! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.

Size: px

Start display at page:

Download "! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power."

Susan Mills
6 years ago
Views:

1 Electric Wall Oven Technical Information JJW8527DDB/W/Q/S JJW9527DDB/W/S JJW8530DDB/W/Q/S JJW9530DDB/W/S Refer to Service Manual for detailed installation, operating, testing, troubleshooting, and disassembly instructions. Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit.! CAUTION All safety information must be followed as provided in Service Manual This oven contains ESD-sensitive electronics. An ESD discharge may weaken or damage electronic components in the oven. This could cause immediate failure or reduced product life. The following precautions must be taken when working on the oven: Wear an antistatic wrist strap. Connect the free end to a bare metal surface on the oven. Handle all electronic components by their edges only. Do not touch contacts, terminals, or individual components on the printed circuit boards. Touch all anti-static bags to a bare metal surface on the oven before removing parts from their bags. Observe all of these precautions when dealing with old or new electronic components. Models JJW8527DD* JJW8530DD* JJW9527DD* JJW9530DD* Power Source Electrical rating 240 VAC 208 VAC 240 VAC 208 VAC 240 VAC 208 VAC 240 VAC 208 VAC 3.6 Kw 2.7 KW 3.6 Kw 2.7 KW 3.6 Kw 2.7 KW 3.6 Kw 2.7 KW Amperage maximum 15 Amp 13 Amp 15 Amp 13 Amp 15 Amp 13 Amp 15 Amp 13 Amp Frequency 60 Hz 60 Hz 60 Hz 60 Hz Oven 240 V / 208 V Convection N/A N/A N/A N/A 1850 W 1603 W 1850 W 1603 W Bake 2800 W 2100 W 2800 W 2100 W 2800 W 2100 W 2800 W 2100 W Broil 3600 W 2700 W 3600 W 2700 W 3600 W 2700 W 3600 W 2700 W Oven Cutout Dimensions in. (cm) Height 29 1/ / / / Width 25 1/ / / / Depth 24 min min min min Product Exterior Dimensions in. (cm) Height 29 1/ / / / Width 26 3/ / / / Depth 25 7/ / / / Clearance with oven door open 47 7/ / / / Weight lbs. (kg) Approximate shipping weight Unit Features Electronic oven control X X X X Counterbalanced glass oven door X X X X with extra-large viewing window Interior oven light X X X X Automatic oven door latch X X X X Porcelain broiler pan and grid X X X X Heavy duty oven racks with six Two racks Two racks Three racks Three racks positions Multi-Mode convection system N/A N/A X X March

2 Component Testing Procedures Illustration Component Test Procedure Results Oven light socket Test continuity of receptacle terminals.... Indicates continuity with bulb screwed in. Measure voltage at oven light... Bake element Test continuity of terminals... Test voltage to terminals VAC; see wiring diagram for terminal identification. If no voltage is present at oven light check wiring. Approximately 20 Ω - cold. 240 / 208 VAC. Broil element Test continuity of terminals... Test voltage to terminals... Approximately 15 Ω - cold. 240 / 208 VAC. Convection element Test continuity of terminals... Test voltage to terminals... Approximately 30 Ω - cold. 240 / 208 VAC. Convection motor fan Cooling fan motor Verify supply voltage... Check continuity of terminals... Verify supply voltage... Check continuity of terminals VAC 20 Ω high and continuity low. Approximately 400 Ω. Verify terminals are not shorted to chassis. 120 VAC. Continuity. Verify terminals are not shorted to chassis. Temperature sensor Measure resistance... Approximately 1080 Ω at room temperature (70 F). COM NC NO Door lock switch Switch connection in following positions: Unlocked... Locked... COM-NO=Open, COM-NC=Closed. COM-NO=Closed, COM-NC=Open. High limit Verify proper operation... Open at 225 F. Closed at 165 F. C NO Primary Secondary NC Door plunger switch Remove switch from unit and measure the following points: C-NO... Stepdown transformer Verify input voltage... Verify output voltage... Plunger in continuity, Plunger out infinite. Approximately 120 VAC. Approximately 12 VDC. 2 March 2005

3 Component Testing Information Illustration Component Test Procedure Results UH1 Controlled Oven temperature adjustment Press SETUP pad. Press DOWN ARROW to scroll down to TEMP ADJUST. Select oven and enter desired temperature change. Press ENTER pad to accept the change. While increasing or decreasing oven temperature, this does not affect broiling or self-cleaning temperature. The oven offset does not need to be readjusted if there is a power failure. Oven can be adjusted from -35 to +35 by pressing +/- pad. To avoid over adjusting the oven, move temperature 5 degrees each time. Wait 4 seconds for the data entry timer to expire to accept the change. Temperature adjustment will be retained even through a power failure. UH1 Controlled Temperature display Press SETUP pad. Press DOWN ARROW to scroll down to TEMP ADJUST. Select temperature scale C/F, then select SET. Press SETUP pad to exit. UH1 Controlled Clock Display Press SETUP pad. Press CLOCK pad. Press TIME and enter numeric from keypad. Select AM or PM. Press SETUP to end. Press SETUP pad. Press CLOCK pad. Press DAY pad. Press back forward to select day of week. Press SETUP to end. Press SETUP pad. Press CLOCK pad. Scroll down to 12/24 HR. Scroll down to 12/24 HR format. Select SET to activate. Press SETUP pad to exit. Press DOWN ARROW pad to scroll to CLOCK. UH1 Controlled 12 Hour Shutoff Press SETUP pad. Press DOWN ARROW pad to scroll to 12 HOUR SHUTOFF pad. Select ON or OFF. Select SET pad to activate. Press SETUP pad to exit. UH1 Controlled Demo mode Press SETUP pad. Press DOWN ARROW pad to scroll to DEMO pad. Select DEMO to activate. Press SETUP pad to exit. UH1 Controlled Energy Saver Press SETUP pad. Press DOWN ARROW pad to scroll to ENERGY SAVER pad. Select ON or OFF. Select SET pad to activate. Press SETUP pad to exit. UH1 Controlled 208/240 V mode Press SETUP pad. Press DOWN ARROW pad to scroll to 208/240 V pad. Select 208 or 240. Select SET pad to activate. This mode enables the user to indicate F or C on the display. Set clock, day of week, or 12/24 HR clock. Allows the time on the clock to be toggled from 12 hour or 24 hour display. Control will automatically cancel any cooking operation and remove all relay drives 12 hours after the last pad touch. To save energy, the display will turn off after five minutes of no use in time of day mode only. For improved results when using Radiant Bake only, the oven can be set from 240 VAC to 208 VAC. March

4 Component Testing Procedures Illustration Component Test Procedure Results UH1 Controlled Sabbath Mode Press SETUP pad. Press DOWN ARROW pad. Press SABBATH pad to activate Sabbath mode. Select AUTO or MANUAL pad. If AUTO selected, press continue. If MANUAL selected, press ON or OFF. Select SET pad. Auto-Sabbath mode will display a reminder at 2:00 PM on Friday. Manual-Sabbath mode will be instantly programmed for 72 hours. This mode disables the normal 12 hour energy saving mode. The time of day and day of week must be set correctly for this feature to be activated. UH1 Controlled Control Lockout Press and hold BACK and ENTER pads for 5 seconds. To reactivate the control, press and hold BACK and ENTER pads for 5 seconds. Test Mode Follow procedure below to access the Test Mode. This is a safety feature that can be used to prevent accidentally programming the oven. It disables the electronic oven control and locks the cavity door(s). Control lockout features must be reset after a power failure. 1. Press SETUP pad. 2. Press DOWN ARROW pad three times until SERVICE is displayed. 3. Press SERVICE pad. 4. Press and hold BACK and ENTER pads for 5 seconds. 5. Press TEST pad. NOTE: If the oven cavity temperature is greater then 400 F, the Test Mode cannot be activated. NOTE: Once the Test Mode is activated and a function is selected, the control will keep the relay activated until the pad is pressed again. Upon entering TEST Mode all relays are turned off except the DLB relays. All relays are turned off when the TEST Mode is exited. Pad Pressed Beep Version Last Fault DISP Test UBAKE UBROIL UCONV UCOOL UCONV-H UCONV-L UMDL ULITE LBAKE LBROIL LCONV LCOOL LCONV-H LCONV-L LMDL LLITE Relay or Action Activated 1 Second Beep Version of software Display last error code and oven configuration (single, double, convection, nonconvection) Display segments Upper Bake Element Upper Broil Element Upper Convection Element Upper Cooling Fan Upper High Speed Convection Fan Upper Low Speed Convection Fan Upper Motorized Door Lock Upper Oven Light Lower Bake Element Lower Broil Element Lower Convection Element Lower Cooling Fan Lower High Speed Convection Fan Lower Low Speed Convection Fan Lower Motorized Door Lock Lower Oven Light 4 March 2005

5 Component Testing Information Description of Error Codes Error diagnostic codes can only be viewed by entering the Diagnostic Code Display Mode. Each error code is four digits long and is created based on the following table. Digit Description 1 st Primary System: 1 Local to the control circuit board 3 Sensor or meat probe 4 Control input 9 Door lock 2 nd Measurable: d Diagnostic failure: measurable parameter c Control related error, replace control 3 rd Primary failure mechanism 4 th Oven Cavity: 1 Upper oven (or single cavity oven) 2 Lower oven c Control specific Diagnostic Code Checking Code Description When Checked Detection 1c1c Shorted key Always 1 minute 1c2c Keyboard tail disconnected Always 1 minute 1c31 Cancel key circuit problem Always 20 sec 1c32 Cancel key circuit problem Always 20 sec 1c4c Power micro communication failure Always 20 sec 1c5c VCC or ground open circuit Cook or Clean programmed 3 tries 1c6c EEPROM error When accessing EEPROM 3 tries 1c7c Control not calibrated Always 3 tries 1c8c Cook profile corrupted in EEPROM Cook or clean programmed 3 tries 1c81 Cook profile corrupted in EEPROM Cook or clean programmed 3 tries 1c82 Cook profile corrupted in EEPROM Cook or clean programmed 3 tries 1d11 Runaway temperature (650 F), door unlocked Latch unlocked 1 minute 1d12 Runaway temperature (650 F), door unlocked Latch unlocked 1 minute 1d21 Runaway temperature (950 F), door locked Latch locked 1 minute 1d22 Runaway temperature (950 F), door locked Latch locked 1 minute 3d11 Temperature sensor failure (open) Cook or Clean active 20 sec 3d12 Temperature sensor failure (open) Cook or Clean active 20 sec 3d21 Temperature sensor failure (short) Cook or Clean active 20 sec 3d22 Temperature sensor failure (short) Cook or Clean active 20 sec 3d41 Meat probe shorted (upper cavity) Probe cook programmed 20 sec 3d42 Meat probe shorted (lower cavity) Probe cook programmed 20 sec 3d51 Meat probe not calibrated Always 3 sec 4d11 Door switch position failure Clean or Keyboard Lockout active 1 minute 4d12 Door switch position failure Clean or Keyboard Lockout active 1 minute 4d21 No Reverse Airflow Fan rotation (no/low RPM) Cook or Clean programmed 1 minute 4d22 No Reverse Airflow Fan rotation (no/low RPM) Cook or Clean programmed 1 minute 4d31 Reverse Airflow Fan state error (on when supposed to be off) When supposed to be off 1 minute 4d32 Reverse Airflow Fan state error (on when supposed to be off) When supposed to be off 1 minute 4d41 High Reverse Airflow Fan rotation, high RPM Cook or Clean programmed 1 minute 4d42 High Reverse Airflow Fan rotation, high RPM Cook or Clean programmed 1 minute 4d51 Door switch circuit failure Convect, Clean, or Keyboard Lockout programmed 1 minute 4d52 Door switch circuit failure Convect, Clean, or Keyboard Lockout programmed 1 minute 9d11 Latch will not lock 6 Latch should be locked See note 6 9d12 Latch will not lock 6 Latch should be locked See note 6 9d21 Latch will not unlock 6 Latch should be unlocked See note 6 9d22 Latch will not unlock 6 Latch should be unlocked See note 6 9d31 Latch both locked and unlocked (upper cavity) Latch should be locked or when lock attempted See note 6 9d32 Latch both locked and unlocked (lower cavity) Latch should be locked or when lock attempted See note 6 9d41 Latch neither locked or unlocked (upper cavity) Latch should be unlocked or when unlock attempted See note 6 9d42 Latch neither locked or unlocked (lower cavity) Latch should be unlocked or when unlock attempted See note 6 March

6 Component Testing Procedures Diagnostic Code Handling Code Measured Display Action Taken 1c1c Keypress Disable audible for affected key depression, Disable all outputs 1, 2 Disable lights and timers 1c2c Keyboard loop improper value Disable audible for key depression, Disable all outputs 1 Disable lights and timers 1c31 Cancel key improper value mssg 1 (active) / mssg 2 (data) Disable all outputs for cavity 1 1c32 Cancel key improper value mssg 1 (active) / mssg 2 (data) Disable all outputs for cavity 1 1c4c CRC invalid mssg 1 (active) / mssg 2 (data) Disable all outputs 1 1c5c VCC or ground open circuit mssg 1 (active) / mssg 2 (data) Disable all outputs 1 1c6c No response from EEPROM mssg 1 (active) / mssg 2 (data) Disable all outputs 1 1c7c Calibration value out of range mssg 1 (active) / mssg 2 (data) Completely disable oven 4 1c8c CRC invalid mssg 1 (active) / mssg 2 (data) Disable affected oven function 1 1c81 CRC invalid mssg 1 (active) / mssg 2 (data) Disable affected oven function 1 1c82 CRC invalid mssg 1 (active) / mssg 2 (data) Disable affected oven function 1 1d11 Sensor resistance >2237 Ω mssg 1 (active) / mssg 3 (data) Disable all cooking functions for cavity 1d12 Sensor resistance >2237 Ω mssg 1 (active) / mssg 3 (data) Disable all cooking functions for cavity 1d21 Sensor resistance >2787 Ω mssg 1 (active) / mssg 3 (data) Disable all cooking functions for cavity 1d22 Sensor resistance >2787 Ω mssg 1 (active) / mssg 3 (data) Disable all cooking functions for cavity 3d11 Sensor resistance > Infinite Ω mssg 1 (active) / mssg 2 (data) Disable all cooking functions for cavity 3d12 Sensor resistance > Infinite Ω mssg 1 (active) / mssg 2 (data) Disable all cooking functions for cavity 3d21 Sensor resistance < 0 Ω mssg 1 (active) / mssg 2 (data) Disable all cooking functions for cavity 3d22 Sensor resistance < 0 Ω mssg 1 (active) / mssg 2 (data) Disable all cooking functions for cavity 3d41 Probe resistance < 0 Ω mssg 1 (active) / mssg 2 (data) Disable all probe functions 3d42 Probe resistance < 0 Ω mssg 1 (active) / mssg 2 (data) Disable all probe functions 3d51 Calibration value out of range mssg 2 Disable all probe functions 4d11 Door switch not closed when mssg 1 Disable Clean and lockout functions 5 door is locked 4d12 Door switch not closed when mssg 1 Disable Clean and lockout functions 5 door is locked 4d21 Reverse Airflow Fan rotation mssg 1 (active) / mssg 2 (data) Disable all cooking functions for cavity (no/low RPM) 4d22 Reverse Airflow Fan rotation mssg 1 (active) / mssg 2 (data) Disable all cooking functions for cavity (no/low RPM) 4d31 Reverse Airflow Fan rotation No change No action (on when should be off) 4d32 Reverse Airflow Fan rotation No change No action (on when should be off) 4d41 Reverse Airflow Fan rotation mssg 1 (active) / mssg 2 (data) Disable all cooking functions for cavity (high RPM) 4d42 Reverse Airflow Fan rotation mssg 1 (active) / mssg 2 (data) Disable all cooking functions for cavity (high RPM) 4d51 Door switch not open or closed mssg 1 (active) / mssg 2 (data) Disable Convect, Clean, and lockout functions 4, 5 Turn off light and disable light from door switch 4d52 Door switch not open or closed mssg 1 (active) / mssg 2 (data) Disable Convect, Clean, and lockout functions 4, 5 Turn off light and disable light from door switch 9d11 Lock switch not closed mssg 1 (active) / mssg 2 (data) Disable Clean and lockout functions 4 9d12 Lock switch not closed mssg 1 (active) / mssg 2 (data) Disable Clean and lockout functions 4 9d21 Unlock switch not closed mssg 1 (active) / mssg 2 (data) Disable Clean and lockout functions 4 9d22 Unlock switch not closed mssg 1 (active) / mssg 2 (data) Disable Clean and lockout functions 4 9d31 Lock and unlock switches both closed mssg 1 (active) / mssg 2 (data) Disable Clean and lockout functions 4 9d32 Lock and unlock switches both closed mssg 1 (active) / mssg 2 (data) Disable Clean and lockout functions 4 9d41 Neither lock or unlock switches closed mssg 1 (active) / mssg 2 (data) Disable Clean and lockout functions 4 9d42 Neither lock or unlock switches closed mssg 1 (active) / mssg 2 (data) Disable Clean and lockout functions 4 Message 1: Message 2: Message 3: FAULT DETECTED PRESS ENTER TO TRY AGAIN FEATURE NOT AVAILABLE PRESS HELP FAULT DETECTED DISABLE POWER TO CLEAR 6 March 2005

7 Component Testing Information NOTES: 1 "Action Taken" applies as long as the condition exists. If the condition goes away, the control recovers If there is a cook function or timer active, the function continues. The user cannot edit the function, and [Cancel] will cancel the cook mode. Flash rate: 0.2 seconds on, 0.1 second off. Pressing any key will clear the display until the fault clears and is re-triggered. "Action Taken" applies until there is a POR (Power On Reset ["hard reset"]). If the control believes the door is locked, it will attempt to unlock it when the function cancels and the cavity temperature cools. Special conditions for latch faults (9dxx): A known good unlock position is defined as when the unlock switch reads closed and lock switch reads open. A known good lock position is defined as when the unlock switch reads open and lock switch reads closed. A faulted switch means the switch input is reading an invalid state, neither open nor closed. Once a latch fault occurs, latch movement is disabled until there is a POR. An error tone will sound if a function requiring a faulted latch is attempted. If at POR, the latch is not at a known good unlock position: If the latch is at a good lock position, it will attempt to unlock when the RTD (Resistance Temperature Device) temperature is below 400 F. If the latch is not at a good lock position, the control will fault. If a latch fault occurs while the RTD is above the lock temperature, the latch will not try to move, but the fault is still logged to EEPROM after the first stage of detection. The Display column for latch faults applies 1) If the latch was moving when the fault occurred; 2) If the latch is already in a known locked state when the fault occurs. LOCK flashes after a fault is detected and until the unlocked position is achieved. The unlock position may be identified by a successful unlock switch closure, or as the result of timing when the unlock switch is not functioning properly. If the last known good position was unlock (e.g. baking, or idle) and a latch fault occurs, the motor is never moved. The fault is logged to EEPROM and is not seen by the user. The detection for latch faults is in two stages. The first stage is to let the control recover without moving the latch. Then: If the latch was previously at a known good unlock position, the latch will not move and the control will fault. If the control was previously in a known good lock position: If the RTD is below 400 F, the latch will attempt to recover to it s proper position (up to three revolutions). If it cannot, the control will fault and the latch will move to a calculated unlock position. If the RTD is at or above 400 F, the control will fault. When the RTD cools to below 400 F, the control will attempt to recover to a good unlock position (up to three revolution). If it cannot, the control will fault and the latch will move to a calculated unlock position. Note: If the unlock position cannot be found, this may result in a second fault, the first fault occurring when the latch request was locked, and the second when the latch request is unlocked. If the latch is moving when the fault occurs, the control will bypass the first stage of detection and immediately try to find it s proper position. If it cannot, the control will fault and the latch will move to a calculated unlock position. Affected DLBs (Double Line Breaks) and loads are disabled during detection. If the control is in a known good unlock position and the lock switch becomes faulted: The control will not fault. If a function requiring latch movement is attempted while the lock switch is faulted, the control will sound an error tone and the function will be disabled. If the control is in a known good lock position and the unlock switch becomes faulted: The control will not fault. After the function is canceled and unlock is attempted, the control will attempt to unlock the latch according to the procedures in these notes. March

8 Wiring Diagram and Schematic Wiring Diagram 8 March 2005

9 Wiring Diagram and Schematic Control Circuits March

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires it.

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires it. Electric Wall Oven Technical Information JJW8627DD*, JJW8630DD*, JJW9627DD*, JJW9630DD*, JJW9827DD*, JJW9830DD* Refer to Service Manual 16022506 for detailed installation, operating, testing, troubleshooting,