Dynacon Eclipse. Floor Heating Manifolds Floor heating manifold with automatic flow control

Size: px

Start display at page:

Download "Dynacon Eclipse. Floor Heating Manifolds Floor heating manifold with automatic flow control"

Jody Williamson
6 years ago
Views:

1 Dynacon Ecipse Foor Heating Manifods Foor heating manifod with automatic fow contro

IMI HEIMEIER / Foor Heating Contro / Dynacon Ecipse Dynacon Ecipse Dynacon Ecipse adjusts the fow rate in the individua heating circuits directy in /h.

2 IMI HEIMEIER / Foor Heating Contro / Dynacon Ecipse Dynacon Ecipse Dynacon Ecipse adjusts the fow rate in the individua heating circuits directy in /h. This means hydrauic baancing is achieved in one simpe operation. The set fow rate is constanty adapted, i.e. if the rate becomes too high, e.g. due to cosing adjacent circuits, Dynacon Ecipse contros the fow automaticay to the set vaue. The contro cartridge aways ensures a constant fow. This makes Dynacon Ecipse heating circuit manifods a time and cost-saving soution especiay for system commissioning. Key features > > Automatic hydrauic baancing due to integrated fow controer inside each thermostatic insert > > Fow indicator for each heating circuit for functiona check > > Manifod made of stainess stee corrosion-resistant, durabe and safe > > Time and cost-saving commissioning soution Technica description Appication: Foor heating systems Function: Individua room temperature contro with actuator or thermostatic head Fow imitation Shut off Fiing Draining Fushing Venting Pressure cass: PN Fow range: The fow can be stepess pre-set within the range: 0-00 /h. Deivery setting 00 /h. Differentia pressure (ΔpV): Max. differentia pressure: 0 kpa (<0 db(a)) Min. differentia pressure: 0 10 /h = 17 kpa /h = 2 kpa Temperature: Max. working temperature: 70 C Min. working temperature: - C Materia: Manifod: Stainess stee 1.01 Connection fittings: Nicke-pated brass. Thermostatic insert: Brass O-rings: EPDM Vave disc: EPDM Spring: stainess stee Thermostatic insert: Brass, PPS (poyphenysuphide) Spinde: Niro-stee spinde with doube O-ring sea. The outer O-ring is repaceabe under pressure. Fow meter: Heat-resistant pastic and stainess stee. Brass. EPDM seas. Fiing, draining, fushing and venting device: Nicke-pated brass and pastic. EPDM seas. Marking: IMI Heimeier Connection kits: The foowing manifod connection kits are avaiabe: - Connection kit 1 with Gobo ba vaves - Connection kit 2 with STAD baancing vave and Gobo ba vave - Connection kit with Zeparo Vent air separator in suppy pipe and Zeparo Dirt sudge separator in return - Connection kit with Gobo ba vave, incuding spacer for heat meter in return and Gobo ba vave with connection for direct measurement in suppy and return pipe. - Connection kit fixed vaue contro station with high-efficiency pump for controing the suppy temperature. Pipe connection: Manifod with fat-seaing connection, 1 union nut. Heating ciruit connection G / adaptor with Eurcone suitabe for compression fittings for pastic, copper, precision stee and muti-ayer pipe. See aso accessories. Manifod boxes: Manifod boxes avaiabe as surfacemounted and fush-mounted versions. Connection to thermostatic head and actuator: HEIMEIER M0x1. 2

Construction Ecipse thermostatic insert with automatic fow contro 1. Strong return spring in combination with high ocating force ensures that the vave does not sacken off over time 2. HEIMEIER M0x1.

3 Construction Ecipse thermostatic insert with automatic fow contro 1. Strong return spring in combination with high ocating force ensures that the vave does not sacken off over time 2. HEIMEIER M0x1. connection for thermostatic heads and actuators. Automatic fow imiter. Manifod. Long-ife doube O-ring seaing. Fow setting Fow indicator Fiing, draining, fushing and venting device 1. Viewing gass 2. Shut-off handwhee. Manifod. Connection nippe 1. Venting 2. Fiing-, draining and fushing, / connection, swiveing Function Ecipse fow imiter A reguating part is set to the cacuated contro rate by turning the digit cap with the setting key or an 11 mm end wrench. If the fow rate increases at the vave the rising pressure moves the seeve, thus constanty imiting the fow to the set vaue. The set fow rate is therefore never exceeded. If the fow rate drops beow the set vaue a spring presses the seeve back to its origina position.

4 IMI HEIMEIER / Foor Heating Contro / Dynacon Ecipse Appication Dynacon Ecipse adjusts the fow rate in the individua heating circuits directy in /h. This means hydrauic baancing is achieved in one simpe operation. The set fow rate is constanty adapted, i.e. if the rate becomes too high, e.g. due to cosing adjacent circuits, Dynacon Ecipse contros the fow automaticay to the set vaue. The contro cartridge aways ensures a constant fow. This makes Dynacon Ecipse heating circuit manifods a time and cost-saving soution especiay for system commissioning. With conventiona heating circuit manifods with throtte vaves and fow indicators setting the required water quantities is a time-consuming affair. The setting required at the throtte vaves must either be cacuated or set using fow indicators at the manifod. However, the quantities of water distributed in this way ony correspond to maximum requirements. When individua heating circuits are turned off, the quantity of water no onger required is distributed over the adjacent circuits resuting in an oversuppy in these circuits. The automatic hydrauic baance with Dynacon Ecipse avoids this oversuppy in individua heating circuits. This ensures optimum temperature distribution, saves energy and increases comfort. Sampe appication 1. Dynacon Ecipse 2. STAD baancing vave. Gobo P pump ba vave. Room thermostat. Thermostat P with switch cock

5 Operation Fow setting Stepess setting between to 0 (0 to 00 /h). P ace the setting key on the vave insert. T urn the setting too so that desired setting vaue is pointing at the index* of the vave body (see fig.). R emove the key or 11 mm end wrench. The vave is now set. The setting is changed using a specia setting key (artice No ) or an 11 mm end wrench, to ensure tamper proof setting. Front-end and atera visibiity *) 11 mm *) Index Setting /h

6 IMI HEIMEIER / Foor Heating Contro / Dynacon Ecipse Fiing, fushing and venting Product ifetime and system performance strongy depend on proper commissioning. We refer to technica standards EN 1, VDI20 and ON H19-1 to be carefuy attended. Each heating circuit must be individuay fied, fushed and vented: Cose the ba/shut-off vaves (1). Cose a thermostatic inserts with the protection caps (). A fow controers (2) or fow meters () must be competey open! Connect the fi- and drain hose and open the fiing, draining, fushing and venting device (). Fi/Fush the circuits each by each. Open the thermostatic insert of the 1. heating circuit with the protection cap () competey. After fushing the 1. circuit cose the corresponding thermostatic insert and fi/fush the next circuit. Setting of the fow controer or fow meter: See Instaation and operating instruction. Pressure test Pressure test duration before and during screed aying. The test pressure is 1. times of the permissibe operating pressure. Therma fuid To stop any damage and scae in hot water heating systems, the composition of the therma fuid is to conform to VDI Directive 20. For industria and ongdistance energy systems, see appicabe codes VdTÜV and 1/AGFW FW 10. Minera oi in the therma fuid and/or a kinds of ubricants containing minera oi ead to considerabe sweing and, in most cases, to the faiure of EPDM seas. When using nitrite-free antifreeze and anti-corrosive based on ethyene gyco, technica advice especiay on additive concentration is to be taken from the anti-freeze/anti-corrosive manufacturer s documentation. Functiona heating Carry out functiona heating of heating screed conforming to standards in keeping with EN -. 1 mm Eariest start for functiona heating: Cement screed: 21 days after aying Anhydrite screed 7 days after aying Begin 20 C - 2 C fow temperature and maintain for days. Then set maximum design temperature and maintain for days. Fow temperature can be reguated by controing the heat generator. Refer to the screed manufacturer s information! 1 \ 2 mm Do not exceed maximum foor temperature at the heating pipes: Cement and anhydrite screed: C Poured asphat screed: C according to screed manufacturer s technica advice!

7 Technica data Fow rate range per heating circuit: 0-00 /h 2 db(a) max. Δp min /h = 17 kpa Δp min /h = 2 kpa Δp max. 0 kpa Sampe cacuation Target: Set vaue of Dynacon Ecipse fow controer /h kpa min. Given: Heat fow, heating circuit Q = 10 W Temperature spread Δt = 8 K (/ C) Soution: Mass fow m = Q / (c Δt) = 10 / (1.1 8) = 0 kg/h Lowest fow toerances Fow reguator setting at Dynacon Ecipse manifod: = /h 0-10 /h: 17 kpa /h: 2 kpa Setting vaues with different heating performances and system differentia temperatures p min /h = 17 kpa p min /h = 2 kpa Q = Heating performance Δt = System differentia temperature Δp = Differentia pressure Sampe: Q = 1000 W, Δt = 1 K Setting vaue: ( 0 /h) 7

8 IMI HEIMEIER / Foor Heating Contro / Dynacon Ecipse Artices Dynacon Ecipse underfoor heating circuit manifod Heating circuits Artice No Connection kit 1 with Gobo ba vaves, DN 20 with red end cap in suppy and bue end cap in return. Kvs Artice No 9, Connection kit 2 with STAD baancing vave and Gobo ba vave, DN 20 incuding measuring nippe for measuring differentia pressure and fow rate. Kvs q max Artice No [m /h],28 2, Connection kit with Zeparo Vent air separator in suppy and Zeparo Dirt sudge separator in return, DN 20 Kvs q max Artice No [m /h],72 1, S-connection For connection kit. Instaation aid for return in manifod boxes. Artice No Kvs = m /h at a pressure drop of 1 bar and fuy open vave.

9 Connection kit with Gobo ba vave DN 20, incuding spacer for heat meter in return Gobo ba vave with connection G1/ for direct measurement in suppy and return. Kvs Artice No 9, Connection kit, fixed vaue contro station with high-efficiency pump Grundfos Apha , thermostatic vave with contact sensor and eectrica pipe contact safety switch 20V, 1A. Minimum instaation depth manifod boxes: mm. Setting range thermostatic head Setting range eectrica pipe-contact sensor Artice No 20-0 C C Manifod boxes Fush-mounted box, instaation depth mm Note the minimum instaation depth mm for connection set! Size B x H Artice No 1 90 x 710 mm x 710 mm x 710 mm x 710 mm x 710 mm x 710 mm Manifod boxes Surface-mounted box, instaation depth mm Size B x H Artice No 1 9 x 20 mm x 20 mm x 20 mm x 20 mm x 20 mm x 20 mm Kvs = m /h at a pressure drop of 1 bar and fuy open vave. 9

10 IMI HEIMEIER / Foor Heating Contro / Dynacon Ecipse Accessories EMOtec Two-point therma actuator for foor heating systems. With position indicator in NC version. Suitabe for a IMI Heimeier thermostatic vave bodies. For technica data, pease refer to the EMOtec datasheet. Type Artice No 20 V Currentess cosed (NC) Currentess open (NO) V Currentess cosed (NC) Currentess open (NO) Room thermostat with therma recircuation, contros the room temperature in connection with therma actuators. Mode Artice No 20 V Without temperature set-back With temperature set-back V Without temperature set-back C Thermostat P with anaog switch cock eectronic two-point room thermostat for time-dependent contro of the room temperature, with anaog 7-day automatic timer, puse-width moduation output signa (PWM) and foating change-over contact. Mode Artice No 20 V Thermostat P with digita switch cock eectronic two-point room thermostat for time-dependent contro of the room temperature, with digita automatic timer, puse-width moduation output signa (PWM) and foating change-over contact. Menu-driven via four buttons. Mode Artice No 20 V Distributor strip This unit is used for wiring thermostats and eectro-therma actuators. The unit is suitabe for underfoor heating and cooing (summer/winter operation). It is possibe to switch over between heating and cooing via an externa signa. The pump ogic enabes enery-optimised pump contro. For up to zones (rooms). Ready to pug in to a 20 V power socket. Artice No

11 Radiocontro F Radio contro system for individua room temperature contro of foor, wa or cei heating and cooing in connection with therma two-point actuators (e.g. EMO T / EMOtec ). Room transmitter battery-driven eectronic Fuzzy controer, incuding battery. Type Artice No with digita timer, inc. battery without operating mode switch, inc. battery with operating mode switch, inc. battery Centra unit Receives the room transmitters radio signas. With 8 or output channes for the connection of the therma actuators. Mode Centra unit Artice No output channes without time cock 8 output channes with time cock Thermostatic head F Remote dia with buit-in sensor. Liquid fied sensor. Setting range 0 C to 27 C. Capiary tube ength [m] Artice No 2, , , , Handwhee for a HEIMEIER thermostatic vave bodies. With direct connection, white. Artice No Length adjustment fitting For camping pastic, copper, precision stee or muti-ayer pipes. For vaves with mae thread connection G /. Brass nicke-pated. L Artice No G/ x G/ G/ x G/ Compression fitting for pastic pipe according to DIN 72, ISO PE-X: DIN 1892/189, EN ISO 187; PB: DIN 198/199. Connection mae thread G / according to DIN EN 11 (Eurocone). Nicke pated brass. Ø Pipe Artice No 1x x x x x

12 IMI HEIMEIER / Foor Heating Contro / Dynacon Ecipse Compression fitting for copper or precision stee pipe according to DIN EN 107/100-1/2. Connection mae thread G / according to DIN EN 11 (Eurocone). Meta-to-meta joint. Brass nicke-pated. With a pipe wa thickness of mm insert supporting seeves. Heed pipe manufacturer s technica advice. Support seeve for copper or precision stee pipe with a 1 mm wa thickness. Brass. Ø Pipe Artice No Ø Pipe L Artice No 2, , , , Compression fitting for copper or precision stee pipe according to DIN EN 107/100-1/2. Connection mae thread G / according to DIN EN 11 (Eurocone). Soft seaed, max. 9 C. Nicke-pated brass. Ø Pipe Artice No Compression fitting ffor Au/PEX muti-ayer pipe according to DIN 18. Connection mae thread G / according to DIN EN 11 (Eurocone). Nicke-pated brass. Ø Pipe Artice No 1x Doube connection fitting For camping pastic, copper, precision stee or muti-ayer pipes. Brass, nicke-pated. Doube nippe Both sides for camping pastic, copper, precision stee or muti-ayer pipes. Brass nicke-pated. L Artice No G/ x R1/ Artice No G/ x G/ Repacement thermostatic insert with automatic fow imiter for Dynacon Ecipse. Artike-Nr Dynacon Ecipse fow indicator Spare insert. Artike-Nr

13 Repacement fiing, draining, fushing and venting device 1/2 for Dynacon Ecipse and Dynatec Ecipse. Artice No 1/

14 IMI HEIMEIER / Foor Heating Contro / Dynacon Ecipse Dimensions - manifod and connection kits 20**) A 90**) C B **) **) E D 0 0**) **) G F 90 0**) 80 Heating circuit manifod, heating circuits A B C D E F G Length [mm] Length, incuding kit mm bend * Box size Length, incuding kit mm bend * Box size Length, incuding kit 1 and kit + 0 mm bend * Box size Length, incuding kit 2 and kit + 0 mm bend * Box size Length, incuding kit + 0 mm bend * Box size Length, incuding kit Fixed vaue contro station Box size *) Suppied without bend 1 2 **)

15 Dimensions - manifod boxes 99-90/ / B B H H Size W x H [mm] Surface-mounted box, instaation depth mm 1 9 x x x x x x 20 Fush-mounted box, instaation depth mm 1 90 x x x x x x 710 Note the minimum instaation depth mm for connection set! 1

16 IMI HEIMEIER / Foor Heating Contro / Dynacon Ecipse The products, texts, photographs, graphics and diagrams in this document may be subject to ateration by IMI Hydronic Engineering without prior notice or reasons being given. For the most up to date information about our products and specifications, pease visit Dynacon Ecipse EN

Dynalux. Floor Heating Manifolds Underfl oor heating circuit manifold

Dynalux. Floor Heating Manifolds Underfl oor heating circuit manifold Dynalux Floor Heating Manifolds Underfl oor heating circuit manifold IMI HEIMEIER / Floor Heating Control / Dynalux Dynalux Dynalux adjusts the flow rate in the individual heating circuits directly in