Technical Support Division GD CHIGO HEATING & VENTILATION EQUIPMENT CO., LTD.

Transcription

1 Technical Support Division

2 New CMV System - Floor ceiling Indoor Unit 1 1. External appearance 2. Nomenclature 3. Specifications 4. Dimensions 5. Service space 6. Piping diagram 7. Wiring diagram 8. Capacity tables 9. Electric characteristics 10. Sound pressure levels 11. Accessories 12. Exploded view

3 2 1. External appearance New CMV System - Floor ceiling Indoor Unit 2. Nomenclature CMV - D 160 LD / H N R1 - B Design code B: 2nd generation Refrigerant type R1: R410A Power code N: 208~230V/1PH/60Hz Omit: 220~240V/1PH/50Hz Function code H: Heat pump Indoor unit code Q: 4-way cassette G: Wall-mounted TA: Low ESP ducted TB: Medium ESP ducted TH: High ESP ducted LD: Floor ceiling TF: Full fresh air processor Capacity (*100W) DC Fan motor Chigo VRF system

4 New CMV System - Floor ceiling Indoor Unit 3. Specifications 3 Model CMV-D45LD/HR1-B CMV-D56LD/HR1-B CMV-D71LD/HR1-B Power supply V/1PH/50Hz V/1PH/50Hz V/1PH/50Hz Capacity Cooling kw Heating kw Power Input kw Model DR LD-8 DR LD-8 DR LD-8 Fan motor Type DC DC DC Brand Panasonic Panasonic Panasonic Indoor coil Speed (Hi/Med/Low) r/min 800/650/ /650/ /880/780 Number of rows Fin type Hydrophilic aluminum Hydrophilic aluminum Hydrophilic aluminum Tube diameter and type mm Ø9.53,Innergroove tube Ø9.52,Innergroove tube Ø9.52,Innergroove tube Air flow (High speed) m 3 /h Sound power level db(a) 37~46 37~46 39~48 Body Dimension (W H D) mm Packing (W H D) mm Net/Gross weight kg 36/42 36/42 36/42 Refrigerant type R410A R410A R410A Throttle type EXV EXV EXV Design pressure MPa Liquid pipe / Gas pipe mm Ø6.35/ Ø12.7 Ø6.35/ Ø12.7 Ø9.53/ Ø15.88 Connecting wire Power wire mm 2 2.5*3 2.5*3 2.5*3 Signal wire mm *2 0.75*2 0.75*2 Drainage water pipe (Outer diameter) mm Ø20 Ø20 Ø25 Controller Standard Remote controller Remote controller Remote controller Optional Wired controller Wired controller Wired controller Operation temp C 16~32 16~32 16~32 Notes: 1) Nominal cooling capacities are based on the following conditions. Outdoor temperature: 35 C DB Return air temperature: 27 C DB, 19 C WB Equivalent piping length: 8m in horizontal 2) Nominal heating capacities are based on the following condition. Outdoor temperature: 7 C DB, 6 C WB Return air temperature: 20 C DB Equivalent piping length: 8m in horizontal 3) Sound pressure level: Semi-anechoic chamber conversion value, measured at a point 1 m in front of the unit at a height of 1.4 m. 4) The above data may be changed without notice for future improvement on quality and performance.

5 4 New CMV System - Floor ceiling Indoor Unit Model CMV-D80LD/HR1-B CMV-D90LD/HR1-B CMV-D112LD/HR1-B Power supply V/1PH/50Hz V/1PH/50Hz V/1PH/50Hz Capacity Cooling kw Heating kw Power Input kw Model DR LD-8 DR LD-8 2*DR LD-8 Fan motor Type DC DC DC Brand Panasonic Panasonic Panasonic Indoor coil Speed (Hi/Med/Low) r/min 980/880/ /1200/ /1150/1000 Number of rows Fin type Hydrophilic aluminum Hydrophilic aluminum Hydrophilic aluminum Tube diameter and type mm Ø9.53,Innergroove tube Ø9.53,Innergroove tube Ø9.53,Innergroove tube Air flow (High speed) m 3 /h Sound power level db(a) 39~48 44~50 45~52 Body Dimension (W H D) mm Packing (W H D) mm Net/Gross weight kg 36/42 38/44 51/58 Refrigerant type R410A R410A R410A Throttle type EXV EXV EXV Design pressure MPa Liquid pipe / Gas pipe mm Ø9.53/ Ø15.88 Ø9.53/ Ø15.88 Ø9.53/ Ø15.88 Connecting wire Power wire mm 2 2.5*3 2.5*3 2.5*3 Signal wire mm *2 0.75*2 0.75*2 Drainage water pipe (Outer diameter) mm Ø25 Ø25 Ø25 Controller Standard Remote controller Remote controller Remote controller Optional Wired controller Wired controller Wired controller Operation temp C 16~32 16~32 16~32 Notes: 1) Nominal cooling capacities are based on the following conditions. Outdoor temperature: 35 C DB Return air temperature: 27 C DB, 19 C WB Equivalent piping length: 8m in horizontal 2) Nominal heating capacities are based on the following condition. Outdoor temperature: 7 C DB, 6 C WB Return air temperature: 20 C DB Equivalent piping length: 8m in horizontal 3) Sound pressure level: Semi-anechoic chamber conversion value, measured at a point 1 m in front of the unit at a height of 1.4 m. 4) The above data may be changed without notice for future improvement on quality and performance.

6 New CMV System - Floor ceiling Indoor Unit 5 Model CMV-D140LD/HR1-B CMV-D160LD/HR1-B Power supply V/1PH/50Hz V/1PH/50Hz Capacity Cooling kw Heating kw Power Input kw Model 2*DR LD-8 2*DR LD-8 Fan motor Type DC DC Brand Panasonic Panasonic Indoor coil Speed (Hi/Med/Low) r/min 1300/1150/ /1150/1000 Number of rows 2 2 Fin type Hydrophilic aluminum Hydrophilic aluminum Tube diameter and type mm Ø9.53,Innergroove tube Ø9.53,Innergroove tube Air flow (High speed) m 3 /h Sound power level db(a) 45~52 45~52 Body Dimension (W H D) mm Packing (W H D) mm Net/Gross weight kg 51/58 51/58 Refrigerant type R410A R410A Throttle type EXV EXV Design pressure MPa Liquid pipe / Gas pipe mm Ø9.53/ Ø15.9 Ø9.53/ Ø15.9 Connecting wire Power wire mm 2 2.5*3 2.5*3 Signal wire mm *2 0.75*2 Drainage water pipe (Outer diameter) mm Ø25 Ø25 Controller Standard Remote controller Remote controller Optional Wired controller Wired controller Operation temp C 16~32 16~32 Notes: 1) Nominal cooling capacities are based on the following conditions. Outdoor temperature: 35 C DB Return air temperature: 27 C DB, 19 C WB Equivalent piping length: 8m in horizontal 2) Nominal heating capacities are based on the following condition. Outdoor temperature: 7 C DB, 6 C WB Return air temperature: 20 C DB Equivalent piping length: 8m in horizontal 3) Sound pressure level: Semi-anechoic chamber conversion value, measured at a point 1 m in front of the unit at a height of 1.4 m. 4) The above data may be changed without notice for future improvement on quality and performance.

7 6 4. Dimensions New CMV System - Floor ceiling Indoor Unit A B D C E F Holder Holder Model Body dimension (mm) Installation dimension (mm) A B C D E F CMV-V45LD/HR1-B CMV-V56LD/HR1-B CMV-V71LD/HR1-B CMV-V80LD/HR1-B CMV-V90LD/HR1-B CMV-V112LD/HR1-B CMV-V140LD/HR1-B CMV-V160LD/HR1-B

8 New CMV System - Floor ceiling Indoor Unit 5. Service space There is enough room for installation and maintenance. The ceiling is horizontal, and its structure can endure the weight of the indoor unit. The outlet and the inlet are not impeded, and the influence of external air is the least. The air flow can reach throughout the room. The connecting pipe and drainpipe could be extracted out easily. There is no direct radiation from heaters. 7 >20mm >20mm Install on the floor >600mm Install on the ceiling >600mm >600mm >600mm

9 8 6. Piping diagram New CMV System - Floor ceiling Indoor Unit Flare nut Liquid side Flare nut Liquid side Indoor unit EXV T2 T2B Motor Heat exchanger T1 Notes: 1) T1: Room temperature sensor 2) T2: Temperature sensor of middle heat exchanger 3) T2B: Temperature sensor of heat exchanger outlet 4) EXV: Electrical expansion valve

10 CN3 5 SW2 SW New CMV System - Floor ceiling Indoor Unit 7. Wiring diagram 7.1 Wiring diagram 9 Notes: 1) Color code: RD: Red OR: Orange BK: Black: BR: Brown WH: White PT1 T2B PT2 PT3 T2 T1 CN17 ALARM CN1 PUMP PUMP CN2 RD PTC L CN10 BK N 2) T1: Room temperature sensor 3) T2: Temperature sensor of middle heat exchanger 4) T2B: Temperature sensor of heat exchanger outlet Receive and display light board F01 SW1 LEFT FAN CN7 RIGHT FAN CN8 CN26 REMO_CTRL E21 Controller WATER SWITCH CN4 HEATER IC2 T1 RY4 IC4 C10 10 CN18 CN27 Wire control Water-SW CN23 Duct display EXV CN16 5 DC FAN1 CN29 CN30 OUT SWING IN SWING CN31 5) EXV: Electrical expansion valve 6) Electrical heater is optional, please contact to Chigo s technician for the detail. 5 DC FAN2

11 10 New CMV System - Floor ceiling Indoor Unit Chigo VRF indoor unit connect with card key Connect the remote control terminal on the indoor PCB to the hotel card module. NOTE: The terminal in the hotel card module must be a switch without any voltage/current input to the PCB, otherwise the PCB will be broken.

12 New CMV System - Floor ceiling Indoor Unit 7.2 Dial switches SW1: Capacity switch. Different number in the switch indicates different capacity. It is set in factory; leave it as default setting, 11 HP Capacity (kw) 1.8/ /2.6/ /3.5/ /4.5/ / /6.6/7.1 Code HP Capacity (kw) / /11.0/ /12.5/ /16.0 Code DP SW Name Switch number 1 of SW3 Switch number 4 of SW3 Switch number 2,3 of SW3 Function Auto-restart when power failure switch. / status, operation mode, fan speed, temperature, swing, remote control locked will be recovered. Indoor unit address elimination DP Reserved DP DP DP Dial up to disable Auto-restart function Dial up to erase indoor unit s address. Default setting Setting DP Dial down to enable Auto-restart function (Default setting) DP DP Default setting

13 SW2, only available in heating mode. Name Switch number 1,2 of SW2 New CMV System - Floor ceiling Indoor Unit Function Reserved Setting Default setting Name Switch number 3,4 of SW2 Function Heating temperature compensation value selection. When temperature difference between setting temperature and room temperature is higher than the setting value, indoor fan motor turns off. DO NOT change the default setting without professional guidance. 6 C Default setting 2 C Setting 4 C 8 C

14 New CMV System - Floor ceiling Indoor Unit 13 Name Switch number 5,6 of SW2 Function Temperature selection of turning off fan motor in anti-cold-wind-blow mode. When indoor heat exchanger temperature is lower than the setting value, indoor fan motor turns off. DO NOT change the default setting without professional guidance. 15 C Default setting 20 C Setting 24 C 26 C

15 14 Name Function Switch number 7,8 of SW2 New CMV System - Floor ceiling Indoor Unit Indoor fan motor stopping gap selection in heating mode. When room temperature gets to (set point + temperature value in Switch number 3,4 of SW2), at this moment indoor unit capacity requirement is 0, indoor fan motor turns off for 4 minutes ( this stopping duration time can be changed by below setting). After that indoor fan will run in low speed for 1 minute (this timing is fixed), if indoor unit capacity requirement is still 0, then indoor fan motor keeps off for 4 minutes, and then cycles. DO NOT change the default setting without professional guidance. 4 minutes Default setting 8 minutes Setting 12 minutes 16 minutes SW8, reserved, leave it as default setting (both switches dial down).

16 New CMV System - Floor ceiling Indoor Unit 8 Capacity tables 8.1 Cooling capacity (kw) TC: Total Capacity SC: Sensible Capacity WB: Wet-bulb Temperature DB: Dry-bulb Temperature Indoor temperature ( C WB/DB) Outdoor 14/20 16/23 18/26 19/27 20/28 22/30 24/32 temperature ( C DB) TC SC TC SC TC SC TC SC TC SC TC SC TC SC kw kw kw kw kw kw kw kw kw kw kw kw kw kw

17 16 New CMV System - Floor ceiling Indoor Unit capacity (kw) TC: Total Capacity SC: Sensible Capacity WB: Wet-bulb Temperature DB: Dry-bulb Temperature Indoor temperature ( C WB/DB) Outdoor 14/20 16/23 18/26 19/27 20/28 22/30 24/32 temperature ( C DB) TC SC TC SC TC SC TC SC TC SC TC SC TC SC kw kw kw kw kw kw kw kw kw kw kw kw kw kw

18 New CMV System - Floor ceiling Indoor Unit 17 capacity (kw) TC: Total Capacity SC: Sensible Capacity WB: Wet-bulb Temperature DB: Dry-bulb Temperature Indoor temperature ( C WB/DB) Outdoor 14/20 16/23 18/26 19/27 20/28 22/30 24/32 temperature ( C DB) TC SC TC SC TC SC TC SC TC SC TC SC TC SC kw kw kw kw kw kw kw kw kw kw kw kw kw kw

19 Heating Capacity (kw) New CMV System - Floor ceiling Indoor Unit TC: Total Capacity WB: Wet-bulb Temperature DB: Dry-bulb Temperature Indoor temperature ( C DB) Outdoor temperature ( C) TC TC TC TC TC TC WB DB kw kw kw kw kw kw

20 New CMV System - Floor ceiling Indoor Unit 19 Capacity (kw) TC: Total Capacity WB: Wet-bulb Temperature DB: Dry-bulb Temperature Indoor temperature ( C DB) Outdoor temperature ( C) TC TC TC TC TC TC WB DB kw kw kw kw kw kw

21 20 New CMV System - Floor ceiling Indoor Unit Capacity (kw) TC: Total Capacity WB: Wet-bulb Temperature DB: Dry-bulb Temperature Indoor temperature ( C DB) Outdoor temperature ( C) TC TC TC TC TC TC WB DB kw kw kw kw kw kw

22 New CMV System - Floor ceiling Indoor Unit 21 9 Electrical characteristics Model Indoor unit Power cable MFC Hz Voltage Minimum Maximum L 20m L 50m Grounded Signal cable CMV-D45LD/HR1-B 50Hz V *2.5mm 2 2*4.0mm 2 2.5mm 2 2*0.75 mm 2 CMV-D56LD/HR1-B 50Hz V *2.5mm 2 2*4.0mm 2 2.5mm 2 2*0.75 mm 2 CMV-D71LD/HR1-B 50Hz V *2.5mm 2 2*4.0mm 2 2.5mm 2 2*0.75 mm 2 CMV-D80LD/HR1-B 50Hz V *2.5mm 2 2*4.0mm 2 2.5mm 2 2*0.75 mm 2 CMV-D90LD/HR1-B 50Hz V *2.5mm 2 2*4.0mm 2 2.5mm 2 2*0.75 mm 2 CMV-D112LD/HR1-B 50Hz V *2.5mm 2 2*4.0mm 2 2.5mm 2 2*0.75 mm 2 CMV-D140LD/HR1-B 50Hz V *2.5mm 2 2*4.0mm 2 2.5mm 2 2*0.75 mm 2 CMV-D160LD/HR1-B 50Hz V *2.5mm 2 2*4.0mm 2 2.5mm 2 2*0.75 mm 2 Notes: 1) Minimum: Permitted minimum operating voltage, lower than this value may damage the system 2) Maximum: Permitted maximum operating voltage, higher than this value may damage the system 3) MC: Minimum Current (A) 4) MFC: Maximum Fuse Current (A) 5) L: Total length of cable (m)

23 22 10 Sound levels 10.1 Test condition New CMV System - Floor ceiling Indoor Unit 1 m 1 m Microphone 0.8 m 1.5 m Microphone Notes: Semi-anechoic chamber conversion value, measured at a point 1m in front of the unit at a height of 1.5m 10.2 Test data (Sound pressure level) Model Sound pressure level (db(a)) High speed Medium speed Low speed CMV-D45LD/HR1-B CMV-D56LD/HR1-B CMV-D71LD/HR1-B CMV-D80LD/HR1-B CMV-D90LD/HR1-B CMV-D112LD/HR1-B CMV-D140LD/HR1-B CMV-D160LD/HR1-B Notes: During actual operation, these values are normally somewhat higher as a result of ambient conditions.

24 New CMV System - Floor ceiling Indoor Unit 11 Accessories 11.1 Standard accessories. 23 Item Quantity Shape Usage Installation manual for indoor unit 1 / Must deliver to customer Insulation sheath 2 Thermal insulation for the jointing part of piping Cover board 1 For stopping small animal getting into the unit Hexagonal head bolt 4 For installation use Round shape insulation termination points U shape insulation termination points 6 For wiring 3 For wiring Remote controller 1 For controlling indoor unit Batteries 2 Power to remote controller Left and right hanging holder 2 For hanging indoor unit Nuts, flat gaskets, spring gaskets 4 For hanging indoor unit Drainage connection pipe 1 For connecting draining condensate water pipe to indoor unit Bag 4 For bagging accessories 11.2 Local buy accessories. Specification Item 4.5kW~5.6kW 7.1kW~8.0kW 9.0kW~16.0kW Liquid side copper pipe Ø6.35mm*0.75mm Ø9.53mm*0.75mm Gas side copper pipe Ø12.7mm*0.75mm Ø15.9mm*1.0mm Ø15.9mm*1.0mm Drainage pipe PVC Pipe insulation Thickness 10mm Power cables 2*2.5 mm 2 (When total cable length is 20m) 2*4.0 mm 2 (When total cable length is 50m) Grounded cable 2.5 mm 2 Signal cables 2*0.75 mm 2 (AVP, RVP, RVVP)

25 24 12 Exploded view New CMV System - Floor ceiling Indoor Unit CMV-V45LD/HR1-B, CMV-V56LD/HR1-B, CMV-V71LD/HR1-B, CMV-V80LD/HR1-B, CMV-V90LD/HR1-B No. Part name Quantity No. Part name Quantity 1 Rear cover 1 18 Right mounting plate of evaporator 1 2 Chassis assembly 1 19 Right cover 1 3 E-part box cover 1 20 Right seal plate 1 4 E-part box mat 1 21 Right separating board 1 5 Indoor PCB assembly 1 22 Evaporator component E-part box Left mounting plate of evaporator Indoor PCB Shunt capillary assembly Fan capacitor Air inlet header pipe assembly of evaporator Transformer Evaporator assembly Terminal Right mounting plate of evaporator 1 6 Left seal plate 1 23 Air-out frame component 1 7 Left cover Fixing board assembly for air-out frame 1 8 Left hoisting pate Display film 1 9 Left separating board Ⅰ Display lamp panel 1 10 Motor separating board Vertical step motor 1 11 Wheel volute for slim type Horizontal step motor 1 12 Indoor fan motor Endbearing of louver 2 13 Air inlet grille Intermediate bearing of louver 8 14 Top Cover assembly Guard vane Weld assembly of Water drain pan 1 24 Upper horizontal louver Water outlet rubber cover 1 25 Down horizontal louver 1 16 Supporting board for motor 1 26 EXV supporting board 1 17 Intermediate transverse girder weld assembly 1 18 Right mounting plate of evaporator 1

26 New CMV System - Floor ceiling Indoor Unit CMV-V112LD/HR1-B, CMV-V140LD/HR1-B, CMV-V160LD/HR1-B 25 No. Part name Quantity No. Part name Quantity 1 Right cover 1 16 Top Cover assembly 1 2 Left cover 1 17 Electric box cover 1 3 Right seal plate 1 18 E-parts assy 1 4 Left seal plate Electric box 1 5 Right hoisting plate Indoor PCB 1 6 Left hoisting pate Fan capacitor 2 7 Rat guard Temperature sensors(indoor ) 1 8 Handle Temperature sensors (evaporator ) 1 9 Air out frame assy Transformer Horizontal louver,up Terminal Horizontal louver, down 2 19 Indoor fan motor Display lamp panel 1 20 Wheel volute for slim type Installing box for display panel 1 21 Pipe clamp Foam for air outlet frame 2 22 Left gland for motor shaft sleeve Vertical step motor 1 23 Right gland for motor shaft sleeve Horizontal step motor Motor separating board Horizontal step motor 1 25 Holder for fan motor Display film 1 26 Weld assembly for intermediate transverse girder Endbearing of louver 4 27 Right mounting plate of evaporator Intermediate bearing of louver 8 28 Evaporator Driving lever for louver 2 29 Evaporator into the liquid component Follower lever for louver Shunt capillary component Louver holder Electronic expansion valve, pre-welded components Guard vane Air inlet header pipe assembly of evaporator 1 10 Chassis Single Connector 1 11 Left retaining plate 2 31 Left mounting plate of evaporator 1 12 Right retaining plate 2 32 Weld assembly of Water drain pan 1 13 Filter snap-gauge Water outlet rubber cover 1 14 Air inlet grille 2 33 Remote controller 1 15 Filter 4