Riaza Tablemount Fire Bowl. Item# Model# HYUTT DANGER If you smell gas: 1. Shut off gas to the appliance.

Transcription

1 Riaza Tablemount Fire Bowl Item# Model# HYUTT DANGER If you smell gas: 1. Shut off gas to the appliance. 3. If odor continues, keep away from the appliance and immediately call WARNING Do not store or use gasoline or other vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. Note: A table with an umbrella hole (not included) is required to assemble this product. WARNING For outdoor use only. WARNING Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the owner s manual thoroughly before installing or servicing this result causing property damage, personal injury or loss of life. Save these instructions for future use. If you are assembling this unit for someone else, give this manual to him or her and read and save for the future. Owner s Manual

2 SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so may result in a fire, explosion, injury or death. WARNING Do not use this firebowl for cooking. Do not burn any other materials than are supplied with and intended for use in this firebowl. Do not pour water into firebowl. The installation of this product must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSIZ223.1/NFPA 54, or CAN/CGA-B149.1, National Gas and Propane Installation Code. *Do not use this firebowl if any part has been under water. Do not store a spare or disconnected propane cylinder under or near this firebowl. After a period of storage, and/or non use, the propane firebowl should be checked for gas leaks and burner obstructions before use. Do not operate the propane firebowl if there is a gas leak present. Never use a flame to check for gas leaks. Combustible materials should never be within 48 inches of the top, back or sides of your propane firebowl. Do not put any other firebowl cover or anything flammable on, or beneath the firebowl. The propane firebowl should never be used by children. Children must be supervised when they are anywhere near the appliance. Users should be alerted to the hazards of high surface temperatures and keep a safe distance to avoid burning or clothing ignition. Pay attention when operating the firebowl. It is hot when in use and should never be left unattended. Do not transport it while in operation. Should fire go out while burning, turn the gas valve off. Wait five minutes before attempting to relight, then follow instructions to light the firebowl. Never use charcoal or any other solid fuel in the firebowl. Never place clothing or other flammable materials on or near the firebowl. Never lean over the open firebowl or place hands or fingers on the upper portion of an operational unit. Keep ventilation openings in cylinder enclosure (FIREBOWL BODY) free and clear of debris. Do not rest feet on the firebowl. Do not enlarge valve orifices or burner ports when cleaning the valve or burner. Propane gas is not natural gas. Only use propane for this firebowl. The conversion or attempted use of natural gas in a propane unit. Do not use this firebowl on vehicles or boats. Always operate the appliance on flat ground outdoors. Keep any electrical supply cord and the fuel supply hose away from any heated surfaces. Do not use this firebowl unless all parts are in place. Inspect the burner before each use of the appliance. If there is evidence of damage, the burner must be replaced prior to the appliance being put into operation. Use Manufacturer approved or supplied replacement burner only. FOR PROPANE GAS UNITS: The gas pressure regulator provide with the propane fire bowl must be used. Do not attempt to disconnect the gas regulator or any gas fitting while your firebowl is in operation. A dented or rusty propane cylinder may be hazardous and should be checked by your gas supplier prior to use. Do not use a propane cylinder with a damaged valve and any other worn out parts. Bond Manufacturing Company Page 2

3 Transport and store the empty gas cylinders carefully and properly. If you see, smell or hear the hiss of escaping gas from the propane cylinder: 1. Disconnect propane gas cylinder, 2. Do not attempt to correct the problem yourself, 3. Get to your gas supplier and/or the fire department for help. Any guard or other protective device removed for servicing this fire bowl must be replaced prior to operating this appliance. The maximum supply pressure is the 250 psi. This appliance is designed for use with a 16.40Z (1Lb) propane gas cylinder (disposable). The propane cylinder must be constructed and marked in accordance with the specifications for Gas cylinders of the U.S. Department of Transportation (DOT) or the National Standards of Canada, CAN/ CSA-B339, cylinders, Spheres and Tubes for Transportation of Dangerous Goods;and Commission,as applicable. Cylinders must be stored outdoors in well-ventilated area out of the reach of children. Disconnected cylinders must have valve caps tightly installed and must not be stored in a building or any other enclosed area. Do not light or use gas unit if lava rocks are wet. Ensure lava rocks are completely dry before igniting. Pumice stones/lava rocks/lavaglass could hit somebody s face or eyes during initial start of this unit, so please keep away from the firebowl for the first 20 minutes after it has been ignited. During Ignition procedure, one should NEVER get his/her face close to and or above the burner. In case of the unnoticed flame may suddenly be lit up and causing injury. Children should never operate this unit. Children must be supervised while near this unit. All installation and repair should be done by a qualified professional. This unit should be inspected annually and cleaned regularly. Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition. Young children should be carefully supervised when they are in the area of the appliance. Clothing or other flammable materials should not be hung from the appliance or placed on or near the appliance. Any guard or other protective device removed for servicing the appliance shall be replaced prior to operating the appliance. Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners and circulating airways of the appliance are kept clean. Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied directly by Bond Manufacturing Co. Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate the appliance. For assistance with repair or replacement of the burner or any other parts, calls Bond Manufacturing at NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned OFF before assembling. Do NOT attempt to assemble without proper tools Page 3

4 SAFETY INFORMATION Min. Clearance 48 in (121.9 cm) Min. Clearance 48 in (121.9 cm) Min. Clearance 48 in (121.9 cm) Combustible materials should not be within 48 inches of the top of the unit, or within 48 inches around the entire unit. Min. Clearance 48 in (121.9 cm) A table with an umbrella hole (not included) is required to assemble this product; shown to the right is an example of a table with an umbrella hole. HARDWAREARE AA BB CC DD Item Description Qty AA Screw 2 BB Nut 2 CC Wing Screw 1 DD Wing Nut 1 Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any parts are missing or damaged, do not begin assembly of this product and call customer service immediately. Estimated Assembly Time: 10 minutes Tools Required for Assembly (not included): Phillips Screwdriver Bond Manufacturing Company Page 4

5 CONTENTS B D A G E C F H Item Description Qty A Body 1 B Lava Rocks 1 bag C Control Knob (preassembled) 1 D Burner (preassembled) 1 E Support ring 1 F Regulator 1 G Angle Bracket 1 H Tank Bracket Page 5

6 ASSEMBLY INSTRUCTIONS 1. Attach the tank bracket (H) to angle bracket (G) using two screws (AA) and two nuts (BB). G AA BB H 2. Remove the support ring (E) from the body (A). Insert the body (A) through the umbrella hole in the table and the tank bracket assembly made in step 1. Screw the support ring (E) to the body (A) from the underside of the table to secure the body to the table. A E 3. Screw the regulator (F) to the body (A). A F Bond Manufacturing Company Page 6

7 4. Check that the control knob (C) for the gas supply system is turned to the OFF position before starting any assembly. To attach the 1 lb. propane gas tank (not included) on the unit, screw the 1 lb. gas tank to the C F 5. Once the tank is attached to the regulator, Insert the wing screw (CC) into the tank bracket and lock it by wing nut (DD) to secure the propane gas tank tightly. D anger Be cautious not to kick, jam or jar propane tank H CC DD 6. Place the bag of lava rocks (B) onto the burner (D) evenly. B D Page 7

8 OPERATION Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the off position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is repaired. Pumice stones/lava rocks/lavaglass could pop up and strike somebody s face during the process should be a yellow/blue color between inches in height. heating item. To Light 1. After assembling the gas tank, push and turn the control knob (C) counter-clockwise, then use a 2. To Extinguish 1. Turn the control knob (C) clockwise to the off position. 2. Disconnect propane cylinder to close the gas supply if not using for a period of time. MAINTENANCE Before performing any maintenance always disconnect propane gas tank. Keep the heating item free and clear from combustible materials. Visually inspect burner for obstructions and keep tank enclosure free and clear from debris. Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones/ lava rocks/lavaglass are completely cooled down. Wipe down with a soft cloth. Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting. Permanent damage may occur if powder or solvent comes in contact with painted or plastic components on this heating unit. Keep the heating unit stored away from direct sunlight. If storing this unit inside, disconnect the propane gas tank from the gas valve. Not using manufacturer approved or supplied parts/accessories may result in a defective condition and void the warranty of this heating unit. Always place lid (if applicable) or protective cover on heating item when not in use. Bond Manufacturing Company Page 8

9 TROUBLESHOOTING Problem Cause Solution Burner won t light with a match Heating unit emits a lot of black smoke Flame blows out easily No gas flow Regulator isn t connected securely to the tank Spider webs or insect nest in the burner and guard Burner ports are clogged Flame is obstructed at burner ports High or gusting winds No gas flow Check if gas cylinder is empty Tighten regulator connection to the gas tank Check the burner and guard Turn all gas flow connections off. Insert an opened paperclip (or similar item) into each of the burner ports to clear them out. Check that all burner ports are free of any small lava rocks/pumice stones/ LavaGlass pieces Increase flame to high Check if gas cylinder is empty Page 9

10 WARRANTY The manufacturer warranty will be voided by, and manufacturer disclaims any responsibility for, the following actions: Modification of the unit and/or components including the gas valve assembly. Use of any component part not manufactured or approved by Bond Manufacturing. Use and installation other than what is listed in this manual. Please contact the manufacturer for replacement parts. CONTACT If you have any questions or concerns, please contact Bond Manufacturing Company at the below resources: Toll Free Phone Online BOND (2663) Monday - Friday, 8am - 4:30pm PST customer.service@bondmfg.com Bond Manufacturing Company Page 10