Installation Instructions

Transcription

1 Salvajor S914 Scrap Collector A Scrapping, Pre-flushing and Food Waste Collecting System 2 Table Installation and Location 3 Plumbing 4 Electrical 5 Operating Instructions 6 Typical Installations 8 Warranty ALL INSTALLATIONS SHOULD BE MADE IN ACCORDANCE WITH LOCAL AND NATIONAL PLUMBING AND ELECTRICAL CODES. Installation Instructions The Salvajor Company 4530 East 75th Terrace Kansas City, Missouri , USA SALVAJOR FAX: sales@salvajor.com service@salvajor.com Manufacturers of Commercial Food Waste Disposing Systems since 1944

2 Table Installation and Location The S914 Scrap Collector is designed for installation into a soiled dishtable. Locate the unit at least 24 away from the loading end of the dishmachine to allow sufficient space for dish racks. ARROWS INDICATE DISH FLOW The Scrap Collector is furnished with a template for making the proper cut-out in the dishtable for installation. Once the location of the Collector has been determined, place the template in position on the tabletop and mark the opening to be cut. Make certain that the gusher tube inside the Collector is positioned on the side closest to the dish machine or sink. The flow of the water plume from the gusher tube must angle up and away from the dishmachine or sink. The unit is now ready for installation /32" (48.35) 15" (38.10) 20" ( 50.80) TABLE CUTOUT GUSHER TUBE Collectors are most commonly welded to the dishtable. However, they are furnished with the mounting flanges punched for either bolting or studweld bolting to the table. 2

3 Plumbing 1. WATER SUPPLY The Salvajor Scrap Collector is designed for easy plumbing installation. The solenoid valves are factory installed and are attached to an automatic water blender which will introduce water tempered to approximately 107 F. Plumb 3/4" lines from both hot and cold water supply sources and reduce to 1/2" before attaching to corresponding valves on the Collector water harness. SOLENOID WATER BLENDER CHECK VALVES 1 /2" BALL VALVES INCOMING WATER 2" NPT DRAIN IMPORTANT: The Scrap Collector is equipped with an approved air gap, eliminating the need for vacuum breakers. 2. DRAIN PIPING Plumb a 2" pipe from the 2" male threaded nipple located on the bottom of the Collector reservoir tank to the nearest approved drain. The drain line should have a minimum of 1/4" NOTE: To assure against leaks, tighten water harness fittings. They may come loose during shipment, fabrication or installation. Pressure regulators should be installed in areas where water pressure exceeds the recommended maximum of 80 psi. slope of fall per running foot. It is the responsibility of the plumbing contractor to check all connections to ensure they are free of leaks. MAKE ALL PLUMBING CONNECTIONS IN ACCORDANCE WITH NATIONAL AND LOCAL PLUMBING CODES. 3

4 Electrical ELECTRICAL The wiring diagram for electrical connections is located in the terminal strip box mounted on the side of the Collector above the motor. A secondary diagram is located within the control panel furnished with the unit. The motor and solenoid valve furnished with the unit are factory prewired to the terminal strip box. Field wiring will consist of wiring from the terminal strip box to the control panel as shown on the wiring diagram and wiring from the power source to the control panel. The Scrap Collector is supplied with a Salvajor Model SS-33 control panel which will control the Collector motor and solenoid valve. The motor is protected by automatic internal overloads. The enclosure for the Model SS-33 control is stainless steel, NEMA 4X watertight rated and UL listed. OUT TO SYSTEM 1 /2" CONDUIT IN FROM CONTROL PANEL 1 /2" CONDUIT INCOMING POWER 1 /2" CONDUIT TOTAL FULL LOAD AMPS PHASE 115V 208V 230V V 1PH PH NOTE: Always use watertight conduit and fittings when wiring this product. MAKE ALL INSTALLATIONS IN ACCORDANCE WITH LOCAL AND NATIONAL ELECTRICAL CODES. STOP! If you have any questions about this installation call SALVAJOR for installation advice. 4

5 Operating Instructions TO START: 1 Place OVERFLOW PIPE into drain opening in bottom of tank (center hole). 2 Position SCRAP BASKET inside tank. 3 Position SALVAGE BASIN inside tank over SCRAP BASKET. 4 Press START button on CONTROL PANEL. Allow time for reservoir tank to fill and the water plume to remain at a constant height. 5 Adjust WATER PLUME VALVE. Recommended plume height 4-6. TO STOP: A Press STOP button on the CONTROL PANEL. B Check for and remove dropped tableware trapped in SALVAGE BASIN. C Remove and drain SALVAGE BASIN. D Remove SCRAP BASKET and dump waste into trash receptacle. E Remove OVERFLOW PIPE to drain tank. Rinse SALVAGE BASIN, SCRAP BASKET, OVERFLOW PIPE, and tank interior thoroughly. 5

6 Typical Installations FIELD CONNECTIONS INCOMING POWER 3/4 HOT AND COLD WATER REDUCED TO 1/2 AT WATER HARNESS CONNECTION 2 DRAIN JUNCTION BOX POWER CONNECTION PASS THRU WINDOW 6

7 Typical Installations ACCUMULATOR 7

8 Salvajor Warranty ONE YEAR PARTS AND LABOR Equipment covered by this warranty: All Salvajor commercial disposers and disposing systems. Length of this warranty: Parts and labor for one year from date of installation or 15 months from date of shipment from the factory, whichever occurs first. Accessories are covered when they are sold as part of the original disposer assembly or system package. Warranty coverage: Providing the equipment is unaltered, has been properly installed, maintained and operated, Salvajor will repair or replace at no cost, defective parts due to material or workmanship, if such service is performed by a Salvajor Authorized Service Center. Parts wear is not considered a defect. Conditions not covered by this warranty: Faulty or improper electrical installations, faulty or improper plumbing installations, disposer jammed by foreign object, tripped overload (re-set button), clogged drains, pump jams, clogged solenoid valves, abuse, accidental damage, unit improperly sized for application according to factory recommendations. This warranty is limited to the continental United States, Hawaii and Canada. For your nearest Factory Authorized Service Center: Call SALVAJOR or Fax or The Salvajor Company 4530 East 75th Terrace Kansas City, Missouri , USA SALVAJOR (816) FAX: sales@salvajor.com service@salvajor.com Manufacturers of Commercial Food Waste Disposing Systems since Printed in USA Form No. II-S914-1