Installation Instructions

Size: px

Start display at page:

Download "Installation Instructions"

Drusilla Day
6 years ago
Views:

1 Installation Instructions KM 6002

2 Safety instructions for installation Installation of the cooktop may only be performed by a qualified technician. The cooktop may only be connected to the oven by a qualified electrician. Install the upper cabinets and ventilation hood before installing the cooktop to avoid damaging the appliance. The veneer or laminate coatings of countertops must be treated with 100 C heat-resistant adhesive which will not dissolve or become deformed. Wall strips must also be heat-resistant. Once the cooktop has been installed, the electrical cord must not be subject to mechanical stress. Make sure that, once the cooktop is installed, it is not possible to touch the underside of the appliance. In some cases, a front cover panel and bottom cover panel may need to be installed (see "Bottom cover panel"). All dimensions are indicated in mm. 27

3 Safety clearances Safety clearance above the cooktop For a ventilation hood positioned above the cooktop, always use the clearance specified by the hood manufacturer. If no specifications are available from the hood manufacturer, or if flammable materials (e.g. wall shelf) are installed above the cooktop, the clearance must be at least 760 mm. If there is more than one appliance installed below the ventilation hood, each with a different safety clearance, the largest clearance must be used. 28

4 Safety clearances Safety clearances to the sides and back of the cooktop Ideally, the cooktop should be installed with plenty of space on either side. There may be a wall at the rear or a tall cabinet or wall on one side (right or left) (see illustrations). Minimum distance between the back of the countertop cut-out and the rear edge of the countertop: 50 mm Minimum distance on the right side between the countertop cut-out and the closest adjacent piece of furniture (e.g. tall cabinet) or a room wall: 50 mm Minimum distance on the left side between the countertop cut-out and the closest adjacent piece of furniture (e.g. tall cabinet) or a room wall: 50 mm Not permitted! Highly recommended! Not recommended! Not recommended! 29

5 Safety clearances Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out and the covering, since high temperatures can damage these materials. If the covering is made of a flammable material (such as wood), the minimum distance between the countertop cut-out and the wall covering must be 50 mm. For coverings made of non-flammable materials (such as metal, natural stone, ceramic tiles) the minimum safety distance between the countertop cut-out and the wall covering is equal to 50 mm minus the thickness of the covering. For example: thickness of wall covering 15 mm 50 mm - 15 mm = minimum distance of 35 mm Flush-mounted cooktops Cooktops with trim or bevelled edges Masonry Wall covering dimension x = thickness of wall covering Countertop Countertop cut-out Minimum distance to flammable materials: 50 mm non-flammable materials: 50 mm - dimension x 30

6 Bottom cover panel Measures must be taken to ensure that it is not possible to touch the underside of the installed cooktop. For this reason, a front cover panel and bottom cover panel must be installed if: The cooktop is wider than the oven installed below it. The cooktop and the oven below it are installed with an offset. The distance from the top edge of the countertop to the bottom cover panel must be at least 55 mm. An air gap of 10 mm must be maintained between the bottom cover panel and the rear wall. 31

7 Instructions for installation Seal between the cooktop and countertop Tiled countertop Do not use sealant between the cooktop and the countertop. Doing so could result in damage to the cooktop or countertop if the cooktop ever needs to be removed for servicing. The sealing strip under the top edge of the appliance provides an adequate seal with the countertop. The grouting and the shaded area under the cooktop frame must be smooth and flat so that the frame will sit evenly on the countertop and so that the sealing strip under the top edge of the appliance can provide an adequate seal with the countertop. 32

8 Installation dimensions Spring clips Installation height Front Space for fastening elements and cable routing 33

9 Installation Preparing the countertop Create the countertop cut-out as shown in the cooktop diagram. Remember to maintain the minimum safety distances (see "Safety clearances"). Wooden countertop Seal any cut surfaces on the wooden countertop with a special varnish, silicone rubber, or resin to prevent the wood from swelling as a result of moisture. The sealant must be temperature resistant. Make sure that the sealant does not get on countertop surface. Position the spring clips on the top edge of the cut-out as shown in the cooktop illustration. Fasten the spring clips using the 3.5 x 25 mm screws supplied with the appliance. The sealing strip ensures that the cooktop will sit securely in the cut-out without slipping. Any gap between the trim and countertop will become smaller over time. 34

10 Installation Natural stone countertops You will need heavy duty double-sided adhesive tape (not included with the cooktop) to fasten the spring clips. Affix the adhesive tape along the top edge of the cut-out in the positions shown in the cooktop illustration. Position the spring clips on the top edge of the cut-out and press them firmly into place. Installing the cooktop Feed the cooktop power cord down through the countertop cut-out. Connect the cooktop to the oven (see "Connection to the oven"). Loosely position the cooktop in the countertop cut-out. Using both hands, press down on the cooktop edges until the cooktop is clearly in place. Make sure that the seal under the cooktop sits flush with the countertop on all sides. This is important to ensure an effective seal. Never seal the cooktop using additional sealant (e.g. silicon). If the seal does not sit flush with the countertop in the corners, the corner radius ( R4) can be carefully cut to fit using a jigsaw. Check that the cooktop works. The cooktop can only be lifted out of the cut-out with a special tool. Apply silicone adhesive to the side edges and bottom edge of the spring clips. 35

11 Connecting the cooktop Insert the plug casing on the cooktop power cord into the plug connector on the oven. Do not force the plug casing into the connector. Connect the EMC ground, which is attached to the bottom casing of the cooktop (depending on the model), to the cable lug on the oven. The plug casing and plug connector are designed so that only one connection alignment is possible. The protective ground wire is integrated in the plug casing. 36

12 Electrical connection Risk of injury. Installation, maintenance and repair work by unqualified persons can cause considerable danger to users, for which Miele is not responsible. Miele cannot be held liable for damage or injury caused by improper installation, maintenance or repair work or by inadequate or faulty grounding in the building's wiring system (e.g. electric shock). The cooktop may only be connected to the oven by a qualified and competent electrician in accordance with current local and national safety regulations. Make sure that all electrical components are shielded and cannot be accessed by users after installation. Connection The voltage, rated load and fuse rating can be found on the oven data plate. Please ensure that these match the building's electrical supply. Disconnecting devices It must be possible to disconnect the appliance from the power supply on all poles using disconnecting devices. When switched off, a contact distance of at least 3 mm must be present. Disconnecting devices include overcurrent protection elements and protective circuit breakers. 37

13 After-sales service, data plate, warranty After-sales service For problems that you cannot resolve on your own, please contact: Your Miele dealer or Miele Service The telephone number for Miele Service can be found at the back of this booklet. When contacting Miele, please have the model and serial number of your cooktop ready. Data plate Affix the extra data plate supplied with the appliance in the box below. Make sure that the model number matches the information on the back of these operating instructions. Warranty For further information, please refer to your warranty booklet. 38

14 39 Canada Importer Miele Limited Headquarters and Miele Centre 161 Four Valley Drive Vaughan, ON L4K 4V8 Customer Care Centre Phone: Germany Manufacturer Miele & Cie. KG Carl-Miele-Straße Gütersloh

15 KM 6002 en-ca M.-Nr / 00

Installation instructions

Installation instructions Ceramic hobs KM 6200 / 6202 / 6203 KM 6204 / 6206 / 6207 / 6208 KM 6212 / 6213 / 6215 / 6216 To avoid the risk of accidents or en-gb damage to the appliance it is essential to