Installation & Operation Instructions Nr _EN_Manual

Size: px
Start display at page:

Download "Installation & Operation Instructions Nr _EN_Manual"

Transcription

1 Installation & Operation Instructions Nr _EN_Manual Product: Fog / Jet Monitor (FJM) Manual and Manual with Foam Inductor Versions Model Types: FJM-80, FJM-100, FJM-150 FJM-80S, FJM-100S, FJM-150S pagina 1 van 27 / page 1 of 27

2 SECTION CONTENTS 1. GENERAL 1.1 Manual 1.2 Liability Warning 1.3 Warranty 2. INSTALLATION 2.1 Safety 2.2 Inspection 2.3 Installation 2.4 Commissioning 3. OPERATION 3.1 System activation 3.2 System deactivation 3.3 Suction hose and foam storage 3.4 After use 4. MAINTENANCE AND INSPECTION 4.1 Maintenance 4.2 Inspection 5. TROUBLESHOOTING 6. SPARE PARTS 7. CHANGING O-RINGS 7.1 Changing the o-rings within the horizontal bearing 7.2 Changing the o-rings within the vertical bearing 7.3 Changing the o-rings within the FJM and FJM-S outlet nozzle 8. TECHNICAL DATA 8.1 Paint specification/procedure 8.2 Test criteria 9. DECLARATION OF CONFORMITY 10. ORDERING INFORMATION 11. WORKS CERTIFICATE 12. COMMISSIONING CHECKLIST pagina 2 van 27 / page 2 of 27

3 WARNING! Do not direct the flow beam towards any person 1. GENERAL 1.1. Manual This manual describes the installation, operation and maintenance of a manual (FJM) and manual with built in foam concentrate inductor (FJM-S) series fire suppression monitor Liability Warning FJM series monitors must be operated and maintained in compliance with this document as well as with applicable standards, in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the proper operation or integrity of this device. The owner is responsible for maintaining his fire protection unit or system and devices in proper operating conditions. The manufacturer or reseller should be contacted regarding any questions. This manual must be read and understood by all personnel involved in erection, operation and maintenance of this product and shall be kept in an accessible place for review. Operation of this device without a full understanding and comprehension of the manual could be dangerous. The unit should not under any circumstance be operated outside the water, angle, or pressure range as indicated in this manual. The monitor should also not be installed or operated with the nozzle washer disc in the fully closed position. The water supply to the monitor must be increased and decreased smoothly (and must never exceed the maximum operating pressure of 16bar) in order to avoid the water hammer effect from a sudden momentum change in the fluid Warranty The seller warrants for a period of one year from date of shipment (warranty period) that products furnished hereunder will be free from defects in material and workmanship. This warranty is invalid if the device is, or has been, misused or neglected or if there have been accidents to the equipment or if it has been altered or modified in any way. pagina 3 van 27 / page 3 of 27

4 2. INSTALLATION 2.1. Safety The installation is not complicated but must be carried out by qualified personnel. The directions given in this manual must be followed. Make sure that the monitor and its components are safely secured when installing the monitor. Use only lifting gear and equipment that are fit for purpose Inspection Inspect the monitor and any additional equipment for damage or other deviations that might have occurred during transport. Check marking and identification labels on the equipment against material specification / order confirmation Installation Important: Ensure the monitor is located in the system in such a way as to minimise the potential effect of a water hammer. The monitor is intended for connection to a vertical riser pipe flange. Check that the riser pipe flange is of the corresponding type to what is specified for the monitor or the monitor stand pipe [Refer to figure 1 and table 1]. Three monitor flange ratings are available: DIN2533 PN 16 ANSI B lbs JIS 10K. All three flanges are raised face type with smooth finish. The gasket between the standpipe and the monitor can be of any suitable standard type provided that it is compatible with the foam agent being used. The gasket material must be verified against the foam concentrate datasheet. Nuts and bolts for the stand pipe flange must be of suitable type depending of the installation. For FJM-80 and FJM-100: use studs to DIN 939 M16x60, short end screwed into the monitor. For FJM-150: use studs to DIN 939 M20x70, short end screwed into the monitor. Ensure that the nuts are tightened to the correct torque as defined by the type of installation, standard and authority having jurisdiction. Check the monitor movements are smooth and that the locking device works. Ensure that the nozzle washer disc has been set correctly according to the required flow and pressure. See turns of disc datasheet [Refer to figures 2 to 7 and section 3]. pagina 4 van 27 / page 4 of 27

5 Figure 1 - Mounting flange details. Table 1: Mounting Flange Details Monitor Version / Dimension FJM-80 & FJM-80S DIN/ANSI FJM-80 DIN/JIS FJM-80S DIN/JIS FJM-100 & FJM-100S DIN/ANSI FJM-100 DIN/JIS FJM-150 & FJM-150S DIN/ANSI/JIS A 190 mm 185 mm 220 mm 220 mm 210 mm 285 mm B 24 mm 24 mm 24 mm 24 mm 24 mm 26 mm C M16 M16 M16 M16 M16 M20 D (ANSI/JIS) Ø 152 mm Ø 150 mm Ø 175 mm Ø 190 mm Ø 175 mm -- E (DIN) Ø 160 mm Ø 160 mm Ø 180 mm Ø 180 mm Ø 180 mm -- F Ø 244 mm pagina 5 van 27 / page 5 of 27

6 Figure 2 - FJM-80 manual monitor turns of disc FJM -80 CAPACITY AT OPENING TURNS OF DISC FROM CLOSED POSITION AT MONITOR INLET PRESSURE Figure 3 - FJM-80S manual monitor with built-in foam concentrate inductor turns of disc FJM-80 S CAPACITY AT OPENING TURNS OF DISC FROM CLOSED POSITIONAT MONITOR INLET PRESSURE pagina 6 van 27 / page 6 of 27

7 Figure 4 - FJM-100 manual monitor turns of disc FJM-100 CAPACITY AT OPENING TURNS OF DISC FROM CLOSED POSITION AT MONITOR INLET PRESSURE Figure 5 - FJM-100S manual monitor with built-in foam concentrate inductor turns of disc FJM-100 S CAPACITY AT TURNS OF DISC AT MONITOR INLET PRESSURE 99/05 FJM-100 S 1011/102 (Power water and suction capacity included) pagina 7 van 27 / page 7 of 27

8 Figure 6 - FJM-150 manual monitor turns of disc FJM-150 CAPACITY AT OPENING TURNS OF DISC FROM CLOSED POSITION AT MONITOR INLET PRESSURE Figure 7 - FJM-150S manual monitor with built-in foam concentrate inductor turns of disc datasheet. FJM-150 S CAPACITY AT OPENING TURNS OF DISC FROM CLOSED POSITION AT MONITOR INLET PRESSURE (Power water and suction capacity included) pagina 8 van 27 / page 8 of 27

9 CAUTION! Before starting the monitor please read section 3 which details the operation of the monitor Commissioning Check that all the bolts and screws which have been adjusted or relocated are firmly fixed - follow instructions given in this section. Check marking and identification labels on the equipment against material specification / order confirmation to ensure that the water capacity, pressure rating and flange are correct. Check that the operating sectors settings correspond to the protected areas. Run the system according to instructions given in section 3. Make adjustments to the settings if required. After any adjustments, a new functional test (with or without water) is recommended. After commissioning, flush the monitor by running the system with water if foam concentrates have been used. 3. OPERATION The FJM series monitors are designed for easy handling and operation, especially during operation at the maximum working pressure, due to the inclusion of the patented water balanced slide bearings. The FJM-S series monitors have a built-in inductor, meaning that foam concentrate can be induced directly from a can or a tank via hose/pipe into the monitor nozzle. The foam concentrate induction and the water capacity are factory calibrated (see the specific order specification for the capacity data). When running with water only, the water capacity can also be adjusted on-site to obtain the desired value and is constant, irrespective of jet or fog position. When running with foam however, the nozzle capacity must be adjusted to the capacity value of the built-in inductor (specified in the monitor material specification), or the amount of foam liquid produced could be significantly reduced or increased. The nozzle capacity setting is changed by undoing the nut (FJM series monitors) or the nozzle (FJM-S series monitors) in the centre of the nozzle washer disc and turning the nozzle washer disc clockwise until it reaches the stop. This is the closed position or zero position, see figure 8. From the zero position turn the nozzle washer disc anti-clockwise to the desired position according to the relevant turns of disc data sheet (as detailed in figures 2 to 7) before tightening the nut or nozzle in the centre of the nozzle washer disc. In addition to the graph on each turns of disc data sheet, there is a K-factor equation which can be used to calculate the required number of nozzle washer disc turns to correctly set the nozzle capacity. The equation is: K-factor = Q / P Where: Q = flow rate (litres/minute) P = inlet pressure (bar) Q For example, with an inlet pressure of 8 bar and a required flow rate of 2400 litres/minute, the K-factor of the system would be: K-factor = 2400 / 8 = 848,5 Therefore looking at table on the turns of disc datasheets, the required setting to use is just under 5 turns for an FJM-80, just over 4 turns for an FJM-100, and that the system is not suitable for either an FJM-150 or FJM- 150S monitor. A nozzle washer key is available from the seller which fits into the two holes on the nozzle washer disc to aid its turning and set-up. The order part number is , and it is shown in figure 8 below. The nozzle washer nut (FJM series) or nozzle (FJM-S series) must be held as the nozzle washer is turned to the correct torque. pagina 9 van 27 / page 9 of 27

10 Figure 8 - Setting the nozzle capacity using turns of disc from the closed zero position. WARNING! Never leave the nozzle washer disc in the closed zero position. Figure 9 - Nozzle washer key (Part No ) available for setting the nozzle capacity. pagina 10 van 27 / page 10 of 27

11 3.1. System activation Activate the control system for the monitor if it is not already activated. Orient the outlet pipe of the monitor in such a direction that the water jet cannot cause injuries or damage. Be aware that the power of the jet is extremely dangerous. Activate the water supply to the monitor by smoothly opening the control valve or starting the pump. Operate the monitor manually left and right using the handles on the side of the monitor as well as up and down using the handle on top of the outlet part. Operate the fog and jet function by moving the outlet nozzle in and out using the handle on the side of the nozzle. The monitor water jet should be aimed at the base of the fire or in front of it, while for cooling purposes the jet should be directed onto the point or surface to be cooled. If the monitor is required to operate whilst unattended, lock it in desired vertical position. A locking device is not required to prevent horizontal rotation as the monitor is designed to provide a balanced reaction force System deactivation Shut-off the water supply. Orient the monitor into a desired re-start position, depending of safety aspects and protection priority areas to be covered. In sub-zero temperatures, the monitor outlet nozzle should be directed downwards in order to drain the outlet nozzle and avoid freezing. The stand pipe should also be drained. Deactivate the monitor control system if that is included in the local procedures. Leave the monitor in a ready-to-operate status. Report any wear or observed deviations from normal operation Suction hose and foam storage The suction hose for all FJM-S series monitors shall be purchased as an optional part. The suction hose can be supplied with a stop valve to enable the foam line to be closed, leaving only the water line open, which will allow the foam concentrate to be cleaned out after use or allow functional testing without using up foam concentrate. When using an FJM-S, the atmospheric tank must be fitted with a breathing valve in order to avoid positive or negative pressure building up within the tank which will result in the foam aspiration stopping, and/or cause potential damage to the tank. Dimensions and lengths are critical for the function of the FJM-S series monitors. Foam storage installation is also critical as the suction function has limitations. Adjustable proportioning for FJM-S series monitors is also available via a suction hose with built-in metering valve. A scale plate indicates the position at which the valve should be set in order to obtain the required induction rate (0% to 6% range only). The suction hose must be same size or larger than the following: FJM-80S: 1 ¼ suction hose (1 ¼ BSP male connection required) FJM-100S and FJM-150S: 2 suction hose (2 BSP male connection required) [See section 8 for connection location on the FJM-S monitor] The maximum hose length is 3 meters (excluding pick-up syphon tube). Note: Although all types of foam concentrate are suitable for the monitor, the required foam concentration (as a percentage, %) must be specified at the point of order. pagina 11 van 27 / page 11 of 27

12 Figure 10-3 metre suction hose for the FJM-80S (Part No with stop valve) (Part No without stop valve) Figure 11-3 metre suction hose for the FJM-100S and FJM-150S (Part No ) Figure 12-3 metre adjustable proportioning suction hose (Part No : FJM-80S) (Part No : FJM-100S) 3.4. After use After use, flush the monitor by running the system with water if foam concentrate has been used, then drain the monitor. Also flush the suction hose, ensuring that it is clean and that all residue and deposits have been removed. Make sure the monitor is ready to be used when it is left after service, maintenance, inspection or fire drill. This will ensure that the monitor will operate properly the next time it is required. pagina 12 van 27 / page 12 of 27

13 4. MAINTENANCE AND INSPECTION 4.1. Maintenance To ensure full functionality, the monitor should be operated on a regular basis; at least once a month is recommended. It is also recommended to run the monitor with water during these monthly functional tests. O-rings in the moving parts, (fog/jet outlet nozzle, elevation and horizontal movement), must be lubricated at least once a year. Apply waterproof grease to the inside the fog/jet brass outlet nozzle and lubricate the elevation and horizontal bearings by spraying grease into the bearing. The fog/jet outlet nozzle and elevation and horizontal movement o-rings need to be checked every two years for damage and wear. When changing o-rings, make sure to thoroughly grease them as well as the o-ring grooves. Figure 13 - Lubrication points on the FJM and FJM-S series monitors. Apply grease to the inside top and bottom areas of the brass outlet nozzle. Spray elevation bearings between the pipe and the bearing ring. Spray horizontal bearing in the gap between the upright and the flange. In order to protect the monitor from the effects of wind, rain and snow it is recommended that it is covered when not in use. Covers are available for the FJM-100 and FJM-100S monitors, (part number ), as well as the FJM-150 and FJM-150S monitors, (part number ). A snow and dust nozzle cap is available for the FJM-80, FJM-80S, FJM-100 and FJM-100S monitors, which can be tied to the flange so that during operation the cap will be retained after being forced off the top of the nozzle by the force of the jet or spray. Figure 14 - Monitor cover. Figure 15 - Monitor snow/dust nozzle cap. pagina 13 van 27 / page 13 of 27

14 4.2. Inspection Inspection of the monitor is recommended to be carried out monthly. Visually inspect the monitor for any damage or unauthorised adjustments etc. Check that there is no obstruction in the water way between the outlet nozzle and the nozzle washer disc. Make sure to count the turns of disc settings before removing parts from the water way and make sure it is returned to the right settings after re-assembling the parts. 5. TROUBLESHOOTING The monitor is designed to meet the highest levels of reliability. If these operation and maintenance instructions are followed, malfunction or performance loss should not be expected. If the monitor fails to function as expected, check the trouble shooting guide below before consulting your dealer. Problem Leakage from the elevation or horizontal bearing is observed. Poor fog and jet performance. Monitor is difficult to move horizontally. Foam concentrate is not induced into the monitor. (FJM-S series monitor only) Solution Check o-rings and replace if necessary. [Refer to section 7] 1. Check nozzle washer turns of disc setting is correct. 2. Check the water pump is working properly. 3. Ensure the area between the nozzle washer disc and the diffuser is clear of debris and blockages. De-activate the system and remove the monitor from service. Remove the flange bolts and clean the mating flange surfaces before applying grease. 1. Ensure there are no air leakages in the foam line. 2. Check valve is open. 3. Check the foam concentrate container is not empty. 4. Ensure the suction hose is the correct size and length. [Refer to section 3.3] 5. Check nozzle washer turns of disc setting is correct. 6. SPARE PARTS The following spare part recommendations are made in respect to the effect of wear or ageing on the expected lifetime of this monitor. It is recommended that the end user keeps two years operational spares in stock. Please refer to figure 16 for the location of each spare part. pagina 14 van 27 / page 14 of 27

15 Figure 16 - Spare parts identification for the monitor. Table 2: Manual Monitor Spare Parts List Item No. Description FJM-80 Part Number FJM-100 Part Number FJM-150 Part Number 1 Plastic Handle Lock Screw Ball / Knob Bushing Locking Screw O-Ring Kit Dome Nut pagina 15 van 27 / page 15 of 27

16 Table 3: Manual Monitor with Built-In Foam Concentrate Inductor Spare Parts List Item No. Description FJM-80S Part Number FJM-100S Part Number FJM-150S Part Number 1 Plastic Handle Lock Screw Ball / Knob Bushing Locking Screw O-Ring Kit Nozzle (specific to order) (specific to order) (specific to order) 9 Suction Hose Dome Nut Note: Each o-ring kit includes: Replacement o-rings Instructions for changing horizontal bearing o-rings Instructions for changing elevation bearing o-rings Instructions for changing outlet nozzle o-rings Replacement identification label 100ml tube of grease 7. CHANGING O-RINGS The system must be de-activated and the monitor removed from service before any work begins. It is also advisable to place the monitor onto a work bench or similar in order to aid the process Changing the o-rings within the horizontal bearing Figure 17 - Identification of parts used when changing the horizontal bearing o-rings. Loosen and remove all the screws (1) from under the flange. Remove the three o-rings (2, 3 and 5) and visually inspect the surfaces inside the hydro balanced bearing for any wear or damage. Make sure that all four holes (4) on the bearing ring are free from dirt and other contaminants, clean if necessary with a drill or a round file with a diameter of 3mm. Clean all the surfaces and all the o-ring grooves within the bearing to ensure that any dirt or water is removed. Grease the o-ring grooves and the o-rings with silicone grease. pagina 16 van 27 / page 16 of 27

17 Grease the surface of the flange mating the bearing ring with a generous amount of water resistant grease. Carefully assemble the joint by first re-inserting the o-ring at position (3) followed by the o-ring at position (2). Ensure that both o-rings are kept in position during the assembly. Re-insert the o-ring at position (5) and assemble the flange onto the bearing ring and insert the screws (1), tighten the screws in an intertwined sequence to correct tightening torque according to strength class 8.8. Remove all excess grease by using a cloth or rag, do NOT use solvent Changing the o-rings within the vertical bearing Figure 18 - Identification of parts used when changing the vertical bearing o-rings. Remove both handle nuts (4) and pull out the bar which is then revealed. Loosen and remove all the screws (1) that hold the plate onto the bearing ring and remove the plate. Whilst supporting the outlet part (5), as it will drop from its position, move both bearing rings (2) to the side and safely remove the outlet part. Remove both of the bearing rings (2) from the unit and then remove the o-rings (3). Clean all the surfaces and all the o-ring grooves within each bearing ring (2) to ensure that any dirt or water is removed. Grease the o-ring grooves and the o-rings with silicone grease, grease the pipe ends as well. Insert the new o-rings into the bearing rings. Assemble the bearing rings and the outlet nozzle in reverse order, ensure that both o-rings are kept in position, fasten the plate and tighten the screws. Remove the o-ring and clean the o-ring groove in each of the handle nuts (4), apply grease and change the o-rings. Assemble the bar and both handle nuts. Remove all excess silicone grease by using a cloth or rag, do NOT use solvent. Both handle nuts (4) must be tightened with correct torque. Too high a torque will restrict the outlet part which in turn impacts the vertical movement. Too low a torque and the monitor will leak. Therefore, move the outlet part (5) up and down by hand and tighten the nuts until the pipe end makes contact, then open the nut ¼ of a turn. Operate the monitor as normal and check for any leakage, if no leaks are observed conduct a functionality test. pagina 17 van 27 / page 17 of 27

18 7.3. Changing the o-rings within the FJM and FJM-S outlet nozzle Figure 19 - Identification of parts used when changing the outlet nozzle o-rings. Remove the dome nut (4) and washer disc nut (3) [FJM] or the nozzle (1) [FJM-S]. Screw the nozzle washer disc (5) to the bottom position and count the turns (also parts of turns) required. Make a note of this. Unscrew and remove the nozzle washer disc. Remove the locking screw (8) and bushing (7). Take out the outlet nozzle (2). Change the o-ring (6) and lubricate with silicon grease. Lubricate the internal surface of the outlet nozzle (2) with silicon grease. Re-assemble the outlet nozzle. Re-assemble the bushing (7) and the locking screw (8). Re-assemble the nozzle washer disc and screw it to bottom and then up to the position recorded previously. Lock the nozzle washer disc with the washer disc nut (3) and dome nut (4) [FJM] or the nozzle (1) [FJM-S]. Check the movement of the outlet nozzle by moving it backwards and forwards a few times. pagina 18 van 27 / page 18 of 27

19 8. TECHNICAL DATA Table 4: FJM and FJM-S Monitor Performance Data FJM-80 FJM-80S FJM-100 FJM-100S FJM-150 FJM-150S Maximum Water 3,700 l/min 3,700 l/min 6,000 l/min 6,000 l/min 11,700 l/min 11,700 l/min Capacity Foam Suction n/a 170 l/min n/a 320 l/min n/a 600 l/min Capacity Test Pressure ( bar 24 bar 24 bar 24 bar 24 bar 24bar x Max. Pressure) Maximum 16 bar 16 bar 16 bar 16 bar 16 bar 16 bar Working Pressure Optimum Working 12 bar 12 bar 12 bar 12 bar 12 bar 12 bar Pressure * Minimum Inlet 4 bar 4 bar 4 bar 4 bar 4 bar 4 bar Pressure Rotation Elevation -60 / / / / / / +70 Suction n/a 1-1/4 BSP n/a 2 BSP Male n/a 2 BSP Male Connection Male Approximate Weight 14 kg (31 lbs) 15 kg (33 lbs) 22 kg (49 lbs) 24 kg (53 lbs) 57 kg (126 lbs) 60 kg (132 lbs) * The optimum work ing pressure occurs when the max imum throw length is reached. Figure 20 - Dimensions of the FJM-80, FJM80-S, FJM-100 and FJM-100S monitors. pagina 19 van 27 / page 19 of 27

20 Table 5: Dimensions of the FJM-80, FJM80-S, FJM-100 and FJM-100S monitors Dimension / Monitor Version FJM-80 DIN/ANSI FJM-80 DIN/JIS FJM-80S DIN/ANSI FJM-80S DIN/JIS FJM-100 DIN/ANSI FJM-100 DIN/JIS FJM-100S DIN/ANSI FJM-100S DIN/JIS A B C D E Flange Type 455 mm ~ 150 mm ~ 295 mm ~ 300 mm n/a 80 DIN PN 16 or 3 ANSI 150 lbs 455 mm ~ 150 mm ~ 295 mm ~ 300 mm n/a 80 DIN PN 16 or 80 JIS B K 455 mm ~ 150 mm ~ 300 mm ~ 350 mm 1-1/4 BSP Male 80 DIN PN 16 or 3 ANSI 150 lbs 455 mm ~ 150 mm ~ 300 mm ~ 350 mm 1-1/4 BSP Male 80 DIN PN 16 or 80 JIS B K 520 mm ~ 170 mm ~ 335 mm ~ 370 mm n/a 100 DIN PN 16 or 4 ANSI 150 lbs 520 mm ~ 170 mm ~ 335 mm ~ 370 mm n/a 100 DIN PN 16 or 100 JIS B K 520 mm ~ 170 mm ~ 335 mm ~ 425 mm 2 BSP 100 DIN PN 16 or Male 4 ANSI 150 lbs 520 mm ~ 170 mm ~ 335 mm ~ 425 mm 2 BSP Male 100 DIN PN 16 or 100 JIS B K Figure 21 - Dimensions of the FJM-150 and FJM-150S monitors. Table 6: Dimensions of the FJM-150 and FJM-150S monitors Dimension / Monitor Version FJM-150 DIN/JIS/ANSI FJM-150S DIN/JIS/ANSI A B C D E Flange Type 930 mm 222 mm 510 mm 540 mm n/a 150 DIN PN 16 or 6 ANSI 150 lbs or150 JIS B K 930 mm 222 mm 510 mm 630 mm 2 BSP Male 150 DIN PN 16 or 6 ANSI 150 lbs or 150 JIS B K pagina 20 van 27 / page 20 of 27

21 Figure 22 - FJM monitor length-height relationship graph and average fog pattern (in still air). The reaction force resulting from use of the FJM monitor can be calculated using the following equation: K-factor = Q / P Where: Q = flow rate (litres/minute) P = inlet pressure (bar) Q pagina 21 van 27 / page 21 of 27

22 pagina 22 van 27 / page 22 of 27

23 8.1. Paint specification/procedure Degrease using standard cellulose thinners. Degrease using the Di-aqua water base solution. Degrease using a spirit wipe or similar product. Apply one even coat of single pack primer to a DFT 25 microns. Cure in the oven. Wash down using spirit wipe Apply one coat of two pack paint for an even solid coating to a DFT 50 microns. Cure in the oven Test criteria The monitors are hydrostatically tested for a minimum period of 10 minutes at a pressure of 24bar. The manual with built in foam concentrate inductor (FJM-S) series monitors are tested with water/water, instead of water/foam concentrate, and the pass range for foam induction is detailed in table 7 below. As can be seen, the pass range meets the minimum requirements of EN Table 7: Pass Range for the FJM-S Series Monitors (Foam Induction) Nominal Foam Induction SKUM Water/Water Pass Range EN Pass Range 1 % 1.1% to 1.3% 1% to 1.3% 2 % 2.2% to 2.6% 2% to 2.6% 3 % 3.3% to 3.9% 3% to 3.9% 4 % 4.4% to 5.0% 4% to 5% 5 % 5.5% to 6.0% 5% to 6% 6 % 6.6% to 7.0% 6% to 7% 9. DECLARATION OF CONFORMITY Due to the fact that these monitors are intended for use with water and are not classed as machines it therefore falls under article 3, paragraph 3 of directive 97/23/EC meaning that it cannot be CE marked. These monitors are designed and manufactured in accordance with the sound engineering practice of a Member State in order to ensure safe use. pagina 23 van 27 / page 23 of 27

24 10. ORDERING INFORMATION At the point of order please specify the following information: 1. Part Number (see table 8 below). 2. Monitor Type (manual or manual with built-in foam concentrate inductor). 3. Flange Type (DIN, ANSI or JIS). When ordering an FJM-S monitor please specify additional information: 4. Capacity Required (l/min). 5. Inlet Pressure (bar). 6. Foam Concentrate (%). Material certificates are chargeable and will be available following the supply of the monitor(s) if required. For third party inspection (TPI) please refer to your local sales representative for charges and available agencies. Table 8: FJM and FJM-S Monitor and Accessory Part Numbers Monitor/Accessory Description Part Number FJM-80 DIN/ANSI FJM-80 DIN/JIS FJM-80S DIN/ANSI (excluding suction hose) FJM-80S DIN/JIS (excluding suction hose) FJM-80S suction hose (1-1/4 3metre length without stop valve) FJM-80S suction hose (1-1/4 3metre length with stop valve) FJM-80S adjustable proportioning suction hose (1-1/4 3metre length) FJM-80 and FJM-80S snow/dust nozzle cap Please contact sales office FJM-100 DIN/ANSI FJM-100 DIN/JIS FJM-100S DIN/ANSI (excluding suction hose) FJM-100S suction hose (2 3metre length) FJM-100S adjustable proportioning suction hose (2 3metre length) FJM-100 and FJM-100S weather cover FJM-100 and FJM-100S snow/dust nozzle cap Please contact sales office FJM-150 DIN/ANSI/JIS FJM-150S DIN/ANSI/JIS (excluding suction hose) FJM-150S suction hose (2 3metre length) FJM-150 and FJM-150S weather cover FJM nozzle washer key pagina 24 van 27 / page 24 of 27

25 11. WORKS CERTIFICATE pagina 25 van 27 / page 25 of 27

26 12. COMMISSIONING CHECKLIST pagina 26 van 27 / page 26 of 27

WATER POWERED OSCILLATING MONITOR

WATER POWERED OSCILLATING MONITOR WATER POWERED OSCILLATING MONITOR HD FIRE PROTECT TECHNICAL DATA MODEL VAJRA 331-S FLOW With 40U 500 or 750 or 1000 GPM. MINIMUM & MAXIMUM OPRATING PRESSURE FACTORY HYDROTESTED SWIVEL JOINT With HF40U

More information

TECHNICAL DATA. Wet 26a. February 22, 2009

TECHNICAL DATA. Wet 26a. February 22, 2009 February 22, 2009 Wet 26a 1. DESCRIPTION The Viking Alarm Check Valve serves as a check valve by trapping pressurized water above the clapper and preventing reverse flow from sprinkler piping. The valve

More information

Parenzo Range. Basin Mixer, Bath Filler & Bath Shower Mixer. Assembly instructions

Parenzo Range. Basin Mixer, Bath Filler & Bath Shower Mixer. Assembly instructions Parenzo Range Basin Mixer, Bath Filler & Bath Shower Mixer Assembly instructions We have designed these products with your enjoyment in mind. To ensure that they work to their full potential, they need

More information

Model: 1413 Model: 1418 Float-Controlled Condensate Trap, PN 100

Model: 1413 Model: 1418 Float-Controlled Condensate Trap, PN 100 1 Safety instructions Model: 1413 Model: 1418 Float-Controlled Condensate Trap, PN 100 1.1 Proper use Any improper use, intervention in the design and deviation from the design data automatically lead

More information

541D19 SERIES. Technical Manual. A Division of Aquion Partners L.P.

541D19 SERIES. Technical Manual. A Division of Aquion Partners L.P. 541D19 SERIES Technical Manual A Division of Aquion Partners L.P. Table of Contents Introduction... Page 1 Technical Specifications... Page 2 Flow Diagrams... Page 3 Injector & Flow Control Selection Injector...

More information

Operation Manual R205BV, R209BV

Operation Manual R205BV, R209BV Operation Manual R205BV, R209BV 1 Safety Instruction The rotary evaporator is manufactured according to current methods and accepted safety regulations. However, risks still exist during the installation,

More information

Inta City Shower Mixing Valve CT20010CP

Inta City Shower Mixing Valve CT20010CP Inta City Shower Mixing Valve CT20010CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept any responsibility

More information

Deluge Shower Mixing Valve 10045CP

Deluge Shower Mixing Valve 10045CP Deluge Shower Mixing Valve 10045CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept any responsibility

More information

Puro Mini Dual Control Shower Mixer PU90010CP

Puro Mini Dual Control Shower Mixer PU90010CP Puro Mini Dual Control Shower Mixer PU90010CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept

More information

TITAN FLOW CONTROL, INC.

TITAN FLOW CONTROL, INC. PREFACE: TITAN FLOW This manual contains information concerning the installation, operation, and maintenance of Titan Flow Control (Titan FCI) Suction Diffusers. To ensure efficient and safe operation

More information

Operating Manual. Model: 1400 Model: 1400-N RIFOmat Float-Controlled Condensate Traps, PN Safety instructions. 2 General description and use

Operating Manual. Model: 1400 Model: 1400-N RIFOmat Float-Controlled Condensate Traps, PN Safety instructions. 2 General description and use 1 Safety instructions 1.1 Proper use Model: 1400 Model: 1400-N RIFOmat Float-Controlled Condensate Traps, PN 100 Any improper use, intervention in the design and deviation from the design data automatically

More information

OPERATING MANUAL UG2000D SERIES SPRAY GUN CLEANERS UG2000D, UG2000DM UNI-RAM CORPORATION ONTARIO CANADA UG2000DM UG2000D REVISION

OPERATING MANUAL UG2000D SERIES SPRAY GUN CLEANERS UG2000D, UG2000DM UNI-RAM CORPORATION ONTARIO CANADA UG2000DM UG2000D REVISION OPERATING MANUAL UG2000D SERIES SPRAY GUN CLEANERS UG2000D, UG2000DM UG2000D UG2000DM UNI-RAM CORPORATION ONTARIO CANADA REVISION 2015-08 INTRODUCTION Uni-ram holds many patents on designs used in its

More information

BlueHeat AirTop 2000 Heater

BlueHeat AirTop 2000 Heater BlueHeat AirTop 000 Heater Air Heater Installation Manual Ford E-Series 6.0L Diesel Beginning Model Year: 006 Special instructions for these models Part locations may differ slightly dependent on the vehicle

More information

USER MANUAL SPRAY GUN CLEANER - WATER BASED PAINTS UA400W CAUTION FOR WATER BORNE PAINTS ONLY

USER MANUAL SPRAY GUN CLEANER - WATER BASED PAINTS UA400W CAUTION FOR WATER BORNE PAINTS ONLY USER MANUAL SPRAY GUN CLEANER - WATER BASED PAINTS UA400W CAUTION FOR WATER BORNE PAINTS ONLY THIS UNIT IS NOT DESIGNED FOR USE WITH SOLVENT BASED PAINT UNI-RAM CORPORATION ONTARIO CANADA REV 2010-09 CONTENTS

More information

UPP7500E2 AUTOMATIC PRESSURE POT CLEANER

UPP7500E2 AUTOMATIC PRESSURE POT CLEANER USER MANUAL UPP7500E2 AUTOMATIC PRESSURE POT CLEANER UNI-RAM CORPORATION ONTARIO CANADA REV 2012-12 INTRODUCTION Uni-ram holds many patents on designs used in its innovative products. Every machine is

More information

Mio Concealed Shower Mixing Valve MI40010CP

Mio Concealed Shower Mixing Valve MI40010CP Mio Concealed Shower Mixing Valve MI40010CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept any

More information

SSS Intrepid 16 FMS. Manual

SSS Intrepid 16 FMS. Manual SSS Intrepid 16 FMS Manual The contents of this manual are based on the latest product information available at the time of publication. Triple S reserves the right to make changes or improvements to its

More information

Industrial Vacuums, Inc

Industrial Vacuums, Inc Instructions/Spare Parts Manual Nilfisk Model GWD255 Drum Top Vacuum CAUTION: This Nilfisk vacuum cleaner is not to be used in explosion-hazardous areas, as serious injury could result. Under no circumstances

More information

GULPER 16SV 16 GALLON WET/DRY VACUUM WITH FRONT MOUNT SQUEEGEE

GULPER 16SV 16 GALLON WET/DRY VACUUM WITH FRONT MOUNT SQUEEGEE GULPER 16SV 16 GALLON WET/DRY VACUUM WITH FRONT MOUNT SQUEEGEE INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS This operator s book has important information for the use and safe operation of this machine.

More information

User, Installation and Servicing Instructions. Silverlink 600 Gas Griddles GS4 and GS7 IS212 ECN3592

User, Installation and Servicing Instructions. Silverlink 600 Gas Griddles GS4 and GS7 IS212 ECN3592 User, Installation and Servicing Instructions Silverlink 600 Gas Griddles GS4 and GS7 IS212 ECN3592 INSTALLATION AND SERVICING INSTRUCTIONS Please read the following carefully before commencing work on

More information

INSTALLATION AND MAINTENANCE GUIDE TRENDY 1000 T ELECTRONIC LAVATORY FAUCET

INSTALLATION AND MAINTENANCE GUIDE TRENDY 1000 T ELECTRONIC LAVATORY FAUCET INSTALLATION AND MAINTENANCE GUIDE TRENDY 1000 T ELECTRONIC LAVATORY FAUCET 1 INDEX 1 TECHNICAL DATA 2 TEMPERATURE ALTERNATIVES 3 PACK CONTENTS 4 PRE-INSTALLATION INFO 5-6 FAUCET INSTALLATION 7 ADJUSTING

More information

MNEFDD54 & MNBCDD54 GALVANIZED WALL FANS Installation, Operation, and Maintenance Instructions

MNEFDD54 & MNBCDD54 GALVANIZED WALL FANS Installation, Operation, and Maintenance Instructions FARM PRODUCTS DIVISION MEMBER OF AMCA AMERICAN COOLAIR CORPORATION P.O. BOX 2300 JACKSONVILLE, FLORIDA 32203 PHONE (904) 389-3646 FAX (904) 387-3449 E-MAIL - fans@coolair.com MNEFDD54 & MNBCDD54 GALVANIZED

More information

Operating Instructions

Operating Instructions Operating Instructions BA-003 Read and understand this manual before use. Keep this manual for future reference. CONFORMS TO UL STD.No.1017 Certified to CSA STD C22.2 No.243-10 For questions or concerns

More information

Enzo Concealed Shower Mixing Valve

Enzo Concealed Shower Mixing Valve Enzo Concealed Shower Mixing Valve EZ40010CP, EZ40013CP & EZ40014CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible.

More information

MK 8706 / MB 8706 CONCEALED THERMOSTATIC SHOWER VALVE INSTALLATION GUIDE

MK 8706 / MB 8706 CONCEALED THERMOSTATIC SHOWER VALVE INSTALLATION GUIDE MK 8706 / MB 8706 CONCEALED THERMOSTATIC SHOWER VALVE INSTALLATION GUIDE DIMENSIONS 150mm 55mm 200mm 67mm Hot water ¾ BSP Parallel Cold water ¾ BSP Parallel 160mm x 120mm aperture behind face plate for

More information

Operating Manual. Model: Float-Controlled Condensate Trap, PN Safety instructions. 2 General description and usage

Operating Manual. Model: Float-Controlled Condensate Trap, PN Safety instructions. 2 General description and usage Model: 1090 1 Safety instructions Float-Controlled Condensate Trap, PN 16 1.1 Proper use Any improper use, intervention in the design and deviation from the design data automatically lead to termination

More information

Steam Trap BK 45 BK 45-U BK 45-LT BK 46

Steam Trap BK 45 BK 45-U BK 45-LT BK 46 Steam Trap BK 45 BK 45-U BK 45-LT BK 46 Original Installation Instructions 810437-08 Contents Foreword... 3 Availability... 3 Formatting features in the document... 3 Safety... 3 Use for the intended purpose...

More information

Troubleshooting the MPH 24FP Series Pedestal Hydrant

Troubleshooting the MPH 24FP Series Pedestal Hydrant MAPA Products P.O. Box 129 Naples, Texas 75568 Toll Free: 877 897 2371 How the Hydrant Works: Troubleshooting the MPH 24FP Series Pedestal Hydrant The design of the hydrant assembly is based on a venturi

More information

Model: 1200 Model: 1200-G Model: 1200-N Float-Controlled Condensate Trap, PN 40

Model: 1200 Model: 1200-G Model: 1200-N Float-Controlled Condensate Trap, PN 40 1 Safety instructions Model: 1200 Model: 1200-G Model: 1200-N Float-Controlled Condensate Trap, PN 40 1.1 Proper use Any improper use, intervention in the design and deviation from the design data automatically

More information

Telo Shower Mixing Valve TL10016CP

Telo Shower Mixing Valve TL10016CP Telo Shower Mixing Valve TL10016CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept any responsibility

More information

SAN RAPHAEL PRESSURE LITE VITREOUS CHINA SIPHON JET TOILET

SAN RAPHAEL PRESSURE LITE VITREOUS CHINA SIPHON JET TOILET SAN RAPHAEL PRESSURE LITE VITREOUS CHINA SIPHON JET TOILET BEFORE YOU BEGIN HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials,

More information

COBRA -H EXTRACTOR 120V

COBRA -H EXTRACTOR 120V COBRA -H EXTRACTOR 120V INFORMATION & OPERATING INSTRUCTIONS CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

More information

Inta City Concealed Shower Mixing Valve CT80010CP

Inta City Concealed Shower Mixing Valve CT80010CP Inta City Concealed Shower Mixing Valve CT80010CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept

More information

Plus Bath Shower Mixing Valve CP and PL30020CP

Plus Bath Shower Mixing Valve CP and PL30020CP Plus Bath Shower Mixing Valve 920000CP and PL30020CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot

More information

Decade Tap Range. Installation Instructions & User Guide. Please keep these instructions for future reference and request of replacement parts

Decade Tap Range. Installation Instructions & User Guide. Please keep these instructions for future reference and request of replacement parts Decade Tap Range Installation Instructions & User Guide Please keep these instructions for future reference and request of replacement parts Contents Thank you for choosing Bristan, the UK s leading taps

More information

Model: 1100 Float-Controlled Condensate Trap, PN 25

Model: 1100 Float-Controlled Condensate Trap, PN 25 1 Safety instructions Model: 1100 Float-Controlled Condensate Trap, PN 25 1.1 Proper use Any improper use, intervention in the design and deviation from the design data automatically lead to termination

More information

Enzo Safe Touch Thermostatic Shower EZ10010CP & EZ10014CP

Enzo Safe Touch Thermostatic Shower EZ10010CP & EZ10014CP Enzo Safe Touch Thermostatic Shower EZ10010CP & EZ10014CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot

More information

DS series STERLING PUMPS. Industrial End Suction Pumps ISO/DP

DS series STERLING PUMPS. Industrial End Suction Pumps ISO/DP DS series Industrial End Suction Pumps ISO/DP 5199 www.sterlingpumps.com.au DS series Capacities from: Heads from: 340 to 5,680 m3/h (1,500 to 25,000 USPGM) 21 to 106 metres (70 to 350 feet) Power range

More information

Mechanical seals external, single or double, to DIN EN 12756

Mechanical seals external, single or double, to DIN EN 12756 INSTALLATION AND OPERATING MANUAL Translation of the original manual Series SCK Bearing pedestal group: 0 Mechanical seals external, single or Keep for future use! This operating manual must be strictly

More information

XC-18. NOTE: *Machine shown without Lift-Up Safety Guard. This guard is included with machine. Machine should not be operated without this guard.

XC-18. NOTE: *Machine shown without Lift-Up Safety Guard. This guard is included with machine. Machine should not be operated without this guard. XC-18 NOTE: *Machine shown without Lift-Up Safety Guard. This guard is included with machine. Machine should not be operated without this guard. EXTREMA MACHINERY COMPANY, INC. PO BOX 1450, ALBANY, LOUISIANA

More information

HOT WASHER MODEL NO: KING150

HOT WASHER MODEL NO: KING150 WARNING: Do not use the hot washer without reading this manual HOT WASHER MODEL NO: KING150 PART NO: 7320175 OPERATION & MAINTENANCE INSTRUCTIONS LS1215 INTRODUCTION Thank you for purchasing this CLARKE

More information

Model Combination Shower Eye/Face Wash

Model Combination Shower Eye/Face Wash INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS 1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424 E-mail: haws@hawsco.com website: www.hawsco.com Model 8300.158 Combination Shower

More information

Enzo and Enzo Deluxe Safe Touch Thermostatic Shower EN10031CP & EN10035CP

Enzo and Enzo Deluxe Safe Touch Thermostatic Shower EN10031CP & EN10035CP Enzo and Enzo Deluxe Safe Touch Thermostatic Shower EN10031CP & EN10035CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as

More information

OPERATOR S MANUAL. For BURLY ATTACHMENTS

OPERATOR S MANUAL. For BURLY ATTACHMENTS OPERATOR S MANUAL For BURLY ATTACHMENTS April 4, 2018 Clod-Buster Topsoil Screener LIMITED WARRANTY Burly Attachments, LLC warrants to the original Purchaser, all products, manufactured by it, to be free

More information

INSTRUCTION MANUAL W-400

INSTRUCTION MANUAL W-400 USE and MAINTENANCE INSTRUCTION MANUAL Bellaria WBX WB GRAVITY SPRAY GUN Series LPH-400 WB en it fr es pt de se TECHNICAL DATA Classic Plus Series LPH-400 (LVLP) Classic Plus Nozzle_Needle set Combination

More information

Airfield Industrial Estate Hixon Staffordshire ST18 0PF

Airfield Industrial Estate Hixon Staffordshire ST18 0PF Deluge Thermostatic Basin Mixer IT1002CP Installation and Maintenance Instructions Intatec Ltd Airfield Industrial Estate Hixon Staffordshire ST18 0PF In this procedure document we have endeavoured to

More information

Model ESFR-17 Dry Type Pendent Sprinklers Early Suppression Fast Response 16.8 K-factor General Description

Model ESFR-17 Dry Type Pendent Sprinklers Early Suppression Fast Response 16.8 K-factor General Description Technical Services 800-381-9312 +1-401-781-8220 www.tyco-fire.com Model ESFR-17 Dry Type Pendent Sprinklers Early Suppression Fast Response 16.8 K-factor General Description The TYCO Model ESFR-17 Dry

More information

MC2000 OPERATING AND CALIBRATION INSTRUCTIONS

MC2000 OPERATING AND CALIBRATION INSTRUCTIONS MC2000 OPERATING AND CALIBRATION INSTRUCTIONS CONTENTS 1 - CERTIFICATE OF CONFORMITY... 3 2 - PRESENTATION... 4 2. 1 - GENERAL... 4 2. 2 - CHARACTERISTICS... 4 2. 3 - OPERATING PRINCIPLE... 5 2. 3. 1 -

More information

Friwa Compact. Operating instructions EN

Friwa Compact. Operating instructions EN Operating instructions EN Version 1.1 / Edition 09/2013 Contents 1 Key background information... 3 1.1 Limitation of liability... 3 1.2 Responsibilities of the operator... 3 1.3 Documentation... 3 1.3.1

More information

CAUTION UM120W (RIGHT TANK) FOR WATER BORNE PAINTS ONLY UM120W (RIGHT TANK) SECTION IS NOT DESIGNED FOR USE WITH SOLVENT BASED PAINT

CAUTION UM120W (RIGHT TANK) FOR WATER BORNE PAINTS ONLY UM120W (RIGHT TANK) SECTION IS NOT DESIGNED FOR USE WITH SOLVENT BASED PAINT OPERATING MANUAL SOLVENT AND WATER BASE SPRAY GUN CLEANER UG5000W and UG5500W CAUTION UM120W (RIGHT TANK) FOR WATER BORNE PAINTS ONLY UM120W (RIGHT TANK) SECTION IS NOT DESIGNED FOR USE WITH SOLVENT BASED

More information

Enzo Safe Touch Thermostatic Shower EZ20011CP & EZ20012CP

Enzo Safe Touch Thermostatic Shower EZ20011CP & EZ20012CP Enzo Safe Touch Thermostatic Shower EZ20011CP & EZ20012CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot

More information

Installation Manual PS-200 & PS-201

Installation Manual PS-200 & PS-201 Installation Manual PS-200 & PS-201 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal

More information

PVC Ductwork Model. Installation and Maintenance for

PVC Ductwork Model. Installation and Maintenance for Installation and Maintenance for PVC Ductwork Model WARNING! These installation instructions are for qualified and experienced technicians in the H.V.A.C. and Fire Protection field only. Failure to follow

More information

H-16.5 Record Cleaning Machine Setup and Instruction Manual

H-16.5 Record Cleaning Machine Setup and Instruction Manual H-16.5 Record Cleaning Machine Setup and Instruction Manual VPI INDUSTRIES, INC., 77 CLIFFWOOD AVE., #3B, CLIFFWOOD, NJ 07721 PHONE: 1-732-583-6895, FAX: 1-732-946-8578 http://www.vpiindustries.com 1 Table

More information

Thermostatic mixing valves with interchangeable cartridges

Thermostatic mixing valves with interchangeable cartridges www.caleffi.com R37. Thermostatic mixing valves with interchangeable cartridges Installation, commissioning and servicing instructions 3 Series Function The thermostatic mixing valve is used in systems

More information

Installation Instructions for. OmniFount

Installation Instructions for. OmniFount Installation Instructions for OmniFount Congratulations, you have just purchased the finest watering fountain on the market. This unit is built to give you excellent service when properly installed and

More information

Semi-Automatic Suction Screen Filters 3"-4 Angle. Service & Maintenance Manual

Semi-Automatic Suction Screen Filters 3-4 Angle. Service & Maintenance Manual Semi-Automatic Suction Screen Filters 3"-4 Angle Service & Maintenance Manual Safety Instructions Prior to installation or handling of the filter, read the Installation and Operation instructions carefully.

More information

Swaging Machine Type H50-46ECO

Swaging Machine Type H50-46ECO ENDEAVOUR Int. Ltd. Tel +44 (0) 1225 446770 Fax +44 (0) 1225 446775 USER MANUAL Swaging Machine Type H50-46ECO Website: www.hydralok.net CONTENTS WARRANTY CONDITIONS... 3 EC DECLARATION OF CONFORMITY...

More information

Smile Tap Range. Installation Instructions & User Guide. Please keep these instructions for future reference and request of replacement parts

Smile Tap Range. Installation Instructions & User Guide. Please keep these instructions for future reference and request of replacement parts Smile Tap Range Installation Instructions & User Guide Please keep these instructions for future reference and request of replacement parts Contents Thank you for choosing Bristan, the UK s leading taps

More information

SuperKlean Washdown Products

SuperKlean Washdown Products DURAREEL DR8 & DR8S INSTALLATION AND MAINTENANCE INSTRUCTIONS **DO NOT THROW AWAY AFTER INSTALLATION** **SAVE AND DISPLAY PROMINENTLY WHERE THIS EQUIPMENT IS USED** GENERAL WARNINGS High pressure and hot

More information

Kinetic. Logic. Astin. THERMOSTATIC INLINE CONTROL SHOWER VALVES Installation & aftercare instructions. Please retain for future reference

Kinetic. Logic. Astin. THERMOSTATIC INLINE CONTROL SHOWER VALVES Installation & aftercare instructions. Please retain for future reference THERMOSTATIC INLINE CONTROL SHOWER VALVES Installation & aftercare instructions Please retain for future reference DUAL INLINE CONCEALED VALVE SKN0201, SAS0201, SLG0202 SKN0202, SAS0205 TRIPLE INLINE CONCEALED

More information

Model A Pipe Line Strainer 3, 4, 6, 8 & 10 Inch (DN80, DN100, DN150, DN200 & DN250) 175 psi (12,1 bar) General Description.

Model A Pipe Line Strainer 3, 4, 6, 8 & 10 Inch (DN80, DN100, DN150, DN200 & DN250) 175 psi (12,1 bar) General Description. Technical Services: Tel: (00) 31-9312 / Fax: (00) 91-5500 Customer Service/Sales: Tel: (1) 50-5000 / (00) 55-523 Fax: (1) 50-5010 / (00) -1295 Model A Pipe Line Strainer 3,,, & 10 Inch (DN0, DN100,, DN200

More information

BARRINGTON PRESSURE LITE VITREOUS CHINA SIPHON JET TOILET K-4327

BARRINGTON PRESSURE LITE VITREOUS CHINA SIPHON JET TOILET K-4327 BARRINGTON PRESSURE LITE VITREOUS CHINA SIPHON JET TOILET K-4327 BEFORE YOU BEGIN INSTALLER HAZARD NOTIFICATION WARNING: Risk of injury or water damage. Contents of vessel under pressure can cause severe

More information

Safety. Rinse Kit for Multi-Pro 1200 and 1250 Turf Sprayers Model No Safety and Instructional Decals. Installation Instructions

Safety. Rinse Kit for Multi-Pro 1200 and 1250 Turf Sprayers Model No Safety and Instructional Decals. Installation Instructions Rinse Kit for Multi-Pro 1200 and 1250 Turf Sprayers Model No. 106-4842 Form No. 3353-529 Rev B Installation Instructions Note: Determine the left and right sides of the machine from the normal operating

More information

WELLWORTH WATERGUARD VITREOUS CHINA SIPHON JET TOILET

WELLWORTH WATERGUARD VITREOUS CHINA SIPHON JET TOILET WELLWORTH WATERGUARD VITREOUS CHINA SIPHON JET TOILET 1. BEFORE YOU BEGIN HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials,

More information

Installation Manual PS-225 & PS-275

Installation Manual PS-225 & PS-275 Installation Manual PS-225 & PS-275 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal

More information

OPERATING MANUAL SOLVENT SPRAY GUN CLEANERS UG5000E, UG5000DVM AND UG5500E UNI-RAM CORPORATION ONTARIO CANADA PATENTS

OPERATING MANUAL SOLVENT SPRAY GUN CLEANERS UG5000E, UG5000DVM AND UG5500E UNI-RAM CORPORATION ONTARIO CANADA PATENTS OPERATING MANUAL SOLVENT SPRAY GUN CLEANERS UG5000E, UG5000DVM AND UG5500E PATENTS USA 4,788,836 CANADA USA 5,213,117 ENGLAND EUROPE 0300248 ITALY SWEDEN 0300248 GERMANY FRANCE 8110528.0 JAPAN UNI-RAM

More information

Audi-Larm Audible Alarm

Audi-Larm Audible Alarm Audi-Larm Audible Alarm MAINTENANCE AND REPAIR TAL 1706 (L) Rev. 7 MSA 2017 Prnt. Spec. 10000005389(I) Mat. 10093084 Doc. 10093084 REPLACEMENT KITS AND PARTS LIST TAL 1706 (L) Rev. 7-10093084 2 Exploded

More information

Operator s Manual. 6 Gallon Model No. VQ607SFD FOR YOUR SAFETY. Read and understand this manual before use Keep this manual for future reference

Operator s Manual. 6 Gallon Model No. VQ607SFD FOR YOUR SAFETY. Read and understand this manual before use Keep this manual for future reference Wet/Dry Vacuums Operator s Manual 6 Gallon Model No. VQ607SFD FOR YOUR SAFETY Read and understand this manual before use Keep this manual for future reference www.vacmaster.com Cleva North America 44 Parkway

More information

Operating Instructions

Operating Instructions Operating Instructions Varioset Standard After-sales service For after-sales service please contact the Veit representative in your country. GmbH & Co. Justus - von - Liebig - Str. 15 D - 86899 Landsberg

More information

USE and MAINTENANCE INSTRUCTION MANUAL GRAVITY. WS-400 EVO LS-400 Entech. SPRAY GUN Series. en it fr es pt de se

USE and MAINTENANCE INSTRUCTION MANUAL GRAVITY. WS-400 EVO LS-400 Entech. SPRAY GUN Series. en it fr es pt de se USE and MAINTANCE INSTRUCTION MANUAL WS-400 EVO LS-400 Entech GRAVITY SPRAY GUN Series en it fr es pt de se TECHNICAL DATA WS-400 WS-400 EVO WS-400 Clear WS-400 Base WS-400-1301 EVO 1.3 170 365 260 WS-400-1401

More information

GRUNDFOS INSTRUCTIONS. Sololift2 C-3. Installation and operating instructions

GRUNDFOS INSTRUCTIONS. Sololift2 C-3. Installation and operating instructions GRUNDFOS INSTRUCTIONS Sololift2 C-3 Installation and operating instructions English (US) English (US) Installation and operating instructions Original installation and operating instructions. CONTENTS

More information

Operating Instructions. Boilermag XL Filter. High Intensity Magnetic Separator

Operating Instructions. Boilermag XL Filter. High Intensity Magnetic Separator Operating Instructions Boilermag XL Filter High Intensity Magnetic Separator Technical data is subject to change without notice due to technical innovation! Eclipse Magnetics Ltd Atlas Way, Atlas North,

More information

Desoldering Tool. Instruction Manual

Desoldering Tool. Instruction Manual Desoldering Tool Instruction Manual Thank you for purchasing the Hakko 472D desoldering tool with digital temperature display. Please read this manual before operating the Hakko 472D. Keep this manual

More information

Tornado Operations & Maintenance Manual

Tornado Operations & Maintenance Manual TORNADO INDUSTRIES 7401 W. LAWRENCE AVENUE CHICAGO, IL 60706 (708) 867-5100 FAX (708) 867-6968 www.tornadovac.com Tornado Operations & Maintenance Manual MODEL NO. 99690 BD 22/14, 99720 BD 26/14 L9722

More information

55-Gallon Dispenser Package

55-Gallon Dispenser Package INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. 308 666 Rev. A Husky 715 55-Gallon Dispenser Package 100 psi (6.9 bar) Maximum

More information

SuperKlean Washdown Products

SuperKlean Washdown Products February 2012 DURAMIX 8000 INSTALLATION AND MAINTENANCE INSTRUCTIONS **DO NOT THROW AWAY AFTER INSTALLATION** **SAVE AND DISPLAY PROMINENTLY WHERE THIS EQUIPMENT IS USED** WARNING HIGH PRESSURE AND HOT

More information

BOILING UNIT REDITAP. Installation and User Guide. IMPORTANT: This booklet should be left with the user after installation and demonstration

BOILING UNIT REDITAP. Installation and User Guide. IMPORTANT: This booklet should be left with the user after installation and demonstration in tap Boiling water to in tap sink Drain Valve (as high as possible) REDITAP CONNECTION SUMMARY Amp mains supply cold mains water into in tap optional filter cold water in hot water BOILING UNIT Installation

More information

Pump assembly Instruction manual

Pump assembly Instruction manual Instruction manual EN Version 2.0 /Release 06/2012 Table of content 1 Key background information...3 1.1 Limitation of liability...3 1.2 Responsibilities of the operator...3 1.3 Documentation...3 1.3.1

More information

OPERATING MANUAL MANUAL WATER BASE GUN CLEANERS UM120W UNI-RAM CORPORATION ONTARIO CANADA PATENTS

OPERATING MANUAL MANUAL WATER BASE GUN CLEANERS UM120W UNI-RAM CORPORATION ONTARIO CANADA PATENTS OPERATING MANUAL MANUAL WATER BASE GUN CLEANERS UM120W PATENTS USA 4,788,836 CANADA USA 5,213,117 ENGLAND EUROPE 0300248 ITALY SWEDEN 0300248 GERMANY FRANCE 8110528.0 JAPAN UNI-RAM CORPORATION ONTARIO

More information

568X, 587X, 588X Series

568X, 587X, 588X Series Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

Installation Instructions for. CattleMaster Series Fountains

Installation Instructions for. CattleMaster Series Fountains Installation Instructions for CattleMaster Series Fountains Congratulations, you have just purchased the finest watering fountain on the market. This unit is built to give you excellent service when properly

More information

Operation, Maintenance and Installation Manual

Operation, Maintenance and Installation Manual Manual No. FS-OM1-5 1-16 in. FloodSafe Inflow Preventer Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1 INSTALLATION... 2 CONSTRUCTION...

More information

General System Layout Sketch

General System Layout Sketch General System Layout Sketch EZ-37 Solar Panels PV panel Glycol Fill Valve Expansion Tank ` 1 Introduction This document describes how to install a Heliatos GH type solar water heating system. These systems

More information

DRY AIR SYSTEMS, INC Metro Boulevard Maryland Heights, Missouri (314) fax (314)

DRY AIR SYSTEMS, INC Metro Boulevard Maryland Heights, Missouri (314) fax (314) DRY AIR SYSTEMS, INC. 2655 Metro Boulevard Maryland Heights, Missouri 63043 (314) 344-1114 fax (314) 344-0677 HD SERIES DRIERS TABLE OF CONTENTS WHY AN AIR DRYER 3 WHAT IS A DESICCANT AIR DRYER 3 Desiccant

More information

F-CLASS MODEL M6L WET CHEMICAL FIRE EXTINGUISHER Installation, Operation, Recharge and Maintenance Manual

F-CLASS MODEL M6L WET CHEMICAL FIRE EXTINGUISHER Installation, Operation, Recharge and Maintenance Manual F-CLASS MODEL M6L WET CHEMICAL FIRE EXTINGUISHER Installation, Operation, Recharge and Maintenance Manual 008094 All fire extinguishers should be installed, inspected and maintained in accordance with

More information

Installation, Operation and Maintenance Guide AP3900 Series Thermostatic Mixing Valves

Installation, Operation and Maintenance Guide AP3900 Series Thermostatic Mixing Valves Note: Please provide valve serial number (stamped on cover of valve) when ordering parts. Hot Water Tempered Water Outlet Cold Water Tempered Water Outlet Redundant Thermostatic Mixing Valve Hot Water

More information

MODEL 7000 SUCTION UNIT

MODEL 7000 SUCTION UNIT MODEL 7000 SUCTION UNIT OPERATOR S MANUAL Caution Federal law restricts this device to sale by or on order of a physician, or any other practitioner licensed by the law of the State in which he practices

More information

SSS BPV- 40 Backpack Vacuum

SSS BPV- 40 Backpack Vacuum SSS BPV- 40 Backpack Vacuum Manual The contents of this manual are based on the latest product information available at the time of publication. Triple S reserves the right to make changes or improvements

More information

Deluge Concealed Shower Mixing Valve DL40010CP

Deluge Concealed Shower Mixing Valve DL40010CP Deluge Concealed Shower Mixing Valve DL40010CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept

More information

SAFETY, OPERATION AND MAINTENANCE MANUAL. MX-1408 SELF-CONTAINED EXTRACTOR This unit is intended for commercial use.

SAFETY, OPERATION AND MAINTENANCE MANUAL. MX-1408 SELF-CONTAINED EXTRACTOR This unit is intended for commercial use. SAFETY, OPERATION AND MAINTENANCE MANUAL MX-1408 SELF-CONTAINED EXTRACTOR This unit is intended for commercial use. READ & FOLLOW ALL INSTRUCTIONS, WARNINGS & CAUTIONS BEFORE USING THIS EXTRACTOR This

More information

Technical Specifications: Your product has a high quality finish and should be treated with care to preserve the visible surfaces.

Technical Specifications: Your product has a high quality finish and should be treated with care to preserve the visible surfaces. 3 Remove concealing plate KIRI Concealed Mixer Valve ABS Undo nuts (9) on both hot and cold inlets and remove filter washer KIRI VA (6) Installation Instructions & Maintenance Guide 5 Rinse filter washers

More information

OPERATING MANUAL SPRAY GUN CLEANERS UG UG3000 SERIES UNI-RAM CORPORATION ONTARIO CANADA PATENTS

OPERATING MANUAL SPRAY GUN CLEANERS UG UG3000 SERIES UNI-RAM CORPORATION ONTARIO CANADA PATENTS OPERATING MANUAL SPRAY GUN CLEANERS UG1000 - UG3000 SERIES PATENTS USA 4,788,836 CANADA USA 5,213,117 ENGLAND EUROPE 0300248 ITALY SWEDEN 0300248 GERMANY FRANCE 8110528.0 JAPAN UNI-RAM CORPORATION ONTARIO

More information

FSW300 Series Flow Switch

FSW300 Series Flow Switch . FSW300 Series Flow Switch - 2 - Series FSW300 Series FSW300 Table of contents page 0 About this operating manual... 4 1 Device description... 5 1.1 Intended use... 5 1.1.1 Reed contact - Switching of

More information

Kiko Bath Shower Mixing Valve KK90015CP

Kiko Bath Shower Mixing Valve KK90015CP Kiko Bath Shower Mixing Valve KK90015CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept any responsibility

More information

Pump Out Vacuums Polyethylene & Steel

Pump Out Vacuums Polyethylene & Steel Pump Out Vacuums Polyethylene & Steel Operations and Parts Manual 110 volt receptacle on single motor only Models: 415P-AD 429P-AD 415DS IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance,

More information

LC Series - Light Commercial Pump Station Installation and Operation Manual

LC Series - Light Commercial Pump Station Installation and Operation Manual LC Series - Light Commercial Pump Station Installation and Operation Manual Please keep this manual with the pump station Content Rain Bird LC Series Overview... Safety Instruction... Operation... 3 Pump

More information

Model 8300FP Freeze Resistant Combination Shower Eye/Face Wash

Model 8300FP Freeze Resistant Combination Shower Eye/Face Wash INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS 1455 Kleppe Lane Sparks, NV 8941-6467 (775) 59-4712 Fax (775) 59-7424 E-mail: haws@hawsco.com website: www.hawsco.com Model 800FP Freeze Resistant Combination

More information

INSTALLATION & TESTING MANUAL

INSTALLATION & TESTING MANUAL INSTALLATION & TESTING MANUAL ***CAUTION: Do not lift by yellow enclosure. Reference installation instructions for proper lifting and moving techniques. IMPROPER INSTALLATION MAY RESULT IN RISK OF SCALDING

More information

Burgess. Electric Professional Fogger. CAUTION: Read and follow all instructions

Burgess. Electric Professional Fogger. CAUTION: Read and follow all instructions Burgess Electric Professional Fogger CAUTION: Read and follow all instructions Do Not Return This Fogger To The Store For Help, Information or Parts, Call : 1-800-311-9903 The Fountainhead Group, Inc.

More information