LA 820 / LA 820 RC Liquid Adhesive Gun

Size: px
Start display at page:

Download "LA 820 / LA 820 RC Liquid Adhesive Gun"

Transcription

1 Liquid Adhesive Gun Manual English NORDSON BENELUX MAASTRICHT THE NETHERLANDS

2 Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which is protected by copyright. Original copyright date No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Nordson Corporation. The information contained in this publication is subject to change without notice All rights reserved. Trademarks AccuJet, AeroCharge, AquaGuard, Asymtek, Automove, Autotech, Baitgun, Blue Box, CanWorks, Century, CF, Clean Coat, CleanSleeve, CleanSpray, Control Coat, Coolwave, Cross-Cut, Cyclo-Kinetic, Dispensejet, DispenseMate, DuraBlue, Durafiber, Durasystem, Easy Coat, Easymove Plus, Econo-Coat, EFD, ETI, Excel 2000, FlexiCoat, Flexi-Spray, Flex-O-Coat, Flow Sentry, Fluidmove, FoamMelt, FoamMix, Heli-flow, Helix, Horizon, Hot Shot, icontrol, Isocoil, Isocore, Iso-Flo, JR, KB30, Kinetix, Little Squirt, Magnastatic, March, MEG, Meltex, Microcoat, Micromark, MicroSet, Millenium, Mini Squirt, Moist-Cure, Mountaingate, MultiScan, Nordson, OmniScan, OptiMix, Package of Values, PatternView, PermaFlo, Plasmod, PluraFoam, Porous Coat, PowderGrid, Powderware, Prism, ProBlue, Pro-Flo, ProLink, Pro-Meter, Pro-Stream, RBX, Rhino, Saturn, SC5, S. design stylized, Seal Sentry, Select Charge, Select Coat, Select Cure, Slautterback, Smart-Coat, Solder Plus, Spectrum, Speed-Coat, Spraymelt, Spray Squirt, Super Squirt, Sure Coat, Tela-Therm, Tracking Plus, Trends, Tribomatic, Ultrasaver, UniScan, UpTime, Veritec, VersaBlue, Versa-Coat, Versa-Screen, Versa-Spray, Walcom, Watermark, When you expect more. are registered trademarks of Nordson Corporation. Advanced Plasma Systems, AeroDeck, AeroWash, Apogee, ATS, Auto-Flo, AutoScan, BetterBook, CanNeck, Celero, Chameleon, Check Mate, ColorMax, Controlled Fiberization, Control Weave, CPX, DispensLink, Dry Cure, Dura-Coat, DuraPail, Dura-Screen, Easy Clean, Eclipse, EcoDry, e.dot, E-Nordson, Equi=Bead, ESP, e Stylized, Fillmaster, Fill Sentry, Gluie, HDLV, iflow, Ink-Dot, ion, Iso-Flex, itrax, itrend, KVLP, Lacquer Cure, Lean Cell, Maxima, MicroFin, MicroMax, Minimeter, Multifil, OptiStroke, Origin, PatternPro, PluraMix, Powder Pilot, Powercure, Primarc, Printplus, Process Sentry, Pulse Spray, PurTech, Ready Coat, Royal Blue, Scoreguard, Select Series, Sensomatic, Shaftshield, SheetAire, Spectral, Spectronic, Speedking, Spray Works, Summit, SureBead, Sure Brand, Sure Clean, Sure-Max, Swirl Coat, Tempus, ThruWave, Trade Plus, Trak, True Blue, Ultra, Ultrasmart, Universal, Vantage, Viper, Vista, Web Cure, 2 Rings (Design) are trademarks of Nordson Corporation. Designations and trademarks stated in this document may be brands that, when used by third parties for their own purposes, could lead to violation of the owners rights Nordson Corporation

3 Table of Contents I Table of Contents Nordson International O-1 Europe O-1 Distributors in Eastern & Southern Europe O-1 Outside Europe / Hors d Europe / Fuera de Europa O-2 Africa / Middle East O-2 Asia / Australia / Latin America O-2 Japan O-2 North America O-2 General Hot Melt Material Processing Instructions Storage Preparations for Material Application/Coating Processing Temperature Danger of Burns Mixing Hot Melt Materials Disposal of Hot Melt Material Additional Note for Polyurethane (PUR) Safety Safety Alert Symbols Responsibilities of the Equipment Owner Safety Information Instructions, Requirements, and Standards User Qualifications Applicable Industry Safety Practices Intended Use of the Equipment Instructions and Safety Messages Installation Practices Operating Practices Maintenance and Repair Practices Equipment Safety Information Equipment Shutdown Relieving System Hydraulic Pressure De-energizing the System Disabling the Guns General Safety Warnings and Cautions Other Safety Precautions First Aid Special Safety Instructions Safety Labels on the Gun Safety Instructions in the Manual Nordson Corporation

4 II Table of Contents Description Intended Use Unintended Use Examples Safety Instructions Residual Risks General Information Updated Bill of Material Functioning Method of Operation Components LA LA 820 RC LogiComm LA 820 RC LA4xx Installation Unpacking Transport Storage Disposal Installation Connecting Material Lines Electrical Lines Setting the Adhesive Quantity, LA Setting the Adhesive Quantity, LA 820 RC Mounting Brackets Operation General Adhesive Processing Instructions Compatibility of Different Types of Adhesives Switching Off in an Emergency Initial Startup Daily Startup Daily Shutdown Maintenance Preventive Maintenance Cleaning the Liquid Adhesive Gun Regular Maintenance Disassembling the LA 820 Liquid Adhesive Gun Disassembling the LA 820 RC Liquid Adhesive Gun Assembling the LA 820 Liquid Adhesive Gun Assembling the LA 820 RC Liquid Adhesive Gun Nordson Corporation

5 Table of Contents III Troubleshooting Parts Introduction Updated Bill of Material Parts Liquid Adhesive Gun, LA 820-7/16-20 UNF Liquid Adhesive Gun, LA 820-1/2-20 UNF Liquid Adhesive Gun, LA 820 RC LogiComm Liquid Adhesive Gun, LA 820 RC LA4xx Module, Liquid Adhesive Gun, LA 820 for LA 4xx Module, Liquid Adhesive Gun, LA 820 RC LogiComm Module, Liquid Adhesive Gun, LA 820 RC LA4xx Filter Ass y, Liquid Adhesive Gun, LA 820 RC Nozzles, Liquid Adhesive Gun, LA Nozzles, Liquid Adhesive Gun, LA 820 RC Manifold for 2 Liquid Adhesive Guns, LA 820-7/16-20 UNF, Stackable Manifold for 2 Liquid Adhesive Guns, LA 820-1/2-20 UNF, Stackable Manifold for Additional Liquid Adhesive Gun LA 820, Stackable Kits Nozzle Kit, Liquid Adhesive Gun, LA Upgrade Kit from Liquid Adhesive Guns LA 820 to LA 820 RC 7-25 Needle and Nozzle Kit, Liquid Adhesive Gun, LA Needle and Nozzle Kit, Liquid Adhesive Gun, LA 820 RC Seal Kit, Liquid Adhesive Gun, LA Accessories Power Cables Adhesive Connection Adapter Technical Data General Data Dimensions Liquid Adhesive Gun, LA Liquid Adhesive Gun, LA 820 RC Mounting Bracket, Liquid Adhesive Gun, LA 820 RC Nordson Corporation

6 IV Table of Contents 2007 Nordson Corporation

7 Introduction O-1 Nordson International Europe Country Phone Fax Austria Belgium Czech Republic Denmark Hot Melt Finishing Finland France Germany Erkrath Lüneburg Nordson UV EFD Italy Netherlands Norway Hot Melt Poland Portugal Russia Slovak Republic Spain Sweden Switzerland United Kingdom Hot Melt Finishing Nordson UV Distributors in Eastern & Southern Europe DED, Germany Nordson Corporation All rights reserved NI_EN_M-0307

8 O-2 Introduction Outside Europe / Hors d Europe / Fuera de Europa For your nearest Nordson office outside Europe, contact the Nordson offices below for detailed information. Pour toutes informations sur représentations de Nordson dans votre pays, veuillez contacter l un de bureaux ci-dessous. Para obtener la dirección de la oficina correspondiente, por favor diríjase a unas de las oficinas principales que siguen abajo. Contact Nordson Phone Fax Africa / Middle East DED, Germany Asia / Australia / Latin America Pacific South Division, USA Japan North America Japan Canada USA Hot Melt Finishing Nordson UV NI_EN_M Nordson Corporation All rights reserved

9 Introduction 0-3 General Hot Melt Material Processing Instructions NOTE: Before processing hot melt material, carefully read the material manufacturer s Material Safety Data Sheet (MSDS) or material information sheet. Nordson supplies only general processing instructions and is not liable for hazards associated with or damage caused by the use of hot melt material. Storage Store the material in dry areas at room temperature. Keep it in covered, dust-protected containers. Preparations for Material Application/Coating Keep the substrate at room temperature, dry, and free of dust and grease. Perform tests to determine the suitable hot melt material, optimum operating conditions, and preliminary treatment of the substrate for the application. Some substrates contain plasticizers and other ingredients which dissipate over time. In some cases, surfaces are treated with waxes, anti-stick oils, etc. Without adequate pretreatment, the hot melt bond in these applications may be defective at the time of dispensing. Processing Temperature The application temperature of the hot melt material at the nozzle is crucial for effective bonds. Refer to the material manufacturer s MSDS or material information sheet. Avoid unnecessary thermal stress. If the work is interrupted, reduce the melting temperature. Avoid heating the hot melt material above the prescribed processing temperature. Higher temperatures may cause charring of the hot melt material. This results in downtime. In addition, material may generate dangerous vapors at excessively high temperatures. Remove these vapors by using appropriate exhaust systems Nordson Corporation HMIPUR01_EN_B1294

10 0-4 Introduction Danger of Burns Be careful when using hot melt materials. These materials are solid at room temperature. For proper application, they may be heated to temperatures of up to 230 C (450 F). Refer to the safety instructions in the Safety section. Mixing Hot Melt Materials Avoid mixing different hot melt materials. Refer to Changing the Hot Melt Material in the Maintenance section. Disposal of Hot Melt Material Refer to the supplier s MSDS or material information sheet. Additional Note for Polyurethane (PUR) When processing Polyurethane-type hot melt materials (PUR), you must follow these additional instructions carefully: Use appropriate respiratory equipment when material vapors exceed permissible limit values. If prescribed by the material manufacturer, pressurize the applicator s tank with an inert gas blanket. During production breaks, set the temperature back and close the gun nozzles temporarily with vaseline or dip them into another suitable oil. Do not empty the tank completely. PUR material residues in bores may cure. Before longer standstill periods, purge the system with a fluid recommended by the material manufacturer. HMIPUR01_EN_B Nordson Corporation

11 Safety 1-1 Section 1 Safety Read this section before using the equipment. This section contains recommendations and practices applicable to the safe installation, operation, and maintenance (hereafter referred to as use ) of the product described in this document (hereafter referred to as equipment ). Additional safety information, in the form of task-specific safety alert messages, appears as appropriate throughout this document. WARNING: Failure to follow the safety messages, recommendations, and hazard avoidance procedures provided in this document can result in personal injury, including death, or damage to equipment or property. Safety Alert Symbols The following safety alert symbol and signal words are used throughout this document to alert the reader to personal safety hazards or to identify conditions that may result in damage to equipment or property. Comply with all safety information that follows the signal word. WARNING: Indicates a potentially hazardous situation that, if not avoided, can result in serious personal injury, including death. CAUTION: Indicates a potentially hazardous situation that, if not avoided, can result in minor or moderate personal injury. CAUTION: (Used without the safety alert symbol) Indicates a potentially hazardous situation that, if not avoided, can result in damage to equipment or property Nordson Corporation A1EN01[XXSAFE]10

12 1-2 Safety Responsibilities of the Equipment Owner Equipment owners are responsible for managing safety information, ensuring that all instructions and regulatory requirements for use of the equipment are met, and for qualifying all potential users. Safety Information Research and evaluate safety information from all applicable sources, including the owner-specific safety policy, best industry practices, governing regulations, material manufacturer s product information, and this document. Make safety information available to equipment users in accordance with governing regulations. Contact the authority having jurisdiction for information. Maintain safety information, including the safety labels affixed to the equipment, in readable condition. Instructions, Requirements, and Standards Ensure that the equipment is used in accordance with the information provided in this document, governing codes and regulations, and best industry practices. If applicable, receive approval from your facility s engineering or safety department, or other similar function within your organization, before installing or operating the equipment for the first time. Provide appropriate emergency and first aid equipment. Conduct safety inspections to ensure required practices are being followed. Re-evaluate safety practices and procedures whenever changes are made to the process or equipment. A1EN01[XXSAFE] Nordson Corporation

13 Safety 1-3 User Qualifications Equipment owners are responsible for ensuring that users: Receive safety training appropriate to their job function as directed by governing regulations and best industry practices Are familiar with the equipment owner s safety and accident prevention policies and procedures Receive, equipment- and task-specific training from another qualified individual NOTE: Nordson can provide equipment-specific installation, operation, and maintenance training. Contact your Nordson representative for information Possess industry- and trade-specific skills and a level of experience appropriate to their job function Are physically capable of performing their job function and are not under the influence of any substance that degrades their mental capacity or physical capabilities 2004 Nordson Corporation A1EN01[XXSAFE]10

14 1-4 Safety Applicable Industry Safety Practices The following safety practices apply to the use of the equipment in the manner described in this document. The information provided here is not meant to include all possible safety practices, but represents the best safety practices for equipment of similar hazard potential used in similar industries. Intended Use of the Equipment Instructions and Safety Messages Use the equipment only for the purposes described and within the limits specified in this document. Do not modify the equipment. Do not use incompatible materials or unapproved auxiliary devices. Contact your Nordson representative if you have any questions on material compatibility or the use of non-standard auxiliary devices. Read and follow the instructions provided in this document and other referenced documents. Familiarize yourself with the location and meaning of the safety warning labels and tags affixed to the equipment. Refer to Safety Labels and Tags (if available) at the end of this section. If you are unsure of how to use the equipment, contact your Nordson representative for assistance. A1EN01[XXSAFE] Nordson Corporation

15 Safety 1-5 Installation Practices Install the equipment in accordance with the instructions provided in this document and in the documentation provided with auxiliary devices. Ensure that the equipment is rated for the environment in which it will be used and that the processing characteristics of the material will not create a hazardous environment. Refer to the Material Safety Data Sheet (MSDS) for the material. If the required installation configuration does not match the installation instructions, contact your Nordson representative for assistance. Position the equipment for safe operation. Observe the requirements for clearance between the equipment and other objects. Install lockable power disconnects to isolate the equipment and all independently powered auxiliary devices from their power sources. Properly ground all equipment. Contact your local building code enforcement agency for specific requirements. Ensure that fuses of the correct type and rating are installed in fused equipment. Contact the authority having jurisdiction to determine the requirement for installation permits or inspections. Operating Practices Familiarize yourself with the location and operation of all safety devices and indicators. Confirm that the equipment, including all safety devices (guards, interlocks, etc.), is in good working order and that the required environmental conditions exist. Use the personal protective equipment (PPE) specified for each task. Refer to Equipment Safety Information or the material manufacturer s instructions and MSDS for PPE requirements. Do not use equipment that is malfunctioning or shows signs of a potential malfunction Nordson Corporation A1EN01[XXSAFE]10

16 1-6 Safety Maintenance and Repair Practices Perform scheduled maintenance activities at the intervals described in this document. Relieve system hydraulic and pneumatic pressure before servicing the equipment. De-energize the equipment and all auxiliary devices before servicing the equipment. Use only new or factory-authorized refurbished replacement parts. Read and comply with the manufacturer s instructions and the MSDS supplied with equipment cleaning compounds. NOTE: MSDSs for cleaning compounds that are sold by Nordson are available at or by calling your Nordson representative. Confirm the correct operation of all safety devices before placing the equipment back into operation. Dispose of waste cleaning compounds and residual process materials according to governing regulations. Refer to the applicable MSDS or contact the authority having jurisdiction for information. Keep equipment safety warning labels clean. Replace worn or damaged labels. A1EN01[XXSAFE] Nordson Corporation

17 Safety 1-7 Equipment Safety Information This equipment safety information is applicable to the following types of Nordson equipment: hot melt and cold adhesive application equipment and all related accessories pattern controllers, timers, detection and verification systems, and all other optional process control devices Equipment Shutdown To safely complete many of the procedures described in this document, the equipment must first be shut down. The level of shut down required varies by the type of equipment in use and the procedure being completed. If required, shut down instructions are specified at the start of the procedure. The levels of shut down are: Relieving System Hydraulic Pressure Completely relieve system hydraulic pressure before breaking any hydraulic connection or seal. Refer to the melter-specific product manual for instructions on relieving system hydraulic pressure. De-energizing the System Isolate the system (melter, hoses, guns, and optional devices) from all power sources before accessing any unprotected high-voltage wiring or connection point. 1. Turn off the equipment and all auxiliary devices connected to the equipment (system). 2. To prevent the equipment from being accidentally energized, lock and tag the disconnect switch(es) or circuit breaker(s) that provide input electrical power to the equipment and optional devices. NOTE: Government regulations and industry standards dictate specific requirements for the isolation of hazardous energy sources. Refer to the appropriate regulation or standard Nordson Corporation A1EN01[XXSAFE]10

18 1-8 Safety Disabling the Guns All electrical or mechanical devices that provide an activation signal to the guns, gun solenoid valve(s), or the melter pump must be disabled before work can be performed on or around a gun that is connected to a pressurized system. 1. Turn off or disconnect the gun triggering device (pattern controller, timer, PLC, etc.). 2. Disconnect the input signal wiring to the gun solenoid valve(s). 3. Reduce the air pressure to the gun solenoid valve(s) to zero; then relieve the residual air pressure between the regulator and the gun. A1EN01[XXSAFE] Nordson Corporation

19 Safety 1-9 General Safety Warnings and Cautions Table 1-1 contains the general safety warnings and cautions that apply to Nordson hot melt and cold adhesive equipment. Review the table and carefully read all of the warnings or cautions that apply to the type of equipment described in this manual. Equipment types are designated in Table 1-1 as follows: HM = Hot melt (melters, hoses, guns, etc.) PC = Process control CA = Cold adhesive (dispensing pumps, pressurized container, and guns) Equipment Type HM Table 1-1 General Safety Warnings and Cautions Warning or Caution WARNING: Hazardous vapors! Before processing any polyurethane reactive (PUR) hot melt or solvent-based material through a compatible Nordson melter, read and comply with the material s MSDS. Ensure that the material s processing temperature and flashpoints will not be exceeded and that all requirements for safe handling, ventilation, first aid, and personal protective equipment are met. Failure to comply with MSDS requirements can cause personal injury, including death. HM WARNING: Reactive material! Never clean any aluminum component or flush Nordson equipment with halogenated hydrocarbon fluids. Nordson melters and guns contain aluminum components that may react violently with halogenated hydrocarbons. The use of halogenated hydrocarbon compounds in Nordson equipment can cause personal injury, including death. HM, CA WARNING: System pressurized! Relieve system hydraulic pressure before breaking any hydraulic connection or seal. Failure to relieve the system hydraulic pressure can result in the uncontrolled release of hot melt or cold adhesive, causing personal injury. HM WARNING: Molten material! Wear eye or face protection, clothing that protects exposed skin, and heat-protective gloves when servicing equipment that contains molten hot melt. Even when solidified, hot melt can still cause burns. Failure to wear appropriate personal protective equipment can result in personal injury. Continued Nordson Corporation A1EN01[XXSAFE]10

20 1-10 Safety General Safety Warnings and Cautions (contd) Table 1-1 General Safety Warnings and Cautions (contd) Equipment Type HM, PC Warning or Caution WARNING: Equipment starts automatically! Remote triggering devices are used to control automatic hot melt guns. Before working on or near an operating gun, disable the gun s triggering device and remove the air supply to the gun s solenoid valve(s). Failure to disable the gun s triggering device and remove the supply of air to the solenoid valve(s) can result in personal injury. HM, CA, PC WARNING: Risk of electrocution! Even when switched off and electrically isolated at the disconnect switch or circuit breaker, the equipment may still be connected to energized auxiliary devices. De-energize and electrically isolate all auxiliary devices before servicing the equipment. Failure to properly isolate electrical power to auxiliary equipment before servicing the equipment can result in personal injury, including death. CA WARNING: Risk of fire or explosion! Nordson cold adhesive equipment is not rated for use in explosive environments and should not be used with solvent-based adhesives that can create an explosive atmosphere when processed. Refer to the MSDS for the adhesive to determine its processing characteristics and limitations. The use of incompatible solvent-based adhesives or the improper processing of solvent-based adhesives can result in personal injury, including death. HM, CA, PC WARNING: Allow only personnel with appropriate training and experience to operate or service the equipment. The use of untrained or inexperienced personnel to operate or service the equipment can result in injury, including death, to themselves and others and can damage to the equipment. Continued... A1EN01[XXSAFE] Nordson Corporation

21 Safety 1-11 Equipment Type HM Warning or Caution CAUTION: Hot surfaces! Avoid contact with the hot metal surfaces of guns, hoses, and certain components of the melter. If contact can not be avoided, wear heat-protective gloves and clothing when working around heated equipment. Failure to avoid contact with hot metal surfaces can result in personal injury. HM CAUTION: Some Nordson melters are specifically designed to process polyurethane reactive (PUR) hot melt. Attempting to process PUR in equipment not specifically designed for this purpose can damage the equipment and cause premature reaction of the hot melt. If you are unsure of the equipment s ability to process PUR, contact your Nordson representative for assistance. HM, CA CAUTION: Before using any cleaning or flushing compound on or in the equipment, read and comply with the manufacturer s instructions and the MSDS supplied with the compound. Some cleaning compounds can react unpredictably with hot melt or cold adhesive, resulting in damage to the equipment. HM CAUTION: Nordson hot melt equipment is factory tested with Nordson Type R fluid that contains polyester adipate plasticizer. Certain hot melt materials can react with Type R fluid and form a solid gum that can clog the equipment. Before using the equipment, confirm that the hot melt is compatible with Type R fluid Nordson Corporation A1EN01[XXSAFE]10

22 1-12 Safety Other Safety Precautions Do not use an open flame to heat hot melt system components. Check high pressure hoses daily for signs of excessive wear, damage, or leaks. Never point a dispensing handgun at yourself or others. Suspend dispensing handguns by their proper suspension point. First Aid If molten hot melt comes in contact with your skin: 1. Do NOT attempt to remove the molten hot melt from your skin. 2. Immediately soak the affected area in clean, cold water until the hot melt has cooled. 3. Do NOT attempt to remove the solidified hot melt from your skin. 4. In case of severe burns, treat for shock. 5. Seek expert medical attention immediately. Give the MSDS for the hot melt to the medical personnel providing treatment. A1EN01[XXSAFE] Nordson Corporation

23 Safety 1-13 Special Safety Instructions Safety Labels on the Gun The following safety labels are affixed to the adhesive gun: WARNING: Risk of electrical shock. Failure to observe may result in personal injury, death, or equipment damage. Safety Instructions in the Manual The following pictographs and the respective safety instructions are used in the manual: WARNING: Risk of electrical shock. Failure to observe may result in personal injury, death, or equipment damage. WARNING: Hot! Risk of burns. Wear heat-protective gloves. WARNING: Hot! Risk of burns. Wear safety goggles and heat-protective gloves. WARNING: System or material pressurized. Relieve pressure. Failure to observe may result in serious burns. CAUTION: Non-observance can result in damage to the equipment or accessories Nordson Corporation

24 1-14 Safety This page intentionally left blank Nordson Corporation

25 Description 2-1 Section 2 Description Intended Use The series liquid adhesive guns subsequently also referred to as guns have been specially designed for the application of water-based adhesives. They can be used for non-contact glue application. Any other use is considered unintended use. The manufacturer is not liable for personal injury or property damage resulting from unintended use. Intended use includes observing the manufacturer s prescribed operating, maintenance and service regulations. The product described here may only be operated, serviced and maintained by persons who are familiar with the product and have been informed of the hazards involved. The respective rules for prevention of accidents as well as any other commonly recognized safety regulations and industrial health regulations must be observed. Unintended Use Examples The adhesive guns may not be used under the following conditions: In a defective condition In a potentially explosive atmosphere When the housing is open or protective equipment is removed In surroundings which do not correspond to the unit s Degree of Protection With unauthorized modifications. The guns may not be used to process the following materials: Explosive and flammable materials Materials sensitive to pressure Food products Nordson Corporation

26 2-2 Description Safety Instructions Residual Risks Prior to installation and first operation of the system, it is essential to read and follow the safety instructions. The general safety instructions are enclosed as an annex to the documentation folder or they are a section of this manual. The specific safety instructions are part of this manual. Nordson knows of no residual risks. General Information Updated Bill of Material The electrically controlled adhesive guns are designed for the application of water-based adhesives. They are particularly suited to the fast, intermittent, non-contact application of adhesive. After switching on the power to the coils inside the adhesive gun, the nozzle needle is raised, thus opening the nozzle. When the power is switched off, a spring forces the needle down, closing the nozzle. The needle stroke can be adjusted by means of an adjustable pole face which can even be turned during operation. A mounting bracket is available which can secure the adhesive gun in practically all working positions. The mounting brackets described in this section relate to standard mounting brackets where reference is not made to any other units. Individual applications require individual solutions. In such cases, please contact Nordson. Refer to the updated Bill of Material enclosed with your equipment. For further questions, please contact Nordson Nordson Corporation

27 Description 2-3 Functioning The following figure illustrates the basic method of operation of an adhesive gun within a complete system. Adhesive is to be applied to a substrate (7). The transport belts (8) convey the substrates. When the leading edge of a substrate reaches the photocell (10), the beam of light sent is reflected and the program is started. The control unit compiles all the data according to the speed of the production machine. The encoder (4) is mechanically connected to the transport equipment via a gear and supplies one pulse per mm. The control unit evaluates all the data and establishes the point at which the liquid adhesive guns (5) must be activated. The pump (12) is connected to the compressed air supply (1). It operates continuously and pumps the liquid adhesive from the adhesive reservoir (11) to the liquid adhesive guns (5). A current between 0-20 ma is supplied from the control unit (3) to the proportional pressure control valve (2). The strength of the current is dependent on the speed of the production machine. The strength of the current determines how far the proportional pressure control valve (2) should be opened and the regulator (9) opens accordingly. The adhesive flows to the liquid adhesive guns (5) and is applied to the substrate. The length of the application is defined by the control unit program Nordson Corporation

28 2-4 Description Functioning (contd.) Electric Compressed air Adhesive 11 8 O615 Fig. 2-1 Principle Drawing 1 Compressed air feed 2 Proportional pressure control valve 3 Control unit 4 Encoder 5 Liquid adhesive gun 6 Adhesive pattern 7 Substrate 8 Transport belts 9 LA380 adhesive pressure regulator 10 Photocell 11 Adhesive reservoir 12 LA300 adhesive pump 2007 Nordson Corporation

29 Description 2-5 Method of Operation Components LA 820 When a peak voltage is applied to the magnetic coil in the adhesive gun, the needle in the module moves from its home position, thus opening the nozzle. A holding voltage retains the needle in this position. When the holding voltage is switched off, a correspondingly pretensioned spring moves the needle back and closes the opening O616 Fig. 2-2 LA 820 Adhesive Gun 1 Adhesive connection 2 Protective cap 3 Electrical connection 4 Adjustable pole face 5 Module 6 Sleeve nut with nozzle 7 Manifold 8 Mounting bracket 9 Fixing screw 2007 Nordson Corporation

30 2-6 Description LA 820 RC LogiComm O617 Fig. 2-3 LA 820 RC LogiComm Adhesive Gun 1 Adhesive connection with glue filter 4 Adjustable pole face 2 Protective cap 5 Module 3 Electrical connection 6 Nozzle 7 Manifold 8 Fixing screw LA 820 RC LA4xx O618 Fig. 2-4 LA 820 RC LA4xx Adhesive Gun 1 Adhesive connection with glue filter 4 Adjustable pole face 2 Protective cap 5 Module 3 Electrical connection 6 Nozzle 7 Manifold 8 Fixing screw 2007 Nordson Corporation

31 Installation 3-1 Section 3 Installation WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. WARNING: Disconnect power to the control unit before connecting coil leads. Failure to do so may result in death. Unpacking Transport Storage Disposal Unpack carefully. Then check for any damage caused during shipping. Reuse packaging materials or dispose of properly according to local regulations. The liquid adhesive gun is fully preassembled at the factory (refer to Components in Section Description). The LA 820 adhesive gun is supplied without a nozzle, whereas adhesive guns of the type LA 820 RC are supplied with a nozzle. The adhesive gun is a high precision, valuable part. Handle very carefully! Protect the nozzle from damage, e.g. with the original packaging. Do not store outside! Protect from humidity and dust. Do not lay the unit on the nozzle. Protect the nozzle from damage, e.g. by placing it in the original packaging. When your Nordson product has exhausted its purpose and/or is no longer needed, dispose of it properly according to local regulations Nordson Corporation

32 3-2 Installation Installation Connecting Material Lines Electrical Lines Due to possible self-vibrations caused by intermittent operation, the liquid adhesive gun should be installed as firmly as possible. The transmission of vibrations from the production machine to the gun should be avoided as much as possible. The guns should be installed in an easily accessible location because they need to be removed for cleaning and maintenance purposes. NOTE: In general, a production machine refers to a machine in which Nordson equipment for adhesive application is integrated (e.g. a packing machine). The term production machine means the same as parent machine which may appear in other Nordson literature. The connections used most frequently are described in the following. In some cases, e.g. for enclosed operation or under clean room conditions, deviations from these instructions may be necessary. Remove the protective cap (2). Connect the material hose coming from the pressurized adhesive tank or pump to the adhesive connection (1) on the liquid adhesive gun. WARNING: Disconnect power to the control unit before connecting the electrical lines. Failure to do so may result in death. Connect the connection cable from the control unit to the connection socket (3) on the liquid adhesive gun Nordson Corporation

33 Installation LA 820 LA 820 RC LogiComm O619 Fig. 3-1 Installing and Connecting the Adhesive Guns 1 Adhesive connection 2 Protective cap 3 Electrical connection 4 Adjustable pole face 5 Fixing screw 6 Mounting bracket 2007 Nordson Corporation

34 3-4 Installation Setting the Adhesive Quantity, LA 820 The adhesive pattern is influenced by the adhesive pressure and adhesive quantity. The adhesive pressure is determined by the pump control unit according to the application speed. Fig. 3-2 O620 The adhesive gun is equipped with an adjustable pole face to adjust the adhesive quantity (4, Fig. 3-1). Turn the adjustable pole face counterclockwise using an Allen key to increase the quantity of adhesive. Reduce the quantity of adhesive by turning the key clockwise. The upper side of the adhesive gun (Fig. 3-1) is provided with reference points which indicate the setting of the adjustable pole face. Turning the adjustable pole face one graduation point adjusts the needle stroke by 0.05 mm ( ). NOTE: The default needle stroke setting is 0.15 mm ( ). To achieve this setting, turn the adjustable pole face to its bottom setting and then 3 graduations back. NOTE: Increasing the needle stroke reduces the maximum adhesive pressure. When operating at high speeds, the length of the adhesive bead is increased and, therefore, requires greater compensation. Setting the Adhesive Quantity, LA 820 RC The adhesive pattern is influenced by the adhesive pressure and adhesive quantity. The adhesive pressure is determined by the pump control unit according to the application speed. Fig. 3-3 O621 The LA 820 RC adhesive gun is equipped with an adjustable pole face to adjust the adhesive quantity (4, Fig. 3-1). Turn the adjustable pole face counterclockwise to increase the quantity of adhesive. Reduce the quantity of adhesive by turning the key clockwise. Turning the adjustable pole face one click adjusts the needle stroke by 0.02 mm ( ). The reference points are not applicable. NOTE: The default needle stroke setting is achieved by turning the adjustable pole face down fully and then turning it back 8 clicks. The adjustable pole face should be turned back a maximum of 10 clicks and a minimum of 4 clicks. NOTE: Increasing the needle stroke reduces the maximum adhesive pressure. When operating at high speeds, the length of the adhesive bead is increased and, therefore, requires greater compensation Nordson Corporation

35 Installation 3-5 Mounting Brackets The mounting bracket illustrated in Fig. 3-4 is available for securing the adhesive gun Fig. 3-4 Mounting Bracket with Adhesive Gun 1 Folding carton bracket, 3 Liquid adhesive gun LA820 RC P/N , for gun LA820 RC 4 Adapter for GD100 glue sensor, and photocell LA650 P/N Photocell LA650 5 Glue sensor GD Nordson Corporation

36 3-6 Installation 2007 Nordson Corporation

37 Operation 4-1 Section 4 Operation WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. General Adhesive Processing Instructions NOTE: The following information is particularly important for the processing of liquid adhesives but is also applicable to other materials: Always pre-test the product before applying it for its ultimate purpose. The surface to be bonded should be at room temperature and free of dust, grease and moisture. The suitability of material, optimum working conditions and any necessary pre-treatment of the substrate must be determined by testing. Some substrates contain softeners and other components which may become volatile later. Occasionally, surfaces are covered with wax, isolating oil, etc. The bonding may fail immediately or later if pre-treatment/tests are not carried out. NOTE: Observe any comment sheets concerning the process to the material used. Compatibility of Different Types of Adhesives NOTE: Not all types of liquid adhesive are compatible. The adhesive may become degraded if improperly used, resulting in functional faults and, possibly, equipment damage. In our capacity as suppliers of adhesive guns, we assume no liability for damage to equipment, hoses and guns caused by the hardening of adhesive through improper handling. In case of doubt and/or intended change of adhesive, please contact the adhesive supplier, us or one of our representatives Nordson Corporation

38 4-2 Operation Switching Off in an Emergency Familiarize yourself thoroughly in respect of behavior in emergency situations and with the location and activation of the Emergency Stop operating elements installed in the production area. WARNING: Press the Emergency Stop switch immediately in any emergency situation. Initial Startup 1. Trigger the nearest EMERGENCY STOP element (EMERGENCY STOP button, EMERGENCY STOP ripcord or main switch with EMERGENCY STOP function). 2. Locate and clear the cause of the Emergency Stop situation before switching the system on again. 1. Set the air pressure on the pump so that the max. hydraulic pressure is not exceeded. Liquid adhesive gun LA 820 LA 820 RC Max. hydraulic pressure 20 bar (290 PSI) 25 bar (362 PSI) NOTE: A higher pressure may damage the liquid adhesive gun. 2. Place a collecting vessel underneath the gun and switch on the control unit. 3. Setup the control unit so that the adhesive flows out of the gun nozzle evenly and without any air bubbles. 4. Carry out test gluing and check the adhesive bead. If a thicker bead is required, the pressure can be increased but not in excess of the maximum hydraulic pressure. Daily Startup 1. Check whether there is sufficient adhesive in the reservoir. 2. Release the air pressure for the pump. Daily Shutdown 1. Shut off the compressed air supply to the pump (reduce to 0 bar). 2. Close the nozzle orifices with silicone paste, Nordson P/N Nordson Corporation

39 Maintenance 5-1 Section 5 Maintenance WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. The adhesive gun is easy to maintain and, in general, maintenance-free. Under normal conditions, all the components have a long service life. WARNING: Disconnect the power supply! WARNING: Shut off the adhesive supply. WARNING: When possible, always wear protective gloves when carrying out the work. Always observe the following basic points: Ensure that the material to be applied is in a clean, filtered condition. Individual operating conditions and different application materials require a corresponding minimum effort for maintenance. Do not use metallic, sharp-edged tools to clean the outside of the equipment, e.g. nozzle tips, only use soft brushes. When carrying out repair or maintenance work, keep the working space as well as the gun to be repaired as clean as possible. Adhesive guns which are soiled should be thoroughly flushed through when the opportunity occurs. This is possible particularly when the nozzle needle or material nozzles need to be replaced. The adhesive guns should not remain installed for any important maintenance work but be removed from the machine. Depressurize the material supply lines beforehand Nordson Corporation

40 5-2 Maintenance Preventive Maintenance Cleaning the Liquid Adhesive Gun Regular Maintenance It is not necessary to clean the adhesive gun if air is prevented from entering into the hydraulic system and coming into contact with the glue. If this occurs, however, the glue starts to solidify after approx. 30 minutes. The precise time varies according to the adhesive used. Blocked nozzle orifices or guns can be cleaned easily at any time. NOTE: Do not disassemble an adhesive gun in which glue has solidified! It is highly likely this would damage sensitive components. We recommend immersing the adhesive gun in warm water for 1-2 days to soften the glue. Repeat the process several times, if necessary. If the adhesive gun still cannot be disassembled, return it to us for repair. We recommend flushing the liquid adhesive guns with water twice a year. The guns should always be kept clean, residual glue and dirt being removed daily Nordson Corporation

41 Maintenance 5-3 Disassembling the LA 820 Liquid Adhesive Gun WARNING: Disconnect the power supply. WARNING: The system and material are pressurized. Shut off the compressed air supply! Otherwise, there is a considerable risk of injury. Refer to figure Prepare a vessel with water. 2. Ensure that the working area and all the tools are clean. NOTE: Foreign bodies can damage gaskets and seal fits causing leaks. 3. Place a collecting vessel under the application head. 4. Disconnect the adhesive hose from the adhesive connection (14). Seal the adhesive hose with adhesive tape or plugs so that no adhesive can escape. 5. Loosen the two fixing screws (13) and remove the manifold (12) from the adhesive gun. Remove the sealing ring (11). 6. Remove the sleeve nut (10). 7. Remove the seat (9). 8. Remove the O-ring (8) from the seat. 9. Remove the needle (7) and compression spring (6) from the adhesive gun. 10. Screw the adjustable pole face (3) from the adhesive gun and remove the compression spring (5) and washer (2). 11. Remove the O-ring (4) from the adjustable pole face. 12. Clean all parts with water. NOTE: The electrical coils and electrical connection cannot be removed. WARNING: Do not remove the hollow bolt (15) from the housing. The adhesive gun would be damaged as a result Nordson Corporation

42 5-4 Maintenance O623 Fig. 5-1 Disassembling the LA 820 Liquid Adhesive Gun 1 Housing 6 Compression spring 2 Washer 7 Needle 3 Adjustable pole face 8 O-ring 4 O-ring 9 Seat 5 Compression spring 10 Sleeve nut 11 Sealing ring 12 Manifold 13 Fixing screw 14 Hose nipple 15 Hollow bolt 2007 Nordson Corporation

43 Maintenance 5-5 Disassembling the LA 820 RC Liquid Adhesive Gun The instructions for disassembling the adhesive gun apply to the LA 820 RC LA4xx and LA 820 RC Logicomm liquid adhesive guns. WARNING: Disconnect the power supply. WARNING: The system and material are pressurized. Shut off the compressed air supply! Otherwise, there is a considerable risk of injury. Refer to figure Prepare a vessel with water. 2. Ensure that the working area and all the tools are clean. NOTE: Foreign bodies can damage gaskets and seal fits causing leaks. 3. Place a collecting vessel under the application head. 4. Disconnect the adhesive hose from the adhesive connection (11). Seal the adhesive hose with adhesive tape or plugs so that no adhesive can escape. 5. Loosen the two fixing screws (10) and remove the manifold (9) from the adhesive gun. Remove the sealing ring (8). 6. Unscrew the nozzle (7). 7. Remove the O-ring (6) from the nozzle. 8. Remove the needle (5) and compression spring (4) from the adhesive gun. 9. Unscrew the adjustable pole face (2) from the adhesive gun. 10. Remove the O-ring (3) from the adjustable pole face. 11. Clean all parts with water. NOTE: The electrical coils and electrical connection cannot be removed. NOTE: The adjustable pole face cannot be disassembled. WARNING: Do not remove the hollow bolt (13) from the housing. The adhesive gun would be damaged as a result Nordson Corporation

Sponge Cleaner. Manual P/N A English. Issued 05/03 NORDSON (UK) LTD STOCKPORT

Sponge Cleaner. Manual P/N A English. Issued 05/03 NORDSON (UK) LTD STOCKPORT Sponge Cleaner Manual P/N 768 651 A English Issued 05/03 NORDSON (UK) LTD STOCKPORT Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which is protected

More information

Level Monitor LA 100

Level Monitor LA 100 Level Monitor LA 100 Manual English NORDSON BENELUX MAASTRICHT THE NETHERLANDS www.nordson.com Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which

More information

Seal Sentry Series 10 Bead Detection System

Seal Sentry Series 10 Bead Detection System Seal Sentry Series 10 Bead Detection System Customer Product Manual P/N 321 289D02 This equipment is regulated by the European Union under WEEE Directive 2002/96/EC). See www.nordson.com for information

More information

DuraDrum Bulk Melters DD200

DuraDrum Bulk Melters DD200 DuraDrum Bulk Melters Manual English Issued 11/07 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice This

More information

Electropneumatic Hot Melt Application Heads EP 34 / EP 34 S / EP 34 SD

Electropneumatic Hot Melt Application Heads EP 34 / EP 34 S / EP 34 SD Electropneumatic Hot Melt Application Heads Manual P/N 409 090 A English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson

More information

Hot Melt Application Head Series PW...

Hot Melt Application Head Series PW... Hot Melt Application Head Series... Manual English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice This

More information

Series AD-31 and Series L4 Extrusion Handguns

Series AD-31 and Series L4 Extrusion Handguns Series AD-31 and Series L4 Extrusion Handguns Customer Product Manual Issued 5/05 NORDSON CORPORATION DULUTH, GEORGIA USA www.nordson.com For CE Declaration, refer to melter documentation. Nordson Corporation

More information

GD-500 Bead Detection System

GD-500 Bead Detection System GD-500 Bead Detection System Customer Product Manual Issued 4/08 NORDSON CORPORATION DULUTH, GEORGIA USA www.nordson.com Nordson Corporation welcomes requests for information, comments, and inquiries about

More information

Hot Melt Material Applicator MC 7

Hot Melt Material Applicator MC 7 Hot Melt Material Applicator MC 7 Parts List P/N 735003A English Issued 2/06 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation

More information

U7698E Flame Detector

U7698E Flame Detector U7698E Flame Detector Customer Product Manual Issued 3/02 NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments, and inquiries about its products. General

More information

Hot Melt Material Applicator MC 6

Hot Melt Material Applicator MC 6 Hot Melt Material Applicator Manual P/N 403 022 D English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice

More information

Hot Melt Applicators SB60 BoD

Hot Melt Applicators SB60 BoD Hot Melt Applicators Manual - English - Edition 06/14 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This document applies to the entire series. Order number P/N = Order number for Nordson articles Note

More information

Hot Melt Material Applicator MC 4420

Hot Melt Material Applicator MC 4420 Hot Melt Material Applicator Manual English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice This is

More information

Fill Sentry. Automated Fill System. Customer Product Manual Part A. NORDSON CORPORATION

Fill Sentry. Automated Fill System. Customer Product Manual Part A. NORDSON CORPORATION Fill Sentry Automated Fill System Customer Product Manual Part NORDSON CORPORATION www.nordson.com CAUTION: If this equipment is used with other Nordson equipment, refer to the manuals provided with that

More information

Hot Melt Applicator MC 405 for Foil Bags

Hot Melt Applicator MC 405 for Foil Bags Hot Melt Applicator for Foil Bags Manual English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY NOTE This manual is for products with the following P/N: 8015767 8022490 8027924 8037680 8018042 8023117 8031127

More information

FillEasy C Adhesive Feed System

FillEasy C Adhesive Feed System FillEasy C Adhesive Feed System Customer Product Manual Issued 5/10 This document contains important safety information Be sure to read and follow all safety information in this document and any other

More information

Bulk Melters BM 200 with Piston Pump - EASY Pneumatics -

Bulk Melters BM 200 with Piston Pump - EASY Pneumatics - Bulk Melters BM 200 with Piston Pump - EASY Pneumatics - Manual - English - Issued 05/06 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note After approx. December 2003, this manual applies to the entire series.

More information

Bulk Melters BM 200 with Piston Pump for 200 l Drums

Bulk Melters BM 200 with Piston Pump for 200 l Drums Bulk Melters BM 200 with Piston Pump for 200 l Drums Manual P/N 464 937 B - English - NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number

More information

Bulk Melters BM 200 with Gear/Gerotor Pump for 200 l Drums

Bulk Melters BM 200 with Gear/Gerotor Pump for 200 l Drums Bulk Melters BM 200 with Gear/Gerotor Pump for 200 l Drums Manual P/N 464 958 C - English - NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order

More information

Drum Melters DG 21 / DG 201

Drum Melters DG 21 / DG 201 Drum Melters DG 21 / DG 201 Manual P/N 464 839 A - English - NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products

More information

AltaSpray Plus Applicators

AltaSpray Plus Applicators AltaSpray Plus Applicators Customer Product Manual Issued 5/3 This document contains important safety information Be sure to read and follow all safety information in this document and any other related

More information

Hot Melt Material Applicator MC 12 / MC 24

Hot Melt Material Applicator MC 12 / MC 24 Hot Melt Material Applicator Manual P/N 403 076 D English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice

More information

Envirocoat Twin Cyclone Powder Coating Booth

Envirocoat Twin Cyclone Powder Coating Booth Envirocoat Twin Cyclone Powder Coating Booth Manual P/N 779166 --English-- Keep for Future Reference Nordson China Sourcing - Shanghai Trademarks AccuJet, Aquaguard, Asymtek, Automotive, Autotech, Blue

More information

Hot-melt adhesive extruder EEX40

Hot-melt adhesive extruder EEX40 Hot-melt adhesive extruder EEX40 Manual 110900563/001 - English - Nordson Deutschland GmbH Buchholz-Mendt GERMANY Note This manual applies to the entire series. Part number P/N = 7549584 Notice This is

More information

ColorMax. Engineered Booth. Customer Product Manual P/N A. Issued 11/10

ColorMax. Engineered Booth. Customer Product Manual P/N A. Issued 11/10 ColorMax Engineered Booth Customer Product Manual Issued 11/10 For parts and technical support, call your nearest Finishing Customer Support Centre. Find your nearest centre at www.nordson.com/directory

More information

Fluidking. Manual P/N A English NORDSON (UK) LIMITED STOCKPORT UK

Fluidking. Manual P/N A English NORDSON (UK) LIMITED STOCKPORT UK Manual P/N 768 643 A English NORDSON (UK) LIMITED STOCKPORT UK Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which is protected by copyright. Original

More information

Bulk Melters AltaPail

Bulk Melters AltaPail Bulk Melters AltaPail Manual - English - Edition 02/12 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This document is for products with the following P/N: 7165698 7157455 7157502 7157503 Order number

More information

Powder Conditioning System

Powder Conditioning System Powder Conditioning System Manual P/N 779168 --English-- Keep for Future Reference Nordson China Sourcing - Shanghai Table I Trademarks AccuJet, Aquaguard, Asymtek, Automotive, Autotech, Blue Box, CF,

More information

Liquid Adhesive Detection System Alarm Box

Liquid Adhesive Detection System Alarm Box Liquid Adhesive Detection System Alarm Box Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products.

More information

Hot-melt adhesive extruder EEX100

Hot-melt adhesive extruder EEX100 Hot-melt adhesive extruder EEX100 Manual 111121287/001 -- English -- NordsonDeutschlandGmbHBuchholz--MendtGERMANY Note This manual applies to the entire series. Part number P/N = 7552471 Notice This is

More information

Fixed Reclaim System

Fixed Reclaim System Fixed Reclaim System Manual P/N 779163 --English-- Keep for Future Reference Nordson China Sourcing - Shanghai Trademarks AccuJet, Aquaguard, Asymtek, Automotive, Autotech, Blue Box, CF, Can Works, Century,

More information

Non-RTD Hot Melt Hose Replacement

Non-RTD Hot Melt Hose Replacement Instruction Sheet P/N 7C 0 Safety WARNING: System pressurized! Relieve system hydraulic pressure before breaking any hydraulic connection or seal. Failure to relieve the system hydraulic pressure can result

More information

55-Gallon Dispenser Package

55-Gallon Dispenser Package INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. 308 666 Rev. A Husky 715 55-Gallon Dispenser Package 100 psi (6.9 bar) Maximum

More information

Hot -melt adhesive extruder EEX100 -F5B2X2TWXMQXS

Hot -melt adhesive extruder EEX100 -F5B2X2TWXMQXS Hot -melt adhesive extruder EEX100 -F5B2X2TWXMQX Manual 110717869/001 -- English -- Nordson Deutschland GmbH D Buchholz--Mendt D GERMANY Note This manual applies to the entire series. erial no. 110717869/001

More information

FC-2200 Flame Detector

FC-2200 Flame Detector FC-2200 Flame Detector Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products. Address all correspondence

More information

CleanSpray System Operation

CleanSpray System Operation Nordson Corporation OPERATOR S CARD P/N 108684C CleanSpray System Operation Introduction The individual manuals for the CleanSpray Gun, CleanSpray Controller and Model 25B Pump are included with each component.

More information

Replacing a Gun Thermostat

Replacing a Gun Thermostat Instruction Sheet Replacing a Gun Thermostat WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation.

More information

Big Box Virgin Powder Feed System

Big Box Virgin Powder Feed System Manual P/N 315 852 C -- English -- Keep for Future Reference NORDON (UK) LTD. D TOCKPORT Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which is protected

More information

K Operating Instructions. Before first use of the unit read these operating instructions and act in accordance with them.

K Operating Instructions. Before first use of the unit read these operating instructions and act in accordance with them. K 1.100 Operating Instructions Before first use of the unit read these operating instructions and act in accordance with them. www.kaercher.com/register-and-win 59651430 (10/13) Contents General information..............

More information

Operational Instructions. Glue Applicator MS Translation from German to English

Operational Instructions. Glue Applicator MS Translation from German to English Operational Instructions Glue Applicator MS 200 Translation from German to English Table of Contents Product Description 1 General Safety Instructions 2 Safety Measures to be taken during Operation 3 Start-up

More information

Product Manual Glue Applicators MS 80 and MS 200

Product Manual Glue Applicators MS 80 and MS 200 Product Manual www.pakarte.com Glue Applicators MS 80 and MS 00 Translation from German to English Table of Contents Product Description General Safety Instructions Safety Measures to be taken during Operation

More information

Page 1 of 18. Part# /5/2013

Page 1 of 18. Part# /5/2013 Part# 1002655-06 8/5/2013 This manual contains important information concerning the installation and operation of the gun washers listed above. Read manual thoroughly and keep for future reference INSTRUCTIONS

More information

INSTRUCTION MANUAL W-400

INSTRUCTION MANUAL W-400 USE and MAINTENANCE INSTRUCTION MANUAL Bellaria WBX WB GRAVITY SPRAY GUN Series LPH-400 WB en it fr es pt de se TECHNICAL DATA Classic Plus Series LPH-400 (LVLP) Classic Plus Nozzle_Needle set Combination

More information

55-Gallon Dispenser Package

55-Gallon Dispenser Package INSTRUCTIONS-PARTS LIST Husky 515 55-Gallon Dispenser Package 08666 Rev.C INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. 100 psi(6.9 bar) Maximum Air

More information

Models: GW/R-T GW/R-2-T GW/R-3-T

Models: GW/R-T GW/R-2-T GW/R-3-T Part# GW/R-T-OM 1/12/04 TN Models: GW/R-T GW/R-2-T GW/R-3-T This manual contains important information concerning the installation and operation of the gun washers listed above. Read manual thoroughly

More information

Upholstery and Drapery Cleaner. Operator and Parts Manual. Model No.: gal Extractor. MNL32506 Rev. 00 (08-98)

Upholstery and Drapery Cleaner. Operator and Parts Manual. Model No.: gal Extractor. MNL32506 Rev. 00 (08-98) 32506 Upholstery and Drapery Cleaner Model No.: 32506 3 gal Extractor Operator and Parts Manual KLEENRITE 1122 MAPLE STREET MADERA CA 93637 U.S.A. FAX: 1-559-673-5725 CUSTOMER SERVICE: 1-800-241-4865 MNL32506

More information

CT-930CH, CT-930LPCH and CT-940CH TABLE OF CONTENTS

CT-930CH, CT-930LPCH and CT-940CH TABLE OF CONTENTS CT-930CH, CT-930LPCH and CT-940CH PA22141A01 Rev. 03 5-2012 REMOTE HYDRAULIC COMPRESSION TOOLS Panduit Corp. 2012 TABLE OF CONTENTS SYSTEM SPECIFICATIONS... 1 OPTIONAL ACCESSORIES... 2 PRECAUTIONS AND

More information

Remote Temperature Controller

Remote Temperature Controller Remote Temperature Controller Technical Manual Part 07 97A NORDSON CORPORATION. AMHERST, OHIO. USA Nordson Corporation welcomes requests for information, comments and inquiries about its products. Address

More information

OWNER S MANUAL. Models: Herkules Equipment Corporation 2760 Ridgeway Court Walled Lake, MI USA Fax

OWNER S MANUAL. Models: Herkules Equipment Corporation 2760 Ridgeway Court Walled Lake, MI USA Fax Part# 1000692 7/12/99 tn INSTRUCTIONS This manual contains important information concerning the installation and operation of the gun washers listed at the right. Read manual thoroughly and keep for future

More information

AIR LINE HEATER / FILTER HEATER MODEL: A13230

AIR LINE HEATER / FILTER HEATER MODEL: A13230 SERVICE MANUAL February - 2014 AIR LINE HEATER / FILTER HEATER MODEL: A13230 IMPORTANT: Before using this equipment, carefully read SAFETY PRECAUTIONS, starting on page 1, and all instructions in this

More information

USE and MAINTENANCE INSTRUCTION MANUAL GRAVITY. WS-400 EVO LS-400 Entech. SPRAY GUN Series. en it fr es pt de se

USE and MAINTENANCE INSTRUCTION MANUAL GRAVITY. WS-400 EVO LS-400 Entech. SPRAY GUN Series. en it fr es pt de se USE and MAINTANCE INSTRUCTION MANUAL WS-400 EVO LS-400 Entech GRAVITY SPRAY GUN Series en it fr es pt de se TECHNICAL DATA WS-400 WS-400 EVO WS-400 Clear WS-400 Base WS-400-1301 EVO 1.3 170 365 260 WS-400-1401

More information

Dyna-Star HP or HF Pump 35# Pail Kit and Follower Plate

Dyna-Star HP or HF Pump 35# Pail Kit and Follower Plate Instructions Dyna-Star HP or HF Pump 35# Pail Kit and Follower Plate 332517B EN For adapting a 60# Dyna-Star Pump for use with a 35# bucket. For professional use only. Part No.: Important Safety Instructions

More information

4-GALLON MOBILE PARTS WASHER

4-GALLON MOBILE PARTS WASHER Please read and save these instructions. Read through this owner s manual carefully before using product. Protect yourself and others by observing all safety information, warnings, and cautions. Failure

More information

3 Scotch Mini-Weld Adhesive System User s Manual

3 Scotch Mini-Weld Adhesive System User s Manual 3 Scotch Mini-Weld Adhesive System User s Manual The Scotch Mini-Weld Adhesive System Includes The items shown below: Contents of User s Manual Ordering Replacement Parts... 1 Important Safety Information...

More information

Operating Instructions for Reka Hot-Melt Glue Applicators

Operating Instructions for Reka Hot-Melt Glue Applicators Operating Instructions for Reka Hot-Melt Glue Applicators TR 700 TR 70 TR 80 TR 60 TR 50.4 TR 55 Table of Contents 1. Product Description 3 2. General Safety Instructions 4 3. Safety Measures to be taken

More information

MAKE CLEANING SAFER NEW TECHNOMELT. Your Machine Cleaning Guide & Hotmelt Cleaner Range

MAKE CLEANING SAFER NEW TECHNOMELT. Your Machine Cleaning Guide & Hotmelt Cleaner Range MAKE CLEANING SAFER NEW TECHNOMELT Your Machine Cleaning Guide & Hotmelt Cleaner Range 2 TECHNOMELT Your Machine Cleaning Guide & Hotmelt Cleaner Range Do you know the advantages of regular and thorough

More information

Automatic Hot Melt Melter/Feeder Retrofit Kit Mechanical Float Model. Part104506A

Automatic Hot Melt Melter/Feeder Retrofit Kit Mechanical Float Model. Part104506A Automatic Hot Melt Melter/Feeder Retrofit Kit Mechanical Float Model Part456A NORDSON CORPORATION. AMHERST, OHIO USA Corporation welcomes requests for information, comments and inquiries about its products.

More information

SuperKlean Washdown Products

SuperKlean Washdown Products February 2012 DURAMIX 8000 INSTALLATION AND MAINTENANCE INSTRUCTIONS **DO NOT THROW AWAY AFTER INSTALLATION** **SAVE AND DISPLAY PROMINENTLY WHERE THIS EQUIPMENT IS USED** WARNING HIGH PRESSURE AND HOT

More information

NORTH AMERICA. Max Max Max Unit. AR F 120V lbs. NOTE or NOTICE: Information that requires special attention.

NORTH AMERICA. Max Max Max Unit. AR F 120V lbs. NOTE or NOTICE: Information that requires special attention. Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information.

More information

Steam Trap BK 45 BK 45-U BK 45-LT BK 46

Steam Trap BK 45 BK 45-U BK 45-LT BK 46 Steam Trap BK 45 BK 45-U BK 45-LT BK 46 Original Installation Instructions 810437-08 Contents Foreword... 3 Availability... 3 Formatting features in the document... 3 Safety... 3 Use for the intended purpose...

More information

Specifications: NORTH AMERICA

Specifications: NORTH AMERICA Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information.

More information

Fiber Optic Module. Part B NORDSON CORPORATION AMHERST, OHIO USA

Fiber Optic Module. Part B NORDSON CORPORATION AMHERST, OHIO USA Fiber Optic Module Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products. Address all correspondence to Nordson Corporation

More information

Single-Point Mini Hydrostatic Sensor for Double-Wall Sumps

Single-Point Mini Hydrostatic Sensor for Double-Wall Sumps Manual No: 577013-838 Revision: B Single-Point Mini Hydrostatic Sensor for Double-Wall Sumps Installation Guide Notice Veeder-Root makes no warranty of any kind with regard to this publication, including,

More information

Product Manual for Pneumatic Reka Glue Guns

Product Manual for Pneumatic Reka Glue Guns Product Manual for Pneumatic Reka Glue Guns www.pakarte.com TR 60 LCD TR 70 LCD Translation from German to English TR 80 LCD TR 55 LCD TR 700 TR 50.4 TR 50.4 25 TR 55 LCD TR 60 LCD TR 700 TR 70 LCD TR

More information

XC-18. NOTE: *Machine shown without Lift-Up Safety Guard. This guard is included with machine. Machine should not be operated without this guard.

XC-18. NOTE: *Machine shown without Lift-Up Safety Guard. This guard is included with machine. Machine should not be operated without this guard. XC-18 NOTE: *Machine shown without Lift-Up Safety Guard. This guard is included with machine. Machine should not be operated without this guard. EXTREMA MACHINERY COMPANY, INC. PO BOX 1450, ALBANY, LOUISIANA

More information

High-Pressure Washer BY02-VBP-WTR BY02-VBP-WTH. CAUTION : Do not use this device before reading the instructions.

High-Pressure Washer BY02-VBP-WTR BY02-VBP-WTH. CAUTION : Do not use this device before reading the instructions. High-Pressure Washer BY02-VBP-WTH BY02-VBP-WTR CAUTION : Do not use this device before reading the instructions. 1 1. Safety Instructions The appliance has been designed solely for private use outdoors

More information

K 2.900M. Operating Instructions. Before first use of the unit read these operating instructions and act in accordance with them

K 2.900M. Operating Instructions. Before first use of the unit read these operating instructions and act in accordance with them K 2.900M Operating Instructions Before first use of the unit read these operating instructions and act in accordance with them. 5.961-933.0 01/07 2 Dear Customer, Please read and comply with these instructions

More information

One Easy Strategy for Savings, Sustainability, and Productivity

One Easy Strategy for Savings, Sustainability, and Productivity One Easy Strategy for Savings, Sustainability, and Productivity How Automatic Adhesive Fill Systems Help in the Quest to Improve Operational Efficiency Nordson Corporation New standards for packaging are

More information

Manual No: Revision: E. Groundwater Sensor. Installation Guide

Manual No: Revision: E. Groundwater Sensor. Installation Guide Manual No: 576013-763 Revision: E Groundwater Sensor Installation Guide Notice Veeder-Root makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranties

More information

AUTOMATIC ICE-CUBE MAKER

AUTOMATIC ICE-CUBE MAKER AUTOMATIC ICE-CUBE MAKER INSTRUCTIONS AND WARNINGS 24478 ed. 11-2007 It is strictly forbidden to reproduce this instruction manual or any part thereof. Dear Customer, Congratulations on having chosen

More information

Fisher Scientific Model 281A Vacuum Oven. Installation and Operating Manual Rev. 0

Fisher Scientific Model 281A Vacuum Oven. Installation and Operating Manual Rev. 0 Fisher Scientific Model 281A Vacuum Oven Installation and Operating Manual 30979 Rev. 0 Preface Models covered in this manual: Catalog numbers Models numbers Voltage 13-262-50 6288 120V 13-262-51 6289

More information

K 2 Basic. Operating Instructions. Please read the operating instructions carefully before using the unit (05/17)

K 2 Basic. Operating Instructions. Please read the operating instructions carefully before using the unit (05/17) K 2 Basic Operating Instructions Please read the operating instructions carefully before using the unit. 59679030 (05/17) Contents Safety instructions............. 3 Description of the Appliance......

More information

Econo-Coat RCM 8000 Powder Spray Booth Installation Guide

Econo-Coat RCM 8000 Powder Spray Booth Installation Guide Installation Guide P/N 1028657A Econo-Coat RCM 8000 Powder Spray Booth Installation Guide WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this

More information

SUPERIOR PERFORMANCE

SUPERIOR PERFORMANCE Economy (E) Series Blast Cabinet Owner s Manual SUPERIOR PERFORMANCE And Quality In Blast Cleaning Equipment! WARNING READ MANUAL Failure to read, understand & follow all safety and operation procedures

More information

BQ-260/260L. Important Information BOOK BINDER

BQ-260/260L. Important Information BOOK BINDER BOOK BINDER BQ-260/260L Important Information - This manual is designed to help you to install, operate and maintain Perfect Binder BQ- 260/260L. Read, understand and keep this manual in a safe and convenient

More information

MAKE CLEANING SAFER NEW TECHNOMELT. Your Machine Cleaning Guide & Hotmelt Cleaner Range

MAKE CLEANING SAFER NEW TECHNOMELT. Your Machine Cleaning Guide & Hotmelt Cleaner Range MAKE CLEANING SAFER NEW TECHNOMELT Your Machine Cleaning Guide & Hotmelt Cleaner Range 2 TECHNOMELT Your Machine Cleaning Guide & Hotmelt Cleaner Range Do you know the advantages of regular and thorough

More information

WALLPAPER STEAMER. Model ASSEMBLY AND OPERATING INSTRUCTIONS

WALLPAPER STEAMER. Model ASSEMBLY AND OPERATING INSTRUCTIONS WALLPAPER STEAMER Model 91098 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright 2004 by Harbor Freight Tools.

More information

Operations and Safety Manual

Operations and Safety Manual Tuffy Jr. Heated Soil Extractor Operations and Safety Manual BEFORE YOU START: SAFETY OPERATION SERVICE PARTS TROUBLESHOOTING RETURN GOODS POLICY! READ and UNDERSTAND this material before operating or

More information

Refrigerant Recovery Machine. Model No Operating Manual

Refrigerant Recovery Machine. Model No Operating Manual Refrigerant Recovery Machine Model No. 25700 Operating Manual Safety Precautions WARNING : TO PREVENT PERSONAL INJURY AND / OR EQUIPMENT DAMAGE, CAUTION - Risk of injury. This equipment should only be

More information

PS-2/ES Automated pack & tag machine with IndES fastening system

PS-2/ES Automated pack & tag machine with IndES fastening system English Manual PS-2/ES Automated pack & tag machine with IndES fastening system Contents 1. Introduction 2. Important Safety Instructions 3. PS-2/ES 4. Unpacking the machine 5. Setting up the machine 6

More information

PORTABLE SMART WASHER

PORTABLE SMART WASHER PORTABLE SMART WASHER User Guide Introduction Thank you for purchasing our Portable Smart Washer, and welcome to the Ivation family. This user manual is meant to offer you a brief walkthrough of the device

More information

Installation and Operating Instructions DÜRR Regeneration Unit for X-ray developers XR 24, XR24 II, XR 24 Nova, XR 24 Pro

Installation and Operating Instructions DÜRR Regeneration Unit for X-ray developers XR 24, XR24 II, XR 24 Nova, XR 24 Pro Installation and Operating Instructions DÜRR Regeneration Unit for X-ray developers XR 24, XR24 II, XR 24 Nova, XR 24 Pro 2006/01 Content Important Information 1. Notes... 3 1.1 CE - Labeling... 3 1.2

More information

SCD. SMALL CYLINDER DRYER with Touchscreen Controller INSTRUCTION MANUAL MANUAL NUMBER Issued March 2015

SCD. SMALL CYLINDER DRYER with Touchscreen Controller INSTRUCTION MANUAL MANUAL NUMBER Issued March 2015 SCD SMALL CYLINDER DRYER with Touchscreen Controller INSTRUCTION MANUAL MANUAL NUMBER 21-11-1042 Issued March 2015 Copyright 2015, Galiso, Inc. 22 Ponderosa Ct., Montrose, CO 81401 (970) 249-0233 (800)

More information

OPERATING AND INSTALLATION MANUAL

OPERATING AND INSTALLATION MANUAL OPERATING AND INSTALLATION MANUAL TANKLESS ELECTRIC WATER HEATER WITH ELECTRO-MECHANICAL FLOW SWITCH» MINI 2» MINI 2.5» MINI 3» MINI 3.5» MINI 4» MINI 6 The Mini series is tested and certified by WQA against

More information

Auto-Flo RT Gun. Customer Product Manual Part A--02. Issued 10/08 NORDSON CORPORATION AMHERST, OHIO USA

Auto-Flo RT Gun. Customer Product Manual Part A--02. Issued 10/08 NORDSON CORPORATION AMHERST, OHIO USA Customer Product Manual Issued 10/08 NORDON CORPORATION AMHERT, OHIO UA afety... 1 Qualified Personnel... 1 Intended Use... 1 Regulations and Approvals... 1 Personal afety... 1 High-Pressure Fluids...

More information

OPERATING MANUAL SPRAY GUN CLEANERS UG UG3000 SERIES UNI-RAM CORPORATION ONTARIO CANADA PATENTS

OPERATING MANUAL SPRAY GUN CLEANERS UG UG3000 SERIES UNI-RAM CORPORATION ONTARIO CANADA PATENTS OPERATING MANUAL SPRAY GUN CLEANERS UG1000 - UG3000 SERIES PATENTS USA 4,788,836 CANADA USA 5,213,117 ENGLAND EUROPE 0300248 ITALY SWEDEN 0300248 GERMANY FRANCE 8110528.0 JAPAN UNI-RAM CORPORATION ONTARIO

More information

Owner s Information Manual

Owner s Information Manual 48ES---A and 48VL---A Comfort and Performance 13 and 14 SEER Single Packaged Air Conditioner and Gas Furnace System With Puron (R---410A) Refrigerant Single and Three Phase 2---5 Nominal Tons (Sizes 24---60)

More information

Fig. 1 - Unit PGD4, PGS4, WPG4

Fig. 1 - Unit PGD4, PGS4, WPG4 OWNER S MANUAL 14 SEER Single -Package Air Conditioner and Gas Furnace System with R -410A Refrigerant Single Phase 2 to 5 Nominal Tons Three Phase 3 to 5 Nominal Tons PGD4andPGS4SeriesE,WPG4SeriesB Fig.

More information

KB Operating Instructions. Before first use of the unit Please read these /07

KB Operating Instructions. Before first use of the unit Please read these /07 KB 6060 Operating Instructions Before first use of the unit Please read these Operating Instructions and act in accordance with them 5.962-095.0 01/07 2 Dear Customer, Please read and comply with these

More information

MODEL A18 SOLVENT RECOVERY SYSTEMS (EXPLOSION PROOF UNITS)

MODEL A18 SOLVENT RECOVERY SYSTEMS (EXPLOSION PROOF UNITS) MODEL A18 SOLVENT RECOVERY SYSTEMS (EXPLOSION PROOF UNITS) FOR PROPER AND SAFE USE OF THIS CHEMCHAMP EQUIPMENT, PLEASE FOLLOW THIS DOCUMENT AND LOCAL AUTHORITY. KEEP THIS DOCUMENT FOR FUTURE REFERENCE.

More information

/2010 US/CA

/2010 US/CA 6 720 646 148-11/2010 US/CA (en) For the user User s Instructions Condensing gas boiler Logamax plus GB162-L.B. 80 kw/100 kw Please read thoroughly before operating This manual is available in the English

More information

Installation and operating instructions. DK energy storage and DK energy buffer

Installation and operating instructions. DK energy storage and DK energy buffer Installation and operating instructions DK energy storage and DK energy buffer Edition: 08-2015 1 Preliminary note With this DK energy storage / DK energy buffer you purchased a DK quality product. The

More information

OPERATING AND INSTALLATION MANUAL

OPERATING AND INSTALLATION MANUAL OPERATING AND INSTALLATION MANUAL TANKLESS ELECTRIC WATER HEATER WITH ELECTRO-MECHANICAL FLOW SWITCH» MINI 2» MINI 2.5» MINI 3» MINI 3.5» MINI 4» MINI 6 The Mini series is tested and certified by WQA against

More information

CONDENSATE PUMP INSTALLATION MANUAL OFFICE PRO 10

CONDENSATE PUMP INSTALLATION MANUAL OFFICE PRO 10 CONDENSATE PUMP INSTALLATION MANUAL OFFICE PRO 10 READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT INSTALLATION AND USAGE, AND READ ALL SAFEGUARDS. 2003 DENSO SALES CALIFORNIA, INC. All rights reserved.

More information

Packaged Heat Pumps. Owner s Guide to Operating and Maintaining Your Heat Pump

Packaged Heat Pumps. Owner s Guide to Operating and Maintaining Your Heat Pump Packaged Heat Pumps Owner s Guide to Operating and Maintaining Your Heat Pump NOTE TO EQUIPMENT OWNER: For your convenience, please record the model and serial numbers of your new equipment in the spaces

More information

Air Filter. Filter for Removing Dust and Drain in Compressed Air. Filter for Drain and Dust (Filtering Accuracy: 5µm)

Air Filter. Filter for Removing Dust and Drain in Compressed Air. Filter for Drain and Dust (Filtering Accuracy: 5µm) http://www.pisco.co.jp AIR PREPARATION ACTUATOR PLARAILCHAIN HARMO ROBOT PARTS Filter for Removing Dust and Drain in Compressed Air Air Filter 220 Filter for Drain and Dust (Filtering Accuracy: 5µm) Resin-made

More information

DC200 Digital Dispenser Operating Manual

DC200 Digital Dispenser Operating Manual DC200 Digital Dispenser Operating Manual 2015 Fisnar Phone: (973) 646-5044 E-mail: info@fisnar.com Table of Contents Product Safety Statements 4 Specifications 6 Accessories 6 External Controls 7 Machine

More information

Integrated Hood Liner

Integrated Hood Liner Integrated Hood Liner Covers models IHL30, IHL36, IHL42, IHL48 and IHL54 Installation Instructions Part No. 65268 Rev. F 2007 Dacor, all rights reserved. Table of Contents Before You Begin... 1 Important

More information

Operating Instructions. PowerFill. Automatic Granulate Conveyor for perfectmelt SE

Operating Instructions. PowerFill. Automatic Granulate Conveyor for perfectmelt SE Operating Instructions PowerFill Automatic Granulate Conveyor for perfectmelt SE - 020100 - 2 Contents Introduction 4 Safety instructions 5 Safety measures with respect to the adhesive 5 Safety measures

More information

Packaged Air Conditioning Units. Owner s Guide to Operating and Maintaining Your Air Conditioner. This manual should be left with the owner.

Packaged Air Conditioning Units. Owner s Guide to Operating and Maintaining Your Air Conditioner. This manual should be left with the owner. Packaged Air Conditioning Units Owner s Guide to Operating and Maintaining Your Air Conditioner ELECTRICAL SHOCK HAZARD. Failure to follow this warning could result in personal injury, Disconnect power

More information