Condair Esco. Steam humidification system INSTALLATION INSTRUCTIONS EN 1310

Transcription

1 Condair Esco Steam humidification system L INSTALLATION INSTRUCTIONS EN 1310

2

3 3 Contents 1 Introduction General Safety 4 2 Esco DL Overview Esco DL Mounting the Esco DL Mounting the Esco DL40 with one steam pipe Mounting the Esco DL40 with two/three steam pipes 10 3 Esco DR Overview Esco DR Mounting the Esco DR73 A type Mounting the Esco DR73 B type 26 4 Esco DR73 J Overview Esco DR73 J Mounting the Esco DR73 J (Jumbo) 33 5 Mounting the steam supply line, the primary and secondary condensate and the manometer Connect the steam supply line (by client) Mounting the secondary condensate drain Mounting the primary condensate drain Thermostatic steam trap for Esco cast-iron and stainless steel versions Spheric float drain for Esco cast-iron version Bell-shaped float drain for Esco cast-iron version Spheric float drain and bell-shaped float drain for Esco stainless steel versions Spheric float drain for Esco stainless steel versions Bell-shaped float drain for Esco stainless steel versions Mounting the manometer 49

4 4 1 Introduction 1.1 General The present installation instructions are a supplement of the installation and operating instructions of the Condair Esco and describe the installation of the different steam distribution systems of the Condair Esco in a duct. The electrical connection of the valve actuators is not part of these installation instructions. 1.2 Safety Inappropriate installation of the steam distribution system may result in steam leakage during operation. Withdrawing steam may cause injury of person or damage of material assets. Therefore, please observe and comply with the following safety instructions and the information and safety instructions contained in the installation and operating instructions of the Condair Esco. The steam distribution system Condair Esco must only be installed by persons familiar with this product and sufficiently qualified for the task. All instructions in the present installation instructions must be followed and complied with. Original Condair accessories and options from your supplier must be used exclusively for installation of the steam distribution system Condair Esco. Without the written consent of the supplier, no attachments or modifications must be made to the steam distribution systems Condair Esco, accessories, and options. All local safety regulations concerning the use of pressurised steam systems must be followed complied with. It is assumed that all persons in charge with the installation of the steam distribution system are familiar and comply with the appropriate regulations on work safety and the prevention of accidents. The weight of some components of the steam distribution system is more than 20 kg. Therefore, always transport these components with the help of another person or use an appropriate lifting device. Always secure the components during installation against falling down. After the installation or during the initial start-up of the system all installations must be checked for tightness. Systems with leaky installations may not be taken in operation.

5 5 2 Esco DL Overview Esco DL40 Esco 5 cast iron Esco 10 cast iron Esco 20 cast iron >20 kg DL40-1 pipe DL40-2 pipes DL40-3 pipes Primary condensate drain Thermostatic steam trap Spheric float drain Bell-shaped float drain Secondary condensate drain Thermostatic steam trap Manometer

6 6 Esco 10 stainless steel Esco 20 stainless steel DL40-1 pipe DL40-2 pipes DL40-3 pipes Primary condensate drain Thermostatic steam trap Spheric float drain Bell-shaped float drain Secondary condensate drain Thermostatic steam trap Manometer

7 7 2.2 Mounting the Esco DL Mounting the Esco DL40 with one steam pipe 1. Fix drilling template supplied (self-adhesive), then drill holes. d1 d2 d3 Esco 5 Esco 10 Esco 20 ø9 mm ø13 mm ** ø45 mm ø45 mm ø65 mm ø13 mm 1/2 ** if mounting set for insulated ducts is used d1 d2 1/2 d1 d3 2. Mount valve unit. Remove protective plug from the connector flange of the valve unit. This step must be carried out only if mounting set for insulated ducts is used: Cut length of the supporting tubes to duct wall thickness L, then insert the tubes into the fixing holes. Fix valve unit to the duct as shown below using the screws, washers and nuts. Before tightening, centrically align the bores of the duct and the valve unit. Screws washers and nuts for non insulated ducts (by client) Esco 5 Esco 10 Esco 20 1 M8 x * (Wrench size 13 mm) 2 ø24/8.4 x 2 mm 3 M8 x 0.8d * length as required Mounting set for insulated ducts L L Esco 5 Esco 10 Esco 20 1 M8 x 70 mm **/ M8 x 100 mm ** Wrench size 13 mm 2 ø24/8.4 x 2 mm 3 ø12/8.5 x 45 mm **/ ø12/8.5 x 100 mm ** 4 M8 x 0.8d Correct installation position Esco 5: Writing must be readable ** as ordered

8 8 3. Mounting the steam pipe. Remove protective caps from the steam pipe. From the inside of the duct push the steam pipe into the valve unit until it comes to a stop (the resistance of the O-ring inside the valve unit must be overcome). The steam pipe is installed correctly, if the secondary condensate drain pipe pokes X mm out of the duct (see illustration and table below). Note: To improve gliding ability moisten the end of the steam pipe and the O-ring inside the valve unit with water (do not use oil or grease!). Water X Esco 5 Esco 10 Esco 20 X 30 mm 24 mm 50 mm 4. Fix steam pipe. Horizontally align steam pipe using a spirit level, then fix the end of the steam pipe to the duct wall or the duct ceiling (by client). Screw M5x6 grub screws (allen key 2.5 mm) provided on both sides into the valve unit, until they touch the steam pipe.

9 9 5. Seal the bores inside the duct with silicone-free sealant. 6. Connecting the steam supply line (see chapter 5.1). 7. Mounting the secondary condensate drain (see chapter 5.2). 8. Mounting the primary condensate drain (see chapter 5.3). 9. Mounting the manometer (see chapter 5.4).

10 Mounting the Esco DL40 with two/three steam pipes 1. Fix drilling template supplied (self-adhesive), then drill holes. Note: exclusively use the drilling template in the plastic bag attached to the collector pipe RevStd: Doppelkollektor Esco /xxx Double coupling Esco /xxx Raccord double Esco /xxx A d1 d2 B A d1 d3 d1 d2 d1 d3 d1 d2 d3 Esco 10 Esco 20 ø9 mm ø13 mm ** ø45 mm ø13 mm ** if mounting set for insulated ducts is used RevStd: Dreifachkollektor Esco /xxx Threefold coupling Esco /xxx Raccord triple Esco /xxx A d1 d2 B d1 d3 d1 d2 B A d1 d3 d1 d2 d1 d3

11 11 2. Mount collector pipe. Remove protective plugs from the steam connectors of the collector pipe. This step must be carried out only if mounting set for insulated ducts is used: Cut length of the supporting tubes to duct wall thickness L, then insert the tubes into the fixing holes. Fix collector pipe to the duct as shown below using the screws, washers and nuts. Before tightening, centrically align the bores of the duct and the collector pipe. Screws washers and nuts for non insulated ducts (by client) Esco 10 Esco 20 1 M8 x * (Wrench size 13 mm) 2 ø24/8.4 x 2 mm 3 M8 x 0.8d * length as required Mounting set for insulated ducts L L Esco 10 Esco 20 M8 x 70 mm **/ M8 x 100 mm ** 1 Wrench size 13 mm 2 ø24/8.4 x 2 mm 3 ø12/8.5 x 45 mm **/ ø12/8.5 x 100 mm ** 4 M8 x 0.8d ** as ordered

12 12 3. Mount steam pipes. Remove protective caps from the steam pipes. From the inside of the duct push the steam pipes into the connectors of the collector pipe until they come to a stop (the resistance of the O-ring inside the connectors of the collector pipe must be overcome). The steam pipes are installed correctly, if the secondary condensate drain pipe pokes 24 mm out of the duct. Note: To improve gliding ability moisten the end of the steam pipes and O-rings inside the connectors of the collector pipe with water (do not use oil or grease!). Water Water 24 mm Water Water Water 24 mm

13 13 4. Fix steam pipes. Horizontally align steam pipes using a spirit level, then fix the ends of the steam pipes to the duct wall or the duct ceiling (by client). Screw the M5x6 grub screws (allen key 2.5 mm) provided into the steam pipe connectors of the collector pipe (as shown below), until they touch the steam pipe.

14 14 5. Seal the bores inside the duct with silicone-free sealant.

15 15 6. Mount valve unit. Remove protective cap/plug from the valve unit and the collector pipe. Push valve unit onto the connector of the collector pipe until it comes to a stop (the resistance of the O-ring inside the valve unit must be overcome). Then, fix valve unit to the collector pipe as shown below using the screws, washers and nuts (wrench size 13 mm). Note: To improve the gliding ability moisten the steam connector of the collector pipe and the O-ring inside the valve unit with water (do not use oil or grease!). Water Water

16 16 7. Connecting the steam supply line (see chapter 5.1). 8. Mounting the secondary condensate drain (see chapter 5.2). 9. Mounting the primary condensate drain (see chapter 5.3). 10. Mounting the manometer (see chapter 5.4).

17 17 3 Esco DR Overview Esco DR73 Esco 10 cast iron Esco 20 cast iron Esco 30 cast iron >20 kg >20 kg DR73 A type DR73 B type Primary condensate drain Thermostatic steam trap Spheric float drain Bell-shaped float drain Secondary condensate drain Thermostatic steam trap Manometer

18 18 Esco 10 stainless steel Esco 20 stainless steel DR73 A type DR73 B type Primary condensate drain Thermostatic steam trap Spheric float drain Bell-shaped float drain Secondary condensate drain Thermostatic steam trap Manometer

19 Mounting the Esco DR73 A type 1. Fix drilling template supplied (self-adhesive), then drill holes. d1 Esco 10 Esco 20 Esco 30 ø9 mm ø13 mm ** ø13.5 mm ø17 mm ** d2 ø45 mm ø65 mm ø95 mm d3 ø13 mm ** if mounting set for insulated ducts is used d1 Esco 10 Esco 20 Esco 30 Z 160 mm 170 mm 170 mm U Distance between bottom edge of the duct up to the highest point of the duct floor d2 Z d1 d3 U

20 20 2. Mount valve unit. Important: if the collector pipe is mounted before the valve unit, steps 3 to 6 must be done first. Remove protective plug from the steam pipe connector of the valve unit. This step must be carried out only if mounting set for insulated ducts is used: Cut length of the supporting tubes to duct wall thickness L, then insert the tubes into the fixing holes. Fix valve unit to the duct as shown below using the screws, washers and nuts. Before tightening, centrically align the bores of the duct and the valve unit. Screws washers and nuts for non insulated ducts (by client) Mounting set for insulated ducts L L Esco 10 Esco 20 Esco 30 1 M8 x * M12 x * Wrench size 13 mm Wrench size 19 mm 2 ø24/8.4 x 2 mm ø37/13 x 3 mm 3 M8 x 0.8d M12 x 0.8d * length as required Esco 10 Esco 20 Esco 30 1 M8 x 70 mm ** M8 x 100 mm ** Wrench size 13 mm M12 x 70 mm ** M12 x 100 mm ** Wrench size 19 mm 2 ø24/8.4 x 2 mm ø37/13 x 3 mm 3 ø12/8.5 x 45 mm ** ø16/13 x 45 mm ** ø12/8.5 x 100 mm ** ø16/13 x 70 mm ** 4 M8 x 0.8d M12 x 0.8d ** as ordered

21 21 3. Mount collector pipe. Remove protective caps from the collector pipe. If the valve unit is already mounted: from the inside of the duct push the collector pipe into the valve unit until it comes to a stop (the resistance of the O-ring inside the valve unit must be overcome). The collector pipe is installed correctly, if the secondary condensate drain pipe pokes X mm out of the duct (see illustration and table below). Note: To improve gliding ability moisten the end of the collector pipe and the O-ring inside the valve unit with water (do not use oil or grease!). Water X Esco 10 Esco 20 Esco 30 X 24 mm 50 mm 50 mm

22 22 If the valve unit is not mounted yet: from the inside of the duct push the collector pipe and the secondary condensate drain pipe through the corresponding bores in the duct wall until the end of the collector pipe pokes exactly T mm out of the duct (see table below). D T Esco 10 Esco 20 Esco 30 D 41.0 mm 59.5 mm 88.0 mm T 69 mm 95 mm 95 mm

23 23 4. Fix collector pipe. Important: if the valve unit is not mounted yet, make sure the end of the collector pipe pokes exactly T mm out of the duct (see table in step 3) before fixing the collector pipe. Horizontally align collector pipe using a spirit level, then fix the end of the collector pipe with the bracket supplied to the duct floor or with the optional wall support to the duct wall. Screw M5x6 grub screws (allen key 2.5 mm) provided on both sides into the valve unit, until they touch the steam pipe.

24 24 5. Seal the bores inside the duct with silicone-free sealant.

25 25 6. Mount vertical steam distribution pipes. Remove protective plugs from the sockets of the collector pipe. Push vertical steam distribution pipes into the sockets of the collector pipe until they come to a stop (the resistance of the O-rings inside the sockets must be overcome). Then, align nozzle apertures to the air flow according to drawing below. Note: To improve the gliding ability moisten the end of the vertical steam pipes and the O-rings inside the collector sockets with water (do not use oil or grease!). Screw the M5x6 grub screws (allen key 2.5 mm) provided into the sockets (as shown below), until they touch the vertical steam distribution pipes. Vertical steam distribution pipes with a length >1400 mm must be fixed to the duct ceiling using the brackets supplied. Before tightening the brackets vertically align steam pipes using a spirit level. L> 1400 mm L Water air flow direction Air flow direction >200 mm >200 mm <200 m <200 mm

26 26 7. Connecting the steam supply line (see chapter 5.1). 8. Mounting the secondary condensate drain (see chapter 5.2). 9. Mounting the primary condensate drain (see chapter 5.3). 10. Mounting the manometer (see chapter 5.4). 3.3 Mounting the Esco DR73 B type 1. Fabricate collector supporting sheet (by client). Cut collector supporting sheet (L= as required, B= 20 mm more than flange width or flange outer diameter of the valve unit used) Mark holes on the collector supporting sheet using the template supplied, then drill holes. Holes d4 must not be drilled until the collector supporting sheet is fixed to the duct. B d4 L d2 d1 d3 Esco 10 Esco 20 Esco 30 d1 ø9 mm ø13.5 mm d2 ø45 mm ø65 mm ø95 mm d3 ø13 mm

27 27 2. Mark holes on the duct floor, then drill holes. Measure dimensions LX, C, da and BX (thickness of the collector supporting sheet). Mark holes according to the illustration below, then drill holes. Esco 10 Esco 20 Esco 30 T 69 mm ** 95 mm ** 95 mm ** DX C db Distance between the first bore to the outer wall of the duct DX= LX-T-BX Distance according measurement Diameter of the bores db= da+2 mm ** imperatively observe the dimensions indicated DX D T BX db DX C C C U2 U2 max: <36 mm BX Esco 10 Esco 20 Esco 30 D 41.0 mm 59.5 mm 88.0 mm T 69 mm 95 mm 95 mm da T LX

28 28 3. Fix collector pipe to the duct floor using self-tapping screws. Caution! Until the definite supports are installed (step 4) the collector pipe must be secured with auxiliary supports against falling down. 4. Mount supports. Remove protective plugs from the steam pipe connector and the condensate pipe connector. Slide supporting sheet onto the collector pipe and fix it to the duct wall using two self-tapping screws (check dimension T ). Fabricate a support in order to support the angled end of the collector pipe (by client), then mount the support. Note: for collector pipes with more than 10 vertical steam distribution pipes an additional support must be mounted in the middle of the collector pipe. Esco 10 Esco 20 Esco 30 T 69 mm ** 95 mm ** 95 mm ** ** imperatively observe the dimensions indicated T

29 29 5. Mount valve unit. Remove protective plug from the valve unit. Push valve unit onto the steam pipe until it comes to a stop (the resistance of the O-ring inside the valve unit must be overcome). Then, fix valve unit to the supporting sheet as shown below using two screws, washers and nuts each. Note: To improve the gliding ability moisten the steam connector of the collector pipe and the O-ring inside the valve unit with water (do not use oil or grease!). Screw the M5x6 grub screws (allen key 2.5 mm) provided on both sides into the valve unit (as shown below), until they touch the steam pipe. Esco 10 Esco 20 Esco 30 M8 x 35 Wrench size 13 mm M12 x 35 Wrench size 19 mm Water

30 30 6. Mount vertical steam distribution pipes. Remove protective plugs from the sockets of the collector pipe. Push vertical steam distribution pipes into the sockets of the collector pipe until they come to a stop (the resistance of the O-rings inside the sockets must be overcome). Then, align nozzle apertures to the air flow according to drawing below. Note: To improve the gliding ability moisten the end of the vertical steam pipes and the O-rings inside the collector sockets with water (do not use oil or grease!). Screw the M5x6 grub screws (allen key 2.5 mm) provided into the sockets (as shown below), until they touch the vertical steam distribution pipes. Vertical steam distribution pipes with a length >1400 mm must be fixed to the duct ceiling using the brackets supplied. Before tightening the brackets vertically align steam pipes using a spirit level. L> 1400 mm L Water Air flow direction Air flow direction >200 mm >200 mm <200 m <200 mm

31 31 7. Connecting the steam supply line (see chapter 5.1). 8. Mounting the secondary condensate drain (see chapter 5.2). 9. Mounting the primary condensate drain (see chapter 5.3). 10. Mounting the manometer (see chapter 5.4).

32 32 4 Esco DR73 J 4.1 Overview Esco DR73 J Esco 20 cast iron Esco 20 stainless steel Esco 30 cast iron >20 kg >20 kg DR73 JA Left DR73 JA Right DR73 J2A Left Right DR73 J2A Right Middle DR73 J2A Left Middle Primary condensate drain Spheric float drain Bell-shaped float drain Secondary condensate drain Thermostatic steam trap Manometer

33 Mounting the Esco DR73 J (Jumbo) 1. Fix drilling template supplied (self-adhesive), then drill holes (illustration below shows DR73 J2A Left Right). Note: Dimensions for the placement of the drilling templates see following hole pattern. XX d1 XX Z d2 d1 YY d1 U = = d3 d2 d1 these holes must not be drilled! d1 Esco 20 Esco 30 ø9 mm ø13 mm ** ø13.5 mm ø17 mm ** d2 ø65 mm ø95 mm d3 ø13 mm ** if mounting set for insulated ducts is used

34 34 Hole pattern DR73 JA Right (dimensions in mm) Front view XX Top view Z 140 YY/2 N YY YY/2 ø13 ø95 80 øa XX YY Hole pattern DR73 J2A Link Right (dimensions in mm) Front view XX XX Top view N øa ø95 80 YY YY/2 YY/2 ø Z Internal dimension of duct XX XX YY ø13 U U Hole pattern DR73 JA Left (dimensions in mm) Front view Top view XX N øa ø95 80 ø13 YY YY/2 YY/2 140 Z Internal dimension of duct XX YY U Internal dimension of duct

35 35 Hole pattern DR73 J2A Left Middle (dimensions in mm) Front view Top view XX N øa ø95 80 ø13 ø95 YY YY/2 YY/2 140 Z Internal dimension of duct XX YY U Hole pattern DR73 J2A Right Middle (dimensions in mm) Front view Top view XX N Internal dimension of duct Z 140 YY/2 ø95 YY YY/2 ø13 ø95 80 øa U XX YY Esco 20 Esco 30 N (Collector) XX ** YY ** YY/2 ** Z a U 120 x 120 mm 220 mm 190 mm 95 mm 170 mm ø9 mm (ø13 mm ***) 100 x 100 mm 250,5 mm 170 mm 85 mm 170 mm ø13.5 mm 120 x 120 mm 260,5 mm 190 mm 95 mm 170 mm (ø17 mm ***) Distance between bottom edge of the duct to the highest point of the duct floor ** customised versions with deviating dimensions XX and YY possible *** if mounting set for insulated ducts is used

36 36 2. Mount valve unit. Important: if the collector pipe is mounted before the valve unit(s) is(are) fixed, steps 3 to 6 must be done first. Remove protective plug from the connector flange(s) of the valve unit(s). This step must be carried out only if mounting set for insulated ducts is used: Cut length of the supporting tubes to duct wall thickness L, then insert the tubes into the fixing holes. Fix valve unit(s) to the duct as shown below using the screws, washers and nuts. Before tightening, centrically align the bores of the duct and the valve unit. Screws washers and nuts for non insulated ducts Mounting set for insulated ducts L L (by client) Esco 20 Esco 30 1 M8 x * M12 x * Wrench size 13 mm Wrench size 19 mm 2 ø24/8.4 x 2 mm ø37/13 x 3 mm 3 M8 x 0.8d M12 x 0.8d * length as required Esco 20 Esco 30 1 M8 x 70 mm ** M8 x 100 mm ** Wrench size 13 mm M12 x 70 mm ** M12 x 100 mm ** Wrench size 19 mm 2 ø24/8.4 x 2 mm ø37/13 x 3 mm 3 ø12/8.5 x 45 mm ** ø16/13 x 45 mm ** ø12/8.5 x 100 mm ** ø16/13 x 70 mm ** 4 M8 x 0.8d M12 x 0.8d ** as ordered

37 37 3. Mount collector pipe (illustration below shows DR73 J2A Left Right). Remove protective caps from the collector pipe. If the valve unit(s) is(are) already mounted: from the inside of the duct push the connector(s) of the collector pipe into the valve unit(s) until it/they come(s) to a stop (the resistance of the O-ring inside the valve unit(s) must be overcome). The collector pipe is installed correctly, if the secondary condensate drain pipe pokes 50 mm out of the duct (see illustration below). Note: To improve gliding ability moisten the end/ends of the collector pipe connector(s) and the O-ring(s) inside the valve unit(s) with water (do not use oil or grease!). Water Water 50 mm

38 38 If the valve unit(s) is(are) not mounted yet: from the inside of the duct push the connector(s) of the collector pipe and the secondary condensate drain pipes through the corresponding bores in the duct wall until the connector(s) of the collector pipe poke(s) exactly T mm out of the duct (see table below). Esco 10 Esco 20 Esco 30 D 41.0 mm 59.5 mm 88.0 mm T 69 mm 95 mm 95 mm D T D T

39 39 4. Fix collector pipe (illustration below shows DR73 J2A Left Right). Important: if the valve unit(s) is(are) not mounted yet, make sure the connector(s) of the collector pipe poke(s) exactly T mm out of the duct (see table in step 3) before fixing the collector pipe. Horizontally align collector pipe using a spirit level, then fix the end of the collector pipe with the brackets supplied to the duct floor or with the optional wall support to the duct wall. Screw the M5x6 grub screws (allen key 2.5 mm) provided on into the flange pipe of the valve unit, until they touch the steam pipe.

40 40 5. Seal the bores inside the duct with silicone-free sealant.

41 41 6. Mount vertical steam distribution pipes. Remove protective plugs from the sockets of the collector pipe. Push vertical steam distribution pipes into the sockets of the collector pipe until they come to a stop (the resistance of the O-rings inside the sockets must be overcome). Then, align nozzle apertures to the air flow according to drawing below. Note: To improve the gliding ability moisten the end of the vertical steam pipes and the O-rings inside the collector sockets with water (do not use oil or grease!). Screw the M5x6 grub screws (allen key 2.5 mm) provided into the sockets (as shown below), until they touch the vertical steam distribution pipes. Vertical steam distribution pipes with a length >1400 mm must be fixed to the duct ceiling using the brackets supplied. Before tightening the brackets vertically align steam pipes using a spirit level. L> 1400 mm L Air flow direction <200 mm <200 mm Air flow direction >200 m >200 mm

42 42 7. Connecting the steam supply line (see chapter 5.1). 8. Mounting the secondary condensate drain (see chapter 5.2). 9. Mounting the primary condensate drain (see chapter 5.3). 10. Mounting the manometer (see chapter 5.4).

43 43 5 Mounting the steam supply line, the primary and secondary condensate and the manometer 5.1 Connect the steam supply line (by client) Note: the steam supply line must be made according to the instructions in chapter 5 of the installation and operating instructions of the Condair Esco. Steam supply lines with a length of more than 4 m between the branch connection of the main steam line and the connecting flange of the valve unit must mandatory be drained. Esco 5 G 1/2" wrap teflon tape around the thread or apply silicone-free sealant (heat-resistant up to 155 C)

44 Mounting the secondary condensate drain Wrap teflon tape around the thread of the angled screw coupling or apply silicone-free sealant (heat-resistant up to 155 C). Then, screw angled screw coupling into the secondary condensate drain (arrow on the thermostatic steam trap must point in drain direction). Slide angled screw coupling onto the condensate pipe until it comes to a stop. Tighten union nut so far, that the angled screw coupling can not be turned by hand anymore. The outlet of the secondary condensate drain must be connected to the drain line of the building via an open funnel (pressure-free draining) with siphon (by client). Thermostatic steam trap stainless steel Wrench size 22 mm wrap teflon tape around the thread or apply silicone-free sealant (heat-resistant up to 155 C) admissible mounting position Wrench size 32 mm not admissible mounting position Rp 1/2" Thermostatic steam trap brass admissible mounting position Wrench size 19 mm wrap teflon tape around the thread or apply silicone-free sealant (heat-resistant up to 155 C) not admissible mounting position Rp 1/2" 5.2.1

45 Mounting the primary condensate drain Important notes The primary condensate must be discharged separately from the secondary condensate. The primary condensate can either be discharged pressure-free or with a maximum back-pressure of 1/2 of the primary steam pressure. The discharge/feedback of the primary condensate is customers responsibility Thermostatic steam trap for Esco cast-iron and stainless steel versions Wrap teflon tape around the threads of the threaded pipe or apply silicone-free sealant (heatresistant up to 155 C). Then, screw threaded pipe into the primary condensate drain (arrow on the condensate drain must point in drain direction). Remove protective plug from the condensate connector of the valve unit, then screw threaded pipe from the bottom into the valve unit. wrap teflon tape around the thread or apply silicone-free sealant (heat-resistant up to 155 C) Flow direction Wrench size 32 mm Rp 1/2" admissible mounting position not admissible mounting position

46 Spheric float drain for Esco cast-iron version Wrap teflon tape around the thread of the fitting or apply silicone-free sealant (heat-resistant up to 155 C). Then, screw fitting into the spheric float drain (arrow on the spheric float drain must be on top and point in drain direction). Remove protective plug from the condensate connector of the valve unit, then fix spheric float drain to the valve unit using the banjo bolt and the copper rings. wrap teflon tape around the thread or apply silicone-free sealant (heat-resistant up to 155 C) Wrench size 24 mm Wrench size 22 mm Arrow on the type plate must point downwards Wrench size 27 mm Rp 1/2" Flow direction Bell-shaped float drain for Esco cast-iron version Wrap teflon tape around the thread of the fitting or apply silicone-free sealant (heat-resistant up to 155 C). Then, screw fitting into the bell-shaped float (arrow on the bell-shaped float must be on top and point in drain direction). Remove protective plug from the condensate connector of the valve unit, then fix bell-shaped float to the valve unit using the banjo bolt and the copper rings. Wrench size 24 mm Wrench size 22 mm wrap teflon tape around the thread or apply siliconefree sealant (heat-resistant up to 155 C) Flow direction Wrench size 27 mm Rp 1/2"

47 Spheric float drain and bell-shaped float drain for Esco stainless steel versions Attention danger of mistake: the stainless steel spheric float drain can easily be mistaken with the stainless steel bell-shaped float drain. A mistake of the two floats leads to a malfunctioning during operation, since the two floats have different installation positions. Spheric float drain made of stainless steel Bell-shaped float drain made of stainless steel correct installation position Characteristics of the spheric float drain: Designation TOP (on top) plug screw (on the bottom) wrong installation position Spheric float drain for Esco stainless steel versions Wrap teflon tape around the thread of the straight fitting or apply silicone-free sealant (heatresistant up to 155 C). Then, remove protective plug from the condensate connector of the valve unit screw fitting into the valve unit. Wrap teflon tape around the thread of the angled screw coupling or apply silicone-free sealant (heat-resistant up to 155 C). Then, screw angled screw coupling into the spheric float drain as shown below (the union nut must point to the marking TOP and the arrow on the spheric float drain must point in drain direction). Slide angled screw coupling with the spheric float drain onto the straight fitting until it comes to a stop. Tighten union nut so far, that the spheric float drain can not be turned by hand anymore. tighten screws after alignment! flow direction Rp 1/2" Wrench size 22 mm Wrench size 24 mm wrap teflon tape around the thread or apply silicone-free sealant (heat-resistant up to 155 C)

48 Bell-shaped float drain for Esco stainless steel versions Wrap teflon tape around the thread of the straight fitting or apply silicone-free sealant (heatresistant up to 155 C). Then, remove protective plug from the condensate connector of the valve unit screw fitting into the valve unit. Wrap teflon tape around the thread of the angled screw coupling or apply silicone-free sealant (heat-resistant up to 155 C). Then, screw angled screw coupling into the bell-shaped float drain as shown below (the union nut must point to the top and the arrow on the bell-shaped float drain must point in drain direction). Slide angled screw coupling with the bell-shaped float drain onto the straight fitting until it comes to a stop. Tighten union nut so far, that the bell-shaped float drain can not be turned by hand anymore. Wrench size 22 mm Wrench size 24 mm wrap teflon tape around the thread or apply silicone-free sealant (heat-resistant up to 155 C) Flow direction Rp 1/2"

49 Mounting the manometer Wrap teflon tape around the thread or apply silicone-free sealant (heat-resistant up to 155 C)

50 Notes

51 Condair Ltd., Printed in Switzerland Technical modifications reserved

52 CONSULTING, SALES AND SERVICE: Reg.No Manufacturer: Condair Ltd. Member of the Walter Meier Group Talstrasse 35-37, 8808 Pfäffikon, Switzerland Ph , Fax