planal vertical The ultimate modern statement room, Planal Vertical radiators and exciting, flexible way to make an impression

Transcription

1 planal vertical The ultimate modern statement for your room, Planal Vertical radiators provide a discrete, sophisticated new look and exciting, flexible way to make an impression while efficiency heating your room. 16VPH600 (technical information and valves from p. 31) p. 11

2 technical specifications & price list P r e m i e r R a n g e p. 31

3 basic heat-loss calculator According to EN 442, inlet water temperature 75 C, outlet water temperature 65 C, and room temperature is 20 C are assumed and all our heat output figures published in our publications are to EN442. The total heat output of the radiator you choose must compensate for the heat-loss of your room so that it will maintain the interior temperature at 20 C. The following calculation will give you indication of your heat-loss. If you would like to take into all the factors effecting the heat-loss then you must use more complicated heat-loss calculator that you can find at If you have limited space or very large room, you can always put more than one radiator per room. Preferably you should locate radiators, near windows and doors where heat-loss is highest. Measure your living room in meters : Height _m : Length_m : Depth_m ie : H:2.64m, L:3.65m, D:4.94m Calculate the volume of the room : H x L x D = Cubic meters ie : 2.64 x 3.65 x 4.94 = cubic meters Multiply by a coefficient for each desired room temperature : 42 : bedrooms (to achieve 18 C) 52 : bathrooms, wc, living, study, dining etc (to achieve 21 C) ie : living room 52, x 52 = 2,475 watts The heat-loss in the living room is 2,475 watts, but there are following factors we need to consider for a better result we need to add 10% for every factor given here below. - Outside walls, if it is corner room two outside walls which means (10% and 10%) - Northern aspect room - Ceiling height more than 2.7m - Excessive large windows - Single glaze - Outside temperature assumed as -1 C, but if you would like to assume -2 C add 10%, -4 C add another 10%, -10 C add another 10% ie : One outside wall, excessive window, 2,475 x 1.1 x 1.1 = 2970 watts or 2554 kcal or btu the final heat-loss calculation. Heat outputs are based on At:50 C with 75 C inlet / 65 C outlet water and 20 C room temperature. Heat-outputs of chrome multirails are reduced by 20% due to plated finish. Suffix "P" for mirror polished products, "W" for white, "B" for black, "C" for chrome, "P" for polished, "G" for Gold, SS for Stainless Steel 304 and MAT for brushed mat. Pipe centre measurements are incorporating pair of valve distance of 45mm each where applicable. Product Height Width Pipe Overall Heat Output List Price List Price Code Floor to pipe centre Centres Distance mm mm mm mm from wall Btu Watts buckingham DIN Column Chrome Gold 600/CL/250 5BE /CL/350 7BE /CL/500 10BE /CL/700 14BE , captiva Wall to pipe centre SS-Mat SS-Polished CV , , CV , , CV , Width Pipe centres Buckingham Captiva p. 32 (prices shown exclude VAT)

4 Product Height Width Pipe Overall Heat Output List Price Code Floor to pipe centre Centres Distance mm mm mm mm from wall Btu Watts planal - Vertical (*accessories from page 47) White 12VPS VPS VPS VPS VPS VPH VPH VPH VPH VPH VPS VPS VPS VPS VPS VPH VPH VPH VPH VPH VPS VPS VPS VPS VPS VPH VPH VPH VPH VPH VPS VPS VPS VPS VPS VPH VPH VPH VPH VPH VPS VPS VPS VPS VPS VPH VPH VPH VPH VPH VPS VPS VPS VPS VPS VPH VPH VPH VPH VPH (prices shown exclude VAT) p. 41

5 Height inches Height mm Watts Btu planal vertical single-vps REF. HEAT OUTPUTS TO EN442 = T 60C - PER METER LENGTH: PLANAL VERTICAL SINGLE - VPS FRONT VIEW REAR REAR VIEW planal vertical single plus-vph REF. HEAT OUTPUTS TO EN442 = T 60C - PER METER LENGTH: CONCEALED WALL BRACKETS PLANAL VERTICAL SINGLE PLUS - VPH FRONT VIEW REAR REAR VIEW YEAR GUARANTEE: each radiator is individually tested and supplied complete with a 10 year guarantee against and defects caused by faulty materials and manufacture. All radiators are tested to 13 Bars before despatch to guarantee a working pressure of 10 Bars. QUALITY: all radiators are manufactured under BS EN ISO 9000 quality system accepted by BSI. MATERIAL: conform to BS1449, Part 1 and are manufactured from 1.20mm cold rolled steel. INSTALLATION: each radiator is supplied with concealed brackets, 1/2 self jointing air-vents and plugs in the protective heavy duty packaging. For maximum efficiency radiators should be fixed at not outside the measurements given on the drawings herein from finished floor level. Bottom opposite end connections pipe positioning guide for manual valve allow 35mm to centre of pipe. For TRV valve allow 45mm to centre of pipe. To prevent damage to radiator it is strongly recommended during installation to leave protective packaging on radiator by simply removing lug protectors and pre-cut tapping connection. FINISH: each radiator is degreased and finished by being electrostatically powder coated with epoxy polyester stove enamel after an application of water based primer. Thereafter they are oven baked to provide outstanding surface which requires no further painting to a high gloss finish in white enamel (RAL 9016) WATER TREATMENT: on completion of the installation the system should be properly flushed and filled in accordance with the British Standard Code of Practice for the Treatment of Water in Domestic Hot Water Central Heating System BS7593 IMPORTANT Please read the following points carefully before installing your ultraheat radiator: DO make sure that you have a good design and layout of your central heating system as this will ensure satisfactory functioning of the system in general and the radiators in particular. DO vent your system properly. Leaks and corrosion problems are usually due to excess air getting into the system. DO pay attention that the drain points are really at the lowest points in the system. DO make absolutely certain that the system is thoroughly flushed before it is commissioned. Rinse out all metal, flux and other foreign residues, the cause of pin-holing. DO avoid over pumping the system, which causes negative pressure aeration, one of the most common causes of corrosion. DO add an approved chemical inhibitor as an additional safeguard, but remember that it is no substitute for good installation practice. DO observe the above basic rules. Not only will you protect guarantee, but you will have years of trouble-free service from your radiators. - DUE TO POLICY OF CONTINUED IMPROVEMENT IN BOTH DESIGN AND PERFORMANCE OF THE PRODUCTS, THE RIGHT IS RESERVED TO ALTER ANY DETAILS CONTAINED IN THIS BROCHURE WITHOUT NOTIFICATION. - VPH IS SUPPLIED WITH TOP GRILL SIDE PANELS WHERE VPS IS JUST THE PANEL WITH NO TOP GRILL AND SIDE PANELS. -APPROVED AND REGISTERED ACCORDING TO DIN - NF AND ALSO CONFIRM TO ISO AND BS EN ALL ULTRAHEAT RADIATORS ARE MANUFACTURED UN DER A BS EN ISO 9002 : 1994 QUALITY AYATEM APPROVED BY BSI. - ALL PRICES ARE SUBJECT TO VAT. p. 42 (prices shown exclude VAT)