Section 4 of 6 DOAS Core Technologies
|
|
- Alfred Cory McDaniel
- 5 years ago
- Views:
Transcription
1 Section 4 of 6 DOAS Core Technologies Desiccant dehumidification Air-to-air energy recovery Evaporative cooling 1
2 Desiccant dehumidification Industrial Desiccant Dehumidifier Hybrid DX + Desiccant Dehumidifier 2
3 Desiccant vs. cooling dehumidification 3
4 Industrial desiccant dehumidification 4
5 Basic desiccant wheel performance Source: The Dehumidification Handbook - 2nd Edition (Munters, )..and leaves VERY dry, and hotter Process air enters at moderate temperature and humidity 5
6 Predicting desiccant DH performance Key variables Inlet air moisture Inlet air temperature Reactivation air temp. Process air velocity Source: Chapter 6 - Desiccant Dehumidifier Performance The Dehumidification Handbook - 2nd Edition (Munters, ) 6
7 Changing process air moisture The lower the moisture in......the lower the moisture of the leaving process air Note: This is different behavior than cooling-based DH, in which outlet dew point hits a lower limit regardless of inlet moisture. Moisture leaving cooling-based DH is limited by coil temperature 7
8 That s one good reason for bypass air......save energy by not drying any more air than necessary Bypass Air 8
9 Process air temperature The lower the temperature in......the lower the moisture of the leaving process air 9
10 That s one good reason for precooling the air... Smaller (less expensive) desiccant wheel does more more work Precool coil 10
11 Reduce process air velocity The slower the process velocity......the lower the moisture of the leaving process air BUT: when there s no VALUE to deep drying (as in commercial buildings) Higher velocity allows smaller, less expensive wheel and a smaller unit 11
12 That s one good reason commercial desiccants operate at higher velocity: No need for deep drying, so use smaller, less expensive wheels Higher velocity provides adequate drying using smaller wheels 12
13 Increase reactivation air temperature The hotter the reactivation temperature......the lower the moisture of the leaving process air BUT: when there s no VALUE to deep drying (as in commercial buildings) There s NO NEED to heat to high temperatures 13
14 That s one good reason for using condenser heat: When less drying required don t overheat reactivation for the required moisture removal Condenser heat reactivation 14
15 Process air temperature rise: First, understand the total heat of air Increasing total heat (Enthalpy) Increasing Increasing latent heat Latent heat: The heat that was needed to evaporate the water vapor in the air. More water vapor.. more latent heat sensible heat 15
16 Changing air s moisture content changes the air temperature along a line of constant total heat Spray water into the air.... the air cools down.....because the heat in the air is consumed to evaporate the water Remove water from the air.... the air heats up.....because the heat that originally evaporated the water is returned to the air 16
17 Desiccant process air temperature rise: Constant total heat + reactivation heat carryover Moisture removal temp rise Heat carryover temp rise 17
18 Reducing heat carryover is one reason for purge sectors for the desiccant wheel Post-purge Pre-purge 18
19 Condenser heat-reactivated desiccant behavior (General pattern - specifics vary) Note that the leaving air temperature is close to the same as the entering temperature.. but much drier 19
20 Heat recovery wheels - Peak Load Reducers 20
21 Heat transfer vs. moisture transfer efficiency 6-10 RPM adequate for heat transfer RPM needed for equal moisture transfer To avoid over-recovery of heat, wheel slows down, greatly reducing moisture transfer 21
22 Wheel stops during moderate temperature hours, to avoid overheating the building Greatest benefit is peak load reduction... Major reduction in size and cost of heating and cooling DOAS components 22
23 Ventilation air moisture load continues without load reduction whenever over-recovery of heat is problematic In other words... passive desiccant wheels cannot dry the air at all times DOAS systems still need to include a dedicated DH component 3317 hours without moisture load reduction (Palm Beach) 23
24 Evaporative cooling as DOAS components Direct evaporative cooling Low-energy cooling, by adding moisture to supply air Indirect evaporative cooling Low-energy cooling, by adding moisture to exhaust or outdoor air......while removing supply air heat through a plate or tube heat exchanger 24
25 Summary - DOAS component technologies Desiccant dehumidifiers Dries air very deeply - Sometimes not necessary to dry all supply air Adds heat to process air - Some cooling is needed Hybrid DX-Desiccant configuration is especially efficient (each kw dries the air twice, and dries with very little temperature rise) Heat recovery wheels Excellent way to reduce peak loads and save equipment cost Cannot always remove moisture a dedicated DH component is absolutely necessary in a DOAS unit Evaporative coolers Direct evaporative coolers provide low-cost, low-energy cooling but add moisture to supply air. Best for dry climates. Indirect evaporative coolers cost more, but provide very low-cost cooling without adding moisture to the supply air 25
Munters Heat Exchangers
Munters Heat Exchangers Brad Perdew Applications Engineer 8/27/12 DOAS Configurations Cheryl Hughes Regional Sales Manager October 11, 2016 cheryl.hughes@munters.com Munters DOAS Configurations Presentation
More informationPrinciples of Active Desiccant Operation. Presented by Tom Peterson, CEO and Founder. Climate by Design International
Principles of Active Desiccant Operation Presented by Tom Peterson, CEO and Founder Climate by Design International www.cdihvac.com Owatonna, MN 507-451-2198 4 02/2014 1 Dehumidification CDI is the Premier
More informationFAST AND ROBUST BUILDING SIMULATION SOFTWARE. Chilled Beam Performance: 1 Shelly Street, Sydney
FAST AND ROBUST BUILDING SIMULATION SOFTWARE Chilled Beam Performance: 1 Shelly Street, Sydney 3D Model Creation 1 Shelley Street, Sydney 3D Model Creation 1 Shelley Street, Sydney Daylight Analysis 1
More informationDEHUMIDIFICATION: Ice Arena Application & Product Guide. Design, construct and operate to control indoor humidity in ice rinks
DEHUMIDIFICATION: Ice Arena Application & Product Guide Design, construct and operate to control indoor humidity in ice rinks Munters is the world leader in dehumidification Munters is the largest manufacturer
More informationHeat Recovery Units. Heat Recovery 1
Heat Recovery Units Heat Recovery 1 Heat Recovery Unit Why? A heat recovery unit (HRU) can help make mechanical ventilation more cost effective by reclaiming energy from exhaust airflows. HRUs use air-to-air
More informationBy MIKE WEST, PHD, PE Advantek Consulting Inc. Melbourne, Fla.
Specifying S P E C I F I C A T I O N G U I D E 2 0 0 4 Dehumidifiers By MIKE WEST, PHD, PE Advantek Consulting Inc. Melbourne, Fla. Desiccant Desiccant dehumidifiers are used for lower-dew-point (below
More informationDehumidification for Industrial Coating Applications. By: Jay Kranker Munters MCS
Dehumidification for Industrial Coating Applications By: Jay Kranker Munters MCS Reasons for Using Dehumidification Construction/Coating Schedules New VOC Regulations Paint Specifications Adverse Weather
More informationBenefits Offered by Passive Dehumidification Wheel Speed Control
Benefits Offered by Passive Dehumidification Wheel Speed Control White paper By John Fischer Benefits Offered by Passive Dehumidification Wheel Speed Control The most significant advantage of the Pinnacle
More informationHeat pump and energy recovery systems
SBS5311 HVACR II http://ibse.hk/sbs5311/ Heat pump and energy recovery systems Ir. Dr. Sam C. M. Hui Faculty of Science and Technology E-mail: cmhui@vtc.edu.hk Oct 2017 Contents Basic concepts Air-to-air
More informationFeasibility of Controlling Heat and Enthalpy Wheel Effectiveness to Achieve Optimal Closed DOAS Operation
Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering July 2018 Feasibility of Controlling Heat and Enthalpy Wheel Effectiveness to
More informationPINNACLE SERIES DEDICATED OUTDOOR AIR SYSTEM ENERGY EFFICIENT DEHUMIDIFICATION
ENERGY EFFICIENT DEHUMIDIFICATION PINNACLE SERIES DEDICATED OUTDOOR AIR SYSTEM Provides a very high degree of latent cooling using only a minimal amount of conventional cooling input Substantial energy
More informationSummary Comparison of Simulation Program Features
Summary Comparison of Simulation Program Features FEATURE DOE2.2 equest TRACE 700 HAP Public/Proprietary Public Domain Proprietary Proprietary Proprietary Simulation Method 8760 hours 8760 hours 8760 hours
More informationState of the art building simulation software... Frenger Radiant chilled beam performance at 1 Shelly St - Sydney
Frenger Radiant chilled beam performance at 3D Model Creation Daylight Analysis Comparison of the performance of various HVAC systems at 1 Shelly St, Sydney VAV fancoil Active chilled beam Passive chilled
More information100% Outdoor Air Dehumidification Methods
Technical Bulletin 16 100% Outdoor Air ehumidification Methods I NTROUCTION As consulting engineers and end users implement the ASHRAE 6 ventilation code, they are faced with selecting an appropriate method
More informationHumidity Control & Psychrometrics
Humidity Control & Psychrometrics Iowa Chapter of ASHRAE March 22, 2017 R. Mark Nunnelly, P.E., CxA, LEED AP Nunnelly & Associates, Inc. Commissioning & Humidity Control Consulting Birmingham, AL mnunnelly@nunnellyengineering.com
More informationChapter 10. Passive Cooling Contents
Chapter 10. Passive Cooling Contents 10.1 Introduction to Cooling 10.2 Historical and Indigenous Use of Passive Cooling 10.3 Passive Cooling Systems 10.4 Comfort Ventilation VS Night Flush Cooling 10.5
More informationEfficient energy recovery in AHU. DOHA, Qatar Timo Schreck Enventus AB, Sweden
Efficient energy recovery in AHU DOHA, Qatar 11.04.2010 Timo Schreck Enventus AB, Sweden Main principles for cooling and dehumidification process in AHU 1. With cooling coil and reheater 2. Energy recovery
More informationAir Conditioning for and-humid Climates:
Air Conditioning for Hot-and and-humid Climates: Commercial Technologies ACEEE Market Transformation Conference Emerging Technologies March 21, 2007 Hugh I Henderson, Jr., P.E. CDH Energy Corp. Cazenovia,
More informationASHRAE Standard 90.1 Energy Requirements Wrap-Around Heat Pipes
ASHRAE Standard 90.1 Energy Requirements Wrap-Around Heat Pipes In Humid Climates BY DAVID A. JOHN, P.E., MEMBER ASHRAE; DREW ELSBERRY, MEMBER ASHRAE Designing g a building s HVAC system requires designers
More informationHCU Systems for Industrial Applications. Rob Smith National Accounts Manager March 7, 2011
HCU Systems for Industrial Applications Rob Smith National Accounts Manager Origins of the HCU The Humidity Control Unit (HCU) Hybrid Desiccant DX System Humidity Control Unit - DryCool HCU Introduced
More informationActive desiccant integration with packaged rooftop HVAC equipment
Applied Thermal Engineering 25 (2005) 3138 3148 www.elsevier.com/locate/apthermeng Active desiccant integration with packaged rooftop HVAC equipment James R. Sand a, *, John C. Fischer b a Oak Ridge National
More informationEnergy Recovery Ventilation
Published on Business Energy Advisor (https://oncor.bizenergyadvisor.com) Home > Energy Recovery Ventilation Energy Recovery Ventilation Proper ventilation is essential for maintaining good indoor-air
More informationChapter 14, Problem 27.
Chapter 14, Problem 27. A house contains air at 25 C and 65 percent relative humidity. Will any moisture condense on the inner surfaces of the windows when the temperature of the window drops to 10 C?
More informationDedicated Outdoor Air Systems: AHRI 920, ISMRE & ASHRAE 90.1
Dedicated Outdoor Air Systems: AHRI 920, ISMRE & ASHRAE 90.1 1 Peter Teige, Application Engineering Manager, AHRI Member Technical Training, October 12, 2016 AHRI 920: Establishes Efficiency Metric for
More informationNON-REVERSING, 100% OUTSIDE AIR HEAT PUMP FOR HEATING AND COOLING
NON-REVERSING, 100% OUTSIDE AIR HEAT PUMP FOR HEATING AND COOLING Danny Hall, National Sales Manager, Desert Aire Corp., Milwaukee, WI USA Traditionally, a heat pump has relied on a reversing valve system
More informationBOOK 1 OVERVIEW RD2XRT INSTALLATION AND OPERATION MANUAL. Table of Contents ABOUT BOOK 1:
4510 Helgesen Drive, Madison, WI, 53718 608.221.4499, 800.627.4499, Fax: 608.221.2824 support@renewaire.com www.renewaire.com RD2XRT INSTALLATION AND OPERATION MANUAL BOOK 1 OVERVIEW ABOUT BOOK 1: This
More informationHumidity Control Systems for Civil Buildings in Hot Summer and Cold. Winter Zone in China
Humidity Control Systems for Civil Buildings in Hot Summer and Cold Winter Zone in China Xiaoping Yu Doctoral Candidate Chongqing University of Science & Technology Chongqing, China, 400042 xiaoyup@163.com
More informationDES CHAMPS PRODUCTS. Specializing in: -- Air-to-Air Energy Recovery -- Conditioning Outdoor Air -- Controlling IAQ -- Indirect Evaporative Cooling
DES CHAMPS PRODUCTS Specializing in: -- Air-to-Air Energy Recovery -- Conditioning Outdoor Air -- Controlling IAQ -- Indirect Evaporative Cooling DES CHAMPS PRODUCTS Packaged Heat Recovery Systems Micro-Z
More informationDehumidifying with Dedicated Outdoor Air
Dehumidifying with Dedicated Outdoor Air System Configurations Figure 71. Configurations for dedicated outdoor-air systems A dedicated outdoor-air handler separately filters, cools, dehumidifies, heats,
More informationDesigning Energy Efficient Outdoor Air Systems
Designing Energy Efficient Outdoor Air Systems Joseph Thorndal Applied Products Sales Manager Greenheck, Schofield, Wisconsin 1 Joseph Thorndal BS Industrial Engineering North Dakota State University Work
More informationDehumidification: Energy Efficiency Comparisons
Fourth Annual Energy Management Workshop Cocoa, Florida February 10-11, 2003 Dehumidification: Energy Efficiency Comparisons Michael K. West, Ph.D., P.E. Building Systems Scientist Advantek Consulting,
More informationHumidity Control Design Tips. R. Mark Nunnelly, PE, CxA, LEED AP President
Humidity Control Design Tips R. Mark Nunnelly, PE, CxA, LEED AP President AIA Quality Assurance The Building Commissioning Association is a Registered Provider with The American Institute of Architects
More informationBOOK 1 OVERVIEW RD2XIN INSTALLATION AND OPERATION MANUAL. Table of Contents ABOUT BOOK 1:
4510 Helgesen Drive, Madison, WI, 53718 608.221.4499, 800.627.4499, Fax: 608.221.2824 support@renewaire.com www.renewaire.com RD2XIN INSTALLATION AND OPERATION MANUAL BOOK 1 OVERVIEW ABOUT BOOK 1: This
More informationTo Keep Docs Cool, Dry and Happy
To Keep Docs Cool, Dry and Happy David N. Schurk DES., CEM., LEED-AP., CDSM., SFP., CWEP. Director of Healthcare Accounts for Heat Transfer Solutions in Houston, TX. Learning Objectives 1. Understand the
More informationCHAPTER 4. HVAC DELIVERY SYSTEMS
CHAPTER 4. HVAC DELIVERY SYSTEMS 4.1 Introduction 4.2 Centralized System versus Individual System 4.3 Heat Transfer Fluids 4.4 CAV versus VAV Systems 4.5 Common Systems for Heating and Cooling 4.6 Economizer
More informationAvailable online at Energy Procedia 6 (2011) MEDGREEN 2011-LB
Available online at www.sciencedirect.com Energy Procedia 6 (2011) 759 768 MEDGREEN 2011-LB Comparison of two methods of improving dehumidification in air conditioning systems: hybrid system (refrigeration
More informationPsychrometric Engineering Applications
Psychrometric Engineering Applications Course No: M01-014 Credit: 1 PDH Klas Haglid, P.E., R.A. Continuing Education and Development, Inc. 9 Greyridge Farm Court Stony Point, NY 10980 P: (877) 322-5800
More informationENERGY EFFICIENCY WITH SUPERIOR INDOOR AIR QUALITY
SUPERIOR IAQ LOW FIRST COST BEST ROI ENERGY EFFICIENCY WITH SUPERIOR INDOOR AIR QUALITY Pinnacle manages 100% of a building s ventilation and indoor humidity load in a single package. Chilled beams have
More informationDesign Considerations For Dedicated OA Systems BY HUGH CROWTHER, P.ENG, MEMBER ASHRAE; YI TENG MA, ASSOCIATE MEMBER ASHRAE
ASHRAE www.ashrae.org. Used with permission from ASHRAE Journal. This article may not be copied nor distributed in either paper or digital form without ASHRAE s permission. For more information about ASHRAE,
More informationISSN: [Ghatol* et al., 6(12): December, 2017] Impact Factor: 4.116
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY HYBRID SOLAR DESICCANT COOLING SYSTEM Swapnil Ghatol *1, Tejaswini Rajput* 2 * Department of Mechanical Engineering, Siddhivinayak
More informationHEALTHCARE SURGERY VENTILATION HUMIDITY CONTROL
EFFECTIVE LOW DEW POINT EFFICIENT HEALTHCARE SURGERY VENTILATION HUMIDITY CONTROL HVAC systems have a major impact on: Specialized solution for the high demands of healthcare applications HVAC systems
More informationRelative Humidity in Schools Jim Cummings and Chuck Withers
to Co n tr o l Relative Humidity in Schools Jim Cummings and Chuck Withers SEEC Southern Energy-Efficiency Center Energy Efficient Strategies to Control Relative Humidity in Schools James Cummings and
More informationAHRI 920 Performance Rating and Comparisons of DX-DOAS Unit Efficiency
Application Note 24 AHRI 920 Performance Rating and Comparisons I NTRODUCTION In 2015, the Air-Conditioning, Heating, and Refrigeration Institute (AHRI) introduced a performance rating for dedicated outside
More informationImpact of Multi-Stage Liquid Desiccant Dehumidification in a Desiccant and Evaporative Cooling-Assisted Air Conditioning System
4 th International Conference On Building Energy Environment Impact of Multi-Stage Liquid Desiccant Dehumidification in a Desiccant and Evaporative Cooling-Assisted Air Conditioning System J Y Park H W
More informationWould You Bolt A Swamp Cooler To Your DX Rooftop Unit? [not exactly.]
Would You Bolt A Swamp Cooler To Your DX Rooftop Unit? [not exactly.] New Buildings Institute SWEEP-WCEC July 23, 2013 Evaporative Family Tree Evaporative Cooling Technologies Single Stage Evaporative
More informationASCENDANT CONVENTIONAL COOLING, ACTIVE DESICCANT DEHUMIDIFICATION SYSTEM ASCENDANT LOW DEW POINT EFFICIENT & EFFECTIVE
LOW DEW POINT EFFICIENT & EFFECTIVE ASCENDANT CONVENTIONAL COOLING, ACTIVE DESICCANT DEHUMIDIFICATION SYSTEM ASCENDANT HVAC systems have a major impact on: Specialized solution for the high demands of
More informationControlling Wrap-Around Heat Pipes for Systems with Strict Space Humidity Requirements. By Michael O. Davis, PE, August 2015
Controlling Wrap-Around Heat Pipes for Systems with Strict Space Humidity Requirements By Michael O. Davis, PE, August 2015 Advised by Heat Pipe Technology Background: HVAC systems are often designed to
More informationBuilding Systems: HVAC
Building Systems: HVAC Committee on Microbiomes of the Built Environment June 21, 2016 Washington DC Dennis Stanke (dstanke47@gmail.com) Retired rane (IR) Outline Ventilation Systems Moisture sources Low
More informationPERFORMANCE OF SOLID DESICCANT COOLING WITH SOLAR ENERGY IN HOT AND HUMID CLIMATE
Journal of Sustainability Science and Management Volume 9 Number 1, June 2014: 150-155 ISSN: 1823-8556 Penerbit UMT PERFORMANCE OF SOLID DESICCANT COOLING WITH SOLAR ENERGY IN HOT AND HUMID CLIMATE ARFIDIAN
More informationPRODUCT SERIES. VPR Series VPRX Series VPRE Series VPRP Series VPRC Series
PRODUCT SERIES VPR Series VPRX Series VPRE Series VPRP Series VPRC Series Valent Air Management Products Valent Air Management Systems designs and manufactures reliable, high-outdoor-air ventilators. Our
More informationDesiccant Cooling with Solar Energy
Desiccant Cooling with Solar Energy Gerrit Höfker 1,2, Ursula Eicker 2, Kevin Lomas 1, Herbert Eppel 1 1 De Montfort University Leicester, Institute of Energy and Sustainable Development 2 Hochschule für
More informationproduct application data PERFECT HUMIDITY DEHUMIDIFICATION SYSTEM
product application data PERFECT HUMIDITY DEHUMIDIFICATION SYSTEM 551B 581B DuraPac Plus Series Sizes 036-150 3to12 1 / 2 Tons Cancels: New PAD 551B.36.2 10/1/04 CONTENTS Page INTRODUCTION.................................
More informationChapter 14 GAS VAPOR MIXTURES AND AIR-CONDITIONING
Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 14 GAS VAPOR MIXTURES AND AIR-CONDITIONING Mehmet Kanoglu Copyright The McGraw-Hill Companies,
More informationD-PAC. Digital Precise Air Control System. Functionality Factory Testing Ease of Installation Ease of Maintenance Energy Efficiency
Digital Precise Air Control System D-PAC Functionality Factory Testing Ease of Installation Ease of Maintenance Energy Efficiency AAON 24 South Yukon Avenue Tulsa, Oklahoma 747 (918) 583-2266 Fax (918)
More informationSIMULATION ANALYSIS OF BUILDING HUMIDITY CONTROL AND ENERGY CONSUMPTION FOR DIFFERENT SYSTEM CONFIGURATIONS USA
Ninth International IBPSA Conference Montréal, Canada August 15-18, 25 SIMULATION ANALYSIS OF BUILDING HUMIDITY CONTROL AND ENERGY CONSUMPTION FOR DIFFERENT SYSTEM CONFIGURATIONS Chaoqin Zhai 1, Xiaohong
More informationAFD Industrial Dehumidifier Series
Dryomatic HUMIDITY CONTROL A MEMBER OF MARDUK HOLDING COMPANY LLC AFD Industrial Dehumidifier Series DRYOMATIC is a Leader in the Dehumidification Industry with Over 5 Years Experience and Thousands of
More informationWhite Paper. Executive Summary. Overview of Membrane Exchangers CLCH-PRB063A-EN. June 2017
White Paper Overview of Membrane Exchangers Executive Summary Membrane exchangers, also called enthalpy cores, are used to recover sensible and latent energy between exhaust air and outside air. The most
More informationExecutive Summary. OA/person (cfm/p) Private and open offices, Classrooms, Building as designed
Observations, ref ASHRAE May 2013 Journal article Vol. 55, NO 5, pg. 18 VAV Reheat vs. Active Chilled Beams & DOAS. Also published at: http://escholarship.org/uc/item/1jh193x3 Prepared by: S. A. Mumma,
More informationTrane CDQ Desiccant Dehumidification
Engineering Bulletin Trane CDQ Desiccant Dehumidification September 2004 CLCH-PRB020-EN Preface This engineering bulletin presents the Trane CDQ desiccant dehumidification system. It explains the features
More informationThomas J Kelly. Fundamentals of Refrigeration. Sr. Engineering Instructor Carrier Corporation. August 20, Page number: 1.
Thomas J Kelly Sr. Engineering Instructor Carrier Corporation August 20, 2003 1 SESSION OBJECTIVES At the conclusion of this session you should be able to: 1. Describe the basics principles of refrigeration
More informationEnergy-Efficient Makeup Air Units BY HUGH CROWTHER, P.ENG., MEMBER ASHRAE
This article was published in ASHRAE Journal, March 20145 Copyright 2015 ASHRAE. Posted at www.ashrae.org. This article may not be copied and/or distributed electronically or in paper form without permission
More informationTwo essential attributes of mechanical systems intended to
This pairing can represent a great strategy if you choose your tactics wisely. When is passive or active the better desiccant approach? When is one out of the question? We ll discuss how to control the
More informationComfort and health-indoor air quality
Comfort and health-indoor air quality 1 The human body has a complicated regulating system to maintain the human body temperature constant most of the time, which is 98.6 F (36.9 C) regardless of the environmental
More informationPassive building in Hot and Humid Climates
9 th Annual North American Passive House Conference Passive building in Hot and Humid Climates Lisa White 1 Overview 1. Thermal Comfort 2. Drivers of sensible and latent cooling loads 3. Passive cooling
More informationEVAPORATIVE AIR-COOLING EQUIPMENT
T CHAPTER 41 EVAPORATIVE AIR-COOLING EQUIPMENT Direct Evaporative Air Coolers... 41.1 Indirect Evaporative Air Coolers... 41.3 Indirect/Direct Combinations... 41.5 Air Washers... 41.6 Humidification/Dehumidification...
More informationA according to their application as (1) process-to-process, (2)
CHAPTER 44 AIR-TO-AIR ENERGY RECOVERY APPLICATIONS... 44.1 Economic Considerations... 44.1 Technical Considerations... 44.2 Energy Recovery Calculations... 44.7 Examples... 44.9 EQUIPMENT... 44.11 Fixed-Plate
More informationSECTION 5 COMMERCIAL REFRIGERATION UNIT 22 CONDENSERS UNIT OBJECTIVES UNIT OBJECTIVES 3/22/2012
SECTION 5 COMMERCIAL REFRIGERATION UNIT 22 CONDENSERS UNIT OBJECTIVES After studying this unit, the reader should be able to explain the purpose of the condenser in a refrigeration system. describe differences
More informationThermodynamics II Chapter 6 Mixtures & Psychrometry
Thermodynamics II Chapter 6 Mixtures & Psychrometry Mohsin Mohd Sies Fakulti Kejuruteraan Mekanikal, Universiti Teknologi Malaysia Objectives Differentiate between dry air and atmospheric air. Define and
More informationEnthalpy Wheel and its Application in Air Conditioning
Enthalpy Wheel and its Application in Air Conditioning Sathyanath M1, Sourav R2 1 2 Student, Dept of Mechanical Engineering, North Malabar Institute of Technology, Kanhangad, Kerela, India Student, Dept
More informationReview of Temperature and Humidity Control Technology for Air Conditioning and Heat Pump Systems Paper 2386
Review of Temperature and Humidity Control Technology for Air Conditioning and Heat Pump Systems Paper 2386 Xiaojie LIN 1, Yunho HWANG 1, Reinhard RADERMACHER 1, Saikee OH 2 1 Center for Environmental
More informationTOTAL SYSTEM EFFICIENCY: SYSTEM APPLICATIONS & DESIGNS. David Grassl PE Mechanical Engineer Principal
TOTAL SYSTEM EFFICIENCY: SYSTEM APPLICATIONS & DESIGNS David Grassl PE Mechanical Engineer Principal Similar to traditional boiler systems, condensing boiler systems have many designs they can operate
More informationEP SERIES PACKAGED ENERGY RECOVERY SYSTEM ENERGY EFFICIENT AIR COMFORT
ENERGY EFFICIENT AIR COMFORT EP SERIES PACKAGED ENERGY RECOVERY SYSTEM Certified total energy recovery performance (sensible and latent) up to 90% efficient. Double-wall panel construction eliminates exposed
More informationDesiccant Dehumidification in Air Conditioning for a Large Commercial Building
2333 Desiccant Dehumidification in Air Conditioning for a Large Commercial Building Hyun W Kim, Kamal Abou-Khamis Youngstown State University Abstract A case study was done to investigate the performance
More informationDehumidification System Enhancements
2006, American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. (www.ashrae.org). Published in ASHRAE Journal, (Vol. 48, February 2006). For personal use only. Additional distribution
More informationSession: HVAC 101 HVAC 101. Steve Sain Sain Engineering Associates, Inc. August 9, Rhode Island Convention Center Providence, Rhode Island
Session: HVAC 101 HVAC 101 Steve Sain Sain Engineering Associates, Inc. August 9, 2016 Rhode Island Convention Center Providence, Rhode Island Why? 2 Acknowledgements 3 Disclaimer I m gonna shoot down
More informationRSES Technical Institute Training Manual 2 72 hours, 72 NATE CEHs, 7.2 CEUs
Lesson 1 - Trade Tools Explain the importance of using proper tools and test instruments. List the various types of wrenches and describe their use. Describe the proper procedures for bending, flaring,
More informationEU Air Handling Units with SEMCO EXCLU-SIEVE
EU Air Handling Units with SEMCO EXCLU-SIEVE The acquisition of US based Semco has given us the opportunity to include a new range of rotary heat exchangers in our EU air handling unit range. Hygienic
More informationNEW FEATURES IN THE CARRIER HOURLY ANALYSIS PROGRAM v4.80
NEW FEATURES IN THE CARRIER HOURLY ANALYSIS PROGRAM v4.80 Carrier Software Systems Carrier Corporation Syracuse, New York rev October 10, 2013 Copyright 2013 Carrier Corporation, All Rights Reserved Page
More informationAdding More Fan Power Can Be a Good Thing
This article was published in ASHE Journal, May 14. Copyright 14 ASHE. Posted at www.ashrae.org. This article may not be copied and/or distributed electronically or in paper form without permission of
More informationASHRAE Region VI CRC Track III: Session 3 Ventilation Energy Recovery. Steven T. Taylor, PE Principal Taylor Engineering
ASHRAE Region VI CRC Track III: Session 3 Ventilation Energy Recovery Steven T. Taylor, PE Principal Taylor Engineering This program is registered with the AIA/CES for continuing professional education.
More informationDesiccant Cooling Analysis Simulation software, energy, cost and environmental analysis of desiccant cooling system
DEPARTMENT OF BUILDING, ENERGY AND ENVIRONMENTAL ENGINEERING Desiccant Cooling Analysis Simulation software, energy, cost and environmental analysis of desiccant cooling system Juan Artieda Urrutia June
More informationSIMULATION ANALYSIS ON THE FRESH AIR HANDLING UNIT WITH LIQUID DESICCANT TOTAL HEAT RECOVERY
SIMULATION ANALYSIS ON THE FRESH AIR HANDLING UNIT WITH LIQUID DESICCANT TOTAL HEAT RECOVERY Xiaoyun Xie, Yidan Tang, Xiaoqin Yi, Shuanqiang Liu,Yi Jiang Department of Building Science and Technology,
More informationComplete Ventilation, Heat Recovery and Dehumidification Packaged System by. Maintaining Your Climate for Indoor Pools and Waterparks
Ventilation Heat Recovery PoolPak International Maintaining Your Climate for Indoor Pools and Waterparks Complete Ventilation, Heat Recovery and Dehumidification Packaged System by PoolPak International
More informationME Mechanical Engineering Systems Laboratory. Experiment 3 - Mass and Energy Balances in Psychrometric Processes
ME 410 - Mechanical Engineering Systems Laboratory Experiment 3 - Mass and Energy Balances in Psychrometric Processes Assist.Prof.Dr. Özgür BAYER, A-123 AIR-CONDITIONING (A/C) Goal: Control temperature
More informationAIR CONDITIONING. Carrier Corporation 2002 Cat. No
AIR CONDITIONING Carrier Corporation 2002 Cat. No. 020-016 1. This refresher course covers topics contained in the AIR CONDITIONING specialty section of the North American Technician Excellence (NATE)
More informationImpact of indirect evaporative air cooler type on the performance of desiccant systems
Impact of indirect evaporative air cooler type on the performance of desiccant systems Anna Pacak 1,*, Aleksandra Cichoń 1, Demis Pandelidis 1, and Sergey Anisimov 1 1 Wrocław University of Science and
More informationRT-OA TM Rooftop Outdoor-Air (DOAS)
RT-OA TM Rooftop Outdoor-Air (DOAS) A/C s & HEAT PUMPS Dedicated Outside-Air System (DOAS) Solutions Office Buildings, Schools, Hospitals, Restaurants, Gyms & Fitness Centers, Hotels, Retail Stores...!
More informationInnovative and energy efficient humidity control. Peter Lau Application Manager Ingersoll Rand
Innovative and energy efficient humidity control Peter Lau Application Manager Ingersoll Rand CDQ (Cool Dry Quiet) : Dehumidification Innovative and energy efficient humidity control 2 CDQ (Cool Dry Quiet)
More informationField Test and Performance Verification: Integrated Active Desiccant Rooftop Hybrid System Installed in a School
ORNL/Sub-01-4000025209 Field Test and Performance Verification: Integrated Active Desiccant Rooftop Hybrid System Installed in a School Final Report: Phase 4a J. Fischer and J. Sand November 2005 DOCUMENT
More informationEnergy Use in Refrigeration Systems
2012 Rocky Mountain ASHRAE Technical Conference Energy Use in Refrigeration Systems PRESENTED BY: Scott Martin, PE, LEED AP BD+C Objectives Understand mechanical refrigeration terms Describe how heat is
More informationb.) Technical Information:
Section VI- Strategies a.) Summary: It is important for new construction designers to consider the heating, ventilation, and air conditioning needs within a building. There are many different systems,
More informationEvaporative Cooling Applicability in the Middle East
Evaporative Cooling Applicability in the Middle East Oxycom Fresh Air BV April 14th, 215 Abstract Oxycom developed various evaporative cooling solutions, either as standalone configurations or as combinations
More informationAustralian Solar Cooling Interest Group (ausscig) Conference
D.M. Whaley, W.Y. Saman, A. Alemu, Barbara Hardy Institute, University of South Australia, Mawson Lakes, South Australia, 5095 david.whaley@unisa.edu.au 1 Overview Introduction / Justification of research
More informationAchieving Dry Outside Air in an Energy-Efficient Manner
AT-01-7-2 Achieving Dry Outside Air in an Energy-Efficient Manner Stanley A. Mumma, Ph.D., P.E. Fellow ASHRAE Kurt M. Shank Student Member ASHRAE ABSTRACT The central thrust of this paper is to develop
More informationA NEW STANDARD FOR COOL COMFORT
A NEW STANDARD FOR COOL COMFORT Cotes heat-driven cooling solutions provide new levels of cool air capabilities that boost control, comfort and efficiency COTES.COM HOW IT WORKS COTES HEAT-DRIVEN COOLING
More informationExperimental Investigation of a Multi Effect Membrane Based Regenerator for High Concentration Aqueous LiCL Solution as Desiccant
Proceedings of the World Congress on Momentum, Heat and Mass Transfer (MHMT 16) Prague, Czech Republic April 4 5, 216 Paper No. ENFHT 111 DOI: 1.11159/enfht16.111 Experimental Investigation of a Multi
More informationMystery of Sustainable Heat Exchange Material Heat Recovery Ventilator(HRV)
Mystery of Sustainable Heat Exchange Material Heat Recovery Ventilator(HRV) 1 Contents Why Heat Recovery Ventilator(HRV) is required Type of Heat Recovery Ventilator Feature of MITSUBISHI ELECTRIC Lossnay
More informationCompressor Confusion: Field Findings on the Role of Supplemental Cooling in a Commercial Indirect Evaporative Air Conditioner
Compressor Confusion: Field Findings on the Role of Supplemental Cooling in a Commercial Indirect Evaporative Air Conditioner Cathy Higgins and Howard Reichmuth, New Buildings Institute ABSTRACT The market
More informationMunters DesiCool removes excess heat in server room
Munters DesiCool removes excess heat in server room DesiCool Corporate IT in Copenhagen University is bringing all their servers into two large server rooms located respectively in Copenhagen University
More information7. MECHANICAL SYSTEM DESIGN
7. MECHANICAL SYSTEM DESIGN The second primary topic of this thesis is to investigate the application of a dedicated outdoor air system (DOAS) to the SLCC. The stated goals for this thesis of improved
More information