LIQUIDATOR 450 SERIES

Size: px
Start display at page:

Download "LIQUIDATOR 450 SERIES"

Transcription

1

2 LIQUIDATOR 450 UMT SERIES TRAP AND UMTC CONNECTOR APPLICATIONS Unit Heaters Steam Tracing Drip Legs Tire Presses Cooking Equipment Laundry Equipment Plating Tanks Platen Presses Air Vents OPTIONS SLR - SLR Orifice* ISO - ISO Filled Actuator* SW - Socketweld B - Blowdown Valve *Not available on UMT451T Canadian Registration # OE1388.6C LIQUIDATOR 450 SERIES UNIVERSAL MOUNT THERMOSTATIC Pressures to 450 PSIG (31 barg) Temperatures to 600 F (316 C) Easily Maintained Universal two bolt swivel mounting simplifies removal from system. Kits allow flexibility to replace or rebuild. Simple Installation Stainless mounting block mounts permanently into system. Trap installs via two bolt universal connection. Improved Energy Savings High efficiency maximum elimination of air and non-condensibles. Temperature Sensitive Actuators One moving part. Stainless Steel, fail open, welded actuator for maximum corrosion, thermal and hydraulic shock resistance. Hardened Stainless Steel Valve and Seat Long life. Lapped as a matched set for water tight seal. Easily Maintained Can be inspected and serviced without breaking pipe connections. Freeze Proof Self draining when installed vertically. For Superheated Steam Applications Because the trap closes at saturated steam temperature, superheated steam cannot reach trap. Air Vent Efficient steam service air vent when equipped with ISO filled Actuator and installed in air vent location. Guaranteed Traps are guaranteed against defects in materials or workmanship for three years. Positive Shutoff and Long Life Integral Stainless Steel Strainer helps prevent debris depositing on valve and seat. MODELS UMT-TD10L Low Capacity Trap UMT-TD10 Standard Capacity Trap UMTC Standard connector (1/2" & 3/4" only) UMTCY-RH Right Hand Connector w/y strainer* UMTCY-LH Left Hand Connector w/y strainer* UMTVS-BB Connector with Isolation Valves, Strainer, Blowdown Valve and Test Port For complete unit, order trap and connector as separate items. *Add (-B) for Blowdown Valve. For information on Big Block UMTVS-BB Connector See Page 344 OPERATING PRINCIPLE Thermal actuator is filled at its free length with a liquid having a lower boiling point than water. On start-up, valve is normally open. When steam enters trap, thermal actuator fill vaporizes to a pressure higher than line pressure. This forces valve into seat orifice to prevent any further flow. As condensate collects, it takes heat from thermal actuator, lowering internal pressure. Line pressure will then compress thermal actuator to open valve and discharge condensate. Valve opening automatically adjusts to load conditions from minimum on very light loads to full lift at maximum load. Restricted orifice in UMT451T (small opening at bottom of valve seat) prevents trap from discharging continuously on light loads such as are encountered on tracer lines

3 LIQUIDATOR 450 SERIES UNIVERSAL MOUNT THERMOSTATIC SPECIFICATIONS Steam trap shall be of balanced pressure design with stainless steel welded actuator capable of discharging condensate within 10 F of saturated temperature. Where greater sensitivity is required, SLR orifice and Sterilizer trim will be available to allow condensate evacuation at or near saturated temperatures. Where subcooling of condensate is desired alternate thermostatic actuator will be available to allow condensate evacuation at or near 40 F below saturated temperatures. Thermostatic actuator shall employ a conical valve lapped in matched sets with the seat ring assuring tight shut off. A minimum of two orifice sizes shall be available allowing for custom capacity sizing. Trap shall be stainless steel bodied suitable for pressures through 450 psig. Trap connection shall be two bolt universal swivel mount. Mounting block shall be stainless steel and available in 1 2" through 1" NPT or socket weld. MAXIMUM OPERATING CONDITIONS Traps with Welded Stainless Actuator PMO: Max. Operating Pressure 450 psig (31 barg) TMO: Max. Operating Temperature 600 F (316 C) Traps with Welded Stainless Actuator, ISO PMO: Max. Operating Pressure 450 psig (31 barg) TMO: Max. Operating Temperature 600 F (316 C) All Traps PMA: Max. Allowable Pressure 450 psig (31 barg) TMA: Max. Allowable Temperature 750 F (399 C) 3.44 (8.74) UMT SERIES TRAP AND UMTC CONNECTOR Connections: 1/2", 3/4" or 1" NPT or socketweld 3.5 (8.89) 4.8 (122).75 (19) 1.25 (3.18) 2.6 sq. (66 sq.) 2.81 (71) 5 (12.7) UMTCYR LIQUIDATOR 450 MATERIALS OF CONSTRUCTION Body & Cover ASTM A351 Grade CF8 (304) Cover Gasket stainless spiral wound w/graphite fill Actuator Welded SS Strainer.033 perf. 304 Stainless Steel Valve & Seat Hardened 416 Stainless Steel Mounting Block ASTM A351 Grade CF8 (304) 5 (12.7) UMTCYL 1.25 (3.18) 3.5 (8.89) 3.44 (8.74) DIMENSIONS - INCHES (MM) WEIGHT TRAP LBS. (1.4 KG) STD. MOUNTING BLOCK LBS. (0.5 KG) Y STRAINER MOUNTING BLOCK LBS. (1.0 KG) Maximum Capacity lbs/hr 10 F Below Saturation (Kg/hr 5 C Below Saturation) Orifice Differential PSIG (barg) Trap Inch (mm) (0.34) (0.7) (1.4) (3.4) (6.7) (8.4) (10.1) (13.4) (16.8) (20.1) (24.1) (27.6) (31.0) UMT451T 5/ (2) (38) (54) (76) (120) (158) (170) (181) (199) (214) (228) (240) (251) (261) UMT452T 1/ (3) (98) (120) (170) (269) (354) (381) (405) (445) (480) (510) (536) (561) (584) UMT453T 1/ (6) (249) (374) (549) (896) (1281) (1424) (1554) (1656) (1796) (1860) (1919) (2005) (2086) ISO filled Actuator recommended for superheated steam

4 DS200 SERIES APPLICATIONS Drainage of Steam Filters and Separators Culinary Steam WFI System Sterilization Main Drips Sterilizer Drainage and Air Venting DS200 SERIES THERMOSTATIC Pressures To 100 PSIG (6.9 barg) Temperatures to 338 F (170 C) Stainless Steel Body Body materials are Type 316L Stainless Steel. Self Centering Valve Leak tight shut off. Assembly of actuator and valve to impingement plate allows valve to self-align with center of valve seat orifice. Provides long lasting valve and seat. Temperature Sensitive Actuator One moving part. Inconel welded actuator for maximum corrosion, thermal and hydraulic shock resistance. Thermal and Hydraulic Shock Resistant Impingement plate plus welded construction prevents damage to actuator. Valve and Seat Long life, stainless steel valve and seat lapped and matched together for water tight seal. Maintenance All models are sealed and maintenance free. Three Year Guarantee Trap guaranteed for three years against defects in material or workmanship. Additional Features Best air handling capability for fast start up and operation. Fastest response to condensate load or temperature changes. Broad application range. Selection of orifice and pipe sizes meet majority of condensate removal demands in deionized steam systems. Unique SLR Orifice Option Provides drainage at saturated temperatures, instant reaction to load changes and guaranteed fail-open operation for extra critical operations. MODELS DS202 Low capacity DS203 Medium capacity DS204 High capacity OPTIONS SLR - SLR Orifice Canadian Registration # OE0591.9C OPERATION Thermal actuator is filled at its free length with a liquid having a lower boiling point than water. On start-up, valve is normally open to discharge air, non-condensibles and condensate. When steam enters trap, thermal actuator fill vaporizes to a pressure higher than line pressure. This forces valve into seat orifice to prevent any further flow. As condensate collects, it takes heat from thermal actuator, lowering internal pressure. Line pressure will then compress thermal actuator to open valve and discharge condensate. Valve opening automatically adjusts to load conditions from minimum on very light loads to full lift at maximum load

5 DS200 SERIES THERMOSTATIC SPECIFICATION Steam trap shall be of balanced pressure design with inconel welded bellows capable of releasing condensate within 10 F of saturated pressure. Where drainage at saturated temperatures is required, trap shall have SLR orifice. All other components shall be of 316 or 316L stainless steel. Trap shall be self draining and normally open. MAXIMUM OPERATING CONDITIONS B A 3/8" - 3/4" BODY DS200 SERIES PMO: Max. Operating Pressure 100 psig (6.9 barg) TMO: Max. Operating Temperature 338 F (170 C) PMA: Max. Allowable Pressure 150 psig (10.3 barg) TMA: Max. Allowable Temperature 366 F (186 C) A MATERIALS OF CONSTRUCTION Body ASTM 743 CF-8M Stainless Steel Welded Actuator 316L Fittings & Plates Valve & Seat 316L Stainless Steel B 1" BODY SLR ORIFICE OPTION Specify when immediate elimination of condensate and improved sensitivity is desired. A 1/32" orifice at the apex of the valve allows for continuous discharge of condensate. Trap will nominally pass 50 lbs/hr of condensate at 50 psi within 2 F of saturated temperature. Connections: 3/8" 1" NPT or Socketweld Dimensions NPT or inches Weight Socket (mm) Lbs. weld A B (kg) 3 /8", 1 /2" 3 3 /4 (95) 1 3 /4 (44) 1.1 (0.5) 3 /4" 1" 3 15 / /4 1.2 (100) (44) (0.54) 4 3 /8 1 3 /4 1.6 (111) (44) (0.73) Maximum Capacity lbs/hr 10 F Below Saturation (Kg/hr 5 C Below Saturation) Orifice Differential PSIG (bar) Trap Inch (mm) (0.34) (0.7) (1.4) (3.5) (6.9) (8.6) (10.3) (13.8) (17.2) (20.7) (24.1) (27.6) (31.0) (34.5) DS202 1/ (3) (98) (120) (170) (269) (354) (381) (405) (445) (480) (510) (536) (561) (584) (601) DS203 DS204 1/ (6) (249) (374) (549) (896) (1281) (1424) (1554) (1656) (1796) (1860) (1919) (2005) (2086) (2161) 5/ (8) (390) (554) (783) (1237) (1623) (1748) (1857) (2045) (2202) (2340) (2463) (2576) (2679) (2774)

6 NICHOLSON STEAM TRAP N125 SERIES THERMOSTATIC Pressures To 125 PSIG (8.75 barg) Temperatures to 400 F (204 C) Applications Steam Tracing Drip Legs Automatic Air Vents Sterilizers Cooking Kettles Water Heaters Laundry Equipment Radiators Process Equipment Air Handlers Options See page 8 SS Actuator or Convoluted Monel Bellows Sterilizer Trim SLR Orifice Internal Stainless Strainer ISO Filled Actuator Superior Performance Hardened valve and seats are lapped in matched sets, providing tight shutoff and long service life. Improved Energy Savings Maximum elimination of air and non-condensibles trap closes at saturated steam temperature. Temperature Sensitive Actuators One moving part. Monel actuator for caustic corrosion resistance.choose Stainless Steel, fail open, welded actuator for maximum corrosion, thermal and hydraulic shock resistance. Freeze Proof Threaded male union horizontal inlet and vertical outlet self draining. In-line Maintenance Threaded cover for one step removal, inspection and service without breaking pipe connections. Air Vent Efficient steam service air vent when equipped with ISO Bellows and installed in air vent location. Guaranteed Traps with convoluted bellows are guaranteed against defects in materials or workmanship for 1 year and traps with welded actuator for 3 years. Models N125 Standard capacity w/monel actuator N125W Standard capacity w/welded SS actuator N125L Low capacity w/welded SS actuator N125WHC High capacity w/welded SS actuator N125HC High capacity w/monel actuator N125ST Standard capacity w/sterilizer seat & monel actuator Operating Principle Thermal actuator is filled at its free length with a liquid having a lower boiling point than water. On start-up, valve is normally open. When steam enters trap, thermal actuator fill vaporizes to a pressure higher than line pressure. This forces valve into seat orifice to prevent any further flow. As condensate collects, it takes heat from thermal actuator, lowering internal pressure. Line pressure will then compress thermal actuator to open valve and discharge condensate. Valve opening automatically adjusts to load conditions from minimum on very light loads to full lift at maximum load. Restricted orifice in N125L (small opening at bottom of valve seat) prevents trap from discharging continuously on light loads Fax: A2

7 NICHOLSON STEAM TRAP N125 SERIES THERMOSTATIC Typical Specification Steam trap shall be of balanced pressure design with monel convoluted actuator or stainless steel welded actuator capable of discharging condensate within 10 F of saturated temperature. Where greater sensitivity is required, SLR orifice and Sterilizer trim will be available to allow condensate evacuation at or near saturated temperatures. Where subcooling of condensate is desired alternate thermostatic actuator will be available to allow condensate evacuation at or near 40 F below saturated temperatures. Thermostatic actuator shall employ a conical valve lapped in matched sets with the seat ring assuring tight shut off. A minimum of three orifice sizes shall be available allowing for custom capacity sizing. Trap shall be bronze bodied suitable for pressures through 125 psig and available in 3/8" through 3/4" NPT connections. Maximum Operating Conditions PMO: Max. Operating Pressure 125 psig (8.75 barg) TMO: Max. Operating Temperature 400 F (204 C) PMA: Max. Allowable Pressure 125 psig (8.75 barg) TMA: Max. Allowable Temperature 400 F (204 F) Materials of Construction Body & Cover: ASTM B283 C37700 Actuator: Convoluted Monel or Welded Stainless Steel Cover Gasket: Copper Jacketed Valve & Seat: Hardened 416 Stainless Steel B Dimensions Size 3 /8, 1 /2" 3 /4" A D C Connections: 3/8" 3/4" NPT Inch (mm) Weight lb A B C D (kg) 2 3 /4 1 1 /8 2 7 /8 2 5 / (70) (29) (73) (54) (.68) 3 3 / / / (81) (40) (76) (54) (.82) SIZING INFO APPLICATION GUIDE SELECTION CHECKLIST Maximum Capacity lbs/hr 10 F Below Saturation (Kg/hr 5 C Below Saturation) Trap Orifice Differential PSIG (barg) Inch (mm) (0.34) (0.7) (1.4) (3.5) (6.9) (8.6) N125L 2 5/ (2) (38) (54) (76) (120) (158) (170) N / N125W 2 (6) (249) (374) (549) (896) (1281) (1424) N125ST 1 N125WHC 2 5/ N125HC 1 (8) (390) (554) (783) (1237) (1623) (1748) 1 Convoluted Monel Actuator 2 Welded Thermal Actuator Fax: A3

THERMOSTATIC STEAM TRAPS

THERMOSTATIC STEAM TRAPS THERMOSTATIC STEAM TRAPS Nicholson is the originator of the bellows actuated Thermostatic Steam. Nicholson s thermostatic product range spans applications from critical tracing to high capacity process.

More information

THERMODYNAMIC STEAM TRAPS

THERMODYNAMIC STEAM TRAPS THERMODYNAMIC STEAM TRAPS Nicholson has a wide variety of Thermodynamic Steam Traps to accommodate applications through 600 psi. Most models utilize Nicholson s exclusive Celtron Cartridge. The Celtron

More information

LIQUIDATOR UMT-TD Series Thermodynamic

LIQUIDATOR UMT-TD Series Thermodynamic 52 LIQUIDATOR UMT-TD Series Thermodynamic Applications Steam Trap Unit Heaters Steam Tracing Drip Legs Tire Presses Laundry Equipment Plating Tanks Platen Presses Cooking Equipment Pressures To 450 PSIG

More information

THERMODYNAMIC STEAM TRAPS

THERMODYNAMIC STEAM TRAPS 53 STEAM TRAPS has a wide variety of Thermodynamic Steam Traps to accommodate applications through 600 psi. Most models utilize s exclusive Celtron Cartridge. The Celtron facilitates inline maintenance

More information

NICHOLSON STEAM TRAP THERMODYNAMIC STEAM TRAPS

NICHOLSON STEAM TRAP THERMODYNAMIC STEAM TRAPS THERMODYNAMIC S has a wide variety of Thermodynamic Steam Traps to accommodate applications through 600 psi. Most models utilize s exclusive Celtron Cartridge. The Celtron facilitates inline maintenance

More information

THE THERMOSTATIC STEAM TRAP

THE THERMOSTATIC STEAM TRAP THE THERMOSTATIC STEAM TRAP The purpose of any steam trap is to discharge, promptly, all condensate (as well as air and other non-condensible gases) without discharging live steam. Since steam is a vapor

More information

UNIVERSAL STYLE STEAM TRAPS WU450 Series

UNIVERSAL STYLE STEAM TRAPS WU450 Series Watson McDaniel reserves the 2010 Watson McDaniel Company UNIVERSL STYLE STEM TRPS WU450 Series Universal Connectors for Universal Steam s STEM TRPS Model WU450, WU450S, WU450SB WU450S-LR, WU450SB-LR,

More information

FT600 & FT601* Steam Traps Float & Thermostatic Steam Trap. Float & Thermostatic STEAM TRAPS

FT600 & FT601* Steam Traps Float & Thermostatic Steam Trap. Float & Thermostatic STEAM TRAPS STEAM TRAPS Steam Traps Steam Trap Model * Sizes 3/4, 1, 1 1 /2, 2, 3, 4 Connections NPT, SW, FLG Body Material Carbon Steel or 316SS Options Live Orifice Air Vent PMO Max. Operating Pressure 450 PSIG

More information

Liquid Drainers LIQUID DRAINERS

Liquid Drainers LIQUID DRAINERS Liquid Drainers 206 Liquid Drainers Model/Series Type Body Material PMO Sizes Connection Page No. (PSIG) WLDE Float Ductile Iron 200 1 1 /2, 2, 2 1 /2 NPT WLDES Float Cast Steel 300 2 1 /2 NPT, SW, FLG

More information

Yarway Repairable Drip and Tracer Steam Traps Series 751/761, 711/721, 731/741, 500/546, 460/515/D3

Yarway Repairable Drip and Tracer Steam Traps Series 751/761, 711/721, 731/741, 500/546, 460/515/D3 Wide range of steam traps that provide consistent performance in less than perfect conditions Features 1 1 Thermostatic Traps Repairable Pressure assisted fail-open design Freeze proof Easy to check cyclic

More information

Technical Data CONDENSATE COMMANDER PUMP SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY SD 9902D

Technical Data CONDENSATE COMMANDER PUMP SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY SD 9902D Technical Data SD 9902D SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY 12586-2035 PRINTED IN U.S.A. SD 79902D/9803 Condensate Commander Pump Dimensions Weight Size A B C D E* F Lbs. 1"x

More information

Economical and simplified solutions that offer quality and optimum steam trap service.

Economical and simplified solutions that offer quality and optimum steam trap service. Economical and simplified solutions that offer quality and optimum steam trap service. It All Comes Down To Protection Regardless of the temperature and pressure characteristics of steam line drips or

More information

YARWAY PROCESS THERMODYNAMIC STEAM TRAPS SERIES 40/40D AND C250/260

YARWAY PROCESS THERMODYNAMIC STEAM TRAPS SERIES 40/40D AND C250/260 SERIES 40/40D AND C250/260 Designed for a variety of high pressure and high capacity applications found in utility, industrial and marine service FEATURES Designed to fail open. Designed for superheat

More information

PT15 MATERIAL : DIMENSIONS - Nominal in inches. AVAILABLE SPARES: Disc (Packet of 5) ORDERING INFORMATION: Refer to "HOW TO ORDER" page.

PT15 MATERIAL : DIMENSIONS - Nominal in inches. AVAILABLE SPARES: Disc (Packet of 5) ORDERING INFORMATION: Refer to HOW TO ORDER page. PT5 Thermodynamic Steam Traps MATERIAL : No. PART MATERIAL QTY. (Nos.). BODY ASTM A743 Gr. CA 40 0 (Seat Hardened) (Cast Equiv. AISI 420) 2. DISC CAP ASTM A743 Gr. CA 40 0 (Cast Equiv. AISI 420) 3. DISC

More information

Inverted Bucket Float & Thermostatic Radiator Traps STEAM CONTROL PRODUCTS STEAM TRAPS

Inverted Bucket Float & Thermostatic Radiator Traps STEAM CONTROL PRODUCTS STEAM TRAPS Inverted Float & Radiator Traps STEAM CONTROL PRODUCTS STEAM TRAPS ABOUT US In 1916, the company, then known as the Sterling Engineering Company, began designing and manufacturing valves, traps, strainers

More information

YARWAY NON-REPAIRABLE DRIP AND TRACER STEAM TRAPS SERIES PB, 29, 129Y AND 29S

YARWAY NON-REPAIRABLE DRIP AND TRACER STEAM TRAPS SERIES PB, 29, 129Y AND 29S SERIES PB, 29, 129Y AND 29S Economical and simplified solutions that offer quality and optimum steam trap service FEATURES 29S 29 Thermostatic traps Pressure assisted fail-open design Freeze proof Easy

More information

Condensate Pumps Jones Boulevard Limerick Airport Business Center Pottstown PA Tel:

Condensate Pumps Jones Boulevard Limerick Airport Business Center Pottstown PA Tel: www.watsonmcdaniel.com 428 Jones Boulevard Limerick Airport Business Center Pottstown PA 19464 Tel: 610-495-5131 129 Return Introduction Return System Shown below is a simplified view of a steam system

More information

CD-33/CD-33S Controlled Disc Steam Traps

CD-33/CD-33S Controlled Disc Steam Traps D-33/D-33S ontrolled Disc Adapts to outdoors Optional rain guard insulating cap available to prevent excessive radiant heat loss in outside applications. Extended life Three discharge port design offers

More information

Hoffman Specialty General Catalog

Hoffman Specialty General Catalog Hoffman Specialty General Catalog HS-900E ESP-PLUSTM For computer aided selection of Steam Trap and Regulators, please refer to the Steam Specialty Component Selectors in the Hoffman Specialty website

More information

S and SF Inverted Bucket Steam Traps Installation and Maintenance Instructions

S and SF Inverted Bucket Steam Traps Installation and Maintenance Instructions 0772150/4 IM-P077-02 ST Issue 4 S and SF Inverted Bucket Steam Traps Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation 4. Commissioning

More information

Pump & Trap Combinations

Pump & Trap Combinations NON-ELECTRIC CONDENSATE Pump & Trap Combinations Why use a Pump-Trap? Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company

More information

opening trap 30 mm Space required for Space required for opening trap 30 mm MK 45-1 with flanged ends (to DIN)

opening trap 30 mm Space required for Space required for opening trap 30 mm MK 45-1 with flanged ends (to DIN) Issue Date: 4/06 GESTRA Steam Systems Thermostatic Steam Traps MK 45-, MK 45-2 PN 40, DN 5, 20, 25 (½", ¾", ") Product Range A MK 45- MK 45-2 Description Thermostatic steam trap with membrane regulator.

More information

STEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD

STEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is

More information

Our Know-How. Your Peace of Mind. Steam Solutions

Our Know-How. Your Peace of Mind. Steam Solutions Our Know-How. Your Peace of Mind. Steam Solutions Steam Solution Know-How Our team of specialists have years of experience in planning and engineering. This knowledge, combined with our valuable manufacturer

More information

TABLE OF CONTENTS STEAM TRAPS INVERTED BUCKET SERIES PAGE FLOAT AND THERMOSTATIC SERIES PAGE THERMOSTATIC THERMODISC B0 26. How to Select All 107

TABLE OF CONTENTS STEAM TRAPS INVERTED BUCKET SERIES PAGE FLOAT AND THERMOSTATIC SERIES PAGE THERMOSTATIC THERMODISC B0 26. How to Select All 107 TABLE OF CONTENTS FLOAT AND THERMOSTATIC SERIES PAGE How to Select All 107 C 14 H 8 I 12 X 14 Competitive Changeover 18 THERMOSTATIC 8C 22 9C 2 17C 20 Competitive Changeover 17C 24 Replacement Modules

More information

Product. Add Efficiency To Your Steam Investment... Steam Traps Drain Traps Air Vents & Eliminators Accessories Piping Assemblies Replacement Kits

Product. Add Efficiency To Your Steam Investment... Steam Traps Drain Traps Air Vents & Eliminators Accessories Piping Assemblies Replacement Kits Engineering Products for the Steam Industry Since 985 Product Catalog Steam Traps Drain Traps Air Vents & Eliminators Accessories Piping Assemblies Replacement Kits Add Efficiency To Your Steam Investment...

More information

Float & Thermostatic Steam Traps for efficient condensate drainage of industrial process and HVAC equipment

Float & Thermostatic Steam Traps for efficient condensate drainage of industrial process and HVAC equipment Float & Thermostatic Steam Traps for efficient condensate drainage of industrial process and HVAC equipment Float & Thermostatic Steam Traps from Spirax Sarco About float & thermostatic steam traps Most

More information

Wide range of steam traps that provide consistent performance in less than perfect conditions.

Wide range of steam traps that provide consistent performance in less than perfect conditions. Wide range of steam traps that provide consistent performance in less than perfect conditions. It ll omes Down To Protection Regardless of the temperature and pressure characteristics of steam line drips

More information

Technical Data TYPE T14 & T14D TEMPERATURE PILOT SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY SD 4511A T14 PILOT

Technical Data TYPE T14 & T14D TEMPERATURE PILOT SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY SD 4511A T14 PILOT Technical Data SD 4511A SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY 12586-2035 TYPE T14 & T14D TEMPERATURE PILOT PRINTED IN U.S.A. SD 4511A/9811 5 13 /16 D 4 7 /8 1 13 /16 T14 PILOT

More information

Series 151 and AV5. A wide range of process thermostatic steam traps is available to match almost any application need.

Series 151 and AV5. A wide range of process thermostatic steam traps is available to match almost any application need. A wide range of process thermostatic steam traps is available to match almost any application need. FEATURES Simple construction Easy to maintain as installed Excellent air handling capability Pressure

More information

Hydrocarbon & Chemical Processing Solutions

Hydrocarbon & Chemical Processing Solutions Hydrocarbon & Chemical Processing Solutions Table of Contents Armstrong Packaged Piping Solutions...3-4 Steam Distribution Manifolds (MSD/SMSD) & Cost Comparison Worksheet...5-7 Condensate Collection Assembly

More information

Inverted Bucket Steam Traps. for efficient condensate drainage of industrial and HVAC equipment

Inverted Bucket Steam Traps. for efficient condensate drainage of industrial and HVAC equipment Inverted ucket Steam Traps for efficient condensate drainage of industrial and HVC equipment Inverted ucket steam traps The proper drainage of condensate is essential to efficient steam system operation.

More information

Air Vents AV-392. Proven Same proven, free-floating all stainless steel mechanism as used in Armstrong steam traps.

Air Vents AV-392. Proven Same proven, free-floating all stainless steel mechanism as used in Armstrong steam traps. Proven Same proven, free-floating all stainless steel mechanism as used in Armstrong steam traps. Leak-tight Positive closing, free-floating stainless steel lever ensures leak-tight closing under all conditions.

More information

STEAM TRAPS

STEAM TRAPS STEAM TRAPS 08.2016 info@ayvaz.com www.ayvaz.com SELECTION OF STEAM TRAPS In order to get maximum efficiency and service life from the steam lines and steam related systems, it is crucial to make the correct

More information

Armstrong Steam System Solutions for the Hydrocarbon and Chemical Processing Industries

Armstrong Steam System Solutions for the Hydrocarbon and Chemical Processing Industries Bulletin 290-B Armstrong Steam System Solutions for the Hydrocarbon and Chemical Processing Industries Packaged Piping Solutions - Steam Distribution Manifolds - Condensate Collection Assemblies - Trap

More information

YARWAY PROCESS THERMOSTATIC STEAM TRAPS SERIES 151 AND AV5

YARWAY PROCESS THERMOSTATIC STEAM TRAPS SERIES 151 AND AV5 A wide range of process thermostatic steam traps is available to match almost any application need FEATURES Simple construction Easy to maintain as installed Excellent air handling capability Pressure

More information

FLOAT AND THERMOSTATIC STEAM TRAPS FLT17 (DN 1/2 to 1 ; DN15 to DN25)

FLOAT AND THERMOSTATIC STEAM TRAPS FLT17 (DN 1/2 to 1 ; DN15 to DN25) LOAT AND THERMOSTATIC STEAM TRAPS LT17 (DN 1/2 to 1 ; DN15 to DN25) DESCRIPTION LT17 float and thermostatic (integral air vent) steam traps series are designed for all types of low and high pressure steam

More information

High Capacity Instantaneous Steam Fired Water Heater

High Capacity Instantaneous Steam Fired Water Heater MODEL F High Capacity Instantaneous Steam Fired Water Heater Features Compact High Capacity Design Packaged System Water heater is factory assembled on an all welded steel mounting frame to save time and

More information

The right trap for the right application.

The right trap for the right application. The right trap for the right application. Whenever you re faced with a process application, it s not enough to just select any steam trap to solve your problem. Instead, remember to match your application

More information

Installation and Maintenance Manual Forbes Marshall Tracer Line Trap FMMST63

Installation and Maintenance Manual Forbes Marshall Tracer Line Trap FMMST63 Installation and Maintenance Manual Forbes Marshall Tracer Line Trap Energy Conservation Environment Process Efficiency www.forbesmarshall.com Table of Contents 1. Preface...1 2. Important Safety Notes...1

More information

Pamphlet A2404. Mechanical Pump & Pump/ Trap. GP Series GT Series

Pamphlet A2404. Mechanical Pump & Pump/ Trap. GP Series GT Series Pamphlet A2404 Mechanical Pump & Pump/ Trap GP Series GT Series Effective Processing Improves Plant Efficiency Increased productivity and product quality, plus reduced energy consumption and water treatment

More information

Essex County College - West Essex Campus Addition And Renovations dib # / SECTION HYDRONIC PIPING SPECIALTIES PART 1- GENERAL

Essex County College - West Essex Campus Addition And Renovations dib # / SECTION HYDRONIC PIPING SPECIALTIES PART 1- GENERAL Essex County College - West Essex Campus Addition And Renovations dib # 54292 / 11-14 SECTION 232116 - HYDRONIC PIPING SPECIALTIES PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions

More information

Ball Float Steam Trap with Integral Spiratec Sensor and Flanged Connections

Ball Float Steam Trap with Integral Spiratec Sensor and Flanged Connections Page 1 of TI-P615-03 ST Issue IFT57 SG Iron ISO 9001 Ball Float Steam Trap with Integral Spiratec Sensor and Flanged Connections Cert. No. LRQ 0963008 IFT57H DN0 (horizontal shown) DN15 (vertical shown)

More information

Armstrong Steam System Solutions for the Hydrocarbon and Chemical Processing Industries

Armstrong Steam System Solutions for the Hydrocarbon and Chemical Processing Industries Bulletin 290-C Armstrong Steam System Solutions for the Hydrocarbon and Chemical Processing Industries Packaged Piping Solutions - Steam Distribution Manifolds - Condensate Collection Assemblies - Trap

More information

Pure Performance For Steam Mains and Tracers

Pure Performance For Steam Mains and Tracers Pamphlet A2004-2 Thermodynamic Steam Traps P Series FP Series HR Series Pure Performance For Steam Mains and Tracers Are you looking for Improved Performance? Disc traps are valued for their compact size

More information

MODELS N150/300/675/900/1500/2500/2600 INSTALLATION, SERVICING AND MAINTENANCE INSTRUCTIONS

MODELS N150/300/675/900/1500/2500/2600 INSTALLATION, SERVICING AND MAINTENANCE INSTRUCTIONS MODELS N150/300/675/900/1500/2500/2600 INSTALLATION, SERVICING AND MAINTENANCE INSTRUCTIONS 1. FEATURES The Type N Trap range is particularly suitable for high pressure/high temperature trapping applications

More information

ESCO. Committed. Group of Companies. to help conserve Steam Energy

ESCO. Committed. Group of Companies. to help conserve Steam Energy Group of Companies Committed to help conserve Steam Energy Company Profile Group of Industries was established in 1977 as an Energy Conservation as well as Industrial Equipments manufacturing Company concentrating

More information

ICS Float and Thermostatic Steam Trap Installation and Operation Manual

ICS Float and Thermostatic Steam Trap Installation and Operation Manual ICS Float and Thermostatic Steam Trap Installation and Operation Manual 59 Table of Contents. General Safety Information. 3 Product Information. 4 Product Installation. 5 Service and Maintenance. 6 Troubleshooting.

More information

AIC Series Float & Thermostatic Steam Trap Installation and Maintenance Instructions

AIC Series Float & Thermostatic Steam Trap Installation and Maintenance Instructions AIC Series Float & Thermostatic Steam Trap Installation and Maintenance Instructions 138-EN Please read and save these instructions Contents General Safety Information... 3 Product Information...3-5 Product

More information

Steam Traps and Steam Specialties

Steam Traps and Steam Specialties Steam Traps and Steam Specialties The new shape in steam traps... Bestobell s Delta Element A sophisticated, yet simple, design that will provide years of trouble-free service with no live steam loss.

More information

WHY THE REMOVAL OF NONCONDENSABLE GASES AND AIR IS CRITICAL IN A STEAM SYSTEM

WHY THE REMOVAL OF NONCONDENSABLE GASES AND AIR IS CRITICAL IN A STEAM SYSTEM BEST PRACTICE NO. 30 WHY THE REMOVAL OF NONCONDENSABLE GASES AND AIR IS CRITICAL IN A STEAM SYSTEM Air and noncondensable gases are one of the major problems in a steam system that can cause production

More information

FT14 Ball Float Steam Trap (Screwed)

FT14 Ball Float Steam Trap (Screwed) Page 1 of TI-S02-0 ST Issue 9 Cert. No. LRQ 096008 ISO 9001 FT14 Ball Float Steam Trap (Screwed) Description The FT14 is an SG iron bodied ball float steam trap having stainless steel working internals

More information

STAINLESS STEEL TRAP VALVE STATION

STAINLESS STEEL TRAP VALVE STATION STAINLESS STEEL TRAP VALVE STATION MAKES A LONG STORY... 36 [914 MM]...SHORT. 4.75 [121 MM] THE INNOVATION IS INTEGRATION Armstrong stainless steel Trap Valve Station (TVS) reduces your costs for installation,

More information

FT14 and FT14HC. SG Iron Ball Float Steam Traps (1" HC, 1¼", 1½" and 2")

FT14 and FT14HC. SG Iron Ball Float Steam Traps (1 HC, 1¼, 1½ and 2) Page 1 of TI-S0- ST Issue and HC ISO 9001 SG Iron Ball Float Steam Traps (1" HC, 1¼", 1½" and ") Cert. No. LRQ 09300 HC 1" 1¼" -C 1½" and " Description The and HC are iron bodied ball float steam traps

More information

Hose. Propane Hose. 1 X-treme Low Temp Bobtail Hose. Large Transfer Hose. Construction Tube: Cover: Reinforcement: Temp. Range:

Hose. Propane Hose. 1 X-treme Low Temp Bobtail Hose. Large Transfer Hose. Construction Tube: Cover: Reinforcement: Temp. Range: Propane For liquid or gaseous transfer of propane. 350 lb working pressure. All sizes are UL21 and CGA Type 1 approved. Cover is pin pricked for gas dissipation. I.D O.D Spirals Lbs per ft..610.15.760.22

More information

Armstrong J Series Float, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual

Armstrong J Series Float, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual Armstrong J Series, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual This bulletin should be used by experienced personnel as a guide to the installation

More information

ø D ø g ø k Max. service [barg] pressure [psig] H 1 96 L BK 45 with butt-weld ends End connections Screwed Socket-weld

ø D ø g ø k Max. service [barg] pressure [psig] H 1 96 L BK 45 with butt-weld ends End connections Screwed Socket-weld GESTRA Steam Trap RHOMBUSline BK 45 and BK 45U International patents Issue date: /00 BK 45 and BK 45U A Space required for opening trap 70 b Thermostatic steam trap with corrosion-resistant thermostatic

More information

Main Steam Vents. Hoffman Specialty Regulators. How to Select Steam Vents

Main Steam Vents. Hoffman Specialty Regulators. How to Select Steam Vents Hoffman Specialty Regulators Main Steam How to Select Steam Model Radiator Convector Unit Thermostatlic Number (Angle Type) (Bottom Inlet) Heater Mains Vent (only) Remarks 1A X Adjustable Orifice 70A X

More information

Removal of Non-condensable Gases and Air Is Critical In A Steam System

Removal of Non-condensable Gases and Air Is Critical In A Steam System Removal of Non-condensable Gases and Air Is Critical In A Steam System Air and non-condensable gases are one of the major problems in a steam system. Both can cause production problems for a steam system

More information

Valtek Guardian II Metal Bellows Seal Valtek Guardian II

Valtek Guardian II Metal Bellows Seal Valtek Guardian II Valtek Guardian II Metal Bellows Seal Control Valves Design Features No upper bellows gasket required Tell-tale tap for indicating leakage Bellows is out of flow stream, eliminating direct fluid impingement

More information

Steam Traps. . Chambered valves such as; bleeding & venting valves and steam traps. Float Valves using a free fl oat

Steam Traps. . Chambered valves such as; bleeding & venting valves and steam traps. Float Valves using a free fl oat s s Function Level control valves control liquid levels without the necessity of an external energy input. There are two types of level controllers including:. Chambered valves such as; bleeding & venting

More information

Ball Float Controlled. Thermo Dynamic(TD) Trap Safety Valve Condensate Pump Flash Vessel Moisture Separators Deaerator Head Steam Injector Sight Glass

Ball Float Controlled. Thermo Dynamic(TD) Trap Safety Valve Condensate Pump Flash Vessel Moisture Separators Deaerator Head Steam Injector Sight Glass Product of Quality Best Performance Ball Float Controlled Steam Traps Auto Drain Traps Float Valve Air Vent Valves Feed Control Valve Drain Control Valve Thermo Dynamic(TD) Trap Safety Valve Condensate

More information

HEAT EXCHANGER FORMULAS & EXAMPLE

HEAT EXCHANGER FORMULAS & EXAMPLE Formulas for Heat Exchanger System using a Modulating Control Valve Definition of Terms and Units: E = Mean Heat Transfer Rate or Heat Load (Btu/hr) E D = Design Heat Load (Btu/hr) U = Overall Heat Transfer

More information

Mini Pump Trap. Features: n Low maintenance - No leaking seals, impeller or motor problems reducing maintenance and downtime.

Mini Pump Trap. Features: n Low maintenance - No leaking seals, impeller or motor problems reducing maintenance and downtime. Armstrong Mini Pump Bulletin AFH-223 The Armstrong mini pump trap is the smallest non-electric solution that can move condensate or other liuids from lower to higher points and from lower to higher pressures.

More information

Pamphlet U2404. Mechanical Pump & Pump/ Trap. GP Series GT Series

Pamphlet U2404. Mechanical Pump & Pump/ Trap. GP Series GT Series Pamphlet U2404 Mechanical Pump & Pump/ Trap GP Series GT Series Effective Processing Improves Plant Efficiency Increased productivity and product quality, plus reduced energy consumption and water treatment

More information

SECTION Pipeline Ancillaries

SECTION Pipeline Ancillaries SECTION Pipeline Ancillaries ARMSTRONG PRODUCT CATALOGUE 380 Strainers STY085 Y strainer. Suitable for steam, water, air, gas and most non corrosive chemicals Body & cap: Bronze B-62 Strainer: 304 stainless

More information

Installation and Testing of Inverted Bucket Steam Traps Manual

Installation and Testing of Inverted Bucket Steam Traps Manual Installation and Testing of Inverted Bucket Steam Traps Manual 307-EN Please read and save these instructions Armstrong IB Traps Installation Before Installing Run pipe to trap. Before installing the trap,

More information

THERMODYNAMIC STEAM TRAP

THERMODYNAMIC STEAM TRAP THERMODYNAMIC STEAM TRAP Model 041 Model 043 041 043 For the extraction of steam condensates. For use in: steam piping, irons, laundries, tanks and vessels with condensate discharge, multiple plate presses,

More information

Yarway Narvik Steam Desuperheater Series 4300 TempLow

Yarway Narvik Steam Desuperheater Series 4300 TempLow For precise and economical control of steam temperature Features and benefits Easy installation Installation in straight, vertical or horizontal pipe. Minimal headroom is required for mounting Only standard

More information

COMMERCIAL ITEM DESCRIPTION TRAPS, STEAM

COMMERCIAL ITEM DESCRIPTION TRAPS, STEAM [INCH-POUND] A-A-60001A 14 December 2013 SUPERSEDING A-A-60001 June 17, 1997 COMMERCIAL ITEM DESCRIPTION TRAPS, STEAM The General Services Administration has authorized the use of this commercial item

More information

Pure Performance For Steam Mains and Tracers

Pure Performance For Steam Mains and Tracers Pamphlet M2004-2 Thermodynamic Steam Traps P Series FP Series HR Series Pure Performance For Steam Mains and Tracers Redefining the Disc Trap Concept Life Cycle Cost for steam trap management includes

More information

PRODUCTS. Expansion Joints Fire Fighting. Flexible Metal Hoses. Equipments. Insulation Solutions. Steam. Valves. Level Control.

PRODUCTS. Expansion Joints Fire Fighting. Flexible Metal Hoses. Equipments. Insulation Solutions. Steam. Valves. Level Control. PRODUCTS Expansion Joints Fire Fighting Equipments Flexible Metal Hoses Steam Equipments Valves Level Control Insulation Solutions VALVES FLEXIBLE METAL HOSES EXPANSION JOINTS LEVEL CONTROL EQUIPMENTS

More information

Disc Type Steam Trap TSD-42

Disc Type Steam Trap TSD-42 Disc Type TSD-42 TSD-42 is disc type steam trap for high pressure (maximum pressure: 4.2 MPa). It is compact and lightweight, and can be installed horizontally or vertically. Disc Ring By-Metal Valve seat

More information

Section H11 BLOWDOWN SEPARATORS CONTENTS FEATURES AND BENEFITS...H11-3 PRODUCT OFFERING...H11-3 SAMPLE SPECIFICATIONS...H11-11 ILLUSTRATIONS

Section H11 BLOWDOWN SEPARATORS CONTENTS FEATURES AND BENEFITS...H11-3 PRODUCT OFFERING...H11-3 SAMPLE SPECIFICATIONS...H11-11 ILLUSTRATIONS Section H BLOWDOWN SEPARATORS CONTENTS FEATURES AND BENEFITS...................................................H- PRODUCT OFFERING.......................................................H- SAMPLE SPECIFICATIONS...................................................H-

More information

Steam Trap Presentation for IDEA Distribution Workshop. Presenter: Joe Radle

Steam Trap Presentation for IDEA Distribution Workshop. Presenter: Joe Radle Steam Trap Presentation for IDEA Distribution Workshop Presenter: Joe Radle Proper Piping when Reducing Pipe Size Concentric reducer Eccentric reducer Correct Wrong Typical Steam Main Drip Station D Size

More information

PIP PNE00004 Steam Trap Guidelines

PIP PNE00004 Steam Trap Guidelines July 2016 Piping PIP PNE00004 Steam Trap Guidelines PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities, this Practice has been prepared from

More information

Guardian II Metal Bellows Seal. Valtek Guardian II Metal Bellows Seal Control Valves

Guardian II Metal Bellows Seal. Valtek Guardian II Metal Bellows Seal Control Valves Valtek Guardian II Metal Bellows Seal Control Valves Design Features No upper bellows gasket required. Tell-tale tap for indicating leakage Bellows is out of flow stream, eliminating direct fluid impingement

More information

Installation and Maintenance Manual

Installation and Maintenance Manual Installation and Maintenance Manual Forbes Marshall Thermodynamic Trap Energy Conservation Environment Process Efficiency www.forbesmarshall.com Table of Contents 1. Preface...1. Important Safety Notes...1

More information

Packaged Semi-Instantaneous Steam Fired Water Heater

Packaged Semi-Instantaneous Steam Fired Water Heater MODEL STX Packaged Semi-Instantaneous Steam Fired Water Heater Shell and Tube Style Heater Features Reliable Only high grade materials used in construction to ensure long operating life Heat exchange pressure

More information

GESTRA. Program for Universal Connections. The Smart Solutions

GESTRA. Program for Universal Connections. The Smart Solutions GESTRA Program for Universal Connections The Smart Solutions GESTRA a smart solution for your convenience With a background of more than years in the steam trap business, GESTRA has alays aimed at turning

More information

Pamphlet M2404. Mechanical Pump & Pump/ Trap. GP Series GT Series

Pamphlet M2404. Mechanical Pump & Pump/ Trap. GP Series GT Series Pamphlet M2404 Mechanical Pump & Pump/ Trap GP Series GT Series Effective Processing Improves Plant Efficiency Increased productivity and product quality, plus reduced energy consumption and water treatment

More information

Instant hot water Feed-Forward system unlimited supply accurate to +/- 4 F

Instant hot water Feed-Forward system unlimited supply accurate to +/- 4 F Count on Graham for proven reliability. Graham is one of the world s foremost designers and manufacturers of vacuum and heat transfer equipment with over a half-century of proven experience. Our in-house

More information

Pamphlet A2000. TL\l. Free Float Steam Trap Series

Pamphlet A2000. TL\l. Free Float Steam Trap Series - Pamphlet A2000 TL\l Free Float Steam Trap Series Free Float Steam Traps Revolutionizing Fluid Control Technology More than 40 years have passed since TUI introduced the free float concept to the steam

More information

SECTION SECTION DESIGN REQUIREMENTS

SECTION SECTION DESIGN REQUIREMENTS SECTION 26 09 SECTION 23 05 23 DESIGN REQUIREMENTS GENERAL DUTY VALVES GENERAL INFORMATION 1.1 This section applies to valves for hydronic and steam systems. DESIGN REQUIREMENTS 2.1 Design Criteria a.

More information

MECHANICAL STEAM TRAPS

MECHANICAL STEAM TRAPS 29 MHNIL STM TRPS s Mechanical Trap line continues their tradition of offering high value with traditional designs while simultaneously pushing the performance envelope with leading edge technology. s

More information

STEAM CONSERVATION GUIDELINES

STEAM CONSERVATION GUIDELINES STEAM CONSERVATION GUIDELINES FOR CONDENSATE DRAINAGE Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit for up-to-date information. CG-1 Table

More information

PF Series. Piston Actuated Valves

PF Series. Piston Actuated Valves PF Series Piston Actuated Valves PF Series Piston actuated valves About The PF Series The Spirax Sarco PF Range of Piston Actuated Valves (PAVs) provides a competitive solution for on/off applications

More information

Boiler Condensate Return Basics. Presented by Steve Connor February 24, 2016

Boiler Condensate Return Basics. Presented by Steve Connor February 24, 2016 Boiler Condensate Return Basics Presented by Steve Connor February 24, 2016 What We Are Covering Today? Brief review of the total steam system Why a proper condensate return system is so important Condensate

More information

Steam and Condensate Technology. Solutions which are brilliant in their simplicity. combined with a first-class design & consultancy service.

Steam and Condensate Technology. Solutions which are brilliant in their simplicity. combined with a first-class design & consultancy service. Steam and Condensate Technology Solutions which are brilliant in their simplicity combined with a first-class design & consultancy service. Steam Traps The Free Float - Principle Free Float Steam Traps

More information

GEM TRAP FITTING & MAINTENANCE INSTRUCTIONS

GEM TRAP FITTING & MAINTENANCE INSTRUCTIONS GEM TRAP FITTING & MAINTENANCE INSTRUCTIONS IMPORTANT Please read these instructions before fitting any traps. The following pages describe how each type of GEM Trap should be installed. If you are unsure

More information

DURA RIMP. Goodall Duracrimp coupling system: INFERNO ISO A and SUPER INFERNO. A safe crimping connection for our GOODALL steamhoses

DURA RIMP. Goodall Duracrimp coupling system: INFERNO ISO A and SUPER INFERNO. A safe crimping connection for our GOODALL steamhoses Goodall Duracrimp coupling system: A safe crimping connection for our GOODALL steamhoses INFERNO ISO 6134-2A and SUPER INFERNO QUALITY SOLUTIONS DURA RIMP Content 1. Goodall DuraCrimp : A total solution

More information

Bringing Energy Down to Earth

Bringing Energy Down to Earth Bringing Energy Down to Earth Say energy. Think environment. And vice versa. Any company that is energy conscious is also environmentally conscious. Less energy consumed means less waste, fewer emissions

More information

VS SERIES NH3 STEAM VAPORIZERS OPERATION MANUAL

VS SERIES NH3 STEAM VAPORIZERS OPERATION MANUAL VS SERIES NH3 STEAM VAPORIZERS Revised March 1997 OPERATION MANUAL CONTENTS PAGE 1. GENERAL................................... 1 Figure 1-1 - VS Series Vaporizer......................... B How to Select

More information

Vacuum Insulated Pipe

Vacuum Insulated Pipe Product Catalog Innovation. Experience. Performance. Vacuum Insulated Pipe Ensuring liquid supply capabilities. Any application - Any time Ensuring liquid supply capabilities. Any application - Any time

More information

VENTS. Main Steam Vents. How to Select Steam Vents. For Steam Vent selection information, please refer to Selection Guidelines on page 133.

VENTS. Main Steam Vents. How to Select Steam Vents. For Steam Vent selection information, please refer to Selection Guidelines on page 133. Main Steam How to Select Steam For Steam Vent selection information, please refer to Selection Guidelines on page 133. Model Radiator Convector Unit Thermostatlic Number (Angle Type) (Bottom Inlet) Heater

More information

Pipe Thread Heaters. Construction Features. Star Electric to Order Call " 2-1/2" Pipe Thread Heaters

Pipe Thread Heaters. Construction Features. Star Electric to Order Call  2-1/2 Pipe Thread Heaters Pipe Thread Heaters Construction Features " -/" Pipe Thread Heaters Element bends repressed uniformly to insure electrical insulation integrity. One piece forging hex, thread and riser assures reliability.

More information

Series 1140 and 1141 Temperature Regulators

Series 1140 and 1141 Temperature Regulators Hoffman Specialty Installation & Maintenance Instructions HS-504(E) Series 1140 and 1141 Temperature Regulators! CAUTION FOLLOW ALL INSTALLATION AND OPERATING INSTRUCTIONS. TURN OFF WATER OR STEAM BEFORE

More information

Model AV Alarm Valve With and Without Model RC-1 Retard Chamber European Conformity Valve Trim General Description

Model AV Alarm Valve With and Without Model RC-1 Retard Chamber European Conformity Valve Trim General Description Worldwide Contacts www.tyco-fire.com Model AV--00 Alarm Valve With and Without Model RC- Retard Chamber European Conformity Valve Trim General Description The TYCO Model AV--00 Alarm Valves DN, DN0, DN0,

More information

DELUGE VALVE MODEL: SD-DVH2 TECHNICAL DATA TRIM DESCRIPTION DESCRIPTION VALVE OPERATION. 82 ASTM A 216 WBC.

DELUGE VALVE MODEL: SD-DVH2 TECHNICAL DATA TRIM DESCRIPTION DESCRIPTION VALVE OPERATION. 82  ASTM A 216 WBC. DELUGE VALVE MODEL: SD-DVH2 TECHNICAL DATA NORMAL SIZE MATERIAL SEVICE PRESSURE THREADED OPENING MOUNTING FACTORY HYDOSTATIC TEST PRESSURE FLANGE CONNECTION WET PILOT SPRINKLER HEIGHT LIMITATION NET WEIGHT

More information

BASICS OF STEAM TRAPS BASICS OF STEAM TRAPS

BASICS OF STEAM TRAPS BASICS OF STEAM TRAPS BASICS OF STEAM TRAPS BASICS OF STEAM TRAPS WHY DO WE NEED STEAM TRAPS? In order to operate economically and efficiently, all steam systems must be protected against 3 factors: * CONDENSATE * AIR * NON-CONDENSIBLES

More information