Pumpco Sdn. Bhd. Solar Water Heater. 1 of 8 MAIN FEATURES OF SOLARMATE

Transcription

1 Pumpco Sdn. Bhd. Solar Water Heater Solar Water SOLARMATE MAIN FEATURES OF SOLARMATE SOLAR WATER TANKFlat base shaped storage tank ideal for inclined roof with 0.5mm thick aluminium base plate.1.2mm thick stainless steel storage cylinder; ensure long life span.1.5mm thick stainless steel (Premier s)30mm - 160mm thick high density cosmonate foam insulation for maximum heat retention.3kw Electrical booster with safety thermostat (built-in).0.7mm thick durable non-rust outer aluminium casing.double riser tubes system for greater heat transfer from solar thermal panels, and roofs with incline of less than 5 degrees. 1 of 8

2 Heat Pump Other INTRIX Heat pump Intrix Heat Pump consists of two models. The Air Source Heat Pump Series uses ambient air as the main source of energy. The Water Source Heat Pump series uses water as the main source of energy. This can be from chilled water or from a cooling tower. How Heat Pump WorksHeat Pump technology makes use of solar energy from the environment and transfers it to a water heater system. Heat from a renewable and free heat source such as the ambient air and chiller water is harvested and raised to a higher temperature for use in the hot water system. With a minimum energy input into the compressor, an output of heat is achieved with a multiple of 3-6 times of the input. Comparing to a conventional water heater, Intrix Heat Pump achieves up to 80% of energy saving. The process begins 1. At the evaporator, liquid refrigerant absorbs heat from the environment causing it to evaporate. 2. The refrigerant, now in a gaseous state is moved to the compressor where it is compressed, causing it to rise in temperature. 3. The compressed (and hot) refrigerant then moves to the condenser where the heat is transferred to the water heating system. This transfer of heat causes the refrigerant to change back to a liquid state. 4. The refrigerant, now in a liquid state moves through the expansion valve, reducing its pressure. 5. The liquid refrigerant returns once again to the evaporator and the cycle repeats. Intrix Heat Pump is up to 5 times more efficient than standard or traditional heating system. It has a lower operating cost compared to fossil fuel options. This translates to cost savings. To further improve on savings, each unit is able to continuously monitor and log data in real-time. Critical data such as hot water usage patterns and heat pump status are analysed and synced with the Building Management System (BMS). The Smart Control System is also able to perform offpeak tariff optimization by enabling optimal use of electricity during "off peak hours" and increased savings on "maximum demand charges". This results in significant savings compared to a regular thermostat controlled system. The Smart Control System can be made into a Master-slave Network whereby a centralized unit controls up to a maximum of 255 units of Heat Pump and Thermal Energy Storage. The auto service rotation ensures that all Heat are used equally to prevent underuse of any particular unit. With an automatic backup, continuous heated water supply is ensured in the event of a Heat Pump unit failure. Besides the cost savings, Intrix Heat Pump emits less CO2 per kwh of heating and emits lesser harmful SOx and NOx. Other features includes a maximum of 70oC to ensure pathogen free hot water as high temperatures prevent the growth of the Legionella bacteria. Utilising Intrix's patented LETTM COP Enhancement Technology results in increased output, efficiency and energy savings. Each unit is integrated with a soft starter which prevents overloading and reduces interference to other electrical appliances when the system is started up. The evaporator system of the device is engineered and built 2 of 8

3 utilising materials and manufacturing processes that enhance its anticorrosion properties, making it suitable for sea-side installation. Multipoint Water Heater Tankless INTRIX INTRIX ecompact Instantaneous heater - designed for an inexhaustible supply of water heater. Provide Hotel Standard Bathroom in your house Endless hot water supply Zero waiting time Ceiling conceal installation Space saving compact design - allows flexible mounting options, with simple piping and installation, even with limited available space Child safety - designed with scalding prevention in mind, the temperature can be limited to 41 degree celcius NO STANDING HEAT LOSS! 40% saving compared to storage water heater. (Based on US Energy Department & Monash University Malaysia Campus research) CR CR Process water systems, Washing and cleaning systems, Seawater systems, Pumping of acids and alkalis, Ultrafiltration systems, Reverse osmosis systems, Swimming baths Water supply The basic CR pump range, which can be applied in almost any industrial solution, is already in itself the broadest range available. Through our modular approach, we have made it even broader. The basic CR pump range is available in four different materials: cast iron, two grades of stainless steel, and all-titanium. There are eleven flow sizes, capable of producing up to almost 50 bar of pressure, and with a variety of shaft seals, rubber materials and supply voltages. Pump parts which are typically vulnerable to difficult liquids or particularly demanding operating conditions can be optimised for their purpose and designed for specific requirements. s CR pumps provide a complete range of pump solutions so that all applications, industrial and domestic, can benefit from the Grundfos touch. The applications that can be covered include the following: and benefits Reliability High efficiency Service-friendly Space-saving Suitable for slightly aggressive liquids High corrosion resistance 3 of 8

4 Single-pump solution making high pressures possible. HOT SELLING PRODUCT!! CM3-5, CM4-5 Home use water pump CM Booster, CME Booster comes in different versions: CME Booster CM Booster PM2 CM Booster PM1 CM Booster PT The CME Booster provides constant water pressure for a variety of domestic applications. This means that the end-user is no longer bothered by fluctuations in water pressure due to a rise or fall in demand, or from pump starts and stops. CME Booster keeps the pressure within the home up regardless of usage. The constant pressure feature provides the benefit of increased comfort. In addition the CME Booster makes it possible to personalise the water pressure. By the touch of a button the pressure level is increased or decreased as desired. Constant pressure via integrated speed control Compact Robust, stainless steel Easy installation Dry-running protection Low noise, 55 db Grundfos has taken the mystery out of controlling variable water pressure for the end-user. With a CM Booster PM2 complex operation and cryptic parameters are a thing of the past. The CM Booster combined with the PM2 provides adjustable pressure settings. The enduser is in control with regards to selecting the water pressure he prefers for pump start-up. Compact Easy installation Automatic resetting of alarms Adjustable pressure settings Dry-running protection Anti cycling (leakage detection) Maximum continuous operating time The Grundfos CM Booster PM1 is a compact booster set for water supply in domestic applications. The pressure booster consists of a Grundfos CM pump and a Grundfos Pressure Manager PM1. The pressure manager allows the pump to start and stop automatically according to demand and protects the pump from dry-running. Compact Easy installation Automatic resetting of alarms Adjustable pressure settings Dry-running protection Anti cycling (leakage detection) Maximum continuous operating time 4 of 8

5 The Grundfos CM Booster PT is an automatic booster system for water supply in domestic and agricultural applications as well as other installations where small leakages are expected to occur. The booster system consists of a Grundfos CM pump, a pressure tank and a pressure switch assembled into one unit. The tank is delivered with the product and is easily connected to the CM pump. The system is now ready for use, with preset start pressure and compliant tank precharge pressure. The pressure band is approximately 1 bar. When the system has been connected to the pipework, it is all a matter of inserting the plug into a power supply socket, and the system is operational. CM pump Pressure tank to minimise the number of pump starts Motor protection (single-phase only) Automatic operation. The Grundfos CM Booster PS is an automatic booster system for water supply in domestic and agricultural applications as well as other installations where small leakages are expected to occur. The booster system consists of a Grundfos CM pump, a 5-way valve and a pressure switch. A pressure tank must be fitted to complete the booster system. Use your own pressure tank or order one of the Grundfos GT-tanks that make a perfect fit for your booster system. The pressure band is approximately 1 bar. When the system has been connected to the pipework, it is all a matter of inserting the plug into a power supply socket, and the system is operational. CM pump pressure tank to minimise the number of pump starts motor protection (single-phase only) automatic operation. s in private homes in summer houses and weekend cottages on farms in market gardens and other large gardens. Blocks of flats Schools Small hotels or guest houses Small office buildings The pump is suitable for pumping of potable water and rainwater. Horizontal Split Casing Pump HS Air-conditioning/heating systems, Public water supply, District cooling/heating plants, Cooling systems, Public waterworks, Process cooling, Irrigation Water Supply The Grundfos HS horizontal split case pump is a single-stage, non-selfpriming, between bearing, centrifugal volute pump. The axially split design allows easy removal of the top casing and access to the pump components (bearings, wear rings, impeller, and shaft seal) without 5 of 8

6 disturbing the motor or pipework. The independent bearing housing allows for ease of maintenance without removing the top casing. The double volute design reduces the radial load on the shaft, extending component life, minimising vibration and providing quiet operation. The HS pump also offers high pump efficiencies throughout the range. High energy efficiency along with long pump life and easy maintenance add up to low life-cycle costs. The HS pump is available in three configurations pump with motor and baseframe, pump with baseframe, and bare shaft pump only. The HS pump is ideal for custom applications and is available in a wide range of variants. The high efficiency and low life cycle costs make the HS ideal for any commercial building, water utility or industrial project. and benefits Easy to service: split case design Double suction minimises axial load,which extends the life of the wear rings, shaft seals and bearings Double volute reduces radial forces and minimises noise and vibration Independent bearing housing design allows access to the pump components without removing the top half of the casing High energy efficiency Low life-cycle costs Many product variants available. SP Submersible Pump Submersible & Sump SP Groundwater supply to waterworks, Irrigation in horticulture and agriculture, Groundwater lowering, Pressure boosting, Industrial applications Water Supply Grundfos SP submersible pumps are renowned for their high efficiency and reliability throughout the range. Made entirely of corrosion-resistant stainless steel, SP pumps are ideal for a wide variety of applications. Grundfos SP pumps represent state-of-the-art hydraulic design. Built to deliver optimum efficiency during periods of high demand, the SP pumps provide low long-term costs and high operating reliability regardless of the application. The Grundfos SP range offers high efficiency, high resistance to sand and other abrasives, motor burnout protection, and easy maintenance. A complete monitoring and control system is available for constant optimisation of the pumping system. and benefits State-of-the-art hydraulics provide high efficiency and low operating costs 100 % stainless steel inside and outside Sand resistant Resistant to aggressive water Motor burnout protection Dry-running protection Monitoring, protection and communication via the MP 204 protection unit and the R100 remote control. 6 of 8

7 Hydro Multi-S CM, CMV, CR Offices, Schools, Hotels, Irrigation systems Water Supply Grundfos Hydro Multi-S booster sets consist of two or three identical Grundfos CM, CMV or CR pumps, connected in parallel and mounted on a common base frame, and a control cabinet with motor protection and integrated controller. Hydro Multi-S booster sets are supplied as complete, pre-assembled and tested systems including suction and discharge manifolds, isolating valves, non-return valves, pressure gauge and pressure switches. To ensure reliable operation, the booster set must be fitted with a suitable diaphragm tank. The pumps are automatically operated according to system demand by means of pressure switches (one for each pump). and benefits Reliable highly efficient service-friendly compact easy to commission suitable for emergency operation. End Suction NB, NBG, NBE, NBGE District heating plants, Heating systems for blocks of flats, Air-conditioning systems, Cooling systems, Wash down systems, Other industrial systems Water Supply Grundfos end-suction pumps are used in water supply, industrial pressure boosting, industrial liquid transfer, HVAC (heating, ventilation and air-conditioning), and irrigation. Grundfos end-suction pumps are multi-purpose pumps suitable for a variety of different applications requiring reliable and cost-efficient supply. End-suction pumps are used in five main areas of application: water supply, industrial pressure boosting, industrial liquid transfer, HVAC and irrigation. The Grundfos NB/NBG pumps are all non-self-priming, single-stage, centrifugal volute pumps with axial suction port, radial discharge port and horizontal shaft. The NB/NBG range consists of close-coupled pumps with their main dimensions in accordance with either EN733 or ISO2858. Pumpco Sdn. Bhd. B-262, Jalan Air Putih, 25300, Kuantan, Pahang Tel Tel Fax eric.pumpco@hotmail.com Website 7 of 8

8 8 of 8