Outdoor Refrigerated Drawers Tiroirs réfrigérés extérieur Gavetas refrigeradas exterior

Transcription

1 EN Installation, Operation and Maintenance Instructions FR Instructions d installation, d utilisation et d entretien ES Instrucciones de instalación, operación y mantenimiento Outdoor Refrigerated Drawers Tiroirs réfrigérés extérieur Gavetas refrigeradas exterior MO24RD

2 CONTENTS Contents: Safety information...2 Unpacking your appliance...3 Warranty registration...3 Installing your appliance...4 Cabinet clearances...4 Leveling the appliance...4 Electrical connection...5 Installing the anti-tip device...6 Energy saving tips...7 Product dimensions...8 Using your Electronic control...10 Starting your appliance...10 Turning your appliance "ON" or "OFF"...10 Adjusting the temperature...10 Refrigerator operation...10 Alarms...10 Door (drawer) ajar...10 Temperature sensor fault...10 Alarm mute...10 Care and cleaning...11 Long term storage / winterization...12 Stainless steel maintenance...13 Obtaining service...13 Troubleshooting...14 Warranty...15 Important Safety Instructions Warnings and safety instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating this appliance. Recognize Safety Symbols, Words, and Labels.! WARNING WARNING - You can be killed or seriously injured if you do not follow these instructions.! CAUTION CAUTION-Hazards or unsafe practices which could result in personal injury or property / product damage. NOTE NOTE-Important information to help assure a problem free installation and operation. State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.. 2 is committed to building a quality product in an environmentally friendly manner. Our processes are tightly controlled and closely monitored. We have achieved certifications in ISO 9001 for quality assurance, ISO for environmental management, and OHSAS for occupational health and safety from Lloyd s Register Quality Assurance.

3 UNPACKING YOUR APPLIANCE! WARNING EXCESSIVE WEIGHT HAZARD Use two or more people to move product. Failure to do so can result in personal injury. Remove Interior Packaging Your appliance has been packed for shipment with all parts that could be damaged by movement securely fastened. Remove internal packing materials and any tape holding internal components in place. The owners manual is shipped inside the product in a plastic bag along with the warranty registration card, and other accessory items. Important Keep your carton and packaging until your appliance has been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed as proof of damage in transit. Afterwards please dispose of all items responsibly. Warranty Registration It is important you send in your warranty registration card immediately after taking delivery of your appliance or you can register online at The following information will be required when registering your appliance. Service Number Rev. Letter Serial Number Date of Purchase Dealer s name and address Online registration available at The service number and serial number can be found on the serial plate which is located inside the cabinet on the bottom of the liner toward the left side. Open the bottom drawer to view it. See figure 1.! CAUTION Dispose of the plastic bags which can be a suffocation hazard. XXXXXXXXXXXX XXXXXXXXXXXX Note to Customer This merchandise was carefully packed and thoroughly inspected before leaving our plant. Responsibility for its safe delivery was assumed by the retailer upon acceptance of the shipment. Claims for loss or damage sustained in transit must be made to the retailer. Figure 1 NOTE DO NOT RETURN DAMAGED MERCHANDISE TO THE MANUFACTURER - FILE THE CLAIM WITH THE RETAILER.! CAUTION If the appliance was shipped, handled, or stored in other than an upright position for any period of time, allow the appliance to sit upright for a period of at least 24 hours before plugging in. This will assure oil returns to the compressor. Plugging the appliance in immediately may cause damage to internal parts.! CAUTION Help Prevent Tragedies Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous - even if they sit out for "just a few hours". If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents. Before you throw away your old refrigerator or freezer: Take off the doors or remove the drawers. Leave the shelves in place so children may not easily climb inside. 3

4 INSTALLING YOUR APPLIANCE Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To ensure your product performs to specifications, the recommended installation location temperature range is from 55 to 115 F (13 to 46 C). Front Grille, keep this area open. Cabinet Clearance Ventilation is required from the bottom front of the appliance. Keep this area open and clear of any obstructions. Adjacent cabinets and counter top can be installed around the appliance as long as the front grille remains unobstructed. Front Leveling Legs Figure 2 Rear Leveling Legs Leveling Legs Adjustable legs at the front and rear corners of the appliance should be set so the unit is firmly positioned on the floor and level from side to side and front to back. The overall height of your Marvel appliance may be adjusted between the minimum, " (85.7 cm), by turning the leveling leg in (CW ) and the maximum, " (88.3 cm) by turning the leveling leg out (CCW ).! CAUTION Front Grille Do not obstruct the front grille. The openings within the front grille allow air to flow through the condenser heat exchanger. Restrictions to this air flow will result in increased energy usage and loss of cooling capacity. For this reason it is important this area to not be obstructed and the grille openings kept clean. AGA MARVEL does not recommend the use of a custom made grille as air flow may be restricted. (See Figure 2). To adjust the leveling legs, place the appliance on a solid surface and protect the floor beneath the legs to avoid scratching the floor. With the assistance of another person, lean the appliance back to access the front leveling legs. Raise or lower the legs to the required dimension by turning the legs. Repeat this process for the rear by tilting the appliance forward using caution. On a level surface check the appliance for levelness and adjust accordingly. The front grille screws may be loosened and the grille adjusted to the desired height. When adjustment is complete tighten the two front grille screws. (See Figure 5). 4

5 INSTALLING YOUR APPLIANCE Figure 3 Do not remove ground prong! WARNING Electrical Shock Hazard Do not use an extension cord with this appliance. They can be hazardous and can degrade product performance. This appliance should not, under any circumstances, be installed to an un-grounded electrical supply. Do not remove the grounding prong from the power cord. (See Figure 3). Do not use an adapter. (See Figure 4). Do not splash or spray water from a hose on the appliance. Doing so may cause an electrical shock, which may result in severe injury or death. Figure 4 Electrical Connection A grounded 115 volt, 15 amp dedicated circuit is required. This product is factory equipped with a power supply cord that has a three-pronged, grounded plug. It must be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances (see Figure 6). If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to provide the proper power supply. The third ground prong should not, under any circumstances, be cut or removed. Figure 6 Figure 5 Front grille Front grille screw 5 NOTE Ground Fault Circuit Interrupters (GFCI) are prone to nuisance tripping which will cause the appliance to shut down. GFCI s are generally not used on circuits with power equipment that must run unattended for long periods of time, unless required to meet local building codes and ordinances.

6 INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS! WARNING Anti-Tip Bracket Leveling Leg ALL APPLIANCES CAN TIP RESULTING IN INJURY. INSTALL THE ANTI-TIP BRACKET PACKED WITH THE APPLIANCE " (54.6 cm) Bottom View of Refrigerated Drawer Unit FOLLOW THE INSTRUC- TIONS BELOW Front of cabinet Anti-Tip Device Figure 7! WARNING If your refrigerator is not located under a counter top (free standing), you must use an anti-tip device installed as per these instructions. If the refrigerator is removed from its location for any reason, make sure that the device is properly engaged with the anti-tip bracket when you push the refrigerator back into the original location. If the device is not properly engaged, there is a risk of the refrigerator tipping over, with the potential for property damage or personal injury. NOTE If installing on a concrete floor, concrete fasteners are required, (not included with the anti-tip kit).! CAUTION Any finished flooring should be protected with appropriate material to avoid damage when moving the unit. Floor Mount Installation The anti-tip bracket is to be located on the floor in the left or right rear corner of the refrigerator drawer as shown in Figure 7. 6 Step by step instructions for locating the position of the bracket: 1) Decide where you want to place the drawer refrigerator. Slide it into place, being careful not to damage the floor, leaving 1" (2.5 cm) of clearance from the rear wall to allow room for the anti-tip bracket. 2) Raise the rear leveling legs approximately 1 4" (6 mm) to allow engagement with the anti-tip bracket. Level the unit by adjusting all the leveling legs as required. Turning the leveling leg counterclockwise will raise the unit and clockwise will lower the unit. 3) Make sure the refrigerator is in the desired location, then mark on the floor the rear and side corner of the cabinet where the anti-tip bracket will be installed. If the installation does not allow marking the rear corner of the cabinet, then make temporary lines on the floor marking the front corner of the cabinet, excluding the drawer. Slide the refrigerator out of the way. From the temporary line extend the sidewall line back " (54.6 cm) as shown in Figure 8. 4) Align the anti-tip bracket to the marks on the floor so the side of the bracket lines up with the side of the cabinet mark, and the "V" notches on the anti-tip bracket line up with the end of the " (54.6 cm) line (Rear of cabinet line). 5) Fasten the anti-tip bracket to the floor using the supplied screw. (See Figure 8). 6) Slide the cabinet back into position, making sure the rear cabinet leveling leg slides under the anti-tip bracket engaging the slot.

7 INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS AND ENERGY SAVING TIPS NOTE When the floor mounted anti-tip bracket is used the minimum adjusted height of the cabinet is increased by 3 8" (9 mm). Front of cabinet line Side of cabinet line Rear Leveling leg Screw Figure 8a "V" notches in bracket " (54.6 cm) Figure 8 Rear of cabinet line "V" notches in bracket Energy saving tips: The following suggestions will minimize the cost of operating your refrigeration appliance. 1. Do not install your appliance next to a hot appliance (cooker, dishwasher, etc.), heating air duct, or other heat sources. 2. Install product out of direct sunlight. 3. Ensure the front grille vents at front of appliance beneath drawer are not obstructed and kept clean to allow ventilation for the refrigeration system to expel heat. 4. Plug your appliance into a dedicated power circuit. (Not shared with other appliances). 5. When initially loading your new product, or whenever large quantities of warm contents are placed within refrigerated storage compartment, minimize drawer openings for the next 12 hours to allow contents to pull down to compartment set temperature. 6. Maintaining a relatively full storage compartment will require less appliance run time than an empty compartment. 7. Ensure drawer closing is not obstructed by contents stored in your appliance. 8. Allow hot items to reach room temperature before placing in product. 9. Minimize drawer openings and duration of drawer openings. 10. Use the warmest temperature control set temperature that meets your personal preference and provides the proper storage for your stored contents. 11. When on vacation or away from home for extended periods, set the appliance to warmest acceptable temperature for the stored contents. 12. Set the control to the off position if cleaning the appliance requires the drawer to be open for an extended period of time. 7

8 PRODUCT DIMENSIONS ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS MODEL "A" "B" "C" "D" "E" "F" "G" "H" MO24RDS 24" (61 cm) **34" to 35" (86.4 cm to 88.9 cm) * " (60.7 cm) " to " (85.7 cm to 88.3 cm) " (60.2 cm) " (66.6 cm) " (99.5 cm) "A" "B" "E" Figure 9 "C" "D" Figure 9a Figure 10 8 If necessary to gain clearance inside the rough-in opening a hole can be cut through the adjacent cabinet and the power cord routed through this hole to a power outlet. Another way to increase the available opening depth is to recess the power outlet into the rear wall to gain the thickness of the power cord plug. Not all recessed outlet boxes will work for this application as they are too narrow, but a recessed outlet box equivalent to Arlington #DVFR1W is recommended for this application, (see Figure 10).

9 PRODUCT DIMENSIONS MODEL MO24RDS PRODUCT DATA ELECTRICAL REQUIREMENTS # 115V/60Hz/15A PRODUCT WEIGHT 130 lbs (59 kg) "D" "G" "F" "E" 1" (2.5 cm) Figure 11 * Depth dimension of rough-in opening may vary depending on each individual installation. To recess entire drawer "F" dimension plus 1" (2.5 cm) for thickness of power cord plug is required. "H" " (54.6 cm) Floor mount anti-tip bracket. ** Minimum rough-in opening required is to be larger than the adjusted height of the cabinet. # A grounded 15 amp dedicated circuit is required. Follow all local building codes when installing electrical and appliance.! WARNING Floor mount Anti-tip Bracket must be installed for freestanding applications. Not required for built in applications. 9

10 USING YOUR ELECTRONIC CONTROL Alarm F Set Colder Warmer ON/OFF Press and Hold Press and Hold Figure 12 close-up of control Starting your refrigerator Plug the refrigerator power cord into a wall outlet. Your refrigerator will begin cooling after power is applied. If your refrigerator does not start, check that the refrigerator is turned on and the set temperature is cold enough. Turning your refrigerator ON or OFF If the refrigerator is on, the refrigerator temperature will be shown on the display. To turn the refrigerator off, press and hold the "ON/OFF" button for three (3) seconds. "OFF" will appear on the display. If the refrigerator is not on, "OFF" will be shown on the display. To turn the refrigerator on, press and hold the "ON/ OFF" button for three (3) seconds. The refrigerator temperature will be shown on the display. Set temperature To set the refrigerator temperature, press and hold the "SET" button. When the "SET" button is pressed, the display will show the set temperature. While holding the "SET" button, press the "WARMER" or "COLDER" buttons to adjust set temperature. Refrigerator operation The available temperature range of the refrigerator is 34 to 42 F (1 to 6 C). It may take up to 24 hours for your refrigerator to reach desired temperature. This will depend on amount of content loaded and number of door opening and closings. For best results allow refrigerator to "pull down" to desired set temperature before loading. Once contents are loaded, allow at least 48 hours for temperature to stabilize before making any adjustments to the set temperature. Figure 13 Top drawer Alarms Your MARVEL Prime Controls will monitor refrigerator function and alert you with a series of audible and visual alarms. Door Ajar Alarm: If the door has been left open for over five (5) minutes, the alarm will sound in one (1) second intervals. The display panel will flash "do" and the Alarm LED located at the top left of the display below the word "Alarm" will be illuminated. This will stop as soon as the door is closed. Temperature Sensor Fault: If the controller detects that the temperature sensor is not properly functioning, a temperature sensor alarm will sound in one (1) second intervals. "E1" will flash on the display panel and the Alarm LED located at the top left of the display below the word "Alarm" will be illuminated. Please call AGA MARVEL Customer Service or your dealer if this error code is displayed. Alarm Mute Press any key to mute the audible portion of an alarm. NOTE-This action will only mute the alarm. If the condition that caused the alarm continues, the alarm code will continue to flash and will sound for 20 seconds every 60 minutes. 10

11 CARE AND CLEANING Care of Appliance 1. Avoid leaning on the drawer, you may bend the drawer hinges or tip the appliance. 2. Exercise caution when sweeping, vacuuming or mopping near the front of the appliance. Damage to the grille can occur. 3. Periodically clean the interior of the appliance as needed. Front Grille Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille area (see page 4).! CAUTION SHOCK HAZARD: Disconnect electrical power from the appliance before cleaning with soap and water. Cabinet The stainless steel cabinet can be washed with either a mild soap and water and thoroughly rinsed with clear water. NEVER use abrasive scouring cleaners. Dry thoroughly with a terry towel. Interior Wash interior compartment with mild soap and water. Do NOT use an abrasive cleaner, solvent, polish cleaner or undiluted detergent. In the Event of a Power Failure If a power failure occurs, try to correct it as soon as possible. Minimize the number of drawer openings while the power is off so as not to adversely affect the appliance's temperature. Light assembly replacement All models use an LED to illuminate the interior of the appliance. This component is very reliable, but should it fail, contact a qualified service technician for replacement of the LED. 11

12 CARE AND CLEANING Outdoor Product Long-Term Storage / Winterization: 1. Time to Winterize, when the daily low ambient temperature is at or below 38 F (3.3 C).! CAUTION 18. Do not place a cover on the unit, as this can trap condensation. After completion of the above, you may choose to store the unit indoors, although this is not required. Operation of the unit at ambient temperatures below the recommended Winterization temperature will void your warranty. 2. Turn unit off, (see page 10) 3. Remove all contents. 4. If necessary, move the unit so you can gain access to the rear of the product. 5. Unplug the unit from the power outlet. 6. It is also recommended that the power to the outlet be turned-off if the circuit is not required for other items during the Winter season. 7. When cleaning unit pay particular attention to any cracks and crevices that may have accumulated dirt and debris. 8. Remove the front toe-grille, (see Figure 14), and use a brush and vacuum to clean dirt and debris from beneath the unit. 9. Thoroughly clean the toe-grille and re-install on the unit. (See Figure 14). 10. Remove the rear access cover, (see Figure 15), and use a brush and vacuum to clean dirt and debris from the machine compartment. If the plastic defrost drain pan located under the compressor contains water, use a sponge to remove as much water as possible. 11. Thoroughly clean the rear access cover and re-install on the unit. 12. Wipe down all interior surfaces with anti-bacterial cleaner to be followed with clean rinse water to remove any residual chemicals which could cause staining. Do not use any abrasive cleaners or scouring pads. 13. Leave the drawers open and allow to completely dry out before closing the drawers. 14. Thoroughly clean the drawer gaskets with anti-bacterial cleaner to be followed with clean rinse water to remove any residual chemicals. 15. Thoroughly clean the exterior with a cleaner approved for stainless steel. Do not use any abrasive cleaners or scouring pads. See "Stainless Steel Maintenance" on page Any mounting hardware / fasteners that are showing signs of corrosion should be replaced. 17. Once the exterior has been thoroughly cleaned, you may want to apply a coating of car wax to help protect against spotting from moisture, dirt, and debris that may accumulate on the surfaces during the Winterization period. 12 Spacer Grille Remove screw from each end of grille Figure 15 Soak up water from plastic drain pan if necessary Remove the power cord from the grommet in the access cover. Figure 14 Clean out behind grille Clean out debris Remove screws around perimeter of access cover. Start-Up After Long-Term Storage: 1. If stored outside, it is recommended that the unit again be thoroughly inspected per the storage instructions above to address any dirt or debris from the weather and/or animals/insects. 2. Connect the unit to electrical power. 3. Turn unit on and confirm your desired control settings. 4. Allow 24-hrs for the unit to stabilize before loading contents.

13 STAINLESS STEEL MAINTENANCE AND OBTAINING SERVICE! WARNING Electrocution Hazard Never attempt to repair or perform maintenance on the appliance until the main electrical power has been disconnected. Turning the appliance control "OFF" does not remove electrical power from the unit's wiring. Replace all parts and panels before operating. Background Stainless steel does not stain, corrode, or rust as easily as ordinary steel, but it is not stain or corrosion proof. Stainless steels can discolor or corrode if not maintained properly. Stainless steels differ from ordinary carbon steels by the amount of chromium present. It is this chromium that provides an invisible protective film on the surface called chrome-oxide. This protective chrome-oxide film on the surface can be damaged or contaminated, which may result in discoloration, staining, or corrosion of the base metal. Care & Cleaning Routine cleaning of the stainless steel surfaces will serve to greatly extend the life of your product by removing contaminants. This is especially important in coastal areas which can expose the stainless to severe contaminants such as halide salts, (sodium chloride). It is strongly recommended to periodically inspect and thoroughly clean crevices, weld points, under gaskets, rivets, bolt heads, and any locations where small amounts of liquid could collect, become stagnant, and concentrate contaminates. Additionally, any mounting hardware that is showing signs of corrosion should be replaced. Although some products are called "stainless steel cleaners," some may contain abrasives which could scratch the surface, (compromising the protective chrome-oxide film), and some many contain chlorine bleach which will dull, tarnish or discolor the surface if not completely removed. After the stainless surfaces have been thoroughly cleaned, a good quality car wax may be applied to help maintain the finish. Note: Stainless steel products should never be installed, or stored in close proximity to chlorine chemicals. Whichever cleaning product you chose, it should be used in strict accordance with the instructions of the cleaner manufacturer. If Service is Required: If the product is within the first year warranty period please contact your dealer or call AGA MARVEL Customer Service at for directions on how to obtain warranty coverage in your area. If the product is outside the first year warranty period, AGA MARVEL Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www. agamarvel.com under the service and support section. In all correspondence regarding service, be sure to give the service number, serial number, and proof of purchase. Try to have information or description of nature of the problem, how long the appliance has been running, the room temperature, and any additional information that may be helpful in quickly solving the problem. Table "A" is provided for recording pertinent information regarding your product for future reference. Frequency of cleaning will depend upon the installation location, environmental, and usage conditions. Choosing a Cleaning Product The choice of a proper cleaning product is ultimately that of the consumer, and there are many products from which to choose. Depending upon the type of cleaning and the degree of contamination, some products are better than others. Typically the most effective and efficient means for routine cleaning of most stainless steel products is to give the surfaces a brisk rubbing with a soft cloth soaked in warm water and a gentle detergent, or mild mixture of ammonia. Rubbing should, to the extent possible, follow the polish lines of the steel, and always insure thorough rinsing after cleaning. 13 Date of Purchase Dealer s name Dealer s Address Dealer s City Dealer s State Dealer s Zip Code Appliance Serial Number Rev. Letter Appliance Service Number Date Warranty Card Sent (Must be within 10 days of purchase). For Your Records Table A

14 TROUBLESHOOTING Before You Call for Service If the appliance appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. However, it may be required to contact your dealer or a qualified service technician.! WARNING Electrocution Hazard Never attempt to repair or perform maintenance on the appliance until the main electrical power has been disconnected. Turning the appliance control "OFF" does not remove electrical power from the units wiring. Replace all parts and panels before operating. Appliance not cold enough Problem Possible Cause Remedy (See Adjusting the temperature" on page 10) Appliance too cold (See Adjusting the Temperature on page 10) Control set too warm Content temperature not stabilized. Excessive usage or prolonged drawer openings. Airflow to front grille blocked. Drawer gasket not sealing properly. Control set too cold Drawer gasket not sealing properly. No interior light. Failed LED light assembly or light switch. Light will not go out when drawer is closed Drawer not activating light switch. Failed light switch Noise or Vibration Appliance not level Fan hitting tube obstruction. Appliance will not run. Appliance turned off Power cord not plugged in. No power at outlet. 14 Adjust temperature colder. Allow 24 hours for temperature to stabilize. Allow temperature to stabilize for at least 24 hours. Airflow must not be obstructed to front grille. See clearances on page 4. Adjust or replace drawer gasket. Adjust temperature warmer. Allow 24 hours for temperature to stabilize. Adjust or replace drawer gasket. Contact a qualified service technician. Appliance not level, level appliance, (See page 4, leveling legs ) Contact a qualified service technician. Level appliance, see Leveling Legs on page 4. Contact a qualified service technician. Turn appliance on. See Starting your appliance on page 10. Plug in power cord. Check house circuit.

15 HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty AGA MARVEL warrants that it will supply all necessary parts and labor to repair or replace in the end user s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user. Additional Second Through Fifth Year Limited Parts Only Warranty During the four years following expiration of the one year limited warranty, AGA MARVEL will supply replacement parts for the hermetically sealed refrigeration system which consists of the compressor, condenser, drier, accumulator, bypass valve, connecting tubing and the evaporator that are proven to be defective due to workmanship or materials subject to the conditions and exclusions below. The above warranties do not cover: Shipping costs of replacement parts or returned defective parts. Customer education or instructions on how to use the appliance. Any content loss due to product failure. Removal or installation of product. Nor do the above warranties cover failure of this product or its components due to: Transportation or subsequent damages. Commercial use or use other than normal household or small office. Improper installation, misuse, abuse, accident or alteration, use of wiring not conforming to electrical codes, low or high voltages, failure to provide necessary maintenance, or other unreasonable use. Parts or Service Not Supplied or Designated by AGA MARVEL The above warranties also do not apply if: The original bill of sale, deliver date, or serial number cannot be verified. Defective parts are not returned for inspection if so requested by AGA MARVEL. The refrigeration equipment is not in the possession of the original end use purchaser. The warranties set forth herein are the only warranties extended by AGA MARVEL. Any implied warranties, including the implied warranty of merchantability, are limited to the duration of these express warranties. In no event shall AGA MARVEL be liable for any consequential or incidental damages or expenses resulting from breach of these or any other warranties, whether express or implied. Some states do not allow the exclusion or limitation of consequential damages or a limitation on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may have other rights that may vary from state to state. No person, firm, or corporation is authorized to make any other warranty or assume any other obligation for AGA MARVEL. These warranties apply only to products used in any of the fifty states of the United States and the District of Columbia. To obtain performance of this warranty, report any defects to: 1260 E. VanDeinse St. Greenville MI Phone:

16 E. VanDeinse St. Greenville MI EN Rev A 2/11/15 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.