REFLECTOR PANS FOR HINGED ELEMENTS CONNECTOR BLOCK KIT TRIM RINGS FOR ABOVE PANS CONNECTOR BLOCK RANGE CORD REFLECTOR PANS FOR PLUG-IN ELEMENTS

Transcription

1 *s are Subject to Change without Notice.* REFLECTOR PANS FOR HINGED ELEMENTS Heavy Chromed Steel Description " UNIVERSAL $ " UNIVERSAL $ " GE/HOTPOINT $ " GE/HOTPOINT $2.98 TRIM RINGS FOR ABOVE PANS Heavy Chromed Steel Description " UNIVERSAL $ " UNIVERSAL $ " GE/HOTPOINT $ " GE/HOTPOINT $2.49 REFLECTOR PANS FOR PLUG-IN ELEMENTS Heavy Chromed Steel Description " $ " $3.39 SINGLE COIL PLUG-IN RANGE ELEMENTS Description ", 1250 WATTS $ ", 2100 WATTS $15.98 Connector Block Kit CONNECTOR BLOCK KIT Connector block kit for plugin surface elements. Comes with two different mounting brackets, two 6 long electrical wires with connector terminals and one black plugin block that fits both brackets $8.98 CONNECTOR BLOCK This connector block comes with screw terminals for connecting electrical wire leads. For use with plug-in type surface units. Description SCREW TERMINALS $7.98 RANGE CORD 3-Wire Flat Prongs 50 AMP 4 Ft. Long 2 #6, 1 #8 wires $11.98 RANGE CORD 4-Wire 50 AMP 4 ft. long 2 #6, 2 #8 wires $19.95 CONTROLS FOR SURFACE UNITS (Infinite Switch) Kit is complete with mounting screws, instructions, and adapter for using original knobs. 240 volts ac. Description PUSH TO TURN $ TURN WITH PUSHING IN ON KNOB $18.95 Page 59

2 *s are Subject to Change without Notice.* RANGE RECEPTACLE 3-Wire 50 AMP DRYER RECEPTACLE 4-Wire 30 AMP Grounding Type $6.95 RANGE RECEPTACLE 4-Wire 50 AMP Grounding Type $7.98 WASHING MACHINE FILL HOSES For hot and/or cold water. made of reinforced rubber. 5 ft. long $7.98 DRYER CORD 3-Wire Flat Prongs 30 AMP 4 Ft. Long 3 #10 Wires $8.49 DRYER CORD 4-Wire 30 AMP 4 Ft. Long 4 #10 Wires $11.98 DRYER RECEPTACLE 3-Wire 30 AMP Non-Grounding. Description HAS STRAIGHT ENDS $ HAS 90 DEGREE ELBOW ON ONE END $7.98 WASHING MACHINE FILL HOSE No-Burst Stainless steel braided, 300 lb. working 125 deg. F., 500 lb. working 72 deg. F. Description FT. LONG $7.98 WASHING MACHINE DRAIN HOSE 5 ft. long Description HAS HOOK ON ONE END $6.98 GE / HOTPOINT DRAIN HOSE No kink elbows and hooks stay where you put them $6.45 Description " LONG $ " EXTENSION FOR GE / HOTPOINT DRAIN HOSE $12.29 Page 60

3 *s are Subject to Change without Notice.* MOUNTING BLOCK J-Channel Outside Light Fixture DRYER VENT HOSE 4" Dia. 5-Ply Multi-Layered Flexible Metallic Duct UL Listed 181 Class 1 Description FT. LONG, (2-plastic clamps included) $ FT. LONG $21.29 DRYER VENT DUCT 4" Dia. Semi-Rigid Flexible Aluminum Duct Sold in 8 ft. lengths only $6.49 VENT HOOD & PIPE 4" Dia. x 11" Long aluminum pipe with a white, non-corrosive, high-impact hood with damper and a removable bird/pest guard. Has a white plastic finishing collar for inside wall $4.98 VENT HOOD & PIPE 4" Dia. x 11" long aluminum pipe and a white 6" x 6" x 5/8" highimpact, non-corrosive louvered hood. Louvers open with discharge air pressure from dryer. Has a white plastic finishing collar for inside wall $5.69 This is a 2-piece unit, inside piece mounts to the wall, then the 7 x 7 outside piece snaps into the inside piece with two stops, one at 3/4 depth and the other at 1-1/4 depth. The outside piece has a 4 diameter hole in which to access and fasten the electrical wiring and fixture mounting devices. Made of heavy PVC. White $6.39 MOUNTING BLOCK J-Channel Duplex Receptacle This 2-piece J-channel mounting block is designed to install a duplex receptacle where horizontal vinyl siding is being installed. The inside piece mounts to the wall and the 4-1/2 x 6-5/16" outside piece snaps into the inside piece with two locking positions. One locking position at 1/2" depth and the other at 13/16" depth. May be installed vertical or horizontal. Made of PVC. White $6.79 MOUNTING BLOCK J-Channel Sillcock This split 2-piece J-channel mounting block is designed to use when installing horizontal siding on a structure that has a sillcock installed. The inside piece mounts onto the wall. The 5" wide x 6-3/4" high outside piece snaps into the inside piece with three stops; one at 3/4" depth, one at 1" depth and the third at 1-1/4" depth. Each piece is split into so that it easily fits around the sillcock. Made of PVC. White $7.98 Page 61

4 *s are Subject to Change without Notice.* VENT ASSEMBLY Horizontal Siding This vent assembly comes with a plate that mounts to the wall before installing horizontal siding. The vent hood attaches to the wall plate creating a pleasing finished look. Made of hi-impact noncorrosive white plastic. 4" dia. by 11" long aluminum pipe $14.98 HORIZONTAL RANGE HOOD VENT with J-Channel Ventline Brand Made of UV stabilized polystyrene extruded plastic. Has lockable damper. Throat of damper assembly is 1-5/8 long and fits opening of 3-1/2 x 10-1/2. Overall outside dimensions of the two-piece j-channel assembly is 14-1/4 long x 7-3/8 high. J- channel has depth stops at 5/8 and 7/8 to accommodate different horizontal siding thickness. We stock white only $19.89 CLAMPS FOR DRYER HOSE Description " METAL $0.69 UNDEREVE HOOK-UP KIT This venting kit comes with enough four inch diameter semi-rigid aluminum flexible duct to get you out of the eve area and into the attic space. The under eve vent prevents birds & animals from entering venting system $19.05 COUPLER DRYER DUCT Connects any flexible and/or semi-rigid duct together. No clamps, tools or tapes needed. Made of hi-impact plastic. For 4" dia. duct $2.39 ELBOW ADJUSTABLE This 4" diameter, 90 degree light weight aluminum elbow is made to accommodate flexible, semi-rigid or rigid dryer venting duct or bathroom venting duct. Crimped on one end only $3.98 PIPE ALUMINUM Made of lightweight aluminum for use as dryer or bathroom venting. Crimped on one end only. Description " DIA. x 24" LONG $2.55 PROTECTOR FOR DRYER HOSE Prevents crushing hose between wall and dryer. Just screw protector onto dryer hose, put gasket onto dryer connection, then slip protector onto dryer connection. 5-3/4" overall length. White high-impact plastic. For 4" diameter hose $4.45 Page 62

5 *s are Subject to Change without Notice.* DRYER VENTING BOX This white recessed in-wall plastic dryer box allows dryer to sit 4" to 6 closer to wall. Can improve dryer efficiency and can reduce fire hazard. Open top for metal pipe pass-through $23.59 DEPRESSURIZATION VENT SYSTEM For walls from 3-5/8" to 8" thick. Fits a 4-1/4" Dia. hole. White plastic interior/ exterior louvered plates. Has bug screen inside and outside. Has a damper inside of interior grill which allows for expulsion of inside air without allowing back drafts of outside air. Comes with mounting screws $16.98 DEPRESSURIZATION VENT SYSTEM IN WALL DRYER VENTING SYSTEM This aluminum venting system fits in-wall installations up to 9 tall. Comes with one 4" oval to 4" round top boot, one 4" oval to 4" round 90 degree boot and three 32" long x 4" oval pipe and support strap $28.45 TIGHT SPACE DRYER HOOK-UP KIT Four inch oval aluminum duct allows dryer installation three inches from rear wall. Telescopes from 18" to 31". May be positioned vertical, horizontal, or diagonal $20.09 For walls from 4-3/8 to 6 thick, fits a 4-1/4 diameter opening. Made of molded almond colored plastic. Rounded louvered mounting plate is 5-1/2 in diameter. Louvered spacing is small enough to prevent most insects from entering. Has a damper which allows for expulsion of inside air without allowing back drafts of outside air $9.98 EXTENSION GALVANIZED STEEL This extension connects from range hood horizontally through wall to horizontal outside vent. Description /16" W. x 3-1/8" H. x 6" L $2.69 GALVANIZED TRANSITION This 3-1/4" x 10" galvanized transition converts a rectangular top discharge range hood to a round discharge. Description " DIA. ROUND $ " DIA. ROUND $7.13 Page 63

6 *s are Subject to Change without Notice.* BROAN RANGE HOODS Vent-free Broan Brand These vent-free units have a Microteck System filter that is nine times more efficient than vent-free filters of other manufacturers. 120 volt two-speed fan system. Has rocker type fan & light switches. Uses one 75 watt light bulb (not included). One-year limited product warranty. Description " WIDE, WHITE $ " WIDE, ALMOND $ " WIDE, STAINLESS STEEL $ RANGE HOODS Vertical/Horizontal Discharge Broan Brand 120 volt two-speed motor discharges up to 160 cfm of air through 3-1/4" x 10" opening in back or top of unit. Noise level is a quiet 5.5 sones. Rocker type fan & light switches. Dishwasher safe aluminum grease filter. Uses one 75 watt light bulb (not included). One-year limited product warranty. Description " WIDE, WHITE $ " WIDE, ALMOND $ " WIDE, STERLING* $ " WIDE, STAINLESS STEEL $ " WIDE, BLACK $ " WIDE, WHITE $ " WIDE, ALMOND $ " WIDE, STERLING* $ " WIDE, BLACK $98.00 RANGE HOODS Vertical Discharge Broan Brand 120 volt two-speed fan system discharges up to 190 cfm of air through a 7" diameter round duct on top of unit. Has dishwasher safe aluminum grease filter. Noise level is a quiet 5.5 sones. Rocker type fan & light switches. Uses one 75 watt light bulb (not included). One-year limited product warranty. Description " WIDE, WHITE $ " WIDE, ALMOND $ " WIDE, WHITE $ " WIDE, ALMOND $74.95 * All Sterling Finish Range Hoods are by Ventline Brand. Light, No Fan 42 RANGE HOODS, LIGHT, NO FAN, by VENTLINE WHILE QUANTITIES LAST. Description " WIDE, ALMOND $ " WIDE, STERLING* $45.00 * All Sterling Finish Range Hoods are by Ventline Brand. Page 64

7 *s are Subject to Change without Notice.* VENTLINE Replacement Motor & Blade RANGE HOODS Vertical Discharge Ventline Brand PR Series 120 volt two-speed motor discharges 50 cfm of air on low speed and 100 cfm of air on high speed vertically thru a 5"diameter round opening. Has dishwasher safe aluminum grease filter. Rocker type fan & light switches. Uses one 40 watt light bulb (not included). One-year limited product warranty. Description " WIDE, WHITE $ " WIDE, ALMOND $ " WIDE, BLACK $ " WIDE, WHITE $ " WIDE, ALMOND $ " WIDE, BLACK $ REPLACEMENT MOTOR & BLADE FOR BROAN & NUTONE BATH FANS This replacement motor fits Broan and Nutone s 50 cfm bathroom ventilator fans. The 120 volt motor pulls only.90 amps and has a noise rating of only 2.0 sones. Motor has a male plug on one end of 6 long electrical wires. The 5/32 diameter motor shaft is 1-5/8 long with a splined (serrated) end. The 4-12 diameter plastic fan blade comes standard with the motor $32.95 REPLACEMENT LENS Description /16" x 9-1/2" FLAT, NO LIP $ /8" x 9-7/16" HAS LIP ON ONE SIDE $7.39 GREASE FILTERS Washable Aluminum Range Hoods Description /4" x 11-1/4" x 3/8" (Nutone, Ventrica $7.98 & Kitch-n-Vent /2" x 9-1/2" x 3/8" $ /2" x 9-1/2" x 5/16" $ /2" x 8-3/4" x 3/32" (Broan) $ /4" x 10-1/2" x 3/8" (Broan), (Polysorb $11.98 Activated Carbon Filter) " x 7-3/4" x 3/32" $ " x 8" x 3/32" (Ventline) $ /8"x 11-3/4" x 3/8", (2-5/8" x 10-3/8" $15.98 light lens runs across the entire 11-3/4" width of the filter.) /8" x 9-3/4" x 3/32" $9.98 REPLACEMENT MOTOR & BLADE For BROAN & NUTONE RANGE HOODS 2-Speed Motor This replacement motor and fan blade fits Broan and Nutone s range hoods with air flow ratings of up to 190 CFM (cubic feet per minute). Three-wire two speed motor pulls 1.1 amp on 120 volt ac. The five-blade 6-1/2 diameter plastic fan blade turns clockwise looking into shaft of motor. The electrical leads have a three-pin molded plug on one end $37.95 Description REPLACEMENT SPRING CLIP (Not Shown), (Secures filter & lens to Ventline range hoods) $3.69 Page 65

8 *s are Subject to Change without Notice.* Range Hoods, Bathroom Fans, Sidewall Fans REPLACEMENT MOTORS Range Hoods, Bathroom Fans Sidewall Fans Direction of rotation can be changed by placing shaft on opposite side of motor assembly. Requires removing two screws reversing the shaft and replacing the two screws, comes with electrical leads. Some motors have plugs on electrical wires. 120 volt ac. Description SINGLE SPEED, 1.45 AMP, $ RPM SINGLE SPEED,.77 AMP, $ RPM SINGLE SPEED,.96 AMP, 3000 RPM $ TWO SPEED, 1.15 AMPS, $ RPM REPLACEMENT FAN BLADES For range hoods, sidewall ventilators and bathroom fans. Description BLADE, PLASTIC, 6-1/2" DIA. fits $7.19 7/32"dia. shaft, clockwise rotation BLADE, PLASTIC, 5-3/4" DIA. fits $7.19 7/32" dia. shaft, clockwise rotation BLADE, PLASTIC, 6-5/8" DIA. fits $7.19 7/32" dia. shaft, counter clockwise rotation BLADE, PLASTIC, 6-7/8" DIA. fits $7.29 7/32" dia. shaft, counter clockwise rotation BLADE, PLASTIC, 6-5/8" DIA. fits 7/32" dia. shaft, clockwise rotation, 22 degree blade pitch (Broan and Nutone Range Hoods) $5.98 Exhaust Fan BLOWER WHEEL EXHAUST FAN This plastic blower wheel is designed for quiet operation with low maintenance and high reliability. Wheel is 5-3/4" in diameter x 2" wide, clockwise rotation and fits 1/4" diameter motor shaft. Rotation is determined by looking at end of motor shaft $11.98 FAN BLADE Bathroom Ceiling Fans Fan blade is 4-9/16" diameter x 1-1/16" thick, counter clockwise rotation looking into the vanes. Fits 7/32" diameter motor shaft. Black plastic. Fits our fan number $4.75 LIGHT LENS Range Hood This milk white plastic replacement light lens fits Broan 40000, and series range hoods as well as some Nautilus, Sears and WCI range hoods $5.98 PIGTAIL HARNESS This 2-wire pigtail harness is 6" long with a male plastic plug with female electrical contacts. Fits Motor $3.15 HORIZONTAL OUTSIDE VENTS Made of UV stabilized heavy polystyrene plastic with lockable damper, 3-1/2" x 10-1/2" rough opening. Weatherproof design. Description WHITE $ ALMOND $6.79 HORIZONTAL RANGE HOOD VENT with J-Channel Ventline Brand Made of UV stabilized polystyrene extruded plastic. Has lockable damper. Throat of damper assembly is 1-5/8 long and fits opening of 3-1/2 x 10-1/2. Overall outside dimensions of the two-piece j-channel assembly is 14-1/4 long x 7-3/8 high. J- channel has depth stops at 5/8 and 7/8 to accommodate different horizontal siding thickness. We stock white only $19.89 Page 66

9 *s are Subject to Change without Notice.* ROTARY SWITCH RANGE HOODS Two wire snap-in rotary button switch for use in some Ventline brand range hoods. 12" long wire leads. Black $6.29 REPLACEMENT SWITCHES Fan & Light Description ROTARY SWITCH (4-position, 3-speed) $ KNOB (for 4-position rotary switch #2-2089, (Black Plastic) $4.89 LIGHT SWITCH Range Hoods Single pole rocker type snap-in light switch, body is made of plastic with light icon. Switch is 1.24 (1-1/4 ) long x.68 (11/16 ) wide, (measurements taken at outer edge of switch bezel). Has.25 (1/4 ) wide male slip-on spade type electrical terminals. Black only. Description BLACK $8.39 FAN SWITCHES Range Hoods Rocker type snap-in switch with plastic body and fan icon with low-speed & high-speed indicator. Switches are 1.24 (1-1/4 ) long x.68 (11-16 ) wide, (measurements taken at outer edge of switch bezel). Has.25 (1/4 ) wide male slip-on spade type electrical terminals. Description SINGLE SPEED, BLACK $ TWO SPEED, BLACK $ W TWO SPEED, WHITE $8.39 LIGHT SWITCH Range Hoods Rocker type single pole snap-in switch with plastic body. Switches are.85 (13/16 ) long x.594 (19/32 ) wide, (measurements taken at outer edge of switch bezel). Has.187 (3/16 ) wide male slip-on spade type electrical terminals. Black with white light icon. Description BLACK $7.98 FAN SWITCHES Range Hoods Rocker type single pole (one speed) and single pole double throw (two speed) snap-in switches with plastic body. Switches are.85 (13/16 ) long x.594 (19/32 ) wide, (measurements taken at outer edge of switch bezel). Has.187 (3/16 ) wide male slip-on spade type electrical terminals. Black with white fan icon. Description SINGLE SPEED $ TWO SPEED $7.98 LAMP SOCKET 2-wire, 120 volt ac light bulb socket for range hoods. Has spring steel snap-in type fastener $3.39 SIDE WALL VENT (115 VOLT AC) ROUGH OPENING: 9-1/4" x 9-1/4" GRILL SIZE: 11-1/8" x 11-1/8" Description /4" to 4" WALL THICKNESS $55.00 Page 67

10 *s are Subject to Change without Notice.* REPLACEMENT MOTOR This single speed volt motor runs at 3250 rpm, pulls.77 amp and can be made to run either direction by removing two bolts and placing shaft on opposite side of motor. Comes with 15" electrical leads. Description SINGLE SPEED, (also fits some range $19.95 hoods) REPLACEMENT FAN BLADE 3-BLADE PLASTIC, 6-1/2" DIA. fits 7/32" dia. shaft, clockwise rotation looking at shaft end of motor $7.19 Description REPLACEMENT SPIRAL SPRING, (For $1.79 use on chain) Description REPLACEMENT INSIDE GRILL, WHITE $ REPLACEMENT INSIDE GRILL, STERLING $9.98 Description REPLACEMENT OUTSIDE COVER, $9.89 WHITE I REPLACEMENT OUTSIDE COVER, IVORY $9.89 Description REPLACEMENT PULL CHAIN, 18" $7.29 LONG Description REPLACEMENT SPRING, (FLAT) FOR $1.89 OUTSIDE DOOR Description REPLACEMENT RUBBER BUSHING $0.45 Description REPLACEMENT PRESSURE SWITCH, (Contacts are open when switch is depressed) $7.19 7"DIA. BATHROOM FAN (NO LIGHT) 75 CFM capacity. Fits 8" Dia. opening in ceiling. Vent pipe is 7" Dia. Round white plastic inside grill. 120 VAC. Uses motor. Use roof cap listed below $ "DIA. BATHROOM FAN (NO LIGHT) 75 CFM(Cubic feet per minute) capacity. Fits 8" diameter opening in ceiling. Has 3"diameter round air discharge. 120 volts AC. Uses motor $45.00 BATHROOM FAN WITH LIGHT 75 cubic feet per minute air capacity. Fits 10" diameter ceiling opening. Fan is 5-5/8" high from ceiling flange to top of fan. Accommodates ceiling thickness up to 1-3/16". Has 3" diameter horizontal discharge. Ceiling grill/light-lens is 11-1/4" diameter. Has back-draft damper in air exhaust tube. Light fixture accepts standard 100 watt bulbs. 115 volt ac motor pulls 1.45 amp $ "DIA. BATHROOM FAN WITH LIGHT 75 CFM capacity. Fits 10-3/4" Dia. opening in ceiling. Vent pipe is 7" Dia. White powder coat trim with white plastic lens. 120 VAC. Uses motor. Use roof cap listed below $65.00 Page 68

11 *s are Subject to Change without Notice.* GRILL Bathroom Ceiling Fans This 9-3/4 diameter grill is made of white plastic. Comes with two metal spring fasteners $8.49 DAMPER ASSEMBLY Bathroom Ceiling Fans This 6-7/8 diameter damper is used on and comes with our & bath ceiling fans. Designed for quiet operation $4.99 DAMPER Range Hood Foam This 4-3/4 diameter foam damper fits 5 diameter vertical discharge range hoods by Ventline. Damper is designed to prevent insects from entering and to prevent air from escaping out the vent pipe when not in use $1.09 GRILL Bathroom Ceiling Fans Square white plastic grill is 3/8 thick at lip. Has a 1-3/8 solid border around a square grill area. Comes with two metal spring fasteners. Shipping weight is one pound. Description " x 9-1/4" $ /2" x 11-1/2" $18.98 LENS Light Bathroom Ceiling Fan Milky-white plastic lens is 7-7/8 diameter at top, 4-7/8 diameter at bottom and 1-7/16 deep. Has three mounting clips built into top of lens. Fit Ventlines V2280 series ceiling fans with light $6.69 LENS Light Bathroom Ceiling Fans 8-1/4 diameter light lens is made of white plastic. Used on our number ceiling fan $4.99 Flat Flange ROOF CAP ASSEMBLY Flat Flange 7-1/4 inside diameter pipe, 8-1/2 tall from flange to top of cap, 10 square flange/flashing for flat to slightly pitched roofs. Pipe protrudes approximately 1 below mounting flange. May be used with fan numbers & Made of galvanized steel $14.39 Slant Flange ROOF VENT Slant Flange 5 inside diameter pipe extends 13/16 below roof flange. Roof flange is 12-1/4 square and is not pre-drilled for fasteners. Vent is 7-7/8 tall from roof-line to top of cap. Slant flashing is made for 3-in-1 to 4- in-1 roof pitch. Made of galvanized steel $13.29 VINYL HOSE Vent Fan 3" Diameter This 3" diameter white vinyl flexible hose is designed for use with bathroom vent fans or similar uses. This product is not for use in areas that requires an insulated cover to prevent condensation. Comes in 50 ft. lengths. Will cut to length. d per foot $0.29 Page 69

12 *s are Subject to Change without Notice.* VENT HOOD ASSEMBLY Aluminum This all aluminum vent hood is designed for sloped roofs with or without shingles. Has a 4" or 6 diameter x 2" long tailpipe. Has screening to prevent insects from entering. Automatic aluminum damper closes when vent is not in use. Flashing is 10" wide x 11" long and is not pre-drilled for screw fasteners. May use reducer/increaser to change outlet pipe size where required. Description " DIA. $ " DIA. $21.69 VENT CAP ASSEMBLY Galvanized Steel Designed for flat to slightly pitched roofs. Has 2-7/8" diameter x 2-1/2" long tail pipe in which to fasten vent tubing. Height from top of cap to flashing is 3-1/2". Flashing is 8" square and is not pre-drilled for screw fasteners. Has a mesh screen to prevent insects from entering $11.98 EAVE VENT Bathroom Fan Galvanized Steel 5-1/2 inch overall diameter mounting flange with five predrilled mounting holes. Has a 2-7/8" outside diameter x 2-5/8" long round collar for mounting 3" diameter flexible vent hose. A fine galvanized mesh screen prevents insects from entering the opening. Made of galvanized steel $4.98 EAVE/SIDEWALL VENT Bathroom Fan Plastic INCREASER/REDUCER PVC Plastic This 4 x 3 increaser/reducer is made of heavy duty plastic and is 3 inside diameter on one end and 3-3/4 inside diameter on the other end $1.98 REDUCER Aluminum Made of light weight aluminum, this reducer is 4 diameter on one end (not crimped) and 3 diameter on the other end which is crimped $2.98 MOTOR MOUNTING BRACKET This plastic motor mounting bracket fits Ventlines V2270 series bathroom ceiling fans. They make a 50 CFM (cubic feet pre minute) and a 75 CFM fan. Each requires a different mounting bracket. The CFM rating can be found stamped into the mounting bracket. Description CFM $ CFM $5.99 SPRING FASTENER Bathroom Vent Fan Grille This V shaped spring fastener is used to hold grille in place on Ventline s V2262 series and V2270 series bathroom vent fans. Requires two per grille $ /8"overall diameter round mounting flange with four predrilled mounting holes. Has a 3"diameter x 1-7/8" long collar for mounting 3" diameter flexible vent hose. Has a fine mesh aluminum screen behind louvers to keep insects out. Louvers are slanted to prevent water from entering if used in a horizontal (sidewall) configuration. Made of white plastic $7.79 Page 70