EA0045RC ELECTRIC FIREPLACE

Transcription

1 EA0045RC ELECTRIC FIREPLACE SAVE THIS MANUAL You will need this manual for safety instructions, operation procedures, and warranty. Put it and the original invoice in a safe, dry place for future reference. Table of Contents PAGE IMPORTANT SATETY INSTRUCTIONS 2 DIMENSIONS 3 TECHNICAL SPECIFICATIONS 3 WIRING DIAGRAM 3 ELECTRIC STOVE INSTALLATION 4 OPERATING INSTRUCTIONS 4 MAINTENANCE 5 TROUBLE SHOOTING 6 WARRANTY 6-0 -

2 IMPORTANT SAFETY INSTRUCTIONS: Warning: Any use of this appliance other than recommended by the manufacturer in these users manual may cause fire, burns, electric shock and /or other serious injuries When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons including the following: 1. Read all instructions before using this appliance. 2. This appliance is hot when in use. To avoid burns, don t let bare skin touch hot surfaces. The grill at the bottom of this heater in particular will become hot when the heater is active. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains etc. At least 3 feet( 0.9m)away from the front of the appliance. Keep all items away from the sides and back of the appliance and take special care not to block the air intake or exhaust vents. Use handles when moving this heater. 3. Extreme caution is necessary when the appliance is used by or near children or invalids and whenever the heater is left operating and unattended. 4. Do not operate the appliance if the power cord or plug has been damaged or the heater has been damaged or malfunctioned in any way. Take the appliance to authorized service facility for examination, electrical or mechanical adjustment or repair. 5. Do not use outdoors. 6. Do not use the appliance in bathrooms, laundry areas and similar indoor locations, Never locate the appliance where it may fall into a bathtub or other water container. 7. Do not run the power cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Take care to position the cord away from high traffic areas and such that it can not be tripped over. 8. To disconnect the appliance, turn all controls OFF, then remove the plug from the outlet. 9. This appliance has a polarized plug(one blade is wider than the other). This plug will fit in a fully in a outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way 10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the appliance. 11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces like a bed, where openings may become blocked. 12. A heater has hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint or flammable liquids are used or stored. 13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons. 14. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap. 15. Do not attempt burn wood or other materials in this heater 16. When transporting or storing the heater, take care to keep both the unit and power cord/plug dry, free from excessive vibration and away from heat sources. 17. This appliance comes equipped with an overheat protection safety device. Should the appliance begin to overheat for any reason, it will automatically turn all heater functions of the appliance off. The appliance will have to be reset prior to continuing use. To reset the overheat protection safety device, turn all controls, plug the appliance back and turn on SAVE THESE INSTRUCTIONS FOR FUTURE USE

3 DIMENSIONS: TECHNICAL SPECIFICATIONS Model# EA0045RC Rate Voltage AC 120V, 60Hz Rate Power(Total) 1400W Power of Heating Apparatus 650W/1300W Flame Power 80W Motor Power 20W Specification of the Bulb 2 pcs E12-2 -

4 ELECTRIC STOVE INSTALLATION Plugging in the heater NOTE: 1. This heater is for use on 120 Volts. 2. A 15AMP circuit is required to operate this appliance. If the breaker trips when the appliance is running, you may need to move the appliance to another location or unplug other appliances that are on the same circuit 3. ADAPTERS ARE NOT ALLOWED CANADA NOTE: A 15AMP,120 Volts circuit is required. Dedicated circuit is preferred but not essential in all cases, a dedicated circuit will be required if, after installation, the circuit breaker trips or the fuse blows on a regular basis when the heater is operating. Additional appliance on the same circuit may exceed the current rating of the circuit break. WARNING: 1. Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire, electric shock or injury to persons. 2. Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons. 3. Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. BEFORE USING THIS APPLIANCE: 1. Please check the circuit break for this appliance on? 2. Light bulbs may become loose during shipping, if the flame effect is dim or does not operate properly at first, ensure that the light bulbs are properly secured in the sockets(bulbs should be finger tight, don t over tighter) see Replacing Light Bulb section of this manual for instructions. 3. The information regarding this appliance can be found on the rating plate located on the back of the unit PLUGGING IN THE HEATER: 1. Make sure the appliance main I/O is switch OFF(refer to operating instruction section) 2. Plug the unit into a no less 15Amp/120V outlet

5 OPERATING INSTRUCTIONS NOTE: 1. When you first turn the heater on, it may emit a slight but harmless odor. This odor results from certain oils or greases being heated as the appliance is used for the first time. This odor is perfectly safe and will stop shortly, it will not reoccur after the first operation of the appliance. Control Panel Using the Control Panel: Master Power Switch(A) Open the cover and push button A down (1) to on position.(see FIG A) FLAME EFFECT Push O/I (On/Off) button (B) or O/I (On/Off) button (M) on the remote control to begin flame effect. The red power light and dimmer light will automatically come on. The flame effect can be adjusted by pressing the dimmer button (C) or dimmer button (L) on the remote control. When pressed, the red light will blink and the flame effect will cycle from high to low. Press the dimmer button (C) or dimmer button (L) on the remote control again to lock in desired flame brightness. The red light will remain on. This brightness will be kept until the dimmer button (C) or dimmer button (L) on the remote control is pressed again. HEAT SETTING 1. Turning on Master Power Switch (A) and O/I (On/Off) button (B) or O/I button (M) on the remote control 2. Press 650W button (D) or 650W button (K) on the remote control to active the low heater setting. The red light above will indicate that the heater is functioning on low. 3. Press 650W button (D) or 650W button (K) on the remote control again to shut off the heater. 4. Press 1300W button (E) or 1300W button (J) on the remote control to active the high heater setting. The red lights above 650W and 1300W buttons will indicate that the heater is functioning on high. 5. Press 1300W button (E) or 1300W button (J) on the remote control again to shut off the heater. Note When the heater begins to work, it will give off cool air for about 10 seconds before the heating function is activated - 4 -

6 Using the Remote Control This heater includes a remote control. To operate the appliance using the remote control, the Master Power Switch (A) must be the ON position. See below for directions to use the remote control: Note Light bulbs may become loose during shipping. If the flame effect is dim or does not operate properly at first, ensure that the light bulbs are properly secured in the sockets (bulbs should be finger tight, do not over tighten). See Replacing Light Bulbs Section of the manual for instructions. When you first turn the heater on, it may emit a slight but harmless odor resulting from certain oils or greases being heated as the appliance is used for the first time. This odor is perfectly safe and will stop shortly. It will not reoccur after the first operation of this appliance. This appliance comes equipped with an overheat protection safety device. Should the appliance begin to overheat for any reason, it will automatically turn all heater functions of the appliance off. The appliance will have to be reset prior to continuing use. To reset the overheat protection safety device, turn all controls off and unplug the appliance, wait 10 minutes, plug the appliance back in and turn on. MAINTENANCE Warning: Before attempting to perform any maintenance on this appliance, turn all controls to the OFF position and unplug. Allow the appliance to be OFF For at least 10 minutes before performing any maintenance in order to allow all components to cool properly. REPLACING LIGHT BULBS: 1. Ensure that all controls are off, the appliance is unplugged and bulbs are cool to the touch 2. Wear latex gloves to ensure that grease/oil from your hands does not transfer to the bulbs. 3. Remove back panel to access light bulbs.(see Fig B) 4. Remove the burnt out light bulb and replace with a new bulb. Hand tighten the bulbs only-do not over tighten. 5. Replace back panel and screws(see Fig B) Warning: Do not exceed the recommended Bulb wattage. Use only 120V, 40W, B10 chandelier light bulb, Candelabra Base. The lamp holder is model E12-5 -

7 CLEANING 1. To remove dust from glass window, please use clean dry cloth. 2. To remove fingerprints or other marks from glass window, please use clean damp cloth. Do not spray glass cleaner or other liquids directly onto the window. 3. Clean metal surfaces with a clean damp cloth making sure not to push dust or debris into any air intake or exhaust vents. 4. Do not use abrasive cleaners or spray liquids on any part of the appliance. TROUBLE SHOOTING Warning: Turn off the appliance, unplug and let cool for at least 10 minutes before attempting to service. Only a qualified professional should attempt to service or repair the appliance FREQUENTLY ASKED QUESTIONS(FAQS) PROBLEM POSSIBLE CAUSE SOLUTION Flame is dim or not present 1. Light bulbs are burnt out No warm air is coming from the heater The appliance turns off and will not turn back on 2. Flame wand has come loose from bracket 1.The overheat protection device in the appliance has been triggered 1.The overheat protection device in the appliance has been triggered 2. House circuit breaker has been tripped. 1. Inspect light bulbs and replace if necessary.(see Maintenance section of this manual) 2. Remove screws holding back panel in place and remove back panel. Secure end of flame wand back into the support bracket. 1. Turn all controls off, unplug the appliance, allow to cool for at least 10 minutes, plug back in and restart. 1. Turn all controls off, unplug the appliance, allow to cool for at least 10 minutes, plug back in and restart. 2. Reset house circuit breaker. WARRANTY Thank you for purchasing this product. These products have been made to demanding high quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights

8 For service within the warranty period, please contact the store where the product was purchased. Product model number and proof of purchase are required for any service request. We reserve the right to repair or replace the defective product, as its discretion Normal wear and tear, including accessory wear, it not covered under this warranty. The product is guaranteed for 12 months if used for normal trade purpose, and is valid for the original buyer only. Any warranty is deemed invalid if the product has been overloaded or used improperly, or subject to neglect or attempted repairs other than by an authorized agent. Heavy-duty,daily professional or hire usage are not guaranteed. We are not responsible for any costs related to labour, injuries or any other loss incurred during the product installation, repair or replacement, including any indirect or consequential damages If you have any problems with how the various functions operate or with internal damage or missing parts please call immediately. NOTE: DO NOT RETURN THIS PRODUCT TO THE STORE BEFORE CALLING THE TOLL FREE NUMBER. Due to continuous product improvement, we reserve the right to change the product specifications without prior notice