Broag Pressurisation equipment

Transcription

1

2 Broag Pressurisation equipment Compact wall mounted and free standing pressurisation units, utilising the latest microprocessor control. For use on sealed heating and cooling systems, offering accurate control and reliability. Digital equipment comes with a 4 digit bright LED display with scrolling messages including pump operation and alarm modes. Single or twin pump configurations. Complete with integral water break tank utilising an AB airgap and a WRAS approved float valve. Twin pump equipment operates as cyclic duty standby with automatic changeover. Internal alarm with mute function. Security password protected. Auto resetting low water detection, for pump protection. Auto resetting high and low pressure alarm. Digital pressure setpoint with adjustable differential. Flood protection through a pump run limit timer. Normally closed, common fault, volt free contact (Boiler interlock). Normally open, individual volt free contacts for pump trip, high pressure, low pressure and sensor health. All volt free contacts are rated for use with electrical supplies up to 30v with a maximum current draw of 5 amps. RS 485 Connectivity Hours run counter (per pump) month service reminder Excessive start alarm (>3 times in 8 hours) Pump pulse option ( second pulse per pump if inactive for 60 days) Fill system option (Not available on 3OD/3OD)

3 Broag Pressurisation equipment

4 3

5 Using Maximum e Remtank Unvented Cylinders supplied with kits o Water at 0 C expands approx. 0.5% o Water at 60 C expands approx..7% Using a safety factor of 5% water expands between o o 0 C and 60 Using the vessel efficiency calculated as above = 4.8% 000 Ltr x.5% = 5 Ltr expansion; 5 / 4.8% = 35 ( vessel) 800 Ltr x.5% = Ltr expansion; / 4.8% = 8 ( vessel) 500 Ltr x.5% = 7.5 Ltr expansion; 7.5 / 4.8% = 7.5 (4 Ltr vessel) (NOTE: The above sizing relates to Cylinder water content ONLY. Any additional system expansion should be calculated independently.) 4

6 5

7 . Flexcon floor standing digital flexfiller.. Flexcon Uni-fil filling set. (Must be disconnected after filling system). 3. Flexcon expansion vessel sited on heating system return. 4. Flexvent Super automatic air vent-mounted vertically where air naturally collects. 5. PS Vessel (Intermediate for heating) or (Buffer for chilled systems). 6. Safety valve and tundish sited on top or above the Boiler or plant. 7. Flamcovent clean de-aerator - in flow from the boiler before the pump. 8. Supastor indirect calorifier. 9. PSD pressure step degasser. 6

8 Remtank SS Direct unvented cylinders Direct unvented cylinders for potable water installations Fluid Flow Sequence Mains Water Isolation Valve (Not Supplied) 3 bar Pressure Reducing Valve Safety Group ( Expansion Relief Valve c/w Non Return Valve) Drain Valve (Not Supplied) Stainless Supastor Hot Water Calorifier Connection (Floor Standing Model) off 3kW 30v/50Hz Immersion Heater Pressure Reducing Valve Pre-Set Selection Guide Property Type Bedsit / beds with bath / shower 3 beds with bath / shower 4 beds with bath / shower /3 beds with baths / showers 4/5 beds with baths / showers Sports club, Restaurant etc. Hotels, Schools etc Safety Group c/w Non Return Valve Relief Direct Size 0 50 or or or or or 000 Tundish Combined Temperature & Pressure Relief Valve Factory Fitted / 95 o C *In areas with a high concentration of Chlorine (00 ppm or above) additional protection of the cylinder is required with an electronic anode. This is an optional extra and is not reflected in the pricing. Vessels Direct vessels can be supplied without kits as a storage vessel Technical Specification Direct (including Kit) Volume (Nominal) 0 litres 50 litres 80 litres 0 litres 50 litres 300 litres 500 litres 800 litres 000 litres Direct Height (mm) Diameter (mm) Weight (Dry kg) Weight (Normal Full kg) T&P Tapping T&P Pressure Setting T&P Temperature Setting Expansion Relief Setting Electrical Heater Quantity Electrical Heater Rating (Each) Re-heat Times (x) Heat Up Times (From Cold) mins 40 mins mins 65 mins mins 80 mins mins 98 mins mins 4 mins Insulation is interlocked polystyrene to allow for inspection of cylinder if required mins 44 mins mins 56 mins 50 Ltr mins 400 mins 80 Ltr mins mins 80 Ltr N.B. The expansion vessel provided is sized to accommodate a total hot water system volume of.5 times the calorifier size. It is the responsibility of the installer to verify that this vessel size is appropriate for the installation and add additional vessels if required. 7

9 Remtank SS Direct unvented cylinders Secondary Flow (0-300) ( ) 0 to 300 litre 500 to 000 litre Technical Specification Connections Volume (Nominal) Height A (mm) Diameter B (mm) Cold Water C (mm) Cold Water Connection Immersion D (mm) T&P Valve J (mm) Immersion K (mm) DHW Flow J DHW Connection 0 litres 50 litres 80 litres 0 litres 50 litres 300 litres 500 litres Direct Direct Direct Direct Direct Direct Direct litres 000 litres Direct Direct / BSP (M) / BSP (M) / BSP (M) / BSP (M) 8

10 Remtank SS unvented cylinders unvented cylinders for potable water installations Fluid Flow Sequence Mains Water Isolation Valve (Not Supplied) 3 bar Pressure Reducing Valve Safety Group ( Expansion Relief Valve c/w Non Return Valve) Drain Valve (Not Supplied) Stainless Supastor Hot Water Calorifier Connection (Floor Standing Model) Port Valve For Use With The IMIT Thermostat Controlling The Primary Flow (Boiler) Water To The Coil 3kW 30v/50Hz Immersion Heater Pressure Reducing Valve Pre-Set Selection Guide Safety Group c/w Non Return Valve Relief Property Type Bedsit / beds with bath / shower 3 beds with bath / shower 4 beds with bath / shower /3 beds with baths / showers 4/5 beds with baths / showers Sports club, Restaurant etc. Hotels, Schools etc Size 0 50 or or or or or 000 Tundish Technical Specification (including Kit) Combined Temperature & Pressure Relief Valve / 95 o C *In areas with a high concentration of Chlorine (00 ppm or above) additional protection of the cylinder is required with an electronic anode. This is an optional extra and is not reflected in the pricing. IMIT Combined Thermostat & Safety Relay Volume (Nominal) 0 litres 50 litres 80 litres 0 litres 50 litres 300 litres 500 litres 800 litres 000 litres Height (mm) Diameter (mm) Weight (Dry kg) Weight (Normal Full kg) T&P Tapping T&P Pressure Setting T&P Temperature Setting Expansion Relief Setting Electrical Heater Quantity Electrical Heater Rating (Each) Re-heat Times (8º Supply) Heat Up Times (From Cold) Max.Primary Pressure (Coil) Primary Flow Rate (Boiler L/min) Primary Resistance (mbar) Continuous Output (mbar) Coil Rating kw mins 9 mins mins 3 mins mins 37 mins mins 7 mins mins 30 mins mins 35 mins mins 38 mins Ltr mins 40 mins Ltr mins 49 mins Ltr Insulation is interlocked polystyrene to allow for inspection of cylinder if required. N.B. The expansion vessel provided is sized to accommodate a total hot water system volume of.5 times the calorifier size. It is the responsibility of the installer to verify that this vessel size is appropriate for the installation and add additional vessels if required. 9

11 Remtank SS unvented cylinders unvented cylinders for potable water installations Secondary Flow (0-300) ( ) 0 to 300 litre 500 litre 800 to 000 litre Technical Specification Connections Volume (Nominal) Height A (mm) Diameter B (mm) Cold Water C (mm) Cold Water Connection Immersion D (mm) Primary Flow F (mm) Primary Return E (mm) Primary Connection DHW Return G (mm) Secondary Return Connection (mm) Thermostat H (mm) T&P Valve J (mm) Immersion K (mm) DHW Flow J DHW Connection 0 litres BSP (F) litres BSP (F) litres BSP (F) litres BSP (F) litres BSP (F) litres BSP (F) litres BSP (F) litres / BSP (M) litres / BSP (M) / BSP (F)./ BSP (F) / BSP (M)./ BSP (M) 0

12 Remtank SS Solar unvented cylinders Solar unvented cylinders for potable water installations Fluid Flow Sequence Mains Water Isolation Valve (Not Supplied) 3 bar Pressure Reducing Valve Safety Group ( Expansion Relief Valve c/w Non Return Valve) Drain Valve (Not Supplied) Stainless Supastor Hot Water Calorifier Connection (Floor Standing Model) Port Valve For Use With The IMIT Thermostat Controlling The Primary Flow (Boiler) Water To The Coil 3kW 30v/50Hz Immersion Heater Pressure Reducing Valve Pre-Set Selection Guide Safety Group c/w Non Return Valve Relief Property Type Bedsit / beds with bath / shower 3 beds with bath / shower 4 beds with bath / shower /3 beds with baths / showers 4/5 beds with baths / showers Sports club, Restaurant etc. Hotels, Schools etc Solar Size 0 50 or or or or or 000 Tundish Technical Specification SS Solar (including Kit) Combined Temperature & Pressure Relief Valve Factory Fitted / 95 o C *In areas with a high concentration of Chlorine (00 ppm or above) additional protection of the cylinder is required with an electronic anode. This is an optional extra and is not reflected in the pricing. Volume (Nominal) 0 litres 50 litres 300 litres 500 litres 800 litres 000 litres IMIT Combined Thermostat & Safety Relay Supastor Solar Height (mm) Diameter (mm) Weight (Dry kg) Weight (Normal Full kg) T&P Tapping T&P Pressure Setting T&P Temperature Setting Expansion Relief Setting Electrical Heater Quantity Electrical Heater Rating (Each) Primary Re-heat Times (8º Supply) Primary Heat Up Times (From Cold) Max.Primary Pressure (Coil) Primary Flow Rate (Boiler L/M) Primary Resistance (mbar) Primary Continuous Output (mbar) Primary Coil Rating KW mins 7 mins mins 30 mins mins 35 mins mins 38 mins Ltr mins 40 mins Ltr mins 49 mins Ltr Insulation is interlocked polystyrene to allow for inspection of cylinder if required. N.B. The expansion vessel provided is sized to accommodate a total hot water system volume of.5 times the calorifier size. It is the responsibility of the installer to verify that this vessel size is appropriate for the installation and add additional vessels if required.

13 Remtank SS Solar unvented cylinders Solar unvented cylinders for potable water installations Secondary Flow (0-300) ( ) 0 to 300 litre 500 litre 800 to 000 litre Technical Specification Connections Volume (Nominal) Height A (mm) Diameter B (mm) Cold Water C (mm) Cold Water Connection Immersion D (mm) Primary Flow F (mm) Primary Return E (mm) Primary Connection DHW Return G (mm) DHW Return Connection (mm) Thermostat H (mm) T&P Valve J (mm) Immersion K (mm) DHW Flow J (mm) DHW Connection Solar Return L (mm) Solar Flow J (mm) Secondary Connection Thermostat Primary Coil Pocket (mm) 0 litres Solar 50 litres Solar 300 litres Solar BSP (F) BSP (F) BSP (F) litres Solar 800 litres Solar / BSP (M) BSP (F) BSP (F) / BSP (M) litres Solar / BSP (M) BSP (F) / BSP (M)

14 Wiring details for all Digital Pressurisation Units Supply Voltage 30- v- Single Phase. Fuse Rating - 5 Amps Max Full Load Current Amps Under normal operation there is a permanent live feed back to the boiler, the water temperature is regulated by the operation of the motorised valve feeding the internal coil. To control the heating times, connect the electrical feed to the thermostat from the program or time clock (L). When the Remtank Calorifier is at the desired temperature, the motorised valve will close and the boiler, itself, will register no demand from the cylinder and shut down if appropriate. Note: Control of hot water via Rematic 945ck and Broag Priority Kits. When using the Rematic 945ck controller and Broag Priority Kits in conjunction with the supplied HWS immersion sensor, fit the supplied brass pocket in the secondary return connection and connect immersion sensor into pocket, the secondary return connection should then be connected into the cold feed supply at the base of the calorifier between the safety group and the calorifier. Sensor wiring connections can be found in the boiler control wiring details. The port valve must be wired as detailed in the diagrams above, with the electrical supply coming from the Priority Kit/Boiler controls. To ensure the correct operation of the Priority Kit set the control thermostat (connected to the port valve) 0 o C higher than the boiler or controller hot water temperature. 3

15 Assembly for Direct, and Solar Hot Water Outlet D 400mm Maximum Length D C Secondary Return (Anode Connection) C Drain Valve (Not Supplied) T&P Tundish B 400mm Minimum Length B A Pressure Reducing Valve Cold Water Inlet 6 Safety Group 00mm Minimum Length 5 To Drain NOTE: The location of the Pressure Reducing Valve,, Safety Group and Drain Valve is flexible, as long as the distances shown and written instructions are followed. This clause allows the Expasnion Vessel to be located above the Hot Water Calorifer / Cylinder. 4 Designed by Checked by Approved by Date Date RJAC MC RJAC 5/05/006 0/0/ mm Minimum Length Stainless Supastor Direct Assembly To Drain Appendix 4 Edition Sheet / A Hot Water Outlet D 400mm Maximum Length D Secondary Return (Anode Connection) C Drain Valve (Not Supplied) T&P Tundish C Primary Flow (Boiler) B 400mm Minimum Length B Safety Group To Drain 50mm Minimum Length A Pressure Reducing Valve Cold Water Inlet 6 00mm Minimum Length 5 Primary Return (Boiler) NOTE: The location of the Pressure Reducing Valve,, Safety Group and Drain Valve is flexible, as long as the distances shown and written instructions are followed. This clause allows the Expasnion Vessel to be located above the Hot Water Calorifer / Cylinder. 4 Designed by Checked by Approved by Date Date RJAC MC RJAC 5/05/006 0/0/006 3 Stainless Supastor and Solar Assembly To Drain Appendix 3 Edition Sheet / A 4

16 Issue date: Ed/66/xx/xxxx