Owner s Manual. Room Air Conditioner with R-410A: BG-81P BG-101P BG-103P BG-121P BG-123P BG-143M BGE-103M BGE-123M BGE-143M.

Transcription

1 Owner s Manual Room Air Conditioner with R-410A: BG-81P BG-101P BG-103P BG-121P BG-123P BG-143M BGE-103M BGE-123M BGE-143M

2 IMPORTANT SAFETY INSTRUCTIONS READ THIS MANUAL Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over life of your air conditioner. You'll find many answers to common problems in chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. To prevent injury to user or or people and property damage, following instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The seriousness is classified by following indications. WARNING CAUTION This symbol indicates possibility of death or serious injury. This symbol indicates possibility of injury or damage to property. Never do this. Always do this. WARNING Plug in power plug properly. May cause electric shock or fire due to excess heat generation. Always install circuit breaker and a dedicated power circuit. Incorrect installation may cause fire and electric shock. Always ensure effective grounding. Do not operate or stop unit by inserting or pulling out power plug. May cause electric shock or fire due to heat generation. Do not operate with wet hands or in damp environment. May cause electric shock. Do not allow water to run into electric parts. Do not damage or use an unspecified power cord. May cause electric shock or fire. If power cord is damaged, it must be replaced by manufacturer or an authorized service center or a similarly qualified person in order to avoid a hazard. Do not direct airflow at room occupants. This could damage your health. Do not modify power cord length or share outlet with or appliances. Incorrect grounding may cause electric shock. Unplug unit if strange sounds, smell, or smoke come from it. May cause fire and electric shock. Keep firearms away. It may cause fire. Ventilate room before operating air conditioner if re is a gas leak from anor appliance. May cause explosion, fire and, burns. May cause failure of machine or electric shock. Do not use socket if it is loose or damaged. May cause fire and electric shock. Do not use power cord close to heating appliances. May cause fire and electric shock. May cause electric shock or fire due to heat generation. Do not open unit during operation. May cause electric shock. Do not use power cord near flammable gas or combustibles, such as gasoline, benzene, thinner, etc. May cause an explosion or fire. Do not disassemble or modify unit. May cause failure and electric shock. 2

3 IMPORTANT SAFETY INSTRUCTIONS When air filter is to be removed, do not touch metal parts of unit. May cause an injury. Do not use strong detergents, wax or thinner; use a soft cloth only. Finish may be damaged. Operation with windows open may cause wetting of indoor and soaking of household furniture. CAUTION Stop operation and close windows in storm or hurricane. Clean filter once every t wo weeks. Do not put a pet or house plant where it will be exposed to direct air flow. This could injure pet or plant. Do not clean air conditioner with water. Water may enter unit and degrade insulation. It may cause an electric shock. When unit is to be cleaned, switch off, and unplug. Do not clean unit when power is on as it may cause fire, electric shock, or injury. Hold plug by head of power plug when taking it out. Ventilate room well when used toger with a stove, etc. An oxygen shortage may occur. Do not use for or than human comfort. Do not use this air conditioner to preserve precision devices, food, pets, plants or art objects. It may cause deterioration of quality, etc. If bracket is damaged, re is concern of damage or injury due to falling of unit. Ensure that outdoor support bracket is not damaged due to prolonged exposure. Disconnect power when not using unit for a long time. Operation without filters may cause failure. It may cause appliance failure or accident. shock. Use caution when unpacking and installing. Sharp edges could cause injury. Do not place obstacles around air-inlets or inside of air-outlet. May cause electric shock and damage. Do not place heavy objects on power cord and ensure that cord is not compressed. There is danger of fire or electric May cause failure of product or fire. Do not drink water drained from air conditioner. It contains contaminants and could make you sick. If water enters unit, turn unit off at power outlet and switch off circuit breaker. Isolate supply by taking power-plug out and contact a qualified service technician. CAUTION This appliance is not intended for use by persons (including children) with reduced physical,sensory or mental capabilities or lack of experience and knowledge, unless t hey have b een gi ven supervision or instruction concerning use of appliance by a person responsible for ir safety. Children should be supervised to ensure that y do not play with appliance. If supply cord is damaged, it must be replaced by manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. This appliance should be installed in accordance with national wiring regulations. Do not operate your air conditioner in a wet room such as a bathroom or laundry room. The appliance with electric heater shall have at least 3 ft. space to co mbustible materials. Contact an authorized service technician for repair or maintenance of this unit. Contact an authorized installer for installation of this unit. 3

4 IMPORTANT SAFETY INSTRUCTIONS NOTE: The power supply cord with this air conditioner contains a current detection device designed to reduce risk of fire. Please refer to section "Operation of Current Device" for details. In event that power supply cord is damaged, it cannot be repaired-it must be replaced with a cord from Product Manufacturer. WARNING Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prong from power cord. Grounding type wall receptacle Do not, under any circumstances, cut, remove, or bypass grounding prong. Power supply cord with 3-prong grounding plug and current detection device WARNING For Your Safety Do not store or use gasoline or or flammable vapors and liquids in vicinity of this or any or appliance. WARNING WARNING Operation of Current Device (Applicable to unit using current detection device only ) The power supply cord contains a current device that senses damage to power cord. To test your power supply cord do following: 1. Plug in Air Conditioner. 2. The power supply cord will have TWO buttons on plug head. Press TEST button, you will notice a click as RESET button pops out. 3. Press RESET button, again you will notice a click as button engages. 4. The power supply cord is now supplying electricity to unit. (On some products this is also indicated by a light on plug head.) Prevent Accidents To reduce risk of fire, electrical shock, or injury to persons when using your air conditioner, follow basic precautions, including following: Be sure electrical service is adequate for model you have chosen. This information can be found on serial plate, which is located on side of cabinet and behind grille. If air conditioner is to b e in stalled in a window, yo u will probably want to clean both sides of glass first. If th e window is a triple-track type with a screen panel included, remove screen completely before installation. Be sure air conditioner h as been securely an d correctly installed according to installation instructions in this manual. Save this manual for possible future use in removing or installing this unit. When handling air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils. Electrical Information The complete electical rating of your new room air conditioner is stated on serial plate. Refer to rating when checking electrical requirements. Be sure air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. Your air conditioner must be used in a properly grounded wall receptacle. If wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install proper receptacle. Ensure receptacle is accessible after unit installation. Do not run air conditioner without side protective cover in place.this could result in mechanical damage within air conditioner. Do not use an extension cord or an adapter plug. Do not use this device to turn unit on or off. Always make sure RESET button is pushed in for correct operation. The power supply must be replaced if it fails reset when eir TEST button is pushed, or it cannot be reset. A new one can be obtained from product manufacturer. If power supply cord is damaged, it cannot be repaired. It MUST be replaced by one obtained from product manufacturer. NOTE:This air conditioner is designed to be operated under following conditions: 4 NOTE: Cooling operation Heating operation Outdoor temp: Indoor temp: Outdoor temp: Indoor temp: O O O O F/18-43 C ( F/18-52 C for special tropical models) O O F/17-32 C O O F/-5-24 C O O F/0-27 C Note: Performance may be reduced outside of se operating temperatures.

5 BEFORE YOU BEGIN Read se instructions completely and carefully. IMPORTANT- Save se instructions for local inspector s use. IMPORTANT- Observe all governing codes and ordinances. Note to Installer- Be sure to leave se instructions with Consumer. Note to Consumer- Keep se instructions for future reference. Skill level- Installation of this appliance requires basic mechanical skills. Completion time- Approximately 1 hour. We recommend that two people install this product. Proper installation is responsibility of installer. Product failure due to improper installation is not covered under Warranty. You MUST use all supplied parts and use proper installation procedures as described in se instructions when installing this air conditioner. CAUTION Do not, under any circumstances, cut or remove third (ground) prong from power cord. Do not change plug on power cord of air conditioner. Aluminum house wiring may present special problemsconsult a qualified electrician. When handling unit, be careful to avoid cuts from sharp metal edges and aluminum fins on front and rear coils. Do This First (for existing sleeve) Note that air conditioner dimensions are: 24 inches wide, 14 inches high, and 18 inches deep(without front). Install Air Conditioner according to se installation instructions to achieve best performance. Save se installation instructions for future reference. NOTE: Do not use any screws or than those specified here. Items in Kit You may not need all parts in kit. Discard unused parts. Name Spec. Qty Tapered Spacer Blocks 17 Long 2 Centering/Support Blocks 4 1 /2 x3 1 1 /2 x1 /2 4 Plastic Divider 1/8 x4 1 /2 x14 1 /2 2 Stuffer Seal 1 x1 1 /2 x84 1 Seal 1 x1 1 /2 x25 3 Seal 1 x1 1 /2 x14 2 Seal 1 x3/8 x25 3 Seal 1 x3/8 x14 2 Seal 1 x3/4 x14 2 Trim Frame(side legs) 2 2 Trim Frame(top & bottom legs) Ground Wire(green) Tood Washer for grounding screw Grounding Screw Grille(plastic) Grille Aluminum Nuts(plastic) Screw Washer Screw NOTE: Save Carton and se Installation Instructions for future reference. The carton is best way to store unit during winter, or when not in use

6 How to Install 1. Identify wall-sleeve brand for your installation, from chart below. Brand Wall Sleeve Dimensions (inches) Width Height Depth White-Westinghouse Frigidaire Carrier(52F Series) General Electric/Hotpoint Whirlpool Fedders/Emerson Sears/Kenmore Carrier(51S Series) Emerson/Fedders Friedrich 251/2 151/4 16,171/2 or /8 15 7/8 257/8 161/2 171/8 or /4 163/4 or 19 3/4 253/4 167/8 18 5/8 263/4 153/4 15 3/ NOTE: All wall sleeves used to mount new Air Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve, or rear flange that serves as a stop for Air Conditioner. CAUTION: When installation is complete, replacement unit MUST have a rearward slope as shown. REAR Wall Sleeve / UNIT 1 /4 to 5 /16 FRONT LEVEL 2. Remove old Air Conditioner from wall sleeve and prepare wall sleeve as follows: --- Clean interior (do not disturb seals). --- Wall sleeve must be securely fastened in wall before installing Air Conditioner. Drive more nails or screws through sleeve, into wall, if needed. --- Repair paint if needed. 3. If not existing, drill a 1/8 clearance hole for grounding screw through left side of wall sleeve, in a clear area about 3 inches maximum back from front edge of sleeve, using grounding screw and tood washer. Pull loose end of ground wire out front of sleeve, and temporarily bend it down and around lower edge of sleeve.this ground wire will later be attached to frame of air conditioner once it is installed. Wall sleeve to unit sleeve grounding 1 3 Max. 4. Prepare wall sleeve for installation of new unit per following Brand instructions. #1 Emerson 15 Deep #2 Fedders 19 3 /4 Deep #3 Fedders or Friedrich 16 3 /4 Deep #4 General Electric/Hotpoint 16 7 /8/ Deep #5 Sears or Carrier(51S Series) 18 5 /8/ Deep #6 Whirlpool 17 1 /8/ Deep #7 Whirlpool 23 Deep #8 White-Westinghouse/ /2 Deep Frigidaire/Carrier(52F Series) #9 White-Westinghouse/Frigidaire 22 Deep 5. Identify your wall sleeve type and follow instructions for that type in following pages. 1/8 Hole 6

7 IMPORTANT This units increased performance characteristics result from having two rear air intakes. It is very important that se installation instructions are followed so your unit can operate at maximum efficiency. If this is an existing sleeve, and re is an existing rear grille, it needs to be replaced by one that has been shipped with unit in accessory kit. FOR INCREASED EFFICIENCY,UTILIZE THE PROVIDED LOUVERED REAR PANEL Installation of new grille provided with unit 1. Remove existing grille. 2. Place grille included with new air conditioner towards rear of sleeve. 3. Mark through hole positions. 4. Drill through sleeves flanges with a 1/8" drill bit. 5. Attach new grille with self-threading screws and washers. 6. It is VERY IMPORTANT that grille is placed exactly as shown below. 7. Most decorative exterior grilles may be left in place as long as proper interior air direction grille is installed. 7

8 Wall Sleeve Brands: #1 Emerson - 15 Deep 15 Deep 1. Remove existing rear grille as shown on Page 6 1. Remove of this manual existing and rear replace grille with as provided shown louvered on Page 6 of rear this panel. manual Install and as replace shown here. with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of NOTE: existing You sleeve may need to match to drill new holes rear in grille. flange of existing sleeve to match new rear grille Attach(1) 1 x 3/8 x 25 long seal in center at 2. Attach(1)1 top of x sleeve. 3/8 x 25 Remove long seal backing center paper at and top press of into sleeve. position. Remove backing paper 3. and Attach press (2) into 1 position. x 3/8 x 14 long seals to 3. Attach left and right (2) sides 1 x of 3/8 x14 sleeve. long seals to 4. left Cut and (2) 1 right x 3/8 sides x 25 of long sleeve. seals to 14 long,and 4. Cut attach (2) it 1 to x 3/8 vertical x 25 sections long seals of to 14 rear long,and grille attach as shown. it to vertical sections of rear grille 5. as Attach shown. (2) 4-1/2 5. Attach (2)4 1 /2x3 1 x 3-1/2 /2 x1 1 x 1-1/2 centering/support /2 blocks one on each side centering/support wall. Place in center blocks of one on each side wall. Place in center of side side wall with tapered end facing opening. wall with tapered end facing opening Gently Gently slide slide unit unit into into sleeve. sleeve Before sliding all--way back, back, remove remove 2nd 2nd screw from front on on left left side side of of unit. unit. 8. Remove plastic washer from from screw. 9. Screw and attach or end of of ground wire to to unit as as shown in in picture. Make Make sure sure that tood washer is is against against cabinet. cabinet Slide unit unit completely completely to to rear rear to to ensure ensure a a good good seal, seal, making making sure sure ground ground wire wire does does not become tangled. not become tangled. 11.Seal Frame unit as described on page Seal & Frame unit as described on page If you have difficulty with mounting grill to 12. If you sleeve, have difficulty follow with instructions mounting for grill direct to sleeve, mounting follow on Page instructions 16. for direct mounting on Page 16. 8

9 Wall Sleeve Brands: #3 Fedders or Friedrich /4 3 / 4 Deep 1. Remove existing rear grille as shown on Page 6 of 1.Remove this manual existing and replace rear with grille provided as shown louvered on Page rear 6 panel. of this Install manual as and shown replace here. with provided louvered rear panel. Install as shown here. NOTE: you may need to drill holes in flange of NOTE: existing You sleeve may to need match to drill new holes rear grille. in flange of existing sleeve to match new rear grille. 2. Attach(2) 4-1/2 x 3-1/2 x 1-1/2 centering/support blocks one on each side wall. Place in center of side 2. wall Attach(2)4 with 1/ 2 tapered x3 1/ / 2 x1 1/ / end 2 centering/support facing opening. blocks 3. Cut one (2) on 17 each Tapered side wall. Spacer Place Blocks in center as shown of side below wall with into two tapered pieces. end facing opening. 3. Cut (2) 17 Tapered Spacer Blocks as shown below into three pieces. 5 3 /4 17 Tapered Spacer Block The The 2-1/2 2 1 section is placed in in front of of rib rib on on base with base with tapered tapered end facing end facing back of back sleeve. of Cut remaining sleeve. Cut portion to remaining 12 and placed portion behind to 12 1 /2 rib again and placed sloping behind toward rear rib again of sloping sleeve. This toward helps induce rear a rearward of sleeve. slope on This helps unit. induce a 5. Attach rearward (1) 1 slope x 3/8 on x 25 long unit. seal in center at 5. Attach top of (1)1 sleeve. x3/8 Remove x25 long seal backing paper center and press at into top position. of sleeve. Remove backing 6. Attach paper (2) and 1 press x 3/8 x into 14 position. seals to left and right 6. Attach (2) 1 x3/8 x14 seals to left and sides of sleeve. right sides of sleeve. 7. Cut (2) 1 x 3/8 x 25 long seals to 14 long and 7. Cut (2) 1 x3/8 x25 long seals to 14 long attach and attach it to it to vertical vertical sections sections of rear of grille rear as shown. grille as shown Gently slide slide unit unit into into sleeve. sleeve Before sliding all--way back, back, remove remove 2nd screw 2nd from screw front from on left front side on of left unit. side of unit Remove plastic plastic washer washer from from screw. screw Screw and and attach attach or or end end of of ground ground wire to wire unit to as shown unit as in shown picture. in Make picture. sure Make that sure tood that washer tood is against washer is cabinet. against cabinet Slide unit unit completely completely to rear to to ensure rear to a ensure good seal, making a good sure seal, ground making wire sure does not ground become wire tangled. does 13. Seal not & become Frame tangled. unit as described on page If you have difficulty with mounting grill to sleeve, follow instructions for direct mounting on Page Cut Here 12-1/2 2-1/2 Protection Paper Backing

10 Wall Sleeve Brands: #4 General Electric/Hotpoint /8 8 Deep 1. Remove existing rear grille as shown on Page 6 of 1. this Remove manual existing and replace rear grille with provided as shown louvered on Page rear 6 panel. of this Install manual as and shown replace here. with provided louvered rear panel. Install as shown here. NOTE: you may need to drill holes in flange of NOTE: existing You sleeve may need to match to drill new holes rear in grille. flange of existing sleeve to match new rear grille. 2. Cut (2) 17 Tapered Spacer Blocks as shown below into two pieces. 2. Cut (2) 17 Tapered Spacer Blocks as shown below into two pieces /4 Tapered Spacer Block 1 Cut Here 13 Protection Paper Backing 3. Install 13 section as shown with tapered end from 3. Install back 13 section of sleeve. as shown This with helps induce tapered a rearward slope end 1 /2 from on back unit. of sleeve. This helps induce a rearward slop on unit. 4. Attach (1) 1 x 3/8 x 25 long seal in center at 4. Attach (1)1 x3/8 x25 long seal in center top at of top sleeve. of Remove sleeve. Remove backing paper backing and press into paper position. and press into position. 5. Attach 5. Attach (2) 1 (2) x 13/8 x3/8 x 14 x14 seals seals to to left and left right and sides of right sleeve. sides of sleeve. 6. Cut 6. Cut (2) 1 (2) x 13/8 x3/8 x 25 x25 long long seals seals to 14 to long 14 long and attach it to and vertical attach sections it to of vertical rear sections grille as of shown. rear 7. Center grille unit as and shown. gently slide unit into sleeve. 8. Before 7. Center sliding unit all--way and gently back, slide remove unit into 2nd sleeve. screw from 8. Before sliding all--way back, remove 2nd front on left side of unit. screw from front on left side of unit. 9. Remove 9. Remove plastic plastic washer washer from from screw. screw. 10. Screw 10. Screw and attach and attach or or end of end of ground ground wire to unit wire as to shown unit in picture. as shown Make in picture. sure that Make tood sure washer that is against tood cabinet. washer is against cabinet Slide unit completely unit completely to rear to to rear ensure to ensure a good seal, making a good seal, sure making ground sure wire does ground not become wire does tangled. not become tangled. 12. Seal & Frame unit as described on page If you have difficulty with mounting grill to sleeve, follow instructions for direct mounting on Page

11 Wall Sleeve Brands: #5 #5 Sears of or Carrier Carrier 51S 51S Series Series /8 ( / 8 Deep) 1. Remove existing rear grille as shown on Page 6 of this 1. manual Remove and existing replace rear with provided grille as louvered shown on rear Page panel. 6 Install of this as manual shown and here. replace with provided louvered rear panel. Install as shown here. NOTE: you may need to drill holes in flange of existing NOTE: sleeve You to match may need new rear to drill grille. holes in flange of existing sleeve to match new rear grille. 2. Install (2) tapered spacer blocks to floor of sleeve as shown. This helps induce a rearward slope 2. Install on (2) unit. tapered spacer blocks to floor of 3. Install sleeve as shown as shown. with This tapered helps end induce from a back rearward of sleeve. slop This on helps unit. induce a rearward slope on unit Install Attach as (1) shown 1 x 3/8 with x 25 long tapered seal in end 1 /2 center fromat back top of of sleeve. Remove This helps backing induce paper a and rearward press into slop position. on unit Attach (2) (1)1 x x3/8 3/8 x x25 14 seals long to seal in left and center right at sides of top of sleeve. sleeve. Remove backing 6. paper Cut (2) and 1 x press 3/8 x into 25 long position. seals to 14 long and 5. Attach attach it (2) to 1 x3/8 vertical x14 sections seals of to rear left grille and as right shown. sides of sleeve. 6. Cut (2) 1 x3/8 x25 long seals to 14 long 7. Center unit and gently slide unit into sleeve. and attach it to vertical sections of rear 8. grille Before as sliding shown. all--way back, remove 2nd screw 7. Center from front unit on and left gently side of slide unit. unit into sleeve Before Remove sliding plastic all--way washer from back, remove screw. 2nd 10. screw Screw from and attach front on left or side end of of unit. ground wire 9. Remove to unit as plastic shown in washer picture. from Make sure screw. that 10. tood Screw washer and attach is against or cabinet. end of ground 11. Slide wire to unit unit completely as shown to in picture. rear to ensure Make sure a good seal, that making tood sure washer ground is against wire does not cabinet. become 11.Slide tangled. unit completely to rear to ensure 12. Seal & Frame unit as described on page If you have difficulty with mounting grill to sleeve, follow instructions for direct mounting on Page

12 Wall Sleeve Brands: #6 #6 Whirlpool Whirlpool /8 17 Deep 1/ 8 Deep 1. Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear 1. Remove existing rear grille as shown on Page 6 panel. of this Install manual as shown and replace here. with provided louvered rear panel. Install as shown here. NOTE: you may need to drill holes in flange of NOTE: existing You sleeve may to need match to new drill holes rear grille. in flange of existing sleeve to match new rear grille. 2. Cut (2) 17 Tapered Spacer Blocks as shown below into two pieces. 2. Cut (2) 17 Tapered Spacer Blocks as shown below into two pieces /4 Cut Here Tapered Spacer Block 1 13 Protection Paper Backing 3. Install 13 section to floor of sleeve as 3. Install 13 section to floor of sleeve as shown. shown. This This helps helps induce induce a rearward a rearward slope slop on on unit. unit Attach (1) (1)1 1 x 3/8 x3/8 x 25 x25 long long seal seal in in center center at at top top of of sleeve. sleeve. Remove Remove backing backing paper and press paper into and position. press into position Attach (2) (2) 1 1 x 3/8 x3/8 x 14 x14 seals seals to to left left and and right sides right of sides sleeve. of sleeve Cut (2) (2) 1 1 x 3/8 x3/8 x x25 25 long seals seals to to long long and attach and attach it to it to vertical vertical sections sections of rear of grille rear as shown. grille as shown Center Center unit unit and and gently gently slide slide unit unit into into sleeve. sleeve Before Before sliding sliding all--way all--way back, back, remove remove 2nd screw 2nd from screw front from on left front side on of left unit. side of unit. 9. Remove plastic washer from screw. 9. Remove plastic washer from screw. 10. Screw and attach or end of ground 10. Screw wire to and attach unit as shown or end in picture. of ground Make wire sure to that unit as tood shown washer in picture. is against Make sure that cabinet. 11.Slide tood washer unit is completely against to cabinet. rear to ensure 11. Slide a good unit seal, completely making sure to rear ground to ensure wire a does good seal, not making become sure tangled. ground wire does not become 12.Seal tangled. & Frame unit as described on page Seal & Frame unit as described on page If you have difficulty with mounting grill to sleeve, follow instructions for direct mounting on Page

13 Wall Sleeve Brands: #7 Whirlpool #7 Whirlpool - 23 Deep ( 23 Deep) 1. Remove existing rear grille as shown on Page 6 of this 1. manual Remove and existing replace rear with grille provided as shown louvered on Page rear panel. 6 of this Install manual as shown and here. replace NOTE: with You provided may need to drill louvered holes in rear flange panel. of existing Install as sleeve shown to here. match new rear grille. 2. Place NOTE: (2) You 1 x may 1-1/2 need x 14 to drill seals holes against flange each side. of existing sleeve to match new rear grille. 3. Gently slide unit in and check if amount extending from Because sleeve of is sufficient increased once unit depth, trim frame first try is dry fitting using method described below: attached. 2. Place (2) 1 x1 1 /2 x14 seals against each side. 4. If position is Ok, remove unit and proceed to next 3. Gently slide unit in and check if amount extending step. If not from go to step sleeve 9. is sufficient once trim 5. Attach frame (1) 1 is x attached. 1-1/2 x 25 long seal in center at 4. top If position of sleeve. is Ok, remove Remove unit and backing proceed paper toand press into next position. step. If not go to step Attach (1)1 x1 1 /2 6. Attach (2) 1 x 1-1/2 x 14 x25 seals long to seal in left and center right sides at of top sleeve. of sleeve. Remove backing paper and press into position. 7. Cut (2) 1 x 3/8 x Attach (2) 1 x1 1 long seals to 14 long and /2 x14 seals to left and attach right to sides vertical of sections sleeve. of grille as shown. 8. Attach 7. Cut (2) tapered 1 x 3 /8 x25 spacer long blocks seals to to 14 floor long of sleeve. and Now attach go to step vertical 15. Use sections se next of steps grille if as unit shown. requires extra extension into room. 9. Attach 8. Attach 1 x 3/4 tapered x 14 long spacer seal blocks over to solid floor of vertical portion sleeve. of Now go rear to grille. step Attach (2) 4-3/4 x 3-3/4 x 1-3/4 foam blocks with Use se next steps if unit requires extra extension slot overlapping into room. seal above. 11. Install 9. Attach divider 1 x 3 /4 x14 into long slots seal of over foam solid blocks. You vertical may need portion to trim of length rear grille. to size. 10. Attach (2) 4 3 /4 x3 3 /4 x Repeat steps 9-11 for or /4 foam vertical blocks shown with portion slot of overlapping grille as shown seal in above. picture. 13. Attach 11. Install (2) 1 x 1-1/2 divider x 14 into seals slots along of foam sides of blocks. You may need to trim length to size. 12. sleeve Repeat again steps making 9-11 for sure all or seals vertical are flush. shown 14. Cut portion 1 x 1-1/2 of x grille 25 as seal shown to fit in top picture. of sleeve. 13. Attach The pieces (2) 1 must x1 1 /2 x14 be fitted seals flush along to sides edge of divider. of sleeve again making sure all seals are 15. Center flush. unit and gently slide unit into sleeve. 14.Cut 1 x1 1 /2 16. Before sliding all--way x25 seal back, to remove fit top 1st of screw sleeve. The pieces must be fitted flush to from front on left side of unit. edge of divider. 17. Remove 15. Center unit plastic and washer gently from slide unit screw. into sleeve. 18. Screw 16. Before and attach sliding all--way or end back, of remove ground wire 1st to screw unit as from shown front in on picture. left side Make of unit. sure that tood 17. Remove washer is against plastic washer cabinet. from screw. 19. Slide 18. Screw unit and completely attach to or rear end to of ensure ground a good seal, making wire to sure unit as ground shown wire in picture. does not Make become sure tangled. 20. Seal & Frame unit as described on page If you have difficulty with mounting grill to sleeve, follow instructions for direct mounting on Page

14 Wall Sleeve Brands: #8 White Westinghouse/Frigidaire/Carrier 52F Carrier Series 52F - (16 Series /2 ( 16 Deep) /2 Deep) 1. Remove existing rear grille as shown on Page 6 of 1.Remove this manual existing and replace rear with grille provided as shown louvered on Page rear 6 panel. of this Install manual as and shown replace here. with provided louvered rear panel. Install as shown here. NOTE: you may need to drill holes in flange of existing sleeve You may to match need new to drill rear holes grille. in flange of NOTE: existing sleeve to match new rear grille. 2. Attach (1) 1 x 3/8 x 25 long seal in center at top of sleeve. Remove backing paper 2. Attach and press (1)1 into position. x3/8 x25 long seal in center 3. at Attach top (2) of 1 x 3/8 x sleeve. 14 seals Remove to left backing and right paper sides of and press sleeve. into position Attach (2) 1 x x3/8 3/4 x x14 14 long seals seals to vertically left and 4.5 right from sides left of side of sleeve. sleeve.attach or 4. Attach 1 x 3/4 (2) x 114 x3/4 long x14 seal 4 long from seals right vertically side of 4.5 from sleeve. left side of sleeve.attach or 5. 1 Center x3/4 unit x14 and long gently seal slide 4 from unit into right sleeve. side of 6. sleeve. Before sliding all--way back, remove 2nd screw 5. Center from front unit on and left gently side of slide unit. unit into sleeve Before Remove sliding plastic all--way washer back, from remove screw. 2nd screw from front on left side of unit. 8. Screw and attach or end of ground wire 7. Remove plastic washer from screw. 8. Screw to unit and as attach shown in or picture. end Make of sure ground that wire tood washer unit is as against shown in picture. cabinet. Make sure 9. that Slide tood unit completely washer to is against rear to ensure cabinet. a 9. Slide good seal, unit making completely sure to ground rear wire to does ensure not become a good tangled. seal, making sure ground wire does 10. Seal & Frame unit as described on page If you have difficulty with mounting grill to sleeve, follow instructions for direct mounting on Page

15 eat Controller Room Air Conditioner with R-410A Owner s Manual Wall Sleeve Brands: #9 White #9 White Westinghouse Westinghouse or Frigidaire or Frigidaire - (22 Deep) ( 22 Deep) 1. Remove 1. Remove existing existing rear grille rear as grille shown as on shown Page on 6 of Page this 6 of this manual and replace with provided manual and replace with provided louvered rear panel. louvered rear panel. Install as shown here. Install as shown here. NOTE: You may need to drill holes in flange NOTE: of You existing may need sleeve to drill to match holes new in flange rear of grille. existing sleeve Because to match of new increased rear grille. unit depth, first try Because dry fitting of using increased method unit depth, described first try below: dry fitting 2. Place using (2) 1 method x1 1 /2 x14 described seals against below: each side. 3. Gently slide unit in and check if amount extending (2) 1 from x 1-1/2 sleeve x 14 seals is sufficient against once each side. trim 2. Place 3. Gently frame slide unit is attached. in and check if amount extending from 4. If position is Ok, remove unit and proceed to sleeve is sufficient once trim frame is attached. next step. If not go to step If position 5. Attach is Ok, (1)1 remove x1 1 unit x15 and long proceed seal to to left next /2 and step. right If not sides go to of step 8. sleeve. 5. Attach 6. Cut (1) (1) 1 x 11-1/2 x1 1 x x25 15 long seal to to 14 long left and and right sides attach of sleeve. it vertically to rear grill 4.5 from 6. Cut (1) 1 left x 1-1/2 side,repeat x 25 long and seal attach to 14 4 long from and right attach it vertically side. to rear grill 4.5 from left side,repeat 7. Attach(1) 1 x1 1 /2 and attach 4 from right x25 side. long seal in center at 7. Attach(1) top 1 x of 1-1/2 sleeve.remove x 25 long seal in backing center at paper and press into position.proceed to step 14. top of sleeve. Remove backing paper and press Use se next steps if unit requires extra into extension position. Proceed into to room. step 14. Use se next steps if 8. unit Attach requires 1 x 3 /4 extra x14 extension long seal into over room. solid 8. Attach vertical 1 x 3/4 portion x 14 long of seal rear over grille. solid vertical portion 9. Attach of (2) rear 4 3 /4grille. x3 3 x1 3 /4 foam blocks with 9. Attach slot (2) overlapping 4-3/4 x 3-3/4 x seal 1-3/4 above. foam blocks with slot 10. overlapping Install divider seal above. into slots of foam 10. Install blocks. divider You into may need slots to of trim foam length blocks. to size. You 11. Repeat steps 8-10 for or vertical shown may need to trim length to size. portion of grille as shown in picture. 11. Repeat 12. Attach steps 8-10 (2) 1 for x1 1 /2 x14 or seals vertical along shown sides portion of of sleeve grille as again shown making sure picture. all seals are 12. Attach flush. (2) 1 x 1-1/2 x 14 seals along sides of sleeve 13.Cut again making 1 x1 1 /2 sure x25 all seals to are fit flush. top of 13. Cut sleeve. 1 x 1-1/2 The x pieces 25 seal must to fit be fitted top flush of to sleeve. The pieces edge must of be divider. fitted flush to edge of divider. 14. Center 14. Center unit and unit gently and slide gently unit slide into unit sleeve. into sleeve. 15. Before 15. Before sliding sliding all--way all--way back, remove back, 1st remove screw 1st from screw from front on left side of unit. front on left side of unit. 16. Remove plastic washer from screw. 16. Remove 17. Screw plastic and attach washer from or end screw. of ground 17. Screw wire and to attach unit or as shown end of in picture. ground Make wire sure to unit that as shown tood in picture. washer Make is against sure that cabinet. tood washer 18.Slide is against unit completely cabinet. to rear to ensure 18. Slide a good unit completely seal, making to sure rear to ground ensure wire a good does seal, making not become sure tangled. ground wire does not become tangled. 19.Seal & Frame unit as described on page If you have difficulty with mounting grill to 19. Seal & Frame unit as described on page 17. sleeve, follow instructions for direct 20. If you have difficulty with mounting grill to sleeve, mounting on Page 16. follow instructions for direct mounting on Page

16 Direct Unit Mounting: The previous directions are preferable way to mount new rear grill. The units performance is slightly better and possibility of drafts is reduced. As a last resort, direct mounting of grille to unit can be considered. Note: The grille must be installed prior to inserting unit into sleeve. 1. Attach 2 seal pieces (1 X3/8 X14 ) as shown in Fig Position grille over rear of unit making sure that: a. The double set of screw holes are at bottom. b. The fins of grill are pointed away from unit. 3. Align top of grille with top of unit. The overhang on each side is equal. 4. If unit has not been pre-drilled (some models), carefully drill 4-1/8 holes through grille and into side flange of unit approximately 1 1 /2 to 2 from top and bottom as in Fig. 2, 3. (Be careful not to drill into copper heat exchanger coils.) 5. Install 4 - #8 self tapping screws to affix grille to unit. 6. Insert unit into sleeve

17 FINISHING INSTALLATION: 1. Install 1 x1 1 /2 x84 long stuffer-seal between wall-sleeve and unit. A flat-bladed screwdriver or putty knife is recommended. 2. Assemble trim frame by inserting top and bottom pieces into side pieces and snapping into place. 3. Pull cord through trim frame n slide over unit until flush with wall. 17

18 NORMAL SOUNDS High Pitched Chatter High efficiency compressors may have a high pitched chatter during cooling cycle. Vibration Unit may vibrate and make noise because of poor wall or window construction or incorrect installation. Sound of Rushing Air At front of unit, you may hear sound of rushing air being moved by fan Pinging or Swishing Droplets of water hitting condenser during normal operation may cause pinging or swishing sounds. Gurgle/Hiss Gurgling or hissing noise may be heard due to refrigerant passing through evaporator during normal operation. NOTE: All illustrations in this manual are for explanation purposes only. Your air conditioner may be slightly different. The actual shape and design shall prevail. AIR CONDITIONER FEATURES ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with control panel as shown below and all its functions, n follow symbol for functions you desire. The unit can be controlled by unit control alone or with remote. Auto Cool Dry Heat Energy Saver Mode Fan TEMP/TIMER TEMP/TIMER On Timer Off Sleep Fan Check Filter Follow Me Auto Low Med High REMOTE SIGNAL RECEPTOR TO TURN UNIT ON OR OFF: Press ON/OFF button to turn unit on or off. NOTE: The unit will initiate automatically Energy Saver function under Cool, Dry, Auto (only Auto-Cooling and Auto-Fan) modes. (Electric Heating Models) Auto Cool Dry Energy Saver Mode Fan TEMP/TIMER TEMP/TIMER On Timer Off Sleep Fan (Cooling Only Models) Check Filter Follow Me Auto Low Med High TO CHANGE TEMPERATURE SETTING: Press / UP/DOWN button to change temperature setting. NOTE:Press or hold eir UP( ) or DOWN ( ) button until desired temperature is seen on display. This temperature will be automatically maintained O O O O anywhere between 62 F(17 C) and 86 F(30 C). If you want display to read actual room temperature, see To Operate on Fan Only section. 18

19 AIR CONDITIONER FEATURES TO ADJUST FAN SPEEDS: Press to select Fan Speed in four steps-auto, Low, Med or High. Each time button is pressed, fan speed mode is shifted.for some models, fan speed can not be adjusted under HEAT mode. On Dry mode, fan speed is controlled at Low automatically. SLEEP FEATURE: Press Sleep button to initiate sleep mode. In this mode selected temperature will increase O O (cooling) or decrease (heating) by 2 F/1(or 2) C 30 minutes after mode is selected.the t emperature will n increase (cooling) or decrease (heating) by O O anor 2 F/1(or 2) C after an additional 30 minutes. This new t emperature will be maintained f or 6 h ours before i tr eturns to th eoriginallyse lectedtemperature. This ends Sleep mode and unit will continue to operate as originally programmed. The Sleep mode program can be cancelled at any time during operation by pressing Sleep button again. CHECK FILTER FEATURE: Press Check filter button to initiate is feature. This feature is a reminder to clean Air Filter for more efficient operation. The LED(light) will illuminate after 250 hours of operation. To reset after cleaning filter, press Check Filter button and light will go off. ENERGY SAVER FEATURE: Press Energy saver button to initiate this function. This function is available on COOL, DRY, AUTO (only AUTO-COOLING and AUTO-FAN) modes.the fan will continue to run for 3 minutes after compressor shuts off.the fan n cycles on for 2 minutes at 10 minute intervals until room temperature is above set temperature, at which time compressor turns back on and Cooling Starts. FOLLOW ME FEATURE:(on some models) Follow Me Light flashing This feature can be activated from remote control ONLY. The remote control serves as a remote rmostat allowing for precise temperature control at its location. To activate Follow Me feature, point remote control towards unit and press Follow Me button. The remote display is actual temperature at its location. The remote control will send this signal to air conditioner every 3 minutes interval until press Follow Me button again. If unit does not receive Follow Me signal during any 7 minutes interval, unit will beep to indicate Follow Me mode has ended. TO SELECT THE OPERATING MODE: To choose operating mode, press Mode button.each time you press button, a mode is selected in a sequence that goes from Auto, Cool, Dry,heat(cooling only models without)and Fan. The indicator light beside will be illuminated and remained on once mode is selected. The unit will initiate automatically Energy Saver function under Cool, Dry, Auto(only Auto-Cooling and Auto-Fan) modes. To operate on Auto feature: When you set air conditioner in AUTO mode, it will automatically select cooling, heating(cooling only models without), or fan only operation depending on what temperature you have selected and room temperature. The air conditioner will control room temperature automatically round temperature point set by you. In this mode, fan speed cannot be adjusted, it starts automatically at a speed according to room temperature. To operate on Fan Only: Use this function only when cooling is not desired,such as for room air circulation or to exhaust stale air(on some models). (Remember to open vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. During this function, display will show actual room temperature, not set temperature as in cooling mode. In Fan only mode, temperature is not adjusted. To operate on Dry mode: In this mode, air conditioner will generally operate in form of a dehumidifier. Since conditioned space is a closed or sealed area, some degree of cooling will continue. TIMER: AUTO START/STOP FEATURE: When unit is on or off, first press Timer button, TIMER ON indicator light illuminates. It indicates Auto Start program is initiated. When time of TIMER ON is displayed,press Timer button again, TIMER OFF indicator light illuminates. It indicates Auto Stop program is initiated. Press or hold UP or DOWN button to change Auto time by 0.5 hour increments, up to 10 hours,n at 1 hour increments up to 24 hours.the control will count down time remaining until start. The selected time will register in 5 seconds, and system will automatically revert back to display previous temperature setting or room temperature when unit is on.(when unit is off,re is no display.) Turning unit ON or OFF at any time or adjusting timer setting to 0.0 will cancel Auto Start/Stop timed program. 19

20 AIR CONDITIONER FEATURES DISPLAYS: DISPLAYS: Displays O O Shows set temperature in C or F and Auto-timer settings.while on Fan only mode,it shows room temperature. Error codes: AS-Room temperature sensor error-unplug unit and plug it back in.if error repeats, call for service. NOTE:In Fan only mode,it will display LO or HI. -Evaporator temperature sensor error-unplug unit and plug it back in.if error repeats, call for service. NOTE: is displayed as shown in left picture. HS -Electric heating sensor error-unplug unit and plug it back in.if error repeats, call for service. NOTE: If unit shuts off unexpectedly due to power cut, it will restart with previous function setting automatically when power resumes. ADDITIONAL THINGS YOU SHOULD KNOW Now that you have mastered operating procedure, here are more features in your control that you should become familiar with. The Cool circuit has an automatic 3 minute time delayed start if unit is turned off and on quickly. This prevents overheating of compressor and possible circuit breaker tripping.the fan will continue to run during this time. The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. To convert from one to or, press and hold Left and Right Temp/Timer buttons at same time, for 3 seconds. Air Directional Louvers Air Directional Louvers Louvers Center handles Air Direction(4- way) Air directional louvers control air flow direction.your air conditioner has 4-way directional system described below.the louvers will allow you to direct air flow Up or Horizontal, and Left or Right throughout room as needed.use center handles to adjust air directional louvers side-to-side until desired Left or Right direction is obtained.pivot horizontal louvers with your fingertips until desired Up or Horizontal direction is obtained.there are a total of 4 possible air directional orientations available with this system. CARE AND CLEANING Air Filter Cleaning CAUTION Clean your air conditioner occasionally to keep it looking new. Be sure to unplug unit before cleaning to prevent shock or fire hazards. The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in filter can build up and cause an accumulation of frost on cooling coils. 20

21 CARE AND CLEANING Air Filter Cleaning Take filter by center and pull up and out. Wash filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly. Gently shake excess water from filter. Be sure filter is thoroughly dry before replacing. Or, instead of washing you may vacuum filter clean. Note: Never use hot water over 40 C(104 F) to cl ean th e a i r fil ter. Never attempt to operate unit without air filter. Winter Storage If you plan to store air conditioner during winter, remove it carefully from window according to installation instructions. Cover it with plastic or return it to original carton. Energy Saving Note: In order to reach maximum energy saving and comfort, it is recommended to use a cover to insulate unit when unit is not in use. The recommended size for unit is 24.4 x14.8 x2.2 (WxHxD). Cabinet Cleaning Be sure to unplug air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry. Never use harsh cleaners, wax or polish on cabinet front. Be sure to wring excess water from cloth before wiping around controls. Excess water in or around controls may cause damage to air conditioner. Plug in air conditioner. TROUBLESHOOTING TIPS Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not result of defective workman-ship or materials in this appliance. Problem Air conditioner does not start Solution Wall plug disconnected. Push plug firmly into wall outlet. House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker. Plug Current Device Tripped. Press RESET button. Power is OFF. Turn power ON. Air from unit does not feel cold enough O O Room temperature below 62 F(17 C ). Cooling may not occur until room temperature O O rises above 62 F(17 C). Temperature sensing behind air filter element touching cold coil. Keep it from cold coil. Set to a Lower temperature. Compressor stopped when changing modes. Wait for 3 minutes after set to COOL mode. Air conditioner cooling, but room is too warm- ice forming on cooling coil behind decorative front. O O Outdoor temperature below 64 F(18 C). To defrost coil, set FAN ONLY mode. Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY mode. Thermostat set too cold for night-time cooling. To defrost coil, set to FAN ONLY mode. Then, set temperature to a Higher setting. 21

22 TROUBLESHOOTING TIPS Problem Air conditioner cooling, but room is too warm- NO ice forming on cooling coil behind decorative front. Solution Dirty air filter- air restricted. Clean air filter. Refer to Care and Cleaning section. Temperature is set too High, set temperature to a Lower setting. Air directional louvers positioned improperly. Position louvers for better air distribution. Front of units is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in front of unit. Doors, windows, registers, etc. Open- cold air escapes. Close doors, windows, registers. Unit recently turned on in hot room. Allow additional time to remove Stored heat from walls, ceiling, floor and furniture. Air conditioner turns on and off rapidly Noise when unit is cooling Water dripping INSIDE when unit is cooling. Water dripping OUTSIDE when unit is cooling. Remote Sensing Deactivating Prematurely (some models) Room too cold Dirty air filter- air restricted. Clean air filter. Outside temperature extremely hot. Set FAN speed to a Higher setting to speed up airflow. Air movement sound. This is normal. If too loud, set to a slower FAN setting. Window vibration - poor installation. Refer to installation instructions or check with installer. Improper installation. Tilt air conditioner slightly to outside to allow water drainage. Refer to installation instructions - check with installer. Unit removing large quantity of moisture from humid room. This is normal during excessively humid days. Remote control not located within range. Place remote control within 20 feet & 180, radius of front of unit. Remote control signal obstructed. Remove obstruction. Set temperature too low. Increase set temperature. 22