K&W Permanent Metallic Block Seal
|
|
- Julie Heath
- 5 years ago
- Views:
Transcription
1 K&W Permanent Metallic Block Seal Block and Radiator Seal Permanently seals small holes and cracks, repairing: Engine blocks Cylinder heads Radiators Heater cores Cooling passages Head gaskets Water Jackets
2 K&W Permanent Metallic Block Seal Block Seal seeks out cracks or small holes in the engine block, radiator, head gasket, freeze plugs and heater core.
3 K&W Permanent Metallic Block Seal Once the crack or hole is located, Block Seal, mixed with water, is forced in from the pressure of the cooling system. Block Seal is hardened as oxygen passes over the crack forming a permanent molecular bond that s as strong as steel.
4 K&W Permanent Metallic Block Seal How to Use: Example: 1985 Ford Fairmont 3.8L V-6 136K Miles The Problem Internal coolant leak Diagnosis Cracked head gasket Mechanic s Estimates $ $ 1,400 Alternate Repair Method Treat with K&W Block Seal
5 K&W Permanent Metallic Block Seal Preparation Park vehicle in a spot where it can sit for at least 24 hours. Products needed: Block Seal, Radiator Flush and Radiator Anti-Rust. Other products & tools required: Antifreeze, drain pan and basic hand tools.
6 Drain antifreeze into drain pan Block Seal Step 1 Block Seal cannot be added to coolant because it will solidify. Tip: If you plan on reusing current antifreeze, drain into a clean pan. It is suggested that you use new antifreeze.
7 Block Seal Step 2 Flush cooling system Why? To remove scale, rust and corrosion. This will aid the sealing process and clean the cooling system. Tip: Using a back-flush kit is the most effective method of flushing.
8 Block Seal Step 2 (repeat) Flush, Flush, Flush! This may be the most important step. Flush the cooling system until the water is clear and there is no antifreeze present. Turn on the heater and defroster while vehicle is running. This will ensure that the thermostat is open resulting in faster warm-up time. If possible, remove the thermostat and replace after leak has been repaired. Tip: If you are experiencing an internal coolant leak (compression leak), remove and check spark plugs for corrosion or fluid appearance. You may also run a compression test. Upon determining the affected cylinder(s) remove the spark plug and disable the fuel injection before the next step.
9 Mix Block Seal with water In a separate container, mix entire can of Block Seal with 3 quarts of clean warm tap water. Shake/mix the solution before adding to the empty cooling system. (Can may be pressurized, hold away from face when opening) Use a clean plastic milk jug or other container to mix Block Seal and water. Block Seal Step 3
10 Block Seal Step 4 Add Block Seal mixture Pour entire Block Seal mixture into cooling system. Immediately start the vehicle, top-off with water, replace the radiator cap and let the vehicle idle for a minimum of 20 to 30 minutes. If vehicle overheats, turn off vehicle and let temperature return to normal before restarting for remaining time frame. Tip: If the thermostat has not been removed, turning on the heat and defrost will ensure the thermostat opens
11 Block Seal Step 5 Let vehicle cool After vehicle is cool, remove radiator cap and drain cooling system Tip: There is not a specific time frame for cooling. You may drain cooling system when you feel comfortable removing the fluid.
12 Block Seal Step 6 Drain and Cure Remove radiator cap and open all drain cocks to allow air to circulate in the cooling system. Removing the lower radiator hose will help in allowing more air into the coolant system Let empty cooling system dry for a minimum of 24 hours. Tip: Block Seal needs air to cure and form a permanent bond, the longer it can dry the better the adhesion.
13 Block Seal Step 7 Flush and Add coolant After drying time has elapsed, flush coolant system until clear and fill with a 50/50 mix of antifreeze & water (You may add anti-rust or other additives if desired). Let vehicle idle until hot. The leak has been repaired. Reinstall thermostat if it was removed during the process. Change oil and filter if oil is contaminated. A engine oil flush is recommended if the oil is extremely dirty. Check coolant level frequently over the next 100 miles.
14 LEAK REPAIRED! Cost Retail K&W Block Seal $6.69 CRC Radiator Flush $1.99 Antifreeze (x2) $9.98 CRC Anti-Rust $1.99 Drain Pan $4.99 Total $25.64 Results Estimate to repair vehicle $ 800 to $ 1,400 SAVINGS $ 774 TO $ 1,374!!!!
15 Block Seal Competitors Most brands use wood flour dust to form a soft, temporary seal. While the coolant - filled with wood pulp - is under pressure, the pulp seals the crack. But what happens when you change your coolant? K&W Block Seal does not rely on cooling system pressure to maintain a seal. It actually repairs cracks and small holes in your system.
16 Gunk vs. Block Seal Poured Equal Amounts 36 Hours Later! Results Gunk not dry within 24 hours Gunk carrier solution evaporates left with little bonding material Gunk dries unevenly and becomes brittle Block Seal 100% dry in 24 hours Block Seal maintains original mass left with solid bonding material Block Seal dries smooth and strong
SECTION 1D ENGINE COOLING
SECTION 1D ENGINE COOLING CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More information02 COOLING SYSTEM 02 COOLING SYSTEM COOLING SYSTEM INDEX. 1. General Specifications... 65
REV. 02 / 01.11.13 COOLING SYSTEM INDE 1. General... 64 2. Specifications... 65 3. Structure and Operation... 65 3.1. Cooling System... 65 3.2. Radiator... 65 3.3. Water Pump... 65 3.4. Thermostat... 65
More information6. COOLING SYSTEM 6-0 COOLING SYSTEM MXU 500
6 COOLING SYSTEM SYSTEM FLOW PATTERN----------------------------------------------- 6-1 SERVICE INFORMATION------------------------------------------------ 6-2 TROUBLESHOOTING-----------------------------------------------------
More informationUNIT 5 COOLING SYSTEMS OF IC ENGINES
UNIT 5 COOLING SYSTEMS OF IC ENGINES Cooling Systems of IC Engines Structure 5.1 Introduction Objectives 5.2 Air Cooling System 5.3 Water Cooling System 5.3.1 Components of Water Cooling System 5.3.2 Advantages
More informationModern Auto Tech Study Guide Chapters 39 & 40 Pages Cooling Systems 43 Points. Automotive Service
Modern Auto Tech Study Guide Chapters 39 & 40 Pages 725 767 Cooling Systems 43 Points 1. The cooling system must control the temperature of the engine for low emissions and maximum efficiency. This will
More information1 of 8 5/11/17, 10:01 AM
1 of 8 5/11/17, 10:01 AM Draining and Filling Cooling System (GE 47716) Tools Required * J 26568 Coolant and Battery Fluid Tester * J 42401 Radiator Cap and Surge Tank Test Adapter * GE-47716 Vac N Fill
More informationMishimoto Performance Aluminum Mustang Radiator - Automatic - (97-04 GT/Cobra/MACH1/Bullitt) - Installation Instructions
Mishimoto Performance Aluminum Mustang Radiator - Automatic - (97-04 GT/Cobra/MACH1/Bullitt) - Installation Instructions The below installation instructions work for the following products: Mishimoto Performance
More informationAir Cooled Engine Technology. Roth 9 th Ch 11 Cooling Systems Pages
Roth 9 th Ch 11 Cooling Systems Pages 197 205 1. The and span of an engine depend on how well it is. Efficiency, Life, Cooled Efficiency, Life, Stored Efficiency, Life, Manufactured 2. The average temperature
More informationSAAB 99 Series H Type Engine. Installation Guide Silicone Cooling System Hoses. Classic Silicone Hoses
SAAB 99 Series 1981 1984 H Type Engine Installation Guide Silicone Cooling System Hoses Classic Silicone Hoses http://www.classicsiliconehoses.com/ Disclaimer This document is for reference purposes only.
More informationCOOLING SYSTEM 1. Section V CONTENTS DATA AND SPECIFICATIONS. Page. Fluid Fan Drive (Silent Flite) 3. Water Pump 4. Radiator 5
Section V COOLING SYSTEM CONTENTS Fluid Fan Drive (Silent Flite) 3 Water Pump 4 Radiator 5 Water Temperature Gauge 6 Thermostat 7 Radiator Pressure Cap 7 Service Diagnosis 7 DATA AND SPECIFICATIONS COOLING
More informationEvans Waterless Engine Coolant. General Installation Instructions.
Evans Waterless Engine Coolant General Installation Instructions www.evanscoolants.com.au General Installation Instructions Due to the variety of equipment and cooling system configurations, only generic
More informationChapter 39 Cooling System Fundamentals Test
TERRY FOX AUTOMOTIVE Chapter 39 Cooling System Fundamentals Test When you are done this test guess what you think you will receive for a mark below. If you are within 2 of your actual score you will receive
More information6. Cooling System XCITING 400i. This chapter covers the location and servicing of the cooling system components for the KYMCO XCITING 400i.
6. Cooling System XCITING 400i Cooling System This chapter covers the location and servicing of the cooling system components for the KYMCO XCITING 400i. Coolant... 6-3~6-11 Radiator... 6-12~6-23 Thermostat...
More informationBMW E36 Thermostat Removal And Coolant Flush
BMW E36 Thermostat Removal And Coolant Flush Disclaimer: The cooling system is critical to the proper operation of your car. Failure to properly install all of the components of the cooling system could
More informationEmissions testing Honda Accord/Prelude
Emissions testing Honda Accord/Prelude 1984-1995 PVC TESTING See Figure 4 The PCV valve is easily checked with the engine running at normal idle speed (warmed up). Gently pinch the hose shut, then release
More informationGftOUP 7 COOLING SYSTEM DATA AND SPECIFICATIONS
COOLING SYSTEM 7-1 GftOUP 7 COOLING SYSTEM CONTENTS Page Data and Specifications. 1 Engine Water Temperature Gauge. 8 Pressure Testing Cooling System 8 Radiator. 5 Radiator Pressure Cap 7 Reverse Flushing
More informationPlease take time to carefully read through these guidelines before using your Kamco pump.
The Kamco CLEARFLOW CF90 : QUANTUM pump is a purpose built unit for Power Flushing central heating systems, designed to cure circulation and boiler noise problems caused by the accumulation of sludge,
More informationGROUP 7 COOLING SYSTEM CONTENTS. Page SPECIFICATIONS
COOUNG SYSTEM 7-J GROUP 7 COOLING SYSTEM CONTENTS Page Specifications (Cooling)... 1 Special Tools 2 Torque Reference 2 Specifications (Accessory Belt Drives) 2 Fluid Fan Drive..... 3 Water Punrip..........
More informationPANDORA HEAT BANKS OXFORD BROOKES, HARCOURT HILL. Operation and Maintenance. THERMAL INTEGRATION LTD. Tel: Internet:
PANDORA HEAT BANKS OXFORD BROOKES, HARCOURT HILL Operation and Maintenance THERMAL INTEGRATION LTD. Tel: 0845 2411441 Internet: www.heatweb.com Introduction The District Pandora Heat Bank provides hot
More informationGroup 7 COOLING SYSTEM CONTENTS
Group 7 COOLING SYSTEM CONTENTS COOLING SYSTEM 1 Paragraph Page Engine Water Temperature Gauge 9 7 Instrument Panel Unit 7 Temperature Sending Unit ; 8 Electrical Circuit (Testing) 8 Pressure Testing Cooling
More informationThermo 230 / 231 / 300 / 301 / Troubleshooting
Thermo 230 / 231 / 300 / 301 / 350 5 Troubleshooting 5 Troubleshooting 5.1 General This section describes troubleshooting procedures for the heaters Thermo 230, 231, 300, 301 and 350. CAUTION Troubleshooting
More informationCPC-180-ABNAB. 180 litres, 535mm x 1550mm high
6 8 9 10 1 3 7 2 4 11 13 17 5 28 21 20 19 18 30 Wiring Pandora Heat Bank. 100kW Plate Heat Exchanger with 22mm Thermostatic Mixing Valve. Indirectly Heated. Cylinder Thermostat. Manually Filled store -
More informationAuto Service Test Review. For the Most Effective Personal Review, Match the Following Questions to the On Line Study Guide Multimedia
Auto Service Test Review For the Most Effective Personal Review, Match the Following Questions to the On Line Study Guide Multimedia Auto Service Test Review Test #3 73 Questions from: Chapters 39 & 40
More informationHeaters and Defrosters
Heaters and Defrosters Table of Contents Sub-Headings Safety 2 Warnings 2 Cautions 2 s 2 Introduction 2 General Specifications 2 ISB Engine 2 Coolant Specification 3 Description of Operation 3 Heater Access
More informationHeater Inspection Guidelines
www.hotstart.com Heater Inspection Guidelines INSTRUCTIONAL VIDEO PROVIDING ADDITIONAL SUPPORT CAN BE FOUND AT http://hotstart.com/home/resources/installation-instructions/ HOTSTART heaters utilize a standard
More informationPlease take time to carefully read through these guidelines before using your Kamco pump.
The Kamco CLEARFLOW CF30 CLASSIC pump is a purpose built unit for Power Flushing central heating systems, designed to cure circulation and boiler noise problems caused by the accumulation of sludge, corrosion
More informationWaterless Engine Coolants. General Installation Instructions
Waterless Engine Coolants General Installation Instructions General Installation Instructions 19Jan2015 Due to the variety of equipment and cooling system configurations, only generic installation procedures
More informationCOOLING SYSTEM. Page CO-2 TROUBLESHOOTING... CO-4 CHECK AND REPLACEMEANT OF ENGINE COOLANT... WATER PUMP... DESCRIPTION...
COOLING SYSTEM DESCRIPTION... Page CO-2 TROUBLESHOOTING... CO-4 CHECK AND REPLACEMEANT OF ENGINE COOLANT... WATER PUMP... CO-5 CO-6 THERMOSTAT... CO-8 RADIATOR... CO-9 CO-2 COOLING SYSTEM - Description
More informationPlease take time to carefully read through these guidelines before using your Kamco pump.
The Kamco CLEARFLOW CF190 / CF230 DDV pumps are purpose built units for Power Flushing central heating systems, designed to cure circulation and boiler noise problems caused by the accumulation of sludge,
More informationHEATING AND AIR CONDITIONING
PL HEATING AND AIR CONDITIONING 24-1 HEATING AND AIR CONDITIONING TABLE OF CONTENTS page REMOVAL AND INSTALLATION EVAPORATOR CORE R. H. D....1 HEATERCORE R.H.D...3 page SPECIFICATIONS TORQUE SPECIFICATIONS...6
More informationService Bulletin
Service Bulletin 14-063 November 20, 2014 ATB 00239-01113 REV1 (1411) Low Heat From the Driver s-side Vent Supersedes 14-063, dated November 1, 2014, to revise the information highlighted in yellow. AFFECTED
More informationDo not open the cooling system while it is hot or while the engine is running.
Engine And Radiator 2003 Mazda B2300 2.3L Eng VIN D Base Print Date: 1/4/2019 WARNING: Do not open the cooling system while it is hot or while the engine is running. 1. Drain the cooling system. See ENGINE
More informationI had to remove front splash shield to drain the radiator.
At the start of 2013, my cooling was losing significant coolant that seemed to be coming from the water pump. The car had about 107,000 miles on it at the time. I had to remove front splash shield to drain
More informationSERVICE PROCEDURES. SERVICE TYPE: JPMC Winterization ACCESS: See Order Instructions for Lockbox Code SCHEDULING PROCEDURES: ON-SITE PROCEDURES:
SERVICE PROCEDURES SERVICE TYPE: JPMC Winterization ACCESS: See Order Instructions for Lockbox Code SCHEDULING PROCEDURES: Contact NVMS immediately if you cannot complete and report this order by the due
More informationUser s Information Manual
User s Information Manual Gas-fired water boilers Series 4 Featuring Flexibility Series 4 If the information in this manual is not followed exactly, a fire or explosion may result, causing property damage,
More informationWATER PUMP REQUESTED INFORMATION STANDARD PROCEDURE RAM Pickup 6.7L Eng 2500 STANDARD PROCEDURE - COOLANT AIR EVACUATION
WATER PUMP 2012 RAM Pickup 6.7L Eng 2500 REQUESTED INFORMATION STANDARD PROCEDURE STANDARD PROCEDURE - COOLANT AIR EVACUATION Fig 1: Pressurized Air Operated Vacuum Generator Evacuating or purging air
More informationUser s Information Manual
User s Information Manual CONDENSING GAS BOILER 220/299/300/399 If the information in this manual is not followed exactly, a fire or explosion may result, causing property damage, personal injury or loss
More informationHeating and ventilation system,
Page 1 of 24 87-151 Heating and ventilation system, servicing Instrument panel air outlets and air guide ducts CAUTION! Before working on the electrical system: Obtain security code for anti-theft radio.
More informationMyths, Lies and Truths about Asphalt Patching Machines
BEFORE YOU PURCHASE YOUR ASPHALT PATCHING MACHINE READ THIS!!! Myths, Lies and Truths about Asphalt Patching Machines MYTH: Radiant air heated machines use less energy than heat transfer oil heated machines.
More informationinstallation & operating instructions
installation & operating instructions RGE 410 RA/RM-2D 822706106 MO-M 0740 INTRODUCTION We are pleased that you have chosen this refrigerator and hope you will derive much satisfaction from using it.
More informationInstallation Instructions
Suzuki Samurai Coolant and Water Hose Kit (SKU# SER-CHK) Installation Instructions SER-HHCK SER-WPI SER-ROP CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools
More informationINSTALLATION PROCEDURE MACK E7
Evans Cooling Systems, Inc. 255 Gay Street Sharon, CT 06069 860-364-5130 INSTALLATION PROCEDURE MACK E7 Installing Evans waterless Heavy Duty Coolant and a ResistorPac VER 02Feb2012 CAUTIONARY NOTE: DO
More informationUser s Information Manual
Gas-fired Water boiler Series 2 NOTICE: Series 1/Series 2 identification Read the boiler rating plate to determine the series number. The rating plate is located on the right side of the boiler. User s
More informationMODEL A18 SOLVENT RECOVERY SYSTEMS (EXPLOSION PROOF UNITS)
MODEL A18 SOLVENT RECOVERY SYSTEMS (EXPLOSION PROOF UNITS) FOR PROPER AND SAFE USE OF THIS CHEMCHAMP EQUIPMENT, PLEASE FOLLOW THIS DOCUMENT AND LOCAL AUTHORITY. KEEP THIS DOCUMENT FOR FUTURE REFERENCE.
More informationEngine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets
TT 880 INSTRUCTIONS 7/92 Engine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets Model Voltage Kit No. All Models 120 276380 All Models 240 276381 This
More informationRadiator Additive. ZetaLube. Description
TM A New Lubricity Dimension Evolved From Experience www.magnagroup.com Description Magna Industrial reserves the right to modify or change this product for purpose of improving its performance characteristics
More informationJOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30)
P. 1 of 12 JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30) Item: Qty: Description: 1 2 1 x 1 x 5/8 Tee Fitting 2 2 Plastic Snap-in Hose Grommet 3 4 1-1/2" Hose Clamps
More informationPANCRETE PAN IN A CAN
PANCRETE PAN IN A CAN Lakeshore Environmental Contractors, LLC 5513 Eastcliff Industrial Loop Birmingham, AL 35210-5418 Office 205-943-5711 Fax 205-943-8317 Web www.lecbiz.com STANDING WATER After a few
More informationUM120W OPERATING MANUAL MANUAL WATERBORNE GUN CLEANER CAUTION FOR WATERBORNE PAINTS ONLY UNI-RAM CORPORATION ONTARIO CANADA
OPERATING MANUAL MANUAL WATERBORNE GUN CLEANER UM120W CAUTION FOR WATERBORNE PAINTS ONLY THIS UNIT IS NOT DESIGNED FOR USE WITH SOLVENT BASED PAINT UNI-RAM CORPORATION ONTARIO CANADA Revised 2009-03 CONTENTS
More informationEngine Cooling Pulsator
Engine Cooling Pulsator ENGINE COOLING SYSTEM FLUSHER U.S. Patent No. 5615695 Perfect for Blasting Clean Heater Cores, Radiators, Heads, Intakes, & Blocks. WARNING: THIS IS A VERY POWERFUL BLASTING DEVICE
More informationCOOLING SYSTEM 7-1 COOLING SYSTEM CONTENTS
XJ COOLING SYSTEM 7-1 COOLING SYSTEM CONTENTS page GENERAL INFORMATION COOLANT... 3 COOLANT TANK... 2 COOLING SYSTEM... 1 ENGINE ACCESSORY DRIVE BELTS... 2 LOW COOLANT LEVEL SENSOR... 3 RADIATOR... 2 WATER
More informationThis document is brought to you through the kind services of
This document is brought to you through the kind services of Kevin Wright krwright@wankel.net http://www.wankel.net/~krwright who, well, didn t do much this time, since Paul ee provided the thing already
More information82. Siphon all gas out of the tank. 83. Disconnect the fuel filler and vent tube with a Phillips screwdriver.
Chapter 5 - Gas Tank Removal, Cleaning, Sealing (Video Clip 5) 81. Gas tank removal and cleaning and sealing was completed using the Eastwood Gas Tank Sealer Kit. Other items required included (Purchase
More informationLincoln Mark VII Cooling Systems
Lincoln Mark VII Cooling Systems Written By Kit Sullivan March 15, 2003 Wow! That car is hot! If spoken in regards to your classic muscle-car s ability to elicit complimentary remarks, you are all set!
More informationHeater with Air Conditioning. E-Series Ford Aeromaster
Service Guide Heater with Air Conditioning E-Series Ford Aeromaster Contents Blower Motor...2 Plenum Removal...3 Control Module...6 Servo Motors...8 Coolant Valve and Servo Motor...8 Evaporator Recirculation
More informationUSER MANUAL PLEASE READ THROUGH ALL INSTRUCTIONS BEFORE USE ANY FURTHER QUESTIONS PLEASE CALL OUR TECHNICAL HELP LINE:
USER MANUAL PLEASE READ THROUGH ALL INSTRUCTIONS BEFORE USE ANY FURTHER QUESTIONS PLEASE CALL OUR TECHNICAL HELP LINE: 0870 428 0075 CONTENTS Page 2 - Unpacking Page 3 - Heating system preparation and
More informationP/N CC-100. Coolant Circulator. Operation manual
P/N 4411-0019 CC-100 Coolant Circulator Operation manual Manual Version 1 Revision B July 1, 1998 Table of Contents Chapter 1 Introduction... 5 Description...5 Specifications...5 Chapter 2 Warnings...
More informationCAUTION UM120W (RIGHT TANK) FOR WATER BORNE PAINTS ONLY UM120W (RIGHT TANK) SECTION IS NOT DESIGNED FOR USE WITH SOLVENT BASED PAINT
OPERATING MANUAL SOLVENT AND WATER BASE SPRAY GUN CLEANER UG5000W and UG5500W CAUTION UM120W (RIGHT TANK) FOR WATER BORNE PAINTS ONLY UM120W (RIGHT TANK) SECTION IS NOT DESIGNED FOR USE WITH SOLVENT BASED
More informationHeating and Cooling Systems
Heating and Cooling Systems Figure 1. Typical Engine Cooling System Introduction Engines generate a great amount of heat. This heat is created when the fuel and air mixture is ignited and expands inside
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SNA-100 2007 CIVIC 2 AND 4-DOOR (DX, LX, EX) AII 33542 Issue Date AUG 2006 PARTS LIST Engine block heater Aluminum
More informationWalk-in Refrigerated Rooms. An Overview of Requirements, Options and Construction Details
Walk-in Refrigerated Rooms An Overview of Requirements, Options and Construction Details Definition A refrigerated room is a stand alone structure designed to hold products at either a medium temperature
More informationInstallation, Operation and Maintenance Manual
Installation, Operation and Maintenance Manual Packaged Chiller Models CC 6601, 6501, 6401, 6301, 6201, 6101 For Service, please contact Pfannenberg Service Company: U.S.A. Pfannenberg Inc. 68 Ward Road.
More informationChapter 3 Cooling, heating and ventilation systems
3 1 Chapter 3 Cooling, heating and ventilation systems Contents Antifreeze mixture..............................see Chapter 1 Cooling fan assembly - testing, removal and refitting.............8 Cooling
More informationGuide to the Heating and Cooling Systems at McLean Gardens
MCLEAN GARDENS Guide to the Heating and Cooling Systems at McLean Gardens How They Function and Their Maintenance Version 1.0 5/21/2013 This document explains the McLean Gardens heating and cooling system
More informationSECTION AUXILIARY HEATER
14-301.03/ 1 2010MR12 SECTION 14-301.03 GENERAL DESCRIPTION The Thermo 300 auxiliary heating system is used in conjunction with the vehicle s heating system, in order to heat the passenger compartment
More informationUSER MANUAL. Danfoss Heat Pump DHP-R VUIFK102
USER MANUAL Danfoss Heat Pump DHP-R VUIFK102 Table of contents 1 Important information........................................................... 4 1.1 Safety precautions...4 1.2 Protection...4 2 About
More informationUser s Information Manual
User s Information Manual Gas-Fired Water Boilers With or without Aqua Logic (CWH) Now available Matching High Performance Companion Water Heater (Unit sold separately) If the information in this manual
More informationAUTOMOTIVE SPECIALIZATION (Air Conditioning and Heating) STUDENT GRADE RECORD Career & Technical Education
STUDENT GRADE RECORD Career & Technical Education Course Outline Modules Windham Module Test Module Competenc y Rating WINDHAM SCHOOL DISTRICT 1. CTE Orientation 2. Introduction to Automotive Heating,
More informationLabel Placement Guide P/N IMPORTANT! Read contents carefully prior to operation.
Label Placement Guide IMPORTANT! Read contents carefully prior to operation. RECOMMENDED WARNING LABEL PLACEMENT ON TAYLOR MACHINES PLACEMENT OF LABELS MAY VARY DUE TO CONSTRUCTION DESIGN OF MACHINES.
More informationInnovative cleaning with dry ice: No residue, no chemicals.
Ice Blaster - Dry Ice Cleaning Specialist IB 15/80 Ice Blaster Innovative cleaning with dry ice: No residue, no chemicals. IB 15/80 Ice Blaster A trendsetting method of cleaning With its innovative IB
More informationLaboratory Freeze Dryer CRYODOS
MAINTENANCE MANUAL Laboratory Freeze Dryer CRYODOS CRYODOS_I_rev005MA Telstar Industrial, S.L. Josep Tapiolas, 0 086 TERRASSA (Spain) Tel. +34 937 36 6 00 Fax: +34 937 85 93 4 telstar@etelstar.com www.etelstar.com
More informationDTC P1441 Evaporative Emission (EVAP) System Flow During Non- Purge
Page 1 of 10 Your Current Vehicle: 1996 Chevrolet Camaro DTC P1441 Evaporative Emission (EVAP) System Flow During n- Purge NOTE Applicable vehicles: Camaro, Firebird (VIN F) DTC P1441 Evaporative Emission
More informationTRADE OF HEAVY VEHICLE MECHANIC
TRADE OF HEAVY VEHICLE MECHANIC PHASE 2 Module 3 Engine UNIT: 4 Table of Contents 1. Learning Outcome... 1 1.1 Key Learning Points... 1 2. Cooling Fundamentals... 2 2.1 Cooling systems... 2 2.2 Heat transfer...
More informationCPC-150-ANA. 150 litres, 535mm x 1300mm high. Pandora Heat Bank. 100kW Plate Heat Exchanger with 22mm Thermostatic Mixing Valve.
6 8 9 10 1 3 7 2 4 11 13 14 5 Wiring Pandora Heat Bank. 100kW Plate Heat Exchanger with 22mm Thermostatic Mixing Valve. Manually Filled store - NO discharge pipe or overflow. 100kW Plate Heat Exchanger
More informationSAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions carefully. 2. DANGER! To protect against risk
More informationTT /97 WARNING WARNING WARNING INSTALLATION INSTRUCTIONS
TT-116 2/97 INSTALLATION INSTRUCTIONS Original Issue Date: 2/97 Model: 900/1000 kw Market: Industrial Subject: Block Heater Kits PA-28648, PA-28648-SD The block heater kit heats engine coolant, making
More informationExtrusion Walkthrough
Extrusion Walkthrough Our experiences with the extrusion of polyethylene terephthalate (PET). Contents The Extrusion of PET... 2 Shredding PET... 2 Shredding PET... 3 Starting up... 3 Cleaning the extruder...
More informationV-220 / V-320 Heater Kits Installation Instructions TK IM (Rev. 0, 06/17)
Installation Manual V-220 / V-320 Heater Kits Installation Instructions TK 56340-18-IM (Rev. 0, 06/17) Installation Manual V-220 / V-320 Heater Kits Installation Instructions TK 56340-18-IM (Rev. 0, 06/17)
More informationSAFETY OPERATION & MAINTENANCE MANUAL X-405 CARPET EXTRACTOR This unit is intended for commercial use.
SAFETY OPERATION & MAINTENANCE MANUAL X-405 CARPET EXTRACTOR This unit is intended for commercial use. READ AND FOLLOW ALL INSTRUCTIONS, WARNINGS AND CAUTIONS BEFORE USING THIS EXTRACTOR Address: 777 South
More informationHEATING AND VENTILATION
SECTION 14-102.04 14-102.04/ 1 2007OC19 DESCRIPTION The heating, ventilation and air conditioning (HVAC) system is designed to optimize passenger comfort. The system regulates interior vehicle atmosphere,
More informationG-7s. Instruction Manual. G-Series Cooler COUNTERTOP COOLER. Part No.11IPA
G-Series Cooler COUNTERTOP COOLER Part No.11IPA-061000 Instruction Manual FOR YOUR FUTURE REFERENCE This easy-to-use manual will guide you in getting the best use of your cooler. Remember to record the
More information6.4L Oil Cooler Service Tips
General Service Bulletin (GSB): This GSB will assist in diagnosing the Some 6.4L oil coolers become restricted after replacement due to root cause of an oil cooler improper inspection prior to replacement
More informationThe Flush Kit: The perfect companion to Harvest Right home freeze dryers. The Flush Kit. User s Manual
The Flush Kit: The perfect companion to Harvest Right home freeze dryers The Flush Kit User s Manual Freeze Dryer Accessories LLC 2608 W. 510 N. Hurricane, UT 84737 (435)215-5136 web: freezedryeraccessories.com
More informationDIRECT DRAW BEER COOLERS Installation, Operation and Maintenance Instructions
DIRECT DRAW BEER COOLERS Installation, Operation and Maintenance Instructions INSPECTION When the equipment is received, all items should be carefully checked against the Bill of Lading to ensure all crates
More informationTWINTEMP JR. HYDRONIC SYSTEM 2/2013
TWINTEMP JR. HYDRONIC SYSTEM 2/2013 TwinTemp Description of Operation and Sequence of Operation Technical Description of Operation The TwinTemp systems provide quiet space heating utilizing liquid to air
More informationCU20 Water Circulator
Water Circulator Description Water Cooling System Important Information All persons authorised to use, repair or service the Water Circulator unit, should read the section on safety, before any work is
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 41826 ENGINE BLOCK P/N 08T44-SNA-101 2010 ODYSSEY Issue Date JUNE 2009 PARTS LIST Engine block heater Aluminum washer NOTE Always use
More informationUPP7500E2 AUTOMATIC PRESSURE POT CLEANER
USER MANUAL UPP7500E2 AUTOMATIC PRESSURE POT CLEANER UNI-RAM CORPORATION ONTARIO CANADA REV 2012-12 INTRODUCTION Uni-ram holds many patents on designs used in its innovative products. Every machine is
More informationChef Base Refrigerators
Chef Base Refrigerators Service, Installation and Care Manual Please read this manual completely before attempting to install or operate this equipment. Notify carrier of damage! Inspect all components
More information10,000 prize draw. instructions. EXTRA year guarantee FREE rewards gallery. Register online now!
instructions 10,000 prize draw EXTRA year guarantee FREE rewards gallery www.productregister.co.uk/rhobbs Register online now! See back for details Read the instructions, keep them safe, pass them on if
More informationinfrared paraffin / kerosene / diesel heater
instructions for infrared paraffin / kerosene / diesel heater model no: IR20.V3 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
More informationUnvented Calorifier Range. Operating and Maintenance Manual. For Models & 500
Unvented Calorifier Range. Operating and Maintenance Manual. For Models 125 300 & 500 Telephone 08456 448802 Fax 08456 448803 Emial info@mhgheating.co.uk Web www.mhgheating.co.uk TABLE OF CONTENTS. Section
More informationThis site is based on a but applies to all 1971-on Saab 99 and Saab 900.
by Mark Jeter updated: December 8, 2004 originally web-published June 27, 2001 This document shows how the original waterpump in a Saab "B" engine can be eliminated and replaced with a reliable, efficient
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 30320 ENGINE BLOCK 2006 CIVIC HYBRID P/N 08T44-SVB-100 Issue Date SEP 2005 PARTS LIST Engine block heater Aluminium washer Heater harness
More informationCROWN WATER HEATERS CPU10 - CPU15 CPOS10 - CPOS15
CROWN WATER HEATERS CPU10 - CPU15 CPOS10 - CPOS15 COMPACT PLUS 10 and 15 Litre Unvented Under and Over Sink Water Heater INSTALLATION AND USER GUIDE 1 DIMENSIONS 10L - 250mm 15L - 310mm 100mm 80mm 410mm
More informationCPC-150-ABIAB. Important Installation Notes.
6 7 8 9 10 28 11 20 19 18 13 4 1 17 23 2 3 5 30 HX14 Pandora Heat Bank thermal store [] 150 litres, 530mm diameter x 1300mm high L18-14 plate heat exchanger for mains pressure hot water (30 l/min), Heatguard
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ENGINE BLOCK (L4) P/N 08T44-TA0-100 Application 2011 ACCORD 2- AND 4-DOOR Publications No. AII 43997 Issue Date AUG 2010 PARTS LIST Engine block heater 5 White wire
More informationMultipoint Technical Data
Multipoint Technical Data Multipoint 10 / 15 Specification DIMENSIONS AND PERFORMANCE Model Multipoint 10 vertical Multipoint 15 vertical Multipoint 10 4.5kW vertical Multipoint 15 4.5kW vertical A - Height
More informationMODEL A5-2 SOLVENT & WATER RECOVERY SYSTEMS (EXPLOSION PROOF UNITS)
MODEL A5-2 SOLVENT & WATER RECOVERY SYSTEMS (EXPLOSION PROOF UNITS) FOR PROPER AND SAFE USE OF THIS CHEMCHAMP EQUIPMENT, PLEASE FOLLOW THIS DOCUMENT AND LOCAL AUTHORITY. KEEP THIS DOCUMENT FOR FUTURE REFERENCE.
More informationIce Cone Freezing Experiment. OilExTech LLC
Ice Cone Freezing Experiment July/August 2017 George Hackleman OilExTech LLC Freezing of water ice in the EssenEx Ice Cone forms. Some customers are interested in knowing more detail around how to freeze
More information