Service Information. HOTPOINT SIDE-BY-SIDE FRIDGE FREEZERS (7 ~ Segment Version) Indesit Company UK Ltd

Size: px
Start display at page:

Download "Service Information. HOTPOINT SIDE-BY-SIDE FRIDGE FREEZERS (7 ~ Segment Version) Indesit Company UK Ltd"

Transcription

1 Issue 2 March 2011 HOTPOINT SIDE-BY-SIDE FRIDGE FREEZERS (7 ~ Segment Version) Models Covered Comm. Code Energy Band 'A' Models MSZ801DF MSZ802DF MSZ803DF MSZ806DF Service Information Indesit Company UK Ltd 2011 Reg. Office: Peterborough PE2 9JB Registered in London:

2 HEALTH AND SAFETY For the servicing of refrigeration products, containing R134a refrigerant. These instructions are in addition to any other Company procedures already published. Published primarily for Indesit Company engineers working in the UK or Southern Ireland, for which these instructions are MANDATORY. General 1. This manual is not intended as a comprehensive repair/maintenance guide to the appliance. 2. It should only be used by suitably qualified persons having technical competence, applicable product knowledge, suitable tools and test equipment. 3. Servicing of electrical appliances must be undertaken with the appliance disconnected. (unplugged from the electrical supply). 4. Servicing must be preceded by earth continuity and insulation checks. 5. Personal safety precautions must be taken to protect against accidents caused by sharp edges on metal and plastic parts. 6. After servicing, the appliance must be rechecked for electrical safety. Refrigerant R134a - Safe Handling - Transporting & Storage 1. Work areas should be well ventilated and any immediate heat sources turned off. 2. Do not smoke where there is a possibility of refrigerant in the atmosphere. Customer/s should also be advised. 3. Cylinders must not have heat applied, or stand close to a heat source, and should be stored out of direct sunlight. 4. Should a sudden release of refrigerant occur, open windows or outside doors in the immediate vicinity, then evacuate for a few minutes. 5. It is illegal to intentionally vent R134a refrigerant to atmosphere. Follow the company procedure on collection and reclamation. 6. If a leak is identified the appliance must be repaired immediately if possible. 7. Where it is not possible to repair the appliance immediately the customer should be advised: Appliance should be turned off and the refrigerant recovered. 8. Returned compressors must be sealed to prevent the escape of oil and refrigerant. Refer to the Environmental responsibilities for service engineers in your Health and Safety booklet. 9. Cylinders (R134a) being transported must be in an upright position on the floor of the vehicle and prevented from movement. 10. A green compressed gas label Part No should be displayed on the rear of the vehicle. 2 of 37

3 CONTENTS Health & Safety Index & Serial Number / Product Identity Introduction Specifications Appliance Dimensions & Water Filter Detailed View Control Panel Interface Description of Functions Component Functions Temperature Tables Alarm Conditions Auto-Test and Fault Conditions Air Flow Ice-Maker Function and Adjustment Power Module Parameters Servicing & Dismantling Instructions Compressor Connection Chart Power Module Edge Connections Connector Block Chart Theoretical Wiring Diagram Thermistor Sensor Location Installation Instructions PRODUCT IDENTITY Example 1 Industrial Code: Serial Number: Printed on a separate label below the Rating Plate Build number that day, e.g th built Day of manufacture, e.g. 03 rd of month Month of manufacture, e.g. May Year of manufacture, e.g of 37

4 MODEL INTRODUCTION The models included in this publication are 1765 mm high Side by Side no-frost Fridge Freezers that were introduced in July All models are similar with regard to the furniture design, but there are variations for exterior colour. Models MSZ801DF, MSZ802DF, MSZ803DF and MSZ806DF interior: The interior of the fridge has safety glass shelves, one meat drawer (chiller) and one humidity controlled salad bin (crisper) with a glass cover. The door has two deep shelf, dairy shelf with a lid, a commodity shelf and lower bottle shelf. The interior of the freezer section has two drawers of varying sizes, two safety glass shelves of varying sizes and ice cube maker. The door has four commodity shelves of varying sizes. For banding and colour information, refer to the Front Cover and or Specifications page. The appliance is no-frost design so defrosting is automatic. All models have wheels at the rear and wheels / adjustable feet at the front. The digital display interface module (7 ~ segment LED) is mounted in the front of the freezer door with the drinks dispenser, the fast freeze button and ice maker controls are also mounted in the same area. The fridge and freezer temperature settings are adjusted by selecting the + / - buttons next to the relevant temperature display window. All functions are monitored and actioned by the power module mounted at the rear of the appliance within the compressor compartment. The climate class is N / ST signifying that it is designed to operate in ambient temperatures between +16 C to +38 C. As with many refrigeration appliances, it is important that it is installed and operated within the recommended ambient temperature range and that there is adequate ventilation. All appliances equipped with an automatic ice-maker and water dispenser must be connected to a water supply that only delivers drinking water. See specification page for pressure requirements. 4 of 37

5 SPECIFICATIONS Introduction Date Colours June 2007 July 2007 July 2008 Polar White MSZ801DF Silver MSZ802DF Stainless Steel MSZ803DF Black MSZ806DF Suffix 'DF' = dispenser models GENERAL: Manufactured in: Italy Appliance Type: Side by Side Static / No- Frost: No-Frost Door Hinging - Freezer L/H & Fridge R/H Reversible: No Plug/Cable: UK / 1.6m Water Pipe: 1.65m Noise Level: 'A' band models ~ 45dB Climate Class: (Rating Plate) N.ST = 16 C to 38 C Refrigeration Type: No-Frost - Fin On Tube (FOT) DIMENSIONS & WEIGHT: Height: 1774 mm Width: 902 mm Depth: 752 mm To allow product handling and sufficient air circulation, leave at least 10 mm clearance at the sides, above the appliance and between the rear panel and the wall. Weight Gross: 146 kg Weight Net: 140 kg CAPACITIES / VOLUME: Gross Volume Net Volume Fridge: 340 litre 335 litre Freezer: 206 litre 155 litre Freezing Capacities 24 hrs 12 kg Conservation Time 5 hours 5 of 37

6 TECHNICAL DATA: Power Supply Voltage: Power Supply Frequency: Mains Water Supply: Freezer Lamp: Dispenser Lamp: Fridge Lamp (Blue Light): 220/240 V 50 Hz Min. 1.7 bar Max. 8.1 bar E27 40W 220V - 240V E14 10W V T-Click 40W 220V - 240V ENERGY Energy Class: Power Consumption: Annual Consumption: A 1.39 kwh/24hr kwh/yr COMPRESSOR WINDING Manufacturer: Type I/D: Winding Resistance Start: Run: Refrigerant/ Grams: Insulation: Embraco EGYS 90 HLP R134a / 160g - Refer to the appliance rating plate C-Pentane HEATER RESISTANCES Evaporator Defrost Heater: 8.57 k COMPONENT RESISTANCES Condenser Fan Motor: Evaporator Fan Motor: Water Dispenser Solenoid Valve: Water Ice Maker Solenoid Valve: 4.49k 2.35k 8.68k 8.71k 6 of 37

7 APPLIANCE DIMENSIONS (all measurements are approximate) APERTURE MEASUREMENTS PLAN VIEW (WITH DOORS OPEN 90 AND FULLY) Cabinet Height = 1760 mm Cabinet Height with doors = 1765 mm Depth including door handles: 605 mm mm = 750 mm Depth without doors = 605 mm Depth without handles: 605 mm mm = 715 mm WATER FILTER 1. Locate the water filter cartridge cap below the freezer compartment door. Rotate the cap counter clockwise to a vertical position and pull the cap and filter cartridge out through the base grille. Note: Since there is water in the cartridge, some spilling may occur. 2. Remove the cartridge cap by sliding it off the end of the old cartridge. DO NOT DISCARD THE CAP. 3. Take the new cartridge out of its packaging and remove the protective cover from the o-rings. Make a note of the installation date in the space provided on the new cartridge. 4. Slide the cartridge cap onto the new cartridge. 5. With the cartridge cap in the vertical position, push the new filter cartridge into the base grille until it stops. Rotate the cartridge cap clockwise to a horizontal position. 6. RUN WATER THROUGH THE DISPENSER UNTIL THE WATER RUNS CLEAR (about 9-14 litres or 6-7 minutes). This will clean the system and clear air from the lines. Note: As air is cleared from the system, water may spurt out of the dispenser. 7 of 37

8 DETAILED VIEW R N T D A C S I O J B * S K L Q P M F H FE G REFRIGERATOR COMPARTMENT A. Inside light B*. Inside light (not fitted) C. Adjustable shelf D. Shelf - drawer lid E Crisper (Salad Bin) F. Crisper adjustment (Humidity Control) G. Meat / vegetable drawer (Chiller) H. Meat / vegetable drawer adjustment I. Dairy products compartment J. Door trays K. 2-litre door tray with bottle holder L litre door tray M. Water filter FREEZER COMPARTMENT N. Automatic ice-maker O. Glass shelves / Racks (depending on the model) P. Drawer / Bottom basket (depending on the model) Q. Drawer / Top basket (depending on the model) R. Ice cube drawer S. Freezer door trays T. Inside light 8 of 37

9 CONTROL PANEL INTERFACE TEMPERATURE CONTROL PANEL D A C B F G E BUTTON DESCRIPTION FUNCTION A Freezer temperature adjust / select ~ This function allows you to adjust the displayed temperature. To adjust the temperature press the relevant + / - button until the required freezer temperature is displayed on the left. B Super freeze ~ This function activates the super freeze (fast freeze) so fresh food can be frozen. To enable press until the super freeze symbol appears on the Display. It will automatically disable after 48 hours or when the button is pressed again. C Stand-by function ~ This function turns off the refrigerator and freezer compartments to enable press and hold for 3 seconds: the display will go out and a dash will appear on the left display. To disable press and hold for 3 seconds: the display will return to the previous set temperatures. D Reset ~ This function can be used in the event of an alarm when an acoustic signal and relevant indicator lights are activated. To disable the acoustic alarm signal press the reset button. E Fridge temperature adjust / select ~ This function allows you to adjust the displayed temperature. To adjust the temperature press the relevant + / - button until the required fridge temperature is displayed on the right. F Holiday function ~ This function allows the fridge compartment to be deactivated if the user is going away for sometime, the fridge will maintain adequate temperature for preventing the formation of odours, therefore not necessary to switch the appliance off. B+F Control panel Lock function (Child lock) ~ This function locks the fridge and freezer controls. To lock press and hold both the super freeze and super cool buttons simultaneously for 3 seconds until the lock symbol appears in the display and is accompanied by an acoustic signal. 9 of 37

10 CONTROL PANEL INTERFACE ICE & DISPENSER CONTROL PANEL H J K L BUTTON DESCRIPTION FUNCTION G Dispenser light ~ This function switches on the dispenser light. To enable / disable press the button. H Stand-by function ~ This function turns off the ice maker. To enable the ice maker press and hold until the ice or crushed ice symbol is displayed. To disable the ice maker press and hold until the ice or crushed ice symbol is extinguished. J Ice mode function ~ This function allows you to select between ice cubes or crushed ice to be dispensed. K Reset ~ This function resets the water filter replacement time. Normally the water filter symbol is Green (Blue on some models). = Water Filter OK (Blue on some models) = Water Filter requires replacing soon. = Water Filter needs replacing. L Ice maker lock ~ This function locks the ice maker and water dispenser controls. To lock press and hold for 3 seconds until the lock symbol appears in the display and is accompanied by an acoustic signal. To unlock press and hold for 3 seconds until the symbol is extinguished. 10 of 37

11 DESCRIPTION OF FUNCTIONS Super freeze function ~ This enables and controls the compressor, condenser fan and evaporator fan to cool down the freezer compartment independently of the temperature settings set by the user. The super freeze function will end automatically after 48 hours after activation. Freezer Temperature Freezer Door Alarm Fridge Door Alarm Fridge Temperature Holiday Function ~ This can be adjusted and selected by the + / - buttons in the freezer section of the control interface. For each press of the relevant button you will increase / decrease the temperature setting by 1 C increments. The range is from -18 C (-17 C some models) to -24 C. ~ The door alarm symbol lights up and the acoustic alarm is activated when the freezer door remains open. When the door is left open for more than 2 minutes, the symbol flashes and an acoustic signal sounds. ~ The door alarm symbol lights up and the acoustic alarm is activated when the fridge door remains open. When the door is left open for more than 2 minutes, the symbol flashes and an acoustic signal sounds. ~ This can be adjusted and selected by the + / - buttons in the fridge section of the control interface. For each press of the relevant button you will increase / decrease the temperature setting by 1 C increments. The range is from +2 C to +6 C. ~ This enables and controls the fridge damper (baffle) and evaporator fan for the holiday mode. The evaporator fan is activated and the fridge damper (baffle) is opened for only 2 minutes. This process is repeated every 30 minutes while the holiday function is enabled. 11 of 37

12 COMPONENT FUNCTIONS General Information The power module is made up of a number of smaller individual modules (sections), each one controlling a functional component. The modules are linked together when required to control a particular function or functions. The linking of the individual modules is optional and therefore allows for each module to be switched ON or OFF, this is determined from the data stored or collected by the modules and the results of module comparisons. The power module memory stores information such as temperatures and times. Having individual set of parameter values built in to it, directly aimed at providing the specific control needs for the physical and system characteristics of the model type. Fridge & Freezer Control The power module monitors the fridge and freezer air sensors, comparing their sensor resistance values with the cut-in and cut-out parameter values stored in its memory. Although the parameters are set, they allow for adjustment within those parameters so that the user has control. The results from the comparisons will determine if cooling is initiated, other circuits of the module will also use the results. The power module will enable normal operation provided there is no malfunction condition. Fridge or Freezer Malfunction Module The fridge or freezer malfunction module enables the appliance to continue operating in the unlikely hood of the fridge or freezer sensors failing. Pre-set timed functions stored in the modules memory is used to cycle cold request on and off. A malfunction occurs when the fridge or freezer cabinet sensors return a value to the module of either Open or Closed circuit, rather than a particular resistance value. Evaporator Fan Module The freezer fan is located above the evaporator coil and is designed to distribute the cold air produced by the evaporator coil uniformly inside the freezer compartment and when necessary in the fridge compartment. The freezer fan is managed by the module and is switched on/off after a preset time interval that is parameterised in the modules memory after a compressor start/stop. The fan will not operate when in the defrost cycle. After the defrost cycle the fan starts after a timed interval following a compressor start, this interval is also parameterised in the modules memory; this interval is different from the interval programmed for normal operating conditions. Electronic Motorised Damper Assembly (Baffle) The purpose of the damper is to allow the cold air produced by the evaporator to be distributed inside the refrigerator compartment. The damper is located in the top left hand (SX) corner of the fridge compartment. It is controlled by a fridge air sensor (thermistor) positioned in the centre of the rear wall of the fridge. Cold air from the evaporator is distributed in the refrigerator compartment. continued of 37

13 COMPONENT FUNCTIONS Compressor The compressor is managed by the power module and switches on whenever a demand for cooling is received. There are situations of cooling demand in which the compressor remains off. These are as follows: 1. Compressor protection: the compressor switches on once a minimum safety time lag has elapsed since the last power-off, thereby allowing the refrigerant gas pressure to reach a point of equilibrium in the refrigerant circuit. The same minimum safety time is observed in the event of a mains power interruption (voluntary or involuntary). This compressor protection strategy is observed only after the product has been operating continuously for the number of hours defined in the module memory. 2. Pause after defrost: at the end of the defrost cycle the compressor observes a protection time parameterised in the module memory so that the water formed during the defrost can be completely drained. 13 of 37

14 TEMPERATURE TABLES ON - OFF DAMPER TEMPERATURE TABLE REFRIGERATOR Temperature Sensor Refrigerator Display Damper (Baffle) ON ( C) Damper (Baffle) OFF ( C) Super Cool Any of the above FREEZER CONTROL TABLE FREEZER Temperature Sensor Freezer Display Compressor ON ( C) Compressor OFF ( C) Super Freeze Any of the above Continuous Run 14 of 37

15 ALARM CONDITIONS Control Panel Interface (mounted above dispenser assembly) Example above shows the ALARM 'd' flashing in the fridge temperature display. Check fridge Air Baffle (Damper) / Connections. TEMPERATURE DISPLAY ALARM CONDITION Freezer Fridge C Check freezer sensor / connections. Freezer too warm usually shown when turned on for the - - first time *. -9 C or warmer Temperature reached during a power cut *. Communication alarm between the control and display CF module. Check connections to both modules. Note: The appliance will run on default settings until fault is rectified. C Check fridge sensor / connections. d Check fridge air baffle (damper) / connections. ICON DISPLAY ALARM CONDITION Cubed Ice Crushed Ice Check fill valve ice maker solenoid and connections. * If the food has thawed out, it MUST NOT be refrozen. To turn the acoustic buzzer off during an alarm condition, press the reset button 'D' once. To restore the alarm condition back to normal operation proceed as follows: 1. Press the main RESET button (D). 2. Remove from the mains power. 3. Reconnect the main power. 15 of 37

16 AUTO TEST This helps with a quick check of the loads and sensors (thermistors), which otherwise are difficult to activate. NOTE: - Before using the AUTO-TEST it is advisable to check the correct operation of the temperature 7-segment LEDs (both fridge and freezer display), which are used for signalling possible malfunctions. Ensure the Super Freeze or Holiday modes have not been selected before starting the AUTO-TEST. SIDE X SIDE NO-FROST MODELS MSZ801DF (cc48862) MSZ802DF (cc46196) MSZ803DF (cc48863) MSZ806DF (cc57217) TO ACTIVATE STEP 1: If the appliance has been connected to the mains power for more than 15 minutes, disconnect it and wait 40 seconds before reconnecting it back to the mains supply. STEP 2: Wait until the display completes its set-up and returns to normal operation. STEP 3: Open the freezer door. STEP 4: Press the freezer light switch 3 times within 10 seconds. STEP 5: The test is activated when sequence '07' appears in the freezer temperature display. TO DEACTIVATE Manually: Switching OFF the power supply to the appliance. Sequence of check codes is indicated in the Freezer display (Sequence Duration) Sequence Code 07: (3 seconds) Evaporator Defrost Heater, Sequence Code 06: (3 seconds) Fridge Sensor, Sequence Code 05: (3 seconds) Freezer Sensor, Sequence Code 04: (3 seconds) Evaporator Fan, Sequence Code 02 to 00 flashing alternatively: (2.5 minutes) Baffle/damper triac Q3, Sequence Code 09: (3 seconds) Water Valve (Ice Maker), Sequence Code 12 to 00 flashing alternatively: (60 seconds) Ice Maker, Sequence Code 01 to 00 flashing alternatively: Water Valve (Washer Dispenser), NOTE: Confirm by pressing ice water dispenser pedal, Sequence Code 00: END. NOTE: Auto Test needs to be deactivated manually. See previous column. 16 of 37

17 Control Panel Interface (mounted above dispenser assembly) Example above shows Sequence '07' of the Auto Test in the freezer temperature display and fault code '7' to '0' flashing alternatively in the fridge temperature display. Check evaporator heater / connections. Fault conditions: are signalled to the engineer during Auto Test. See chart below for AUTO TEST fault codes and explanations. TEMPERATURE DISPLAY AUTO-TEST FAULT CODE Fridge (explanations) 8 to 0 flashing alternatively Relay K008 on module faulty (for Damper) 7 to 0 flashing alternatively 6 to 0 flashing alternatively Fridge Sensor (thermistor) 5 to 0 flashing alternatively Freezer Sensor (thermistor) 4 to 0 flashing alternatively Evaporator Fan 3 to 0 flashing alternatively Condenser Fan 2 to 0 flashing alternatively Damper (baffle) 9 to 0 flashing alternatively Water Valve for Icemaker H to 0 flashing alternatively Evaporator Defrost Heater - resistance can be obtained from power module 12PIN block term 1 & 16PIN block term 1 Icemaker (Sankyo) 1 to 0 flashing alternatively Water Valve for Water Dispenser Note: If two or more fault codes have been recognised, they will display alternately at 1 second intervals. 17 of 37

18 AIR FLOW COMPRESSOR AND CONDENSER COMPARTMENT The condenser fan is mounted at the rear near the compressor and draws air from the room through the right side of the front lower grille (A), through the condenser (B), around the compressor (C) where it exits out of the rear panel (D) but mainly passes over the dissipator to evaporate the defrost water (E) and finally exits out through the left side of the front lower grille. See image below: D C B E A THE ABOVE PROCESS IS REPEATED SO LONG AS THE CONDENSER FAN IS RUNNING. 18 of 37

19 AIR FLOW FRIDGE AND FREEZER INTERIOR COMPARTMENTS FREEZER The freezer evaporator is mounted just above the evaporator assembly (F). The fan draws air up through the evaporator where it is cooled (G) and blows into the top duct panel where it is channelled out through outlet ports (H). The air circulates around the freezer and returns through lower grille (J) and is drawn back up through the evaporator where the process is repeated. FRIDGE When there is a demand for cooling in the fridge, the damper (baffle) opens allowing cooled air from the freezer to enter via a ducting in the top left of the fridge (K). The air circulates around the fridge and returns to the freezer through the lower ducting (L). This process is repeated so long as the fridge damper is in the open position. MEAT / VEGETABLE DRAWER TEMPERATURE CONTROL SLIDER The cold air is conveyed inside the meat drawer through an adjustable opening between the fridge compartment and the freezer compartment. In this way the temperature inside the meat drawer is kept lower than the rest of the fridge. H K F G J L 19 of 37

20 THE SANKYO ICEMAKER HOW THE ICEMAKER WORKS Water is automatically measured into the icemaker mould by the inlet solenoid water valve. The Bi-metal thermostat mounted between the support housing and the mould detects the water / ice temperature. When the ice is cooled down to about - 9 C the thermostat switches the icemaker motor and the icemaker heater ON. The motor and the ejector blades begin to rotate. Because the ice is frozen hard in the mould the motor will stall the ejector blades as they apply pressure on the ice. During the stall period the heater warms the mould to loosen the ice. This may take a few (up to five) minutes. When the ice is loose enough, the ejector blades and the motor will complete the rotation and eject the ice from the mould. The ice collects in the ice bucket below the icemaker. The water inlet valve solenoid switches on again, to fill the mould with fresh water. NOTE: The Icemaker can only be checked with the 'Built-In Auto Test routine', see page of 37

21 POWER MODULE Parameters Parameter Values Stored in the Module Memory Direct the Appliance Operations - Parameters set in the module memory control the appliance functions. The minimum and maximum values for temperature are preset in the module memory. Sensors monitor temperature and the values are registered in the module. Where the sensor values are outside the presets a particular function will start or stop. Where a sensor fails, open or closed, the appliance operation will be controlled by time. The timed values for this are calculated in the module memory. The power module monitors door opening times and compressor run times. When the total of the door open and compressor run times are equal to or exceed the parameter values set in the memory, a defrost sequence will be initiated. COMPRESSOR OPERATION Compressor Operation - There are situations of cooling demand in which the compressor remains off. These are as follows: Compressor protection: the compressor switches on once a minimum safety time lag has elapsed since the last power-off, thereby allowing refrigerant gas pressure to reach a point of equilibrium in the refrigerant circuit. The same minimum safety time is observed in the event of a mains power interruption (voluntary or involuntary). Approximately 7 minutes Pause after defrost: at the end of the defrost cycle the compressor observes a protection time parameterised in the module memory so that the water formed during defrost can be completely drained. Approximately 7 minutes 21 of 37

22 POWER MODULE Parameters DEFROST HEATING ELEMENTS Defrost Heating Elements - The parameters utilised to start the defrost cycle are as follows: Compressor ON time since the last defrost cycle. 8 hours, but the start time will reduce dependant on door opening times. The appliance is plugged in and switched on. Total time since the last defrost cycle. 50 hours, but the start time will reduce dependant on door opening times. The parameters utilised to end the defrost cycle are as follows: Maximum time defrost heater is ON. Approximately 20 minutes Defrost end temperature (freezer defrost cut-out). +7 C ± 3 C FREEZER FAN OPERATION Freezer Fan Operation - The freezer fan is managed by the power module and is switched on/off after a preset time interval that is parameterised in the memory after a compressor start/stop. After the defrost cycle the fan starts after a timed interval following a compressor start, also this interval is parameterised in the memory; Compressor 7 minutes PLUS 3 minutes for the Fan = 10 minutes 22 of 37

23 SERVICING & DISMANTLING INSTRUCTIONS Before commencing any work refer to the Safety Notes at the beginning of this manual. All necessary precautions must be taken to prevent damage to the premises and the appliance. The appliance must be disconnected from the mains electricity supply. Where necessary, food and containers should be removed and stored according to the customer s requirements. A. FREEZER DOOR REMOVAL 1. Remove the lower plinth/grille (2 screws). 2. Disconnect the water tube that enters the bottom of the freezer door from the in-line connector. 3. Remove the top hinge cover (1 hex head screw). 4. Disconnect the 6-pin and 2-pin wiring connectors. 5. Remove 3 hex head screws securing the hinge, whilst supporting the door. 6. Ease the door from the cabinet and lift from the lower hinge without damaging the water tube. B. FRIDGE DOOR REMOVAL 1. Remove the lower plinth/grille (2 screws). 2. Remove the top hinge cover (1 hex head screw). 3. Remove 3 hex head screws securing the hinge, whilst supporting the door. 4. Ease the door from the cabinet and lift from the lower hinge. C. DOOR ALIGNMENT/ADJUSTMENT 1. Remove the top hinge cover (1 hex head screw). 2. Loosen the 3 hex head screws securing the hinge. 3. Adjust the alignment using the small adjustment screw. 4. Tighten the 3 hex head screws to secure the hinge. D. DOOR HANDLES 1. Remove the single screws securing the handle end cap mouldings at each end. 2. Remove the end cap mouldings from the tubular handle grip. These are very tight. E. ICEMAKER 1. Remove the ice cube bin. 2. Remove the one screw on the underside front of the icemaker. 3. Slide the icemaker forward and away from its support cradle. 4. The connector is embedded in the sidewall at the end of the icemaker; access can be gained after removing a black sponge block protecting it. F. AUGER & SOLENOID 1. Remove the ice cube bin and freezer shelving. 2. Remove the 4 screws (1 at each corner) securing the auger motor and solenoid assembly to the side mouldings. 3. Ease the unit forward and reach in to release the connector from the right hand (DX) sidewall. 23 of 37

24 G. FREEZER LAMP COVER & LAMP 1. Squeeze the sides inward and down. The front location tab can then be unhooked from its slot. 2. The lamp has two spade terminations and can be pulled out. H. FREEZER REAR PANELS (EVAPORATOR COVERS) 1. Remove the icemaker as in E and its support cradle. 2. Remove the auger and solenoid assembly as in F. 3. Remove all sidewall runners and fittings (except senor probe cover). Note which way up the runners are attached to the sidewall. 4. Remove the top section of the rear panel (2 screws). 5. Remove both lower rear panel sections together (6 screws) to expose the evaporator - (foil insulation behind the sections joins them together). On reassembly, ensure that the foil insulation is stuck down properly. J. EVAPORATOR FAN MOTOR 1. Remove the components as in E, F, G, and H. 2. Remove the fan blade. 3. Lift the motor to release the front retaining plastic moulding from its location. 4. Release the rear retaining plastic moulding to release the motor completely. 5. Disconnect the 2-pin connector. K. FAN MOTOR (Gain access for testing defrost heater, fan motor and cut-out) 1. Remove the 2 bottom screws of the middle rear panel. 2. Using a chisel knife or similar tool ease the bottom edge of the panel away from the foam pad stuck behind it. 3. Lift the bottom edge forward so the panel is approximately at Slide the panel forward along the side runners. 5. Disconnect the 2-pin connector for the fan motor. 6. Remove the two screws securing the plastic housing to the rear wall. 7. Lift the assembly from the evaporator metal heat shield. L. EVAPORATOR 1. Remove the components as in E, F, G, H and K. 2. Lift the evaporator metal heat shield upward slightly to release it from the retaining clip on the rear wall. Note: It is important to relocate in the clip properly on reassembly. 3. Disconnect the 6-pin connector above the evaporator and the earth connection to the metal heat shield. Note: Ensure that the earth connection is relocated properly on reassembly. 4. Pull the bottom of the evaporator outward and raise upward to remove the heat shield from the evaporator. Note: 2 metal clips which are not easy to see, hold the heat shield to the bottom run of the evaporator. These can fall out as the heat shield is removed. The metal clips are best refitted as follows: Before refitting the heat shield, locate the 2 clips correctly in their respective positions inside the heat shield, toward the bottom. As the heat shield is pushed into place over the evaporator, the clips should relocate in position on the bottom run of the evaporator tube. continued of 37

25 M. DEFROST HEATER (See K for testing purposes) 1. Remove the components as in E, F, G and H. 2. Disconnect the two connections to the heater. 3. Remove the components as in K. 4. Push the heater upward out of its retaining clips, the clips can now be removed completely and the heater withdrawn from the evaporator. N. THERMAL CUT-OUT 1. Remove the components as in K1 to 4, to gain access. Note: The thermal cut-out is supported by a plastic moulding at each side and is located at the top of the evaporator pipe. The plastic moulding must always be positioned in this way. NOTE: The pipe that the cut-out and plastic support is mounted to must be 30 mm above the top fins of the evaporator. P. COMPRESSOR HOUSING COVER PANEL 1. Remove the hex head screw securing the cover. 2. Keep the panel upright and manoeuvre upward to release from two locating plates at the bottom. Note: This can be awkward because the cover has a lip that fits under the rear of the appliance. Q. COMPRESSOR TERMINAL BOX 1. Cover pushes downward to fit. It can be removed by applying pressure in an upward direction at the lower edge of the black cover, just above the cable entry position. 2. Release the cable clamps. 3. Prise the PTC and overload assembly from the compressor. R. SOLENOID VALVES 1. Remove the component as in P above. 2. Located at the rear right hand side (DX). 3. Release 2 screws securing the valve assemblies to a base bracket. 4. Remove the water pipes as necessary. S. PLASTIC EVAPORATION TRAY 1. Remove the components as in P and R above. 2. The tray can now be removed from the rear of the appliance. T. CONDENSER FAN MOTOR 1. Release the 2 screws securing the lower plinth grille beneath the doors. 2. Disconnect the water pipe feeding the in-line connector below the freezer door. 3. Remove the compressor cover as in P above. 4. Release the screw securing the plastic frame of the condenser fan to the back of the appliance. 5. Disconnect the water pipe at the green solenoid. 6. Draw both water pipes through the plastic frame. 7. Disconnect the connections to the motor - This is best done at the module, see page Lay the plastic frame and motor over at the top toward the solenoid valves. Manoeuvre the assembly to remove from the lower brackets and release. 25 of 37

26 U. POWER MODULE 1. Remove the cover as in P. 2. Remove the 2 screws securing the module and cover to the rear right hand edge of the cabinet. 3. Prise the cover from the module box to gain access. V. FRIDGE DAMPER (BAFFLE) WORKING FROM THE FREEZER COMPARTMENT 1. Remove the ice bucket. 2. Remove the 2 screws and remove the top vent. NOTE: the bottom edge of the vent slots behind the rear panel. 3. Pull the shaped duct tube from where it locates in the right hand (DX) duct channel. WORKING FROM THE FRIDGE COMPARTMENT 4. Pull the front cover off the damper housing. This can be tight. 5. Remove the 2 screws and remove the damper housing. 6. Release the damper assembly from the liner by depressing all 4 legs located on the freezer compartment side. 7. Disconnect the wiring from the damper motor. 8. Remove the polystyrene sections from the damper. Check the seals on reassembly. W. CONTROL PANEL INTERFACE 1. Lift the water drain grille from below the dispensing levers and remove the 2 screws. 2. Ease the control panel away from the door at the bottom and lift to remove. 3. Disconnect the edge connectors. X. DISPLAY PCB MODULE 1. Remove the control panel interface as in W above. 2. Remove the 5 x T10 screws securing the cover over the PCB. 3. Remove 1 x T10 screw securing the module. 4. Prise the 2 tabs away to remove the PCB. Y. DISPENSER SWITCHES & LAMP 1. Remove the control panel interface as in W above. 2. Depress or open tabs to remove switches or lamp holder. Lamp 10W SES. Z. DISPENSER LEVERS 1. Remove the control panel interface as in W above. 2. Disconnect the various connectors. 3. Release the 2 screws and remove the white moulding holding the switches and lamp holder. 4. Remove the clear Perspex cover on the ice dispenser lever. This can be helped by gently twisting on the lever to release the hooks from the rear of the lever. 5. Disassemble the damper assembly in the dispenser - i.e. round white object at the top of the dispenser frame toward the right hand side (DX). 6. Remove the hex head screw and spring clip (note small spacer under clip) between the two levers. 7. The long hinge pin can be released from the right hand end only (note the position of a metal spacing washer between the white and brown mouldings on the hinge pin). 8. Using Sniped Nose pliers, grip the right hand (DX) end of the pin and push upward to release. Draw the pin out to the right hand side to release the whole assembly. 26 of 37

27 COMPRESSOR CONNECTION CHART EMBRACO COMPRESSOR TERMINAL BLOCK 1 ~ COMMON (Overload) L ~ LIVE (line) & Capacitor ~ EARTH S ~ CAPACITOR N ~ NEUTRAL SCHEMATIC VIEW OF TERMINAL BLOCK TERMINAL COLOUR DESCRIPTION 1 BLACK COMMON (OVERLOAD) L BROWN LIVE & RUN CAPACITOR GREEN/YELLOW EARTH N BLUE NEUTRAL S BLUE RUN CAPACITOR 1 L N S 27 of 37

28 28 of 37 POWER MODULE EDGE CONNECTIONS SOME TERMINALS MAY NOT BE USED, DEPENDING ON THE MODEL Pin 9 ( water valve feedback ) Pin 10 ( NC ) Pin 11 ( Emitter IDI load ) Pin 12 ( Freezer lamp load ) Pin 13 ( Fridge lamp load ) Pin 14 ( Defrost heater load ) Pin 15 ( IMC load ) Pin 16 ( Receiver IDI load ) Pin 3 ( Condenser fan line ) Pin 2 ( Water valve line ) Pin 1 ( Ice valve line ) Pin 8 ( IMC water valve return ) Pin 7 ( Fridge lamp feedback ) Pin 6 ( Freezer lamp feedback ) Pin 5 ( Lamps line ) Pin 4 ( Damper line ) Pin 3 ( Reciever IDI line ) Pin 2 ( Freezer door line ) Pin 1 ( Freezer line ) Pin 10 ( DC Fan optional ) Pin 9 ( Ice maker + ) Pin 12 ( Freezer door communication RX ) Pin 8 ( Ice maker - ) Pin 11 ( Freezer door communication TX ) Pin 7 ( Ice maker probe ) Pin 10 ( Freezer door UI neutral ) Pin 6 ( Ice maker probe ) Pin 9 ( NC ) Pin 8 ( Evaporator fan load ) Pin 7 ( Damper load ) Pin 4 ( Freezer probe ) Pin 3 ( Fridge probe ) Pin 1 ( Fridge probe ) Pin 2 ( Freezer probe ) Pin 1 ( Bimetallic feedback ) Pin 2 ( NC ) Pin 3 ( Reciever IDI feedback ) Pin 1 ( Ice maker Neutral ) Pin 4 ( Motor Load-Neutral ) Pin 2 ( Ice maker Hall ) Pin 5 ( Damper feedback ) Pin 3 ( Ice maker + 12 VC ) Pin 6 ( Emitter IDI line ) Pin 4 ( Ice maker Test ) Pin 5 ( DC Fan Optional ) Indesit Company

29 CONNECTOR BLOCK CHART DISPENSER ASSEMBLY CONTROL PANEL MODULE ICE DISPENSER MICRO SWITCHES WATER DISPENSER HEATER SWITCH 6-PIN CONNECTOR LAMP HOLDER FREEZER DOOR EVAPORATOR FAN FRIDGE COMPARTMENT & CUT-OUT TOP HINGE 6-PIN CONNECTOR DAMPER 29 of 37

30 THEORETICAL WIRING DIAGRAM 30 of 37

31 THERMISTOR (NTC) SENSOR LOCATION Two sensors are used in these models, the approximate position is as follows: - 1. Freezer Air Sensor - Located in the left liner wall just below the icemaker. 2. Fridge Air Sensor - Located in the centre of the rear liner wall of the fridge. Temperature ( C) NTC resistance (Ohm) Accuracy (± C) Temperature ( C) NTC resistance (Ohm) Accuracy (± C) , ,7 9, , , ,7 8, , , ,7 7, , , ,8 6, , , ,8 5, , , ,8 4, , , ,8 3, , , ,8 2, , , ,9 1, , , ,9 0, , , ,9-0, , , ,9-1, , , ,9-2, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , of 37

32 INSTALLATION INSTRUCTIONS INTRODUCTION The model you are installing may differ slightly with respect to some descriptions in this installation, since this covers several models. Install the appliance in a dry and well-ventilated place. Avoid locations in direct sunlight or near a source of heat (oven, heating, etc.). If this cannot be avoided, install the appliance respecting the following minimum distances: Coal or paraffin stoves: 300 mm Electric and/or gas stoves: 30 mm To allow product handling and sufficient air circulation, leave at least 10 mm clearance at the sides, above the appliance, and between the rear panel and the wall. WATER CONNECTION Disconnect the appliance from the mains power supply before starting operations. The icemaker and water circuit must be connected to a water supply of potable and/or chemically purified water. The water connection must be carried out in compliance with local regulations. The appliance is supplied with a water tube, already attached to the back of the product. Remove the shipping tape from the coiled water tubing on the rear of the appliance. Connect the transition connector (1) to the household water supply (2). Make sure that the water tube is not twisted. The appliance is pre-set for operation at pressures between 1.7 and 8.1 bar (25 and 117 PSI). Open the water tap. Check for and eliminate any leaks. The appliance does not require any adjustment or water drain. ELECTRICAL CONNECTIONS Regulations require that the appliance is earthed. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the prescriptions. Make sure that the installation and the electrical connection are carried out by a qualified technician according to the manufacturer s instructions and local safety regulations. Ensure that the voltage indicated on the appliance data plate corresponds to the mains voltage. The plug of the appliance must be easily accessible even after installation so that the appliance can be unplugged if necessary. If this is not possible, we recommend the appliance is connected to the mains supply by means of a two-pole switch with minimum break distance between contacts of 3 mm, fitted at an easily accessible point. Do not use extension leads or adapters. After installation, make sure that the appliance is not standing on the power supply cable. 32 of 37

33 INSTALLATION INSTRUCTIONS LEVELLING THE APPLIANCE The refrigerator has two front and two rear wheels at the base of the product on each side that can be adjusted (see Figure A), or four wheels of which only the two front wheels can be adjusted (see Figure B). If the appliance seems unsteady or you want the doors to close easier, adjust the appliance's tilt, following the instructions below (depending on the model, as shown in the figures on the right). Figure A 1. Check the installation location to be sure you have at least 10 mm clearance on all sides including the top. 2. Connect the appliance to the mains power supply. 3. Move the refrigerator into its final position. 4. Open both doors and remove the plinth to locate the levelling bolts at the left and right of the refrigerator base. The top bolt (1) will adjust the rear wheel (if provided), and the bottom bolt (2) will adjust the front wheel. 5. Use the wrench provided to adjust the levelling bolts. Turn the levelling bolt clockwise to raise the appliance, or Figure B anti-clockwise to lower it. It may take several turns of the levelling bolts to adjust the tilt of the refrigerator. Note: do not unscrew the levelling bolts too much when lowering the appliance as they could fall out. Aligning the Doors If, after switching on the appliance and adjusting the refrigerator and freezer doors, the doors are misaligned, disconnect the appliance from the power supply and adjust both doors as indicated in the following diagrams. 33 of 37

34 INSTALLATION INSTRUCTIONS REMOVING THE FREEZER DOOR (A) REMOVING THE REFRIGERATOR DOOR (B) 34 of 37

35 INSTALLATION INSTRUCTIONS MOUNTING THE FREEZER DOOR (C) MOUNTING THE REFRIGERATOR DOOR (D) 35 of 37

36 INSTALLATION INSTRUCTIONS HORIZONTAL ALIGNMENT OF FREEZER AND REFRIGERATOR DOORS (E) VERTICAL ALIGNMENT OF FREEZER AND REFRIGERATOR DOORS (F) 36 of 37

37 37 of 37

Essentia Project Artica Platform No Frost 60 cm Appliances 2011

Essentia Project Artica Platform No Frost 60 cm Appliances 2011 Essentia Project Artica Platform No Frost 60 cm Appliances 2011 Event Ca Maiano, May 2011 Presenter Piotr Kelm Francesco Nieli 0 Legend and User Interface Legend THR3 Interface (SQG_CL_32) MID Indesit

More information

Service Information INDESIT FREESTANDING FRIDGE FREEZERS. Indesit Company UK Ltd CA55UK CA55KUK CA55SUK 75733

Service Information INDESIT FREESTANDING FRIDGE FREEZERS. Indesit Company UK Ltd CA55UK CA55KUK CA55SUK 75733 5407586 Issue 3 May 2012 INDESIT FREESTANDING FRIDGE FREEZERS Models Covered Comm. Code CA55UK 69937 CA55KUK 74471 CA55SUK 75733 Service Information Energy Band A+ Models CAA55UK 77736 CAA55KUK 77739 CAA55SUK

More information

SERVICE MANUAL REFRIGERATION

SERVICE MANUAL REFRIGERATION SERVICE MANUAL REFRIGERATION Electrolux Home Products S.p.A. Spares Operations Italy Corso lino Zanussi, 30 I - 33080 Porcia (PN) Fax +39 0434 394096 S.O.I. Edition: 10.2006 Publication no. 599 38 38-50

More information

KitchenAid Food Stream Solutions Classic and Integrated Series

KitchenAid Food Stream Solutions Classic and Integrated Series KitchenAid Food Stream Solutions Classic and Integrated Series KitchenAid Chapter list Installation Range overview Installation General Information Function Compressor Power Control Board Defrosting Heating

More information

SERVICE MANUAL REFRIGERATION

SERVICE MANUAL REFRIGERATION SERVICE MANUAL REFRIGERATION ELECTROLUX HOME PRODUCTS S.p.A. Publication no. Spares Operations Italy 599 37 75-07 Corso Lino Zanussi, 30 060824 I - 33080 PORCIA / PN (ITALY) ITZ/SERVICE/AA Fax +39 0434

More information

SERVICE MANUAL New Electronic Cold Platform 2005.

SERVICE MANUAL New Electronic Cold Platform 2005. SERVICE MANUAL New Electronic Cold Platform 2005. All the parts included in this document are the property of Indesit Company S.p.A. All rights reserved. This document and the information it contains are

More information

ER MANUAL FOR YOUR BAUMATIC

ER MANUAL FOR YOUR BAUMATIC BW18BL 50 litre thermoelectric beverage centre BW28BL 70 litre thermoelectric beverage centre ER MANUAL FOR YOUR BAUMATIC BW18BL 50 litre thermoelectric beverage centre BW28BL 70 litre thermoelectric beverage

More information

SERVICE MANUAL REFRIGERATION

SERVICE MANUAL REFRIGERATION SERVICE MANUAL REFRIGERATION ELECTROLUX ZANUSSI S.p.A. Publication No. Spares Operations Italy 599 35 40-29 Corso Lino Zanussi, 30 020806 I - 33080 PORCIA / PN (ITALY) ITZ/SERVICE/AA EUROFLEC With exposed

More information

Service Information. WNes 2956 appliance documentation. Service Information no. 27/2004 LHG/TKD-Fe/June SI

Service Information. WNes 2956 appliance documentation. Service Information no. 27/2004 LHG/TKD-Fe/June SI After Sales Service International Service Information Service Information no. 27/2004 LHG/TKD-Fe/June 2004 WNes 2956 appliance documentation Page 1/26 Contents 2.0. Extract from Operating Instructions

More information

PRODUCT DESCRIPTION CONTROLS

PRODUCT DESCRIPTION CONTROLS PRODUCT DESCRIPTION A. Refrigerator Compartment 1. Crisper drawer 2. Shelves / Shelf area 3. Thermostat control knob/light 4. Door trays 5. Bottle rack 6. Removable bottle restraint 7. Rating plate (at

More information

HUL litre Built-under larder fridge

HUL litre Built-under larder fridge USER MANUAL FOR YOUR HUL136.1 136 litre Built-under larder fridge NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get

More information

Refrigerator. Installation Guide. Free Standing Appliance

Refrigerator. Installation Guide. Free Standing Appliance Refrigerator Guide Free Standing Appliance Untitled-3 1 2018-04-10 12:31:22 Follow these instructions carefully to prevent accidents and to ensure the proper installation of this refrigerator. WARNING

More information

Refrigerator KE T

Refrigerator KE T Refrigerator KE 680-1-3T Service Manual: H8-74-07 Responsible: U. Laarmann KÜPPERSBUSCH HAUSGERÄTE AG E-mail: uwe.laarmann@kueppersbusch.de Tel.: (0209) 401-732 Customer Service Fax: (0209) 401-743 Postfach

More information

DISHWASHER - PART RECOGNITION GUIDE

DISHWASHER - PART RECOGNITION GUIDE DISHWASHER - PART RECOGNITION GUIDE SPRAY ARM HOLDER UPPER SPRAY ARM FILTER ASSEMBLY LOWER SPRAY ARM ASSEMBLY SUMP DISHWASHER - PART RECOGNITION GUIDE DISPENSER DOOR SPRING DOOR HINGE INNER DOOR DOOR THERMOSTAT

More information

Contents. For your safety About your product Installing your appliance Using your appliance Care & cleaning...

Contents. For your safety About your product Installing your appliance Using your appliance Care & cleaning... USER GUIDE TF5517S Contents For your safety..................................................... 1 About your product.................................................. 3 Installing your appliance...............................................

More information

TABLE OF CONTENTS REFRIGERATOR-FREEZER. Model No. NR-BN34FX1 Model No. NR-BN34FW1

TABLE OF CONTENTS REFRIGERATOR-FREEZER. Model No. NR-BN34FX1 Model No. NR-BN34FW1 Order Number GORR1405001CE REFRIGERATOR-FREEZER Model No. NR-BN34FX1 Model No. NR-BN34FW1 Product-Color X:Stainless W:White Destination E(Europe Continental) B(U.K.) TABLE OF CONTENTS PAGE 1 Safety Precautions-----------------------------------------------

More information

3. OPERATING INSTRUCTIONS & INSTALLATION

3. OPERATING INSTRUCTIONS & INSTALLATION 3-1) Digital Panel 20 3-2) Temperature Control Function 20 3-3) Power Freeze and Power Cool Functions 21 3-4) Child Lock Function 21 3-5) Ice & Water Dispenser Function 22 3-6) C-Fan Motor Delay Function

More information

Service Information. HOTPOINT Freestanding Frost Free Fridge Freezers

Service Information. HOTPOINT Freestanding Frost Free Fridge Freezers 5407423 Issue 1 Feb. 2009 HOTPOINT Freestanding Frost Free Fridge Freezers (Version 2) Refer to Insert below Models Comm. Covered Code FF187EA 40729 FF187EG 39780 FF187EK 53950 FF187EP 39775 FF187EPL 53947

More information

USING THE REFRIGERATOR COMPARTMENT

USING THE REFRIGERATOR COMPARTMENT USING THE REFRIGERATOR COMPARTMENT Switching the appliance on Starting the appliance Insert the plug. The light, located under the control panel or inside the product (depending on model) comes on when

More information

HOW TO OPERATE THE FREEZER COMPARTMENT PAGE 17 HOW TO DEFROST THE FREEZER COMPARTMENT PAGE 19

HOW TO OPERATE THE FREEZER COMPARTMENT PAGE 17 HOW TO DEFROST THE FREEZER COMPARTMENT PAGE 19 33056-GB.fm5 Page 13 Saturday, January 16, 1999 8:47 AM TABLE OF CONTENTS GB BEFORE USING THE APPLIANCE PAGE 14 SAFEGUARDING THE ENVIRONMENT PAGE 14 PRECAUTIONS AND GENERAL HINTS PAGE 15 HOW TO OPERATE

More information

TECHNICAL INFORMATION Touchtronic Clothes Dryers

TECHNICAL INFORMATION Touchtronic Clothes Dryers TECHNICAL INFORMATION Touchtronic Clothes Dryers Includes: T1302, T1303, T1322, T1329ci T1403 & T1405 2004 Miele This page intentionally left blank. Table of Contents GENERAL INFORMATION A. Warning and

More information

MFC501 & MFC701. Manual for installation, use and maintenance. Integrated fridge-freezers. year.

MFC501 & MFC701. Manual for installation, use and maintenance. Integrated fridge-freezers. year. Manual for installation, use and maintenance MFC501 & MFC701 Integrated fridge-freezers year parts + 1 year labour guarantee www.matrixappliances.co.uk Important The CDA Group Ltd cannot be held responsible

More information

Installation. Leveling

Installation. Leveling Your refrigerator was packed carefully for shipment. Remove and discard shelf packaging and tape. Do not remove the serial plate. Location Do not install refrigerator near oven, radiator or other heat

More information

HOW TO USE THE FREEZER COMPARTMENT PAGE 16

HOW TO USE THE FREEZER COMPARTMENT PAGE 16 33051-gb.fm5 Page 12 Tuesday, December 22, 1998 3:52 PM GB CONTENTS BEFORE USING THE APPLIANCE PAGE 13 SAFEGUARDING THE ENVIRONMENT PAGE 13 PRECAUTIONS AND GENERAL RECOMMENDATIONS PAGE 14 HOW TO USE THE

More information

Service Information HOTPOINT BUILT-IN FRIDGE FREEZERS. Indesit Company UK Ltd HM31AAE KM31AAE 79819

Service Information HOTPOINT BUILT-IN FRIDGE FREEZERS. Indesit Company UK Ltd HM31AAE KM31AAE 79819 5407708 Issue 1 Jan. 2013 SM003557 ~ C00293951 HOTPOINT BUILT-IN FRIDGE FREEZERS ACTIVE OXYGEN ENERGY BAND A+ MODELS Models Covered Comm. Code HM31AAE 77896 KM31AAE 79819 Service Information Indesit Company

More information

WESTINGHOUSE ELECTRONICALLY CONTROLLED A SERIES COMPACT SIDE BY SIDE REFRIGERATORS

WESTINGHOUSE ELECTRONICALLY CONTROLLED A SERIES COMPACT SIDE BY SIDE REFRIGERATORS ELECTROLUX HOME PRODUCTS PTY LTD ABN 51 004 762 341 Issue: 1 Technical Publication Nº RE129 Book C27 Date: 08/05 WEB SITE ADDRESS: www.partnship.com.au WESTINGHOUSE ELECTRONICALLY CONTROLLED A SERIES COMPACT

More information

For Models FF2310APS, FF2310APW, FF2310APB 55cm FREESTANDING FRIDGE FREEZER. Instruction Manual

For Models FF2310APS, FF2310APW, FF2310APB 55cm FREESTANDING FRIDGE FREEZER. Instruction Manual For Models FF2310APS, FF2310APW, FF2310APB 55cm FREESTANDING FRIDGE FREEZER Instruction Manual Please read these instructions carefully before use and retain for future reference. Before switching on your

More information

Side-by-side combined refrigerator-freezer

Side-by-side combined refrigerator-freezer REPAIR INSTTRUCTTI I IONS Side-by-side combined refrigerator-freezer 1 SAFETY... 2 4.1 Electronic controller... 8 1.1 Safety instructions... 2 1.2 Repair instructions... 2 2 INSTALLATION... 3 3 OPERATION...

More information

CREDA STORAGE RADIATORS

CREDA STORAGE RADIATORS 5411160 Issue 1 July 99 CREDA STORAGE RADIATORS Models Covered:- AUTOMATIC 79331S 79341S 79351S 79361S (0.85kW) (1.7kW) (2.55kW) (3.4 kw) MANUAL 79334S 79344S 79354S 79364S (0.85kW) (1.7kW) (2.55kW) (3.4kW)

More information

ELECTROLUX ELECTRONICALLY CONTROLLED COMPACT SIDE BY SIDE REFRIGERATORS

ELECTROLUX ELECTRONICALLY CONTROLLED COMPACT SIDE BY SIDE REFRIGERATORS ELECTROLUX HOME PRODUCTS PTY LTD ABN 51 004 762 341 Issue: 1 Technical Publication Nº XRE180 Date: 12/10 WEB SITE ADDRESS: www.partnship.com.au ELECTROLUX ELECTRONICALLY CONTROLLED COMPACT SIDE BY SIDE

More information

KSSS42QDW05, KSSS42QDX05

KSSS42QDW05, KSSS42QDX05 CABINET PARTS 42" BUILT IN REFRIGERATOR 4 97 Litho In U.S.A. (mek) 1 Part No. CABINET PARTS 1 Cabinet (Not A Serviceable Part) 3 2005004 Grommet, Tube Crossover 4 1112023 Roller, Front & Rear (4) 5 Support,

More information

PC71 American Style Fridge Freezer

PC71 American Style Fridge Freezer PC71 American Style Fridge Freezer Installation, Use and Maintenance Customer Care Department The Group Ltd. Harby Road Langar Nottinghamshire NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu

More information

KELVINATOR REFRIGERATORS NO FROST H & SH SERIES

KELVINATOR REFRIGERATORS NO FROST H & SH SERIES ELECTROLUX HOME PRODUCTS PTY LTD ABN 51 004 762 341 PRINT POST APPROVED PP565001/00099 Issue: 1 Technical Publication Nº RE 78 Book C26 Date: 1/04 WEB SITE ADDRESS: www.partnship.com.au KELVINATOR REFRIGERATORS

More information

CABINET PARTS For Model: KSSS48QJX00 (Stainless Steel)

CABINET PARTS For Model: KSSS48QJX00 (Stainless Steel) CABINET PARTS 48" BUILT IN REFRIGERATOR 10 02 Litho In U.S.A. (mek) 1 Part No. 1 LITERATURE PARTS LIT2209249 Use & Care Guide LIT2006651 Energy Label LIT2006748 Service & Wiring Sheet LIT628370 Modular

More information

Service Information ARISTON FREESTANDING LARDER FRIDGES. Indesit Company

Service Information ARISTON FREESTANDING LARDER FRIDGES. Indesit Company 5407366 Issue 1 May 2007 (only for UK Market) ARISTON FREESTANDING LARDER FRIDGES Model Covered Comm. Code Energy Band 'A' Models SD1511 44302 SD1513 44303 SD1711 44308 SD1711V 47201 SD1712V 47203 Service

More information

CABINET PARTS For Models: KSBS20QEWH2, KSBS20QEBL2 (White) (Black)

CABINET PARTS For Models: KSBS20QEWH2, KSBS20QEBL2 (White) (Black) CABINET PARTS REFRIGERATOR 3-99 Litho In U.S.A. (mdg) 1 Part No. CABINET PARTS 1 Literature Parts LIT8170363 Use & Care Guide LIT8170364 Tech Sheet LIT4344134 Energy Label LIT628370 Modular Icemaker Service

More information

Repair Parts List REFRIGERATOR MODEL NUMBER GC20B8C3EB. When requesting service or ordering parts, always provide the following information:

Repair Parts List REFRIGERATOR MODEL NUMBER GC20B8C3EB. When requesting service or ordering parts, always provide the following information: Repair Parts List REFRIGERATOR MODEL NUMBER GC20B8C3EB When requesting service or ordering parts, always provide the following information: - Product Type - Part Number - Model Number - Part Description

More information

FW422 Integrated In Column Larder Fridge Manual for Installation, Use and Maintenance

FW422 Integrated In Column Larder Fridge Manual for Installation, Use and Maintenance FW422 Integrated In Column Larder Fridge Manual for Installation, Use and Maintenance 1 Customer Care Department The Group Ltd. Harby Road Langar Nottinghamshire NG13 9HY T : 01949 862 012 F : 01949 862

More information

Table of Contents. Specifications... page 2. Installation... page 3. Customizing... page 4. Reversing door swing... page 5

Table of Contents. Specifications... page 2. Installation... page 3. Customizing... page 4. Reversing door swing... page 5 Introduction The Scotsman Compact Refrigerator is a unique product, capable of being built into a cabinet because of its front vented, forced-air cooling system. It s also designed to be a companion to

More information

HOW TO OPERATE THE REFRIGERATOR COMPARTMENT

HOW TO OPERATE THE REFRIGERATOR COMPARTMENT HOW TO OPERATE THE REFRIGERATOR COMPARTMENT Switching on the appliance 1. Plug in the appliance 2. When the appliance is plugged in, it is normally factory set to a temperature of 5 C. Adjusting the temperature

More information

CABINET PARTS REFRIGERATOR

CABINET PARTS REFRIGERATOR CABINET PARTS REFRIGERATOR 1 94 Litho In U.S.A. 1 Part No. CABINET PARTS 2 2152011 Front Roller (2) 3 489393 Screw, 4 981122 Roller (Rear) (2) 5 488454 Screw 6 2155013 Clip, Grille 7 489242 Screw 9 836196

More information

FROST FREE FRIDGE FREEZER INSTRUCTION MANUAL. Model No.: PRT260FFSL/ PRT260FFW

FROST FREE FRIDGE FREEZER INSTRUCTION MANUAL. Model No.: PRT260FFSL/ PRT260FFW FROST FREE FRIDGE FREEZER INSTRUCTION MANUAL Model No.: PRT260FFSL/ PRT260FFW This booklet contains the information you will require to install and operate your new appliance. It is important and worthwhile

More information

CABINET PARTS For Models: W8RXNGMWB02, W8RXNGMWS02, W8RXNGMWL02 (Black) (Stainless Steel) (Satina)

CABINET PARTS For Models: W8RXNGMWB02, W8RXNGMWS02, W8RXNGMWL02 (Black) (Stainless Steel) (Satina) CABINET PARTS REFRIGERATOR 1 12 Litho In U.S.A. (mlg)(bay) 1 Part No. Rev.A CABINET PARTS 1 Literature Parts W10402929 Service & Wiring Sheet 2316016 Use & Care Guide 628370 Modular Icemaker Service Sheet

More information

CABINET PARTS For Models: JC2225GEKB13 (Black)

CABINET PARTS For Models: JC2225GEKB13 (Black) CABINET PARTS REFRIGERATOR 5 09 Printed In U.S.A. (mat) (psw) 1 Part No. Rev. A CABINET PARTS 1 Literature Parts 12842135SP Use and Care Guide 12893051 Tech Sheet 2 Cover, Hinge (FC) W10175447 Black 3

More information

CONGRATULATIONS FF.584L.SBS.SS

CONGRATULATIONS FF.584L.SBS.SS CONGRATULATIONS FF.584L.SBS.SS Dear Customer, Thank you for purchasing our Vogue Refrigerator. We are sure you will find your new appliance a pleasure to use. Before you use the appliance, we recommend

More information

CABINET PARTS. For Models: GS5SHAXNQ02, GS5SHAXNT02, GS5SHAXNB02, GS5SHAXNS02, GS5SHAXNL02 (White) (Biscuit) (Black) (Stainless Steel) (Stainless VCM)

CABINET PARTS. For Models: GS5SHAXNQ02, GS5SHAXNT02, GS5SHAXNB02, GS5SHAXNS02, GS5SHAXNL02 (White) (Biscuit) (Black) (Stainless Steel) (Stainless VCM) CABINET PARTS REFRIGERATOR 10 05 Printed In U.S.A. (kdr) 1 Part No. CABINET PARTS 1 Literature Parts 2305895 Energy Guide 2315213 Owner s Manual 2255955 Service & Wiring Sheet 2220407 Modular Icemaker

More information

EGE Manisa 70 cm BIR Carinaro 55 cm. Fabriano June Presenter Francesco Nieli

EGE Manisa 70 cm BIR Carinaro 55 cm. Fabriano June Presenter Francesco Nieli EGE Manisa 70 cm BIR Carinaro 55 cm Fabriano June 2012 Presenter Francesco Nieli Keys and Interfaces Manisa EGE key Carnaro BIR key Tiny Full interface (SQG_CL_??) Tiny SD interface (SQG_CL_??) New LED

More information

CABINET PARTS For Models: 7GS2SHEXPQ03, 7GS2SHEXPL03 (White) (Stainless VCM) REFRIGERATOR

CABINET PARTS For Models: 7GS2SHEXPQ03, 7GS2SHEXPL03 (White) (Stainless VCM) REFRIGERATOR CABINET PARTS REFRIGERATOR 03 07 Litho In U.S.A. (mat) 1 Part No. Rev A CABINET PARTS 1 Literature Parts 2261383 Use & Care Guide 2255955 Service & Wiring Sheet 2261377 Energy Guide 2220407 Modular Icemaker

More information

Bar Fridge USER MANUAL MB46W

Bar Fridge USER MANUAL MB46W Bar Fridge USER MANUAL MB46W CONTENTS Safety information... 2-3 Identifying parts of the fridge... 4 Transporting... 5 Installation... 5 Reversing the door... 6 Operating instructions... 7 Cleaning &

More information

FW852 / FW872 Integrated Fridge Freezer

FW852 / FW872 Integrated Fridge Freezer FW852 / FW872 Integrated Fridge Freezer Installation, Use and Maintenance Customer Care Department The Group Ltd. Harby Road Langar Nottinghamshire NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu

More information

CABINET PARTS For Model: KSSO36FMX01 (Etched Aluminum)

CABINET PARTS For Model: KSSO36FMX01 (Etched Aluminum) CABINET PARTS 36" BUILT IN REFRIGERATOR 9 05 Litho In U.S.A. (kdj) 1 Part No. 1 Literature Parts 2266808 Use & Care Guide 2307362 Energy Label 2306324 Service & Wiring Sheet 2306337 Icemaker and Ingredient

More information

SIDE BY SIDE REFRIGERATOR MODELS: WRS325SDHW00 (White) WRS325SDHB00 (Black) WRS325SDHV00 (Black Stainless) WRS325SDHZ00 (Stainless Steel)

SIDE BY SIDE REFRIGERATOR MODELS: WRS325SDHW00 (White) WRS325SDHB00 (Black) WRS325SDHV00 (Black Stainless) WRS325SDHZ00 (Stainless Steel) SIDE BY SIDE REFRIGERATOR MODELS: WRS325SDHW00 (White) WRS325SDHB00 (Black) WRS325SDHV00 (Black Stainless) WRS325SDHZ00 (Stainless Steel) 03/21/2018 2018 Whirlpool Corporation Part No. W11157383 Rev. B

More information

Operating Instructions

Operating Instructions Operating Instructions FRIDGE English,1 TLA 1 TLA 1 S Contents Installation, 2-4 Positioning and connection Reversible doors Description of the appliance, 5 Overall view Start-up and use, 6 Starting the

More information

CABINET PARTS. For Models: GD2SHAXNQ00, GD2SHAXNT00, GD2SHAXNB00, GD2SHAXNS00, GD2SHAXNL00 (White) (Biscuit) (Black) (Stainless Steel) (Stainless VCM)

CABINET PARTS. For Models: GD2SHAXNQ00, GD2SHAXNT00, GD2SHAXNB00, GD2SHAXNS00, GD2SHAXNL00 (White) (Biscuit) (Black) (Stainless Steel) (Stainless VCM) CABINET PARTS REFRIGERATOR 5 04 Litho In U.S.A. (kdj) 1 Part No. Rev. A CABINET PARTS 1 Literature Parts 2261717 Use & Care Guide 2255955 Service & Wiring Sheet 2305881 Energy Guide 2220407 Modular Icemaker

More information

Repair Parts List REFRIGERATOR MODEL NUMBER MSD2754GRW. When requesting service or ordering parts, always provide the following information:

Repair Parts List REFRIGERATOR MODEL NUMBER MSD2754GRW. When requesting service or ordering parts, always provide the following information: Repair Parts List REFRIGERATOR MODEL NUMBER MSD2754GRW When requesting service or ordering parts, always provide the following information: - Product Type - Part Number - Model Number - Part Description

More information

USER GUIDE. TL6015W TL6018W 60cm Larder

USER GUIDE. TL6015W TL6018W 60cm Larder USER GUIDE TL6015W TL6018W 60cm Larder Thank you for buying this high quality appliance This handbook is designed to help you through each step of owning your new appliance, from installation to use. Please

More information

CZ51202 Larder fridge

CZ51202 Larder fridge CZ51202 Larder fridge USER INSTRUCTIONS Please read these instructions carefully before using this product and keep them safe for future reference. Page contents Before use................................................2

More information

55CM Wide Freestanding Under Counter Freezer Instruction Manual

55CM Wide Freestanding Under Counter Freezer Instruction Manual 55CM Wide Freestanding Under Counter Freezer Instruction Manual Model Number: RHUCFZ1 Please read these instructions carefully and keep them for future reference For Customer Services, Spare Parts & Manufacturer

More information

Image Key Part Number Description Substitution Qty.

Image Key Part Number Description Substitution Qty. Model Number: BOM/Serial #: Graphic Title: XRSR465BW PXRSR465BW0 SUPPLEMENTAL INFORMATION Image Key Part Number Description Substitution Qty. 1 1 67002385 HARNESS-CONTROL 1 1 1 67002384 HARNESS, ICE MAKER

More information

Repair Parts List REFRIGERATOR MODEL NUMBER MSD2656GEB. When requesting service or ordering parts, always provide the following information:

Repair Parts List REFRIGERATOR MODEL NUMBER MSD2656GEB. When requesting service or ordering parts, always provide the following information: Repair Parts List REFRIGERATOR MODEL NUMBER MSD2656GEB When requesting service or ordering parts, always provide the following information: - Product Type - Part Number - Model Number - Part Description

More information

rlrm MOflel S DE-BY-SIDE REFRIGERATOR Always consult the Use & Care Guide for more operating information.

rlrm MOflel S DE-BY-SIDE REFRIGERATOR Always consult the Use & Care Guide for more operating information. rlrm MOflel 401.40483800 S DE-BY-SIDE REFRIGERATOR Always consult the Use & Care Guide for more operating information. 86002-2008 085 JR O ice BiN For storage of ice cubes made by the icemaker. Do not

More information

ELECTROLUX ELECTRONICALLY CONTROLLED COMPACT SIDE BY SIDE REFRIGERATOR

ELECTROLUX ELECTRONICALLY CONTROLLED COMPACT SIDE BY SIDE REFRIGERATOR ELECTROLUX HOME PRODUCTS PTY LTD ABN 51 004 762 341 Issue: 1 Technical Publication Nº XRE33 Date: 7/06 WEB SITE ADDRESS: www.partnship.com.au ELECTROLUX ELECTRONICALLY CONTROLLED COMPACT SIDE BY SIDE REFRIGERATOR

More information

VCBF136RSS3 : CABINET [1/9]

VCBF136RSS3 : CABINET [1/9] VCBF136RSS3 : 001 - CABINET [1/9] Page 1 of 18 VCBF136RSS3 : 001 - CABINET [1/9] Ref # Part Number Qty. Description 1 017000-000 1 COVER, RIGHT HINGE (APOLLO GREY) 2 021734-000 1 SCREW 3 021733-000 3 SCREW

More information

DDBF036 SERIES 10 : REFRIGERATOR DOOR [1/12]

DDBF036 SERIES 10 : REFRIGERATOR DOOR [1/12] DDBF036 SERIES 10 : 001 - REFRIGERATOR DOOR [1/12] Page 1 of 24 DDBF036 SERIES 10 : 001 - REFRIGERATOR DOOR [1/12] Ref # Part Number 1 2 PS400000 PS400001 PS400002 PE030188 PS400003 PS400004 PS400005 PS400006

More information

CABINET PARTS For Model: KSF26C6XYY00 (Monochromatic Stainless)

CABINET PARTS For Model: KSF26C6XYY00 (Monochromatic Stainless) CABINET PARTS REFRIGERATOR 11 11 Litho In U.S.A. (wam) (eeb) 1 Part No. Rev. B CABINET PARTS 1 Literature Parts W10368322 Use & Care Guide W10287673 Service & Wiring Sheet W10403232 Energy Label 2 2150304

More information

CABINET PARTS For Model: KSSC42QTS02 (Stainless Steel)

CABINET PARTS For Model: KSSC42QTS02 (Stainless Steel) CABINET PARTS 42" BUILT IN REFRIGERATOR 10 11 Litho In U.S.A. (jdc)(psw) 1 Part No. Rev. A 1 Literature Parts W10161714 Use & Care Guide W10164072 Energy Guide W10159832 Service & Wiring Sheet 2306424

More information

CABINET PARTS. For Models: ED5SHAXMQ00, ED5SHAMXT00, ED5SHAXMB00 (White) (Biscuit) (Black) REFRIGERATOR. Part No Rev.A

CABINET PARTS. For Models: ED5SHAXMQ00, ED5SHAMXT00, ED5SHAXMB00 (White) (Biscuit) (Black) REFRIGERATOR. Part No Rev.A CABINET PARTS REFRIGERATOR 4 04 Printed In U.S.A. (kdj) 1 Part No. Rev.A LITERATURE PARTS 1 LIT2261135 Energy Guide LIT2255705 Owner s Manual LIT2255380 Service & Wiring Sheet LIT2220407 Modular Icemaker

More information

SERVICE INSTRUCTION. DYNAMIC COOLING with 0 zone REFRIGERATION. Fridge/freezer with. Publication number

SERVICE INSTRUCTION. DYNAMIC COOLING with 0 zone REFRIGERATION. Fridge/freezer with. Publication number SERVICE INSTRUCTION REFRIGERATION DISTRIPARTS AB BOX 501 S-562 80 NORRAHAMMAR Phone 036-31 80 00 Telefax 036-31 81 10 Telefax 036-31 80 88 Publication number 599 51 96-71 Rev. 04-04-20 SV/SERVICE DT/MA/AN

More information

Built-under fridge with ice box instruction manual RBR6. Contact Caple on or for spare parts

Built-under fridge with ice box instruction manual RBR6. Contact Caple on or for spare parts Built-under fridge with ice box instruction manual RBR6 Contact Caple on 0117 938 7420 or for spare parts www.caple.co.uk CONTENTS Warnings 3 Installation warnings 7 Before using your fridge 10 How to

More information

CABINET PARTS. For Models: KBLC36FMS00 (Stainless Steel) 9 05 Litho In U.S.A. (kdj) Part No " BOTTOM MOUNT BUILT IN REFRIGERATOR

CABINET PARTS. For Models: KBLC36FMS00 (Stainless Steel) 9 05 Litho In U.S.A. (kdj) Part No  BOTTOM MOUNT BUILT IN REFRIGERATOR CABINET PARTS 36" BOTTOM MOUNT BUILT IN REFRIGERATOR 9 05 Litho In U.S.A. (kdj) 1 Part No. 1 Literature Parts LIT2266810 Use & Care Guide LIT2266819 Energy Label LIT2266830 Service & Wiring Sheet LIT628370

More information

CABINET PARTS For Model: KBLC36FMS02 (Stainless Steel)

CABINET PARTS For Model: KBLC36FMS02 (Stainless Steel) CABINET PARTS 36" BOTTOM MOUNT BUILT IN REFRIGERATOR 11 05 Litho In U.S.A. (mek) 1 Part No. CABINET PARTS 1 Literature Parts 2317085 Use & Care Guide 2307361 Energy Label 2306322 Service & Wiring Sheet

More information

TCW 2000 Ice liner refrigerator and freezer PIJ

TCW 2000 Ice liner refrigerator and freezer PIJ TCW 2000 Ice liner refrigerator and freezer OVER VIEW The unique rotomoulded Chest Freezer and inclined Refrigerator with two separate compartments and compressors worldwide Hold over time @ 32 C Hold

More information

CABINET PARTS For Models:GC5THEXNQ00, GC5THEXNT00, GC5THEXNB00, GC5THEXNS00 (White) (Biscuit) (Black) (Stainless Steel)

CABINET PARTS For Models:GC5THEXNQ00, GC5THEXNT00, GC5THEXNB00, GC5THEXNS00 (White) (Biscuit) (Black) (Stainless Steel) CABINET PARTS REFRIGERATOR 10 05 Printed In U.S.A. (kdr) 1 Part No. Rev. A CABINET PARTS 1 Literature Parts 2306981 Use & Care Guide 2223419 Service & Wiring Sheet 2223996 Installation Instructions 2223519

More information

Contents Safety Warnings... 3 Unpacking... 5 Installation... 6 Product Overview Operation Cleaning Maintenance...

Contents Safety Warnings... 3 Unpacking... 5 Installation... 6 Product Overview Operation Cleaning Maintenance... L5017W/S/B Contents Safety Warnings... 3 Unpacking... 5 Installation... 6 Location...6 Levelling the Unit...6 Free Space Requirements...6 Reversing the Door Swing...7 Cleaning Before Use... 10 Before Using

More information

MSD2652KES COMPRESSOR

MSD2652KES COMPRESSOR MSD2652KES CABINET 1 67003576 50 ELBOW, FILL TUBE 2 M0114003 50 CLIP, SPEED 3 67003360 50 TUBE, PLASTIC 4 A3223101 50 INSERT, PLASTIC TUBE 5 M0104106 50 CLIP 6 67006506 50 CORD, POWER 7 67006433 50 SCREW

More information

User s Manual UPRIGHT FREEZER WHS-507FWEW1 / WHS-507FWESS1 WHS-625FWEW1 / WHS-625FWESS1 WHS-772FWEW1 / WHS-772FWESS1

User s Manual UPRIGHT FREEZER WHS-507FWEW1 / WHS-507FWESS1 WHS-625FWEW1 / WHS-625FWESS1 WHS-772FWEW1 / WHS-772FWESS1 User s Manual UPRIGHT FREEZER WHS-507FWEW1 / WHS-507FWESS1 WHS-625FWEW1 / WHS-625FWESS1 WHS-772FWEW1 / WHS-772FWESS1 Contents Introductions..................................................... 3 Important

More information

FW851 / FW871 Integrated Fridge Freezer Manual for Installation, Use and Maintenance

FW851 / FW871 Integrated Fridge Freezer Manual for Installation, Use and Maintenance FW851 / FW871 Integrated Fridge Freezer Manual for Installation, Use and Maintenance Customer Care Department The Group Ltd. Harby Road Langar Nottinghamshire NG13 9HY T : 01949 862 012 F : 01949 862 003

More information

REFRIGERATOR Models:

REFRIGERATOR Models: PARTS LIST for REFRIGERATOR Models: MFI2269VEM9 (Stainless) FOR CUSTOMER SATISFACTION ALWAYS USE FACTORY SPECIFICATION PARTS 201209004 2012 Maytag Part No. W10536628 Rev. A CABINET PARTS 201209004 2 Part

More information

HOW TO OPERATE THE FREEZER COMPARTMENT PAGE 15 HOW TO DEFROST THE FREEZER COMPARTMENT PAGE 17

HOW TO OPERATE THE FREEZER COMPARTMENT PAGE 15 HOW TO DEFROST THE FREEZER COMPARTMENT PAGE 17 GB CONTENTS BEFORE USING THE REFRIGERATOR PAGE 13 SAFEGUARDING THE ENVIRONMENT PAGE 13 PRECAUTIONS AND GENERAL RECOMMENDATIONS PAGE 14 HOW TO OPERATE THE REFRIGERATOR COMPARTMENT PAGE 15 HOW TO OPERATE

More information

ELECTROLUX ELECTRONICALLY CONTROLLED A SERIES COMPACT SIDE BY SIDE REFRIGERATOR

ELECTROLUX ELECTRONICALLY CONTROLLED A SERIES COMPACT SIDE BY SIDE REFRIGERATOR ELECTROLUX HOME PRODUCTS PTY LTD ABN 51 004 762 341 Issue: 1 Technical Publication Nº RE203 Date: 11/07 WEB SITE ADDRESS: www.partnship.com.au ELECTROLUX ELECTRONICALLY CONTROLLED A SERIES COMPACT SIDE

More information

Front Roller (2) Screw Roller (Rear) (2) Screw Clip, Grille Screw Insert, Air

Front Roller (2) Screw Roller (Rear) (2) Screw Clip, Grille Screw Insert, Air 2 2174748 Front Roller (2) 3 489456 Screw 4 981122 Roller (Rear) (2) 5 489427 Screw 6 2155013 Clip, Grille 7 489242 Screw 8 2176796 Insert, Air Baffle 9 2156056 Shim 10 2158579 Enclosure, Terminal Block

More information

CABINET PARTS For Model: KSSC42QVS03 (Stainless Steel)

CABINET PARTS For Model: KSSC42QVS03 (Stainless Steel) CABINET PARTS 42" BUILT IN REFRIGERATOR 2 12 Litho In U.S.A. (wlc)(bay) 1 Part No. Rev. A CABINET PARTS 1 Literature Parts W10303989 Use & Care Guide W10205643 Energy Guide W10159832 Service & Wiring Sheet

More information

Bauknecht AG, Industriestrasse 36, 5600 Lenzburg,

Bauknecht AG, Industriestrasse 36, 5600 Lenzburg, Instructions for use UVI 1340/A Bauknecht AG, Industriestrasse 36, 5600 Lenzburg, www.bauknecht.ch Verkauf Telefon 0848 801 002 Fax 0848 801 017 verkauf@bauknecht.ch Kundendienst Telefon 0848 801 001 Fax

More information

CABINET PARTS Printed In U.S.A. (kdr) 1. Part No

CABINET PARTS Printed In U.S.A. (kdr) 1. Part No CABINET PARTS REFRIGERATOR 02 06 Printed In U.S.A. (kdr) 1 Part No. CABINET PARTS 1 Literature Parts 2315184 Use & Care Guide 2301270 Service & Wiring Sheet 2308328 Energy Guide 2220407 Modular Icemaker

More information

REFRIGERAT A OR USE DF1-15 F ridge

REFRIGERAT A OR USE DF1-15 F ridge REFRIGERATOR USE DF1-15 Fridge BEFORE USING THE APPLIANCE. Your new appliance is designed exclusively for domestic use. To ensure best use of your appliance, carefully read the operating instructions which

More information

CABINET PARTS For Model: EF48DBSS (Stainless Steel)

CABINET PARTS For Model: EF48DBSS (Stainless Steel) CABINET PARTS 48" BUILT IN REFRIGERATOR 08 19-13 1 CABINET PARTS 1 Literature Parts W10159566 Use & Care Guide W10165112 Energy Guide W10180103 Service & Wiring Sheet 2306424 Icemaker and Ingredient Care

More information

1. SAFETY WARNINGS INSTALLTION Location Reversing the Door Swing Levelling the Unit... 3

1. SAFETY WARNINGS INSTALLTION Location Reversing the Door Swing Levelling the Unit... 3 Contents 1. SAFETY WARNINGS... 1 2. INSTALLTION... 2 2.1 Location... 2 2.2 Reversing the Door Swing... 2 2.3 Levelling the Unit... 3 2.4 Cleaning Before Use... 3 2.5 Before Using Your Unit... CE BC108

More information

7ED27DQXDN01 GABINETE

7ED27DQXDN01 GABINETE 7ED27DQXDN01 GABINETE 7ED27DQXDN01 GABINETE 2 4386774 FRONT ROLLER (2) 3 489456 SCREW (S/P) 4 981122 ROLLER (REAR) (2) 5 489427 SCREW (S/P) 6 2155013 CLIP, GRILLE (S/P) 7 489478 SCREW (S/P) 9 2181911 SHIM

More information

BEFORE USING THE REFRIGERATOR PAG. 9 PROTECTING THE ENVIRONMENT PAG. 9 PRECAUTIONS AND GENERAL SUGGESTIONS PAG. 9

BEFORE USING THE REFRIGERATOR PAG. 9 PROTECTING THE ENVIRONMENT PAG. 9 PRECAUTIONS AND GENERAL SUGGESTIONS PAG. 9 GB CONTENTS BEFORE USING THE REFRIGERATOR PAG. 9 PROTECTING THE ENVIRONMENT PAG. 9 PRECAUTIONS AND GENERAL SUGGESTIONS PAG. 9 HOW TO USE THE REFRIGERATOR COMPARTMENT PAG. 10 HOW TO USE THE LOW TEMPERATURE

More information

CABINET PARTS. For Models: GC3SHEXNQ00, GC3SHEXNT00, GC3SHEXNB00, GC3SHEXNS00 (White) (Biscuit) (Black) (Stainless Steel)

CABINET PARTS. For Models: GC3SHEXNQ00, GC3SHEXNT00, GC3SHEXNB00, GC3SHEXNS00 (White) (Biscuit) (Black) (Stainless Steel) CABINET PARTS REFRIGERATOR 10 05 Printed In U.S.A. (kdr) 1 Part No. Rev. A CABINET PARTS 1 Literature Parts 2306981 Use & Care Guide 2223419 Service & Wiring Sheet 2223996 Installation Instructions 2308412

More information

4 04 Printed In U.S.A. (kdj) 1. Part No REFRIGERATOR

4 04 Printed In U.S.A. (kdj) 1. Part No REFRIGERATOR CABINET PARTS REFRIGERATOR 4 04 Printed In U.S.A. (kdj) 1 Part No. CABINET PARTS LITERATURE PARTS 1 2305802 Use & Care Guide 2301270 Service & Wiring Sheet 2305630 Energy Label 2220407 Modular Icemaker

More information

Operating Instructions

Operating Instructions Operating Instructions REFRIGERATOR/FREEZER COMBINATION English, 1 CA 55 xx (UK) CAA 55 xx (UK) NCAA 55 xx (UK) Contents Installation, 2-3-4 Positioning and connection Door reversal Description of the

More information

Model Number Nomemclature... 1 Specifications... 3 Refrigeration System... 4 Freezer and Refrigerator Air Circulation... 5 Display Designs...

Model Number Nomemclature... 1 Specifications... 3 Refrigeration System... 4 Freezer and Refrigerator Air Circulation... 5 Display Designs... Samsung AD Refrigerator Familiarization Maytag Technical Training Services 2004 ABS-L2004-012 Model Number Nomemclature... 1 Specifications... 3 Refrigeration System... 4 Freezer and Refrigerator Air

More information

CABINET PARTS For Models: KSSS42QTW03, KSSS42QTB03, KSSS42QTX03 (White) (Black) (Etched Aluminum)

CABINET PARTS For Models: KSSS42QTW03, KSSS42QTB03, KSSS42QTX03 (White) (Black) (Etched Aluminum) CABINET PARTS 42" BUILT IN REFRIGERATOR 10 08 Litho In U.S.A. (mjb)(bay) 1 Part No. Rev. A CABINET PARTS 1 Literature Parts W10161714 Use & Care Guide W10187855 Energy Guide W10159832 Service & Wiring

More information

INSTALLATION. Glass Panel Doors (select models) CAUTION

INSTALLATION. Glass Panel Doors (select models) CAUTION Location Do not install refrigerator near oven, radiator or other heat source. If not possible, shield refrigerator with cabinet material. Do not install where temperature falls below 55 F (13 C) or rises

More information

FWC152, FWC303, FWC603 & FWC623 Wine Coolers Installation, Use and Maintenance

FWC152, FWC303, FWC603 & FWC623 Wine Coolers Installation, Use and Maintenance FWC152, FWC303, FWC603 & FWC623 Wine Coolers Installation, Use and Maintenance Customer Care Department The Group Ltd. Harby Road Langar Nottinghamshire NG13 9HY T : 01949 862 012 F : 01949 862 003 E :

More information

FWC153, FWC304, FWC604 & FWC624

FWC153, FWC304, FWC604 & FWC624 FWC153, FWC304, FWC604 & FWC624 Wine Coolers Installation, use and maintenance www.cda.eu Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation

More information

WHIRLPOOL REFRIGERADOR KSRS25FGSS13

WHIRLPOOL REFRIGERADOR KSRS25FGSS13 CABINET, LITERATURE 1 CABINET, LITERATURE 1 LIT2206106 Literature Parts (Use & Care Guide) 2 2174748 Front Roller (2) 3 3400517 Screw 4 2196236 Roller (Rear) (2) 5 489427 Screw 6 2155013 Clip, Grille 7

More information

CABINET PARTS For Model: KSSC48QVS02 (Stainless Steel)

CABINET PARTS For Model: KSSC48QVS02 (Stainless Steel) CABINET PARTS 48" BUILT IN REFRIGERATOR 2 10 Litho In U.S.A. (mjb) (psw) 1 Part No. Rev. A CABINET PARTS 1 Literature Parts W10161714 Use & Care Guide W10205644 Energy Guide W10159832 Service & Wiring

More information

KSRG25FKWH18, KSRG25FKBL18, KSRG25FKBT18

KSRG25FKWH18, KSRG25FKBL18, KSRG25FKBT18 CABINET PARTS REFRIGERATOR 06 06 Printed In U.S.A. (kdr) 1 Part No. CABINET PARTS 1 Literature Parts 2318581 Use & Care Guide 2255385 Service & Wiring Sheet 2318618 Energy Guide 2220407 Modular Icemaker

More information