Q/Tec TM QW-Series Water-to-Air Heat Pumps

Transcription

1 Heating Capacities: 6,4 to 45,5 BTUH Capacities:, to 53,5 BTUH : 3. to 3.5 : 3.4 to 6.6 Q/Tec TM QW-Series Water-to-Air Heat Pumps The Q/Tec series self contained packaged water-to-air heat pump is designed to be installed inside a building structure against an exterior exposed wall when ventilation option is selected. When no ventilation option is used, the QW-Series units can be installed in any interior space accessible to water supply system and condensate drain. Q/Tec s design provides whisper quiet operation with total comfort for the occupants at efficiency levels up to 24% above the federal standard. This design eliminates the need for roof-mounted equipment and outside condensing units and can meet your specific architectural requirements. Q/Tec s quiet technology provides extremely low indoor sound levels by using special components and materials in the construction of the unit. By using special motors and sound insulation we have built a heat pump system that is significantly quieter than competitive product available today. Q/Tec is suitable for both new construction and renovation projects for schools, modular buildings and light commercial buildings. A variety of ventilation options are designed to address your project s indoor air quality. The Q/Tec Series unique design allows all maintenance and service to be performed inside the building to facilitate multi-story installations. Access to air filters and controls is accomplished through a hinged front panel for easy accessibility. All Q/Tec Series models are built on heavy duty permanent rollers for easy installation and removal. Q/Tec s durable, easy to clean cabinet is aesthetically pleasing and comes standard with side and bottom trim pieces. Two types of cabinet finish are available: a durable two tone (slate and platinum) vinyl covered steel, or gray pre-painted steel. Product Features Scroll Compressor The Copeland scroll compressor has been designed for increased efficiency, quieter operation with reduced shutdown noise and improved reliability for longer life. Eliminates need for crankcase heater and suction line accumulator. Liquid Line Filter Drier Standard on all models. Phase Rotation Monitor Standard on all 3 phase scroll compressors. Protects against reverse rotation if power supply is not properly connected. Indoor Blower Motor feature a variable speed (ECM) motor providing super high efficiency, low sound levels and soft start capabilities. The motor is self adjusting to provide the proper airflow rate at high static pressure for ducted installations without user adjustment or wiring changes. High Efficiency Cupro-Nickel Coaxial Water Coil (Standard) Fully insulated to minimize sweating. Water piping connections are inch. Alternate copper water coil available - not for use with open wells. Pumping System Unit can be connected to central piping/pumping system from well field, boiler/tower or optional pump module can be installed inside unit for individual earth loop applications. Copper Tube/Aluminum Fin Evaporator Coil Grooved copper tubing and enhanced aluminum fins provide maximum heat transfer and high energy efficiency. Evaporator coil constructed with hydrophilic fin stock that seals fin surface against aluminum oxide formation, is resistant to mold and mildew growth (tested to ASTM D3273, no growth) and reduces beading of condensate on the fin surface. Cabinet Constructed of 2 gauge pre-painted or vinyl laminated galvanized steel. Choice of either two tone vinyl finish with slate front panels and platinum cabinet for designer appearance, or gray painted steel. Vinyl finish is very resistant to scratching and marring and is very easy to clean. Tamper resistant fasteners are provided for access panels. Unit includes built-in rollers for easy installation into wall sleeve and removal for service if necessary. Hinged, lockable front panel for filter service and access to primary functional electrical controls. Insulation Cabinet is fully insulated with foil covered, high density fiberglass insulation with sealed edge treatment and special sound deadening insulation material in the compressor section. All insulation is designed to resist mold and mildew growth and facilitate ease of cleaning. Electrical Components Are easily accessible for routine inspection and maintenance through front service panels. Circuit breaker standard on all 2/23V models and toggle disconnect standard on all 46V models. Circuit breaker/toggle disconnect access is through lockable access panel. Lock and key provided as standard equipment. Hot Water Coil A plenum mounted hot water coil is available for both free-blow and ducted applications. Air Filters One-inch disposable panel type air filters are standard. Optional two-inch pleated and two-inch fiberglass disposable air filters are available. Optional Energy Recovery Ventilator has a separate filter for exhaust air to keep ERV clean. Compressor Control Module Built-in off-delay timer adjustable from 3 seconds to 5 minutes. Two-minute on-delay if power interrupt. 2-second bypass for low pressure control, and both soft and manual lockouts for high and low pressure controls. High Pressure Switch Protects refrigerant circuit against excessively high pressure. Low Pressure Switch Provides loss of charge protection plus protects against freeze-up of coaxial coil during heating mode due to water flow or temperature problems. Two switches are installed, and the factory wired switch is for fresh water applications. Refrigerant Service Ports Located in filter compartment for easy access. Diagnostic Light System service - indicates high or low pressure switch operation for compressor protection. Located in inside control panel. Stainless Steel Drain Pan Provides extended life of the evaporator drain pan for maximum corrosion resistance. Side Trim Piece Extension Provides cabinet extension between interior wall and unit when wall thickness is 4 inches. Standard feature shipped with all models. Optional trim kits for thinner walls available. Optional Ventilation Packages Optional energy recovery ventilator can provide up to 45 cfm of outside air and exhaust through the unit while maintaining indoor comfort and humidity levels. Other available options include commercial room ventilator with exhaust, and barometric damper without exhaust. Outside wall and ventilation sleeve are required for installations with ventilation option. Optional Ventilation Wall Sleeve Required for ventilation options only. Constructed of 6 gauge galvanized steel, coated with epoxy primer and a baked on polyester enamel paint, which allows it to withstand hours of salt spray tests per ASTM B7-3. Ordered separately. Form No. S Supersedes S Page of 2

2 Specifications - 2, 2½ and 3 Ton MODELS LECTRICAL RATING--6 HZ perating Voltage Range COMPRESSOR-- CIRCUIT A oltage ated Load Amps ranch Circuit Selection Current ock Rotor Amps MOTOR & EVAPORATOR Blower Motor HP/SPD lower Motor--Amps CFM & E.S.P. w/filter (Rated-Wet Coil) ilter Sizes (inches) STD. HIPPING WEIGHT--LBS. -A 3/2 - -B 3/2 - -C QW32-A 3/2 - QW32-B 3/2 - QW32-C QW36-A 3/2 - QW36-B 3/2 - QW36-C E O V 23/ / /2 46 R 7.5/ / / / / /. 4. B L /2 / Variable /2 / Variable /2 / Variable B F - 6x2x & - 6x6x - 6x2x & - 6x6x - 6x2x & - 6x6x S 4 lb. 4 lb. 4 lb. Specifications - 3½, 4 and 5 Ton MODELS LECTRICAL RATING--6 HZ perating Voltage Range COMPRESSOR-- CIRCUIT A oltage ated Load Amps ranch Circuit Selection Current ock Rotor Amps MOTOR & EVAPORATOR Blower Motor HP/SPD lower Motor--Amps CFM & E.S.P. w/filter (Rated-Wet Coil) ilter Sizes (inches) STD. HIPPING WEIGHT--LBS. QW42-A 3/2 - QW42-B 3/2 - QW42-C QW4-A 3/2 - QW4-B 3/2 - QW4-C QW6-A 3/2 - QW6-B 3/2 - QW6-C E O V 23/ / /2 46 R 2./3. 9.2/ /7../ / / B L /2 / Variable /2 / Variable 3/4 / Variable B F - 6x2x & - 6x6x - 6x2x & - 6x6x - 6x2x & - 6x6x S 55 lb. 55 lb. 535 lb. See Page 7 for Electrical Specifications Indoor Blower Performance Model Rated ESP. Max. ESP Rated CFM 2 Optional CFM 3 Continuous CFM 4 Max ESP.. 5 N/ A 7 QW32.5. N/ A 9 QW QW QW QW Note: These units are equipped with a variable speed (ECM) indoor motor that automatically adjusts itself to maintain approximately the same rate of indoor air flow in both heating and cooling, dry and wet coil conditions and at both 23/2 or 46 volts. Max ESP (inches WC) shown is with " thick disposable filter (reduced by.2 for 2" filter) 2 Rated CFM (based on ducted application) for heating and cooling operation. To obtain full rated CFM on models QW36, QW42, QW4 and QW6, refer to Installation Instruction Reduced indoor air flow option to provide lowest possible indoor air sound level. Reduces system capacity performance by approx. 2%. 4 Continuous fan CFM is the total air being circulated during continuous fan mode. Form No. S Supersedes S Page 2 of 2

3 Capacity and Efficiency Ratings Capacity and Efficiency Ratings -- Ground Loop Heat Pump Application MODEL RATED CFM GPM COOLING 77 F EWT HEATING 32 F EWT 4, , QW32 6 2, , 3. 5 QW , , QW42 2 4, 6. 26, QW4 4 45, 5. 3, QW , ,5 3. Rated in accordance with ANSI/ARI/ASHRAE/ISO Standard 36-:9 Certified Water-to-Air and Brine-to-Air Heat Pump equipment which includes watt allowance for water pumping. capacity based on.6 F DB/66.2 F WB entering air temperature. Heating capacity based on 6 F DB entering air temperature. Capacity & Efficiency Ratings -- Ground Water Heat Pump Application (Pump & Dump) MODEL RATED CFM GPM COOLING 59 F EWT HEATING 5 F EWT 3 2, 23. 7, QW32 4 3, , 4. 3 QW , ,5 4. QW , ,5 4. QW , , 3. 7 QW ,5. 55, 3. 5 Ratings outside the scope of the ANSI/ARI/ASHRAE/ISO Standard 36-:9 Certified Water-to-Air and Brine-to-Air Heat Pump Certification Program. Includes watt allowance for water pumping. capacity based on.6 F DB/66.2 F WB entering air temperature. Heating capacity based on 6 F DB entering air temperature. Capacity and Efficiency Ratings -- Water Loop Heat Pump Application (Boiler/Tower) MODEL RATED CFM GPM COOLING 6 F EWT HEATING 6 F EWT 3, , QW32 4 2, , 4. 9 QW , , QW , , 4. 5 QW , , 4. 4 QW ,5 2. 7,5 4. Ratings outside the scope of the ANSI/ARI/ASHRAE/ISO Standard 36-:9 Certified Water-to-Air and Brine-to-Air Heat Pump Certification Program. Includes watt allowance for water pumping capacity based on.6 F DB/66.2 F WB entering air temperature. Heating capacity based on 6 F DB entering air temperature. Form No. S Supersedes S Page 3 of 2

4 Capacity and Efficiency Application Ratings - (Based on Fresh Water) DB/WB () /62 /67 5/72 DB () 6 QW32 DB/WB () /62 /67 5/72 DB () 6 CFM 3 GPM Capacity o F BTUH 29, 2,3 26,9,6 24,4 23,3 22,3 2,5 2,7 2,6 2,2 9,9 9,5 9,2,7,2 7,7 7,2 3, 3,3 3, 3,5 3, 29,7 29,2 2, 2, BTUH 3,7 3, 2,6 27,2,9 24,7 23,7 22, 22, 2,2 2, 2,5 2, 9,7 9,2,7,2 7,7 33, 32,6 32,2 3,7 3,3 3,9 3,4 3, 29, BTUH 34,9 33,2 3,5 3, 2,5 27,2 26,, 24,2 22,3 2,9 2,6 2,2 2,7 2,2 9,7 9,2,6 35, 34,6 34,2 33,7 33,2 32, 32,3 3, 3, Heating Capacity Heating BTUH 6, 6,5 7,4,2,9 9,6 2, Heat of Absorption, 2, 2,5 3, 3, 4,5 5, CFM 4 GPM Capacity o F BTUH 3, 29, 29,2 2,6 2, 27, 26,2, 23, 2,9 2,5 2, 2,7 2,3 9, 9,4 9,,6 34,5 34, 33,7 33,4 33, 32,6 32,3 32, 3, BTUH 3,9 3,6 3, 3,4 29,7 2, 27, 26,6,3 22,5 22, 2,7 2,3 2,9 2,4 2, 9,5 9, 35,9 35,5 35, 34,7 34,3 33,9 33,6 33,3 33, BTUH 35, 34, 34, 33,5 32,7 3,7 3,6 29,3 27,9 23,7 23,3 22, 22,4 22, 2,5 2, 2,5 2, 3, 37,7 37,3 36, 36,4 36, 35,7 35,3 35, Heating Capacity Heating BTUH,7 2, 23, 26, 29,3 32,7 36,3 Heat of Absorption 3,9 5, 7,4 2, 23, 26, 29, QW36 DB/WB () /62 /67 5/72 DB () 2 CFM 5 GPM Capacity o F BTUH 36,7 35,9 34,9 33,9 32,9 3,7 3,5 29,2 27, 27,6 27,2 26,7 26,2,7, 24,4 23,6 22,7 4, 4,9 4,2 39,4 3,6 3, 37,4 36, 36, BTUH 39, 3, 37, 36, 34,9 33,7 32,4 3, 29,5 2,4 2, 27,5 27, 26,4,, 24,3 23,4 43,5 42,6 4, 4, 4,2 39,5 3,9 3,3 37, BTUH 42,9 42, 4,9 39,6 3,4 37, 35,7 34, 32,5 29,9 29,4 2,9 2,4 27, 27, 26,4,6 24,6 46,2 45,2 44,4 43,5 42,7 4,9 4,3 4,6 4, Heating Capacity Heating BTUH 22, 23,5 26,6 3,2 34,3 39, 44,2 6 Heat of Absorption 5,3 6,6 9,7 23, 27, 3,2 35, () Return air temperatures Dry Bulb/Wet Bulb F. Legend: CFM = Cubic feet of airflow per minute (2) Requires antifreeze solution. GPM = Gallons of water flow per minute = Energy Efficiency Ratio = = Coefficient of Performance = Heating Units Watts Units Watts x 3.43 Form No. S Supersedes S Page 4 of 2

5 Capacity and Efficiency Application Ratings - (Based on Fresh Water) QW42 DB/WB () /62 /67 5/72 DB () 6 QW4 DB/WB () /62 /67 5/72 DB () 6 QW6 DB/WB () /62 /67 5/72 DB () 2 CFM 6 GPM Capacity o F BTUH 42, 4,9 39, 3, 37,6 36,6 35,6 34,5 33,4 29, 29,5 29, 2,9 2,5 2, 27,7 27,3 26,9 43,2 43, 44,4 45, 45,6 46, 46,4 46, 47, BTUH 44,6 43,5 42,3 4,2 4, 3,9 37, 36,6 35,5 3,7 3,4 3, 29,7 29,3 2,9 2,5 2, 27,7 44,9 45,6 46,2 46, 47,4 47,9 4,3 4,7 49, BTUH 49, 47,9 46,6 45,4 44, 42, 4,6 4,3 39, 32,3 32, 3,5 3,2 3, 3,4 3, 29,6 29, 47,6 4,4 49, 49,7 5,3 5, 5,2 5,7 52, Heating Capacity Heating BTUH 23,4,9 3,7 35,3 39,7 43,9 4, Heat of Absorption 7,,9 22,7 26,5 3,3 34, 37, CFM 6 GPM Capacity o F BTUH 47,9 47,2 46,4 45,3 43,9 42,3 4,7 3,7 36,5 35,3 35,5 34,6 34, 33,3 32,4 3,5 3,4 29, 56,9 56,2 55,5 54, 54, 53, 52,4 5,5 5, BTUH 5,9 5,2 49,3 4, 46,7 45, 43,2 4, 3, 36,3 36, 35,6 35, 34,3 33,4 32,4 3,3 3, 59,2 5,5 57, 57, 56,2 55,3 54,5 53,6 52, BTUH 56, 55,3 54,3 53, 5,4 49,5 47,6 45,3 42,7 3,2 37, 37,4 36, 36, 35, 34, 32,9 3,5 62, 62, 6,3 6,5 59,6 5,7 57, 56,9 55, Heating Capacity Heating BTUH 27, 29,5 34,7 39, 45, 5,4 55,7 Heat of Absorption 9,4 2,2, 29,4 34, 39, 44, CFM 9 GPM Capacity o F BTUH 6, 5, 56, 53,7 5,7 49,9 4,4 47,2 46,4 42, 42, 4, 4, 39, 3,2 37,2 36,2 35,3 74, 72,2 7, 6,2 66,7,5 64,7 64,2 64, BTUH,7 62,5 59,6 57, 54,9 53, 5,4 5,2 49,3 44, 43,2 42,3 4,3 4,3 39,3 3,3 37,3 36,3 77,9,2 72,9 7, 69,4 6,2 67,3 66, 66, BTUH 72,3 6,,6 62,9 6,4 5,3 56,6 55,3 54,3 46,4 45,4 44,5 43,4 42,4 4,3 4,3 39,2 3,2 2,6 79, 77,3,3 73,6 72,3 7,4 7,9 7, Heating Capacity Heating BTUH 4,9 44,5 5,2 56,5 63,5 7,2 79,4 6 Heat of Absorption 9,4 2,2, 29,4 34, 39, 44, () Return air temperatures Dry Bulb/Wet Bulb F. Legend: CFM = Cubic feet of airflow per minute (2) Requires antifreeze solution. GPM = Gallons of water flow per minute = Energy Efficiency Ratio = = Coefficient of Performance = Heating Units Watts Units Watts x 3.43 Form No. S Supersedes S Page 5 of 2

6 Water Coil Pressure Drop (Fresh Water) GPM P SIG Ft. Hd HEAT PUMP MODELS QW32 QW36, QW42, QW4 QW6 P SIG Ft. Hd P SIG Ft. Hd P SIG Ft. Hd Loop Pump Module and Pump Output Pump Model No. of Pumps WATER FLOW RATE REQUIRED IN GPM WGPM-C (w/cabinet) WGPM-2C (w/cabinet) Pump output (feet of GPM at top of column. Flow Rates for Various Fluids QW32 QW36 QW42 QW4 QW6 Flow rate required GPM fresh water Flow rate required GPM 5% Sodium Chloride Flow rate required GPM % GS Correction Factors for Performance at Other Water Flows Rated Flow Plus BTUH Heating Watts BTUH Watts 2 GPM GPM GPM GPM Form No. S Supersedes S Page 6 of 2

7 Ventilation System Packages Q-Tec models are designed to provide optional ventilation packages to meet all of your ventilation and indoor air quality requirements. All ventilation packages are factory installed. NOTE: A ventilation wall sleeve QWVS42 with outdoor louver grille is required for all installations that intend to utilize one of the built-in ventilation options of the QW-Series heat pumps. If a ventilation option is not to be utilized, do not order ventilation wall sleeve. BAROMETRIC FRESH AIR DAMPER OPTIONAL The barometric fresh air damper allows outside ventilation air, up to % of the total airflow rating of the unit, to be introduced through the ventilation louver grille and to be mixed with the conditioned air. The damper opens during blower operation and closes when the blower is off. Adjustable blade stops allow different amounts of outside air to be introduced into the building and can be easily locked closed if required. NOTE: The above vent systems are intake only without built-in exhaust capability. Building will likely require separate field installed barometric relief or mechanical exhaust elsewhere within the conditioned space. Balancing dampers in the return air grille may be required to achieve specified amount of outdoor air intake. COMMERCIAL ROOM VENTILATOR OPTIONAL The built-in commercial room ventilator is internally mounted and allows outside ventilation air, up to 5% of the total airflow rating of the unit, to be introduced through the ventilation louver grille. It includes a built-in exhaust air damper. Spring return on power loss or deactivation. The commercial room ventilator (CRV) is a simple and innovative approach to improving the indoor air quality by providing fresh air intake and exhaust capability through the CRV. The damper can be easily adjusted to control the amount of fresh air supplied into the building. The CRV can be controlled by indoor blower operation or field controlled based on room occupancy. Complies with ANSI/ASHRAE Standard 62. Ventilation for Acceptable Indoor Air Quality. Two Models Available: - Spring return on power loss or deactivation - Power return (will not close on power loss) ENERGY RECOVERY VENTILATOR OPTIONAL The energy recovery ventilator (ERV) is a highly innovative approach to meeting indoor air quality ventilation requirements as established by ANSI/ASHRAE Standard 62.. The ERV is internally mounted and allows up to 45 CFM (depending upon speed setting) of fresh air and exhaust through the unit while maintaining superior indoor comfort and humidity levels. In most cases this can be accomplished without increasing equipment sizing or operating costs. Heat transfer efficiency is up to 64% during summer and 79% during winter conditions. The ERV consists of a unique rotary energy recovery cassette that provides effective sensible and latent heat transfer capabilities during summer and winter conditions. Various control schemes are addressed including limiting ventilation during building occupancy only. The ERV has a filter for the exhaust air to keep the rotary wheels clean and free of any debris introduced through the room return air grille. The intake and exhaust rates can be independently selected. Factory set on medium intake and low exhaust. MODEL -AZ -BZ -CZ QW32-AZ QW32-BZ QW32-CZ QW36-AZ QW36-BZ QW36-CZ QW42-AZ QW42-BZ QW42-CZ QW4-AZ QW4-BZ QW4-CZ QW6-AZ QW6-BZ QW6-CZ RATED VOLTS & PHASE 23/2-23/ /2-23/ /2-23/ /2-23/ /2-23/ /2-23/ ELECTRICAL SPECIFICATIONS NO. FIELD POWER CIRCUITS 3 MINIMUM CIRCUIT AMPACITY MAXIMUM EXTERNAL FUSE OR CIRCUIT BREAKER FIELD POWER WIRE SIZE Maximum size of the time delay fuse or HACR type circuit breaker for protection of field wiring conductors. 2 Based on C copper wire. All wiring must conform to the National Electrical Code and all local codes. 3 These "Minimum Circuit Ampacity" values are to be used for sizing the field power conductors. Refer to the National Electrical Code (latest revision) article 3 for power conductor sizing GROUND WIRE SIZE Form No. S Supersedes S Page 7 of 2

8 Commercial Room Ventilator Performance Tables QH242 VENTILATION MODE CFM TABLE TABLE A 2 B C D E QH242 COOLING & HEATING MODE CFM A 22 2 B C D E QH32 Ventilation Mode CFM QH362 Ventilation Mode CFM QH422 Ventilation Mode CFM QH42 Ventilation Mode CFM TABLE 3 TABLE A B C D E QH32 COOLING & HEATING MODE CFM QH362 LOW SPEED COOLING & HEATING MODE CFM QH422 LOW SPEED COOLING & HEATING MODE CFM QH42 LOW APEED COOLING & HEATING MODE CFM A B C D E QH362 HIGH SPEED COOLING & HEATING MODE CFM QH422 HIGH SPEED COOLING & HEATING MODE CFM QH42 HIGH SPEED COOLING & HEATING MODE CFM TABLE 5 TABLE A 5 23 B C D E QH62 VENTILATION MODE CFM A 5 5 B 2 2 C D E QH62 COOLING & HEATING MODE CFM TABLE A B C D E NOTE: Ventilation airflow will increase up to 5 CFM during backup or emergency heat operation due to increased total airflow. Form No. S Supersedes S Page of 2

9 Energy Recovery Ventilator Performance Tables SUMMER COOLING PERFORMANCE (INDOOR DESIGN CONDITIONS DB / 62 WB) Ambient O.D. VENTILATION RATE 45 CFM % Efficiency VENTILATION RATE 3 CFM 66% Efficiency VENTILATION RATE 3 CFM 67% Efficiency DB/WB D egreesf V L T V L S V L L H R T H R S H R L V L T V L S V L L H R T H R S H R L V L T V L S V L L H R T H R S HR L Optional Hot Water Coil Performance - Heating F Water and 7 F Return Air LEGEND VLT = Ventilation Load HRT = Heat Recovery VLS = Ventilation Load HRS = Heat Recovery VLL = Ventilation Load Latent HRL = Heat Recovery Latent WINTER HEATING PERFORMANCE (INDOOR DESIGN CONDITIONS 7 F DB) Ambient O.D. VENTILATION RAT E DB Degrees F 4 5 CFM % Eff. 3 CFM % Eff. 3 CFM 2 Eff. W VL W H R W V L W H R W V L WH R LEGEND WVL=Winter Ventilation Load WHR=Winter Heat Recovery NOTE: performance only is shown for winter application. 9.5GPM 2GPM 4GPM 6GPM GPM GPM CFM Notes: Water connections are 7/" O.D. copper. 2 3-way flow valve is factory installed. 3 Control wiring included, and can be operated as either st or 2nd stage. Form No. S Supersedes S Page 9 of 2

10 Installation Overview of Ventilation Wall Sleeve Exterior Wall View NOTE: OPENING DIMENSIONS ARE ±. 29. MIS NOTE: Wall opening and wall sleeve required only when one of the ventilation options is utilized. Installations not utilizing any ventilation option can be made in any interior space accessible to electrical supply, water supply system and condensate drain. Unit and Wall Sleeve Opening Form No. S Supersedes S Page of 2

11 Installation Overview Unit Installed with Plenum Box Dimensions of Basic Unit for Architectural and Installation Requirements (Nominal) SEE NOTE SEE NOTE 2 NOTE : Ventilation intake opening for barometric fresh air damper, commercial room ventilator (CRV) or energy recovery ventilator (ERV). Opening is sealed if no vent option. NOTE 2: Ventilation exhaust opening for CRV and ERV vent options. Opening is sealed for no vent option and for barometric fresh air damper. Form No. S Supersedes S Page of 2

12 Q/Tec TM Model Nomenclature QW 36 A Z X X V X X X MODEL NUMBER QW - Q/TEC Model CAPACITY 24-2 Ton 3-2½ Ton 36-3 Ton 42-3½ Ton 4-4 Ton 6-5 Ton NOTE: QPBHW42-D-V NOTE: REVISION VOLTS & PHASE A - 23/2/6/ B - 23/2/6/3 C - 46/6/3 The following accessory items must be selected so that the finish (color) is matched to the QW-model that they will be used with. S ide Trim Extension Kits: Only required if wall sleeve and ventilation option installed. Required when wall thickness is less than 4 inches and works for walls down to inches thick. Used in place of standard trim kit supplied with unit to cover the space between unit and wall. Walls less than inches require custom field enclosure. QSTX42A-V QSTX42A-4 Gray paint Free-Blow Plenum Boxes: QPB42-V QPB42-4 Gray paint Front supply, 4-way deflection grille QPBS42-V QPBS42-4 Gray paint Same as QPB42, plus 2-way deflection grille on each side Top Fill Systems for Finishing Plenum Boxes to Ceilings: QPBX42-9-V QPBX G ray paint Use with QPB42 or QPBS42 (adjusts to ceilings up to 9' 6" ) QPBX42--V QPBX42--4 G ray paint Use with QPB42 or QPBS42 (adjusts to ceilings up to ' 2" ) Cabinet Extensions for Ducted Applications: QCXA-V QCXA-4 Gray paint 2" height (adjusts for ceilings up to 9' 4"; add QPBX42-9 for 9'4" to ' finished ceiling heights) Hot Water Coils with Plenum Boxes: QPBHW42-F-V QPBHW42-F-4 Gray paint Free-Blow plenum box See page for heating capacity performance QPBHW42-D-4 Gray paint KW Z - KW Ducted plenum box FILTER OPTIONS X - -Inch Fiberglass (Standard) F - 2-Inch Fiberglass P - 2-Inch Pleated COLOR V - Platinum w/slate Front (Vinyl) 4 - Buckeye Gray (Painted) VENTILATION OPTIONS X - Barometric Fresh Air (Standard) B - Blank-off Plate V - Commercial Ventilator - Motorized w/exhaust Spring Return P - Commercial Ventilator - Motorized w/exhaust Power Return R - Energy Recovery Ventilator w/independent Intake/ Exhaust Control The same top fill system and cabinet extensions can be used with hot water coil plenum boxes as with standard plenum boxes. COIL OPTIONS X - Standard evaporator coil Cupronickel water coil 4 - Standard evaporator coil- Copper water coil 2 CLIMATE CONTROL X - None A - Electronic/Non Prog D - Electronic/Prog E - Electronic/Prog/Humidistat G - Electronic Non-Prog/Humidistat INTERNAL CONTROLS X - Standard High Pressure Switch Low Pressure Switch Compressor Time Delay NOTE: Climate control option X, E or G must be ordered in conjunction with the dehumidification circuit. If X control option is selected, humidistat must be field supplied. For CS2A2 applications, order X control option for field supplied and installed thermostat and humidistat, or G control option for factory installed electronic non-programmable/man or Auto C/O thermostat and humidistat. G option can be used without CS2A2 only if X or B ventilation option is used, unless other control provisions are field supplied to limit ventilation to occupied periods. 2 For cooling tower or ground loop only, not for use with open wells. 3 Insert D for dehumidification with hot gas reheat. Reference Form F773 for complete details. Optional Field Installed Accessories - Must Be Used For Each Installatio n w/ventilation Option s Ventilation Wall Sleeves: Q WVS42 Ventilation wall sleeve for walls up to 4 inches thick. NOTE: F or walls from to 4 inches also order side trim extension kit QSTX42A-V or -4. See below. Ventilation Outdoor Louver Grilles: QLG- Clear Anodized Aluminum for vent option QLG-2 Medium Bronze Anodized Aluminum for vent option QLG-3 Dark Bronze Anodized Aluminum for vent option Optional Field Installed Accessories - For Ground Loop Installation s WGPM-C WGPM-2C WGRK- Single pump module for individual loop system. 22 feet of head 46V. Connections are inch FPT. Fully insulated cabinet. Dual pump module for individual loop system. 44 feet of head 46V. Connections are inch FPT. Fully insulated cabinet. 46V relay kit. Required when installing a pump module in a 46V 6 6 GPM. Optional Field Installed Accessories - For Water Coil Connections WGHK- WGAFC-3 WGAFC-4 WGAFC-5 WGAFC-6 WGAFC-9 SPECIALTY PRODUCTS 3 (Non-Standard) inch stainless assemblies. 3 GPM 4 GPM 5 GPM 6 GPM 9 GPM Installs inside QW unit. 23V 6Hz -Ph. Used with all models, includin g Installs inside QW unit. 23V 6Hz -Ph. Used with all models, includin g steel hose kit with ball valve, PT fittings, and union fitting with inch MPT both ends. Kit consists of two (2) completely assembled hose Automatic flow control assembly with strainer, inch ball valve, dual PT fittings, and drain valve. Order correct WGAFC by GPM requirements. The WGAFC assembly is used in conjunction with WGHK- hose kit when flow control is required. Optional Field Installed Accessories - Additional Items As Determined By Job Specification s Unit Compatibilit y Unit Compatibilit y Unit Compatibilit y Unit Compatibilit y Unit Compatibilit y Form No. S Supersedes S Page 2 of 2 Bard Manufacturing Company, Inc. Bryan, Ohio Due to our continuous product improvement policy, all specifications subject to change without notice. Before purchasing this appliance, read important energy cost and efficiency information available from your retailer. Form No. S3343 September, 27 Supersedes S