Install guide 8010 ENGLISH. Customer Support: or Visit our webiste Made in China
|
|
- Lucas Snow
- 6 years ago
- Views:
Transcription
1 Install guide 8010 ENLISH ustomer Suppt: Visit our webiste Made in hina
2 Install guide 8010 aution Tools 1 Location To avoid electrical shock and to prevent damage to the furnace, air conditioner, and thermostat, disconnect the power supply befe beginning wk. This can be done at the circuit breaker, at the appliance. ou will need #1 Phillips screwdriver (small) and Drill with 3/16-in. (4.8mm) bit f this installation. ï On replacement installations, mount the new thermostat in place of the old one if possible. ï Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the flo, and in a room that is used often. ï Do not install it where there are unusual heating conditions, such as: in direct sunlight; near a lamp, radio, television, radiat register, fireplace; near hot water pipes in a wall; near a stove on the other side of a wall P 1 ï Do not locate in unusual cooling conditions, such as: on a wall separating an unheated room; in a draft from a stairwell, do, window. ï On new Installations, follow the guidelines listed below. ï Do not locate in a damp area. This can lead to crosion that will shten thermostat life. ï Do not locate where air circulation is po, such as: in a cner an alcove; behind an open do. ï Do not install the unit until all construction wk and painting has been completed. ï This thermostat does not require leveling. P 2 ood 5ft. (1.5m) A U T I O N ï our thermostat is a precise instrument. Please handle it with care. ï Turn off electricity to the appliance befe installing servicing thermostat any part of the system. Do not turn electricity back on until wk is completed. ï Do not sht () across electric terminals at control on furnace air conditioner to test the system. This will damage the thermostat and void your warranty. ï All wiring must confm to local codes and dinances. ï This thermostat is designed f use with 24 volt A and millivolt systems. The thermostat should be limited to a maximum of 1.0 amps; higher amperage may cause damage to the thermostat.
3 AS ELET 2 Label ires to Old Unit P 3 ï Switch electricity to the furnace and air conditioner OFF; then proceed with the following steps. ï emove cover from old thermostat. Most are snap-on types and simply pull off. Some have locking screws on the side front. These must be loosened. ï Note the letters printed near the terminals. ï arefully attach labels (enclosed) to each. Label the s one at a time. ou must have all the s labeled befe you proceed. aution DO NOT EMOVE IES FOM OLD THEMOSTAT UNTIL OU HAVE AEFULL LABELED THEM, ITH LABELS POVIDED. THEE IS NO STANDAD OLO ODE FO THESE IES. emove old unit emove the s from the terminals of the old thermostat. ï Make sure the s do not fall back inside the wall. ï ind them around a pencil to keep them from falling. ï emove the old thermostat from the wall. Fill wall opening with fiber glass insulation to prevent drafts. ires in wall come from Furnace and A unit 3 Mount the 8010 ï Separate front from back of unit. rasp the front of the unit and the back of the unit and pull apart. The thermostat body away from the base. ï Hold the base against the wall, with the s coming through the opening below the terminal block. ï Position the base f best appearance ï Attach the base to the wall with the two screws provided. ï If you are mounting the base to sheet rock if you are using the old mounting holes, use the plastic anchs provided. Drill a 3/16-in.(4.8mm) hole f the insert at each screw location, then mount the base. Terminals 2 O H B A P 4
4 AA 4 as-electric Selection ï If you have Electric a Pump you must place the as/electric in the ELET position (thermostat controls the Fan). ï If you have as the as/electric Jumper should be in the AS position (furnace controls the Fan ). O H B P 5 ircuit Board 2 A AS ELET as/ Electric 5 Install Batteries The 8010 requires batteries to operate your system. Switch MODE switch to OFF and the switch to AUTO. ï Insert 2 AA alkaline batteries accding to the polarity noted in the compartment. AA 2 O H B A AS ELET NOTE: eplace the batteries when this LO battery indicat appears on the display once a year. 6 Options Please be aware of the following power options 1) The 8010 can run on batteries only. (2AA Alkaline) The batteries will last well over 1 year. If the batteries are not replaced the thermostat will stop wking. 2) The 8010 can run on the if available. As shown in the wiring diagrams, The is the other side of the 24VA heating transfmer. If the is used, the batteries are not needed. P 6
5 7 ire onnections Befe you onnect ires P 7 Make sure your s are labeled. This is necessary to determine which step-by-step wiring diagram you should use. This may require you to find the 'other end' connection f each on your heating air conditioning equipment and read the label there. If you have a Zoned ing/ooling system with multiple thermostats, please refer to our website at f installation notes call Please refer back to these guidelines f safe and secure connections. ï Take care not to damage the labels f each in handling. ï Strip insulation 3/8 in. (9.5mm) from ends. ï onnect labeled s only to a terminal with cresponding letter. ï Bend the slightly, insert the under the contact plate and tighten the screw down onto the. IE LABEL LIST - Single source power f heat/cool ( connected to aution Do not allow s to touch each other parts on unit. ires must be routed through the hole in the back plate, below the terminal block, they will hit parts on the cover. and H using the ) H - ing - ooling - ing return - Fan return hat ires Do ou Have? The ire Label List shows labels used on itetemp thermostats. Please determine what s you have and select the crect wiring diagram to "go to" on pages 8-9. If you have a HEAT PUMP select a wiring diagram on pg 9. - ompress return H - Humidifier (built into the furnace) 2-2nd stage heat in NOMAL, auxiliary heat in PUMP mode. A - F 3 zoned heating systems - A power f the thermostat if available O - Damper control (Zoned heating) heat pump changeover valve (powered in OOL) B - Damper control (Zoned heating) heat pump changeover valve (powered in HEAT) NOTE: Do not connect both O and B on a heat pump. onnect O to O & tape off B. X - Tape off X E - Tape off E P 8 H o To Page 11 H o To Page 12 And A unit H And A unit H o To Page 13 o To Page 14
6 From Nmal two stage system o To Page 15 2 From heat pump w/o Aux heat o To Page 16 B O From heat pump with Aux heat O B o To Page 17 2 P 9 If you do not find the wiring infmation f your system try our webiste f me infmation call our customer service hotline at ire onnections cont hen you have finished connecting the s attach control unit to wall unit. Hook the top of the body onto the base, swing the body down, and snap the body onto the base. 8 heck Unit Follow these procedures to verify you have crectly installed the unit. To check HEAT mode: ï Set the mode switch to HEAT. Set the fan switch AUTO. ï Adjust the temperature control to raise the target temp to 90 o. ï ait 5 min. ï Verify that heat is blowing from the system. To check OOL mode: ï Set the mode switch to OOL. ï Adjust the temperature control to 5 o below the room temperature. ï ait 5 min. ï Verify that cool air is blowing from the system. Mode Switch To check Fan: (If you connected the ) ï Switch Mode to OFF during fan test. ï Switch the switch to the ON position. Verify air is blowing from vents. ï After test, return to Fan switch to AUTO, and Mode to HEAT OOL Fan Switch ongratulations, you have successfully installed your unit. Please proceed to the OPEATIN uide to initialize the new thermostat. EMEMBE, Mode Switch must be in HEAT OOL to operate. P 10
7 H 2 IE ing (AS MILLIVOLT 24vac STEP 1 - onnect the ( H) to the H terminal on the thermostat. This connects the er to the thermostat. STEP 2 - onnect the to the terminal on the thermostat. This connects the heater control line to the thermostat. our er is now connected to the thermostat. HEAT HEAT FUNAE NOTE: ires marked with P 11 eturn To Page 9 H STEP 1 - onnect the ( H) to the H terminal on the thermostat. This connects to the er. STEP 2 - onnect the to the terminal on the thermostat. This connects the heater control line to the thermostat. H 3 IE FUNAE STEP 3 - onnect the to the terminal on the thermostat. NOTE: ires marked with This connects the Fan to the thermostat. our system is now connected to the thermostat. P 12 eturn To Page 9
8 and A unit H STEP 1 - onnect the to the terminal on the thermostat. This connects to the ooler compress. STEP 2 - onnect the H to the H terminal on the thermostat. This connects the er/ooler. STEP 3 - onnect the to the terminal on the thermostat. This connects to the heater control line. 4 IE NON_HEAT PUMP H HVA SSTEM NOTE: ires marked with ool omp STEP 4 - onnect the to the terminal on the. This connects to the Fan. eturn To Page 9 our HVA system is now connected to the thermostat. P 13 and A unit H STEP 1 - emove the Jumper. STEP 2 - onnect the to the terminal on the thermostat. This connects to the ooler compress. STEP 3 - onnect the H to the H terminal on the thermostat. This connects to the er. STEP 4 - onnect the to the terminal on the thermostat. This connects to the ooling. STEP 5 - onnect the to the terminal on the thermostat. This connects to the heater control line. STEP 6 - onnect the to the terminal on the. This connects to the Fan. our HVA system is now connected to the thermostat. OOL HEAT 5 IE NON_HEAT PUMP emove H HVA SSTEM NOTE: ires marked with eturn To Page 9 ool omp P 14
9 From Nmal two stage system 2 STEP 1 - onnect the to the terminal on the thermostat. This connects the Fan. STEP 2 - onnect the between to. This connects the 1st stage heat. STEP 3 - onnect the between 2 to 2. This connects the 2nd stage heat. STEP 4 - onnect the to the H terminal on the. This connects to the 24vac power. NOMAL 2 Stage System 2 Two Stage Furnace Two Stage System P 15 NOTE: ires marked with our HVA system is now connected to the thermostat. (If the system also has A, connect it per instructions f and on pg 14) eturn To Page 9 and A unit O B STEP 1 - onnect the to the terminal on the thermostat. This connects the Fan. STEP 2 - Add a between and. STEP 3 - onnect the to the terminal on the thermostat. This connects the ompress. STEP 4 - onnect the O B to the O B terminal on the thermostat. (If you have both O and B contact itetemp your local HVA contract f further help) This connects the change over valve. STEP 5 - onnect the to the terminal on the. This connects to the 24vac power. HEAT PUMP w/o Auxiliary 24VA O B O B hange Over Single Stage HEAT PUMP NOTE: ires marked with eturn To Page 9 omp our HVA system is now connected to the thermostat. P 16
10 From heat pump with Aux heat P 17 B 2 O STEP 1 - onnect the to the terminal on the thermostat. This connects the Fan. STEP 2 - Add a between and. STEP 3 - onnect the to the terminal on the thermostat. This connects the ompress. STEP 4 - onnect the O B to the O B terminal on the thermostat. (If you have both O and B s, use the O and tape off the B). This connects the change over valve. STEP 5 - onnect the to the terminal on the. This connects to the 24vac power. STEP 6 - onnect 2 to 2 on the thermostat. This connects the AUX heat. our HVA system is now connected to the thermostat. HEAT PUMP with Auxiliary AUX 24VA O B (not both) O B hange Over HEAT PUMP NOTE: ires marked with eturn To Page 9 omp 8010 Features The 8010 can be used with most 24 volt gas, oil electric heating and air conditioning systems, heat pump systems with without auxiliary heat, Nmal 2 Stage systems, Zoned Hot-ater, Zoned Fced air systems, gas millivolt heating systems. It cannot be used with 120 volt heating systems. Ask The Home Depot f other thermostats to control those systems. The 8010 is digital. ou can program your desired and cool temperature by setting the dial. The unit uses no harmful mercury. A 5-minute minimum off time in OOL protects your air conditioning system from being damaged. Two "AA" batteries (not included) are used to run the thermostat in some installation. "" installations can make batteries last many times longer. P 18
Install guide 8035C ENGLISH Printed in China MENU PROG RESET MENU PROG RESET
Install guide 8035 PO ESET ENLISH PO ESET ustomer Suppt: 888-515-2585 Visit our website www.ritetemp-thermostats.com Printed in hina 1-402-051 Install guide 8035 aution To avoid electrical shock and to
More informationInstall Guide 3M-10 ENGLISH
Install uide 3M-10 ENLISH Install uide 3M-10 aution Tools Location To avoid electrical shock and to prevent damage to the furnace, air conditioner, and thermostat, disconnect the power supply before beginning
More informationInstall guide Customer Support: or Visit our website OFF FAN HEAT COOL AUTO ON
Install guide 8022 HEAT OOL AUTO ON ustomer Suppt: 888-515-2585 Visit our website www.ritetemp.biz Install guide 8022 aution Tools To avoid electrical shock and to prevent damage to the furnace, air conditioner,
More informationInstall Guide Customer Support: or Visit our website
Install Guide 8095 ustomer Support: 888-515-2585 or Visit our website www.ritetemp.biz Install Guide 8095 aution Tools 1 Location To avoid electrical shock and to prevent damage to the furnace, air conditioner,
More informationInstall guide Caution ENGLISH
OOL OFF HET Install guide 606 aution Your thermostat is a precise instrument, handle it with care. Turn off electricity to the appliance befe installing servicing thermostat any part of the system. Do
More informationInstall Guide Customer Support: or Visit our website
Install Guide 8045 Customer Support: 888-515-2585 or Visit our website www.ritetemp-thermostats.com 312-014 Install Guide 8045 Caution To avoid electrical shock and to prevent damage heating system, and
More informationInstall Guide 8046 ENGLISH. Customer Support: or: visit our website Printed in China ON.
. ON Install Guide 8046. ON ENGLISH Customer Support: 888-515-2585 or: visit our website www.ritetemp-thermostats.com Printed in China 1-405-049 Install Guide 8046 Caution To avoid electrical shock and
More informationInstall Guide CT100. Caution. Caution
PG 1 Install Guide CT100 Caution topcover Turn off electricity to the HVAC system before installing or servicing thermostat or any part of the system. Do not turn electricity back on until work is completed.
More informationInstall Guide CT110. Caution. Caution ENGLISH
Install Guide CT110 Caution Turn off electricity to the HVAC system before installing or servicing thermostat or any part of the system. Do not turn electricity back on until work is completed. Do not
More informationNP100 Non-Programmable Thermostat Installation Instructions & User Guide. For Installation Help. White-Rodgers.com
NP100 Non-Programmable Thermostat Installation Instructions & User Guide For Installation Help 1-877-654-9394 White-Rodgers.com 2011 Printed in hina White-Rodgers 8100 West Florissant Avenue St. Louis,
More informationADC-T2000. Smart Thermostat v1.5
ADC-T2000 ADC-T2000 Smart Thermostat User Product Guide Manual 170308 v1.5 Smart Thermostat Product Manual 1 Before installing or servicing the thermostat, turn off power to the system at the circuit breaker.
More informationOperator: Save these instructions for future use!
HITE-RODERS 1F97-51 7-Day Electronic Digital Thermostat INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use FAILURE TO READ AND FOLLO ALL INSTRUCTIONS CAREFULL BEFORE INSTALLIN OR
More informationInstallation Instructions HEAT COOL FAN POWER
DIGITAL THERMOSTAT Installation Instructions P/N P474-2300RE MULTI-STAGE & PUMP WIRELESS REEIVER Use with most Air onditioning & Heating Systems including: 1 or 2 Stage Electric ooling & Gas Heating, Heat
More informationOperator: Save these instructions for future use!
WHITE-ODES 1F89-11 Non-Programmable Electronic Digital Heat Pump Thermostat INSTALLATION AND OPEATION INSTUTIONS Operator: Save these instructions for future use! FAILUE TO EAD AND FOLLOW ALL INSTUTIONS
More informationFOR BOTH CONVENTIONAL AND HEAT PUMP SYSTEMS INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT!
PSP721U SMART TEMP UNIVERSAL PROGRAMMABLE THERMOSTAT FOR BOTH CONVENTIONAL AND HEAT PUMP SYSTEMS INSTALLATION AND OPERATING INSTRUCTIONS 52033 IMPORTANT! Please read all instructions carefully before beginning
More informationIF79 CAUTION CONTENTS YOUR THERMOSTAT REPLACES 1 PREPARATIONS. Installation Instructions for. Heating & Air Conditioning
CONTENTS Installation Instructions for Heating & Air Conditioning IF79 n- Programmable Heat Pump Thermostat Preparations... 1 Thermostat Details... 1 Removing Old Thermostat... 1-2 Mounting and Wiring...
More informationWiring: All wiring should be conventional 18 gauge thermostat wire. Thermostats and zone dampers may be located up to 300 feet from the Z-300 panel.
THE EEN Z NE Z EE THE NE N Sequence of Operation: The reen Zone Z-300-HPS is a residential / light commercial zone control system that allows a single HVA unit to have up to three separate zones. Each
More informationOperation 8085C ENGLISH. Customer Support: or Visit our webiste Printed in China
Operation 8085C MENU PROGRAM RESET ENGLISH MENU PROGRAM RESET Customer Support: 888-515-2585 or Visit our webiste www.ritetemp-thermostats.com Printed in China 1-402-006 Operation 8085C PG 1 Day Indoor
More informationINSTALLATION MANUAL. Need Help? This manual covers the following models: T705. Power Type. Thermostat Applications Guide. Page.
INSTALLATION MANUAL This manual covers the following models: T705 Thermostat Applications uide Des cription as or Oil Heat Electric Furnace Heat Pump (No Aux. or Emergency Heat) Heat Pump (with Aux. or
More informationProduct Instructions. Viega Programmable Heat/Cool Thermostat. Technical data
Programmable Heat/ool Thermostat The programmable heat/cool thermostat is easy to install, easy to wire, and easy to program. It can be used for single stage heating and cooling applications, making it
More informationSafety & Installation Instructions
Model 8476 Thermostat with Event-Based Air Cleaning Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS Table of contents Installation Installation location recommendations... 3 Outdoor
More informationWHITE-RODGERS 90 SERIES 1F MULTI-STAGE/HEAT PUMP INSTALLATION/CONFIGURATION
INSTALLATION DESCRIPTION WHITE-RODGERS 90 SERIES 1F9-391 MULTI-STAGE/HEAT PUMP INSTALLATION/CONFIGURATION This White-Rodgers Digital Thermostat uses microcomputer technology to provide precise time, humidity,
More informationModel NT20e Installation Guide
Model NT20e Installation Guide Rev 1.4 Page 2 of 14 1. Preparing for Installation CAUTION Do not remove the NT20e from the Electro-static bag until instructed from this installation guide. The NT20e is
More information2 THERMOSTAT DETAILS 3 REMOVING OLD THERMOSTAT
CONTENTS Installation Instructions for Heating & Air Conditioning 1F79 n-programmable Heat Pump Thermostat Preparations... 1 Thermostat Details... 1 Removing Old Thermostat... 1-2 Mounting and Wiring...
More informationINSTALLATION MANUAL. Need Help? This manual covers the following models: T905. Power Type. Thermostat Applications Guide. Page.
INSTALLATION MANUAL This manual covers the following models: T905 Thermostat Applications uide Description as or Oil Heat Electric Furnace Heat Pump (No Aux. or Emergency Heat) Heat Pump (with Aux. or
More informationINSTALLATION MANUAL. Need Help? This manual covers the following models: T805. Power Type. Thermostat Applications Guide. Page.
INSTALLATION MANUAL This manual covers the following models: T805 Thermostat Applications uide Des cription as or Oil Heat Electric Furnace Heat Pump (No Aux. or Emergency Heat) Heat Pump (with Aux. or
More informationSafety & Installation Instructions
8400 Series Thermostats Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS 61000652C 8400 Tstat Install.indd 1 10/13/09 11:08:56 AM Table of contents Installation Installation location
More information1F Non-programmable Electronic Digital Heat Pump Thermostat INSTALLATION AND OPERATION INSTRUCTIONS
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE. DESCRIPTION Your new White-Rodgers Digital Thermostat
More informationT8090A/Q682B Heating, Cooling, and Heating-Cooling Thermostat, Wallplate and Subbase
M75 M75 T8090A/Q68B Heating, ooling, and Heating-ooling Thermostat, allplate and Subbase SUPER TRADELINE Installation Instructions for the Trained Service Technician. Preparation heck thermostat and subbase
More informationSafety & Installation Instructions
8400 Series Thermostats Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS 61000652A 8400 Tstat Install.indd 1 7/23/09 2:20:45 PM Table of contents Installation Installation location recommendations...
More informationTX9000TS SERIES SMART TEMP ELECTRONIC THERMOSTAT. Easy as INSTALLATION AND OPERATING INSTRUCTIONS
SMART TEMP ELECTRONIC THERMOSTAT INSTALLATION AND OPERATIN INSTRUCTIONS Installs Easily Set Day & Time IMPORTANT! Please read all instructions carefully before beginning installation. Save them for future
More informationInstallation Guide ProR221J, ProR212J, ProR321J and ProR312J
ProZone I n t e l l i g e n t Z o n i n g Zones See table below. ompatible Equipment All panels operate with gas/electric systems, conventional heat pumps and dual fuel heat pumps. Equipment Selection
More informationTCONT602AF22MA. Programmable Comfort Control. Installation Instructions 18-HD37D1-1
TCONT602AF22MA Programmable Comfort Control Installation Instructions 18-HD37D1-1 Product Application This Comfort Control provides electronic control of 24 VAC single-stage and multistage heating and
More informationGLAS. Installation Instructions
LAS Installation Instructions Support If at any point you need assistance, we re here to help. Visit www.glas.johnsoncontrols.com/support for how-to videos and frequently asked questions. an t find what
More informationINSTALLATION INSTRUCTIONS FOR MODEL 7330D3351 & 7330D3361 WALL THERMOSTAT
INSTALLATION INSTRUCTIONS FOR MODEL 7330D3351 & 7330D3361 WALL THERMOSTAT APPLICATION These thermostats are designed to operate all R.V. Products ceiling assemblies, which control the air conditioner 115
More information1F Non-Programmable Electronic Digital Multi-Stage Thermostat INSTALLATION AND OPERATION INSTRUCTIONS
1F83-261 Non-Programmable Electronic Digital Multi-Stage Thermostat INSTALLATION AND OPERATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS
More information7-Day. Digital Thermostat. residential. & 2-cool
Digital Thermostat residential THEMOSTAT T1100FS 7-Day POAMMABLE up to 2-heat & 2-cool HEAT OOL HEAT PUMP ontrol up to 2 Heat & 2 ool Stages 7-Day Programmable 4 Settings/Day Auto hangeover 5 minute Built-In
More informationWARNING Important Safety Information
Builder Series Non-Programmable Thermostats MODEL 1000 MODEL 0 1 2 3 4 Single Stage Heat / Cool Conventional and Heat Pump Multi-Stage 2 Heat / 1 Cool Conventional and Heat Pump Before Installing, Programming
More informationOWNERS MANUAL YEAR LIMITED WARRANTY READ ALL INSTRUCTIONS BEFORE PROCEEDING. Store this booklet for future reference
3000 Premier Series Non-Programmable Single Stage /Cool Digital Thermostat OWNERS MANUAL Compatible with low voltage single stage gas, oil or electric heating or cooling systems, including single stage
More informationSC Installation, Operation & Application Guide
SC 1800 Manual Changeover Non-Programmable Hardwired Non-Programmable Electronic Thermostat Controls Single Stage Heating Systems Millivolt and Hydronic (water or steam) System Compatible Compatible with
More informationInstaller Guide. WARNING Important Safety Information. 1 Specifications
1 Specifications cont. Premier Series Universal Auto Changeover Up to 3 Heat / 2 Cool Heat Pump or 2 Heat / 2 Cool Conventional Thermostat Installer Guide Before Installing, Programming or Operating, PLEASE
More informationEmerson Blue Easy Set 1H/1C
Emerson Blue Easy Set 1H/1C Model: 1F86EZ-0251 Non-Programmable Thermostat with 3 Temperature Pre-Sets Home, Sleep and Away Installation Instructions and User Guide Message to Homeowner Congratulations
More informationINSTALLATION INSTRUCTIONS Venstar Inc. 08/07
Digital Thermostat residential THEMOSTAT T1 800 7-DAY POAMMABLE up to 3-heat & 2-cool PUMP ontrol up to 3 Heat & 2 ool Stages 3 onfigurable Outputs Adjustable 2nd & 3rd Stage Timers & Deadbands Backlit
More informationSafety & Installation Instructions
Model 8620 Thermostat with Event-Based Air leaning and Humidity or Ventilation ontrol Safety & Installation Instructions READ AND SAVE THESE INSTRUTIS Table of contents Installation Installation location
More informationNON- INSTALLATION INSTRUCTIONS Venstar Inc. 08/07. Digital Thermostat T2700. commercial. & 2-cool. up to 2-heat PROGRAMMABLE
Digital Thermostat commercial THEMOSTAT T2700 NON- POAMMABLE up to 2-heat & 2-cool PUMP ontrol up to 3 Heat & 2 ool Stages 3 onfigurable Outputs Backlit Display & Button Legends Aux Heat Indicator Dry
More information2 THERMOSTAT DETAILS 3 REMOVING OLD THERMOSTAT
CONTENTS Installation Instructions for Heating & Air Conditioning 1F72 5/2 Day Programmable Heat Pump Thermostat Preparations... 1 Thermostat Details... 1 Removing Old Thermostat... 1-2 Mounting and Wiring...
More informationOperator: Save these instructions for future use!
WHITE-RODGERS 1F83-51 Non-Programmable Electronic Digital Multi-Stage Thermostat INSTALLATION AND OPERATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL
More informationINSTALLATION INSTRUCTIONS FAN COIL PROGRAMMABLE DIGITAL THERMOSTAT. Meets California Title 24
INSTALLATION INSTUTIONS FAN OIL POAMMABLE DIITAL THEMOSTAT Meets alifornia Title 24 P/N E055-71520302 P/N E055-71520305 72 74 Am I2:00 Mo OOL AUTO HEAT 70 2- O 4-PIPE POAMMABLE Auto-hangeover is available
More informationInstaller Guide. WARNING Important Safety Information. 1 Specifications
1 Specifications cont. Premier Series Universal Auto Changeover Up to 3 Heat / 2 Cool Conventional and Heat Pump Thermostat Installer Guide Before Installing, Programming or Operating, PLEASE READ ALL
More informationPS4000 and PS5000 Touchscreen Programmable Thermostat Installation and Owners Manual Robertshaw 01/
PS4000 and PS5000 Touchscreen Programmable Thermostat Installation and Owners Manual www.robertshaw.com 2016 Robertshaw 01/16 352-00244-001 IMPORTANT SAFETY INFORMATION WARNING: ELECTRICAL SHOCK HAZARD
More informationHEAT HEAT HEAT COOL COOL
INSTALLATION INSTUTIONS OMMEIAL THEMOSTAT P/N P374-2800 I 2 : 0 0 Su AUTO Pm 74 OOL 7 2 HEAT T O T A L I N E HEAT OOL 7-DAY HEAT PUMP POAMMABLE DIITAL THEMOSTAT 3 onfigurable Outputs ontrol up to 2 ool
More informationTP-S-855C. Installation Tips. Installation Manual. Installation Tips. Installation Tips
Installation Manual Vive omfort P.O. Box 3377 Springfield, MO 65804 Toll Free : 888-776-47 Web: www.vivecomfort.com Hours of Operation: M-F 9AM - 6PM Eastern Thermostat Application uide Description as
More informationOperator: Save these instructions for future use!
WHITE-RODGERS 1F81-51 Programmable Electronic Digital Multi-stage Thermostat INSTALLATION AND OPERATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS
More informationHow to install your ecobee4
How to install your ecobee4 Be happy You have joined a growing community of people who want to conserve energy, save money, and do something good for our planet. Let s get started! Download the ecobee
More informationOWNERS MANUAL YEAR LIMITED WARRANTY READ ALL INSTRUCTIONS BEFORE PROCEEDING. Store this booklet for future reference
3100 Premier Series Non-Programmable 2 Heat / 2Cool & Heat / Cool Digital Thermostat OWNERS MANUAL Compatible with low voltage multi-stage heat / cool systems with up to two stages of heating and two stages
More informationWARNING Important Safety Information
1 Specifications Premier Series Non-Programmable Thermostats MODEL 3000 MODEL 3200 1 2 3 4 5 Specifications Installation Testing Your New Thermostat Programming User Settings Temperature Adjustment WARNING
More informationACONT600AF11MA Programmable Comfort Control
ACONT600AF11MA Programmable Comfort Control Installation Instructions Pub. No. 11-HD02D10-4 69-1832-03 Product Application This Comfort Control provides electronic control of 24 VAC single-stage heating
More informationOperator: Save these instructions for future use!
HITE-RDERS 1F80-24 Programmable Electronic Digital Thermostat INSTALLATIN AND PERATIN INSTRUCTINS perator: Save these instructions for future use! FAILURE T READ AND FLL ALL INSTRUCTINS CAREFULL EFRE INSTALLIN
More informationP200 Programmable Thermostat Installation Instructions & User Guide. For Installation Help. White-Rodgers.com
P200 Programmable Thermostat Installation Instructions & User Guide For Installation Help 1-877-654-9394 White-Rodgers.com 2011 Printed in China White-Rodgers 8100 West Florissant Avenue St. Louis, MO
More informationPROGRAMMABLE THERMOSTAT
RAMMABLE THERMOSTAT ! PLEASE TAKE A TIIME TO READ THE INSTRUCTII IONS FIRST.. This thermostat has been designed to provide you with years of trouble free service. Proper understanding of any product is
More informationDetailed Installer Guide
Non-Programmable Thermostats 1020 1220 Single Stage Heat / Cool Conventional and Heat Pump Detailed Installer Guide Up to 2 Heat / 2 Cool Conventional and Heat Pump Model number is located on back of thermostat
More informationWARNING Important Safety Information
1 Specifications Premier Series Non-Programmable Thermostats MODEL 3000 MODEL 3200 1 2 3 4 Specifications Installation Testing Your New Thermostat Programming User Settings WARNING Important Safety Information
More informationIF78 CAUTION CONTENTS YOUR THERMOSTAT REPLACES PREPARATIONS. Installation Instructions for. Heating & Air Conditioning. Non-Programmable Thermostat
CNTENTS Installation Instructions for Heating & Air Conditioning IF78 n-programmable Thermostat Preparations... 1 Thermostat Details... 1 Removing ld Thermostat... 1 Mounting and iring... 2 Check Thermostat
More informationYour LUX/GEO internet connected thermostat puts the control of your comfort in your hands and you are only 10 easy steps away from completion.
EO WiFi THEMOSTAT Welcome to your LUX/EO quick-start guide our LUX/EO internet connected thermostat puts the control of your comfort in your hands and you are only 10 easy steps away from completion. IF
More informationUSER MANUAL WARNING! CONTENTS MODEL SPECIFICATIONS READ ALL INSTRUCTIONS BEFORE PROCEEDING
MODEL Premier Series 3000 USER MANUAL Non-Programmable Single Stage Heat/Cool Digital Thermostat Compatible with low voltage single stage gas, oil or electric heating or cooling systems, including single
More informationProliphix Thermostat Installation Guide. Release 2.0
Proliphix Thermostat Installation Guide Release 2.0 July 2006 Beta Draft Confidential Technical Support When contacting Proliphix for technical assistance, please have the following information available:
More informationTP-S-855i MENU AUTO HEAT. Installation Tips. Installation Manual. Installation Tips. Installation Tips. Hardwire - 24 VAC Common Wire
Installation Manual Vive omfort P.O. Box 3377 Springfield, MO 65804 Toll Free : 888-776-47 Web: www.vivecomfort.com Hours of Operation: M-F 9AM - 6PM Eastern Thermostat Application uide Description as
More informationSafety & Installation Instructions
Home omfort ontrol Model 8910 READ AND SAVE THESE INSTRUTIS Safety & Installation Instructions Table of contents Installation Thermostat installation location recommendations.. 2 Thermostat mounting...
More informationIndicates incorrect room temperature. No second stage or AUX heating. Emergency heat does not turn on
Troubleshooting Poor Temperature Regulation This page lists problems that may affect the temperature performance of your LUX thermostat with suggested resolutions. For more detailed information please
More informationPSPA711/PSPA _PSPA711_722_MAN_ENG5.qxd 2/8/05 9:45 AM Page 2 1 COMPATIBILITY 3 ELECTRICAL RATINGS 2 FEATURES
14165_PSPA711_722_MAN_ENG5.qxd 2/8/05 9:45 AM Page 2 PSPA711/PSPA722 2 UP DOWN 1 COMPATIBILITY Temperature Offset (User Calibration) Your PSPA711 or PSPA722 is compatible with most 24 System or Battery
More informationSafety & Installation Instructions
Model 8800 Universal Communicating Thermostat Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS Table of contents Installation Installation location recommendations... 2 Thermostat mounting...
More informationDIGITAL THERMOSTAT. I2:00 Su AUTO OPTIONAL HUMIDITY MODULE
INSTALLATION INSTUTIONS OMMEIAL THEMOSTAT P/N 33S450-01 7-DAY POAMMABLE DIITAL THEMOSTAT HEAT OOL&HEAT PUMP 3 onfigurable Outputs ontrol up to 3 Heat & 2 ool Stages Adjustable 2nd & 3rd Stage Timers &
More information1F Non-Programmable Electronic Digital Thermostat INSTALLATION AND OPERATION INSTRUCTIONS
FAILURE T READ AND FLL ALL INSTRUCTINS CAREFULL EFRE INSTALLIN R PERATIN THIS CNTRL CULD CAUSE PERSNAL INJUR AND/R PRPERT DAMAE. DESCRIPTIN our new hite-rodgers Digital Thermostat uses the technology of
More informationT8112 Programmable Thermostat
T8112 Programmable Thermostat FEATUES PODUCT DATA HEAT-OFF-COOL system switch. AUTO-ON fan switch. Separate programs for weekdays and weekends (5 day/2 day). Digital LCD display. Easy to program and install.
More informationHoneywell CT3550 PROGRAMMABLE THERMOSTAT. Table of Contents OWNER S GUIDE
Weekday, Saturday and Sunday Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Wallplate Model CT3550 Honeywell CT3550 PROGRAMMABLE THERMOSTAT OWNER S GUIDE Para pedir estas instrucciones
More information1 PREPARATIONS 2 THERMOSTAT DETAILS 3 REMOVING OLD THERMOSTAT. 1E78 Non-Programmable Thermostat CONTENTS
CNTENTS Installation Instructions for Heating & Air Conditioning 1E78 Non-Programmable Thermostat Preparations... 1 Thermostat Details... 1 Removing ld Thermostat... 1 Mounting and iring... 2 Check Thermostat
More informationATP21W02 CONTENTS YOUR THERMOSTAT REPLACES 1 PREPARATIONS REMOVING OLD THERMOSTAT 2 THERMOSTAT DETAILS
CONTENTS Installation Instructions for 97B0082N07 Heating & Air Conditioning 5/2 Day Programmable Heat Pump Thermostat Preparations...1 Thermostat Details...1 Removing Old Thermostat... 1-2 Mounting and
More informationWARNING Important Safety Information
Builder Series Non-Programmable Thermostat MODEL 00NC Heat Only or Cool Only Thermostat Before Installing, Programming or Operating, PLEASE READ ALL INSTRUCTIONS Specifications Temperature Adjustment WARNING
More informationDesign & Installation for. Zonex Systems. System Zone Auto Changeover. System Zone Manual Changeover
Design & Installation for Zonex Systems System 2000 2-20 Zone Auto hangeover System 1000 2-7 Zone Manual hangeover Part #101ASIM ev. September 2003 TABLE OF ONTENTS System 2000 System Operation...1 omponents...1
More information5+2 Day. up to HEAT COOL
Digital Thermostat residential THEMOSTAT T1050 5+2 Day POGAMMABLE up to 2-heat & 2-cool HEAT COOL HEAT PUMP Control up to 2 heat & 2 Cool Stages 4 Settings Per Day Self-prompting programming Auto changeover
More informationheat (2 heat/1 cool).
Product Application This thermostat provides electronic control of 24 VAC heat pump systems with auxiliary heat (2 heat/1 cool). Power Type * Battery power, ColTIll3On wire " CoITI1TIon wire with battery
More informationHeat Link. Stat Link Technical Guide. Fourth Version
Stat Technical Guide Fourth Version Table of ontents About Us...3 Stat System omponents... Thermostatic Zones Defined...6 ol-coded iring Schemes...7 Stat ire to onventional ire Adapter...7 Technical Data
More informationSmart Si Thermostat. Installation Manual
Smart Si Thermostat Installation Manual ONTENTS ETTIN STARTED 1 Welcome 1 Technical Support 1 Before You Begin 2 HVA System ompatibility Information 3 Approvals 4 F ompliance Statement 4 Specifications
More informationT855S 5:23. Installation Manual. Installation Tips. Installation Tips. Installation Tips
Installation Manual Pro Technologies S. lenstone Ave., Suite -00 Springfield, MO 65804 Toll Free: 888-776-47 Web: www.proiaq.com Hours of Operation: M-F 9AM - 6PM Eastern Thermostat Application uide Description
More informationNon-Programmable Digital Thermostat
OWNER'S MANUAL MODEL P474-0140 Non-Programmable Digital Thermostat HEAT PUMP THERMOSTAT 2 HEAT, 1 COOL emergency aux. heat normal energy save Fan On Fan Auto Millivolt Compatible Battery or System Powered
More informationT8034C Heating/Cooling Thermostats
T8034C Heating/Cooling Thermostats INSTALLATI INSTUCTIS APPLICATI These T8034C Thermostats control 4 to 30 Vac singlestage heating-cooling systems. An spdt mercury switch makes (H) to on temperature fall
More informationT8190A/191108AJ Heating or Cooling Thermostat/Wallplate; T8190A/Q682B Heating/Cooling Thermostat/Subbase
M3375 M3375 T890A/908AJ Heating or Cooling Thermostat/Wallplate; T890A/Q68B Heating/Cooling Thermostat/Subbase Installation Instructions for the Trained Service Technician. Preparation NOTE: Order Q68B
More informationSmart Hub THERMOSTAT. Installation Manual
Smart Hub THERMOSTAT Installation Manual Thank you for inviting KONOz into your home. The setup process is easy. All you need to do is follow these simple steps and you ll be on your way to saving energy
More information7-DAY or 5/2-DAY PROGRAMMABLE, OR NON-PROGRAMMABLE THERMOSTAT INSTALLATION AND OPERATING INSTRUCTIONS
TX100E 7-DAY or 5/2-DAY PROGRAMMABLE, OR NON-PROGRAMMABLE THERMOSTAT INSTALLATION AND OPERATING INSTRUCTIONS 52203 IMPORTANT! Please read all of these instructions carefully before beginning installation.
More informationT8132C Programmable Thermostats
T832 Programmable Thermostats pplication The T832 Programmable Thermostat provides energy savings for heating and cooling applications. Separate programs can be set for weekdays and weekends. heck Table
More informationCT2800 Programmable Thermostat
CT2800 Programmable Thermostat INSTALLATION AND PROGRAMMING INSTRUCTIONS Welcome to the world of comfort and energy savings with your new Honeywell Programmable Thermostat. Your new thermostat will automatically
More informationInstallation, Specification & Operation Guide HI TEMP LO TEMP SUPPLY I88. ecojay. SmartZone RESET GND HEAT PUMP GAS/ELECT RVS. VLV.
00 ma SMAT LINK DAMPE DAMPE DAMPE or FA DAMPE POE -X & X Installation, Specification & Operation uide p. p. p. p. FULL US DIITAL DISPLA SPAE FUSE INLUDED QUIK SELESS TEMINALS O AS/ELETI THEMO EXLUSIVE
More information! WARNING. McDonnell & Miller Installation & Maintenance Instructions MM-226(A) Series 69 Low Water Cut-Offs For Steam Boilers
Series Low Water Cut-Offs F Steam Boilers Applications: F residential and commercial boilers of any steaming capacity. McDonnell & Miller Installation & Maintenance Instructions MM-6(A) Series WARIG CAUTIO!
More informationThis thermostat provides electronic control of 24 VAC single-stage and multi-stage
Product Application This thermostat provides electronic control of 24 VAC single-stage and multi-stage heating and cooling systems, or 750 mv heating systems. System Types (up to 2 heat/2 cool) (ats, oil,
More informationProgrammable 5-2 Day Digital Thermostat
P/N TSTAT0712 Programmable 5-2 Day Digital Thermostat 1 STAGE HEAT COOL THERMOSTAT SINGLE STAGE HEAT PUMP COMPATILE (Does not control auxiliary heat) Separate rams for weekdays & weekends Large, easy to
More informationOWNERS MANUAL YEAR LIMITED WARRANTY READ ALL INSTRUCTIONS BEFORE PROCEEDING. Store this booklet for future reference
5100 Premier Series 7-Day Programmable 2-Heat / 2-Cool Heat /Cool Digital Thermostat OWNERS MANUAL Compatible with low voltage multi-stage heat / cool systems with up to two stages of heating and two stages
More informationMagicStat CT3300 Programmable Thermostat
MagicStat CT3300 Programmable Thermostat Installation and Programming Instructions Weekday/Weekend (5-day/2-day) Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Mounting Plate Model
More informationThe model numbers of 3-way refrigerators include.3. The model numbers of 2-way refrigerators
Installation Manual F N62X and N62XXX models: F N64X and N64XXX models: F N64XIM and N64XIMXX models: F N82X and N82XXX models: F N84X and N84XXX models: F N84XIM and N84XIMXX models: 6 cu.ft., 2way, R.V.
More informationUSER MANUAL MODEL READ ALL INSTRUCTIONS BEFORE PROCEEDING. 5-2 Day Programmable Multi-Stage 2 Heat/1 Cool Heat Pump Digital Thermostat
WARNING! Important Safety Information Builder MODEL 2200 Series 5-2 Day Programmable Multi-Stage 2 Heat/1 Cool Heat Pump Digital Thermostat USER MANUAL Compatible with low voltage multi stage heat/cool
More informationOperator: Save these instructions for future use!
WHITE-RODGERS 1F82-51 Programmable Electronic Digital Heat Pump Thermostat INSTALLATION AND OPERATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS
More information