nonresidential Forms: Certificate of Acceptance Form Name Use Description Process NRCA-PRC-01-F Process Compressed air NRCA-PRC-02-F Process Commercial kitchen exhaust NRCA-PRC-03-F Process Parking garage exhaust NRCA-PRC-04-F Process Refrigerated warehouse Evaporator fan motor controls NRCA-PRC-05-F Process Refrigerated warehouse Evaporative condenser controls NRCA-PRC-06-F Process Refrigerated warehouse Air cooled condenser controls NRCA-PRC-07-F Process Refrigerated warehouse variable speed compressor NRCA-PRC-08-F Process Refrigerated warehouse electric resistance underslab heating **New qualifications required Acceptance Test Lighting Technician (to take effect when CEC believes there are enough people trained per their requirements) Acceptance Test Mechanical Technician (to take effect when CEC believes there are enough people trained per their requirements) HERS Verification NRCI-LTI-05: Power Adjustment Factors NRCI-PLB-21: Water heating distribution NRCA-MCH-05: Duct leakage testing NRCV-MCH: Duct leakage NRCV-PLB: Domestic hot water distribution 15

16 Acceptance Test Technician Certification Providers (ATTCP) Current ATTCP grandfathered in for 6 months Air-cooled The Energy Commission will determine whether in their entirety reasonable access to certification is provided by considering factors such as certification costs commensurate with the complexity of the training being provided, certification marketing materials, prequalification criteria, class availability, and curriculum. 16

17 Certified Acceptance Test Technicians (CATT) NA7.5.1 Outdoor Air Ventilation Systems NA7.5.2 Constant Volume, Single Zone Unitary Air Conditioners and Heat Pumps NA7.5.4 Air Economizer Controls NA7.5.5 Demand Control Ventilation Systems NA Supply Fan Variable Flow Controls NA7.5.7, NA7.5.9 Hydronic System Variable Flow Controls NA Automatic Demand Shed Controls Industry Coverage by Certification Provider(s). The Certification Provider(s) approved by the Energy Commission, in their entirety, shall provide reasonable access to certification for technicians representing the majority of the following industry groups: Professional engineers, HVAC installers, mechanical contractors, TAB certified technicians, controls installation and startup contractors and certified commissioning professionals who have verifiable training, experience and expertise in HVAC systems. Number of Certified Acceptance Test Technicians. There shall be no less than 300 Acceptance Test Technicians certified to perform the acceptance tests in Building Energy Efficiency Standards, Section The number of certified Acceptance Test Technicians shall be demonstrated by Certification Providerprepared reports submitted to the Energy Commission.

18 Nonresidential Forms: Certificate of Verification (HERS) Form Name Use Description Mechanical (NEW) NRCV-MCH-04a-H (HERS) Mechanical Duct leakage testing new system NRCV-MCH-04c-H (HERS) Mechanical Duct leakage testing Low leakage air handling units NRCV-MCH-04d-H (HERS) Mechanical Duct leakage testing Altered systems NRCV-MCH-04e-H (HERS) Mechanical Duct leakage testing Sealing of all accessible leaks Plumbing (NEW) NRCV-PLB-21-H (HERS) Plumbing Verification of domestic hot water distribution (HR multi family central system) NRCV-PLB-22-H (HERS) Plumbing Verification of domestic hot water distribution (HR single dwelling unit) Three HERS Providers in California: CalCerts CHEERS USERA 18

19 NRCC-CXR-01-E: Commissioning Owner s project requirements (OPR) Basis of design (BOD) Design Phase Design Review Schematic design: Design Review Kickoff Certificate (DESC-1C) on submitted plans Construction Documents Design Review Checklist Certificate form(s) (DESC-2C through DESC-5C) checked during construction, and included in Compliance documentation (register after 1/1/2015 to data registry) Moved from Calgreen Title 24 Part 11 to Part 6 Commissioning measures shown on construction documents Commissioning plan Functional performance testing Documentation and training 19

20 NRCC-CXR-02-E: All HVAC Systems 20

21 NRCC-CXR-03-E: Simple HVAC Systems 21

22 NRCC-CXR-04-E: Complex Mechanical Systems 22

23 NRCC-CXR-05-E: Design Review 23

24 Solar Ready

25 Nonresidential: Solar Ready 15% of total roof area excluding skylights, EXCEPT: Covered occupancy: Hotel/motel and high rise residential: 11 stories or more All other nonresidential: 4 or more stories Roof used for vehicular traffic parking, heliport PV system = 1 watt per sq. ft. of roof area Solar hot water system with solar savings fraction: 20% = CZ1 through 9 35% = CZ % potential solar zone area provided High Rise Residential: Demand response thermostats High efficacy lights at kitchen, bathrooms (with vacancy sensor), utility rooms, garages and outside (with occupancy and photo sensor) Every room has a switched receptacle 25

26 Mandatory Measures Mandatory Measures Two Ways to Comply with the Standards Prescriptive Approach ENV some tradeoff MECH no tradeoff No tradeoffs between ENV, MECH, and LTG LTG some tradeoff Performance Approach Standard Design Proposed Design Tradeoffs ENV MECH LTG * * See notes for restrictions

27 Simple Versus Complex HVAC System Complex Vs. Simple Mechanical Systems Complex Mechanical Systems are systems that include: 1) fan systems each serving multiple thermostatically controlled zones, or 2) built-up air handler systems (non-unitary or nonpackaged HVAC equipment), or 3) hydronic or steam heating systems, or 4) hydronic cooling systems. Complex systems are NOT the following: unitary or packaged equipment listed in Tables A (unitary AC), B (heat pumps), C (gas-engine heat pumps), and E (PTAC), that each serve one zone, or two-pipe, heating only systems serving one or more zones. 27

28 NRCC-MCH-02-E: Dry Systems Title 20 efficiencies to be updated 1/1/2015. Many added and updated equipment types. HVAC system with DDC to the zone level, must have thermostat must comply with JA5 (automatic demand shed controls) If using in performance calculations, must meet HERS verification requirements. Required in: Multipurpose rooms less than 1,000 sf, classrooms greater than 750 sf, conference, convention, auditorium and meeting centers greater than 750 sf. Air cooled unitary DX units with economizers and cooling capacity 54,000 BTUH or higher, must include fault detection and diagnostic system. VAV systems: dynamic controls to maintain outside air rates within 10% of required rate at full and reduced supply airflow conditions. Constant volume: measured outside air rates within 10% of required outside air. Features added: Facility operators can disable, and manually control adjustment of set points globally from singe point in EMCS, and upon receipt of a demand response signal conduct a centralized demand shed. 28

29 What s New: Dry System HVAC Measures Measure T 24 Section New Changed Heating Equipment Efficiency Cooling Equipment Efficiency or 110.2(a) or 110.2(a) No 5/1/2013 1/1/2015 1/1/2015 1/1/2015 No 1/1/2015 1/1/2015 No Notes Mandatory Measures Gas Furnace (not including mobile home or oil): Non weatherized (residential): 80% AFUE or higher; Weatherized: 81% AFUE or higher Split heat pump: 8.2 HSPF or higher Packaged heat pump : 8.0 HSPF or higher All others: See Table(s) Split: <45,000 Btuh = 14 SEER or higher/12.2 EER or higher; 45,000 Btuh = 14 SEER/11.7 EER or higher Packaged: 14 SEER / 11.0 EER All others: See Table(s) 110. HVAC or Heat Pump Thermostats 110.2(b), 110.2(c) No Furnace Standby Loss Control 110.2(d) No No Low Leakage AHU s 110.2(f) Yes 110.2(f) If using in performance calculations, must meet HERS verification requirements. Ventilation (design requirements) 120.1(b) No Exception #5 Occupant Sensor Ventilation Controls an alternative if space 1,500 ft 2 Demand Control Ventilation (DCV) 120.1(c)4 No No Occupant Sensor Ventilation Controls Shutoff and Reset Controls (New: occupancy sensors) 120.1(c)5, 120.2(e)3 Yes Multipurpose rooms 1,000 ft 2 Classrooms > 750 ft 2 Conference, convention, auditorium and meeting centers >750 ft 2 Exception: Demand control ventilation 120.2(e) No 120.2(e)3 Occupancy sensors that automatically setup the operating cooling and heating temperature by 2 in the following spaces: Multipurpose rooms 1,000 ft 2 Classrooms > 750 ft 2 Conference, convention, auditorium and meeting centers >750 ft 2 Exceptions: Dusts/fumes/vapors/gasses present, 24 hour facility, will not decrease overall energy use, systems 2 kw with shut off switch, DCV Outdoor Air and Exhaust Damper 120.2(f) No No Control Isolation Zones 120.2(g) No No Automatic Demand Shed Controls 120.2(h) No 120.2(h)5 Added features to controls for facility operators and that demand shed control are automated upon signal from utilities, not manual. Economizer FDD 120.2(i) Yes 120.2(i) Air cooled unitary DX units with economizers and cooling capacity 54,000 BTUH or higher, must include fault detection and diagnostic system. Duct Insulation No No 29

30 What s New: Complex HVAC Systems Measure T 24 New Changed Sections Heating hot water, cooling chilled and condenser water equipment efficiency Open and closed circuit cooling towers: Conductivity or flow based controls Max. achievable cycles of concentration Flow meter and analog output No 110.2(e) (e) (e)3 Yes Mandatory Measures Notes Open and closed circuit cooling towers have conductivity or flow based controls and are equipped with a Flow Meter, Overflow Alarm and Efficient Drift Eliminators. Determine maximum cycles based on a Langelier Saturation Index (LSI) of 2.5 or less. Building owner shall document maximum cycles of concentration on the mechanical compliance form which shall be reviewed and signed by the Professional Engineer (P.E.) of Record. Be equipped with a Flow Meter with an analog output for flow either hardwired or available through a gateway on the makeup water line. Overflow alarm 110.2(e)4 Be equipped with an Overflow Alarm to prevent overflow of the sump in case of makeup water valve failure. Overflow alarm shall send an audible signal or provide an alert via the Energy Management Control System to the tower operator in case of sump overflow. Efficient Drift Eliminators 110.2(e)5 Be equipped with Efficient Drift Eliminators that achieve drift reduction to percent of the circulated water volume for counter flow towers and percent for cross flow towers. Pipe Insulation Yes See updated Table A Commercial Boilers Yes Boilers meet the requirements of this section, as required: (a) combustion air positive shut off for boilers with input capacity of 2.5 MMBtu/y and above, (b) combustion air fan motors 10 hp or larger have variable speed drive or controls to limit fan motor demand to no more than 30% of total design wattage at 50% of design air volume, and (c) boilers with input capacity of 5 MMBtu/h and greater maintain excess oxygen concentrations at less than or equal to 5.0%. Prescriptive Measures Cooling Towers 140.4(h)2 No Fan Controls 140.4(h)5 Flow Controls 140.4(h)3 Yes Open cooling towers with multiple condenser water pumps are designed so that all cells can run in parallel with the larger of A) flow this is produced by the smallest pump or B) 50% of the design flow for the cell. Centrifugal Fan Cooling Towers 140.4(h)4 Yes Revised Table G performance requirements. Minimum Chiller Efficiency 140.4(i) Yes Chillers shall meet or exceed Path B from TABLE D Air Cooled Chiller Limitations 140.4(j) Yes Chilled water plants shall not have more than 300 tons provided by air cooled chillers. Hydronic System Measures 140.4(k) No No Change from 2008 to 2013 standards Changed from 2008 to 2013 standards Brand new with 2013 standards 30

31 NRCC-MCH-02-E: Wet Systems New Mandatory: Over 150 tons. Documentation of max. achievable cycles of concentration with calculator approved by CEC, then approved and signed by P.E. of record. 31

32 Prescriptive Measures Mandatory Measures Two Ways to Comply with the Standards Prescriptive Approach ENV some tradeoff MECH no tradeoff No tradeoffs between ENV, MECH, and LTG LTG some tradeoff Performance Approach Standard Design Proposed Design Tradeoffs ENV MECH LTG * * See notes for restrictions

33 Climate Zone Prescriptive requirements based on climate zone 33

34 NRCC-MCH-02-E: Dry Systems Required when total cooling capacity over 54,000 BTUH (Or trade off with higher efficiency per Table A, which is 65% for CZ4). Dew Point, Fixed Enthalpy, Electronic Enthalpy and Differential Enthalpy Controls not allowed (only Fixed and Differential Dry Bulb and Fixed Enthalpy+drybulb). Air Economizer Construction If cooling fan system over 45,000 BTUH, factory warranty, testing, minimized air and return damper leakage, fixed controls to have adjustable setpoint, calibration, high limit sensor location correct, relief air to not over-pressurize building. Minimum compressor unloading 100% open for mechanical cooling, not close until leaving temp less than 45 F DX Constant volume system: 2 stage control 75,000 BTUH DX Variable volume system: 3 stage control 65,000 & 240,000 BTUH 4 stage control 240,000 BTUH These motors shall have the means to adjust motor speed for either balancing or remote control. Belt-driven fans may use sheave adjustments for airflow balancing in lieu of a varying motor speed. 34

35 Measure What s New: HVAC Dry System Measures T 24 Sections New Changed Notes Prescriptive Measures Equipment is sized in 140.4(a & b) No conformance with (a & b) Supply Fan Pressure Control (c ) 140.4(c )4 These motors shall have the means to adjust motor speed for either balancing or remote control. Belt driven fans may use sheave adjustments for airflow balancing in lieu of a varying motor speed. Simultaneous Heat/Cool 140.4(d) 140.4(d)A.iii and First and second stage of heating dead band iv Economizer 140.4(e) Yes Required when total cooling capacity over 54,000 BTUH (Or trade off with higher efficiency per Table A). Heat and Cool Air Supply Reset 140.4(f) No Electric Resistance Heating 140.4(g) No Dew Point, Fixed Enthalpy, Electronic Enthalpy and Differential Enthalpy Controls not allowed (only Fixed and Differential Dry Bulb and Fixed Enthalpy+drybulb). Air Economizer Construction If cooling fan system over 45,000 BTUH, factory warranty, testing, minimized air and return damper leakage, fixed controls to have adjustable setpoint, calibration, high limit sensor location correct, relief air to not over pressurize building. Minimum compressor unloading 100% open for mechanical cooling, not close until leaving temp less than 45 F DX Constant volume system: 2 stage control 75,000 BTUH DX Variable volume system: 3 stage control 65,000 & 240,000 BTUH 4 stage control 240,000 BTUH Duct Leakage Sealing and Testing (l) New vs. altered New (tested at 6%): 75% duct work replaced Only if the reused parts are accessible and can be sealed to prevent leakage. New air handler and 75% altered ducts is a New/Replacement HVAC system. Altered (tested at 15%): 75% duct work replaced Altered ducts must meet BOTH the less than 15% of system fan flow leakage rate AND less than 10% leakage to outside (instead of either/or). Complying by reducing duct leakage by more than 60% no longer will be an option. Indoor Fan Airflow Control 140.4(m) Yes 140.4(m) Indoor Fan Airflow Control (variable speed drive): DX Cooling: 75,000 BTUH; 65,000 BTUH after 1/1/2016 No Change from 2008 to 2013 standards Changed from 2008 to 2013 standards Brand new with 2013 standards 35

36 HERS Duct Testing All new ducts (75% or more of new) sealed to a leakage rate not to exceed 6% of fan flow Existing ducts (less than 75% of new ducts) Sealed to a leakage rate not to exceed 15% of fan flow Connected to constant volume, single zone, air conditioners, heat pumps or furnaces; and Serves floor area of < 5,000 sq ft ; and Has >25% duct surface area located in one or more of these spaces: Outdoors; or Directly under a roof where U-factor of roof is >U-factor of ceiling; or Directly under a roof in which the U-factor does not meet prescriptive requirements and insulation not in contact with continuous roof or drywall ceiling; or Directly under a roof with fixed vents or openings to outside or unconditioned spaces; or Unconditioned crawlspace; or other unconditioned spaces.

37 What s New: Complex HVAC Systems Measure T 24 New Changed Sections Heating hot water, cooling chilled and condenser water equipment efficiency Open and closed circuit cooling towers: Conductivity or flow based controls Max. achievable cycles of concentration Flow meter and analog output No 110.2(e) (e) (e)3 Yes Mandatory Measures Notes Open and closed circuit cooling towers have conductivity or flow based controls and are equipped with a Flow Meter, Overflow Alarm and Efficient Drift Eliminators. Determine maximum cycles based on a Langelier Saturation Index (LSI) of 2.5 or less. Building owner shall document maximum cycles of concentration on the mechanical compliance form which shall be reviewed and signed by the Professional Engineer (P.E.) of Record. Be equipped with a Flow Meter with an analog output for flow either hardwired or available through a gateway on the makeup water line. Overflow alarm 110.2(e)4 Be equipped with an Overflow Alarm to prevent overflow of the sump in case of makeup water valve failure. Overflow alarm shall send an audible signal or provide an alert via the Energy Management Control System to the tower operator in case of sump overflow. Efficient Drift Eliminators 110.2(e)5 Be equipped with Efficient Drift Eliminators that achieve drift reduction to percent of the circulated water volume for counter flow towers and percent for cross flow towers. Pipe Insulation Yes See updated Table A Commercial Boilers Yes Boilers meet the requirements of this section, as required: (a) combustion air positive shut off for boilers with input capacity of 2.5 MMBtu/y and above, (b) combustion air fan motors 10 hp or larger have variable speed drive or controls to limit fan motor demand to no more than 30% of total design wattage at 50% of design air volume, and (c) boilers with input capacity of 5 MMBtu/h and greater maintain excess oxygen concentrations at less than or equal to 5.0%. Prescriptive Measures Cooling Towers 140.4(h)2 No Fan Controls 140.4(h)5 Flow Controls 140.4(h)3 Yes Open cooling towers with multiple condenser water pumps are designed so that all cells can run in parallel with the larger of A) flow this is produced by the smallest pump or B) 50% of the design flow for the cell. Centrifugal Fan Cooling Towers 140.4(h)4 Yes Revised Table G performance requirements. Minimum Chiller Efficiency 140.4(i) Yes Chillers shall meet or exceed Path B from TABLE D Air Cooled Chiller Limitations 140.4(j) Yes Chilled water plants shall not have more than 300 tons provided by air cooled chillers. Hydronic System Measures 140.4(k) No No Change from 2008 to 2013 standards Changed from 2008 to 2013 standards Brand new with 2013 standards 37

38 Min. Chiller Efficiencies: Table D Both full load (EER) and IPLV minimums required. New Mandatory efficiency requirements: Path B Both full load (EER) and IPLV minimums required. New Prescriptive efficiency requirements: Path A 38

39 Covered Processes 3/13/2014

40 CEC Blueprint 40

41 Refrigerated Warehouses: Mandatory Coolers are defined as refrigerated spaces cooled between 32 degree F (0 o C) and 55 degree F (13 o C). Freezers are defined as refrigerated spaces cooled below 32 o F (0 o C). The 2008 Title 24 Building Energy Efficiency Standards do not address walk-in refrigerators and freezers, as these are covered by the Title 20 Appliance Efficiency Regulations. A walk-in refrigerator or freezer is defined as a refrigerated space less than 3000 ft2 in floor area. 41

42 What s New: Covered Processes (Refrigerated Warehouse) Measure T 24 New Chang Notes Section ed Mandatory Refrigerated Warehouse Insulation 120.6(a)1 Yes Table A Underslab Heating 120.6(a)2 No Evaporators 120.6(a)3 Yes A. Single phase fan motors less than 1 hp and less than 460 Volts in newly installed evaporators shall be electronically commutated motors or shall have a minimum motor efficiency of 70 percent when rated in accordance with NEMA Standard MG at full load rating conditions. B. Evaporator fans served either by a suction group with multiple compressors, or by a single compressor with variable capacity capability shall be variable speed and the speed shall be controlled in response to space temperature or humidity. C. Evaporator fans served by a single compressor that does not have variable capacity shall utilize controls to reduce airflow by at least 40 percent for at least 75 percent of the time when the compressor is not running. Exceptions may apply Condensers 120.6(a)4 Yes New language: E. Condensing temperature reset. The condensing temperature set point of systems served by air cooled condensers shall be reset in response to ambient drybulb temperature. The condensing temperature set point of systems served by evaporative cooled condensers or water cooled condensers (via cooling towers or fluid coolers) shall be reset in response to ambient wetbulb temperatures. F. Fan powered condensers shall meet the condenser efficiency requirements listed in TABLE B. Condenser efficiency is defined as the Total Heat of Rejection (THR) capacity divided by all electrical input power including fan power at 100 percent fan speed, and power of spray pumps for evaporative condensers. G. Air cooled condensers shall have a fin density no greater than 10 fins per inch. Exceptions may apply Compressors 120.6(a)5 Yes New language: B. New open drive screw compressors in new refrigeration systems with a design saturated suction temperature (SST) of 28 F or lower that discharges to the system condenser pressure shall control compressor speed in response to the refrigeration load. C. New screw compressors with nominal electric motor power greater than 150 HP shall include the ability to automatically vary the compressor volume ratio (Vi) in response to operating pressures. Exceptions may apply Infiltration Barriers Refrigeration System Acceptance 120.6(a)6 Yes Passageways between freezers and higher temperature spaces, and passageways between coolers and nonrefrigerated spaces, shall have an infiltration barrier consisting of strip curtains, an automatically closing door, or an air curtain designed by the manufacturer for use in the passageway and temperature for which it is applied. Exceptions may apply 120.6(a)7 Yes Before an occupancy permit is granted for a new refrigerated warehouse, or before a new refrigeration system serving a refrigerated warehouse is operated for normal use, the following equipment and systems shall be certified as meeting the Acceptance Requirements for Code Compliance. 42

43 Refrigeration: Mandatory Retail food stores with 8,000 sq. ft. or more of conditioned area: Fan Powered condensers meet requirements of 120.6(b)1 Compressors meet requirements of 120.6(b)2 Lighting in refrigerated display cases and lights on glass doors (120.6(b)3) Automatic time switch controls to turn off lights during non-business hours Motion sensor controls on each case that reduce lighting power by at least 50% within 30 minutes after the area near the case is vacated Refrigeration heat recovery per 120.6(b)4 43

44 Measure T 24 Section Retail Stores with Commercial Refrigeration Condensers serving refrigeration systems. Compressor Systems. Refrigerated Display Cases. New What s New: Covered Processes (Retail Stores) Notes Mandatory 120.6(b) Yes Retail food stores with 8,000 square feet or more of conditioned area, and that utilize either: refrigerated display cases, or walk in coolers or freezers connected to remote compressor units or condensing units, shall meet the requirements of Subsections 1 through 4. Exceptions may apply A. All condenser fans for air cooled condensers, evaporative cooled condensers, air or water cooled fluid coolers or cooling towers shall be continuously variable speed, with the speed of all fans serving a common condenser high side controlled in unison. B. The refrigeration system condenser controls for systems with air cooled condensers shall use variablesetpoint control logic to reset the condensing temperature setpoint in response to ambient drybulb temperature. C. The refrigeration system condenser controls for systems with evaporative cooled condensers shall use variable setpoint control logic to reset the condensing temperature setpoint in response to ambient wetbulb temperature. D. The minimum condensing temperature setpoint shall be less than or equal to 70 F. E. Fan powered condensers shall meet the specific efficiency requirements listed in Table C. F. Air cooled condensers shall have a fin density no greater than 10 fins per inch. A. Compressors and multiple compressor suction groups shall include control systems that use floating suction pressure logic to reset the target saturated suction temperature based on the temperature requirements of the attached refrigeration display cases or walk ins. B. Liquid subcooling shall be provided for all low temperature compressor systems with a design cooling capacity equal or greater than 100,000 Btu/hr with a design saturated suction temperature of 10 F or lower, with the subcooled liquid temperature maintained continuously at 50 F or less at the exit of the subcooler, using compressor economizer port(s) or a separate medium or high temperature suction group operating at a saturated suction temperature of 18 F or higher. Lighting in refrigerated display cases, and lights on glass doors installed on walk in coolers and freezers shall be controlled by one of the following: Refrigeration Heat Recovery. A. Automatic time switch controls to turn off lights during nonbusiness hours. Timed overrides for any line up or walk in case may only be used to turn the lights on for up to one hour. Manual overrides shall time out automatically to turn the lights off after one hour. B. Motion sensor controls on each case that reduce display case lighting power by at least 50 percent within 30 minutes after the area near the case is vacated. A. HVAC systems shall utilize heat recovery from refrigeration system(s) for pace heating, using no less than 25 percent of the sum of the design Total Heat of Rejection of all refrigeration systems that have individual Total Heat of Rejection values of 150,000 Btu/h or greater at design conditions. B. The increase in hydrofluorocarbon refrigerant charge associated with refrigeration heat recovery equipment and piping shall be no greater than 0.35 lbs per 1,000 Btu/h of heat recovery heating capacity. No Change from 2008 to 2013 standards Changed from 2008 to 2013 standards Brand new with 2013 standards 44

45 Parking Garage: Mandatory Lighting 1. General lighting to be controlled by occupancy sensing controls having at least one control step between 20% and 50% of design lighting power. 2. Combined total of 36 sf or more openings, luminaires for general lighting in primary and secondary sidelite zones to be controlled independently by multi level (continuous dimming or on/off) automatic controls. 3. When primary sidelit zone illuminance level greater than 150% of that provided by electric lighting, controls HVAC must reduce controlled power to zero. 1. Automatically detect contaminant levels and stage fans or modulate fan airflow rates to 50% or less of design capacity provided acceptable contaminant levels are maintained. 2. Have controls and/or devices that will result in fan motor demand of no more than 30% of design wattage at 50% of design airflow. 3. CO sensor for every 5,000 sf, at least 2 sensors per proximity zone. 4. CO concentration maintained at 25 ppm or less at all times. 5. Ventilation rate be at least 0.15 cfm/sf when garage occupied. 6. System shall maintain the garage at negative or neutral pressure relative to other occupied spaces when garage occupied. 45

46 Measure T 24 Section New Changed What s New: Covered Processes (Parking Garage) Notes Mandatory Garage Exhaust: Exhaust Fan Control 120.6(c)1&2 Yes Automatically detect contaminant levels and stage fans or modulate fan airflow rates to 50 percent or less of design capacity provided acceptable contaminant levels are maintained. Have controls and/or devices that will result in fan motor demand of no more than 30 percent of design wattage at 50 percent of design airflow. CO Sensor Location 120.2(c)3 CO shall be monitored with at least one sensor per 5,000 square feet, with the sensor located in the highest expected concentration locations, with at least two sensors per proximity zone. A proximity zone is defined as an area that is isolated from other areas either by floor or other impenetrable obstruction. CO Senor Setpoint Min. Ventilation 120.2(c)4 CO concentration at all sensors is maintained at 25 ppm or less at all times (c)5 The ventilation rate shall be at least 0.15 cfm/ft2 when the garage is scheduled to be occupied. Garage 120.2(c)6 Pressurization CO Sensor 120.2(c)7 Requirements The system shall maintain the garage at negative or neutral pressure relative to other occupiable spaces when the garage is scheduled to be occupied. CO sensors shall be certified by the manufacturer to be accurate within plus or minus 5 percent of measurement, factory calibrated, and certified by the manufacturer to drift no more than 5 percent per year, certified by the manufacturer to require calibration no more frequently than once a year, monitored by a control system. Ventilation Acceptance Testing 120.2(c)8 A Certificate of Acceptance shall be submitted to the enforcement agency that certifies that the equipment and systems meet the acceptance requirements specified in NA7.12. No Change from 2008 to 2013 standards Changed from 2008 to 2013 standards Brand new with 2013 standards 46

47 Process Boilers: Mandatory 1. Combustion air positive shut-off shall be provided on all newly installed process boilers as follows: A. All process boilers with an input capacity of 2.5 MMBtu/h (2,500,000 Btu/h) and above, in which the boiler is designed to operate with a non-positive vent static pressure. B. All process boilers where one stack serves two or more boilers with a total combined input capacity per stack of 2.5 MMBtu/h (2,500,000 Btu/h). 2. Process boiler combustion air fans with motors 10 horsepower or larger shall meet one of the following for newly installed boilers: A. The fan motor shall be driven by a variable speed drive; or B. The fan motor shall include controls that limit the fan motor demand to no more than 30 percent of the total design wattage at 50 percent of design air volume. 3. Newly installed process boilers with an input capacity of 5 MMBtu/h (5,000,000 Btu/h) to 10 MMBtu/h (10,000,000 Btu/h) shall maintain excess (stack-gas) oxygen concentrations at less than or equal to 5.0 percent by volume on a dry basis over firing rates of 20 percent to 100 percent. 4. Newly installed process boilers with an input capacity greater than 10 MMBtu/h (10,000,000 Btu/h) shall maintain excess (stack-gas) oxygen concentrations at less than or equal to 3.0 percent by volume on a dry basis over firing rates of 20 percent to 100 percent. 47

48 Compressed Air: Mandatory All new compressed air systems where total combined online horsepower of the compressor is 25 hp or more: Equipped with appropriate sized trim compressor and primary storage to provide acceptable performance across the range of the systems and to avoid control gaps One or more variable speed drive compressors per 120.6(e) 1A Include a compressors or set of compressors with total effective trim capacity at least the size of the largest net capacity increment between combinations of compressors, or the size of the smallest compressor, whichever is larger per 12.6 (e) 1B Controls of combined system with a hp rating of more than 100 hp have specific control requirements per (e) 2 A certificate of acceptance submitted to building inspector that certifies that the equipment and systems meet the acceptance requirements of NA7.13 before occupancy permit granted. 48

49 Measure T 24 Section Process Boilers Combustion air What s New: Covered Processes (Boilers & Compressed Air) New Changed Mandatory Notes 120.2(d)1 Yes Combustion air positive shut off shall be provided on all newly installed process boilers as follows: A. All process boilers with an input capacity of 2.5 MMBtu/h (2,500,000 Btu/h) and above, in which the boiler is designed to operate with a non positive vent static pressure. B. B. All process boilers where one stack serves two or more boilers with a total combined input capacity per stack of 2.5 MMBtu/h (2,500,000 Btu/h). Fan Motors 120.2(d)2 Process boiler combustion air fans with motors 10 horsepower or larger shall meet one of the following for newly installed boilers: A. The fan motor shall be driven by a variable speed drive; or B. B. The fan motor shall include controls that limit the fan motor demand to no more than 30 percent of the total design wattage at 50 percent of design air volume. Stackgas 120.2(d)3,4 Oxygen Concentrati ons Newly installed process boilers with an input capacity of 5 MMBtu/h (5,000,000 Btu/h) to 10 MMBtu/h (10,000,000 Btu/h) shall maintain excess (stackgas) oxygen concentrations at less than or equal to 5.0 percent by volume on a dry basis over firing rates of 20 percent to 100 percent. Combustion air volume shall be controlled with respect to firing rate or measured flue gas oxygen concentration. Use of a common gas and combustion air control linkage or jack shaft is prohibited. Newly installed process boilers with an input capacity greater than 10 MMBtu/h (10,000,000 Btu/h) shall maintain excess (stack gas) oxygen concentrations at less than or equal to 3.0 percent by volume on a dry basis over firing rates of 20 percent to 100 percent. Combustion air volume shall be controlled with respect to measured flue gas oxygen concentration. Use of a common gas and combustion air control linkage or jack shaft is prohibited. Compressed Air 120.2(e) Yes All new compressed air systems, and all additions or alterations of compressed air systems where the total combined online horsepower (hp) of the compressor(s) is 25 horsepower or more shall meet the requirements of Subsections 1 through 3. These requirements apply to the compressors and related controls that provide compressed air and do not apply to any equipment or controls that use or process the compressed air. No Change from 2008 to 2013 standards Changed from 2008 to 2013 standards Brand new with 2013 standards 49

50 Computer Rooms: Prescriptive Economizers A. Integrated air economizer capable of providing 100% of the expected system cooling load at outside temperatures of 55 F and below; OR B. Integrated water economizer capable of providing 100% of the expected system cooling load at outside temperatures of 40 F and below. Exception: Individual computer room under 5 tons in a building that has no economizers. 2. Reheat: Controls that prevent reheating, recooling, and simultaneous provisions of heating and cooling to the same zone. 3. Humidification: Non-adiabatic humidification (steam, infrared) prohibited. Only adiabatic humidification permitted (direct evaporation, ultrasonic) 4. Fan power: Not to exceed 27 w/kbtuh of net sensible cooling capacity. 5. Fan control: 2-speed or variable sped control that will result in fan motor demand of no more than 50% of design wattage at 66% of design fan speed. 6. Containment: if air-cooled, design load exceeding 175 kw/room, air barriers to prevent discharge air to recirculate back to computer inlets through cooling system. 50

51 Kitchen Exhaust: Prescriptive Requirements for Commercial Kitchens. 1. Kitchen exhaust systems. a. Replacement air introduced directly into the hood cavity of kitchen exhaust hoods shall not exceed 10percent of the hood exhaust airflow rate. b. For kitchen/dining facilities having total Type I and Type II kitchen hood exhaust airflow rates greater than 5,000 cfm, each Type I hood shall have an exhaust rate that complies with TABLE A. If a single hood or hood section is installed over appliances with different duty ratings, then the maximum allowable flow rate for the hood or hood section shall not exceed the TABLE A values for the highest appliance duty rating under the hood or hood section. Refer to ASHRAE Standard for definitions of hood type, appliance duty and next exhaust flow rate. EXCEPTION 1 to Section 140.9(b)1B: 75 percent of the total Type I and Type II exhaust replacement air is transfer air that would otherwise be exhausted. EXCEPTION 2 to Section 140.9(b)1B: Existing hoods not being replaced as part of an addition or alteration. Course Title 3/13/

52 Kitchen Ventilation: Prescriptive 2. Kitchen ventilation. A. Mechanically cooled or heated makeup air delivered to any space with a kitchen hood shall not exceed the greater of: i. The supply flow required to meet the space heating and cooling load; or ii. The hood exhaust flow minus the available transfer air from adjacent spaces. Available transfer air is that portion of outdoor ventilation air serving adjacent spaces not required to satisfy other exhaust needs, such as restrooms, not required to maintain pressurization of adjacent spaces, and that would otherwise be relieved from the building. EXCEPTION to Section 140.9(b)2A: Existing kitchen makeup air units not being replaced as part of an addition or alteration. B. A kitchen/dining facility having a total Type I and Type II kitchen hood exhaust airflow rate greater than 5,000 cfm shall have one of the following: i. At least 50 percent of all replacement air is transfer air that would otherwise be exhausted; or ii. Demand ventilation system(s) on at least 75 percent of the exhaust air. Such systems shall: a. Include controls necessary to modulate airflow in response to appliance operation and to maintain full capture and containment of smoke, effluent and combustion products during cooking and idle; and b. Include failsafe controls that result in full flow upon cooking sensor failure; and c. Include an adjustable timed override to allow occupants the ability to temporarily override the system to full flow; and d. Be capable of reducing exhaust and replacement air system airflow rates to the larger of: (i) 50 percent of the total design exhaust and replacement air system airflow rates; or (ii) The ventilation rate required per Section iii. Listed energy recovery devices with a sensible heat recovery effectiveness of not less than 40 percent on at least 50 percent of the total exhaust airflow; and iv. A minimum of 75 percent of makeup air volume that is: a. Unheated or heated to no more than 60 F; and b. Uncooled or cooled without the use of mechanical cooling. EXCEPTION to Section 140.9(b)2B: Existing hoods not being replaced as part of an addition or alteration. Course Title 3/13/

53 Measure T 24 Section Commercial Kitchen: Bypass Hood Exhaust and MAU Type I/II Hood Exhaust Mechanically heated or cooled make up air Demand Ventilations Systems 140.9(b)1A 140.9(b)1B 140.9(b)2A 140.9(b)2Bii What s New: Covered Processes (Kitchen) New Changed Notes Yes Prescriptive Measures Replacement air introduced directly into the hood cavity of kitchen exhaust hoods shall not exceed 10% of the hood exhaust airflow rate. For kitchen/dining facilities having total Type I and Type II kitchen hood exhaust airflow rates greater than 5,000 cfm, each Type I hood shall have an exhaust rate that complies with TABLE A. Mechanically cooled or heated makeup air delivered to any space with a kitchen hood shall not exceed the greater of: i. The supply flow required to meet the space heating and cooling load; or ii. The hood exhaust flow minus the available transfer air from adjacent spaces. Demand ventilation system(s) on at least 75 percent of the exhaust air. Such systems shall: a. Include controls necessary to modulate airflow in response to appliance operation and to maintain full capture and containment of smoke, effluent and combustion products during cooking and idle; and b. Include failsafe controls that result in full flow upon cooking sensor failure; and c. Include an adjustable timed override to allow occupants the ability to temporarily override the system to full flow; and d. Be capable of reducing exhaust and replacement air system airflow rates to the larger of: (i) 50 percent of the total design exhaust and replacement air system airflow rates; or (ii) The ventilation rate required per Section Energy Recovery Systems 120.9(b)2Biii Listed energy recovery devices with a sensible heat recovery effectiveness of not less than 40 percent on at least 50 percent of the total exhaust airflow. Tempered/Non 140.9(b)2Biv Mechanical Cooling Air Systems A minimum of 75 percent of makeup air volume that is: a. Unheated or heated to no more than 60 F; and b. Uncooled or cooled without the use of mechanical cooling. EXCEPTION to Section 140.9(b)2B: Existing hoods not being replaced as part of an addition or alteration. No Change from 2008 to 2013 standards Changed from 2008 to 2013 standards Brand new with 2013 standards 53

54 Laboratory Exhaust: Prescriptive Requirements for Laboratory exhaust systems. For buildings with laboratory exhaust systems where the minimum circulation rate to comply with code or accreditation standards is 10 ACH or less, the design exhaust airflow shall be capable of reducing zone exhaust and makeup airflow rates to the regulated minimum circulation rate, or the minimum required to maintain pressurization requirements, whichever is larger. Variable exhaust and makeup airflow shall be coordinated to achieve the required space pressurization at varied levels of demand and fan system capacity. EXCEPTION 1 to Section 140.9(c): Laboratory exhaust systems serving zones where constant volume is required by the Authority Having Jurisdiction, facility Environmental Health & Safety department or other applicable code. EXCEPTION 2 to Section 140.9(c): New zones on an existing constant volume exhaust Course Title 3/13/

55 Measure T 24 Section What s New: Covered Processes (Computer Rooms) New Changed Notes Prescriptive Measures Computer Rooms Yes Each individual cooling system primarily serving computer room(s) shall include either: Economizers 140.9(a)1 A. An integrated air economizer capable of providing 100 percent of the expected system cooling load B. An integrated water economizer capable of providing 100 percent of the expected system cooling load Exceptions may apply Reheat 140.9(a)2 Each computer room zone shall have controls that prevent reheating, recooling and simultaneous provisions of heating and cooling to the same zone, such as mixing or simultaneous supply of air that has been previously mechanically heated and air that has been previously cooled, either by cooling equipment or by economizer systems. Humidification 140.9(a)3 Nonadiabatic humidification (e.g. steam, infrared) is prohibited. Only adiabatic humidification (e.g. direct evaporative, ultrasonic) is permitted. Fan Power 140.9(a)4 The total fan power at design conditions of each fan system shall not exceed 27 W/kBtu hof net sensible cooling capacity. Fan Control 140.9(a)5 Each unitary air conditioner with mechanical cooling capacity exceeding 60,000 Btu/hr and each chilled water fan system shall be designed to vary the airflow rate as a function of actual load and shall have controls and/or devices (such as two speed or variable speed control) that will result in fan motor demand of no more than 50 percent of design wattage at 66 percent of design fan speed. Containment 140.9(a)6 Computer rooms with air cooled computers in racks and with a design load exceeding 175 kw/room shall include air barriers such that there is no significant air path for computer discharge air to recirculate back to computer inlets without passing through a cooling system. Exceptions may apply No Change from 2008 to 2013 standards Changed from 2008 to 2013 standards Brand new with 2013 standards 55

56 Electrical 3/13/2014

57 Service Metering Projects are required to provide an electric meter that permits the building owner or manager to read the instantaneous power in kilowatts being used by the building, and to be able to reset and measure energy use in kilowatt-hours over a period of his own choosing. Minimum metering requirements per Table A. 57

58 Disaggregation 58

59 Power Distribution Voltage Drop Voltage Drop The recommended voltage drop limits from the California Electrical Code (Title 24 Part 3) become mandatory. The voltage drop in feeders is limited to 2% of design load; and The voltage drop in branch circuits is limited to 3% of design load. Emergency power circuits are exempt. Suggested Calculation Approach Voltage drop calculations are of two principal types: Voltage drop in feeders, which are conductors carrying current from one switchboard or panelboard to another; and Voltage drop in branch circuits, which are conductors carrying current from a switchboard or panelboard to one or more connected loads. 59

60 Circuit Control 60

61 Energy Code Ace New Website!

62 One-Stop Shop Tools Resources Learning Portal News & Information Recognition Opportunities Personalized Recommendations Engaging Point Tracking lists 62

63 Stack your deck with Aids in determining which compliance forms are applicable to your specific project Helps you navigate the Standards using key word search capabilities, hyperlinked tables and related sections A field guide to assist you in identifying proper installation techniques - Coming Soon! Traditional Classroom Courses Offered at utility training centers and on-site in local jurisdictions we ll come to you! Virtual Classroom Courses Interactive instructor-led online classes Online Self-Studies Take them when and where you like at your own pace Decoding Talk Series Facilitated online discussions for Building Inspectors Fact Sheets Summaries of key requirements, definitions and resources useful for Title 24, Part 6 implementation Trigger Sheets Summaries of sections of Title 24, Part 6 that are triggered based on project scope. Checklists Coming Soon! FAQs Coming Soon! Useful Links Coming Soon! Workshop packages to help Building Departments facilitate trainings for local installation contractors All tools, training and resources are offered free of charge

64 New Series Free, 90-minute, online discussion on a specific topic for Building Department Personnel Designed to offer and gather information on technical aspects of the code, best practices and challenges Code experts guide a discussion based on the answers building department personnel give to questions asked at registration Sample subjects: Let s Talk Nonresidential Indoor Mandatory Lighting Controls for Building Inspectors Let s Talk Residential HVAC Changeouts for Building Inspectors Let s Talk Residential Insulation for Building Inspectors 64

65 Thank you Statewide Compliance Improvement Team: Jill Marver, PG&E Javier Mariscal, SCE Gary Shushnar, SCE Adrian Salas, SDG&E Phil Pratt, So Cal Gas Co. Contact Role Phone Gina Rodda Presenter (510) ext 204 CEC Hotline (800) Jill Marver PG&E Course Manager (925)

66 SEPTEMBER - OCTOBER 2013 The 2013 Standards Will Go Into Effect January 1, 2014 The Blueprint is your guide to information, training and resources for the 2013 Building Energy Efficiency Standards. The California Energy Commission has partnered with the Statewide Codes & Standards Program to provide training and resources for building officials. California s building energy code can help save energy, keep our air cleaner and offset the need to build new power plants. We understand it can be quite technical and difficult to navigate new standards, especially when time and resources are limited. The Statewide Codes & Standards Program offers free energy code training, tools and resources for building department personnel, as well as others who need to understand and meet the requirements of Title 24, Part 6. Designed to improve compliance with the state s building energy code, the program aims to Fall 2013 Classroom Trainings Offered advance the adoption and effective implementation of energy efficiency measures and building practices to lock in long- term energy savings. The program recognizes that codes and standards are one of the most effective pathways to ensuring sustained market transformation. The key to making them work well is found in the enforcement efforts of building department professionals. Program offerings are designed for counter staff, plans examiners, field inspectors and building officials. The California Statewide Codes & Standards Program is funded by California utility customers under the auspices of the California Public Utilities Commission and implemented by Pacific Gas and Electric Company, San Diego Gas and Electric, Southern California Edison and Southern California Gas, in support of the California Energy Commission. Title 24 Residential or Nonresidential Standards Essentials for Plans Examiners & Building Inspectors Residential Lighting: Title 24 & Technology Update Retail Lighting: Title 24 and Technology Update Title 24 Standards Essentials for Supermarket Refrigeration Title 24 Standards Essentials for Residential AC Quality Installation Contractors Title 24 Standards Essentials for Small Commercial AC Quality Installation Contractors Courses are offered at utility energy training centers and at special locations upon request. For more information please wendy@mbaenergy.com. For scheduled classes, check these energy center websites to register: resource- center services/energy- education- centers

67 CALIFORNIA ENERGY COMMISSION PAGE 2 Decoding: Let s Talk Series for Building Officials Utilize these FREE 90- minute interactive online events to discuss and decode Title 24 Part 6 Nonresidential Indoor Mandatory Lighting Controls. These webinars will help you with Field Inspection preparation, time management, and dealing with non- compliant projects. Decoding Lighting: Let s Talk Nonresidential Indoor Mandatory Lighting Controls for Building Inspectors November 12, 8:00am 9:30am November 12, 3:00pm 4:30pm November 13, 8:00am 9:30am November 13, 3:00pm 4:30pm November 14, 8:00am 9:30am For more information on the Statewide Codes and Standards Program, please contact Jill Marver at JKZ1@pge.com. Free Tools and Resources In addition to trainings, the program provides free tools and resources to help make complying with Title 24 easier and more efficient. These can be found at and include: Fact Sheets & Trigger Sheets - Residential HVAC Changeouts, Cool Roofs Residential Re- Roofing, Residential Fenestration, and Commercial HVAC Alterations Reference Ace - helps you navigate the Title 24, Part 6 Standards documents using key word search capabilities along with hyperlinked tables and related sections available now, 2013 coming soon! Forms Ace aids in determining which Title 24, Part 6 Forms are applicable to your specific projects using a series of questions in order to determine the appropriate forms beta available now, 2013 coming soon! Feedback encouraged let us know what you think. Installation Ace (Coming Soon) a field guide to assist you in identifying proper installation techniques related to Title 24, Part 6 components and includes visual aids for some components that are commonly improperly installed Energy Standards documents are available online at

68 What's New for 2013 Non- Residential CALIFORNIA ENERGY COMMISSION PAGE 3 The process to develop the 2013 Standards began with a call for ideas in winter of 2010, moved through a series of IOU sponsored stakeholder meetings throughout the state, Energy Commission staff workshops and Energy Commission hearings in 2011 through 2012 and concluded at the adoption hearing on May 23, Energy Commission staff, contractors, utilities and many others participated in the process. The following paragraphs summarize the principle changes that resulted. All Buildings Revisions to the administrative sets the format and informational order for electronic compliance document registration and submittal and for electronic retention of compliance documentation, including the nonresidential forms, for future use and clarifies the roles and responsibilities of the documentation author and the responsible person describes the rules for approving compliance software, alternative component packages, exceptional methods, data registries and related data input software, or electronic document repositories describes the rules for reporting fenestration U- factor, SHGC, and VT (c)5 explains the requirements for the water heating recirculation loops serving multiple dwelling units, high- rise residential, hotel/motel, and nonresidential occupancies. 4. Revisions to now covers ballasts and luminaires and residential vacancy sensors. Non- Residential Buildings Envelope 1. Increased low- slope cool roof requirements (increase reflectance from 0.55 to 0.63 for new construction and alterations). ( 140.3(a)1Aia1) 2. Established a maximum air leakage rate (0.04 cfm/sf) except in mild climate zones. ( 140.3(a)9B) 3. Increased fenestration requirements to reduce solar gains and increase visual transmittance for daylighting; 0.36 U- factor, 0.25 SHGC, VT 0.42 for fixed windows; the numbers are different for operable windows and skylights. ( 140.3(a)5B,C & D) 4. Fenestration. The Standards now include Dynamic Glazing, Window Films and new maximum values for Visible Transmittance (VT). New Dynamic Glazing, Window Films requirements and changes are in the Reference Nonresidential Appendix NA6 and NA Added mandatory Roof insulation requirements and minimum insulation for demising walls. ( 110.8(e) & (f)) Lighting 1. Clarification and simplification of existing language; removing exceptions no longer relevant. ( , ) 2. Lighting control devices moving from Title 24 Part 6 to Title 20; lighting control systems shall now be acceptance tested for Title 24. ( 110.9(b) & 130.4(a)) 3. Nonresidential indoor lighting, advanced multi- level lighting controls (controllable ballasts) increased in granularity (in addition to ON/OFF, increasing from one intermediate level to three intermediate levels or continuous dimming), favoring dimmable ballasts for linear fluorescent lighting systems. These controls will allow precise and non- interruptive adjustment of lighting to match the available daylighting, and provide dimming and demand response function

69 CALIFORNIA ENERGY COMMISSION PAGE 4 throughout the building. ( 130.1(a) 2C) & 130.1(b) 4. Enhancing, modifying, and adding to the prescriptive and mandatory daylighting control requirements; daylighting language significantly simplified. ( 130.1(d) & ( 140.6(d)) 5. Requirements for demand responsive reduction of lighting power being applied to smaller spaces. ( 130.1(e)) 6. Mandatory Automated Lighting Controls and Switching Requirements in Warehouses and Libraries - Require the installation of occupancy sensors in warehouse aisle ways and open spaces, and library stack aisles. ( 130.1(c)6A & B) 7. Mandatory automated lighting controls and switching requirements for hotels and multifamily building corridors - Require the installation of occupancy sensors in corridors and stairwells in lodging and multifamily buildings. ( 130.1(c)6C) 8. New mandatory occupancy sensor and daylighting controls in parking garage spaces. ( 130.1(d)3) 9. Increased requirements for multi- level lighting controls for nonresidential outdoor lighting. ( 130.2(c)3B) 10. Alternate path to comply with existing outdoor lighting cutoff (shielding) requirements, phasing in the new Backlight, Uplight, Glare (BUG) requirements. ( 130.2(b)) 11. Reduction of allowed lighting power density for some nonresidential indoor and outdoor lighting applications. ( 140.6(c) and 140.7(d)) 12. Tailored lighting revisions - Reduce the allowed LPD for Floor Display, Wall Display, and Ornamental Lighting under the Tailored Compliance (c)3I, J & K) 13. Plug Load Circuit Controls - requiring automatic shut- off controls of electric circuits that serve plug loads, including task lightings, in office buildings. ( 130.5(d)1) 14. Hotel/Motel Guest Room Occupancy Controls for HVAC and lighting systems - would require installation of occupancy controls for HVAC equipment, and all lighting fixtures in hotel/motel guest rooms, including plug- in lighting. ( 120.2(e)4 & 130.1(c)8) 15. Reduction of threshold when lighting alterations must comply with the Standards, from when 50% of the luminaires are replaced, to when 10% of the luminaires are replaced. Consistent with proposed changes to ASHRAE ( 141.0(b)2I & J) Mechanical 1. Added requirements for Fan Control and Integrated Economizers. Packaged units down to 6 tons must be VAV with the ability to modulate cooling capacity to 20% of maximum. Economizers must also be able to modulate cooling capacity to match VAV units. ( 140.4(c) & (e)) 2. Reduced ability for HVAC systems to reheat conditioned air. ( 140.4(d)) 3. Increased chiller efficiency requirements, consistent with ASHRAE ( 140.4(i)) 4. Increased cooling tower energy efficiency and WATER Savings. ( 140.4(k)2) 5. Added requirements for commercial boiler combustion controls. ( 140.4(k)3) 6. Added acceptance tests for HVAC sensors and controls, including those for demand controlled ventilation. ( 120.5(a)) 7. Added efficiency requirements for small motors. ( 140.4(c)4) 8. Added credit for evaporative systems that meet the Western Cooling Efficiency Challenge (WCEC program to acknowledge high energy and water efficiency in evaporative systems). 9. Moving Fault Detection and Diagnostics (FDD) protocols for air temperature, economizers, damper modulation, and excess outdoor air to mandatory measures from the current compliance option. ( 120.2(i))

70 CALIFORNIA ENERGY COMMISSION PAGE Energy Standards documents are available online at Electrical 1. Added mandatory requirement for receptacle controls in private offices, open office areas, reception lobbies, conference rooms, kitchens, and copy rooms to automatically shut off task lighting and other plug loads when the area is not occupied. ( 130.5(d)) 2. Added mandatory requirement for electrical panels to be isolated by energy end use (e.g. lighting, HVAC, plug loads). ( 130.5(b)2) Covered Processes The 2013 Standards now cover some specific process energy applications, such as supermarket refrigeration, refrigerated warehouses, commercial kitchen ventilation requirements, laboratory exhaust, parking garage ventilation, compressed air, and computer rooms. Definitions for Covered Processes and Exempt Processes were added. Covered Processes are defined as processes for which there are listed requirements. All other processes are Exempt Processes. Specific requirements for Covered Processes are in separate sections ( Mandatory and Prescriptive). It should be noted that the HVAC equipment efficiencies in and also apply to Covered Processes. In the 2013 Standards, the Covered Processes include: 1. Increased mandatory requirements for refrigerated warehouses. ( 120.6(a)) 2. Added mandatory requirements for commercial supermarket refrigeration. ( 120.6(b)) 3. Added mandatory ventilation control requirements for parking garages. ( 120.6(c)) 4. Added mandatory requirements for process boilers. ( 120.6(d)) 5. Added mandatory requirements for storage and unloading for compressed air systems ( 120.6(e)) Added prescriptive requirements for HVAC systems serving computer rooms. ( 140.9(a) 6. Added prescriptive ventilation control requirements for commercial kitchens. ( 140.9(b)) 7. Added prescriptive requirements for variable air volume for laboratory exhaust systems. ( 140.9(c)) Solar Ready 1. Added mandatory requirements for nonresidential buildings (3 stories or less) to make provisions to more easily enable the future addition of solar electric or solar water heating systems. ( (a)4) Commissioning 1. Moved Part 11 commissioning requirements to Part 6 for energy- related building components. ( 120.8) 2. Added mandatory requirements for design- phase commissioning, which includes an early review of design intent documents and highlighting efficiency specifications in both construction documents and Standards compliance forms. ( 120.8(d)) Compliance Option Hybrid Evaporative Cooling Systems in Nonresidential Buildings

71 CALIFORNIA ENERGY COMMISSION PAGE 6 All compliance approaches What's New for 2013 Residential 1. Revisions to the administrative section sets the format and informational order for electronic compliance document registration and submittal and for electronic retention of compliance documentation for future use and clarifies the roles and responsibilities of the documentation author and the responsible person; describes the rules for approving compliance software, alternative component packages, exceptional methods, data registries and related data input software, or electronic document repositories describes the rules for reporting fenestration U- factor, SHGC, and VT (c)5 explains the requirements for the water heating recirculation loops serving multiple dwelling units, high- rise residential, hotel/motel, and nonresidential occupancies. 3. Revisions to now covers ballasts and luminaires and residential vacancy sensors. Mandatory Measures 1. Duct sealing in all climate zones (CZs). (Section 150.0(m)11) 2. Return duct design or fan power, airflow testing, and grill sizing requirements (Residential HVAC Quality Installation Improvements). (Section150.0(m)13) 3. Lighting Improving and clarifying the mandatory lighting requirements for all residential buildings including kitchens, bathrooms, dining rooms, utility rooms, garages, hall ways, bedrooms, and outdoor lighting. (Section150.0(k) 4. New luminaire efficacy levels in Table B 5. Hot water pipe insulation - Requires insulation on pipes ¾ inch and larger. (Section150.0(j)2Aii) 6. Solar Ready Measure 250 square feet of solar ready zone on single family roofs in subdivisions of 10 or more swelling units. (Section150.0(r)) 7. Walls with 2x6 framing and larger must have at least R- 19 insulation. (Section 150.0(c)2) 8. New mandatory U- factor of 0.58 for vertical fenestrations products and skylights. (Section 150.0(q)) 9. New third party HERS verifications requirement for Ventilation for Indoor Air Quality, ASHRAE 62.2 requirements. (Section 150.0(o)) Prescriptive Compliance 1. High Performance Windows Reducing the U- Factor to 0.32 and SHGC to 0.25 in most climate zones. (Section 150.1(c)3A) 2. Duct Insulation Raise minimum from R- 4.2 to R- 6.0 in climate zones 6, 7, and 8. (Section 150.1(c)9) 3. Night Ventilation Whole house fan required to be installed in climate zones 8 through 14; a Smart Vents and Night Breeze allowed as performance path alternatives. (Section 150.1(c)12) 4. Expand the Radiant Barrier requirements to climate zones 3, and 5 through 7. (Section 150.1(c)2) 5. Refrigerant charge and verification now expanded to include ducted package units, mini- splits, and other units. (Section 150.1(c)7) 6. Increase wall insulation to R15+4 in all CZs. (Section 150.1(c)1B)

72 CALIFORNIA ENERGY COMMISSION PAGE 7 Performance Compliance The modeling procedures and requirements for compliance software have been significantly modified for the 2013 Standards. All compliance software vendors must use a single modeling approach and a single interpretation of the performance compliance rules. This Compliance Manager software will be integrated into vendor- supplied compliance software that is certified by the Energy Commission. More information is available in the 2013 Residential ACM Approval Manual and the 2013 Residential ACM Reference Manual. Additions and Alterations 1. Simplified Compliance documentation requirements for small additions and alteration projects that do not involve a HERS measure. (Section (a)1C and Section (a)3C) 2. Simplified rules for both the prescriptive and performance paths for additions, alterations, and existing plus additions plus alterations. (Section 150.2(a) and (b)) The California Energy Commission welcomes your feedback on the Blueprint. Please contact Daniel Johnson at (916) or daniel.johnson@energy.ca.gov. CALIFORNIA ENERGY COMMISSION Standards Implementation Office 1516 Ninth St, MS- 26 Sacramento, CA (916) Need Help? Energy Standards Hotline (800) (toll- free in CA) Edmund G. Brown Jr. Governor Robert B. Weisenmiller Chairman Karen Douglas David Hochschild Andrew McAllister Janea A. Scott Commissioners CEC